Available online www.jsaer.

com

Journal of Scientific and Engineering Research, 2015, 2(2):40-51

ISSN: 2394-2630
Research Article CODEN(USA): JSERBR

Assessment of Qualities of Coarse Aggregate Used in Concrete Production in Anambra

State, Nigeria

Ezeokonkwo John U, Okolie Kelvin Chuks, Ogunoh Peter

Department of Building Nnamdi Azikiwe University, Awka, Anambra State, Nigeria

Abstract Concrete fails when it can no longer provide the required strength to support its designed load. This
failure can be mild with visible cracks and deflections or severe, leading to partial or total collapse of the
structure either during the construction or post- construction stage. It has been observed that the major cause of
this collapse is the use of sub- standard materials mainly poor quality of stone aggregates materials used for
concrete production. Previous study on this area centred mainly on other causes of building collapse, with little
'emphasis on coarse aggregate. Therefore, the study is aimed at establishing the qualities of coarse aggregate
sourced within Anambra State. Primary and secondary data were used for this study. Samples for the laboratory
experiment were obtained from quarry sites at Enugwu-ukwu, Aguleri, Nsugbe, Nikwelle–Ezunaka and
Ogbunka. Sieve analysis, Slump test and Cube (crushing strength) were performed using each of the samples.
The study observed that the crushing strength and/or compressive strength of the samples at 7 day are between
20-29N/mm' with Ogbunka samples having the highest compressive strength of 29.33N/mm2. Thus, at 7th day,
four out of the five samples tested have attained the minimum strength of boncrete (i.e. 21N/mm'). For
workability test, the study observed that the percentage of slump for the samples ranges from 21.5 – 41% with
Nsugbe samples having the best slump value of 21.5%, For sieve analysis, the researchers observed that the
samples were fairly graded. The percentage of the grains passaging through 19.05 diameters is between 64.3 –
84.0%. The study ended with the following recommendations that stones should be properly graded using
machines rather than hand breaking. Also stones should be properly washed before using them since most of
them are coated with impurities and other clayey substances and muds which may interfere with the process of
bonding. Finally, more research should be carried out using un-wash samples from other quarry sites/towns not
covered by this study.

Keywords Concrete, coarse aggregate, compressive strength, Anambra state, quarry site.

1. Introduction
Concrete is arguably the most important building material, playing a part' in all building structures [6]. Its virtue is:
versatility, i.e. its ability to be molded to take up the shapes required for the various structural forms, durability
and fire resistant when specification aid construction procedures are correct [6]. Based on its properties i.e.
strength, rigidity and easy formability, coupled with the easy availability of the component materials, have
made concrete the material of choice for architects, engineers, builders and project owners.
The three basic component of concrete – cement, aggregate and water greatly affect the quality of concrete [4].
Aggregate occupy about 70-80 per cent of the volume and this considerably influence the properties of the
concrete [4]. In line with this [9] opined that "The compressive strength of concrete cannot exceed that of the
aggregate used therein."

Journal of Scientific and Engineering Research

40
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

Aggregates as defined by [9] UNESCO-NT&VERP, (2008) are "materials comprising of percentage required of
gravel, crushed stone and natural sharp sand of their specific size of particle mixed together at a required ratio
to form part of concrete mortar." Aggregate used in construction basically comes in two different sizes-the bigger
ones known to be coarse aggregate (grit) and the smaller ones fine aggregate (sand) [4]. The coarse aggregate
forms the main matrix of concrete and the fine aggregate form the filler matrix between the coarse aggregate [4].
Since approximately 80 percent of the total volume of concrete consists of aggregate, aggregate characteristics
significantly affect the performance of fresh and hardened concrete and have an impact on the cost effectiveness
of concrete [8]. Aggregate characteristics of shape, texture, sand grading influence workability, finishability,
bleeding, pumpability, and segregation of fresh concrete and affect strength, stiffness, shrinkage, creep, density,
permeability, and durability of hardened concrete. Construction and durability problems have been reported due to
poor mixture proportioning and variation on [8].

1.1. Statement of the Problem

Concrete fail when it can no longer provide the required strength to support its designed load [3,5]. The failure
of Concrete can sometimes be mild with visible cracks and deflections or severe crack, leading to partial or total
collapse of the structure either during the construction or post- construction stage. Incidences of failures of structures
linked to bad concrete practice are abounding in Nigeria particularly in our major cities such as Lagos, Port-
Harcourt, and Abuja, among others. The findings of the committee of enquiry that investigated the collapsed of
four-storey building at Okpuno, Awka, Anambra state capital in September 2008 reported that the building
collapsed the same day the casting of the concrete third floor slab was concluded. The incident, took the lives of four
persons. The report further revealed that among the causes of the collapse was the use of sub- standard materials'
stating that - poor quality of stone aggregates materials were used for concrete production [2].

In order to curb the incidence of building collapse across the globe, several researches has been carried out at
different time by different individuals, corporate bodies and civic society to ascertain the strength and/or
quality of materials used in concrete production. Attention mainly is placed on reinforcements and cements,
with little on the aggregates. However, in Anambra state little research has been made in order to ascertain the
quality of the coarse aggregate sourced within.

1.2. Aim and Objectives

The aim of this research is to establish the qualities of coarse aggregate sourced within Anambra State.
The research aim was achieved using the following objectives, to:
 Established qualities of good coarse aggregate, possible tests and procedures.
 Identify quarry sites within state.
 Obtain specimen samples (i.e. coarse aggregate) from these quarry sites and investigate in the laboratory
their compressive strengths, aggregates particle size distribution and slump test to determine their suitability
in the production of concrete.

2. Review of related Literature

2.1. Aggregates
An aggregate according to UNESCO-NT&VERP, (2008), [9] can be defined as the material comprising of
percentage required of gravel, crushed stone and natural sharp sand of their specific size of particle mixed together
at a required ratio to form part of concrete mortar. To Council of Registered Builders of Nigeria (CORBON)
and Nigeria Institute of Building (NIOB), (2014) [3], Aggregates are the granular filler material such as sand,
stone dust, gravel, crushed stone, crushed blast-furnace slag, etc. that are used with binder such as Portland
cement to produce concrete or mortar.
It includes boulders, cobbles, crushed stone, gravel, air-cooled blast furnace slag, native and
manufactured sands, and manufactured arid natural lightweight aggregates [1]. The aggregate (both fine and
coarse) makes up about 80% of the volume of the concrete [10]. Reed, Schoonees and Salmond [10]
generalized the volume of aggregate in concrete production but Aker (2000) [1] was more specific. According
to Aker, (2000) [1], in a Portland-cement, concrete mix, coarse and fine aggregates occupy about 60 to 75% of

Journal of Scientific and Engineering Research

41
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

the total mix volume and for - asphaltic concrete, aggregates represent 75 to 85% of the mix volume. But Anosike,
2011 [2] state that in any Concrete, aggregates (fine sand and coarse) usually occupies about 70-75%. Thus,
aggregate generally occupy about 60-80% of the total concrete volume.
Aggregates are used in concrete to; increase its volume, increase strength and durability, red ice shrinkage,
reduce creep, reduce overall cost, imparts sound and thermal properties, imparts density, increase chemical
resistance etc [3]. When aggregate for concrete is being selected, the chemical inertness, strength, clean, cost,
availability in required size, grading, shape and surface texture are considered [3]. Also, Anosike (2011), [2]
opined that While selecting aggregate for a particular concrete, the economy of the mixture, the strength of the
hardened mass and durability of the structure must first be considered.

2.2. Classification of Aggregate

Anosike (2011); Duggal (2008); Ezeokonkwo (2013) [2,4,5] classified aggregate based on the source
(Natural and artificial aggregates); According to mineralogical composition (aggregates here are classified as
siliceous or calcareous); According to mode of preparation (in this situation distinction is made between
aggregates reduced to its present size by natural agents and crushed aggregates obtained by a deliberate
fragmentation of rock); According to size (divided again into coarse and fine aggregates). CORBON and
NIOB, (2014); McGinley & Choo (2003) [3,6] classified aggregate only in terms of size. Finally UNESCO-
NT&VERP (2008) [9] classified aggregate based on origin with other subdivisions.

However, for the purpose of this work, the classification based on size will be adopted. Namely:
i. coarse aggregate-gravel or crushed rock 5 mm or larger in size
ii. fine aggregate-sand less than 5 mm in size
Coarse Aggregate: Aggregate retained on 4.75 mm sieve is identified as coarse [3,4]. They are obtained by
natural disintegration or by artificial crushing of rocks. The maximum size of aggregate can be 80 mm. It
ranges between 20mm-10mm [9]. Particles with larger sizes cause reduction in strength of concrete [9]. The size
is governed by the thickness of section, spacing of reinforcement, clear cover, mixing, handling and placing
methods [4].
Fine Aggregate: Aggregate passing through 4.75 mm sieve are defined as fine [4,3]. Alternatively,
UNESCO-NT&VERP (2008), [9] defined fine aggregate as particle's passing 25mm which are retained on
a 600 microns sieve. They may be natural sand ' deposited by rivers, crushed stone sand-obtained by
crushing stones and crushed gravel sand. The smallest size of fine aggregate (sand) is 0.06 mm.

2.3. Properties of Aggregate:

The properties to be considered while selecting aggregate for concrete is grouped into two: mechanical
and physical properties.

2.3.1. Mechanical Properties of Aggregates

a) Bond Strength of Concrete: The resistance developed to shear particles from the hardened cement paste is
called bond strength of aggregate. Bond is partly due to the interlocking of the aggregates and the paste
owing to the roughness of the surface of the aggregate particle. A rougher texture as that of crushed stone
results in a greater adhesion or bond between the particles and the cement matrix. Generally, when bond is
good, a crushed concrete specimen should contain some aggregate particles broken right through, in
addition to the more numerous ones separated from the paste matrix. However, an excess of fractured
particles suggests that the aggregate is too weak. Bond strength is found to increase with the age of the
concrete. The strength of concrete is therefore dependent on the bond strength.
b) Crushing Strength of Aggregate: The compressive strength of concrete cannot exceed that of the
aggregates used therein. Usually, aggregate is considered ten times stronger than the crushing strength of
concrete, but some particles break also and influence its strength. Therefore, aggregate to be used in cement
concrete-should not be weaker than the strength of hardened cement paste. BS 882:1992-prescribes a minimum
value of 150KN (15 tons) for aggregate to be used in heavy duty concrete floor finishes, 100KN (10 tons) for

Journal of Scientific and Engineering Research

42
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

aggregate to be used in concrete pavement wearing surface, and 50KN (5 tons) when used in other concretes.
In addition CORBON and NIOB (2014), [3] classified concrete based on its crushing strength as:
High-strength concrete, concretes with compressive strengths: greater than 60N/mm 2 (9000psi) at 28
days or 56 days (age depends on the specification). Other higher classes of high strength concrete are
the ultrahigh strength and high performance concretes: Normal-strength (also called ordinary or
moderate-strength) concretes, concretes with 28-day compressive strengths of between 20 to 60N/mm 2
(3000 to 9000psi). They are used for normal structural work. The normal strength concretes are divided
into various strength grades for different structural uses: Low-strength concretes, concretes' with 28-day"
compressive strengths of less than 20N/mm 2 , (3000psi), Used where light loading is expected e.g.; for
stabilization of embankments, strip footings, ordinary ground floor slabs, etc.

2.3.2. Physical Properties of Aggregates

a) Absorption, Porosity, and Permeability: The porosity, permeability and absorption in aggregates
influence the bond between it and the cement paste, the resistance of concrete to freezing and thawing, as well
as chemical stability, resistance to abrasion and specific gravity [9]. Absorption relates to the particle's-
ability to take in a liquid. Porosity is a rate of the volume of the pores to the total volume of the particle.
Permeability refers to the particle's ability to allow liquids to pass through.
The porous aggregate absorb more moisture, resulting in loss of workability of concrete at a much faster rate
[4]. High moisture content increases the effective water/cement ratio to an appreciable extent and may render
the concrete weak [4].Absorption and Surface Moisture affects Mix-design, Soundness, and
Strength/abrasion resistance [6].
The water absorption is determined by measuring the decrease in mass of a saturated and surface-dry sample
after oven drying for 24 hours. The ratio of the decrease in mass of the dry sample expressed as a percentage
is termed absorption [9].
b) Surface Texture a nd Shape: Surface texture is the pattern and the relative roughness or
smoothness of the aggregate particle. Surface texture plays a big role in developing the bond between an
aggregate particle and a cementing material. The shape of the aggregate will also affect the workability of
the concrete. An extremely rough, angular aggregate is less workable and may require more water to be added
to the mix to increase its workability, thus reducing strength and producing, a more porous concrete [10]. Also,
Mehta and Monteiro, [6] stated Rough-textured and elongated particles require more cement paste to produce
workable concrete mixtures, thus increasing the cost.
A rough surface texture gives the cementing material something to grip, producing a stronger bond, and thus
creating a stronger hot mix asphalt or Portland cement concrete. Surface texture also affects the workability
of hot mix asphalt, the asphalt requirements of hot mix asphalt, and the water requirements of Portland
cement concrete.
c) Strength and Elasticity: Strength is a measure of the ability of an aggregate particle to stand up to
pulling or crushing forces. Elasticity measures the "stretch" in a particle. The strength of the aggregate should
be at least equal to that of the concrete [4]. To Anosike (2011) [2] aggregates are considered to be ten times
-
stronger than the crushing strength of concrete, but some particles break also and influence its strength.
Rocks commonly used as aggregates have a compressive strength Much higher than the usual range of
concrete strength [4].The tests conducted for strength evaluation are crushing test, impact-test and ten per cent
fines test [4]. BS 882: 1992 prescribes a minimum value of 150KN (15 tons) for aggregate to be used in
heavy duty concrete floor finishes, 100KN (10 tons) for aggregate to be used in concrete pavement wearing
surface, and 50KN (5 tons) when used in other concretes.
d) Density and Specific Gravity: Density is the weight per unit of volume of a substance. Specific
gravity is the ratio of the density of the substance to the density of water. The specific gravity and porosity
of aggregates greatly influence the strength and absorption of concrete. Specific gravity of aggregates generally
is indicative of its quality. A low specific gravity may indicate high porosity and therefore poor durability and
low strength.

Journal of Scientific and Engineering Research

43
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

The bulk density of aggregate depends upon their packing, the particles shape and size, the grading and the
moisture content. For coarse aggregate a higher bulk density is an indication of fewer voids to be filled by sand
and cement:

Table 1: Specific Gravity of Cement and Aggregates

Material Specific Gravity
Cement 3.15
Average Sand 2.00
Granite 2.80
Gravel 2.66
Sand 2.65
Source: Anosike, (2011) [2]

Specific Gravity
3.5
3
2.5
2
1.5
1
0.5
0 Specific Gravity

Figure 1: Specific Gravity of Cement and Aggregates

e) Aggregate Voids: With respect to a mass of aggregate, the terms voids refer to the space between the
aggregate particles: Numerically this voids space is the difference between the gross volume of aggregate
mass and the space occupied by the particles alone. The voids wit hin an aggregate particle should not be
confused with the void system which makes up the space between particles in an aggregate mass. The voids
between the particles influence the design of hot mix asphalt or Portland cement concrete and/or strength. To
this end, Duggal, (2008) [4] affirms that "if the voids in the concrete are more the strength will be low."
f) Undesirable Physical/Chemical Components (Deleterious Substance): Deleterious substances are
impurities capable of causing damage to the immediate environment where they occur [2]. Particles with
undesirable physical characteristics include but are not limited to the following:
 Non-durable soft or structurally weak particles
 Clay lumps or clay balls -
 Flat or elongated particles
 Organic matter contaminants
 Lightweight chest
The effects of deleterious materials on aggregates according to Anosike, (2011) [2] are: They interfere with
the hydration of cement; they affect bond between cement paste and aggregates; they reduce the strength and
durability of concrete; they modify the setting action of cement concrete and contribute to efflorescence.

2.4. Testing of Aggregate

The size, shape, grading of aggregate and their surface moisture affect directly the workability and strength of
concrete whereas soundness, alkali-aggregate reaction and presence of deleterious substances adversely

Journal of Scientific and Engineering Research

44
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

affect the soundness and durability of concrete. The following tests are conducted to ensure satisfactory
performance of aggregate.
a) Particle Size Distribution Test/Grading: The grading of coarse aggregate is of a vital factor in
determining the determining the properties of concrete, since it influences to a large extent the degree of
pores contained in the hardened concrete [7].Grading and size of aggregate both affect the amount of water
needed to obtain workability. A well-graded aggregate, i.e. one with a range of particle size, improves the
workability, as does using the largest possible particle size that can be compacted around and over the
reinforcing rods [10].
The process of dividing a sample of aggregate into fractions of same particle size is known as a sieve analysis,
and its purpose is to determine the grading or particle size distribution of the aggregate.
A sample of air-dried aggregate is graded by shaking or vibrating a nest of stacked sieves with the largest
sieve at the top, for a specified time so that the Material retained on each sieve represents the fraction coarser
than the sieve in question but finer than the sieve above. Usually sieve sizes for concrete aggregate are 75.0,
50.0, 37.5, 20.0, 10.0, 5.0, 2.36, 1.18mm and 600, 300 and 150micron [9].
The air dried sample is placed on a set of specific sieves with largest size on the top. The set of sieve is
shaking for 2 minutes; Arrangement of sieve for coarse aggregate is as follows: 40mm, 20mm 16mm l0mm 4.75
mm 2.36 mm [9]. Table 2 gives the grading requirement for coarse aggregate

Table 2: Grading Requirements for Coarse Aggregate Concrete (ASTM C-637)

Sieve Size Grading (37.5mm max-size Grading (19.0mm max-size
Aggregate) Aggregate)
Coarse Aggregate
50min , 100 -
37.5min 95-100 100
25.0mm 40-80 95-100
19.0mm 20-45 40-80
12.5mm 0-10 0-15
9.5mm 0-2 0-2
Source: Anosike, (2011) [2]
Finally a curve should be plotted with sieve sizes on abscissa on a graph and percentage of aggregate passing as
ordinate. From this graph relative amount of various sizes of aggregate can be readily compared.

b) Deleterious Materials and Organic Impurities Test: Harmful substances that may be present in
aggregates include organic impurities, silt, clay, shale, iron oxide, coal, lignite; and certain lightweight and soft
particles [4]. UNESCO-NT&VERP, (2008); Duggal, (2008) [9,4] grouped these deleterious substances into
these three categories;
i.Impurities which interfere with the process of hydration of cement i.e. organic matters,
ii.Coating on aggregate which prevent the development of good bond between aggregate and the cement
paste e.g. clay. These materials should not be present in excessive quantity because they need more
water for concrete of a definite workability.
iii.Unsound or weak particles which are weak or bring about chemical reaction between
aggregate and cement paste
Aker, (2000) [1] opined that erratic setting times and rates of hardening may be caused by organic
impurities in the aggregates, primarily the sand i.e. Organic impurities may delay setting and hardening of
concrete,-may reduce strength gain, and in unusual cases may cause deterioration. Also, Coal and lignite may
also cause staining of exposed concrete surfaces [1]. Moreover, Duggal (2008) [4] postulated that impurities
affect the properties of concrete in green as well as in hardened state and are undesirable. In all, Aggregates
are potentially harmful if they contain compounds known to react chemically with Portland cement concrete
and produce any of the following:
i. Significant volume changes of the paste, aggregates, or both;

Journal of Scientific and Engineering Research

45
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

ii. Interference with the normal hydration of cement; and

iii. Other wise har mful to p rod ucts.

The acceptable international standard method of testing for their presence is provided in the last column of
the table 3.

Table 3: Limits of Deleterious Substances in Coarse Aggregates

Deleterious Substances Coarse Aggregate Method of test
uncrushed crushed
Coal and lignite 1.00 1.00 IS —2386 1963 PT II
Clay lumps 1.00 1.00 77
Soft fragments 3.00 - 71
Materials passing 3.00 1.00 PART I
75mm micron sieve
Shale - -do- Part II
Total 8.00 3.00
Source: Anosike, (2011) [2]

c) Crushing Strength Test: The strength of the coarse aggregate influence to a great extent the strength of the
concrete made from it. Due to it, UNESCO-NT&VERP, (2008), [9] posited "the compressive strength of
concrete cannot exceed that of the aggregate used therein." That is, the compressive strength of the concrete
should be equal the compressive of the coarse aggregate [10]. According to Duggal, (2008) [4], the compressive
strength of building stones in practice ranges between 60 to 200N/mm2.
Concrete compressive strength is easy to determine and for this reason it is the one most universally used in
concrete practice [3]. This strength tests is usually made on 150mm or 100mm cubes, also, 150mm diameter by
300mm cylinders are used. It has been found that cylinders fail at lower compressive stress than 100mm and
150mm cubes of the same quality of concrete [3].
The quality of concrete is generally assessed by its crushing strength. This strength is determined by testing
suitably prepared specimen of the concrete in compression machine in accordance with BS EN 12390 - 3: 2000
International Standard.
The concrete cube compressive strength can be as high as 150N/mm2 (strength still rising due to the use of
better materials procedures and technologies), but the minimum strength required for ordinary reinforced
concrete is about 21N/mm'- [3].
d) Workability Test: The quality of plastic concrete mix (fresh concrete) is assessed by workability
test. Workability is the fluidity of concrete. Generally; workability is defined as the ease with which a given set
of materials can be mixed into concrete and subsequently handled, transported - and placed with minimum
loss of homogeneity. Thus, the term workability means compatibility, placeabilty, pumpability, mobility, and
stability. Factors Affecting Workability according to CORBON and NIOB, (2014) [3] are: Aggregates
grading; Maximum aggregate size; Water/cement ratio (cement and water content); Aggregate/cement
ratio; Aggregate-shape and Aggregate texture. Workability test is carried out- in two phases, namely:
i. Slump test
ii. Co mp a ct i n g Fac to r t e st

i. Slump Test: This test together with careful observation of the concrete is the best means of
assessing workability of a mix. The slump test assists in assessing the consistency of a mix. The plasticity
and harshness is best noted by observing the appearance of the slump specimen after the mould has been

Journal of Scientific and Engineering Research

46
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

removed. A plastic mix (workable mix) will tend, to stick together and subsides unbroken when the mould is
removed, while a harsh mix breaks. Using the slump test a mix could have:
 True slump: representing mix with low to medium workability
 Shear slump : representing harsh mix, lo w cement content, poor aggregates grading,
improper shapes and textures etc.
 Collapse slump: representing mix with high workability
ii. Compacting Factor test: Slump test is satisfactory for medium and high workability. Where
concrete of very low workability is to be tested, the compacting factor test is more appropriate. This test is
done with a compacting factor apparatus. Compacting factor test measures the d egree of compaction
achieved by a standard amount of work done.

Table 4: Comparison between workability assessment methods slump and compacting factor test
Slump (mm) Compacting Factor Degree of Workability
0 --25 0.78 Very low
25-50 0.85 Low
50-100 0.92 Medium
100-175 0.95 High
Source: CORBON and NIOB, (2014) [3]
3. Research Methodology
The study evaluates the quality of aggregate from selected sources in Anambra state. Thus by adopting
sampling techniques postulated by Jude, Obiegbu, (2005), the randomly selected sample of the research were
drawn from Ogbunka (Anambra south senatorial district), Enugwukwu (Anambra Central Senatorial
District), and Aguleri, Nsugbe and Nkwelle Ezunaka (Anambra north senatorial district) respectively.
Eventually, the research survey selected and sampled one quarry sites at different locations in each of the
five towns. That is, the total of five quarry sites producing coarse aggregates were surveyed in addition
to the laboratory experiments conducted. The study sampled local stones only.
The grade of in-situ concrete specimen was 1:3:6 mix ratios with the aggregate properly washed the result
obtained from these five quarry sites and the pilot laboratory investigations conducted that was used to
represent other quarry site within the senatorial zone not surveyed. The result of the survey was used to draw
conclusions and recommendations. The study used two methods to source data:
1. Secondary Data Collection: Secondary data was used to extract relevant data and information
from texts, local and foreign journals, dissertations/thesis, technical papers, local and foreign
documents on standards, specifications, quality management and control, some selected codes of
practice, and the internet;
2. Primary Data Collection: Primary data involved field sampling and laboratory specimen tests
of some properties of concrete and materials of concrete sampled at selected quarry sites.
Sample Size: A total of 5 cubes of 150mm x 15Ornm x 150mm concrete moulds were cast, cured and tested.
All the specimens were prepared with washed aggregate samples. Two quarry sites per town were used to
conduct the laboratory experiments. Cube prepared with Enugwukwu aggregate is referred as Sample A,
Aguleri as Sample B, Nsugbe As Sample C, Ogbunka as Sample D and Nwelle Ezunaka as Sample E.

3.1. Sieve Analysis of Coarse Aggregates

Apparatus
i. Sieves, mounted on suitable frames, designed not to leak. Sieves shall conform to AASHTO M92.
ii. Mechanical sieve shaker, if used, must provide a vertical or lateral vertical motion to the sieve,
causing the particles thereon to bounce and turn so as to present different orientations to the sieving
surface. Sieve shakers must provide sieving thoroughness within a reasonable time.
iii. Oven, capable of maintaining 230 ± 9°F (110 ± 5°C). When tests are performed in the field where
ovens are not available, test samples may be dried in suitable containers over open flame or electric
hot plates with sufficient stirring to prevent overheating.

Journal of Scientific and Engineering Research

47
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

Sample Preparation
Samples were obtained in the field and reduced to test sizes. Also wet samples were spread under the sun to
dry. The original sample must be reduced to a test sample size which falls within the minimum and maximum
weight in the following table.

Summary of Test
A known weight of material, the amount being determined by the largest size of aggregate, is placed upon the
top of a group of nested sieves (the top sieve has the largest screen openings and the screen opening sizes
decrease with each sieve down to the-bottom sieve which has the smallest opening size screen for the type of
material specified) and shaken by mechanical means for a period of time. After shaking the material through the
nested sieves, the material retained on each of the sieves is weighed.

3.2. Compression Test

(i) Compression testing machine conforming to IS: 516-1959
Procedure
i. The specimens were prepared using the ratio of 1:3:6. The cubes were stored in water to cure and
were tested after 7 days.
ii. The bearing surfaces of the compression testing machine was wiped clean and any loose sand or other
material removed from the surfaces of the specimen, which would be in contact with the compression
platens.
iii. The specimen was placed in the machine in such a manner that the load could be applied to the
opposite sides of the cubes, not to the top and the bottom. The axis of specimen was carefully aligned
►
with the centre of thrust of the spherically seated platen. As the spherically seated block was
brought to rest on the specimen, the movable portion was rotated gently by hand tiller uniform
seating was obtained.
iv. The load was applied without shock and increased continuously at a rate of approximately
Ling/sq.cm/minute until the resistance of the specimen to the increasing load breaks down and no
greater load can be sustained. The maximum load applied to the specimen was recorded and the
appearance of the concrete and any unusual features in the type of failure noted.

3.3. Workability Test (Slump)

Procedure
i. The internal surface of the mould was thoroughly cleaned and applied with a light coat of oil.
ii. The mould was placed on a smooth, horizontal, rigid and non- absorbent surface.
iii. The mould was then filled in four layers with freshly mixed concrete, each approximately to one-fourth
of the height of the mould.
iv. Each layer was tamped 25 times by the rounded end of the tamping rod (strokes are distributed
evenly over the cross- section).
v. After the top layer is rodded, the concrete was struck off the level with a trowel.
vi. The mould was removed from the concrete immediately by raising it slowly in the vertical direction.
vii. The difference in level between the height of the mould and that of the highest point of the subsided concrete
was measured.
viii. This difference in height in mm is the slump of the concrete.

4. Presentation of Results of Experiments

4.1. Test No.1-Compressive Strength and Slump Test of Sampled washed Aggregate Concrete Materials
(Specimen 1).
The technique adopted was to conduct laboratory tests which entailed preparation of concrete samples using coarse
aggregates obtained from selected quarry sites into available 150 mm square metal cube moulds. These cubes were
cured and. tested in the laboratory to determine their compressive strength. The measured compressive strength of

Journal of Scientific and Engineering Research

48
 Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

the specimen was calculated by dividing the maximum load (i.e. crushing-value) applied to the specimen during the
test by the cross - sectional area, calculated from the mean dimensions of the section and was expressed as N/mm2

Table 5 results indicate that concrete produced using the coarse aggregate obtained from Enugwu-ukwu, Awka,
Aguleri, Nsugbe , Ogbunka and Owelle-Ezukala has a compressive strength of 24N/mm', 19.5N/mm2,
25.77N/mm2, 20N/mm2, 29.33N/mm2 and 27.59N/mm2 respectively. The result implied that the concrete
produced using coarse aggregate obtained from the quarry sites at Ogbunka yielded a higher compressive
strength. Also the result of the slump connotes low workability since it is within the range of low workability
(i.e. 25-50%) except Nsugbe that falls within the class of very low workability.

4.2. Test No. 2-Sieve Analysis

Sieve sizes used for concrete aggregate as per -LS. 383-1970 are as follows:- 80mm, 63.0, 40mm, 20mm,
10mm and 4.75mm for grading of coarse aggregate, whereas 4.75mm, 2.36mm, 1.18mm, 600micro, 300rnicro
and 150micro are used for grading of fine aggregates. Or BS 812, Part-1, in U.K. this experiment was carried out
using a given quantity of dry coarse aggregate samples in each case from sampled specimen.

Table 5: Values of Compressive Strength Test and slumps test Results Obtained from washed Aggregate
Specimens
Location Sample Concrete Cube Weight. Slump Value Curing Crushing Compressive Strength
Specimen Mix (Kg) . Period Value (N/mm2)
Ratio (mm) (Days) (KN)

Enugwu- ukwu A 1:3:6 7.3 38 7 540 24

Aguleri B 1:3:6 7.3 39 7 580 25.77

Nsugbe C '1:3:6 7.2 21.5 7 450 20
Ogbunka D 1:3:6 7.1 40 7 660 29.33
Nkwelle- E 1:3:6 6.8 41 7 522.675 23.23
Ezunaka
Source: Researchers Field Work, (2014)

Table 6: Results on Sieve Analysis for Coarse Aggregate

Set of Weight Retained Percentage Retained (%) Percentage cumulative (%) Percentage Passing (%)
sieve Dia
(mm) A B C E A B C D E A B C DE A B C D P
38.10
31.75
25.40 100 100 100 I10.0 100
19.05 481.8 437.2 288.0 162 254.6 35.7 34.5 16.4 12.62 16.0 35.7 34.5 16.4 16.2 16.0 64.3 65.5 83:6 87:38 84.0
12.70 636.6 637.2 1440.8 972 1289.6 47.1 50.3 81.8 75.71 81.2 82.8 84.8 98.2 97.9 97.2 17.3 15.2 1.8 11.67 2.8

9,152 225.8 186.7 10.6 150 14.4 16,7 14.7 0.6 11.68 0.9 99.5 99.5 98.8 98.2 98.1 0.5 0.5 1.2 0.14
1.9
4.75
236
118
0.6
Source: Researchers field work (2014)

Journal of Scientific and Engineering Research

49
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

This was weighed before it was poured into the largest diameter size of sieve arranged in order of size with the
largest size, 80mm diameter on top followed by the next smaller size unto the smallest size, 4.75mm at the
bottom. Wet coarse aggregate specimen is oven-dried in the laboratory before utilization. The quantity
retained in each size category weighed and its percentage value was calculated against the total
volume/quantity measured. Below are the tabulated results:

From the result obtained in Table 6, the percentage passing for a single sized aggregate of nominal size 20mm
fall within 85-100 for sample C, D, and E. with sample A and B falling below 80%. All the samples fall below
20% for sieve diameter of 12.70mm and far the value also drop for sieve diameter of 9.52mm. However, the
gradation curve indicated the presence of insignificant quantity of coarse sand in the fine sand zone, large quantity of
fine in the gravel zone and some coarse aggregates higher than 20rnm diameter are present in the gravel zone
distribution. We concluded that Specimens were suitable for a 1:3:6 -20mm aggregate specification requirements
and thus fairly graded although it would provide good workability as shown in table 1.

5. Summary, Conclusion and Recommendation

5.1. Summary
The study evaluate the qualities of coarse aggregate used in concrete production in Anambra state especially
the one sourced within the state. In line with the set objectives the following were;
Firstly, in objective No.1 (i.e. establish qualities of good coarse aggregate, possible tests and
procedures), the researchers observed that properties of a coarse aggregate are grouped into 2:
Mechanical and physical properties. Key among them are strength; Absorption, -Porosity, and
Permeability; Surface Texture and Shape; Density and Specific Gravity, Aggregate Voids and
Undesirable Physical/Chemical Components (Deleterious substance). The researchers observed that compressive
strength of concrete can be as high as 150N/mm2 but the minimal is 21N/mm2. Based on classification high
strength, normal strength, and low strength concrete attains compressive strength of more 60N/mm2, 20-
60N/mm2 and below 20N/mm2 respectively at 28days. Also, grading requirements for coarse aggregate
concrete for 37.5mm max and 19mm max should consist 95-100% and 40-80% passing through 37.5mm sieve
and 19.5mm sieve respectively. Finally on objective NO 1, the researchers observed that slump below 50%
is rated low workability.
Secondly, in objective No 2, the researchers observed that there are many quarry sites in Anambra North but
few at both south and central. However, the samples for the study were collected at 3 towns in North (Aguleri,
Nsugbe and Nkwelle Ezunaka), Enugwu-ukwu (Central) and Ogbunka (South). The researchers found-out
that of all the quarry sites visited the breakings of stones were done with hands. Use of child labour is
prevalent in the entire quarry sites and finally roads leading to this quarry are not tarred.
Thirdly, or objectives No 3, samples collected were taken to laboratory for test. At the end of the test, the
following observations were made: Concrete produced using the coarse aggregate obtained from Ehugwu-
ukwu, Awka, Aguleri, Nsugbe , Ogbunka and Owelle izukala has a compressive strength of 2 N/mm 2,
19.5N/mm2, 25.77N/mm2, 20N/mm2, 29.33N/mm2 and 27.59N/mm2 respectively. Also th result of the
slump connotes low workability since it is within the range of low workability (i.e. 25- 50%) except Nsugbe
that falls within the class of very low workability. Finally, the percentage passing for a single sized
aggregate of nominal size 20mm fall within 85-100 for sample C, D, and E. with sample A and B falling
below 80%. All the samples fall below 20% for sieve diameter of 12.70mm and far the value also drop for
sieve diameter of 9,52mm

5.2. Conclusion
Based on the findings of the research the following conclusions were drawn:
 Except the concrete made with the Nsugbe samples others achieved the minimum compressive strength
of concrete (i.e. 21N/mm2) within 7 days.
 The crushing strengths/compressive strength attained by the samples fall within the normal strength
concrete (20-60N/mm2) within 7 days of age.

Journal of Scientific and Engineering Research

50
Ezeokonkwo JU et al Journal of Scientific and Engineering Research, 2015, 2(2):40-51

 The sample prepared with Ogbunka stone yielded-best compressive strength.

 Local stone if properly graded can compete favourably with granite chipping in term of strength
and other properties such as workability.
 Since the stones were break using hands but the use of machine would yield better the gradation of the
stones drastically.

5.3. Recommendation:
The study recommends the following:
 The key advantage that granite chippings have over local stone is that it is properly graded. Therefore,
the researchers recommend that stones should be properly graded-using machines rather than hand
breaking;
 Aggregate should be properly washed before using since most of them are coated with; impurities
and other clayey substances and muds which may hinder the process of bonding;
 Further study should be carry out using un-wash samples;
 Research should be extended to other quarry sites/towns not covered in the study;
Reference

1. Aker, D. J. (2000).. Building Materials. In Merritt F.S. (Deceased) Ricketts J.T. (Eds.), Building
Design and Construction Handbook (6th ed); pp. (4.1- 4.105), New York,McGraw-Hill
2. Anosike, N. M. (2011). Parameters for Good Site Concrete Production Management Practice in
Nigeria, (Doctoral thesis), Covenant University, Ota, Nigeria
3. Council of Registered Builders of Nigeria (CORBON) and Nigeria Institue of Building
(NIOB), d (2014). Improving the CorePractice Area for Builders IV, 7th MCPDP held at Abuja, Port-
harcourt, Gasau and Lagos, 20th — 23'd 2014.
4. Duggal, S. K. (2008). Building Materials (3'd edn), New Delhi, New Age International, (P)
Limited, Publishers.
5. Ezeokonkwo, J. U. (2014). Assessment of Quality Control of Concrete Production Works in the Hot
and Warm Humid Zone of South East Nigeria. Ph.D. Dissertation, Nnamdi Azikiwe University, Awka
Nigeria.
6. Monteiro, P. J. M., & Mehta, P. K. (1986). The transition zone between aggregate and type K
expansive cement. Cement and Concrete Research, 16(1), 111-114.
7. Okereke, R. A. (2003). Construction Materials Testing and Quality Control in Tropical Climate,
Owerri, Crown Publisher Limited.
8. Quironga, P. N., Fowler, D.W. (2003). The Effects of Aggregate Characteristics on the
Performance of Portland Cement Concrete, The University of Texas Austin, Texas, USA.
9. UNESCO-Nigeria Technical & Vocational Education Revitalisation Project-Phase II (2008). Science
and Properties of Materials , NATIONAL DIPLOMA IN CIVIL ENGINEERING
TECHNOLOGY
10. Reed, P., Schoonees, K., & Salmond, .J (2008). Historic concrete structures in New Zealand; Overview,
maintenance and management, New Zealand, Science & Technical Publishing

Journal of Scientific and Engineering Research

51