MC1458

High-performance, dual operational amplifier

Datasheet - production data

Applications
Summing amplifier
Voltage follower
Integrator
Active filtering
Function generator

Description
The MC1458 is a high-performance, monolithic,
dual operational amplifier intended for a wide
Features range of analog applications. The high gain and
Low power consumption wide range of operating voltages provide superior
Large input voltage range performance in integrator, summing amplifiers,
No latch-up and general feedback applications.
High gain
Short-circuit protection
No frequency compensation required

September 2016 DocID2172 Rev 4 1/12

This is information on a product in full production. www.st.com
Contents MC1458

Contents
1 Schematic diagram.......................................................................... 3
2 Package pin connections................................................................ 4
3 Absolute maximum ratings............................................................. 5
4 Electrical characteristics ................................................................ 6
5 Package information ....................................................................... 8
5.1 SO8 package information .................................................................. 9
6 Ordering information..................................................................... 10
7 Revision history ............................................................................ 11

2/12 DocID2172 Rev 4

MC1458 Schematic diagram

1 Schematic diagram
Figure 1: Schematic diagram

DocID2172 Rev 4 3/12

Package pin connections MC1458

2 Package pin connections

Figure 2: Pin connections (top view)

4/12 DocID2172 Rev 4

MC1458 Absolute maximum ratings

3 Absolute maximum ratings

Table 1: Absolute maximum ratings
Symbol Parameter MC1458DT MC1458IDT Unit
VCC Supply voltage ±22
Vi Input voltage ±15 V
Vid Differential input voltage ±30
Output short-circuit duration Infinite
Ptot Power dissipation 300 mW
Toper Operating free-air temperature range 0 to 70 -40 to 105
°C
Tstg Storage temperature range -65 to 150

DocID2172 Rev 4 5/12

Electrical characteristics MC1458

4 Electrical characteristics
Table 2: Electrical characteristics for VCC = ±15 V, Tamb = 25 °C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit

Input offset voltage, Tamb = 25 °C 1 5

Vio mV
Rs ≤ 10 kΩ Tmin ≤ Tamb ≤ Tmax 6
Tamb = 25 °C 2 200
Iio Input offset current
Tmin ≤ Tamb ≤ Tmax 300
nA
Tamb = 25 °C 30 500
Iib Input bias current
Tmin ≤ Tamb ≤ Tmax 800
Large signal voltage gain, Tamb = 25 °C 50 200
Avd V/mV
Vo = ±10 V, RL = 2 kΩ Tmin ≤ Tamb ≤ Tmax 25
Supply voltage rejection Tamb = 25 °C 77 90
SVR dB
ratio, Rs ≤ 10 kΩ Tmin ≤ Tamb ≤ Tmax 77
Supply current, all amp, Tamb = 25 °C 2.3 5
ICC mA
no load Tmin ≤ Tamb ≤ Tmax 6
Input common-mode voltage Tamb = 25 °C ±12
Vicm V
range Tmin ≤ Tamb ≤ Tmax ±12
Common-mode rejection Tamb = 25 °C 70 90
CMR dB
ratio, Rs ≤ 10 kΩ Tmin ≤ Tamb ≤ Tmax 70
Ios Output short-circuit source Tamb = 25 °C 10 20 35 mA
Tamb = 25 °C, RL ≤ 10 kΩ 12 14
Tamb = 25 °C, RL ≤ 2 kΩ 10 13
±Vopp Output voltage swing V
Tmin ≤ Tamb ≤ Tmax, RL ≤ 10 kΩ 12
Tmin ≤ Tamb ≤ Tmax, RL ≤ 2 kΩ 10
VI = ±10 V, RL = 2 kΩ, CL = 100 pF,
SR Slew rate 0.2 0.8 V/µs
unity gain
VI = ±20 mV, RL = 2 kΩ, CL = 100 pF,
tr Rise time 0.3 µs
unity gain
VI = ±20 mV, RL = 2 kΩ, CL = 100 pF,
KOV Overshoot 5 %
unity gain
RI Input resistance 0.3 2
MΩ
Zic Common-mode input impedance 200
CI Input capacitance 1.4 pF
RO Output resistance 75 Ω
RL = 2 kΩ, VO ≥ ±10 V, AVD = 1,
FPB Full power bandwidth 14 kHz
THD ≤ 5 %
B Unity gain bandwidth VI = 10 mV, RL = 2 kΩ, CL = 100 pF 1
VI = 10 mV, RL = 2 kΩ, CL = 100 pF, MHz
GBP Gain bandwidth product 0.4 1
f = 100 kHz
f = 1 kHz, Av = 20 dB, RL = 2 kΩ,
THD Total harmonic distortion 0.02 %
CL = 100 pF, VO = 2 Vpp

6/12 DocID2172 Rev 4

MC1458 Electrical characteristics
Symbol Parameter Min. Typ. Max. Unit
Equivalent input noise
en f = 1 kHz, Rs = 100 Ω 45 nV/√Hz
voltage
ɸm Phase margin 65 Degrees
Am Gain margin 11
dB
Vo1/Vo2 Channel separation 120

DocID2172 Rev 4 7/12

Package information MC1458

5 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK ®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.

8/12 DocID2172 Rev 4

MC1458 Package information

5.1 SO8 package information

Figure 3: SO8 package outline

Table 3: SO8 mechanical data

Dimensions
Ref. Millimeters Inches
Min. Typ. Max. Min. Typ. Max
A 1.75 0.069
A1 0.10 0.25 0.004 0.010
A2 1.25 0.049
b 0.28 0.48 0.011 0.019
c 0.17 0.23 0.007 0.010
D 4.80 4.90 5.00 0.189 0.193 0.197
E 5.80 6.00 6.20 0.228 0.236 0.244
E1 3.80 3.90 4.00 0.150 0.154 0.157
e 1.27 0.050
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
L1 1.04 0.040
k 0° 8° 0° 8°
ccc 0.10 0.004

DocID2172 Rev 4 9/12

Ordering information MC1458

6 Ordering information
Table 4: Order codes
Order code Temperature range Package Packaging Marking
MC1458DT 0 °C to 70 °C 1458
SO8 Tape and reel
MC1458IDT -40 °C to 105 °C 1458I

10/12 DocID2172 Rev 4

MC1458 Revision history

7 Revision history
Table 5: Document revision history
Date Revision Changes
Moved part number MC1558 to a separate datasheet.
Removed DIP8 package
Deleted “Device summary table”, created Table 4: "Order codes" in its
21-Sep-2016 4
place, and added the latter to Section 6: "Ordering information".
Updated Section 5.1: "SO8 package information"
Updated document layout

DocID2172 Rev 4 11/12

 MC1458

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST
products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the
design of Purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2016 STMicroelectronics – All rights reserved

12/12 DocID2172 Rev 4