X LD3508B Tuner to IP Gateway

User’s Manual
 DIRECTORY

CHAPTER 1 PRODUCT OUTLINE ................................................................................................ 1

1.1 Outline ................................................................................................................................................... 1

1.2 Features .................................................................................................................................................. 1

1.3 Inner Principle........................................................................................................................................ 2

1.4 Specifications........................................................................................................................................... 2

1.5 Appearance and Description ................................................................................................................... 2

CHAPTER 2 INSTALLATION GUIDE........................................................................................... 4

2.1 Acquisition Check ................................................................................................................................... 4

2.2 Installation Preparation .......................................................................................................................... 4

2.3 Wire’s Connection................................................................................................................................... 6

CHAPTER 3 WEB NMS OPERATION ........................................................................................... 7

3.1 login ....................................................................................................................................................... 7

3.2 Operation ............................................................................................................................................... 7

CHAPTER 4 TROUBLESHOOTING............................................................................................18

CHAPTER 5 PACKING LIST .........................................................................................................19

 Chapter 1 Product Outline

1.1 Outline

XLD3508B Tuner to IP Gateway is a head -end interface conversion device which

supports MPTS and SPTS output switchable. It supports 16 MPTS or 512 SPTS output
over UDP and RTP/RTSP protocol. It is integrated with tuner demodulation (or ASI input)
and gateway function, which can demodulate the signal from 16 tuners into IP pa ckage,
or directly convert the TS from ASI input and tuner into IP package, then output the IP
package through different IP address and ports. BISS function is also embedded for tuner
input to descramble your tuner input programs.

1.2 Features

 Support 16 FTA DVB- S/S2 (DVB-C/T/T2 /ISDB-T/ATSC optional )input, 2 ASI input
 Support BISS descrambling
 Support DisEqc function
 16 MPTS or 512 SPTS output (MPTS and SPTS output switchable)
 2 GE mirrored output (IP address and port number of GE1 and GE2 are different), up to
850Mbps---SPTS
 2 independent GE output port, GE1 + GE2---MPTS
 Support PID filtering, re-mapping (Only for SPTS output)
 Support “Null PKT Filter” function (Only for MPTS output)

 Support Web operation

1
1.3 Inner Principle

Tuner 1
X LD3508B
Tuner 2
Tuner 3

GE1
IP Output

IP Output
Tuner 15 GE2

Tuner 16

ASI Input1

ASI Input2

1.4 Specifications

Optional 1:16 tuners input +2 ASI input---SPTS output

Input Optional 2:14 tuners input +2 ASI input --- MPTS output
Optional 3:16 tuners input --- MPTS output
Standard J.83A(DVB-C), J.83B, J.83C
DVB-C Frequency In 30 MHz~1000 MHz
Constellation 16/32/64/128/256 QAM
Frequency In 30MHz ~999.999 MHz
DVB-T/T2
Bandwidth 6/7/8 M bandwidth
Input Frequency 950-2150MHz
Tuner Section DVB-S: QPSK 2~45Mbauds;
Symbol rate DVB-S2:QPSK1~45Mbauds, 8PSK
DVB-S/S2
2~30Mbauds
Code rate 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10
Constellation QPSK, 8PSK
ISDB-T Input Frequency 30-1000MHz
Input Frequency 54MHz~858MHz
ATSC
Bandwidth 6M bandwidth
512 SPTS IP mirrored output over UDP and RTP/RTSP protocol through
GE1 and GE2 port, Unicast and Multicast
Output 16 MPTS IP output (for Tuner/ASI passthrough) over UDP and RTP/RTSP
protocol through GE1 and GE2 port (IP address and port number of GE1
and GE2 are different), Unicast and Multicast
BISS Descrambling Mode 1, Mode E (Up to 850Mbps) (descramble individual program)
Dimension 482mm×410mm×44mm (W×L×H)
Approx weight 3.6kg
Miscellaneous Environment 0~45℃(work)；-20~80℃（Storage）
Power requirements 100~240VAC, 50/60Hz
Power consumption 20W

2
1.5 Appearance and Description

Front Panel Illustration:

1 Power indicator
2 Reset: Reset webmaster IP address, recover it to default IP address

3 USB port for upgrade

4 NMS port: Network management interface

5 Data port（GE1&GE2）: IP out port

6 ASI input port

Rear Panel Illustration

1 16 channels RF IN Interface
2 Integrated power switch and socket

3 Grounding Wire

3
 Chapter 2 Installation Guide

2.1 Acquisition Check

When users open the package of the device, it is necessary to check items according to
packing list. Normally it should include the following items:
 XLD3508B Tuner to IP Gateway
 User‟s Manual
 Grounding Cable
 RF In and Loop Out Cable
 Power Cord
If any item is missing or mismatching with the list above, please contact local dealer.

2.2 Installation Preparation

When users install device, please follow the below steps. The details of installation will be
described at the rest part of this chapter. Users can also refer rear panel chart during the
installation.
The main content of this chapter including:
 Checking the possible device missing or damage during the transportation
 Preparing relevant environment for installation
 Installing gateway
 Connecting signal cables
 Connecting communication port (if it is necessary)

2.2.1 Device’s Installation Flow Chart Illustrated as following：

Connecting
Grouding
Acquisition Fixing Connecting Setting Running
Wire and
Check Device Signal Wire Parameter Device
Power
Cord

2.2.2 Environment Requirement

4
 Item Requirement

When user installs machine frame array in one machine hall, the
Machine Hall Space distance between 2 rows of machine frames should be 1.2~1.5m
and the distance against wall should be no less than 0.8m.

Electric Isolation, Dust Free

Volume resistivity of ground anti-static material:
Machine Hall Floor
1X107~1X1010 ，Grounding current limiting resistance: 1M
(Floor bearing should be greater than 450Kg/㎡)

Environment 5~40℃(sustainable )，0~45℃(short time)，

Temperature installing air-conditioning is recommended

Relative
20%~80% sustainable 10%~90% short time
Temperature

Pressure 86~105KPa

Installing rubber strip for sealing door-gaps and dual level

Door & Window
glasses for window

Wall It can be covered with wallpaper, or brightness less paint.

Fire Protection Fire alarm system and extinguisher

Requiring device power, air-conditioning power and lighting

power are independent to each other. Device power requires AC
Power
power 100V-240V 50/60Hz 2A. Please carefully check before
running.

2.2.3 Grounding Requirement

 All function modules‟ good grounding designs are the basis of reliability and stability of
devices. Also, they are the most important guarantee of lightning arresting and
interference rejection. Therefore, the system must follow this rule.
 Coaxial cable‟s outer conductor and isolation layer should keep proper electric
conducting with the metal housing of device.
 Grounding conductor must adopt copper conductor in order to reduce high frequency
impedance, and the grounding wire must be as thick and short as possible.
 Users should make sure the 2 ends of grounding wire well electric conducted and be
5
 antirust.
 It is prohibited to use any other device as part of grounding electric circuit
 The area of the conduction between grounding wire and device‟s frame should be no less
than 25mm2.

2.2.4 Frame Grounding

All the machine frames should be connected with protective copper strip. The grounding wire
should be as short as possible and avoid circling. The area of the conduction between
grounding wire and grounding strip should be no less than 25mm2.

2.2.5 Device Grounding

Connecting the device‟s grounding rod to frame‟s grounding pole with copper wire.

2.3 Wire’s Connection

The grounding wire conductive screw is located at the right end of rear panel, and the power
switch, fuse, power supply socket is just beside ,whose order goes like this, power switch is
on the left ,power supply socket is on the right and the fuse is just between them.
 Connecting Power Cord
User can insert one end into power supply socket, while insert the other end to AC power.
 Connecting Grounding Wire
When the device solely connects to protective ground, it should adopt independent way,
say, share the same ground with other devices. When the device adopts united way, the
grounding resistance should be smaller than 1Ω.

Caution:

Before connecting power cord to NDS3508B Tuner to IP Gateway, user should set the
power switch to “OFF”.

6
 Chapter 3 WEB NMS operation
User can only control and set the configuration in computer by connecting the device to web
NMS Port. User should ensure that the computer‟s IP address is different from the
XLD3508B‟s IP address; otherwise, it would cause IP conflict.

3.1 login

The default IP of this device is 192.168.0.136.

Connect the PI and the device with net cable, and use ping command to confirm they are on
the same network segment.
I.G. the PC IP address is 192.168.99.252, we then change the device IP to 192.168.99.xxx (xxx
can be 0 to 255 except 252 to avoid IP conflict).
Use web browser to connect the device with PC by inputting this device‟s IP address in the
browser‟s address bar and press Enter.
It displays the Login interface as Figure-1. Input the Username and Password (Both the
default Username and Password are “admin”.) and then click “Login” to start the device
setting.

Figure-1

3.2 Operation

Summary → Status
When we confirm the login, it displays the status interface as Figure-2.

7
 System information

User can click any item here to enter

the corresponding interface to check
information or set the parameters.

Figure-2

Parameter→ Tuner input (DVB-S/S2)

From the menu on top side of the webpage, click “Tuner Input”, it displays the interface
where users can check the 16 channels Tuner input status. (Figure-3)

16 Tuner input
status

8
 Figure-3

Parameter→ Tuner input (DVB-T/T2)

From the menu on top side of the webpage, click “Tuner Input”, it displays the interface
where users can check the 16 channels Tuner input status. (Figure-4)

Figure-3

16 Tuner input
status

Figure-4

Parameter→ ASI input

From the menu on top side of the webpage, click “ASI Input”, it displays the interface where
users can check the 2 channels ASI input status. (Figure-5)

9
 Figure-5

Parameter→ BISS
From the menu on left side of the webpage, clicking “BISS”, it displays the interface where
users can configure BISS and descramble the input channels (Figure-6).

Select the output carrier

Figure-6

Parameter→ Program Parse

From the menu on left side of the webpage, clicking “Program Parse”, it displays the interface
where users can parse the program from the input channels.

10
When users disable the ASI input, XLD3508B can support 16 Tuner input with 16 MPTS IP
output (Figure-7).

Enable and Disable the

ASI input

Figure-7
When users enable the ASI input, XLD3508B can support 1 4 Tuner input and 2 ASI input
with 16 MPTS IP output (Figure-8).

Figure-8

Parameter→ IP Stream
XLD3508B supports TS to output in IP (16*MPTS) format through the GE1 or GE2 port.
Clicking “IP Stream”, it displays the interface where to set IP out parameters (Figure-9).

11
 Figure-9
NDS3508B support 16 Tuner input and 2 ASI input with 512 SPTS output, the parameter
interface is different from MPTS. When users switch MPTS to SPTS, new mode will work
after reboot the device.

Parameter→ TS Config
Clicking “TS Config”, it displays the interface where users can set the output TS and
configure TS ID and ON ID (Figure-10).

Figure-10

Parameter→ BISS:
From the menu on left side of the webpage, clicking “BISS”, it displays the interface where
users can configure BISS and descramble the input channels (Figure-11).

12
 Figure-11

Parameter → SPTS Select:

From the menu on left side of the webpage, clicking “SPTS Select”, it displays the interface
where users can choose 16 Tuner input and 2 ASI Input programs to output from IP (max 512
SPTS). (Figure-12)

Input Area Output Area

Operation Area

Figure-12
Configure „Input Area‟ and „Output Area‟ with buttons in „Operation Area‟. Instructions are as
below:

: To filter/not filter the source CA information

13
 : To enable/disable the PID remapping

To refresh the input program information

To refresh the output program information

Select one input program first and click this button to transfer the selected
program to the right box to output.
Similarly, user can cancel the multiplexed programs from the right box.
To select all the input programs
To select all the output programs

To parse programs time limitation of parsing input programs

 Program Modification:
The multiplexed program information can be modified by clicking the program in the „output‟
area. For example, when clicking , it triggers a dialog box (Figure 13) where
users can input new information.

Figure-13

System → Network:
Clicking “Network”, it displays the interface as Figure-14 where to set network parameters.

14
 Figure-14

System → Password:
From the menu on left side of the webpage, clicking “Password”, it displays the screen as
Figure-15 where to set the login account and password for the web NMS.

Figure-15

System → Save/Restore:
From the menu on left side of the webpage, clicking “Save/Restore”, it displays the screen
as Figure-16 where to save or restore your configurations.

15
 Figure-16

System → Backup/Load:
From the menu on left side of the webpage, clicking “Backup/Load”, it displays the screen
as Figure-17 where to backup or load your configurations.

Figure-17

System → Firmware:
From the menu on left side of the webpage, clicking “Firmware”, it displays the screen as
Figure-18 where to update firmware for the device.

16
 Select IP output
Mode, click “Apply”
and reboot the device
then the new mode
can start to work.

Figure-18

17
 Chapter 4 Troubleshooting

XIELID s ISO9001 quality assurance system has been approved by CQC organization. For
guarantee the products‟ quality, reliability and stability. All our products have been passed
the testing and inspection before ship out factory. The testing and inspection scheme already
covers all the Optical, Electronic and Mechanical criteria which have been published by
us. To prevent potential hazard, please strictly follow the operation conditions.

Prevention Measure

 Installing the device at the place in which environment temperature between 0 to 45 °C

 Making sure good ventilation for the heat-sink on the rear panel and other heat-sink bores
if necessary
 Checking the input AC within the power supply working range and the connection is
correct before switching on device
 Checking the RF output level varies within tolerant range if it is necessary
 Checking all signal cables have been properly connected
 Frequently switching on/off device is prohibited; the interval between every switching
on/off must greater than 10 seconds.

Conditions need to unplug power cord

 Power cord or socket damaged.

 Any liquid flowed into device.
 Any stuff causes circuit short
 Device in damp environment
 Device was suffered from physical damage
 Longtime idle.
 After switching on and restoring to factory setting, device still cannot work properly.
 Maintenance needed

18
 Chapter 5 Packing list
 XLD3508B Tuner to IP gateway
 User‟s manual
 Grounding cable
 RF In and Loop Out Cable
 Power cord

19