JT-DPS6600

Signal generator and frequency counter

MAIN FEATURES
Display type TFT color LCD
Display size 2,4 Inch
Connection BCN Signal terminals
Features 2 channel Signal generator
1 channel frequency counter
Size 194 x 178 x 69 mm
Items delivered signal generator,
2x BNC signal terminals,
power supply

FURTHER SPECIFICATIONS
The JT-JDS6600 Signal generator
Signal waveforms Lorentz pulse, pulse, half-
and frequency meter can generate
wave, noise, exponential
signals up to 60 MHz in different
rise/ fall, CMOS, a. m. m.
waveforms and offers an outstanding
quality with its frequency counter. Frequency range:
The control panel with its buttons is sine 0 - 60 MHz
very intuitive. Further, the Menu can square, triangle 0 - 15 MHz
be displayed in German, English and PWM, CMOS, TTL, arbitrary 0 - 6 MHz
French language. Min. frequency resolution 0,01 µHz
Frequency accuracy ± 20 ppm
Frequency stability ± 1 ppm/ 3 hours
Load capability of the 150 mA max.
outputs
Operation temperature 0 - 40 °C
Operation humidity < 80 %

Published: 10.03.2021
JDS6600
Dual-Channel Signal Generator

1. GENERAL INFORMATION

Dear customer,

thank you for purchasing our product. In the following, we have listed what
you should consider during commissioning.

Should you encounter any unexpected problems during use, please do not
hesitate to contact us.
 2. DEVICE OVERVIEW

function rotary switch

2,4“ TFT LCD keys short cuts

on- / off Output

switch
Input

TTL-interface for
DC 5 V
PC-connection
USB-interface for
PC-connection
status of output
waveform channel
display

CH1 parameter

menu bar

CH2 parameter

difference of phase between CH1 and CH2

3. SHORTCUT-OVERVIEW

Configuration of wave form

WAVE

MEAS Configuration of measuring mode

MOD Activation of the modulation mode

SYS System settings

Control of the output from CH1 and CH2

OK - It is used in other menus as
control and confirmation (on / off)

Moving the position of the cursor

Selection of channel 1
CH1 - Hold down to set channel 1 as the main channel

Selection of channel 2
CH2 - Hold down to set channel 2 as the main channel

4. PARAMETER SETTINGS IN THE MAIN INTERFACE

Press OK to enable or disable simultaneously the output of both

channels.

Use the buttons CH1 and CH2 to switch between each channel.
By pressing it again while you are in one channel, you activate or
deactivate the according output. Hold down the accord-
ing channel button to place the channel in the main interface.

Press the WAVE button to activate the waveform. While the waveform is active,
the form can be changed quickly with the rotary button. The arrows keys can be
used to switch between the waveforms and the
presettings.

Use the multifunctional button 1 ( FREQ ) to highlight the frequency para­

meter. Then use the arrow keys to move the cursor to the value which should
be edited. Press the rotary button to edit the according value. Hold down the
multifunctional button to change the unit (μHz, mHz, Hz, KHz, MHz).
5. MEASURING AND COUNTING FUNCTION

Press the MEAS button and after that the multifunctional button FUNC
in the measuring mode to switch between the measuring function and the
counting function.

It can be measured the input frequency, period, positive pulse width, duty
cycle and other parameters. The measuring frequency range is between 1
Hz and 100 MHz. The measuring signal amplitude range is between 2 Vpp
and 20 Vpp. The input interface is ext. IN.

Coupling settings:

Press the multifunctional button COUP

to change between the AC and
the DC mode.

Gate time settings:

Press the multifunctional button GATE to set the gate time (0.01 - 10 S).
Move the cursor with the arrow keys to the value which should be edited.
Use the rotary button to adjust the value.

Measuring mode:

Press the multifunctional button MODE to change between the coun­

ting frequency and the counting period.

Measurement parameters:

Frequency, period, positive pulse width, negative pulse width, duty cycle

After you have set all parameters, you can use the multifunctional button
to start the counting function. The multifunctional button
can stop the function.

6. MODULATION MODE

Press the button MOD

to start the modulation mode. Press the
multifunctional button FUNC to switch between the sweep function
(channel CH1 / CH2), the pulse function (channel CH1) and the burst func­
tion (channel CH1).

Sweep function:
You can set any starting and ending frequency of the signal generator. The
possible time is between 0.1 and 999.9 s.

In the sweep mode, press the multifunctional buttons to

set the starting and ending frequency, as well as time, direction and mode.
After selecting the respective setting, the arrow keys and the rotary button
can be used for adjustment.
Pulse function:
With this option, it is possible to configure the pulse wave width and the
pulse time.

Press the multifunctional buttons within the pulse

function to select the pulse width, period, offset and amplitude. As soon as
a parameter is highlighted, you can adjust it with the arrow keys. The pulse
width and time can be set using the rotary button. You can switch between
ns and μs with the button OK .

Burst function:
The pulse sequence can be set on the output from 1 to108575 periods. The
burst mode is devided in internal CH2 channel bursts, external input bursts
and manual bursts. The time of a period from a burst is smaller than the
time of a period from a burst signal.

Press the multifunctional buttons within the burst

function (channel CH1) to select the pulse number and the burst mode.
The arrow keys can be used to set each parameter.

After all settings are adjusted, you can use the multifunctional button ON
to start each function and OFF to end it.

7. SYSTEM CONFIGURATION

Press the button SYS to open the setup menu. Use the
multifunctional buttons to navigate. The following
settings can be made:
Save & load, sound settings, configuration of brightness, language
settings, synchronization, setting of the arbitrary wave display

After you have opened the according setting, you can adjust them with
the rotary button. Press the multifunctional button SAVE to save the
according configuration.

Save & load:

In save & load you can save ( SAVE ) the adjusted values in data groups
(0 - 99) and if needed you can load them again on your device ( LOAD ).
You can clear data groups with the multifunctional button CLR .

Sound setting:
The sound can be activated or rather deactivated with the
multifunctional buttons ON and OFF.

Configuration of brightness:
You can adjust the brightness in 12 different levels.
Language settings:
The English, German and French languages are available.

Synchronization:
The channel CH1 is used as the target during the synchronization. The
parameters of the channel CH2 will change according to the parameters of
CH1. If the synchronization point is highlighted, presst the buttons
to select the point which has to be synchronized.

Use the multifunctional button ON to select and OFF to quit

the process.

Settings of the arbitrary wave display:

The amount of wave forms in the main interface can be adjusted via the
rotary button (1 - 60) very quickly.

8. PC SOFTWARE INSTALLATION

You can download the latest version of the PC software on our Website.

Start the installationby opening the file JDS6600.exe.

Press Next >> in the now opening window.

Next, enter the installation path and confirm with Next >>.

The selection of the modules to be installed must also be confirmed with

Next >>.
If you do not want the automatic search for updates enabled, you can now
disable it by unchecking the option. Then continue with Next >> again.

The system quick start introduced in Windows 8 occasionally causes problems

in connection with the installation and removal of new hardware and should
therefore be disabled. Confirm the deactivation with Next >>. Alternatively,
you can leave the system quick start enabled at your own risk. To do so, simply
uncheck the appropriate box.

The installation program now performs the corresponding installations.

After successful installation, you can exit the installer.
 9. USING THE SOFTWARE

You can connect the signal generator to your computer either with a USB cable
or with a USB-TTL cable.

Now start the JDS6600 software. Here you can first select the port where you
have connected the signal generator to your computer. If you are not sure which
COM port you have connected your signal generator to, open the Device Manager
and check the connection in the Connections tab (COM & LPT).

Then establish the connection with Connect.

In the Control Panel, which you can reach via the tab at the top of the
software, you can output the standard waveforms and function signals.
At Extend Function you will find the measuring, counting, burst, sweep and
pulse functions.

In Abitrary, you can create various custom waveforms and store up to 15 on

the device.
 10. FURTHER INFORMATION

Our information and redemption obligation according to the electro-law (ElektroG)

Symbol on electrial and electronic products :

This crossed-out bin means that electrical and electronic products do not
belong into the household waste. You must hand over your old appliance
to a registration office. Before you can hand over the old appliance, you
must remove used batteries and accumulators which are not enclosed by
2
the device.

Return options :
As the end user, you can hand over with the purchase of a new device
your old appliance (which has essentially the same functions as the new
one) free of charge for disposal. Small devices which do not have outer
dimensions greater than 25 cm can be submitted independently of the
purchase of a new product in normal household quantities.

Possibility of restitution at our company location during our opening

hours :

Possibility of restitution nearby :

We send you a parcel stamp with which you can send us your old appliance
free of charge. For this possibility, you must contact us via e-mail at
[email protected] or via telephone.

Information about packaging:

Please package your old appliance safe during transport. Should you not
have a suitable packaging material or you do not want to use your own
material, you can contact us and we will send you an appropriate package.

1
11. SUPPORT

If any questions remain open or problems arise after your purchase, we are
available by e-mail, telephone and with a ticket support system to answer
these.

Published: 06.01.2020