ifi*~226B~JU

';& It!ffl ~idlmf~ffl f*jfi3i M ~

Operation and Maintenance Manual of
Deutz 226B Series Generating Diesel Engine

.-.
---
--
WEICHAI
._,---""®
DEUTZ

~tJj~~mfR~~Mm:fI~&*1§1~ 1 Ii.~9"

WeiIang Weichai Deulz Diesel Engine Company Ltd - -

 Special attention

• In order to protect your legal interest, it is forbidden to dismantle the fuel pump lead seal op-
tionally
• If the injection pump were adjusted or lead seal were removed, the quality guarantee of the
company would become invalid immediately.
• We would not provide free service for the dismantled injection pump.
• Turbocharger rotor shaft is of precise part, forbid disassembling and colliding, Otherwise the
quality guarantees of the company will be of invalid.
• There are strict torques and tum angles for the main bearing bolts and connecting rod bolts,
Users don t loose and dismantle them, otherwise the quality guarantees of the company will he
of invalid.
• Before starting the engine, check coolant and oil whether they are filled up or not.
• Connecting rod bolt can t be reused.
• Meaning of identification:
• Exhaust gas contains noxious composition, therefore it must be discharged outdoors.
 Cautions

1. The engine has been tested strictly in accordance with the test stipulations in delivery. The
throttle has been sealed, it is forbidden to dismantle the seal optionally and to enlarge the throt-
tle. Otherwise we would not provide free service for returning product, replacement and repair,
users would better pay attention to this.
2. The engine operator must read this Opf..ration and Maintenance Manual carefully to know the en-
gines structure, and abide by the operation and routine rules in this manual.
3. During use new engine, a 50 hours runin must be carried through, during which period no over-
load operation is allowed.
4. Mter start cold engine, the speed should be increased slowly. It is forbidden to run the engine
in high speed suddenly and in idling for a long time. Mter removed the load, don t stop the en-
gine immediately and run the engine in idling for 5 - 10 minutes.
5. Mter stop the engine, if the ambient temperature is lower than oee and no antifreeze is used in
the coolant, the coolant in water tank and diesel engine should be drained off.
6. It is forbidden that the engine works without air filter and unfiltered air enters into the cylinder.
7. Applied fuel and lubricating oil must be accord with specified trademark and be filtered by
strainer, and the special clean container is used. The fuel should be settled more than 72
hours.
8. Assembly and maintenance of the engine must be done by specialized personnel.
9. The oil seal period of the engine is one year. Inspect the engine and adopt necessary measures
if beyond a year.
10. Rated power and power correction are in accordance with 1503046 - 1.
11. Its forbidden to smoke when filling fuel and / or oil.
 Contents

J>reface 1
Diesel engine photo 000000 000 000 000 00 • 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 • 0 0 000 0 0 0 000 0 0 0 000 000 00 0 000 000 0" 2

Diesel engine characteristic curve 0 0 0 • 0 0 0 0 0 0 0 0 •••• 0 0 0 0 0 0 • 0 • • • 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 • 0 0 0 0 • • 0 • 0 0 0 0 0 0 • 0 0 0 0 0 • 0 0 • • 0 • • 4

1 Main perfonnance and specifications .. 0 0 0 ••••• o. 00' • 0 0 0 0 0 0 0 0 0 • 0 00. 00 • • • 0 0 • 0 0 0 0 0 • • • 0 0 0 0 0 00 • • • 0 • • • • • • • •• 7

2 Specifications of main accessa.. ies 00000.00 •••• 00.0000000 •• 0 0 0 00000000. 0000000000000000000.000000000000. 8
Fuel system matching table 00 0 000 0 0 0 0 0 0 0 0 0 . 0 0 000 000 000 000 000 0 0 • 000 000 000 000 0 • 0 0 0 0 000 000 000 000 .00 0 • 0 • 0 0 10

3. Diesel engine construction 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 . 0 0 0 0 0 0 0 . 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 . 00 0 0 0 0 0 0 0 0 0 0 0 0 0 000 0 0 • 000 0 0 0 00. • • • 11

3. 1 Cross and longitudinal section view of diesel engine 000000000000000000000000000000000000.00.000.0 11

30 2 Cylinder block subassembly . 0 000000000000000000.00.00. 0 0 0 0000000000000000.0 • • 0 • • • 0000000 • • • • 00 • • 00. 13

3. 3 Crank shaft and connecting rod mechanism 000 000 0 0 0 000 00 0 000 000 000 000 000 0 0 • 000 000 0 • 0 0 0 0 • 0 0 000 000 16

3. 4 Gear train 0000 00 0 0 0 0 0 0 0 • • 000 000 000 000 000 000 .00 000 0 0 • 000 000 0 0 0 000 000 0 0 0 000 00 0 0 • 0 0 0 0 • • 0 .00 . 0 . 000 • 0 •• 0 0 • • • 19

3. 5 Cylinder head and valve system 0 • • • 00 • • • • 0 0 0 • • 0 0 0 . 0 0 0 0 0 0 0 0 0 0 0 0 . 0 . 0 0 0 0 . 0 . 0 0 . 0 • • 0 0 0 0 0 0 0 . 0 0 . 0 0 0 0 0 0 0 0 19

3. 6 Fuel supply system .0 ••• 00.000000 •• 00000000.000 •• 00.0000000.0000000000. 0 00000. 0 000000.000 •• 000.0.000000 22

3. 7 Lubricating system 0.00.000.00 ••• 00000. 0 00' .000000 •• 0000000000000000.000 •• 0.0.0.0000.00000.00000000000. 26

3. 8 Cooling system 0 • 0 0 0 • 000 000 0 • 0 0 • 0 00 0 0 0 0 0 0 0 . 0 0 o. 0 000 0 0 0 000 o ••• 0 0 0 0 0 000 00 • 0 0 0 00 • 0 0 0 0 0 0 0 0 • 00. 000000 000 0 o. 27

3. 9 Intake & exhaust system 000 0 • 0 0 0 0 0 0 0 0 •••• 0 • 0 0 • 0 • 0 • • 00 0 o ••• 0 0 0 0 0 .0. o ••• 00 0 • • 00 • • 00 • 0 0 • 0 • • • • • 0 0 000 .00 29

3. 10 Electrical system . 0 0 0 • 0 0 0 •• 0 0 •• 0 o. 0 • 0 0 0 0 • • 00 0 • 0 0.0000 00 0 0 0 • 0 • • 000 0 0 0 00 • • • • 0 • 0 000 00 0 • • 0 • • • 0 0 • • 00 0 0 0 000 31

3. 11 Main bolts tightening torque o. 0 0 0 0 0 0 0 .0 0 0 • 0 •• 0 0 0 0 000 000 .00 • 0 0 • • 0 000 0 • 0 0 ••• 0 0 • 0 0 00. 00 • • 00 000 000 0 0 0 34

4. Operating requirement and procedures .00 0 • 0 000 0 0 0 0 • 0 0 0 •• 0 0 o. 0 000 •• 0 000 0 • 0 0 • 0 0 • 0 0 0 0 00 • 000 000 000 . 0 . 36

4. 1 Rules on the working fluid and the auxiliary material 00 • • 00 000 0.0 000 • 0 • 00 0 • • 0 . 0 0 o •• 000 • • 0 0 • 0 .00 36

4. 2 swinging requirement 0000.0 • • 0 0 . 0 0 0 0 0 . 0 0 . 0 • • 00 • • • 0 0 0 . 0 . 0 0 0 0 0 0 0 0 0 0 0 . 0 0 . 0 0 . 0 0 0 0 0 . 0 0 0 . 0 0 • • • • • 0 0 0 0 . 0 0 0 0 0 0 . 39

4. 3 J>reparation before the start 0.0.000000 •• 0000000.0000000000000 •• 0 •• 000000 • • • 000.0 0 000 • • 0 • • • • 0 •• 00000. 39

4. 4 Start . 0 • 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 • 0 0 • 0 • 0 0 0 0 • 0 0 0 0 0 • 0 0 0 0 0 0 0 0 0 0 • 0 0 • 0 0 • 0 0 0 0 0 0 0
0
0 0 0 •••• 0 0 0 • 0 0 0 0 0 0 • 0 0 0 • 0 • 0 0 0 0 0 0 41

4.5 Speed regulating 0000000000000000.00 •• 0.000.00.000.0000 •• 0. 0 •• 00000000.0000000000000000.0 •••• 0000.000 ••• 42

4. 6 stopping the engine 00000.000 •• 000000000.0000.0.0.00000000.000000 • • • 0.0 •• 0000000 •• 0 00.00 •• 0 0 0 0 0 000000 42

4. 7 Operating environment 0 0 0 000 0 • 0 0 0 0 0 0 0 • 0 0 • • • 000 0 • 0 0 0 • 0 0 0 .00 0 0 0 000 000 0 • 0 000 00 0 000 0 0 0 000 00 • 0 • 0 0 0 0 • • • 00 0 43

5. Maintenance 000 000 0 0 0 0 0 0 .0 • 0 0 0 •• 0 0 • 0 .0 • 000 0 0 0 .00 0 0 0 • • 0 0 0 0 000 000 0 • • 000 • 0 0 0 • 0 .0 0 • • • 0000.0 000 000 0 0 0 .00 0 0 0 00' 44
5. 1 Time table for Maintenance ... 0 •• 0 0 •• 0 • 0 • 0 0 0 0 0 0 0 0 0 0 0 • 0 .0 • • 0 0 000 0 0 0 000 0 0 0 00 0 0 • 0 000 000 00 • 0000 0 0 0 • 0 000 44
5. 2 Maintenance procedure 0 00 0 • • 000 0 • 0 0 0 • 0 00 • 0 0 00 0 0 0 • 0 ••• 0 •• 0 • 0 • 0 000 0 •• 0 • • • • 0 00 • 0 0 ••••• 0 • 00 • 0 0 . 0 0 0 00 0 . 0 0 45

6. Trouble shooting 0 0 0 0 0 0 0 0 0 0 0 0 0 •••• 0 0 0 • 0 0 0 • 0 ••• 0 0 0 0 0 0 • 0 0 • 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 • 0 0 0 0 0 0 0 0 0 •• 0 50

Appendix 1: Relationship between crankshaft angle <I> and piston displacement S 00.000000000 51

Appendix 2 : Wear Limits of J>arts of the Engine 0.0000000000000000. 0 0 000000000000000000.00000 •• 0 0.0000 52

 Preface

2,26B series diesel engine is manufactured by Weifang Weichai Deuzt Diesel Engine Company Ltd ( composed of
Weifang Diesel Engine Works and Germany Deutz Company).
According to intake mode, 226B series diesel engine is divided into natural aspirating, turbo - charging, turbo-
charging and inter - cooling type. With 3, 4 and 6 cylinders, it is a high - speed, 4 - stroke, water - cooled, in
- line and direct - injection engine. It has advantages of reliable and economical in working, advanced technical
data, low emission, good low - temperature start, simple operation and convenient maintenance. The speed
range is 1500r/min -1800r/min and power range is 30 -135kW. The symbols in each type of engine represent
the following meanings:

T B D 2 26 B 6 - D- X
I
Serial No.
.. I Generator model
I
1...-
I Cylinder number 6
' - - - - - - - Wet liner
No of cylinder line
Water cooled:2
1...- Nat u r a 1 asp ira tin g
1...- In t e r - coole d : B
L.- T u r b 0 - Gh a r g ed :T

Nameplate is fitted on the engine in delivery, model, design number, power, speed, serial number, manufactur-
er, address, manufacturing date and weight are marked on the nameplate. Each design number corresponds to
certain engine, each model may has several design numbers. The serial number is marked on the cylinder block
3.Ild located under the oil filter seat.
This manual introduces the main technical data, construction features, operation and maintenance methods and
inspection points of 226 B series diesel engine. it applies to al the generator engine model for the customers.
In order to make 226B series diesel engine provide better service for you, its better for users to know the basic to
refer to structures and the engine operating methods so as to play its active role.
With the development of the production technology, the construction, accessories and performance parameters of
226B engine will be improved gradually. The product in the manual may be slightly different from the supplied
one, pay attention to the supplementary manual. It is subjected to change without notice.

1
 2

13 12 11 10

6-cylinder diesel engine

Thermostat 2 Water pump 3 Air clearer 4 Intake manifold(only for intercooled engine)
5 Heat shield for turbocharger 6 Exhaust pipe frock 7 Inection pump and governor
8 Oil dipstick 9 Fuel supply pump 10 Fuel filter 11 Oil filler 12 guard shield
13 Warer tank
Remark:The counter parts of number 5, 6, 12 are not equipped on general gen-engine, However,
they are compositiions of CE-certifitated models.
 2 3 4

11 10 9 8 7 6 5

4-cylinder diesel engine

Warer tank 2 Air clearer 3 Turbocharger 4 Heat shield for turbocharger

5 Exhaust pipe frock( Only for turbocharged engine) 6 Inection pump and governor
7 Oil dipstick 8 Fuel filter 9 Fuel supply pump 10 Oil filler 11 guard shield
Remark:The counter parts of number 4, 5, 11 are not equipped on general gen-engine,However,
they are compositiions of CE-certificated models.
 D226B-3D load rated power 30kW(no fan)
Gf(kg/h) characreristic curve rated speed 1500r/min be(g/kW.h)
8 270

6 250

4 230

2 210
10 15 20 25 30 35
P(kW)

TD226B-3D load speed rated power 45kW(no fan)

Gf(kg/h) characreristic curve rated speed 1500r/min be(g/kW.h)
14 300

280

10
260

240
6

220

2 200
o 10 20 30 40 50 60
P(kW)

4
 TD226B-4D load rated power 60kW(no fan)
Gf(kg/h) characreristic curVE} rated speed 1500r/min be(g/kW.h)
18 370
350
14 330
310
10 290
270
6 250
230
2 210
o 10 20 30 40 50 60 70
P(kW)

TD226B-6D load rated power 90kW(no fan)

Gf(kg/h) characreristic curve rated speed 1500r/min be(g/kW.h)
24 300

20 280

16 260

12 240

8 220

4 200
o 20 40 60 80 100 120
P(kW

5
 TBD226B-6D load rated power °120k W(no fan)
Gf(kg/h) characreristic curve rated speed 1500r Imin be(g/kW.h)
30 240

20 220

10 200

o 180
o 20 40 60 80 100 120 140
P(kW)

TBD226B-6D5 load rated power 132kW(no fan)

Gf(kg/h) characreristic curve rated speed 1500rImin be(g/kW.h
40 240

30

20 220

10

o 200
o , 20 40 60 80 100 120 140 160
P(kW)

6
 1"Main performance and specifications
D226B -3D D226B -4D TD226B -3D TD226B -4D TD226B -6D TBD226B -6D TBD226B -6D5
Item
No. of cylindr 3 4 3 4 6 6 6
Borelstroke (mm) 105/120
Displacement (L) 3.117 4.156 3.117 4.156 6.234 6.234 6.234
Type 4. - stroke, water - cooled, in line, DI ,wet liner
Rated power (kW) 30 40 45 60 90 120 132
Rated speed rl min 1500 1500 1500 1500 1500 1500 15Qll
110% of rated power (kW) 33 44 49.5 66 99 132 145
Speed at 110% of rated power
1500 1500 1500 1500 1500 1500 1500
( rfmin)
Mean effective pressure at rated
770 770 1155 1155 1155 1534 1687
conditions (kPa)
Mean piston speed (m1 s ) 6 6 6 6 6 6 6
Compression ratio 16.4 15.5
3000 3000 2700
Cold compression pressure (kPa) (Min 25(0) (Min 25(0) (Min 22(0)
Min idle speed (r/min) 800 :1:50 800 :1:50 800 :1:50 800 :1:50 800 :1:50 800 :1:50 800 :1:50.
-J
Steady governing speed ~5

Natural
Aspiration aspiraed
Turbocharged Turbocharged and inter - coded

Firing order 1 -3-2 1 -3 -4-2 1 -3-2 1 -3 -4 -2 1 -5 -3 -6 -2-4

Oil capacity( sump) (L) 7.25 9 7.25 9 13 13 13
Oil pressure (kPa) 300 -550
Oil pressure at idle (kPa) ;;,100
Max permitted oil temp ( 'C) ~120

Max permitted water outlet temp ( 'C ) ~90

Exhaust temp after turbine ( 'C ) ~600 ~600 ~550 ;,;;550 ~550 :ii550 ~550

Starting method Electric

Permitted gradient longitudinallCI'088 25130 30/40 25130 30/40 20/45 2(}/45 20145
Crankshaft rotation (from freeend) Clockwise
Noise dB(A) =E;110 =E;110 =E;110 =E;110 =E;110 =E;110 =E;110
Weight (kg) 520 560 530 570 760 780 780
For the models that are egaipped with elecfronic governor, the governipg speed is no more than 1. S
Steady governing speed Refer to electronic governing instruction
All of the models above can be installed with electronic governor.
 2" Specifications of main accessories

No. Name

~ Item

Type
D226B -3D D226B -4D TD226B -3D

Multi - cylinder integrcoted type BQ or type A

TD226B -4D TD226B -6D TBD226B -6D

Multi - cylinder integrated type AD or A

TBD226B -6D5

Injection Model See" Fuel system matching table"

1 pump Rated speed ( r/min)
3
750 I 750
Rated fuel delivery ( mm /cyc) 61 81 88 87 83 106 HI
Type Mechanical and centrifugal
2 Governor
Model See" Fuel system matching table"

Fuel feed Type Plunger type

3 pump Model See" Fuel system matching table"
Type Multi - hole, valve needle
Part No. 12270162 12270162 12153057 12270162 12153057
4 Injector
Open pressure See" Fuel system matching table"
00
Nozzle Model See" Fuel system matching table"

Fuel Type Spiral paper element

5 filter Part No. 12270392 . 13020488
Type Centrifugal (scroll case is on the middle plate)

Water Part No. 12273212 12159770 1273240

6 pump Impeller diamcter( mm) 4>86 4>HO
Rated speed ( r/min) 3000 2210
Type Gear type
7
Oil Part No.
pump 12166769 12166779 12166769 12166779 121559765
Rated speed ( r/min) 1700
Type - - - Rubber type Silicon - oil type
Crankshaft
8 damper Part No. - - - 12160595 12272805
Outer diameter( mm) - - - 4>182- 4>3 10
Type - Radial
9 TurhochaIt.er
Model - - K14orSJ50 K240rJ60S - 2 n6 DorS2B7623 HHO. 85D9orK27
 Specifications of main accessories ( 2 )

No.

10
Name

Oil
~ Type
D226B -3D 0226B -4D T02268 -3D TD226B -4D

Spiral paper element

T0226B -6D TB0226B -6D TBD226B - 6D5

filter 12272453 01174421

Part No.

Oil Type Round plate type

11 cooler

Type Wax type

12 Thermostat Opentemperature('C) 75
/
Full open temperature( 'C ) 90

Type DC, selfexcitation

\0 13 Starter Power 4kW

Voltage 24V(12V is optional)

Type Three - phase AC, commutated and voltage regulated

Part No. 12903819 13020748

14 Generator
Power 0.75kW

Voltage!current 28V127A(14V is optional)

15 Intercooler Type - - - - Air - oiv intercooled Air - oiv intercooled Air - oil' intercooled

Air cooled and Air cooled and Air cooled and Air cooled and Air cooled and Air cooled and Air cooled and
Type finand tube type finand tube type finand tube type finand tube type finand tube type finand tube type finand tube type
Water
16 cooler Model ( or part No. ) 13025078 13025078 13025078 13025078 13024933 13024933 13024933
2
Radiation area (m ) 20 20 20 20 30 40 40
Type Exhaust Exhaust Exhaust Exhaust Exhaust Exhaust Exhaust
17 Fan Part No. 13021367 13020367 13021367 13021367 13021535 13021190 13021190
Outer dia( mm) ~6 ~ ~ ~ cf>54O clJ600 clJ600
Fuel System Matching Table

Diesel engine Model TBD226B -6D TD226B -6D TD226B -4D D226B -3D TD226B -3D TBD226B -6D5

Injection pump assembly no. 13020436 13021799 13021656 13021938 13022109 13023574

CPES6AD100 CDES6ADlOO CPES4AD95 BH3QT80R9 BH3QT85R9

Injection pump model BP1213
D320RS2139 D320RS2140 D320RS2152 BH3A95R504 BH3A95R501

CRSV450... CRSV450... CRSV450...

1'300 -750Z TI00-750Z +TRSUV
Governor model
750ADOC139R 750ADOC139R 750ADOC139R msv330 - 750A504 'mSV33O -750A501 4500 -750P

ESG 2000 ESG2000

Electronic governor model
(I2V,24Vare optional)
ESGI500Cl - D ESGIoooC1

SVHZ2204 SVHZ2204
Supply pump model SAD/H2206 SAD/H2206 SAD/H2206 5505
SAlH2208 SAlH2208

Fuel delivery advance anggle 16 ±0.5 18 ±0.5 18 ±0.5 20.5 ±0.5 20.5 ±0.5 14 ±O. 5

Injector number 12153057 12153057 12270162 12270162 12153057 12153057

Injector body model KBEL90S3/13 KBEL90S3/13 KBEL90S3/13 KBEL90S3/13 KBEL90S3/13 KBEL90S3/13

InjectIon nozzle model DLLA151S972 DLLA151S972 DLLA152S1l80 DLLA152S1180 DLLA151S972 DLLA151S972

Injection pressure (MPa) 22 +0••

High - pressure Cuter dia • inrer

6.1. 75
pipe dia{mm)

10
3. Diesel engine construction

3. 1Cross and longitudinal section view of diesel engine

3.1.1 Longitudinal section view of D226B -4 diesel engine

13 14 15 16 17 18

10

8----t

II-++-+---t+-+-- 22
7---~tt¥:~~~~
6----~ 23

,~--24

5 4 3 2 1

1 Oil sump 2 Two - stage balancing mechanism 3 Pre - filter 4 Oil pipe 5 Oil dipstick
6 Gear case cover 7 Oil pump 8 Crankshaft belt pulley 9 Speed sensor (on the flywheel housing)
10Fan 11 Inspirator 12 Water pump 13 Cylinder head 14 Rocker arm and rocker arm support
15 Cylinder head cover 16 Water outlet pipe 17 Intake valve 18 Exhaust valve
19 Piston 20 Cylinder liner 21 Connecting rod 22 Rear oil seal cover 23 Flywheel
24 Flywheel housing

11
3.1.2 Cross section view of D226B -4 diesel engine

17 18 19 20
I

16 - - - - _ _ _ + _
- " I ! = - - - - - - - 21
15----F-
~------22

14 ------l~-___=+~.t"rn~..,.,~~
~~~\-~--tt------- 23
13--------k"
12-----....
11----- If t - - - + l i H - + + - - - - - - 24
10-----"....:~---W

9 ---::~=_fI4---,.._r~1f';1

8-----'-oo~-r

7---r---1'n,;;\i
~~~ /<:JT--25
6----- /

5-----~

4 -------;--'1-\

3-------~~'-­
27
2--------

1--------~ ~-----28
\......::::=-.+----.;;;::::.:..JJt::i

1 Oil sump 2 Pre - filter 3 Two - stage balancing mechanism 4 Cylinder block
5 Crankshaft 6 Engine stop lever 7 Camshaft 8 Fuel supply pump (or piston pump)
9 Oil pipe( to injection pump) 10 Oil filler (various position) 11 Tappet 12 Injection pump and governor
13 High - pressure pipe 14 Push rod "15 Exhaust pipe 16 Intake pipe
17 Rocker ann 18 Cylinder head cover 19 Water outlet pipe 20 Intake/exhaust valve
21 Injection pump 22 Cylinder head 23 Piston 24 Connecting rod 25 Oil dipstick
26 Oil filter 27 Safety valve 28 Oil drain plug

Note: For 3 - cylinder and 6 - cylinder engine, there is no two - stage balancing mechanism.

12
30 2 CyJ.inder block subassembly
Cylinder hlock suhassemhly mainly consists of cylinder hlock, liner, gear case, rear oil seal cover, flywheel
housing and oil sump.

2 3 4

D
5
(£1
ctJl

A B

1 Gear case (front cover) 2 Cylinder hlock 3 Cylinder liner

4 Flywheel housing 5 Rear oil seal cover 6 Main bearing cap
7 Oil sump 8 Seal strip 9 Seal plate

When A structure is adopted, coat seal glue on D joint face; When B structure is adopted, coat seal glue on
both D and E joint face.
Fig 1

Cylinder hlock is made of high - strength cast iron, it has good strength and rigidity. For 3,4 and 6 - cylin-
13
der engine, cylinder block has 4, 5 and 7 main bearings separately. The thrust ring is fitted on the first main
bearing (flywheel end). The main bearing cap is tightened by MI4 -10.9, the torque is about 70Nm and
then t"e cap is turned for 90: Tightening order is shown in fig 2. First tighten the main bearing in middle,
then tighten the bearing on both ends. For camshaft hearing holes in cylinder block, only the last one (free
end) is fitted with bronze camshaft bushing. There are two holes in the bushing, one of them is aimed at the
oil hole in cylinder block in mounting, another one should be upwards. (shown in fig 3). For turbocharged
engine and turbocharged and inter - cooled engine, a jet per cylinder is mounted on the right of cylinder
block (~ewed from flywheel end) for cooling piston.

Fig 2

Camshaft bearingl

"'XA~:i'~:-'\
r: "'<~> '" """.,,"
'"

l,
I>"", "'"
\\ " ' '. v1'" ~
"',.,.,.,....""
I

>-[--~~
.~........... ---- 1 _

Fig 3 Fig 4

226B series diesel engine adopts wet cylinder liner. In order to guarantee sealing after assembling, there are
two rubber seal rings on the upper and lower locating positions of the liner respectively. The lower seal ring
is set up in the seal groove on cyHnder block and the upper one is set up in the seal groove on the upper end
14
of cylinder liner.
Before mounting, coat some lubricate grease on the seal rings (Fig. 4).

The front end and rear end of cylinder block are connected with gearbox cover and rear oil seal cover and fly-
wheel respectively. When mounting, coat some Loctite 5910 (or other alternatires of -the same charas teris-
tic) sealant on the contact surfaces of gear case cover, rear oil seal cover and cylinder block. The tighten
force for gear housing bolts (M8 - 8.8) is about 20 - 25Nm.

There are SAEI ,SAE2,SAE3 and 135C flywheel casings are available for different engines and applications.
There is a observation window on the top or the bottom of flywheel casing (fig. 5) for viewing the graduation
on flywheel and defining the TDC and adjusting the fuel supply advance angle of injection pump. The fly-
wheel is fastened on cylinder block with MI0 - 12. 9 (tighten force: 80 + 5Nm) and M12 - 12. 9 bolts
(tighten force: 140 + 5Nm).

Fig 5
Oil sump has two stru ctunil forms: cast and steel - punched. The connecting positions of oil sump and cylin-
der block, gear case cover and lower bottom surface of rear seal cover are coated with Lotite 5910. It is
tightened through M8 - 8.8 bolts. Dust proof Flate is fitted between oil sump and flywheel housing. For fly-
wheel with hydraulic converter, because there is oil leakage of hydraulic converter, the flywheel sealing must
be guaranteed. So the joint surface between oil sump and flywheel is sealed by sealing plate and coated with
sealing glue. (fig 1 ) .

15
303 Crank shaft and connecting rod mechanism
Crank shaft and connecting rod mechanism consists of crankshaft, flywheel, piston, connecting rod, vibra-
tion damper, two - stage balancing mechanism { for 4 - cylinder engine only) etc.
Crankshaft:
Crankshaft is forged part, the balancing block is fitted on the crank arm and it is dynamic tested. Timing
gear is fitted on the front end of crankshaft, tight fit is adopted. In mounting, timing gear is heated to 250CC
and it is aimed at the crankshaft dowel pin. Hub is fitted on the front of gear, and it is tightened through
MI6 -10.9 bolts, the force is 240 + 10Nm or MI6 -12.9 bolts are adopted and the force is 300 + IONm.
Crankshaft front oil seal is mounted between gear case and hub, in mounting, lubricating grease is coated on
the positioning face. Another method of connecting timing gear case and crankshaft is pressed by hub direct-
ly.

Vibration damper: Vibration damper and pulley are fitted on the hub which is on the front end of the
crankshaft, they are tightened through MI0 * 8. 8 bolts, the force is 45 + 5Nm. While MIO -10.9 bolts are
adopted, the force is 65 + 5Nm. For 6 - cylinder engine, silicon oil damper is adopted, the diameter is
310mm (for engine speed 1500r/min -18oor/min). 4 - cylinder turbocharged engine adopts rubber damper
cast into integral with hub.

Flywheel:
Flywheel is fitted on the rear end of crankshaft, it is tightened by 6 M16 - 10.9 bolts. Pre - tightened by
70Nm and turned for 90°. Different types of flywheel can be adopted according to different matching applica-
tion and connecting method. On the flywheel, scale plate is stick to the side connecting surface of flywheel
and crankshaft. (fig 6) , the mark OT is the TDC mark of 1st and 6th cylinder. For some models, OT top
dead center mark and scale is marked on the flywheel circumference, and the inspection window is left on
the flywheel side surface.

Fig 6
16
Two - stage balancing mechanism:
In order to balance the two - order reciprocating inertia force of piston and connecting rod subassembly of 4
- cylinder engine and decrease the vibration, two - stage balancing mechanism is adopted. Drive gear ring
(1) of transmitting two - stage balancing mechanism is mounted on the crank arm, it should be heated to
250CC in mounting. "0 - 0" mark on gear should be marked on the specified position (fig 7). The mark tI

1" on the balancing shaft gear (2) of two - stage balancing transmitting mechanism should be matched with
the mark "1 - 1" on gear (3). Two - stage balancing mechanism is mounted on the main bearing cap, in
mounting, the mark "0 - 0" on gear ring should be matched with the mark on gear (2) of the balancing
shaft. The gear side clearance is O. 2mm and can be adjusted by gasket (fig 8). Oil circuit should be unob-
structed in mounting so as to ensure the lubrication of two - stage balancing mechanism bearing.

Piston group:
It consists of piston, piston ring , piston pin and lock ring.
For turbocharged and non - turbocharged diesel engine, the piston, piston ring and piston pin are dif-
ferent from each other.

Crankshaft

Main bearing cap

Gear ring Adjusting gasker

3 Driving gear
2

Fig 7 Fig 8

Combustion chamber and piston pin hole are off the piston center, mount the piston according to the right di-
rection. (Fig. 9)
There are three piston rings on the piston. The first ring is of a ladder ring, and the second ring is of cone
ring. The face with "TOP" (or factory mark) must be upwards (towards to the piston top) when mounting
(Fig. 10). The third ring is of a oil ring with a spiral spring. When mounting, the splits of three rings must
be staggered by a angle of 120°from each other, and the angle from the split of first ring to the edge of pin
hole must not less than 30°.
When mounting, coat some clean oil on the surlace of piston and cylinder liner.

17
Connecting rod: made through mould forging, composed of c(lnnecting rod body, connecting rod cover,
small end bushing and connecting rod blot. The big end is 45 °sectioned and the mating face is located with
6QOtooth. There are two connecting rod bolts (M14 x 1. 5 -12.9). When mounting, tighten them with
torque of 30Nm, and then turn 60 0 0nce more.
Caution: The connecting rod bolt can be used only once, or the potential fracture of the bolt may canse the
damage of the machine and personnel casualty.
The connecting rod body is machined with the cover, and they are not interchangeable. There are mating
marks on the body and cover. (Fig. 9)
Connecting rod bearing shell: this bearing shell is made of lead - copper with steel back. The alloy surface
is plateu with three - part alloy. For strengthened engine (e. g. the engine models of 120kW/15OOr/min
and 132kW/1500 for power generation) , the upper shell is of "quad - alloy - plated layer" with bigger load
bearing and anti - fatigue capabilities.
The connecting rod bearing shell is located with a elastic cylindricalpin pin.
Main bearing shell: this bearing shell is made of lead - copper with steel back. The alloy sunace is plated
,vith ternary alloy. There are oil grooves on the upper half of bearing shell. The main bearing shell is located
with spring pin. The lower half of this shell is of " quad - alloy - plated ( optional)" and is corresponding
with the connecting rod quad alloy plating, which is mainly applied in high power engine.

The face with "TOP" upwards

The face with "TOP" upwards

- -
.
@) I --

• 1
I

Fig 9 Fig 10

18
3.4 Gear train

Injection pump gear

Camshaft timing
2=68 2=45

Crankshaft gear
2=30
2=34

Fig. 11

8l
When the 1 cylinder piston is at TDC, the mark" 0" on the teeth of crankshaft gear is corresponding to the
"0 - 0" mark on two tooth of camshaft gear, and the mark" 0" on injection pump drive gear is correspond-
ing to the mark "0 - 0" on injection pump gear (see fig. 11). Camshaft gear is fastened on the camshaft
with four MI0 x 1. 25 - 10. 9 bolts, and the four screw holes are uneven distributed for easy aligning of
marks on the cam and the gear. The tightening force of these bolts are 85 +5Nm. Injection pump drive gear
is connected with camshaft gear by four M8 - 12. 9 bolts, and the tightening force is 85 + 5Nm. Injection
pump drive gear and camshaft gear can be moved relatively. If the injection advance angle cant be reached
by adjusting the injection pump, change the relative position of the two gears.

3. 5 Cylinder head and valve system

Cylinder head: made of alloy cast iron, one cylinder one head (with one intake valve and one exhaust
valve). The intake!exhaust ports are at the same side of the head. There is a seat ring on the intake!exhaust
port respectively. For turbocharged engine, the intake valve seat cone angle is 120 0 , and the exhaust valve
seat cone angle is 90° (fig. 12) . For natural aspiration engine, the intake/exhaust valve seat cone angles are
all 90 0 ( fig. 13) .
The width of valve seat face: 2.0 -2. 7mm (intake valve seat of turbocharged engine)
1. 4 - 2. Omm (other valve seat)
The injector is at the opposite side of intake/exhaust ports and forms an angle of 65°with the bottom face of
cylinder head. There are two water outlet ports available. One is on the top face of cylinder head and the
other is at the intake/exhaust port flange. The relationship of cylinder heads and diesel engines are as fol-
19
lows:
Cylinder head Water outlet Intake valve
Diesel engine structure
part No. position cone angle
Top face of cylinder Natural aspiration, air intake pipe and wa- -;
12212203 90 0
head ter outlet pipe are all separate parts
Top face of cylinder Turbocharged, air intake pipe and water
12214114 120 0
head outlet pipe are integral cast
Intake/exhaust port Natural aspiration, air intake pipe and wa-
12214~78 90 0
flange ter outlet pipe are integral cast
Intake/exhaust port Turbocharged, air intake pipe and water
12214132 120 0
flange outle"~ pipe are all separate parts

Valve seat/valve guide TD/TBD226B Valve seat/valve guide D226B

Seal ring

1.4-2.0

Fig. 12 Fig. 13

Valve guide: made of phosphor cast iron, and phosphate coating. Intake valve guide length is 58 mm, ex-
haust valve guide length is 51. 5mm. Mounting position of valve guides are shown in fig 12 and fig 13. There
are grooves and a rubber seal ring on the inner wall of guide to prevent oil from entering into cylinder.

Valve system: composed- of camshaft, tappet, push rod, rock ann, rock arm bracket, valve, valve spring
and some accessories.

Oil passage of valve system is shown in fig 14.

The oil came from cylinder block enters into tappet and the spherical surface of push rod through the ring
grOC1r~ on the tappet, and then into the hollow push rod, the rocker arm adjusting screw, the rocker arm and
arm shaft to lubricate the friction surfaces of rocker ann and valve.
20
Cold clearance of valve:
Inlet valve clearance: 0.2mm; exhaust valve clearance: 0.3mm.

Valve timing when the valve clearance is imm, Acceptable clearanle:

±3°.
Intake valve open: 0045'CA after IDC
Intake valve close: 8°15'CA after BDC
Exhaust valve open: 32°45' CA before BDC
Exhaust valve close: 0°15 'CA before TDC

Coat some clean oil on the sunace of camshaft hole in cylinder block before mounting the camshaft. The fan-
like stop plate for camshaft should be mounted. The stop plate is fixed with two M8 -12.9 blots, it'tighte-
ning force is 55 + 5Nm.

When mounting, coat some oil on the surfaces of rocker arm and rocker arm shaft. Rocker arm bracket is
fixed with MI0 - 8.8 bolt, tightening force is 40 + 5Nm. Lock up the rocker arm adjusting screw (M9 xl)
with a nut by force of 20 + 5 Nm.

Oil inlet
•

Fig. 14

Valve: The valves for turbocharged and natural aspiration engines are made of different materials, they can
not be used interchangeably. For turbocharged engine, the valve rod and valve head are made of different
materials. All valve rods are chrome plated. Mter the valve is assembled on the cylinder head, the valve
sinkage is about 1. 03 - 1. 42mm.
21
Mter cylinder heads are mounted on cylinder block, all intake/exhaust flanges must be on one plane to en-
&'~re the sealing of intake/exhaust manifold. Cylinder heads is fixed with four.Ml4 ':'12.9 bolts coated with
oil (I.llolybdenum disulfide is not Pennissible). The bolts should be tightened according to the sequence in
Fig 15 by 3 times. First, tighten up with a force of 30Nm, then turn the nuts through an angle of 120 0 , and
0
then turn the nuts through another angle of 120 •

Caution: The cylinder head bolt will be elongated by 0.2 - O. 6mm. If !be length from the end of the bolt to
the support face is up to 160.5mm, the bolt must be changed.

Fig. 15
3.6 Fuel supply system
Fuel supply system is composed of injection pump, governor, fuel supply pump, fuel filter, injector, high
pressure pipe, low pressure pipe and some accessories. (Fig. 16)

Injection pump and governor assembly:

Generally, injection pump, governor and fuel supply pump fall into one assembly. 226B diesel engine a-
dopts type AD and P Bosch injection pump and type RSV governor, some other types of injection pumps and
governors are also adopted (see "Fuel system matching table" ) .

There is a mounting flange on the end face of injection pump and there is an 0 - ring on the end face stop.
The injection pump is fixed with 4 studs, and tightening force is 35 + 5Nm. When mounting of injection
pump gear, the mark" 0" on injection pump gear should be faced with the "0 - 0" mark on the drive gear
for injection pump (fig. 11).

22
Fig. 16

23
Check and adjusting for delivery beginning.
Correct delivery beginning can enable the· engine to obtain good
pertonnsnce. The crankshaft angle can be detennined by meas-
uring the displacement which the piston from TDC, also it can
be done by making use of the flywheel mark. It is recommen-
ded to use the fonner method for more precision.
When determining with the piston displacement,
you should:
( 1 ) Turn the crankshaft to let the piston of cylinder next
to the gearcase end at TDC position of compression stroke (the
intake & exhaust valves are all closed).
( 2) Dismantle the rocker seat.
( 3) Dismantle the valve spring of intake valve or exhaust
valve. The valve head falls on the piston in the meantime.
(4) Set the dial gauge 1 with clamp at the top of valve
stem. (see Fig. 17)
( 5 ) Turn the crankshaft along CW and CCW directions to
measure the position of piston at TDC, and dial the hand of di-
al gauge to 0 graduation.
( 6 ) Turn the crankshaft along the contrary direction to its
working direction, and let the valve drop to not more than
15mm.
(7) Pull control handle 4 to the middle position. (see
Fig. 18)
( 8 ) Dismantle the delivery valve 5 of injection pump and
mount the overflow pipe 6. (see Fig. 19,20)
( 9) Get rid of the air in fuel piping with the hand pump of
delivery pump until no bubble spills from the overflow pipe.
( 10) Pay attention to the moment of fuel dropping from o-
verflow pipe while turn the crankshaft slowly along its working
direction. Stop turning crankshaft as soon as the dropping oc-
curs, and the crankshaft angle is the very position of delivery
beginning for this cylinder. The delivery beginning angle can
be found in the relationship between crankshaft angle and pis-
Fig. 17 ,18,19,20
ton displacement (see Appendix 1) by comparing it with indi-
cated value on the dial gauge.

24
 ( 11 ) Adjustment should to be done if the measured angle differs from the required fuel supply advance
angle, which in the fuel system matching table.
Note: the valve might fall down into the cylinder if the turning angle is too big when the crankshaft is
turned. IiI order to prevent this situation occuning, clamp ring can be mounted in the groove of valve stem.
Examining by the flywheel mark:
There are TDC sign and scale on the end face or circumferentia of the flywheel (see Fig. 6). The scale
on the end face of flywheel is observed via the round hole 1 (see Fig. 21) below the starting motor on the
flywheel, lightening with flashlight, you can read the scale at the center of the circle. For the 8cale on the
circumferentia of flywheel, you can read it via the side window 2 on the flywheel housing ( see Fig. 22) and
the pointer.
( 1) Get rid of the air in fuel piping.
( 2) Loosen the connecting nut between the high - pressure pipe and fuel pump at the g~ end, divorce
the high pressure pipe from fuel pump.
(3) Turn the crankshaft along working rotating direction and make the piston of 1st cylinder (flywheel
end) at compression stroke, when turning continuously near delivery beginning, you should slow down and
observe the fuel level from the port of delivery valve holder, stop turning as soon as the level rises. Read the
degree of the angle scale before TDC from the flywheel, adjustment should be done to the fuel supply ad-
vance angle if the degree is out of standard.

Fig. 21 Fig. 22
How to adjust fuel supply advance angle:
Loosen the tightening nut of the injection pump flange, and turn the pump. The fuel supply advance an-
gle increases when the top end of injection pump is turned towards cylinder block, and the angle decreases
when doing in reverse. Check according to the above method after adjusting, and readjust until the advance
angle meet the stated requirement.
25
 The fuel supply advance angles for different models of diesel engine are listed in Fuel System Matching
Table.
Relationship among plunger diameter of injection pump, speed of engine and the
fuel supply advance angle:

1500 -1800

9 21
9.5 18
10 16
11 14

Injector assembly:
BOSCH S type nozzle is adopted for the diesel engine. Nozzles differ from each other in the number of
orifices, orifice diameter and angle of spray according to different requirements of the engines. See Fuel Sys-
tem Matching Table for details.
The fuel rough filter should be set before the fuel entering into delivery pump from fuel tank to protect
the delivery pump and the fuel fine filter.

3. 7 Lubricating system
The schematic diagram for lubricating system:

Piston

jet

Opening pressure
540-750kPa
I
I
I

l Fig. 23
The lubricating system consists of strainer, oil pump, oil cooler, oil filter and pressure limiting valve
26
etc.
The strainer is the intake opening of the oil pump, the connection between it and the inlet of oil pump
is sealed by 0 - ring, and special attention should be taken to avoid leakage during installing the connector,
otherwise the air sucked in the oil pump will influence oil supply so as to result in severe accidents like bear-
ing burning and engine damage. The oil pump is of gear pump. The pumped oil from oil pump enters into
the filter seat which has a safety valve (opening pressure is 540 -750kPa) on it. The oil will be vented to
oil sump when the pressure of oil pumped from oil pump exceeds the opening pressure value of safety valve.
There are sockets on the filter seat for pressure sensor and oil cooler. The oil cooler is con:nected in series
with the oil filter at the filter seat. The oil enters the oil cooler from filter seat, through the oil filter and re-
turns the filter seat, then enters the main oil passage. Each finned oil cooler has 9 cooling chips, according
to the actual need of different model, only one cooler can be used for the engine, also two or three coolers
can be used in series. If the engine - mounted oil cooler cant meet the requirement of oil cooling for the en-
gine, user may adopt out - connected cooler, but the filter seat 12273108 with oil inlet & outlet jointsahould
be used instead of the former seat. The oil filter is of spin - on type, and can be used only once. In the lu-
bricating system, pressure lubrication is adopted for the main bearing, connecting rod bearing, cam bearing,
two stage balance mechanism bearing, rocker bearing, injection pump, turbocharger, air compressor etc. ,
and splash lubrication is adopted for the connecting rod small end, gear train, piston, cylinder liner etc.

3. 8 Cooling system
Besides becoming kinetic energy to do work, the heat energy produced by the fuel burning in the com-
bustion chamber of the engine also heats up the cylinder head and cylinder liner etc. , therefore coolant cool-
ing should be used to prevent them from overheating and guarantee me engine to work reliably in order.
3.8. 1 Schematic drawing of the cooling system
The supercharged: inter - cooled diesel engine is equipped with supercharging air cooler( intercooler) ,
whichis positioned between the fan and radiator.

27
 Water outlet pipe

~
Q)
I
'0 Cylinder head
W
o ~
u Q)
~
Q) '0
o
§ u
.......
o

cylinder block

Fig. 24
3. 8. 2 Main components of cooling system
Water pump: the pump is of centrifugal type. The vortex passage of water pump is settled at inter-
mediate gasket, the water pump is integrated with the intermediate gasket and mounted at the front end face
of cylinder block. The cooling water enters into cylinder block through intermediate gasket. The impeller di-
ameter of water pump is 86mm or 110mm. Water pumps with different sizes should be chosen according to
the applied speed and requisite cooling flow of the diesel engine.
Water outlet pipe: the structure of water outlet pipe has two forms, one is welded part; and an-
other is cast part connected with intake manifold, the latter is applied to the following arrangement, i. e. the
water outlet of cylinder head is located at the flange surface of intake and exhaust ports, and the adopted
There is vent pipe (dia: 6mm) at the top of
built - in thermostat inside the water outlet pipe.
the water outlet, this pipe should be connected with expansion tank or the cavity of
upper water chamber of radiator, gas in the cooling system is guided out via this
pipe to prevent water overheating due to air resistance.
Thermostat: there are two kinds of thermostat types, one is outboard type and another is built - in
type. Its opening temperature is 75'C. When the outlet temperature of cooling water is lower than opening
temperature of the thermostat, the cooling water enters into water pump via the. outlet for minor circulation of
thermostat, and the temperatu":,,e of <:ooling water is quickly raised to reach the water temperature which the
diesel engine needed under normal operation; when the temperature of outlet water is higher than opening
temperature, the thermostat opens till full opening, all or partial cooling water enters the cooler to be
28
cooled, and then enters into water pump.
Radiator and fan: ( the radiator is supplied· according to users contract)
The radiator is fin and tube radiator, its capacity is configured according to the quantity of heat remov-
al. The fan is made of pressed metal sheet or extruded plastic; its diameter is 466, 520, 540 and 600mm.
The fan can be mounted on ,water pump.

3.9 Int9ke & exhaust system

This system includes air cleaner, intake manifold, exhaust manifold, exhaust muffler, exhaust turbo-
charger (for turbocharged diesel engine) , intercooler (for turbocharged and intercooled diesel engine) and
connecting pipes.

3.9. 1 Intake
The intake air for the engine should be clean and enough, therefore the intake air must be filtered and
the resistance in intake pipeline should be as small as possible.
Dry type paper element air cleaner is applied to 226B diesel engine for generating. The air cleaner with
corresponding capacity should be chosen for the engine with different power, and the cleaner with different
model should be chosen according to the dust content of ambient air in actual working site.
The dye type paper ele~ent filter usually has primary filter ( it can make the air produce swirling flow) ,
paper cartridge and safety element, as well as auto dust - extracting valve or exhaust arresting device in-
stalled after the primary filter to take off the dust from filtering. The resistance of the air cleaner should not
be too big, the allowable max. resistance under its unstained condition is 3kPa, and that under its stained
condition is 5kPa. There is maintenance indicator mounted at the vent port of air cleaner, when red
signal is given that means maintenance or replacement should be taken place in time, otherwise the
performance and service life will be influenced.
In mounting the air cleaner and connecting pipe, users should pay attention to its sealing and reliabili-
ty. Otherwise largely increased oil consumption, crankcase blow - by, decreased engine power, black smoke
exhaust and so on would occur because that the filter lose its effectiveness and is in short circuit leading early
wear of the engine and could not achieve the specified service life. It even causes the serious wear of cylin-
der liner and piston ring, and breakage of piston ring and cylinder scuffing.
The intake manifold of the engine is jointed by plates or cast by aluminum alloy, and there are various
structures for it to satisfy the requirements of different diesel engines. When the intake manifold is mounted
to the cylinder head, compound material gasket is used to aluminum manifold, while stainless steel gasket is
used to jointed manifold. The stainless steel gasket should be mounted with its convex surface facing to
the cylinder head. The tightening torque for tightening nut of intake manifold is 45 ± 5Nm.

3.9.2 Exhaust
29
 The three - cylinder or four - cylinder diesel engine adopts unitary exhaust m&nifol~, and the six - cyl-
inder engine adopts inserted exhaust manifold which is made up of two parts (every part for three cylinders)
and sealed wi.th narrow width ring. The joint between exhaust manifold and cylinder head is sealed with
stainless steel gasket, the convex surface of which should face to the cylinder head. The torque for
tightening nut is 45 ± 5Nm.
The exhaust resistance of diesel engine should be as small as possible; therefore the exhaust manifold
must have sufficient diameter or area and with bends <.IS few as possible, because the pertormance of engine
will be influenced Gbvio1:lsly if the exhaust resistance excee.ds a certain value. The sum of the resistances of
exhaust main and muffler should not be more than 7. 5 kPa for natural aspirated engl.tle, and not be more than
5 kPa for turbocharged engine.
In order to lower the surtace temperature of exhaust manifold and for safety reason, the exhaust manifold
should be wrapped with heatproof material and cO\(ered with armor plates, and high temperatare caution sign
as well. In addition to that, some of the engines adopt water jacket exhaust manifold.

Because the surtace temperature of the rear exhaust pipe, muffler, and expansion joint is very high, external
prevention measures should be provided. The exhaust gas of the engine contains nitrogen oxides, hydronitro-'
gen, oxycarbide and carbonic smoke particle. Frequently breathing in those exhaust gas or particles in large
amount will do hann to human, so such exhaust gas should be kept away from the personnels.

3. 9. 3 Turbocharging and inter - cooling system

Turbocharger: Both turbocharging models and the turbocharging inter - cooling models of the 226B se-
ries engine employ the radial flow exhaust turbocharger. See the accessory list for the those models. The oil
lubricating and cooling the turbocharger flows into the turbocharger from the main oil passage then directly
back into the crankcase.
The exhaust turbocharger is a kind of running mechanism at its high speed and high temperature.
The immediate halt when the engine is running at high speed and with large load is strictly forbid-
den. The right way is to decrease the load and the speed gradually and let the engine run idly for an-
other 5 - 10 minute so as to avoid any damage to the turbocharger bearing. After the turbocharger is
disassembled, someclean engine oil should be put at the oil inlet during the mounting process.
Charging air cooler (intercooler)
The temperature will go up after the air goes through the turbocharger and gets pressured. The intercool-
er of the 226B turbocharging inter - cooling engine features: air - air cooling. is used to lower the pressured
intake air temperature.
Air - air cooling intercooler ( delivered conforming with the contract) , generally speaking, is assembled
together with the circulating water radiator, cooled by fan. The intercooler can be placed in front of or at the
back of the radiator, determined by the wind direction of the fan. The intercooler could also be placed in
line with the radiator, determined by the overall fitting mechanism.
30
 The maximum acceptable flow resistance (supercharger to intercooler/ intercooler to engines) when the
pressured air from the supercharger is passing through the pressure pipe should be less than 2kPa. The flow
resistance while going through the intercooler should be less than 5. 0 - 5. 5 kPa. So the limit value of the to-
tal resistance when the pressured air is passing through pressure pipe and intercooler is 7. 0 - 7. 5 ( kPa) .

3. 10 Electrical system
The system is consisted of starter, chargeable generator, control instrument and storage battery. The
service voltage is 24V or 12V, subject to the choice of the customers.
Starter: The starter is a DC motor controlled by electromagnetism. Without specific requirement, the
rated power is 4kW at the working voltage of 24V and 2. 7kW at the working voltage of 12V.

L J
Fig 25 SC,hematic diagram of the starter
Generator: The generator is a kind of silicon rectifying generator equipped with transistor adjustor.
The rated voltage is 28V or 14V. The generator is connected parallelly with the storage battery. The genera-
tor is self - excited when working.

31
 w B+ D+

.8
ro

d----+-----lJ
Fig 26 Schematic diagram of the generator

Storage battery (generally self - prepared by the customers)

Storage battery capacity
Storage battery
Cylinder quantity Starter voltage V
capacity Ah
3,4 24 66
3,4 12 88
6 24 88
6 12 110
Monitoring instrument: The monitoring meter is an automatic diesel engine monitoring system, which can
accurately display the speed, oil pressure, water temperature and oil temperature. It can make timing moni-
toring to above parameters according to the setting of the customers and send signals like sound warning,
light warning and distant transmitting. There is interface on the monitoring meter, through which a remote
monitoring meter can be connected ( they must be used together). The monitoring instrument is delivered ac-
cording to the contract. Refer to the monitoring instrument instruction for detailed information about it.

32
Schematic diagram of the electric circuit connection

13

1. diesel engine 11. connecting wire from starting button

2. starter 12. meter cover
3. adjustor of the generator 13. ignition lock
4. AC generator 14. starting button
5. the connecting wire from the AC generator to starter 15. temperature warning light
6. storage battery 16. oil pressure warning light
7. the anode connecting wire to the starter 17. charging indicator light
8. earth wire 18. temperature sensor
9. connecting wire from starter to charging indicator 19. oil pressure sensor
10. connecting wire from starter to ignition lock

33
3. 11 Main bolts tightening torque
Tighi:ei~ing torque ( Nm)
No. Name of bolt Specification
Maximum ( max) Minimum( min)
Pre - tighten with a torque of
M14 -10.9
1 Cylinder head bolt 30Nm, tum 1:1.0 0, then again turn
M14 -12.9
120°
Pre - tighten with a torque of
2 Main bearing bolt M14 -10.9
70Nm,turn 90°
Tightening nut of intake pipe and ex-
3 M10 -10 45 50
haust pipe
4 Flywheel pipe M16 -10.9 285 295
M16 -10.9 240 250
5 Fastening boss of crankshaft boss
M16 -12.9 300 310
MI0 -8.8 45 50
Fastening holt of the pulley on the
6 MI0 -10.9 65 70
boss
M12 -8.8 85· 90
MID -8.8 45 50
7 Fastening bolt of the dampener
MI0 -10.9 65 70
Tightening bolt of the camshaft gear
Durlok M8 - 12. 9 55 60
8 and the fastening holt of camshaft
MI0 * 1. 25 -10.9 85 90
gear and fuel injection pump gear
Fastening bolt of the mounting gear at M14 * 1. 5 85 100
9
the oil injector camshaft M18 * 1.5 100 110
Pre - tighten with a torque of
10 Connecting rod bolt M12 * 1. 5 - 12. 9
30Nm, turn 60°
M12 -12.9 140 145
Fastening bolt of the flywheel housing M12 -10.9 110 120
11
and other fastening bolt and stud bolt M10 -12.9 80 85
MI0 -10.9 60 65

Fastening bolt of oil pan, hexagon

M8 -8.8 20 25
12 cylinder - head bolt for bearing the
M8 -10.9 30 35
oil pan.
Fastening bolt of two stage balancing
13 M10 -8.8 35 40
mechanism
Fastening bolt of oil pump and the Durlok M8 - 12. 9 30 40
14
stud bolt with self -locking nut M8 -8.8 20 25

34
 Construction bolt of rocker ann sup-
15 MID -8.8 40 45
port

16 Adjusting nut of rocker ann M9 * 1 20 25

Fastening bolt of cylinder head hous-

17 M8 -8.8 10 15
ing
Fastening support for tightening the
18 33 37
oil injection pump delivery valve
Fastening bolt of high pressure fuel M12 * 1. 5 20 25
19
pipe MI4 * 1. 5 20 25

20 Fastening nut of oil injector M8 10 15

MIO -10.9 60 65
21 Fastening bolt of hydraulic pump
M8 -10.9 30 35

22 Fastening bolt of AC generator pulley MI4 35 40

35
4. Operating requirement and procedures
4.1 Rules on the working fluid and the auxiliary material
4.1.1 oil
Quality class: Oil is classified according to its quality and characteristics, usually on the basis of API . Oil
which is allowed to use
API class: CC,CD,CD - n,CE
CC class oil should be selected for non - supercharged diesel engines while the CD class oil for the super-
charged ones. It is allowable for the low - quality oil to be replaced with high - quality oil.
Viscosity
The viscosity of the oil is , to a great extent, detennined by the temperature. Refer to the right figure for ap-
propriate oil viscosity class ( SAE class).
Please refer to the right figure for the oil viscosity and select the most appropriate oil. The situation where
the environment temperature is close to the temperature limit will have some influence on the cold start per-
fonnance but not necessarily damage the diesel engine.
Do not exceed the temperature limit for long time so as to keep the abrasion within a minimum extent.
Multi - class oil could be used so that it wont be necessary to change the oil during the seasonal alternation
period.
The fuel consumption rate could be lowered by using multi - class oil (light oil especially)
It is recommended to use 15W/40 oil when the environment temperature is above -15CC and use
5W/30 when it is below - 15CC.

OF 86

77

68 +20

59

50 +10

41

32 0

23

14 -10

-4 -20

-13

-22 -30

-31

-40 -40

•
*

36
*
+
4. 1.2 fuel
.This engine makes use of light diesel as the fuel.
Quality grade
Sulfur content of specified brand·fuel is not allowed to exceed I % .
The fuel with following brand numbers is permissible:
- DIN 51601
- NATO CODES F54,F57,F76
- BS 2869 :Al ,A2 (pay attention to the sulfur content of the A2)
- ASTM 0975 -81:1 - D,2 - D
- W -F -800C:DF -A,DF -1,DF-2
The waxiness produced by the diesel under low temperature will lead to the low fluidity of the diesel and the
blockage of the fuel system and eventually result in the operating failure of the diesel engine.
So please use winter diesel when the environment temperature is blow oOC.
When the temperature is between -15OC and - 20CC , the diesel engine could employ a mixture of diesel
and kerosene to meet the low temperature requirement. Refer to the right figure for the mixing ratio.
In the case that the summer diesel has to be used at a temperature of blow DOC , some kerosene which do not
exceed 60% could be added, as is illustrated in the figure blow.

+32 0

+23 -5

+14 -10

+5 -15

-4 -20

-'13 -25

-22

t t 0 10 20 30 40 50 60%
OF OC Mixing ratio - .
I 'Ambient temp

Notice: the mixing process should he proceeded in the fuel tank. Fill in some diesel before adding enough
kerosene.
4. 1. 3 cooling fluid
The cooling water of the diesel engine must be soft water and anticorrosive agent and anti - freezing agent
must be added.
Anti - freezing fluid
Please refer to the anti - freezing fluid instruction for the mixing ratio of the longacting anti - freezing fluid.
Longacting anti - freezing fluid
37
 Glycol content % 33 50 56

Density( 15. 6CC) 1.05 1.074 1.082

Boiling pointCC 104.5 ± 1 108.5 ± 1 110.0 ± 1

Freezing pointCC -18 ±1 -36 ±1

- -45 ±1

Min. temperature appropriate CC -10 -26 -35

The concentration of the anti - freezing agent should be checked once every 1()()() hours. But there should be
at least one checkout in every season. The anti - freezing agent should be changed every two years 80 as to a-
void corrosive damage.
Anticorrosive agent
Anticorrosive agent can be added to the cooling water when the environment temperature is above 5CC (in
sUmmer or autumn or in some areas with relatively high temperature).
Cooling water
The compositions of the cooling water are analyzed as following:

Water quality nun. max. I

PH value 6.5 8.5

The content of chloride ion
- 100 Only the water with
(mgldm3 )
the compositions ·of
Content of carbonate (mgldm3 ) - 100
specified content ~
Content of overall anion (mgldm3 ) - 150 he added with addititin
Degree of hardness when using the agent
3 12
anti - freezing agent

Degree of hardness of the carbonate 3 -

Notice, the instruction of
Degree of hardness whenusing
the supplier
chemical anticorrosive agent
0
I 10

Inner zinc - plated pipe is not appropriate for containing chemical anticorrosive agent 80 it cannot be used as
cooling water pipe.
4. 1.4 Treating of waste fueVoil
Waste fuel and oil should be stored in a special container. Because there exist poisonous substances in fuel,
oil and coolant, drink or contact with skin is forbidden.
38
4. 2 swinging requirement
Inappropriate swinging might damage the diesel engine during the conveying process.

B
It is 'inappropriate to use a rope and a triangle to sling the engine up. Because if the slings, the cylinder
head bolt and the s~inging ring are not kept in a line, the cylinder head bolt might be damaged or even frac-
tured during the swinging process, which may eventually result in the failure of the engine.

4. 3 Preparation before the start

Notice: The engine should not be started until it has been installed in a appropriate way and
placed in a final position. H the engine is operated in a closed environment, make sure there is good ventila- I

tion and that the exhaust gas is discharged into the atmosphere.

4. 3. 1 Engine oil filling

1. The oil must meet the specified requirement, otherwise, the oil pressure
might fall short resulting in abrasion and starting difficulty. The oil must be very clean.
2. Screw down the oil - draining plug
3. Open the oil cap and fill in the oil. The oil must be filtered through a dross filter when it is filled in.
4. Put the engine at a level position; pull out the dipstick to examine the height of oil level. Fill the oil
up to the upper limit of the dipstick, if necessary.
5. Screw down the oil cap.
Notice: The height of oil level must be checked out every time before starting the engine.

39
4. 3. 2 Filling in the fuel
1. The diese~. b~ing used must comply with the regulation.
2. Pay attentiQn to the cleanness of the diesel; it had better be stored for at least 72 hours before being
filled into the engine. The diesel should be filled into the tank through a build - in dross filter.
Notice: The diesel level should be checked every time before starting the engine.

4.3.3 Deflation of the fuel system

1. Unloosen the fuel bolt 1(at the fuel outlet of the fuel supply pump) for half a round. Pump with the
hand pump 2 of the fuel supply pump 3 until there is diesel coming out; screw down the fuel bolt.
2. Open the deflating bolt 4 on the fuel filter 5. Pump with the hand pump of the fuel supply pump until
there is diesel coming out; screw down the deflating bolt.
3. Open the deflating bolt 6 on the fuel injection pump 7. Pump with the hand pump of the fuel supply
pump until there is diesel coming out; screw down the deflating holt.
4. Continue pumping with the hand pump and check whether there is leakage in the fuel pipe, then
screw down the hand pump.

4.3.4 Filling in cooling fluid

The cooling fluid is compounded with softened clean water and anticorrosive agent( or anti - freezing agent).
The whole compounding process must be proceeded strictly in accordance with the regulations set by the
40
manufacturer.
Notice: Frequent water - adding and water - changing might result in the existence of the· incrusta-
tion. The leakage of the cooling system should be repaired as soon as possible. Add clean soft water
as much as possible and avoid changing the cooling fluid, if possible. The cooling fluid drained from
the water tank can be recycled after being nltered through fabric and fine structure mesh. Fill in the
cooling fluid from the water inlet of the radiator or heat exchanger and discharge the air of the cooling cycling
system. Refer to the 4. 1 for the regulations of the operating fluid and auxiliary material, if there is a need to
add anti - freezing agent. The liquid level of the cooling fluid level must be checked out every ti.:ie before
starting the engine.

4. 3. 5 The charging of the storage battery

Refer to the storage battery instruction.
Notice: The gas produced during charging proc~ is quite explosive. So it is forbidden to
smoke around the battery. Keep any open fire and spark away froJJl the battery. The acid of the
battery has strong corrosivity. H it is splashed in the eye or on the skin, wash them with large a-
mount of water immediately.
The operating sequence of c?arging process
1. Open the sealing cover.
2. Fill into sulfuric acid from the filler port until the surface reaches the marker.
3. Fasten the sealing cover
4. Coat the electrode of the battery with anticorrosive grease
S. Connect the connecting rod with the binding post, connect the anode first
6. It is not allowed to place any metallic object on the battery
7. Check the sulfuric acid surface every day. Add distilled water if necessary.

4.4 Start
-rnfus~ the raw water pump of the marine engine with water. Rotate the crankshaft a few round before starting
the engine to make sure there is no rotation obstruction.
1. Put the speeder rod in the central position
2. Connect through the power switch
3. Turn on the starting switch until the engine is started (The maximum starting time every time is 6 sec-
ond).
4. Immediately check the oil pressure after the starting. IT the oil pressure is less than lOOkPa, stop the en-
gine and get rid of the failure.
S. Warm the engine up before operating at full load, check the cooling fluid circulation and whether the oil
pressure is norntal.
6. Check the Three Leakage condition every time after the operation of the engine.
41
 Notice: When the engine is running, it is not allowed to remove the cables which are connected to
the voltage regulator and the battery anode. Differing from the DC generator, it is forbidden to go
through voltage checking on the AC generator by the means of temporary earthing.

4. 5 Speed regulating
On the engine whose speed IS variable, the engine
. speed can be increased by turning the speeder rod in
the direction shown in Fig 2. Screw out blocking nut 3
and loosen the locknut 4 to carry out idle speed regula-
tion. It is not allowed to open the lead sealed cover 5.
The speeder rod 1 can be pulled by pull rod or coated
steel wire.

4. 5. 1 Speed fine - regulating mechanism

The speed fine - regulating mechanism is used to the fixed - speed engine.
Umoose the bllJcking 7, rotate knurled screw 6 to regulate the speed: turning clockwise will increase the
speed, while turning counterclockwise will decrease it. Lock the nut 7 after speed regulating.

4. 6 stopping the engine

Do not try to stop the engine at full load. Decrease the speed before stopping 'the engine and let it run idly for
another 5 to 10 minutes. When trying to stop the engine manually, press the stopping rod 8 downwards until
the flywheel stops rotating or the instrument board indicates "zero". Engine stopping mechanism, if using e-
lectromagnetic valve, the engine will stop two minutes after the switchover from " open" to "close". Shut
the power off after the engine is stopped.
As for the engine whose circulating water is not added with anti - freezing fluid, in winter the cooling
water must be drained off after the engine is stopped so as to prevent the engine from being damaged
Dewatering outlet is on the oil cooler. The water inside the engine can be drained away by screw out water-
42
discharging bolt. At the same time, the water - discharging bolt of the inter - cooler (regarding the super-
charging inter - cooler engine) should also be screwed out to drain away the water inside the inter - cooler.

4. 7 Operating enviro~ent
If the environment temperature is above -15CC, the engine can be operated in a normal way. If the tempei'-
ature is between -15CC and - 35CC , it should be started with the help of auxiliary device. If the altitude or
the temperature is too high, the engine power should be modified. The engine is not anti - explosive, so keep
it away from the inflammable explosive environment.
The ambient illumination for engine should be more than 201ux.
The engine is not suitable for underground operation.

43
5. M'aintenance
5. 1 Time table for Maintenance
There is no need to repeat after following the maintenance schedule
Operating
Working items
time h
Re - tighten the connecting bolt and cylinder head bolt 30
Check the belt and tension 30 125
Change the oil and oil filter element 30 125
Check valve clearance 30 125

Repeat the maintenance procedure following the timetable below

Operating time h
Working items
250 500 1000
,
Clean up the air filte~· element 1) x
Check and tension the V belt x
Change the oil and oil filter element x
Check valve clearance x
Change the fuel filter element x
Clean up the crankcase ventilation mechanism 2) x

1 ) The change should be made earlier in dusty place.

Wet air filter should be cleaned every 200 hours (at most) .
2) Only under the circumstances where the crankcase ventilation mechanism does not intake the air.
The maintenance instructions for the backup conditi~n and emergency.
If the diesel engine does not operate for weeks ( eg, in winter) , it must be sealed u..p( see 5.2. 11).

Time period Requirement

Every month Trial running with load see 5. 2. 10

If the running time does not reach 500 hours after 6 months, the required maintenance
6 months
procedure must be carried out during this period.

After 12 If the running time does not reach 1000 hours after 12 months, the required mainte-
mounths nance procedure of this period must be carried out during this period.

44
Overhaul
The reliablity of the engine might be affected because of abrasion and corrosion. In order to avoid any work-
ing abnonnity of the engine, we recommend the following overhaul. The first overhaul should be proceeded
after the engine has runned for 2000 hours or after two years ( running time less than 2000 hours).

Items Running time

Check the nozzle 2000
Check compressive pressure 2000
Check bearing clearance of the water pump 5000
Check supercharger 5000
Check fuel injection pump ·5000
Check cylinder head 5000
Check cylinder liner 5000
Clear the water jacket space of the water cooling exhuaust pipe and check the corrosion 10000
Check connecting rod and main bearing 10000
Check pistion 10000
Check the crankshaft 10000
Check the camshaft 10000
Check the two - stage balancing mechanism 10000
Check the drive gear 10000
Overhaul fuel injection pump 10000
Change oil pump 10000
'Change water pump 10000
Change the oil sealing of the crankshaft 10000
Change tb.e damper 10000

Above overhaul require expertise and should be carried out by professionals.

5. 2 Maintenance procedure
5. 2. 1 cleaning up dry air filter
When the maintenance indicator of the filter shows a red signal or the engine perfonnance is affected because
of the resistance of the filter, clean the filter or change the filter element.
1. Dismount the main filter element
2. Lay the end surface downwards and flap the filter element carefully. Or put the filter element on dean
ground and roll it to shake the dust off. Do not beat it forcibly.
3. Blow from the inside and ouside the surface of the filter element with compressed air (less than 500kPa).
45
4. clean up me sealing packing. It should be changed if there is any damage.
5. c~ck the dust outlet in the dust - discharging valve.
6. Reinstall. IT the filter is mounted horizontally, place the dust - discharging valve vertically downward
when mounting the cover.

Notice: TIle main filter element of a filter can only be cleaned up for at most 5 times. It must be changed af-
ter a year, and should be immediately changed if there is a damage. Mark the number of times which the
main filter element has been cleaned or changed for in the exclusive marking column of the safe filter ele-
ment. The safe filter element must be changed under following circumstances:
1 ) Main filter element has been maintained for 5 times.
2) It has been used for 2 years.
3) As soon as the main filter element is maintained, the maintenance indicator will show immediately.
4 ) Mter the operation with a defective main filter element.
5 ) Safety filter element is not allowed to be cleaned.

5.2.2 Check connection bolt

Check the bolts for diesel engine, generator, injector and intake!exhaust manifold and the connection of
bolts and hoses, retighten them if necessary.

5. 2. 2. 1 Tighten cylinder head bolts

Loosen the cylinder head bolts about 1/4 of a rotation when engine warming, and then tighten them up with
a force of 200 + lONm immediately according to the sequence as the following figure.

46
5. 2. 3 Check and tension the V - belt
~ess the V - belt with hand, the distortion should not be more than 10 - 15mm, otherwise change the belt
with a new one.
If tension the belt through generator, loose bolt 1 and bolt 2 firstly, strain the generator outwards, then tight-
en tip bolt 1 and bolt 2 and check the belt by hand.
If tension the belt through tension pulley, loose the bolt 3 and bolt 4 on bracket 5, stain the tension pulley
bracket, and then tighten up bolt 3 and bolt 4 and then check the belt by hand.

Caution: Change the damaged or oiled belt.

5.2.4 Change oil

a. Start the engine and stop it after reaching the operation temperature.
b. Place an oil tank under the engine.
c. Screw out the drainage screw plug 1, pay attention the seal ring on the screw plug.
d. Drain off all oil.
e. Screw on the screw plug 1 with seal ring.
f. Fill up clean oil.
5.2.4. 1 Replace oil filter
a. Disassemble the oil filter 1 with special wrench.
b. Coat some oil on the seal ring 2 and tighten up the oil filter by hand.
c. Check the oil filter for tightness in running - in.

47
5. 2. 5 Check valve clearance
a. Remove cylinder head cover.
b. Make the piston reached the firing TDC.
c. Check the clearance between rocker arm and valve rod end with a O. 2mm or O. 3mm feeler gauge 1. Ad-
just the clearance according to the following steps if necessary.
d. Loose nut 2, adjust the clearance with screw 3.
e. Holding the position of screw 3 and tighten nut 2.
f. Check the other clearances with feeler gauge 1.
g. Set up rocker arm cover and tighten the screws. The rocker arm cover seal side should be faced with the
gasket.
Caution: Adjust valve clearance according to the firing order to avoid turning crankshaft unnecessarily.

5. 2. 6 Change fuel filter

1 Close the valve on fuel circuit.
2 Turn the special tools of fuel filter counter - clockwise. Disassemble the fuel filter 1.
3 Before mounting new filter, coat lubricating oil on seal ring 2.
4 Tighten the new filter by hand.
5 Open the valve on fuel circuit.
6 Degas the fuel system.
7 Check the sealing of fuel filter.

5.2.7 Clean breather body

1 Loosen the hexagon nut or screw 1.
2 Loosen hose clip 2.
3 Disassemble breather body 3.
4 Pay attention to the 0 seal ring.
5 Clean the breather body in diesel.
6 Mount the breather body, change new 0 seal ring if necessary.
7 Tighten the hose clip 2.
8 Tighten the hexagon nut or screw 1.

5.2.8 Clean intercooler

In the operation of intercooler, if enlarged cooled air resistance and the decreased difference in temperature
affect the performance of diesel engine, the intercooler should be cleaned.

48
5. 2. 9 Run - in
If the engine is in standby or emergency state, run it once a month so as to prevent it from corrosion damage.
1 Mter starting, check the instrument meter at once, put 1/3 load on the engine.
2 After running for 10 minutes, increase to 3/4 load.
3 Mter running for another 10 minutes, increase to full load.
4 Check the sealing of the engine.
5 Run the engine at 1/3 load for 10 minutes.
6 Unload and stop the engine.

5. 2. 10 Engine maintenance
If the engine stops for a long time ( for several weeks) , the following protective measures must be taken so as
to prevent it from corrosion damage:
Operating order:
1. Rinse the exterior of diesel engine.
2. Drain off the oil inside the engine and the fuel in iqjection pump.
3. Add corrosion preventive to the engine.
4. Drain off fuel.
5. Mix fuel oil and corrosion preventive on the scale of 9 : 1.
6. Fill the fuel tank with the mixture above.
7. Drain cooling water.
8. Add emulsifiable corrosion preventive to the cooling water according to the degree of 5%.
9. Add above compound to cooling system, and vent air from the ~ystem.

10 . Start the engine and run it for 10 minutes.

11. Stop the engine and turn flywheel for several circles to make the combustion chamber sufficiently wet.
12. Drain off cooling water.
13. Smear exposed parts of the engine with corrosion preventive grease.
14. Close the intake manifold and exhaust manifold.
15. Repeat the above operations after three months.
When the engine is demanded to put into service, you should:
1. Drain off C?orrosion preventive and mixed fuel.
2. Add oil to the engine.
3. Add fuel and coolant, vent air from the fuel system and cooling system.
4. Remove corrosion preventive grease on the exterior parts.
5. Open the ports of intake manifold and exhaust manifold.

49
 6. Trouble shooting:
Failure The
to
•
IIBJffi Unew:n W InJufr Unew:n
-cimt IlIJIIing me -icim mgine OMhe kmc-
• Cylirxlfr

llllIt sq. Il1lpJt d eduult cil lljlM1 -aoo ~ Cause Remedy

the IJ't':lIllIIl:
~
The battery power is insufficient, connector of wire be-
~ Check and charge
comes loose
~ Governor handle is not in the starting position Turn the governor handle to the starting position
~ Stop lever is in the stop position Loosen the stop lever
~ ~ ~ ~ ~ Insufficient fuel Add fuel
~ ~ Incorrect lub - oil grade Renew the lub - oil according to requirements
~ ~ ~ ~ ~ ~ ~ Injector works abnormally Check the injector, repair or replace it
~ ~ ~ ~ Incorrect valve clearance Adjust according to requirements
~ ~ Air cleaner is unclean Clean or replace it
~ ~ ~ Compression pressure is insufficient Inspect and adjust
~ ~ ~ ~ Governer is out of order Repair
~ ~ t.. Fuel filter is unclean Replace
Ul
o ~ ~ Over oiling Drain off unnecessary oil
~ Oil filter is unclean Replace
~ Oil pressure regulating valve is open Check and clean it
~ V belt loosened Tension it according to requirements
~ Insufficient cooling water Add cooling water
~ Thermostat or water pump works abnormally Repair or replace
~ lit.. Engine is too cold
~ ~ ~ ~ Engine overloading Decrease the load
Yalve phase is incorrect or camshaft is assembled im-
~ ~ ~ ~ ~ oroperlv
Inspect and repair
~ ~ ~ ~ ~ Air in the fuel system Drain off air from the system
L ~ Incorrect fuel supply advance angle Check and correct the advance angle
flow path of air compressor housing and impeller of the
L ~ turbochar(rer are unclean
Rinse
~ ~ Big resistance in intercooler, low cooling efficiency Rinse
~ ~ Exhaust resistance is too big Find out the cause au-J eliminate it
~ Faults in turbocharger Replace the assembly
~ Cooling efficiency of freshwater cooler decreases severely Clean up
.~
Drain off air from the syEtem and eliminate the sucnon
Air sucked into the cooling system
oosition
Oil strainer clogged up, oil suction pipe leaks Inspect, clean and repair
Appendix 1: Relationship between crankshaft angle <Il and piston displacement S

S(mm) <1>( ) S(mm) <1>( ) S(mm) <1>( ) S(mm) <1>( ) S(mm) <1>( )

0.1 2.90 3.6 17.53 8.1 26.51 12.6 33.34 17. 1 39.18
0.15 3.56 3.7 17.77 8.2 26.68 12.7 33.48 17.2 39.31
0.2 4.11 3.8 18.02 8.3 26.84 12.8 33.62 17.3 39.43
0.25 4.59 3.9 18.25 8.4 27.01 12.9 33.76 17.4 39.55
0.3 5.03 4.0 18.49 8.5 27.18 13.0 33.89 17.5 39.67
0.35 5.43 4.1 18.72 8.6 27.34 13. 1 34.03 17.6 39.79
0.4 5.81 4.2 18.95 8.7 27.50 13.2 34.16 17.7 39.~1
0.45 6.16 4.3 19.18 8.8 27.67 13.3 34.29 17.8 40.03
0.5 6.50 4.4 19.47 8.9 27.83 13.4 34.43 17.9 40.15
0.55 6.81 4.5 19.63 9.0 27.99 13.5 34.57 18.0 40.27
0.6 7.12 4.6 19.85 9.1 28. 15 13.6 34.71 18.1 40.39
0.65 7.41 4.7 20.07 9.2 28.31 13.7 34.84 18.2 40.51
0.7 7.69 4.8 20.28 9.3 28.47 13.8 34.97 18.3 40.63
0.75 7.96 4.9 20.5 9.4 28.78 13.9 35.11 18.4 40.75
0.8 8.22 5.0 20. 71 9.5 14.0 35.24 18.5 40.87
0.85 8.48 5. 1 20.92 9.6 28.94 14. 1 35.38 18.6 40.99
0.9 8.72 5.2 21. 13 9. 7 29. 10 14.2 35.51 18.7 41. 11
0.95 8.69 5.3 21. 33 9.8 29.25 14.3 35.64 18.8 41.22
1.0 9.20 5.4 21.54 9.9 29.40 14.4 35.77 18.9 41. 34
1.05 9.42 5.5 21. 74 10.0 29.56 14.5 35.90 19.0 41.45
1.1 9.65 5.6 21.94 10.1 29.71 14.6 36.03 19.1 41. 58
1.2 10.07 5.7 22. 14 10.2 29.86 14.7 36. 16 19.2 41.69
1.3 10.49 5.8 22.34 10.3 30.02 14.8 36.29 19.3 41.81
1.4 10.89 5.9 22.53 10.4 30.17 14.9 36.42 19.4 41.93
1.5 11.27 6.0 22.73 10.5 30.32 15.0 36.55 19.5 42.04
1.6 11. 64 6.1 22.92 10.6 30.47 15. 1 36.68 19.6 42.16
1.7 12.00 6.2 23.11 10.7 30.62 15.2 36.80 19. 7 42.28
1.8 12.36 6.3 23.30 10.8 30.76 15.3 36.93 19.8 42.39
1.9 12.70 6.4 23.49 10.9 30.91 15.4 37.06 19.9 42.51
2.0 13.03 6.5 23.68 11. 0 31.06 15.5 37.19 20.0 42.62
2.1 13.35 6.6 23.86 11. 1 31. 21 15.6 37.32 20.1 42.74
2.2 13.67 6.7 24.05 11. 2 31.35 15.7 37.44 20.2 42.85
2.3 13.98 6.8 24.23 11. 3 31.50 15.8 37.57 20.3 42.97
2.4 14.28 6.9 24.41 11.4 31.64 15.9 37.69 20.4 43.08
2.5 14.58 7.0 24.59 11. 5 31.79 16.0 37.82 20.5 43.20
2.6 14.87 7.1 24.77 11. 6 31.93 16.1 37.94 20.6 43.31
2.7 15.16 7.2 24.95 11. 7 32.07 16.2 38.07 20. 7 43.42
2.8 15.44 7.3 25. 13 11. 8 32.22 16.3 38. 19 20.8 43.54
2.9 15.71 7.4 25.30 11. 9 3.36 16.4 38.32 20.9 43.65
3.0 15.98 7.5 25.48 12.0 3.50 16.5 38.44 21.0 43.77
3.1 16.25 7.6 25.65 12.1 32.64 16.6 38.57 21. 1 43.88
3.2 16.51 7.7 25.83 12.2 32.78 16.7 38.70 21. 2 43.99
3.3 16.77 7.8 26. 00 12.3 32.92 16.8 38.82 21. 3 44.10
3.4 17.03 7.9 26. 17 12.4 33.06 16.9 38.94 21. 4 44.21
3.5 17.28 8.0 26.34 12.5 33.20 17.0 39.06 21. 5 44.33

51
Appendix 2· Wear Limits of Parts of the Enl!lne
Dimension( mm)

No. Part name & measuring point Original state

Max. wear limit
Max. Min.

Crankshaft
Dia. of main journal 69.93
69.97 69.951
1 Dia. of conrod journal 62.93
62.97 62.951
Length of thrust main journal 36.07
36.05 36.00
Axial clearance measured after mounting 0.4

2 Main bearing All the two bearings must be

t - - - - - + - - - - - - - - - - - - - - - - - - + - - - - - t - - - - - l replaced if the plated trimetal
3 Conrod bearing layer or guad alloy layer is
worn down
4 Thick of crankshaft thrust washer 3.47 3.42

5 Dia. of conrod small end bushing 35.08 35.03 35.15

Piston pinExternal cylindrical sunaceOutside Replace if there is scoring

6 35.00 34.994
dia. of piston pin 34.990
TD/TBD 226B Piston assembly
Replace if there is wear
1st ring groove ( trapezoid)
2.11
2nd ring groove
4.11
3rd ring groove
Replace if there is evident
Piston pin bore
clearance.
2.07 2.05 Replace if there is vertical
7 Contact sunace of piston skirt
End clearance of piston ring ( all)
4.06 4.04 sconng
1st piston ring (trapezoid ring) 2.00
Replace if there is wear on
inclined end face of the ring
Clearance of 2nd piston ring in groove
0.200.
Clearance of 3rd piston ring (oil ring) III
15
groove

D226B Piston assembly

1st ring groove ( trapezoid) Replace if there is wear
2.10
2nd ring groove
4.11
3rd ring groove
Replace if there is evident
Piston pin bore
clearance.
8 Contact sunace for piston skirt
2.06 2.04 Replace if there is vertical
End clearance of piston ring( all)
4.06 4.04 sconng
1st piston ring (trapezoid ring) 2.00
Replace if there is wear on
Clearance of 2nd piston ring in groove inclined end face of the ring
Clearance of 3rd piston ring (oil ring) III
0.20
0.15
groove

Cylinder liner 105.250

9 Inside diameter 105.022 105.00 Replace if vertical scoring
Honing sunace exceeds O. 05

52
 Dimension( mm)

No. Part name· & measuring point Original state

Max. wear limit
Max. Min.

D/TD/TBD226B Valve and valve guide 8.9"'j2 8.945

8.970
Dia. of valve stem 9.060
9.015 9:'JOG
10 Dia. of valve guide bore
Height between valve bottom face 1. 80
1.42 1.03
and cylinder head face

Rocker seat
11 15.984 15.966 15.950
Dia. of rocker shaft

12 Dia. of rocker bearing bore 16.018 16.000 16.040

Camshaft Replace if there is wear

Intake & exhaust cam face 46.940 46.920
46.960
13 Dia. of camshaft journal 7.10 7.220
7. 190
Width of camshaft locating slot Axial clearance: O. 40
Axial clearance of camshaft after mounting

Dia. of camshaft bearing bore on

cylinder block 47.045 46.990 47.060
Bore with bearing mounted in (gear end) 47.025 47.000 47.050
14 Bore without bearing mounted in
Inside dia. of tappet hole on cylinder 17.518 17.500 17.530
block

Thick of tooth sector for camshaft

15 7.005 6.850 6. 750
location

16 Outside dia. of tappet 17.494 17.483 17.475

Two stage balance shaft assembly

33.940
Dia. of balance shaft journal
17 33.975 33.950
Axial clearance of balance shaft assembly
Axial clearance: O. 50
after mounting

18 Inside dia. of balance shaft bearing bushing 34.050 34.010 34. 080 (after mounting)

19 Thick of balance shaft thrust washer 3.55 3.45 3.35

53
~ 17; ~~ it ~tk~ ~~;;fj f!l~;iJ
Weirang Weichai Deulz Diesel Engine Company Ltd
Jt!!~I:: III fJ,1'ii!ll;Jjj'j~tg*I!j 121-<:-
It! i1;: +86-0536-8679536
111 Jl: +86-0536-8679526
IhIS!W: 261009
Weirang Weichai Deulz Diesel Engine Company Ltd
Add:No.121 Beigong Slreel, Weirang
Shandong 261001,P.R.China.
Tel:+86-0536-8679536
Fax: +86-0536-8679526
Poslac: 261009