INSULATION GUARD FOR NON-GROUNDED AC NETWORKS KPM161x

• Direct connection up to 690V line voltage, up to 1.4kV with

HV adapter CH163/1,4

• Monitoring during both live and standby conditions

• For use in land, marine, offshore, sub-sea and ocean floor

installations

• Complies with IMCA D 045 Code of Practice

• ”Megger” - safe to 1.4kVDC when aux power is OFF

• Immune to earth capacitance and voltage surges

• Analogue output proportional to meter reading (F-version)

Specifications Application
Auxiliary Supply: 100-120, 200-240, 380-415 or The digitally controlled KPM161x series monitors insulation level between a non-grounded (IT)
440-460VAC, 40-70Hz (Fuse 0.5A) AC mains and its protective earth, regardless of whether the mains is live or non-live (standby).
Optional Voltage: 12-24, 48 or 110VDC (Fuse 2A) The unit is for land, marine, offshore, sub-sea and ocean floor use.
Supply tolerance: ± 10%
Power rating: 1,5VA
Contact rating: AC: 100VA - 250V/2A max.
An AC or DC auxiliary voltage is required for the unit, if powered from a separate source the network can
DC: 50W - 100V/1A max. also be monitored during standby conditions. Only ONE KPM161x can be connected to each IT-system.
Analogue Output: Up to 20mA, max 500R The ohmmeter and the triple-zone status LEDs give at a glance the clear safety message:
F-versions Up to 10V, min 100kohm
(other on request) - ALARM (red zone)
Temperature: -20 to +70ºC
- WARNING (yellow zone)
Weight: 0.85kgs
Front protection: IP52 (IP65 optional) - HEALTHY (green zone)

INTELLIGENT SETTING ASSISTANCE General

KPM161x has a built-in Assistance tool for setting/verification of
the trip levels and the analogue output. IDV MEASURING PRINCIPLE
Insulation is measured between the complete galvanically interconnected AC network and its protective
When either the Warning or Alarm potmeter on the rear is earth.
operated by user, the meter goes into Assistance Mode and
meter reading and analogue output will reflect the potmeter
setting (the blue LED will be lit in this mode).
The unit injects a DC voltage signal into the monitored system. The signal flows to ground via the path of
the insulation fault, the level of flow indicates the insulation resistance. The measuring accuracy is not
How to set alarm levels: influenced by any normal kind of load attached to theAC network.
Firstly adjust potmeter fully clockwise
(see that meter goes to the top), then Trip levels and delays are settable on unit rear. A trip LED flashes when the trip level is passed, the relay
adjust potmeter down to required
Warning or Alarm setpoint.
trips when the delay has elapsed. The timer resets if the fault is removed during countdown.

Without any movement of potmeters, MEGGER SAFE

the meter will revert to normal When auxiliary power is OFF the unit input is automatically protected against “megger” test voltages up
Insulation Monitoring Mode after to 1.4kVDC, and incorrect measurements caused by the unit’s input impedance are avoided.
approximately 10 seconds.
How to test analogue output signal: OUTPUTS
Adjust any trip level potmeter to activate Assistance Mode. All F versions have an isolated analogue output proportional to meter reading. If output is used for
Example: On a 4-20mA output, adjust potmeter fully anti remote meter reading, we recommend 0-1mA for the slave indicator.
clockwise for 4mAand fully clockwise for 20mA.
NOTE
The KPM161x range is designed to comply with specification IMCA D 045 Special versions of the KPM161x are available as:
“Code of Practice for the Safe Use of Electricity Under Water” issued by
IMCA.
KPM161xM series - Insulation Guards with DC detection function, protected against high-energy DC
The unit meets EN 61010-1 Cat. III, Pollution degree 2 and the relevant
environmental and EMC tests specified in EN 61326-2-4 to comply with
voltage imposed on the monitoredAC supply.
the requirements of the major Classification Societies.
KPM261x series - Insulation Guards with measuring loop continuity monitoring.

Norway
Denmark
United Kingdom Page: 1 of 4
REF: Datasheet.KPM161x - REV: 2.06/12.2018
www.megacon.com © All rights reserved to Megacon
ELECTRONIC CONTROL AND INSTRUMENTATION Megacon reserves the right to make any changes to the information at any time
 INSULATION GUARD FOR NON-GROUNDED AC NETWORKS KPM161x
Description Relay Operation

KPM161E2 & KPM161F - KPM161G & KPM161GF Scale range: 0-1000kΩ - (>6MΩ)
This unit is used for hospital, industrial, marine and offshore installations.
Warning Alarm Fail Safe Latch
R1 
Start of monitoring function is delayed when auxiliary power is switched on. (default 5 secs delay)  
R2 *
R3   *
The unit has minimum 150 mS detection time for any insulation fault.
Model Latch Output Fail Safe Adjustments Trip level Delay
KPM161E2 - - X WARNING: 0-1MΩ 0-30secs
Direct connection up to 690V line voltage. Up to 1,4kV via HV adaptor CH163/1,4. KPM161F - X X ALARM: 0-1MΩ 0,1-3secs
KPM161G* X - X
KPM161GF* X X X

Coloured sectors show

recommended areas of settings:
- Indicates alarm trip zone
- Indicates warning trip zone
- Indicates healthy zone

Output diagram Output table (example for 4-20mA) Range

25,00mA
Value (scale) mA output
20,00mA 0kΩ 20.00mA
10kΩ 15.22mA
15,00mA 20kΩ 12.32mA
30kΩ 10.61mA
10,00mA 50kΩ 8.68mA
100kΩ 6.69mA
5,00mA
300kΩ 4.98mA
0,00mA 1MΩ 4.28mA
10M(> 6M)
Open 1M 300k 100k 50k 30k 20k 10k 0k Open (>6MΩ) 4.00mA

Description Relay Operation

KPM161E3 & KPM161F3 - KPM161G3 & KPM161GF3 Scale range: 0-1000kΩ - (>6MΩ)
This unit is used for hospital, industrial, marine and offshore installations.
Warning Alarm Fail Safe Latch
R1 
Start of monitoring function is delayed when auxiliary power is switched on. (default 5 secs delay) R2  *
R3   *
The unit has minimum 150 mS detection time for any insulation fault.
Model Latch Output Fail Safe Adjustments Trip level Delay
KPM161E3 - - X WARNING: 0-10MΩ 0-30secs
Direct connection up to 690V line voltage. Up to 1,4kV via HV adaptor CH163/1,4. KPM161F3 - X X ALARM: 0-10MΩ 0,1-3secs
KPM161G3* X - X
KPM161GF3* X X X

Coloured sectors show

recommended areas of settings:
- Indicates alarm trip zone
- Indicates warning trip zone
- Indicates healthy zone

Output diagram Output table (example for 4-20mA) Range

25,00mA
Value (scale) mA output
20,00mA 0kΩ 20.00mA
10kΩ 15.22mA
15,00mA 20kΩ 12.32mA
30kΩ 10.61mA
10,00mA 50kΩ 8.68mA
100kΩ 6.69mA
5,00mA
300kΩ 4.98mA
0,00mA 1MΩ 4.28mA
10M(> 6M)
Open 1M 300k 100k 50k 30k 20k 10k 0k Open (>6MΩ) 4.00mA

The MEGACON policy is one of continuous improvement, consequently

equipment supplied may vary in detail from this publication.

Norway
Denmark
United Kingdom Page: 2 of 4

www.megacon.com Innovation Beyond Tradition

ELECTRONIC CONTROL AND INSTRUMENTATION Uniquely MEGACON, simpler it can't be!
 INSULATION GUARD FOR NON-GROUNDED AC NETWORKS KPM161x
Description Relay Operation
KPM161E2-SKK & KPM161F-SKK - KPM161G-SKK & KPM161GF-SKK Scale range: 0-1000kΩ - (>6MΩ)
These optional units are similar to KPM161E2 & KPM161F - KPM161G & KPM161GF.
Warning Alarm Fail Safe Latch
R1 
The only difference is that the delay before the start of monitoring function is shorter. (default 1 secs delay)
R2   *
R3   *
The unit has minimum 150 mS detection time for any insulation fault.
Model Latch Output Fail Safe Adjustments Trip level Delay
KPM161E2-SKK - - X WARNING: 0-1MΩ 0-30secs
Direct connection up to 690V line voltage. Up to 1,4kV via HV adaptor CH163/1,4. KPM161F-SKK - X X ALARM: 0-1MΩ 0,1-3secs
KPM161G-SKK* X - X
KPM161GF-SKK* X X X

Coloured sectors show

recommended areas of settings:
- Indicates alarm trip zone
- Indicates warning trip zone
- Indicates healthy zone

Output diagram Output table (example for 4-20mA) Range

25,00mA
Value (scale) mA output
20,00mA 0kΩ 20.00mA
10kΩ 15.22mA
15,00mA 20kΩ 12.32mA
30kΩ 10.61mA
10,00mA 50kΩ 8.68mA
100kΩ 6.69mA
5,00mA
300kΩ 4.98mA
0,00mA 1MΩ 4.28mA
10M(> 6M)
Open 1M 300k 100k 50k 30k 20k 10k 0k Open (>6MΩ) 4.00mA

High Voltage Adaptors up to 1,4kVAC for KPM161x series

- HV Adaptor for AC Insulation Guards
- CH163x series, up to 1400V Line Voltage live or non-live (standby)
- Creates safety barrier from live HT network to LV switchboard
- Limits measuring output signal to safe levels
- No restrictions on distance between adapter and LV switchboard

Voltage Adaptors CH163x series are used for Insulation Guard KPM161x when the monitored line voltage is higher than 690VAC. These adapters
are a passive low-pass filter for use in 50, 60 or 400Hz networks, and are potted in polyurethane.

These units includes high inductance reactance modules, connected in a special configuration to avoid DC saturation. Connection to the star-point
(Neutral) is Preferable. These adapters maintain a highAC suppression of its signal output to very low, safe levels, under all conditions.

Caution
Terminal 1 must be disconnected during ’’megger’’ test.

CH163/1,4 up to 1.4kVAC

The MEGACON policy is one of continuous improvement, consequently

equipment supplied may vary in detail from this publication.

Norway
Denmark
United Kingdom Page: 3 of 4

www.megacon.com Innovation Beyond Tradition

ELECTRONIC CONTROL AND INSTRUMENTATION Uniquely MEGACON, simpler it can't be!
 INSULATION GUARD FOR NON-GROUNDED AC NETWORKS KPM161x
+ -
Relays shown de-energised, ~ ~ Analogue Output
Reset
a fail-safe relay energises (only latching versions) KPM161F, KPM161GF, KPM161F3, KPM161GF3, KPM161F-SKK and KPM161GF-SKK
when unit is powered.
have an analogue output proportional to meter reading. (Special outputs are available on
9 KPM161x AC Aux Supply
(Standard) 1
request)
OR Add suffix from table below to type designation to specify output required:
10 R1 DC Aux Supply 2
(Optional 48 or 110VDC)
O/P1 0 - 10mA O/P6 N/A
11 O/P2 0 - 20mA O/P7 N/A
O/P3 4 - 20mA O/P8 0 - 10VDC
12 O/P4 N/A O/P9 N/A
Line / Neutral 4 O/P5 N/A O/P10 N/A
13 R2
NOTE:
14 See below
for correct
15 connection Reset / Parallelling Disable Function
16 R3
PE 6 KPM161x has a built-in disable function. When connecting two or more IT-networks together
17 only one unit can be active, the other(s) must be disabled. When unit is disabled the power
led will flash every 2 seconds to indicate that unit is inactive.
19 Reset / Disable
Use a potential free contact on terminal 19 and 21 to activate the disable function (after 2
+ 22 20 + secs). When activated the measuring input terminal 4 will be internally disconnected.
Analogue O/P DC Aux Supply
(Optional) (Optional 12-24VDC)
- 23 21 - A pulse (60mS-2 Sec) on terminal 19,21 will only reset any latching alarm.

Dimensions
9 1
10 2
11
12
13
4
DIN96
14
15
16 PANEL
17 CUTOUT
6
92 x 92mm
Mounting Bracket
19
22 20
23 21
Comport

92mm 99mm 1.25 to 8mm

115mm thick

NEUTRAL VOLTAGE INPUT LINE VOLTAGE INPUT

R (L1) R (L1)
S (L2) S (L2)
T (L3) T (L3)
N KPM161x * KPM161x
(< 690V) 4 (< 690V) 4
~/+ Aux. ~/+ Aux.
~/- Supply ~/- Supply
6 6
* To be connected
to any line voltage
N
*
CH163/1,4 (< 1,4kV) KPM161x CH163/1,4 (< 1,4kV) KPM161x
4 4
1 2 ~/+ Aux. 1 2 ~/+ Aux.
3 ~/- Supply 3 ~/- Supply
6 6

The MEGACON policy is one of continuous improvement, consequently

equipment supplied may vary in detail from this publication. ORDERING EXAMPLE:
Type: KPM161F
Aux. Supply: 200-240VAC
Network Voltage: 1,4kVAC
Analogue O/P: (O/P3) 4-20mA
Range: 0 - 10Mohm
Norway
Denmark
United Kingdom Page: 4 of 4

www.megacon.com Innovation Beyond Tradition

ELECTRONIC CONTROL AND INSTRUMENTATION Uniquely MEGACON, simpler it can't be!