The document discusses technical drawing and includes questions about different types of technical drawings like orthographic, isometric, and perspective drawings. It also includes questions about different geometric shapes and curves like conic sections, spirals, loci, and their properties. Construction of views from pictorial drawings and specific geometric shapes like involutes and ellipses are also included as part of the document.
The document discusses technical drawing and includes questions about different types of technical drawings like orthographic, isometric, and perspective drawings. It also includes questions about different geometric shapes and curves like conic sections, spirals, loci, and their properties. Construction of views from pictorial drawings and specific geometric shapes like involutes and ellipses are also included as part of the document.
The document discusses technical drawing and includes questions about different types of technical drawings like orthographic, isometric, and perspective drawings. It also includes questions about different geometric shapes and curves like conic sections, spirals, loci, and their properties. Construction of views from pictorial drawings and specific geometric shapes like involutes and ellipses are also included as part of the document.
The document discusses technical drawing and includes questions about different types of technical drawings like orthographic, isometric, and perspective drawings. It also includes questions about different geometric shapes and curves like conic sections, spirals, loci, and their properties. Construction of views from pictorial drawings and specific geometric shapes like involutes and ellipses are also included as part of the document.
Download as DOCX, PDF, TXT or read online from Scribd
Download as docx, pdf, or txt
You are on page 1/ 4
SS 2 TECHNICAL DRAWING
PAPER 1 (OBJECTIVE) Section A
C. Involute D. Parabola 7. Which of the following is a conic section? A. Apex B. Circle C. Rectangle D. Square 1. What method of projection is the block 8. A spiral shaped curve around a cylinder or drawn above? cone is called a/an A. Oblique . A. cycloid B. Isometric . B. helix C. Auxiliary. C. link mechanism D. Orthographic . D. involute 2. The angle between the isometric axes is 9. The curve which has eccentricity zero is __________ _______ A. 180 degrees A. Parabola B. 60 degrees B. Ellipse C. 90 degrees C. Hyperbola D. 120 degrees D. Circle 3. The length in isometric drawing of line is 20 10. Locus of the point P such that the sum of cm. What is the true length of it? distances from two fixed points is always [Taken the value of the ratio of isometric constant is __________ length to true length = 0.815]. A. a ellipse A. 24.53 cm B. a hyperbola B. 15.46 cm C. a parabola C. 19.31 cm D. an involute D. 23.09 cm 11. In a first angle projection, where does the 4. Which of the following are equal in area vertical plane lies? to triangle ABC in the drawing below? A. above the horizontal plane B. beside the horizontal plane C. below the horizontal plane D. above the side vertical plane 12. What does letter D represent in the triangle below?
A. ABCD B. AFG C. BCFG D. CEF 5. The planes parallel to any of the two A. Apex isometric lines are called ________ planes. A. parallel B. Base B. auxiliary C. Median C. isometric D. Vertex D. oblique 13. Which of this is not correct about Orthographic projection 6. Which of the following is drawn using the A. they produce 3D pictorial Drawing tangents to a given circle? A. Ellipse B. they show the view of the observer line of sight B. Hyperbola C. They are parallel projection techniques D. they are 2D drawing 14. Which of the following is not a pictorial drawing? A. isometric B. multiview C. perspective D. axonometric A. AGDC B. BDEF 15. The angles of orthographic projections are C. EGBF ____ D. HGDB A. 1st and 3rd B. 1st and 2nd 18. An advantage of this type of view is that C. 2nd and 3rd each view shows the object all the way D. 3rd and 4th through as if it were transparent: A. Planar 16. What type of loci is the diagram below B. Horizontal C. Auxiliary D. Orthographic 19. What is the name given to the locus of a A. Archimedean spiral point on the end of a string as it is unwound B. epicycloid from a circle? C. hypocycloid A. cycloid D. ellipse B. ellipse C. Helix 17. Which of the following are equal in area D. involute to triangle ABC in the drawing below? 20. The top, front, and bottom views align in this manner: A. Horizontally B. Vertically C. According to the planar views D. Parallel to the frontal plane
Section B (Part I) Answer all questions
With the aid of annotated diagram, explain the following types of drawing
CONSTRUCTION Answer only one in this section 1a. The pictorial view of a sliding block is shown below. Draw in the first angle projection, the full size of the following views, with hidden details: I．front elevation in the direction of arrow K; II．plan; III．end elevation in the direction of arrow P. b. From the isometric block shown below, construct only the front elevation in the direction of arrow K in scale 2:1.
2a. Construct Construct the involute of a rectangle with dimensions of 30 by 60.
b. Construct an ellipse with greater axis 120mm and smaller axis 80mm
Note: Use full scale for all your construction works unless instructed otherwise and dimensions should be in millimeters. A well established border line and title block make up 20% mark in this section. All construction lines must be shown clearly. Accuracy and good draughtsmanship are essential.
