Version: V1.00.

000
Revised date: March 19, 2021

Statement: LAUNCH owns the complete intellectual property rights for the
software used by this product. For any reverse engineering or cracking actions
against the software, LAUNCH will block the use of this product and reserve the
right to pursue their legal liabilities.
LAUNCH X-431 PRO3S+ V2.0 User Manual

Copyright Information
Copyright © 2021 by LAUNCH TECH CO., LTD. All rights reserved. No part of
this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording or
otherwise, without the prior written permission of LAUNCH. The information
contained herein is designed only for the use of this unit. LAUNCH is not
responsible for any use of this information as applied to other units.
Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or
third parties for damages, losses, costs, or expenses incurred by purchaser or
third parties as a result of: Accident, misuse, or abuse of this unit, or
unauthorized modifications, repairs, or alterations to this unit, or failure to strictly
comply with LAUNCH operating and maintenance instructions. LAUNCH shall
not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original LAUNCH
Products or LAUNCH Approved Products by LAUNCH.

Trademark Information
LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (LAUNCH) in
China and other countries. All other LAUNCH trademarks, service marks,
domain names, logos, and company names referred to in this manual are either
trademarks, registered trademarks, service marks, domain names, logos,
company names of or are otherwise the property of LAUNCH or its affiliates. In
countries where any of the LAUNCH trademarks, service marks, domain names,
logos and company names are not registered, LAUNCH claims other rights
associated with unregistered trademarks, service marks, domain names, logos,
and company names. Other products or company names referred to in this
manual may be trademarks of their respective owners. You may not use any
trademark, service mark, domain name, logo, or company name of LAUNCH or
any third party without permission from the owner of the applicable trademark,
service mark, domain name, logo, or company name. You may contact LAUNCH
by visiting the website at www.cnlaunch.com, or writing to LAUNCH TECH CO.,
LTD., Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian,
Longgang, Shenzhen, Guangdong, P.R.China, to request written permission to
use Materials on this manual for purposes or for all other questions relating to
this manual.

i
LAUNCH X-431 PRO3S+ V2.0 User Manual

Important Safety Precautions

Important: To avoid personal injury, property damage, or accidental damage to
the product, read all of the information in this section before using the product.
 Never collide, throw, or puncture the tool, and avoid falling, extruding and
bending it.
 Do not insert foreign objects into or place heavy objects on your device.
Sensitive components inside might cause damage.
 Do not use the tool in exceptionally cold or hot, dusty, damp or dry
environments.
 In places using the tool may cause interference or generate a potential risk,
please turn it off.
 This tool is a sealed unit. There are no end-user serviceable parts inside. All
internal repairs must be done by an authorized repair facility or qualified
technician. If there is any inquiry, please contact the dealer.
 Never place the tool into apparatus with strong electromagnetic field.
 Keep the tool far away from magnetic devices because its radiations can
damage the screen and erase the data stored on the tool.
 DANGER: Do not attempt to replace the internal rechargeable lithium battery.
Contact the dealer for factory replacement.
 CAUTION: Please use the included battery and charger. Risk of explosion if
the battery is replaced with an incorrect type.

Precautions on Using this tool

Before using this tool, please read the following safety information carefully.
 Always perform automotive testing in a safe environment.
 If the VCI (Vehicle Communication Interface) device is not in use for a long
period of time, it is suggested to unplug the connector from vehicle’s DLC to
conserve battery power.
 Wear an ANSI-approved eye shield when testing or repairing vehicles.
 The vehicle shall be tested in a well-ventilated work area, as engines produce
various poisonous compounds (hydrocarbon, carbon monoxide, nitrogen
oxides, etc.)
 Do not connect or disconnect any test equipment while the ignition is on or

ii
LAUNCH X-431 PRO3S+ V2.0 User Manual

the engine is running.

 Put blocks in front of the drive wheels and never leave the vehicle unattended
while testing.
 Keep the tool dry, clean, free from oil, water or grease. Use a mild detergent
on a clean cloth to clear the outside of the equipment as necessary.
 Do not drive the vehicle and operate the tool at the same time. Any distraction
may cause an accident.
 Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or
hot engine parts.
 Before starting the engine, put the gear lever in the Neutral position (for
manual transmission) or in the Park (for automatic transmission) position to
avoid injury.
 To avoid damaging the tool or generating false data, please make sure the
vehicle battery is fully charged and the connection to the vehicle DLC (Data
Link Connector) is clear and secure.
 Automotive batteries contain sulfuric acid that is harmful to skin. In operation,
direct contact with the automotive batteries should be avoided. Keep the
ignition sources away from the battery at all times.

Precautions on Operating Vehicle’s ECU

 Do not disconnect battery or any wiring cables in the vehicle when the ignition
switch is on, as this could avoid damage to the sensors or the ECU.
 Do not place any magnetic objects near the ECU. Disconnect the power
supply to the ECU before performing any welding operations on the vehicle.
 Use extreme caution when performing any operations near the ECU or
sensors. Ground yourself when you disassemble PROM, otherwise ECU and
sensors can be damaged by static electricity.
 When reconnecting the ECU harness connector, be sure it is attached firmly,
otherwise electronic elements, such as ICs inside the ECU, can be damaged.

iii
LAUNCH X-431 PRO3S+ V2.0 User Manual

FCC Statement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

iv
LAUNCH X-431 PRO3S+ V2.0 User Manual

TABLE OF CONTENTS
1 INTRODUCTION .......................................................................................... 1
1.1 PRODUCT PROFILE .................................................................................. 1
1.2 PACKAGE LIST (ONLY FOR PASSENGER VEHICLE CONFIGURATION) ........... 2
1.2 PACKAGE LIST (ONLY FOR DIESEL & GASOLINE CONFIGURATION ) ............. 3
1.3 COMPONENTS & CONTROLS .................................................................... 4
1.3.1 Display tablet ................................................................................. 4
1.3.2 VCI connector (Only for Passenger Vehicle Configuration) ............ 6
1.3.2 VCI module (Only for Diesel & Gasoline Configuration) ................. 6
1.4 TECHNICAL PARAMETERS ........................................................................ 8
1.4.1 Display tablet ................................................................................. 8
1.4.2 VCI device (Only for Passenger Vehicle Configuration) ................. 8
1.4.2 VCI module (Only for Diesel & Gasoline Configuration) ................. 9

2 INITIAL USE ............................................................................................... 10

2.1 CHARGING THE TABLET ......................................................................... 10
2.2 POWER ON/OFF ..................................................................................... 10
2.2.1 Power on ...................................................................................... 10
2.2.2 Power off ...................................................................................... 10
2.3 BASIC GESTURES .................................................................................. 11
2.4 SCREEN LAYOUT ................................................................................... 11
2.5 ADJUST BRIGHTNESS ............................................................................ 11
2.6 CHANGE SYSTEM LANGUAGE ................................................................. 12
2.7 SET STANDBY TIME ............................................................................... 12

3 NETWORK SETUP .................................................................................... 13

3.1 CONNECT TO A W I-FI NETWORK ............................................................ 13
3.2 DISCONNECT FROM A W I-FI NETWORK................................................... 13

4 GETTING STARTED .................................................................................. 14

4.1 REGISTER & DOWNLOAD DIAGNOSTIC SOFTWARE .................................. 14
4.2 JOB MENU ............................................................................................ 17

v
LAUNCH X-431 PRO3S+ V2.0 User Manual

4.3 DIAGNOSTICS TOOLBAR......................................................................... 18

4.4 CONNECTIONS ...................................................................................... 19
4.4.1 Preparation .................................................................................. 19
4.4.2 DLC location ................................................................................ 19
4.4.3 Vehicle connection (For Passenger Vehicle Configuration) .......... 19
4.4.3 Vehicle connection (Only for Diesel & Gasoline Configuration) .... 21

5 DIAGNOSE................................................................................................. 22
5.1 INTELLIGENT DIAGNOSE......................................................................... 22
5.2 LOCAL DIAGNOSE .................................................................................. 26
5.2.1 Health Report (Quick Test) ........................................................... 32
5.2.2 System Scan ................................................................................ 35
5.2.3 System Selection ......................................................................... 36
5.3 REMOTE DIAGNOSE ............................................................................... 47
5.3.1 Interface Layout ........................................................................... 47
5.3.2 Add Friends .................................................................................. 48
5.3.3 Start Instant Messaging ................................................................ 49
5.3.4 Launch Remote Diagnosis (Device-To-Device) ............................ 51
5.3.5 Launch Remote Diagnosis (Device-To-PC) .................................. 54
5.4 FEEDBACK ............................................................................................ 56
5.5 DIAGNOSTIC HISTORY ........................................................................... 57
5.6 MY REPORT .......................................................................................... 58

6 SPECIAL (RESET) FUNCTION .................................................................. 60

6.1 OIL RESET SERVICE .............................................................................. 61
6.2 ELECTRONIC PARKING BRAKE RESET ..................................................... 61
6.3 STEERING ANGLE CALIBRATION ............................................................. 62
6.4 ABS BLEEDING ..................................................................................... 62
6.5 TIRE PRESSURE MONITOR SYSTEM RESET ............................................. 62
6.6 GEAR LEARNING ................................................................................... 62
6.7 IMMO SERVICE..................................................................................... 63
6.8 INJECTOR CODING ................................................................................. 63

vi
LAUNCH X-431 PRO3S+ V2.0 User Manual

6.9 BATTERY MAINTENANCE SYSTEM RESET ................................................ 64

6.10 DIESEL PARTICULATE FILTER (DPF) REGENERATION ............................ 64
6.11 ELECTRONIC THROTTLE POSITION RESET ............................................ 65
6.12 GEARBOX MATCHING .......................................................................... 65
6.13 AFS (ADAPTIVE FRONT -LIGHTING SYSTEM) RESET ............................... 65
6.14 SUNROOF INITIALIZATION ..................................................................... 65
6.15 SUSPENSION CALIBRATION .................................................................. 65

7 SOFTWARE UPDATE ................................................................................ 66

7.1 UPDATE DIAGNOSTIC SOFTWARE & APP ................................................ 66
7.2 UPDATE FREQUENTLY USED SOFTWARE ................................................ 67
7.3 RENEW SOFTWARE SUBSCRIPTION ........................................................ 68

8 USER INFO ................................................................................................ 70

8.1 VCI ...................................................................................................... 70
8.2 VCI MANAGEMENT (ONLY FOR PASSENGER VEHICLE CONFIGURATION) ... 70
8.2 VCI MANAGEMENT (ONLY FOR DIESEL & GASOLINE CONFIGURATION) ..... 70
8.3 ACTIVATE VCI ....................................................................................... 72
8.4 FIRMWARE FIX ...................................................................................... 73
8.5 DATA STREAM SAMPLE.......................................................................... 73
8.6 MY ORDER ........................................................................................... 73
8.7 SUBSCRIPTION RENEWAL CARD ............................................................. 73
8.8 PROFILE ............................................................................................... 74
8.9 CHANGE PASSWORD ............................................................................. 74
8.10 SETTINGS ........................................................................................... 74
8.10.1 Units ........................................................................................... 74
8.10.2 Shop Information ........................................................................ 75
8.10.3 Printer Set .................................................................................. 75
8.10.4 Orientation ................................................................................. 78
8.10.5 Clear Cache ............................................................................... 79
8.10.6 About .......................................................................................... 79
8.10.7 Diagnostic Software Auto Update ............................................... 79

vii
LAUNCH X-431 PRO3S+ V2.0 User Manual

8.10.8 Device Account Management ..................................................... 79

8.10.9 Login/Logout .............................................................................. 81
8.11 DIAGNOSTIC SOFTWARE CLEAR ........................................................... 81

9 TPMS.......................................................................................................... 82

10 FAQ .......................................................................................................... 83

viii
LAUNCH X-431 PRO3S+ V2.0 User Manual

1 Introduction

1.1 Product Profile

X-431 PRO3S+ V2.0 inherits from LAUNCH’s advanced diagnosing technology
and is characterized by covering a wide range of vehicles, featuring powerful
functions, and providing precise test result. Through the simple Bluetooth (for
Passenger Vehicle configuration) / Bluetooth or Wi-Fi communication (for Diesel
& Gasoline configuration) between VCI (Vehicle Communication Interface)
device and the display tablet, it achieves full car model and full system vehicle
trouble diagnosis, which include Reading DTCs, Clearing DTCs, Reading Data
Stream, Actuation Test and Special Functions.
It supports the following functions:
 Intelligent Diagnose: This module allows you to use the VIN information of the
currently identified vehicle to access its data (including vehicle information,
historical diagnostic records) from the cloud server to perform quick test.
 Local Diagnose: Follow the on-screen prompts to start diagnostic session
step by step. Diagnosis functions include: Read DTCs, Clear DTCs, Read
Data Stream, Special Functions etc.
 Remote Diagnose: This option aims to help repair shops or technicians
launch instant messaging and remote diagnosis, making the repair job getting
fixed faster.
 Reset: All kinds of common maintenance and reset items including Oil lamp
reset, DPF regeneration, ABS bleeding etc. can be done.
 TPMS: This module allows you to configure the tablet as TPMS activation &
diagnostic tool, which provides the ability to trigger TPMS sensor, program
TPMS sensor, perform the relearning procedure. It needs to work with the
X-431 TSGUN device (sold separately).
 One-click Update: Lets you update your diagnostic software online.
 Diagnostic History: This function provides a quick access to the tested
vehicles and users can choose to view the test report or resume from the last
operation, without starting from scratch.
 Feedback: Enables you to submit the vehicle issue to us for analysis and
troubleshooting.

1
LAUNCH X-431 PRO3S+ V2.0 User Manual

 Vehicle Coverage: Quick dial to view the vehicle models that the tool covers.

1.2 Package List (Only for Passenger Vehicle Configuration)

Common accessories are same, but for different destinations, the accessories
(such as diagnostic software, testing connectors) may vary. Please consult from
the local agency or check the package list supplied with this tool together.

No. Item Descriptions Qt.

1 Display tablet Indicates the test result. 1

Collects the vehicle data and sends it

2 VCI connector 1
to the tablet for analysis.

OBD II extension To connect the VCI connector to the

3 1
cable OBD II vehicle’s DLC.

A piece of paper bearing the product

4 Password envelope Serial Number and Activation Code for 1
product registration.

5 Power adaptor For charging the tablet via AC outlet. (Optional)

Battery clamps To supply power to the non-16pin

6 (Optional)
cable connector from the vehicle’s battery.

To supply power to the non-16pin

Cigarette lighter
7 connector from the vehicle’s cigarette (Optional)
cable
lighter receptacle.

8 USB cable 1

For connecting the VCI connector and

9 OBD I adaptor box (Optional)
non-16pin adaptor cable.

Non-16pin adaptor To connect to the vehicle equipped

10 (Optional)
cable kit with non-OBD II management system.

2
LAUNCH X-431 PRO3S+ V2.0 User Manual

1.2 Package List (Only for Diesel & Gasoline Configuration)

Common accessories are same, but for different destinations, the accessories
(such as diagnostic software, testing connectors) may vary. Please consult from
the local agency or check the package list supplied with this tool together.

No. Item Descriptions Qt.

The central processor and monitor

1 Display tablet for analyzing vehicle data and 1
showing test results.

A device for accessing vehicle live

2 VCI module 1
data.

A piece of paper bearing Product

Password
3 S/N and Activation Code, which is 1
envelope
required for your registration.

To connect the VCI module to

4 Diagnostic cable 1
vehicle’s DLC.

To supply power to the VCI module

Cigarette lighter
5 through connection to cigarette (optional)
cable
lighter receptacle.

To supply power to the VCI module

Battery clamps
6 through connection to vehicle’s (optional)
cable
battery.

A adaptor cable for connecting

OBD I adaptor
7 non-16pin connector of passenger (optional)
cable
vehicle.

To charge the tablet through

8 Power adaptor 1
connection to AC outlet.

To connect the VCI module and

USB cable with
9 diagnostic tool to perform vehicle 1
B-shaped terminal
diagnosis.

3
LAUNCH X-431 PRO3S+ V2.0 User Manual

For different vehicle diagnostic

socket, it may be necessary to use
Non-16pin
one of the adaptor cables included
adaptor cable kit
10 within the kit. (optional)
for passenger
vehicles For detailed non-16pin adaptor
cables, please check the package
box.

Non-16pin
For detailed non-16pin adaptor
adaptor cable kit
11 cables, please check the package (optional)
for commercial
box.
vehicles

1.3 Components & Controls

There are two main components to the diagnostic system:
 Display Tablet – the central processor and monitor for the system (See
Chapter 1.3.1).

 VCI Device – the device for accessing vehicle data (See Chapter 1.3.2).

1.3.1 Display tablet

The tablet acts as the central processing system, which is used to receive and
analyze the live vehicle data from the VCI device and then output the test result.

4
LAUNCH X-431 PRO3S+ V2.0 User Manual

1 LCD screen Indicates the test results.

In Off mode, press it for 3 seconds to turn the

tablet on.
In On mode:
 Press it once to activate the LCD if the LCD is
off.
2 POWER key
 Press it once to turn off the LCD if the LCD
lights up.
 Press and hold it for 3 seconds to turn it off.
 Press and hold it for 8 seconds to perform
forced shutdown.

3 Volume +/- Adjusts the system volume.

4 Speakers

5 Front camera

USB/Charging  To connect to AC outlet for charging.

6
port  To connect to PC for data exchange.

7 Microphone

8 Rear camera

5
LAUNCH X-431 PRO3S+ V2.0 User Manual

Flip it out to any angle and work comfortable at

9 Adjustable stand
your desk, or hang it on steering wheel.

1.3.2 VCI connector (Only for Passenger Vehicle Configuration)

The VCI works as a vehicle communication interface device, which is used to
connect to the vehicle’s DLC (Data Link Connector) socket directly or via OBD II
extension cable to read the vehicle data and then send it to the tablet via
Bluetooth.

OBD-16 diagnostic
1 Connects to vehicle’s OBD II DLC port.
connector

 It illuminates red when the VCI device is

connected to the vehicle’s DLC.
2 Mode indicator
 Blue indicates the VCI device is working in
wireless (BT) communication mode.

1.3.2 VCI module (Only for Diesel & Gasoline Configuration)

Compatible with commercial & passenger vehicles, the VCI module works as a
vehicle communication interface device. It is used to read the vehicle data and

6
LAUNCH X-431 PRO3S+ V2.0 User Manual

then send it to the tablet via Bluetooth/Wi-Fi communication. The LEDs enable
you to easily identify the working status of the module.

1 DC-IN power jack Connects the power adaptor.

2 Diagnostic socket Connects the diagnostic cable.

It is defined as follows:
 Vehicle: While communicating with the
vehicle, the indicator lights up and flashes.
Otherwise, it will not illuminate.
 Power: It illuminates solid red when the
3 LEDs module is powered on.
 BT: Blue indicates the module is working in
Bluetooth mode.
 I/O: It lights up when the module is
connected to the diagnostic tool via USB
cable (Currently disabled and only reserved for

7
LAUNCH X-431 PRO3S+ V2.0 User Manual

subsequent function extension).

 Wireless: It lights up when the module works
as a Wi-Fi hotspot or wireless adaptor.

Currently disabled and only reserved for

4 USB port
subsequent function extension.

1.4 Technical Parameters

1.4.1 Display tablet

Operating system Android

Memory 3GB

Storage 32GB

10.1 inch FHD IPS capacitive touch screen with

Screen
a resolution of 1920 x 1200 pixels

Front-facing 5.0MP camera + rear-facing 8.0MP

Camera
camera

 Wi-Fi (802.11a/b/g/n/ac)
Connectivity
 Bluetooth

Working temperature 0℃ ~ 50℃

Storage temperature -20℃ ~ 70℃

1.4.2 VCI device (Only for Passenger Vehicle Configuration)

Working voltage 9 ~18V

Working temperature 0℃ ~ 50℃

Relative humidity 20% ~ 90%

8
LAUNCH X-431 PRO3S+ V2.0 User Manual

1.4.2 VCI module (Only for Diesel & Gasoline Configuration)

Working voltage DC 9 ~36V

Power consumption ≤ 3W

Communication Via Bluetooth/Wi-Fi or USB connection

Working temperature 0 to 50℃

9
LAUNCH X-431 PRO3S+ V2.0 User Manual

2 Initial Use

2.1 Charging the Tablet

1. Plug one end of the included charging port of the tool, and the other end to
the power adaptor.
2. Connect the other end to the AC outlet.

If appears on the screen, it indicates it is being charged. If the logo changes

into , it indicates that the battery is fully charged. Unplug the power adaptor
from the tablet.

Caution: Please use the included power adaptor to charge your tool. No
responsibility can be assumed for any damage or loss caused as a result of using power
adaptors other than the one supplied.

Notes:
 If the battery remains unused for a long period of time or the battery is completely
discharged, it is normal that the tool will not power on while being charged. Please
charge it for a period of 5 minutes and then turn it on.
 While the tablet has low battery, a beep will sound. If it is very low, the tablet will be
switched off automatically.

2.2 Power on/off

2.2.1 Power on
Press [POWER] to turn the tool on.

Note: If it is the first time you have used this tool or the tool remains idle for a
long period of time, the tool could fail to turn on. Please charge the tool for a minimum
of 5 minutes and attempt to turn on again.

2.2.2 Power off

Press [POWER] for 3 seconds, an option menu will pop up on the screen. Tap
Power off to turn the tool off.

10
LAUNCH X-431 PRO3S+ V2.0 User Manual

2.3 Basic Gestures

Single-tap: To select an item or launch a program.

Double-tap: To zoom in so that the text on a webpage appears in a

column that fits your device’s screen.

Long press: Tap and hold on the current interface or area until a
contextual menu pops up on the screen, and then release it.

Slide: To jump to different pages.

Drag: Tap the application icon and drop it to other location.

Spread apart/pinch together: To zoom in manually, place two

fingers on the screen and then spread them apart. To zoom out,
place two fingers apart on the screen and then pinch them together.

2.4 Screen Layout

There are five on-screen buttons available on the bottom of the screen.

BACK Tap it to return to the previous screen.

HOME Tap it to navigate to the Android’s home screen.

Recent Apps Tap it to view the recently launched applications.

Screenshot Tap it to capture the current screen.

2.5 Adjust Brightness

Note: Reducing the brightness of the screen is helpful to conserve the battery
power.
1. On the home screen, tap Settings -> Display -> Brightness level.

11
LAUNCH X-431 PRO3S+ V2.0 User Manual

2. Drag the slider to adjust it.

2.6 Change System Language

The tool supports multiple system languages. To change the language of the
tool, please do the following:
1. On the home screen, tap Settings -> System -> Language & input ->
Languages.
2. Tap Add a language, and then choose the desired language from the list.
3. Tap and hold the desired language and drag it to the top of the screen and
then release it, the system will change into the target language.

2.7 Set Standby Time

If no activities are made within the defined standby period, the screen will be
locked automatically and the system enters sleep mode to save power.
1. On the home screen, tap Settings -> Display -> Advanced -> Sleep.
2. Choose the desired sleep time.

12
LAUNCH X-431 PRO3S+ V2.0 User Manual

3 Network Setup

Note: If you don’t need to use Wi-Fi for a while, you can turn it off to conserve
battery life.
The tablet has built-in Wi-Fi that can be used to get online. Once you’re online,
you can register your tool, surf the Internet, get apps, send email, launch the
remote diagnosis, and check for software updates etc.

3.1 Connect to a Wi-Fi Network

1. On the home screen, tap Settings -> Network & Internet -> WLAN.
2. Slide the Wi-Fi switch to ON, the tablet starts searching for available wireless
networks.
3. Select a wireless network,
 If the chosen network is open, the tablet will connect automatically.
 If the selected network is encrypted, a network password will need to be
entered.
4. When Connected appears, it indicates the Wi-Fi connection is complete.

Note: When Wi-Fi is not required, this should be disabled to conserve battery
power.
Once it is connected successfully, tap the desired Wi-Fi network from the list to
view its name, link speed, security type, IP address etc.
When this tool is in range, it will connect to the previously linked network
automatically.

3.2 Disconnect From a Wi-Fi Network

1. On the home screen, tap Settings -> Network & Internet -> WLAN.
2. Tap the network with a Connected status, then tap Disconnect.

13
LAUNCH X-431 PRO3S+ V2.0 User Manual

4 Getting Started

4.1 Register & Download Diagnostic Software

For new users, please follow the operation chart shown as below to get familiar
with and start using this tool.

Tap the application icon on the home screen to launch it, and then tap Login to
enter the login interface of diagnosis software.

(If you are a new user, follow A to proceed.)

(If you have registered to be a member, go to B to login the system directly.)
(In case you forgot password, refer to C to reset a new password.)
A. If you are a new user, tap New Registration to enter the sign-up page.

14
LAUNCH X-431 PRO3S+ V2.0 User Manual

In the above figure, fill in the information in each field (Items with * must be filled).
After inputting, tap Register, the following screen will appear:

Input the Serial Number and Activation Code, which can be found in the
password envelope.

Product SN Product SN

Activation code

15
LAUNCH X-431 PRO3S+ V2.0 User Manual

Note: To exit and activate it later, tap Skip. In this case, you can activate your VCI
module by tapping User Info -> Activate VCI.
Tap Activate to finish your registration.

To download the diagnostic software, tap Yes to enter the update page.
Tap No to download and install it later.
After download is complete, the system will install the software package
automatically.

Note: In process of download, please make sure it is properly connected to the

WLAN network. It may take several minutes to finish it, please be patient to wait.
B. If you have registered to be a member, input your name and password, and
then tap Login to enter the main menu screen directly.
Note: The tablet has an auto-save function. Once the username and password are
correctly entered, the system will automatically store it. Next time you login the system,
you will not be asked to input the account manually.
16
LAUNCH X-431 PRO3S+ V2.0 User Manual

C. If you forgot the password, tap Retrieve password and then follow
on-screen instructions to set a new password.

4.2 Job Menu

It mainly includes the following items:

Name Description

This module allows you to obtain vehicle data from the

cloud server to perform quick test via reading VIN,
Intelligent which provides a perfect solution to various defects
Diagnose resulting from step-by-step menu selection. In addition,
user can also check the historical repair records online
through this module.

Local Diagnose To diagnose a vehicle manually.

To perform all kinds of common repair & maintenance

Reset items, including electronic throttle position reset, ABS
bleeding, oil lamp reset etc.

This helps repair shops or mechanics to diagnose a

Remote Diagnose remote vehicle, and launch instant messages, allowing
for improved efficiency and faster repairs.

This module allows you to configure the tablet as TPMS

activation & diagnostic tool, which provides the ability to
TPMS trigger TPMS sensor, program TPMS sensor, perform
the relearning procedure. It needs to work with the
X-431 TSGUN device (sold separately).

Software Update To update vehicle diagnostic software and APK.

Generally once a vehicle diagnosis is performed, the

tablet will automatically save every details of diagnostic
Diagnostic History process. This function provides a quick access to the
tested vehicles and users can resume from the last
operation, without the necessity of starting from scratch.

Feedback To feed back the recent 20 diagnostic logs to us for

17
LAUNCH X-431 PRO3S+ V2.0 User Manual

issue analysis.

Allows you to manage the saved diagnostic reports and

Report
recorded data.

This module enables you to subscribe some extra

Mall software or service functions that are not integrated in
the tool online.

Vehicle Coverage To view all the vehicle models that the tool covers.

Abundant maintenance data are available, which helps

Maintenance repair professionals diagnose and repair vehicles
efficiently, accurately and profitably.

To manage VCI, fix firmware, revise personal

User Info information, change password, app settings and logout
etc.

Includes product manual, FAQ, some frequently used

Other Modules
apps and tablet system settings.

4.3 Diagnostics Toolbar

The diagnostics toolbar contains a number of buttons that allow you to print the
displayed data or make other controls. It is displayed on the upper right corner of
the screen and goes through the whole diagnostic session. The table below
provides a brief description for the operations of the diagnostics toolbar buttons:

Name Button Description

Home Returns to Job menu.

Tap to print the current screen content out via

external printer. The printer needs to be
Print
configured separately. For details on printer
setting, refer to Chapter 8.10.3.

18
LAUNCH X-431 PRO3S+ V2.0 User Manual

Exit To exit the diagnostic application.

4.4 Connections
4.4.1 Preparation
Normal testing conditions
 Turn on the vehicle power supply.
 Vehicle battery voltage range should be 9-14V or 18V~30V.
 Throttle should be closed at its close position.

4.4.2 DLC location

The DLC (Data Link Connector or Diagnostic Link Connector) is typically a
standard 16-pin connector where diagnostic code readers interface with the
vehicle’s on-board computer. The DLC is usually located 12 inches from the
center of the instrument panel (dash), under or around the driver’s side for most
vehicles. If DLC is not located under dashboard, a label should be there telling
location. For some Asian and European vehicles, the DLC is located behind the
ashtray and the ashtray must be removed to access the connector. If the DLC
cannot be found, refer to the vehicle’s service manual for the location.

4.4.3 Vehicle connection (For Passenger Vehicle Configuration)

The method used to connect the VCI device to a vehicle’s DLC depends on the
vehicle’s configuration as follows:

19
LAUNCH X-431 PRO3S+ V2.0 User Manual

 A vehicle equipped with an OBD II management system supplies both

communication and 12V power through a standardized DLC.
 A vehicle not equipped with an OBD II management system supplies
communication through a DLC connection, and in some cases supplies 12V
power through the cigarette lighter receptacle or a connection to the vehicle
battery.
Follow the steps mentioned below to connect OBD II vehicle:
1. Locate vehicle’s DLC socket.
2. Plug the VCI device into the vehicle’s DLC socket (It is suggested to use the
OBD II extension cable to connect the VCI device and DLC socket).

3. Choose one of the two ways to obtain power from:

A. Power adaptor: Connect one end of the included power adaptor to
charging port of the tablet, and the other end to AC outlet.
B. Internal battery pack

For non-OBDII vehicle, proceed as follows:

1. Locate vehicle’s DLC socket.
2. Select the corresponding non-16pin connector.
3. Plug the non-16pin end of the connector into the DLC socket, then connect
the other end to the OBD I adaptor, and then tighten the captive screws.
4. Connect the other end of the adaptor to the included VCI device.
5. If the pin of the DLC is damaged or has insufficient power, please follow the
either of the following methods to proceed:
A. Cigarette Lighter cable (optional): Connect one end of the cigarette lighter
cable to vehicle’s cigarette lighter receptacle, and the other end to the power
jack of OBD I adaptor.

20
LAUNCH X-431 PRO3S+ V2.0 User Manual

B. Battery Clamps Cable: Connect one end of the battery clamps cable to
vehicle’s battery, and the other end to the power jack of OBD I adaptor.

4.4.3 Vehicle connection (Only for Diesel & Gasoline Configuration)

The method used to connect the VCI module to a vehicle’s DLC depends on the
vehicle’s configuration as follows:
A. OBD II Vehicle Connection: Plug one end of the diagnostic cable into the
vehicle’s DLC, and the other end into the diagnostic socket of the VCI module,
and then tighten the captive screws.

B. Non-OBD II Vehicle Connection: For vehicles with non-OBD II diagnostic

socket, a non-16pin connector (adaptor cable) is required.

Notes:
a). For commercial vehicles, refer to the above connection method to proceed.
b). For passenger vehicles, replace the “Non-16pin connector” with “OBD I adaptor” +
“non-16pin connector (for passenger vehicles)”. Other connections shall also apply.

21
LAUNCH X-431 PRO3S+ V2.0 User Manual

5 Diagnose

5.1 Intelligent Diagnose

Through wireless communication between the display tablet and VCI, you can
easily get the VIN (Vehicle Identification Number) information of the currently
identified vehicle. Once the VIN is successfully identified, the system will retrieve
it from the remote server and then guide you to vehicle information page without
the necessity of step-by-step manual menu selection.
The vehicle information page lists all historical diagnostic records of the vehicle,
which lets the technician have a total command of the vehicle faults. In addition,
a quick dial to local diagnose and diagnostic function are also available on this
page for reducing the roundabout time and increasing productivity.

Notes:
• Before using this function, please make sure the VCI is properly connected to the
vehicle’s DLC. For detailed connection, see Chapter 4.4.3.
• A stable network connection is required for this function.
Follow the steps below to proceed.
1. Tap Intelligent Diagnose on the Job menu.

Note: If the VCI is not paired up with the tablet before doing this step, the following
prompt message will appear:

22
LAUNCH X-431 PRO3S+ V2.0 User Manual

If the VCI was once used with other devices, you need to cancel the pairing of the VCI
first: On the Android’s home screen, tap Settings -> Bluetooth -> Choose the desired
VCI from the Paired list. Tap , and then tap FORGET to unpair it.
Tap Scan to start searching for the VCI and pairing up with it.
2. Once pairing is complete, the tablet starts reading the vehicle VIN.
A. If the VIN can be found from the remote server database, the following
screen will appear:

• Tap Diagnostic to start a new diagnostic session.

• Tap Scan History to view its historical repair record. If there are records
available, it will be listed on the screen in sequence of date. If no records
exist, the screen will show No Record.

23
LAUNCH X-431 PRO3S+ V2.0 User Manual

• Tap View record to view the details of the current diagnostic report.
• To perform other functions, tap Quick access to directly go to the function
selection screen. Choose the desired one to start a new diagnostic
session.
B. If the tablet failed to access the VIN information, the screen will display as
below:

• Tap the input field to directly, tap OK. If the VIN exists on the remote server,
the system will enter the diagnostic function selection screen.
• Tap to launch the VIN recognition module.

24
LAUNCH X-431 PRO3S+ V2.0 User Manual

Place the VIN inside the viewfinder rectangle to scan it. The most
recognizable location for this number is in the top left corner on the
vehicle’s dashboard. Other locations include the driver’s door or post, and
the firewall under the hood.

• Tap to switch the display mode of the screen.

• Tap to turn the camera flash on.

• Tap to choose it from the record list if the VIN of the vehicle has
been scanned before.

• Tap to input the VIN manually if the tablet has failed to identify the
VIN of the vehicle.
• Tap to scan the VIN barcode. If the VIN barcode cannot be
recognized, please manually input the VIN.

• Tap to scan the VIN character. If the VIN character cannot be

recognized, please manually input the VIN.
Note: In general, vehicle identification numbers are standardized - all
contain 17 characters. VIN characters may be capital letters A through Z and
numbers 1 through 0; however, the letters I, O and Q are never used in order to
avoid mistakes of misreading. No signs or spaces are allowed in the VIN.
After scanning, the screen automatically displays the result.

25
LAUNCH X-431 PRO3S+ V2.0 User Manual

• If the VIN scanned is incorrect, tap the result field to modify it and then tap
OK.
• To scan it again, tap REPEAT.
If the VIN exists on the remote server, the system will enter the diagnostic
function selection screen.

5.2 Local Diagnose

In this mode, you need to execute the menu-driven command and then follow
the on-screen instruction to proceed.
Tap Local Diagnose to enter the vehicle selection page.

2 approaches are provided for you to access the vehicle diagnostic software.
Choose any one of the following ways:
1. VIN SCAN enables you to access it more quickly.
Tap VIN Scan, the following screen will appear:

26
LAUNCH X-431 PRO3S+ V2.0 User Manual

In this case, camera scan and enter VIN are available.

A. Camera Scan: In this mode, the VCI should be connected to the vehicle’s
DLC first, and then a Bluetooth communication should be established
between the tablet and the VCI.
Tap Camera Scan, a screen similar to the following will appear:

Place the VIN inside the viewfinder rectangle to scan it. The most
recognizable location for this number is in the top left corner on the vehicle’s
dashboard. Other locations include the driver’s door or post, and the firewall
under the hood.
• Tap to switch the display mode of the screen.

• Tap to turn the camera flash on.

27
LAUNCH X-431 PRO3S+ V2.0 User Manual

• Tap to choose it from the record list if the VIN of the vehicle has been
scanned before.

• Tap to input the VIN manually if the tablet has failed to identify the
VIN of the vehicle.
• Tap to scan the VIN barcode. If the VIN barcode cannot be
recognized, please manually input the VIN.

• Tap to scan the VIN character. If the VIN character cannot be

recognized, please manually input the VIN.
Note: In general, vehicle identification numbers are standardized - all contain
17 characters. VIN characters may be capital letters A through Z and numbers 1
through 0; however, the letters I, O and Q are never used in order to avoid mistakes
of misreading. No signs or spaces are allowed in the VIN.
After scanning, the following screen will appear.

If the VIN scanned is incorrect, tap the result field to modify it and then tap OK.
If the VIN exists on the remote server, the system will navigate to the
diagnostic function selection screen directly.
Tap the desired option to perform the corresponding diagnostic function.

Note: Before using this function, the corresponding diagnostic software and
Auto search file need to be downloaded on your tool first while downloading the
diagnostic software.
B. INPUT VIN: In this mode, you can input the vehicle VIN manually. In general,
the vehicle identification numbers are standardized - all contain 17
characters. VIN characters may be capital letters A through Z and numbers 1

28
LAUNCH X-431 PRO3S+ V2.0 User Manual

through 0; however, the letters I, O and Q are never used in order to avoid
mistakes of misreading. No signs or spaces are allowed in the VIN.
Tap Enter VIN, the following screen will appear.

Input the VIN, and tap OK, the tablet will automatically identify the vehicle
model and directly navigate to the diagnostic function selection menu.
2. Tap a corresponding diagnostic software logo, and then follow the on-screen
instruction to access the diagnostic software.
Take Demo (Version 15.21) as an example to demonstrate how to diagnose a
vehicle.
1). Select diagnostic software version: Tap the DEMO to go to Step 2.

On-screen Buttons:

29
LAUNCH X-431 PRO3S+ V2.0 User Manual

Vehicle Coverage: Tap to view the vehicle models that the current diagnostic
software covers.
What’s new: Tap to view the optimized items and enhancements.
Introduction: Tap to check the software function list.
Note: Tap to read some precautions on using the current diagnostic software.
Search Bluetooth: Tap to search for the available VCI. After the VCI is
successfully activated, it will be bound to the user account and paired with the
tablet automatically.
Note: No Bluetooth connection is required for DEMO program.
OK: Tap it to go to next step.
2). Select vehicle model (varies with different versions): Select the desired
vehicle model. Here we take Ford for example to demonstrate how to
diagnose a vehicle.

3). Read vehicle information: After reading the vehicle information, double check
if the vehicle information is correct or not. If yes, tap Yes to continue.

30
LAUNCH X-431 PRO3S+ V2.0 User Manual

4). Select test item: Select the desired test item to proceed.

5). Turn the ignition key to ON: Set the ignition switch to on.

31
LAUNCH X-431 PRO3S+ V2.0 User Manual

5.2.1 Health Report (Quick Test)

This function varies from vehicle to vehicle. It enables you to quickly access all
the electronic control units of the vehicle and generate a detailed report about
vehicle health.
On the test item selection screen, tap Health Report and turn on the ignition
switch, the system will start scanning the ECUs. Once the scanning process is
complete, the following screen will appear:

The tested system with fault code appears in red and the system with OK
displays in black (normally).

Note: Diagnostic Trouble Codes or Fault Codes can be used to identify which
engine systems or components that are malfunctioning. Never replace a part based only
on the DTC definition. Retrieving and using DTCs for troubleshooting vehicle

32
LAUNCH X-431 PRO3S+ V2.0 User Manual

operation is only one part of an overall diagnostic strategy. Follow testing procedures
(in vehicle’s service manual), instructions and flowcharts to confirm the locations of the
problem.
On-screen Buttons:

Enter: Tap to enter the diagnostic function selection screen.

(Search): Highlight certain diagnostic trouble code and tap it to retrieve it in
the search engine.
Report: Tap to save the diagnostic result as a health report.

Note: Diagnostic report is classified into three categories: Pre-Repair report,

Post-Repair report and Diagnostic Scan. No matter which type you saved the report as,
the report type will be appended as a tag on the upper right corner of the diagnostic
report for easier identification.
Tap to select the report type from the option list and input the required
information, and then tap OK.
Note: To facilitate the comparison of the pre-repair and post-repair reports and get
accurate test result, please make sure you saved the right type of the diagnostic report.
To save the report as a common diagnostic report, select Diagnostic Scan.

33
LAUNCH X-431 PRO3S+ V2.0 User Manual

Note: For workshop information, tap the input box to enter it. Alternatively you
can also set it in User Info -> Settings -> Shop Information.
Once you configured the information, it will be automatically generated every time you
saved the diagnostic report. All vehicle and workshop information will be appended as
tags on the diagnostic report.
To ignore the workshop information, tap Skip to go to the report details screen.

On the report details screen, tap Save to save it. All diagnostic reports are saved
in Report -> Health Report.
Help: Tap to view the help information of the selected DTC item.
Compare Results: Tap to select the pre-repair report to compare. By
comparison of the pre- and post- repair reports, you can easily identify which

34
LAUNCH X-431 PRO3S+ V2.0 User Manual

DTCs are cleared and which remain unfixed.

• Post indicates DTC status of post-repair.

• Pre indicates DTC status of pre-repair.

Note: Before performing this function, please make sure that:

• You have saved a pre-repair report of the currently tested vehicle, and
• You have already made some repairs and service and cleared the DTCs after the
pre-repair reported is generated. Otherwise, no differences exist between the pre-
and post- repair reports.
Clear DTCs: Tap to clear the existing diagnostic trouble codes.

Note: Clearing DTCs does not fix the problem(s) that caused the code(s) to be set.
If proper repairs to correct the problem that caused the code(s) to be set are not made,
the code(s) will appear again and the check engine light will illuminate as soon as the
problem that cause the DTC to set manifests itself.

5.2.2 System Scan

This option allows you to quickly scan which systems are installed on the
vehicle.
On the test item selection screen, tap System Scan, the system start scanning
the systems. Once the scanning process is complete, the following screen will
appear.

35
LAUNCH X-431 PRO3S+ V2.0 User Manual

Tap the desired system to go to the diagnostic function selection screen. For
detailed operations on diagnostic function, please refer to Chapter 5.2.3.

5.2.3 System Selection

This option allows you to manually select the test system and function step by
step.
On the test item selection screen, tap System Selection, the screen displays as
follows:

Swipe the screen from the bottom to view the vehicle system on the next page.
Tap the target system (take ECM for example) to navigate to the diagnostic
function selection screen.

36
LAUNCH X-431 PRO3S+ V2.0 User Manual

Note: Different vehicle has different diagnostic menus.

A. Version Information
This function is used to read the version information of system mode, vehicle
VIN, software and ECU.

B. Read Fault Code

This function displays the detailed information of DTC records retrieved from the
vehicle’s control system.
Caution: Retrieving and using DTCs for troubleshooting vehicle operation is only
one part of an overall diagnostic strategy. Never replace a part based only on the DTC
definition. Each DTC has a set of testing procedures, instructions and flow charts that
must be followed to confirm the location of the problem. This information can be found
in the vehicle’s service manual.
On the diagnostic function selection screen, tap Read Fault Code, the screen
will display the diagnostic result.

37
LAUNCH X-431 PRO3S+ V2.0 User Manual

On-screen Buttons:
Freeze Frame: When an emission-related fault occurs, certain vehicle
conditions are recorded by the on-board computer. This information is referred
to as freeze frame data. Freeze frame data includes a snapshot of critical
parameter values at the time the DTC is set.
Help: Tap to view the help information.
Code Search: Tap to search for more information about the current DTC online.
Report: Tap to save the current data in text format. All reports are saved in
Report -> Health Reports.

C. Clear Fault Code

This function enables you to erase the codes from the vehicle after reading the
retrieved codes from the vehicle and certain repairs have been carried out.
Before performing this function, make sure the vehicle’s ignition key is in the ON
position with the engine off.
Clearing DTCs does not fix the problem(s) that caused the code(s) to be set. If
proper repairs to correct the problem that caused the code(s) to be set are not
made, the code(s) will appear again and the check engine light will illuminate as
soon as the problem that cause the DTC to set manifests itself.
On the diagnostic function selection screen, tap Clear Fault Code, the following
screen will appear.

38
LAUNCH X-431 PRO3S+ V2.0 User Manual

Tap YES, the system will automatically delete the currently existing trouble
code.
Note: After clearing, you should retrieve trouble codes once more or turn ignition
on and retrieve codes again. If there are still some trouble codes in the system, please
troubleshoot the code using a factory diagnosis guide, then clear the code and recheck.

D. Read Data Stream

This option lets you view and capture (record) real-time Live Data. This data
including current operating status for parameters and/or sensor information can
provide insight on overall vehicle performance. It can also be used to guide
vehicle repair.
Caution: If you must drive the vehicle in order to perform a troubleshooting
procedure, ALWAYS have a second person help you. Trying to drive and operate the
diagnostic tool at the same time is dangerous, and could cause a serious traffic accident.
Note: The real time (Live Data) vehicle operating information (values/status) that
the on-board computer supplies to the tool for each sensor, actuator, switch, etc. is
called Parameter Identification Data (PID).
On the diagnostic function selection screen, tap Read Data Stream, the
following screen will appear.

39
LAUNCH X-431 PRO3S+ V2.0 User Manual

On-screen Buttons:
Select Page: Tap to select all items of the current page.
Select All: Tap to select all items. To select certain data stream item, just check
the box before the item name.
Unselect: Tap to deselect all data stream items.
OK: Tap to confirm and jump to the next step.
After selecting the desired items, tap OK to enter the data stream reading page.

Notes:
1. If the value of the data stream item is out of the range of the standard (reference)
value, the whole line will display in red. If it complies with the reference value, it
displays in blue (normal mode).

40
LAUNCH X-431 PRO3S+ V2.0 User Manual

2. The indicator 1/X shown on the bottom of the screen stands for the current
page/total page number. Swipe the screen from the right/left to advance/return to the
next/previous page.

There are 3 types of display modes available for data viewing, allowing you to
view various types of parameters in the most suitable way.
 Value – This is the default mode which displays the parameters in texts and
shows in list format.
 Graph – Displays the parameters in waveform graphs.
 Combine – This option is mostly used in graph merge status for data
comparison. In this case, different items are marked in different colors.
On-screen Buttons:
Graph(Single): Tap to view the parameter in waveform graph.

• Min/Max: Tap to define the maximum / minimum value. Once the value
goes beyond the specified value, the system will alarm.
Graph: Tap to view the parameters in waveform graphs.

41
LAUNCH X-431 PRO3S+ V2.0 User Manual

• Combine: This option is mostly used in graph merge status for data
comparison. In this case, different items are marked in different colors
(maximum 4 items can be displayed on the same screen simultaneously).
If the graph is more than one page, swipe the screen from the left to jump
to the next page.

• Value: Switches the current graph display mode to the Value display
mode.
• Customize: Tap , a pull-down list of the data stream items appears on
the screen. Select / deselect the desired items, and then screen will
display / remove the waveforms corresponding to these items immediately.

42
LAUNCH X-431 PRO3S+ V2.0 User Manual

Compare Sample: Tap to select the sample DS file.

All the values you customized and saved in process of DS sampling will be
imported into the Standard Range (See below) column for your comparison.
Note: Before executing this function, you have to sample the values of data stream
items and save it as a sample Data Stream file.

43
LAUNCH X-431 PRO3S+ V2.0 User Manual

Report: Tap to save the current data in text format. All reports are saved in
Report -> Health Reports. For details on report operations, please refer to
Chapter 5.6.
Record: Tap to start recording diagnostic data. Recorded live data can serve as
valuable information to help you in troubleshooting of vehicle problems.

Tap to end recording and save it. The saved file follows the naming rule: It
begins with vehicle type, and then the product S/N and ends with record starting
time (To differentiate between files, please configure the accurate system time).
All diagnostic records can be replayed from Report -> Recorded Data.
Save Sample: This item enables you to customize the standard range of live
data stream items and save it as DS sample file. Each time you run the data
stream items, you can call out the corresponding sample data to overwrite the

44
LAUNCH X-431 PRO3S+ V2.0 User Manual

current standard range.

Tap it to start recording the sample data (*Note: Only data stream items with
measurement units will be recorded), the following screen will appear:

Once the recording process is complete, tap to stop it and navigate to the
data revision screen.

Tap the Min./Max. value to change it. After modifying all desired items, tap Save
to save it as a sample DS file. All DS files are stored in User Info -> Data
Stream Sample.

E. Actuation Test
This option is used to access vehicle-specific subsystem and component tests.
Available test vary by vehicle manufacturer, year, and model.

45
LAUNCH X-431 PRO3S+ V2.0 User Manual

During the actuation test, the display tablet outputs commands to the ECU in
order to drive the actuators, and then determines the integrity of the system or
parts by reading the ECU data, or by monitoring the operation of the actuators,
such as switching an injector between two operating states.
On the diagnostic function selection screen, tap Actuation Test, the following
screen will appear:

Simply follow the on-screen instructions and make appropriate selections to

complete the test.

Each time when an operation is successfully executed, Completed displays.

F. Special Function
In addition to amazing & powerful diagnostic function, the tool also features

46
LAUNCH X-431 PRO3S+ V2.0 User Manual

various reset functions, which varies from vehicle to vehicle.

5.3 Remote Diagnose

This option aims to help repair shops or technicians launch instant messaging
and remote diagnosis, making the repair job getting fixed faster.
Tap Remote Diagnose on the Job menu, the screen appears blank by default.

5.3.1 Interface Layout

1
2

3
5

1 Home button Tap it to navigate to the Job menu.

Directly input the registered username of the tool to start

2 Search bar searching, and then tap the desired one to add it into
your friend list.

Friend list
3 By default it appears blank.
display area

Once an incoming message reaches, a red dot will

4 Message tab
appear on the upper right corner of the tab.

5 Contact tab Tap to enter the friend list.

Tap to slide the switch to ON, the tool keeps online and
becomes accessible on the web client. In this case,
6 Remote switch
inform the technician of your product S/N, and he/she
will control your device remotely.

47
LAUNCH X-431 PRO3S+ V2.0 User Manual

5.3.2 Add Friends

Tap Contacts to enter the contact page. By default it appears blank.

In the search bar, input the partner’s username and tap Search next to the
search bar to starts searching from Launch’s golo business database.
The partner must be the users who have registered their Launch’s diagnostic
tools. They may be the following:
 Workshop
 Technician
 golo users
Once the result matches the keyword, the following screen will appear:

Here you can tap Remote Diagnose to launch remote diagnostics directly or
choose to add the partner into the Contacts list.
Tap the desired name from the list, the following screen will appear:

48
LAUNCH X-431 PRO3S+ V2.0 User Manual

Tap Add friend, the following dialog box will pop up on the screen:

Tap CONFIRM to send your request.

Once the partner receives the request, a beep will sound. Tap the Messages
tab:
• Once the partner agreed your request, he/she will automatically be listed in
the Contacts tab.
• If a technician sent you a friend request, you can tap Agree to confirm and
his/her name will appear in the friend list (Contact). Or tap Ignore to ignore
this request.

5.3.3 Start Instant Messaging

Note: The I/M (Instant Messaging) function is open to all users who had Launch’s
diagnostic tool equipped with this module.
After adding your friends, tap the desired one’s photo to enter the following
screen:

49
LAUNCH X-431 PRO3S+ V2.0 User Manual

Tap the input field and use the on-screen keyboard to enter the text message,
and then tap Send to send it.
Tap to send the voice message.
Tap to send the emoj.
Tap to call out more function options.

File: Choose diagnostic reports or local files to send.

Picture: Choose screenshots or pictures to send.
Remote Diagnostic: To start a remote diagnostic session. For details, refer to
Chapter 5.3.4.
Camera: Open camera to take pictures.
Tap Clear to delete all the partner’s dialog logs.

50
LAUNCH X-431 PRO3S+ V2.0 User Manual

5.3.4 Launch Remote Diagnosis (Device-To-Device)

The tool is allowed to initiate remote diagnosis with other diagnostic tools
(including but not limited to the X-431 PRO3S+ V2.0) of Launch family, which
are equipped with this module.
Note: Before performing this operation, please make sure the following no matter
which side sends the remote request:
 Turn on the vehicle power supply.
 Throttle should be in a closed position.
 The tool should be properly connected to the vehicle’s DLC and a successful
communication is required.
On the function option selection screen, tap Remote Diagnostic, the following
pull-down menu will appear:

These options are defined as follows:

Actions Results

Request to control the partner’s device remotely to

help him diagnose the vehicle.
Notes:
 Remote diagnosis has the same diagnostic steps as
Request control manual diagnosis.
remote device  In process of remote diagnosis, tap the button to
send a voice message.
 Once vehicle diagnosis is complete, a report will be
created. Input your comments on this report, and then
tap Send Report to send it to the partner.

51
LAUNCH X-431 PRO3S+ V2.0 User Manual

Tap “Request control remote device”

Wait for partner’s confirmation

Start connecting after request confirmed

Start Diagnosis

Generate diagnostic report

If you need support, just use this option to invite a

technician to perform a remote control on your tool.

Notes:
 Remote diagnosis has the same diagnostic steps as
Invite remote manual diagnosis.
diagnostic assistant  In process of remote diagnosis, tap the button to
send voice message.
 Once you received the report from the partner, tap
View Report to view details. All diagnostic reports are
saved in Report -> Remote Reports.

52
LAUNCH X-431 PRO3S+ V2.0 User Manual

Cancel To cancel this operation.

53
LAUNCH X-431 PRO3S+ V2.0 User Manual

5.3.5 Launch Remote Diagnosis (Device-To-PC)

Except that the remote diagnosis can be done between different Launch’s
diagnostic tools that come loaded with the module, user also can ask for remote
control from PC client technician.

Tap the Remote tab, the following screen will appear:

54
LAUNCH X-431 PRO3S+ V2.0 User Manual

1. Slide the switch Allow device to be connected to the WEB client remote
diagnostic device to ON so that the partner can find and connect to this
device while using the PC.
2. Notify the partner of the PC client website http://remote.x431.com. When the
partner accesses the link, the PC displays as below:

Note: Before processing remote diagnosis, please make sure the tool is
properly connected to the vehicle.

3. Tell the partner to input his own official technician account and password, and
then tap Login to navigate to the following figure.

55
LAUNCH X-431 PRO3S+ V2.0 User Manual

4. Tell the partner to check the box Serial number and enter the Serial Number
provided by you, and then tap Start remote diagnosis to control your device
remotely.
In process of remote diagnosis, please note the following things:
1) You are not suggested to execute any actions.
2) The partner is not allowed to save any diagnostic reports or records on
your tablet.
The operations in remote diagnosis are same as those in local diagnose. Once
the session is complete, a remote diagnostic report will be automatically
generated.

5.4 Feedback
This item allows you to feedback your diagnostic problems to us for analysis and
troubleshooting.
Tap Feedback, a pop-up message will appear:

56
LAUNCH X-431 PRO3S+ V2.0 User Manual

Tap Confirm, the following 3 options will be displayed on the left column of the
screen.
A. Feedback
Tap certain tested vehicle model to enter the feedback screen.
1) Tap Choose File to open the target folder and choose the desired diagnostic
logs.
2) Choose the failure type and fill in the detailed failure description in the blank
text box and telephone or email address. After inputting, tap Submit Result
to send it to us.
B. History
Tap it to view all diagnostic feedback records. Different process states are
marked with different colors.
C. Offline list
Tap it to display all diagnostic feedback logs which have not been submitted
successfully due to network failure. Once the tablet gets a stable network signal,
it will be uploaded to the remote server automatically.

5.5 Diagnostic History

Generally once a vehicle diagnosis is performed, the tool will record the every
details of diagnostic process. The History function provides direct access to the
previously tested vehicles and users can resume from the last operation, without
the necessity of starting from scratch.
Tap Diagnostic History on the Job menu, all diagnostic records will be listed on
the screen in date sequence.

57
LAUNCH X-431 PRO3S+ V2.0 User Manual

• Tap certain vehicle model to view the details of the last diagnostic report.
• To delete certain diagnostic history, select it and then tap Delete. To
delete all historical records, tap Select All and then tap Delete.
• Tap Quick access to directly navigate to the function selection page of
last diagnostic operation. Choose the desired option to proceed.

5.6 My Report
This option is used to view, delete or share the saved reports.
Tap Report on the Job menu, there are total 3 options available.
1. In case the DTC result is saved on Read Trouble Code page, the files will be
listed under Health Reports tab.
• To select certain report, check the box before the report. To select all reports,
tap Select All. To deselect all, tap Unselect.
• To share the report with others, select the desired one and then tap Share.
• Select the desired report and then tap Delete to delete it.
• To revise the filename of the report, tap Rename.
2. Remote Reports lists all diagnostic reports generated in process of remote
diagnosis.
3. If user records the running parameters while reading data stream, it will be
saved as .x431 file and appear under Recorded Data tab.
Tap the desired one to enter. Select the desired data stream items and tap

58
LAUNCH X-431 PRO3S+ V2.0 User Manual

Confirm to jump to the playback page.

On-screen Buttons:
Graph – displays the parameters in waveform graphs.
Value – this is the default mode which displays the parameters in texts and
shows in list format.
Combine – this option is mostly used in graph merge status for data comparison.
In this case, different items are marked in different colors.
Frame Playback – plays back the recorded data stream items frame by frame.
Once it is in frame playback mode, this button changes into Auto Playback.

59
LAUNCH X-431 PRO3S+ V2.0 User Manual

6 Special (Reset) Function

Except that the special functions can be performed from the diagnostic menus
(See Chapter 5.2.3) of certain vehicle model, this module provides an easy dial to
quickly access the special functions.
The most commonly performed service functions contain:
 Oil Reset Service
 Electronic Parking Brake Reset
 Steering Angle Calibration
 ABS Bleeding
 TPMS (Tire Pressure Monitor System) Reset
 Gear Learning
 IMMO Service
 Injector Coding
 Battery Maintenance System
 Diesel Particulate Filter (DPF) Regeneration
 Electronic Throttle Position Reset
 Gearbox Matching
 AFS (Adaptive Front-lighting System) Reset
 Sunroof Initialization
 Suspension Calibration

There are two methods to reset service lamp: Manual reset or Auto reset. Auto
reset follows the principle of sending command from the tool to vehicle’s ECU to
do resetting. While using manual reset, users just follow the on-screen
instructions to select appropriate execution options, enter correct data or values,
and perform necessary actions, the system will guide you through the complete
performance for various service operations.

60
LAUNCH X-431 PRO3S+ V2.0 User Manual

6.1 Oil Reset Service

This function allows you to perform reset for the engine oil life system, which
calculates an optimal oil life change interval depending on the vehicle driving
conditions and climate.
This function can be performed in the following cases:
1. If the service lamp is on, you must provide service for the car. After service,
you need to reset the driving mileage or driving time so that the service lamp
turns off and the system enables the new service cycle.
2. After changing engine oil or electric appliances that monitor oil life, you need
to reset the service lamp.

6.2 Electronic Parking Brake Reset

1. If the brake pad wears the brake pad sense line, the brake pad sense line
sends a signal sense line to the on-board computer to replace the brake pad.
After replacing the brake pad, you must reset the brake pad. Otherwise, the
car alarms.
2. Reset must be performed in the following cases:
a) The brake pad and brake pad wear sensor are replaced.
b) The brake pad indicator lamp is on.
c) The brake pad sensor circuit is short, which is recovered.
d) The servo motor is replaced.

61
LAUNCH X-431 PRO3S+ V2.0 User Manual

6.3 Steering Angle Calibration

To reset the steering angle, first find the relative zero point position for the car to
drive in straight line. Taking this position as reference, the ECU can calculate the
accurate angle for left and right steering.
After replacing the steering angle position sensor, replacing steering mechanical
parts (such as steering gearbox, steering column, end tie rod, steering knuckle),
performing four-wheel alignment, or recovering car body, you must reset the
steering angle.

6.4 ABS Bleeding

This function allows you to perform various bi-directional tests to check the
operating conditions of Anti-lock Braking System (ABS).
1. When the ABS contains air, the ABS bleeding function must be performed to
bleed the brake system to restore ABS brake sensitivity.
2. If the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake
line, or brake fluid is replaced, the ABS bleeding function must be performed
to bleed the ABS.

6.5 Tire Pressure Monitor System Reset

This function allows you to quickly look up the tire sensor IDs from the vehicle’s
ECU, as well as to perform TPMS replacement and sensor test.
1. After the tire pressure MIL turns on and maintenance is performed, the tire
pressure resetting function must be performed to reset tire pressure and turn
off the tire pressure MIL.
2. Tire pressure resetting must be performed after maintenance is performed in
the following cases: tire pressure is too low, tire leaks, tire pressure
monitoring device is replaced or installed, tire is replaced, tire pressure sensor
is damaged, and tire is replaced for the car with tire pressure monitoring
function.

6.6 Gear Learning

The crankshaft position sensor learns crankshaft tooth machining tolerance and
saves to the computer to more accurately diagnose engine misfires. If tooth

62
LAUNCH X-431 PRO3S+ V2.0 User Manual

learning is not performed for a car equipped with Delphi engine, the MIL turns on
after the engine is started. The diagnostic device detects the DTC P1336 'tooth
not learned'. In this case, you must use the diagnostic device to perform tooth
learning for the car. After tooth learning is successful, the MIL turns off.
After the engine ECU, crankshaft position sensor, or crankshaft flywheel is
replaced, or the DTC 'tooth not learned' is present, tooth learning must be
performed.

6.7 IMMO Service

An immobilizer is an anti-theft mechanism that prevents a vehicle’s engine from
starting unless the correct ignition key or other device is present. Most new
vehicles have an immobilizer as standard equipment. An important advantage of
this system is that it doesn’t require the car owner to activate it since it operates
automatically. An immobilizer is considered as providing much more effective
anti-theft protection than an audible alarm alone.
As an anti-theft device, an immobilizer disables one of the systems needed to
start a car’s engine, usually the ignition or the fuel supply. This is accomplished
by radio frequency identification between a transponder in the ignition key and a
device called a radio frequency reader in the steering column. When the key is
placed in the ignition, the transponder sends a signal with a unique identification
code to the reader, which relays it to a receiver in the vehicle’s computer control
module. If the code is correct, the computer allows the fuel supply and ignition
systems to operate and start the car. If the code is incorrect or absent, the
computer disables the system, and the car will be unable to start until the correct
key is placed in the ignition.
To prevent the car being used by unauthorized keys, the anti-theft key matching
function must be performed so that the immobilizer control system on the car
identifies and authorizes remote control keys to normally use the car.
When the ignition switch key, ignition switch, combined instrument panel, ECU,
BCM, or remote control battery is replaced, anti-theft key matching must be
performed.

6.8 Injector Coding

Write injector actual code or rewrite code in the ECU to the injector code of the
corresponding cylinder so as to more accurately control or correct cylinder

63
LAUNCH X-431 PRO3S+ V2.0 User Manual

injection quantity.
After the ECU or injector is replaced, injector code of each cylinder must be
confirmed or re-coded so that the cylinder can better identify injectors to
accurately control fuel injection.

6.9 Battery Maintenance System Reset

This function enables you to perform a resetting operation on the monitoring unit
of vehicle battery, in which the original low battery fault information will be
cleared and battery matching will be done.
Battery matching must be performed in the following cases:
a) Main battery is replaced. Battery matching must be performed to clear
original low battery information and prevent the related control module from
detecting false information. If the related control module detects false
information, it will invalidate some electric auxiliary functions, such as
automatic start & stop function, sunroof without one-key trigger function,
power window without automatic function.
b) Battery monitoring sensor. Battery matching is performed to re-match the
control module and motoring sensor to detect battery power usage more
accurately, which can avoid an error message displaying on the instrument
panel.

6.10 Diesel Particulate Filter (DPF) Regeneration

DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter
through continuous combustion oxidation mode (such as high temperature
heating combustion, fuel additive or catalyst reduce PM ignition combustion) to
stabilize the filter performance.
DPF regeneration may be performed in the following cases:
a) The exhaust back pressure sensor is replaced.
b) The PM trap is removed or replaced.
c) The fuel additive nozzle is removed or replaced.
d) The catalytic oxidizer is removed or replaced.
e) The DPF regeneration MIL is on and maintenance is performed.
f) The DPF regeneration control module is replaced.

64
LAUNCH X-431 PRO3S+ V2.0 User Manual

6.11 Electronic Throttle Position Reset

This function enables you to make initial settings to throttle actuators and returns
the “learned” values stored on ECU to the default state. Doing so can accurately
control the actions of regulating throttle (or idle engine) to adjust the amount of
air intake.

6.12 Gearbox Matching

1. This function can complete the gearbox self-learning to improve gear shifting
quality.
2. When the gearbox is disassembled or repaired (after some of the car battery
is powered off), it will lead to shift delay or impact problem. In this case, this
function needs to be done so that the gearbox can automatically compensate
according to the driving conditions so as to achieve more comfortable and
better shift quality.

6.13 AFS (Adaptive Front-lighting System) Reset

This feature is used to initialize the adaptive headlamp system. According to the
ambient light intensity, the adaptive headlamp system may decide whether to
automatically turn on the headlamps, and timely adjust the headlamp lighting
angle while monitoring the vehicle speed and body posture.

6.14 Sunroof Initialization

This function can set the sunroof lock off, closed when it rains, sliding / tilting
sunroof memory function, temperature threshold outside the car etc.

6.15 Suspension Calibration

1. This function can adjust the height of the body.
2. When replacing the body height sensor in the air suspension system, or
control module or when the vehicle level is incorrect, you need to perform this
function to adjust the body height sensor for level calibration.

65
LAUNCH X-431 PRO3S+ V2.0 User Manual

7 Software Update

This module allows you to update the diagnostic App and frequently used
software.

7.1 Update Diagnostic Software & APP

Go to Software Update on the Diagnostics function selection screen and tap the
Downloaded tab.
The Available tab displays a list of software that can be updated. Under it, all
software is categorized into three kinds:
• Common software: mainly includes some common apps that are associated
with the diagnostic app. The software of this kind always stays at the top of
the list, which can be deselected manually (excluding the system app, such
as firmware and ECU aid).
• Frequently used vehicle software: refers to the diagnostic software that is
frequently used, including the vehicle diagnostic software and Reset
software. It is generally displayed following the Common software list.
• Other vehicle software: refers to the diagnostic software that is rarely used
or never used. It is generally displayed following the Frequently used
software list.
1). If the user does not download any diagnostic software during the sign-up
process, all diagnostic software is selected by default. Tap Update to start
downloading.
2). If the user downloaded all/some vehicle software during the sign-up process
and had it serviced for a long period of time, only the frequently used
software is selected. Tap Update to start downloading. Other vehicle
software that is rarely used will also be listed under the Available tab, but it is
not selected at default.

66
LAUNCH X-431 PRO3S+ V2.0 User Manual

Once download is finished, the software packages will be installed automatically.

To download certain software that is not frequently used, check the box before
the vehicle model. Tap Update to start downloading.
Once download is finished, the software packages will be installed automatically.

7.2 Update Frequently Used Software

If the user only intends to update the frequently used software, go to Software
Update and tap the Downloaded tab.

Tap Update to start downloading. Once download is finished, the software

packages will be installed automatically.

67
LAUNCH X-431 PRO3S+ V2.0 User Manual

7.3 Renew Software Subscription

If the software subscription is due or expires, the system will prompt you to
renew your subscription.
Tap Renewal on the bottom of the screen to enter the payment screen.
There are three ways available for you to make payment: PayPal, Subscription
Renewal Card (*need to buy it from the local dealer where you purchased the tool)
and Credit Card.

1. Using PayPal
1. Select PayPal, and then follow the on-screen instructions to finish the
transaction.
2. After payment, go to update center to update the diagnostic software.
2. Using Subscription Renewal Card
1. Select Subscription Renewal Card.

68
LAUNCH X-431 PRO3S+ V2.0 User Manual

2. Input the 24-digit pin code of Subscription Renewal Card and then tap Submit
to finish the renewal.
3. Go to update center to update the diagnostic software.

3. Using Credit Card

1. Select Credit Card, and then follow the on-screen instructions to finish the
transaction.
2. After payment, go to update center to update the diagnostic software.

69
LAUNCH X-431 PRO3S+ V2.0 User Manual

8 User Info

This function allows users to manage personal information and VCI.

8.1 VCI
This option allows you to manage all your activated VCI devices.
If several VCI devices are activated on this tool, a list of VCIs will be displayed
on the screen. Once you choose the VCI that belongs to other account, you
have to log out, and then input the right account to continue.

8.2 VCI Management (Only for Passenger Vehicle

Configuration)
This option is used for the tablet to deactivate pairing up with the VCI device via
Bluetooth.

8.2 VCI Management (Only for Diesel & Gasoline Configuration)

This option is used to set the communication method between the tablet and the
VCI module.

To ensure the tablet can work with the VCI module via Wi-Fi communication,
please follow the steps below to proceed:
1. Check the box Use Wi-Fi communication mode, the system will search for
VCI module automatically.

70
LAUNCH X-431 PRO3S+ V2.0 User Manual

2. Tap the desired VCI module and a pairing request similar to the following
prompt window will appear:

3. Tap PAIR to start pairing. Once the pairing is successfully done, the following
screen will appear:

71
LAUNCH X-431 PRO3S+ V2.0 User Manual

4. There are two Wi-Fi communication modes available for the VCI module.
 Work as Wi-Fi hotspot: Once enabled, the VCI module and the tablet
automatically connect and form a LAN network to make communication. In
this case, the tablet cannot surf the Internet.
 Work as network adaptor: Once enabled, a Wi-Fi connection dialog box
appears:

Input the Wi-Fi network name and access password (if the network is
encrypted) until it is properly connected. In this case, the tablet can surf the
Internet and communicate with the VCI module.
Note: please be sure to keep the VCI powered on while performing the operation.

8.3 Activate VCI

This item lets you to activate a new VCI device.

72
LAUNCH X-431 PRO3S+ V2.0 User Manual

Input the Serial Number and Activation Code, and then tap Activate to activate
the VCI.
For details on how to obtain Activation Code, tap the link below to get help.

8.4 Firmware Fix

Use this item to upgrade and fix diagnostic firmware. During fixing, please do not
cut power or switch to other interfaces.

8.5 Data Stream Sample

This feature allows you to manage the recorded data stream sample files.

8.6 My Order
This item allows you to check the status of all your orders.

8.7 Subscription Renewal Card

This item is used to check the status of the subscription renewal card.

73
LAUNCH X-431 PRO3S+ V2.0 User Manual

Input the 12-digit subscription renewal card number. Tap Search to get the
search result.

8.8 Profile
Use this item to view and configure personal information.

• Tap the user image to change it.

• Tap > next to Free Upgrade Period to check the due date of all diagnostic
software.

8.9 Change password

This item allows you to modify your login password.

8.10 Settings
It enables you to make some application settings and view software version
information etc.

8.10.1 Units
It is designed to configure the measurement unit. Metric System and English
System are available.

74
LAUNCH X-431 PRO3S+ V2.0 User Manual

8.10.2 Shop Information

This option lets you define your print information. It mainly includes Workshop,
Address, Telephone, Fax and License Plate.

After inputting, tap Save.

Once you saved the print information, it will be entered automatically in the Add
Information box every time you save the diagnostic report.

8.10.3 Printer Set

This option is designed to establish a wireless connection between the tablet
and the Wi-Fi printer (sold separately) while performing printing operations.
The App is compatible with the LAUNCH Wi-Fi Printer (sold separately) and
System (external printer).

For LAUNCH Wi-Fi printer, follow the steps below to connect the printer.
1. Tap Printer Set.

75
LAUNCH X-431 PRO3S+ V2.0 User Manual

A. If it is the first time you have operated this printer, please proceed the
following:
1. For initial use, you are suggested to reset the printer: Press and hold MODE
& FEED for 8 seconds, the following resetting command will be printed out:
at + default = 1
ok
at + reboot = 1
rebooting...
2. Tap Reset to configure Wi-Fi printer.
Step 1: Connect the printer:
Tap Scan to start scanning and select the desired printer hotspot named with
X-431PRINTER-XXXX (XXXX stands for 4 characters), and then tap
Connect to enter Step 2.
Step 2: Join the Wi-Fi printer into LAN:
Tap Scan to select the desired local Wi-Fi network from the list, and type in
the security password (If it is an open network, password is not required), and
then tap Confirm.
3. Once the Wi-Fi network of the printer is connected and the printer is found,
tap Printing test to test the printing.
Now the Wi-Fi printer is ready for printing.

76
LAUNCH X-431 PRO3S+ V2.0 User Manual

If the printer is not found, please reset the printer to default factory settings (refer
to Step 2 for details) and check whether the current device and the printer are on
the same LAN.
B. If you have configured the Wi-Fi printer to the LAN:
2. Tap Connect to Printer:
a). If the local network remains as it is, tap Test Print directly to test the
printing.
b). If the local network changes, you have to reset the Wi-Fi printer.

For other Wi-Fi printers,

Before printing, make sure the following conditions are met:
• The Wi-Fi printer is powered on and working normally.
• The print service plug-in associated with the printer is already installed on the
tablet (Go to Google Play or use the Browser to download and install it).
Follow the steps below to proceed:
1. Set the default printer as System.
2. Go to Other Modules -> Tablet Settings -> WLAN, set the WLAN switch to
Off.

3. On the report details page, tap .

4. Touch next to Select a printer on the upper left corner of the screen.

77
LAUNCH X-431 PRO3S+ V2.0 User Manual

5. Select All Printers -> Add printer and enable the installed printer service,
the system starts searching for all available Wi-Fi printers of the brand.

6. Select the desired Wi-Fi printer from the list. If the chosen Wi-Fi printer
hotspot is open, the tablet can connect it directly. If it is encrypted, a
password may be required. Refer to the Wi-Fi printer user manual to get the
default password.
7. Now the printer is ready for printing.
8. Alternatively, you can also choose Save as PDF to save the current
diagnostic report as a PDF file for later printing.

8.10.4 Orientation
The option is used to set the screen display orientation.

78
LAUNCH X-431 PRO3S+ V2.0 User Manual

8.10.5 Clear Cache

This option allows you to clear the App cache. Clearing the cache will restart the
App.

8.10.6 About
The software version information and disclaimer are included.

8.10.7 Diagnostic Software Auto Update

This option is used to set whether automatic update function is ON.

8.10.8 Device Account Management

This option allows you to create and manage sub accounts. Users can use the
Created account to log in this tool and the bound VCI device to perform vehicle
diagnosis.
Tap Device Account Management, the following screen will appear:

Tap Add sub account, the following screen will appear:

79
LAUNCH X-431 PRO3S+ V2.0 User Manual

There are two types of sub accounts: one is the golo auto repair technician
account authorized by the master account, the other is the created account.
 If you have registered a golo account, tick Use golo auto repair technician
user, input the username and password and tap Add immediately to bind it
to the current account.
 If you have not registered an account, tick Create sub user, the following
screen will appear:

Input the username and password and tap Add immediately to bind it to the
current account.
After successfully adding the sub account, the following screen will appear:

80
LAUNCH X-431 PRO3S+ V2.0 User Manual

To unbind the sub account from the current account, tap Remove.

8.10.9 Login/Logout
To logout the current user ID, tap Logout.
To login the system again, tap Login.

8.11 Diagnostic Software Clear

This item allows you to hide/clear the diagnostic software that is not frequently
used.
Note: Removing software may completely delete the software from the tablet. If
some software is not used and the tablet runs out of space, you can use this feature to
remove it. To re-download it, go to Software Update.

81
LAUNCH X-431 PRO3S+ V2.0 User Manual

9 TPMS

This module allows you to configure the tablet as TPMS activation & diagnostic
tool, which provides the ability to trigger TPMS sensor, program TPMS sensor,
perform the relearning procedure. It needs to work with the X-431 TSGUN
device (sold separately).
Below illustrates how the tablet works with the X-431 TSGUN.

For more details, refer to the User Manual included with the X-431 TSGUN.

82
LAUNCH X-431 PRO3S+ V2.0 User Manual

10 FAQ

1. How to save power?

• Please turn off the screen while the tool keeps idle.
• Set a shorter standby time.
• Decrease the brightness of the screen.
• If WLAN connection is not required, please turn it off.
• Disable GPS function if GPS service is not in use.

2. Communication error with vehicle ECU?

Please confirm:
1. Whether diagnostic connector is correctly connected.
2. Whether ignition switch is ON.
3. If all checks are normal, send vehicle year, make, model and VIN number to
us using Feedback feature.

3. Failed to enter into vehicle ECU system?

Please confirm:
1. Whether the vehicle is equipped with this system.
2. Whether the VCI dongle is correctly connected.
3. Whether ignition switch is ON.
4. If all checks are normal, send vehicle year, make, model and VIN number to
us using Feedback feature.

4. How to download the X-431 PRO3S+ V2.0 App after resetting the tablet?

*Note: Before registration, please make sure the network is properly connected.
After the tablet has been successfully reset, follow the steps below to download
the App:
1. Launch the browser and the default official Launch website opens (If a blank
page pops up, just type in www.x431.com in the input bar).
2. Tap Login, input the username and password and tap Log In.
3. Make sure that the serial number is correct, tap APP application program
and tap the Download icon to start downloading.

83
LAUNCH X-431 PRO3S+ V2.0 User Manual

4. After the download is complete, follow the on-screen instructions to install it.
5. After installation, use the existing username and password to login and go to
update center to download the diagnostic software.

5. What to do if the language of vehicle diagnostic software does not

match the system language?

English is the default system language of the tool. After the system language is
set to the preference language, please go to the update center to download the
vehicle diagnostic software of the corresponding language.
If the downloaded diagnostic software is still displayed in English, it indicates
that the software of the current language is under development.

6. How to retrieve the login password?

Please follow below steps to proceed in case you forgot the login password:
1. Tap the application icon on the home screen to launch it.
2. Tap Login on the upper right corner of the screen.
3. Tap Retrieve password.
4. Input product S/N and follow the on-screen prompts to retrieve the password.

84
Warranty
THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE
LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE
ORDINARY COURSE OF THE BUYER’S BUSINESS.
LAUNCH electronic product is warranted against defects in materials and
workmanship for one year from date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a
purpose other than for which it was intended, or used in a manner inconsistent
with instructions regarding use. The exclusive remedy for any automotive meter
found to be defective is repair or replacement, and LAUNCH shall not be liable
for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with
procedures established by LAUNCH. No agent, employee, or representative of
LAUNCH has any authority to bind LAUNCH to any affirmation, representation,
or warranty concerning LAUNCH automotive meters, except as stated herein.

Disclaimer
The above warranty is in lieu of any other warranty, expressed or implied,
including any warranty of merchantability or fitness for a particular purpose.

Purchase Order
Replaceable and optional parts can be ordered directly from your LAUNCH
authorized tool supplier. Your order should include the following information:
 Order quantity
 Part number
 Part name

Customer Service
Any question during the operation, please call +86-755-84557891 or send Email
to our official after-sale service email address: [email protected].
If your unit requires repair service, return it to the manufacturer with a copy of
the sales receipt and a note describing the problem. If the unit is determined to
be in warranty, it will be repaired or replaced at no charge. If the unit is
determined to be out of warranty, it will be repaired for a nominal service charge
plus return freight. Send the unit pre-paid to:

Attn: Customer Service Department

LAUNCH TECH CO., LTD.
Launch Industrial Park,
North of Wuhe Avenue,
Banxuegang, Bantian,
Longgang, Shenzhen, Guangdong
P.R.China, 518129
Launch website: http://www. cnlaunch.com
http://www.x431.com

Statement:
LAUNCH reserves the rights to make any change to product designs and
specifications without notice. The actual object may differ a little from the
descriptions in the manual in physical appearance, color and configuration. We
have tried our best to make the descriptions and illustrations in the manual as
accurate as possible, and defects are inevitable, if you have any question,
please contact local dealer or after-sale service center of LAUNCH, LAUNCH
does not bear any responsibility arising from misunderstandings.