➢ CMOS

• CMOS (complementary metal-oxide

semiconductor) is the semiconductor
technology used in the transistors that
are manufactured into most of today's
computer microchips.
• It's a technology used in the fabrication of integrated circuits
(ICs), particularly for digital logic circuits and microprocessors.
• In CMOS technology, both kinds of transistors are used in a
complementary way to form a current gate that forms an
effective means of electrical control.
CMOS (Complementary Metal Oxide Semiconductor)
CMOS technology utilizes both PMOS (P-channel Metal-Oxide-Semiconductor)
and NMOS (N-channel Metal-Oxide-Semiconductor) transistors on the same
chip.
CMOS (Complementary Metal Oxide Semiconductor)
These transistors are configured in a complementary manner, meaning that
one type of transistor is used for the high voltage state (logic 1) and the other
type for the low voltage state (logic 0).
CMOS (Complementary Metal Oxide Semiconductor)
This complementary arrangement allows CMOS circuits to have very low
power consumption because power is only consumed during transitions
between logic states, minimizing static power dissipation.
 CMOS (Complementary Metal Oxide
Semiconductor)
• The main advantage of CMOS over NMOS and BIPOLAR technology is the much
smaller power dissipation.
• Unlike NMOS or BIPOLAR circuits, a Complementary MOS circuit has almost no
static power dissipation.
• Power is only dissipated in case the circuit actually switches. This allows the
integration of more CMOS gates on an IC than in NMOS or bipolar technology,
resulting in much better performance. Complementary Metal Oxide
Semiconductor transistor consists of P-channel MOS (PMOS) and N-channel
MOS (NMOS).
• CMOS technology is widely used in a variety of electronic devices, including
microprocessors, memory chips, digital cameras, and many others, due to its low
power consumption, high noise immunity, and scalability to smaller feature sizes,
which allows for increased integration density and improved performance.
Power Supply for CMOS
➢ NMOS
• NMOS is built on a p-type substrate with
n-type source and drain diffused on it.
In NMOS, the majority of carriers are electrons. NMOS Transist
• When a high voltage is applied to the gate, the NMOS will
conduct.
• Similarly, when a low voltage is applied to the gate, NMOS will
not conduct. NMOS is considered to be faster than PMOS,
since the carriers in NMOS, which are electrons, travel twice as
fast as the holes.
➢ PMOS

• P- channel MOSFET consists of P-type Source and Drain

diffused on an N-type substrate.
• The majority of carriers are holes. When a high voltage is
applied to the gate, the PMOS will not conduct. When a low
voltage is applied to the gate, the PMOS will conduct.
• The PMOS devices are more immune to noise than NMOS
devices.
➢ CMOS Working Principle

• In CMOS technology, both N-type and P-type transistors are

used to design logic functions.
• The same signal which turns ON a transistor of one type is used
to turn OFF a transistor of the other type.
• This characteristic allows the design of logic devices using only
simple switches, without the need for a pull-up resistor.
➢ CMOS Working Principle
➢ CMOS Working Principle
➢ CMOS Working Principle
➢ CMOS Working Principle
• In CMOS logic gates a collection of n-type
MOSFETs is arranged in a pull-down network
between the output and the low voltage power
supply rail (Vss or quite often ground).
• Instead of the load resistor of NMOS logic
gates, CMOS logic gates have a collection of
p-type MOSFETs in a pull-up network
between the output and the higher-voltage rail
(often named Vdd).
CMOS using Pull Up & Pull Down
➢ CMOS Working Principle

• Thus, if both a p-type and n-type transistor have their gates

connected to the same input, the p-type MOSFET will be ON
when the n-type MOSFET is OFF, and vice-versa.
• The networks are arranged such that one is ON and the other
OFF for any input pattern as shown in the figure below.
• CMOS offers relatively high speed, low power dissipation, high
noise margins in both states, and will operate over a wide range
of source and input voltages (provided the source voltage is
fixed).
➢ CMOS Inverter
• The inverter circuit as shown in the figure below. It
consists of PMOS and NMOS FET. The input A
serves as the gate voltage for both transistors.
• The NMOS transistor has input from Vss (ground)
and the PMOS transistor has input from Vdd.
• The terminal Y is output. When a high voltage (~
Vdd) is given at input terminal (A) of the inverter, the CMOS Inverter
PMOS becomes an open circuit, and NMOS
switched OFF so the output will be pulled down to
Vss.
➢ CMOS Inverter
➢ CMOS Inverter
➢ CMOS Inverter
• When a low-level voltage (<Vdd, ~0v) applied to the
inverter, the NMOS switched OFF and PMOS switched
ON. So the output becomes Vdd or the circuit is pulled up
to Vdd.

INPUT LOGIC INPUT OUTPUT LOGIC OUTPUT

0V 0 VDD 1
VDD 1 0 V 0
➢ CMOS NAND Gate
• figure shows a 2-input Complementary MOS
NAND gate. It consists of two series NMOS
transistors between Y and Ground and two
parallel PMOS transistors between Y and VDD.
• If either input A or B is logic 0, at least one of
the NMOS transistors will be OFF, breaking the
path from Y to Ground. But at least one of the
pMOS transistors will be ON, creating a path
from Y to VDD Two Input NAND Gate
➢ CMOS NAND Gate
➢ CMOS NAND Gate
➢ CMOS NAND Gate
➢ CMOS NAND Gate
➢ CMOS NAND Gate
• the output Y will be high. If both inputs are high, both of the
nMOS transistors will be ON and both of the pMOS transistors
will be OFF. Hence, the output will be logic low.
• The truth table of the NAND logic gate given in the below table.

A B Pull-Down Network Pull-up Network OUTPUT (Y)

0 0 OFF ON 1

0 1 OFF ON 1

1 0 OFF ON 1

1 1 ON ON 0
➢ CMOS NOR Gate
• A 2-input NOR gate is shown in the
figure below. The NMOS transistors are
in parallel to pull the output low when
either input is high.
• The PMOS transistors are in series to
pull the output high when both inputs are
low, as given in the below table. The
output is never left floating.
Two Input NOR Gate
➢ CMOS NOR Gate
➢ CMOS Characteristics
• The most important characteristics of CMOS are low static power utilization, huge noise
immunity. When the single transistor from the pair of MOSFET transistor is switched OFF
then the series combination uses significant power throughout switching among the two
stated like ON & OFF.
• As a result, these devices do not generate waste heat as compared with other types of
logic circuits such as TTL or NMOS logic, which usually use some standing current even
they don’t change their state.
• These CMOS characteristics will allow for integrating logic functions with high density on
an integrated circuit. Because of this, CMOS has become the most frequently used
technology to be executed within VLSI chips.
• The phrase MOS is a reference to the MOSFET’s physical structure which includes an
electrode with a metal gate that is located on the top of an oxide insulator of
semiconductor material.
• A material like Aluminum is used only once however the material is now polysilicon. The
designing of other metal gates can be done using a comeback through the arrival of high-
κ dielectric materials within the process of the CMOS process.
➢ The advantages of CMOS
• The main benefits of CMOS over TTL are good noise margin as
well as less power consumption. This is due to no straight
conducting lane from VDD to GND, fall times based on the
conditions of input, then the transmission of the digital signal will
become easy & low cost through CMOS chips.
• CMOS is used to explain the amount of memory on the
motherboard of the computer that will store in the settings of
BIOS. These settings mainly include the date, time, and settings
of hardware
TTL is a digital logic circuit where bipolar transistors work on
DC pulses. Several transistor logic gates are normally made-up
of a single IC.
➢ The advantages of CMOS
• It uses a single power supply like + VDD
• These gates are very simple
• Input impedance is high
• CMOS logic uses less power whenever it is held in a set state
• Power dissipation is negligible
• Fan out is high
• TTL compatibility
• Stability of temperature
• Noise immunity is good
• Compact
• Designing is very well
• Robust mechanically
• Logic swing is large (VDD)
➢ The disadvantages of CMOS
• The cost will be increased once the processing steps increases,
however, it can be resolved.
• The packing density of CMOS is low as compared with NMOS.
• MOS chips should be secured from getting static charges by placing
the leads shorted otherwise; the static charges obtained within leads
will damage the chip. This problem can be solved by including
protective circuits otherwise devices.
• Another drawback of the CMOS inverter is that it utilizes two
transistors as opposed to one NMOS to build an inverter, which
means that the CMOS uses more space over the chip as compared
with the NMOS. These drawbacks are small due to the progress
within the CMOS technology.
➢ CMOS Applications
• CMOS technology has been used for the
following digital IC designs.
• Computer memories, CPUs
• Microprocessor designs
• Flash memory chip designing
• Used to design application-specific integrated
circuits (ASICs)