SS 2 TECHNICAL DRAWING

PAPER 1
(OBJECTIVE) Section A

C. Involute
D. Parabola
7. Which of the following is a conic section?
A. Apex
B. Circle
C. Rectangle
D. Square
1. What method of projection is the block 8. A spiral shaped curve around a cylinder or
drawn above? cone is called a/an
A. Oblique . A. cycloid
B. Isometric . B. helix
C. Auxiliary. C. link mechanism
D. Orthographic . D. involute
2. The angle between the isometric axes is 9. The curve which has eccentricity zero is
__________ _______
A. 180 degrees A. Parabola
B. 60 degrees B. Ellipse
C. 90 degrees C. Hyperbola
D. 120 degrees D. Circle
3. The length in isometric drawing of line is 20 10. Locus of the point P such that the sum of
cm. What is the true length of it? distances from two fixed points is always
[Taken the value of the ratio of isometric constant is __________
length to true length = 0.815]. A. a ellipse
A. 24.53 cm B. a hyperbola
B. 15.46 cm C. a parabola
C. 19.31 cm D. an involute
D. 23.09 cm
11. In a first angle projection, where does the
4. Which of the following are equal in area vertical plane lies?
to triangle ABC in the drawing below? A. above the horizontal plane
B. beside the horizontal plane
C. below the horizontal plane
D. above the side vertical plane
12. What does letter D represent in the
triangle below?

A. ABCD
B. AFG
C. BCFG
D. CEF
5. The planes parallel to any of the two A. Apex
isometric lines are called ________ planes.
A. parallel B. Base
B. auxiliary C. Median
C. isometric D. Vertex
D. oblique 13. Which of this is not correct about
Orthographic projection
6. Which of the following is drawn using the A. they produce 3D pictorial Drawing
tangents to a given circle?
A. Ellipse B. they show the view of the observer line of
sight
B. Hyperbola
C. They are parallel projection techniques
D. they are 2D drawing
14. Which of the following is not a pictorial
drawing?
A. isometric
B. multiview
C. perspective
D. axonometric A. AGDC
B. BDEF
15. The angles of orthographic projections are C. EGBF
____ D. HGDB
A. 1st and 3rd
B. 1st and 2nd 18. An advantage of this type of view is that
C. 2nd and 3rd each view shows the object all the way
D. 3rd and 4th through as if it were transparent:
A. Planar
16. What type of loci is the diagram below B. Horizontal
C. Auxiliary
D. Orthographic
19. What is the name given to the locus of a
A. Archimedean spiral point on the end of a string as it is unwound
B. epicycloid from a circle?
C. hypocycloid A. cycloid
D. ellipse B. ellipse
C. Helix
17. Which of the following are equal in area D. involute
to triangle ABC in the drawing below?
20. The top, front, and bottom views align in
this manner:
A. Horizontally
B. Vertically
C. According to the planar views
D. Parallel to the frontal plane

Section B (Part I)
Answer all questions

With the aid of annotated diagram, explain the following types of drawing

I．Isometric drawing
II．Perspective drawing
III．Oblique drawing

CONSTRUCTION
Answer only 2 in this section
1. The pictorial view of a sliding block is shown below. Draw in the first angle projection, the
full size of the following views, with hidden details:
I．front elevation in the direction of arrow K;
II．plan;
III．end elevation in the direction of arrow P.
2. Construct in full size the isometric view of he the block shown below

3. Draw the auxiliary top view of a square prism of side 30mm and axis heights of 60 mm with
its axis inclined at 45 H.P and parallel to V.P. Two sides of base are perpendicular to V.P and
parallel to V.P.

Note: Use full scale for all your construction works and dimensions should be in millimeters.
A well established border line and title block make up 20% mark in this section.
All construction lines must be shown clearly. Accuracy and good draughtsmanship are essential.