ENGINEERING LIMITED USE

Material Specification
STANDARDS EDS-M-6687

Self-Adhesive Damping Pad

Do Not Use on New Program; No Note: ,
Replacement. Program .

1
1 Scope 1.1 .
1.1 Purpose. This specification specifies the (Self-Adhesive Damping Pad)
requirements of basic property of the self -
.
adhesive damping pad used for the body of
automobiles. 1.2 .
1.2 Typical Applications. This specification (Butyle Rubber)
applies to the self adhesive damping pad, a butyl
rubber pad with aluminum foil on its back, which is (Self-Adhesive Damping Pad)
used for the roof panel, etc. of automobiles. .

2 References 2 /
Note: Only the latest approved standards are :
applicable unless otherwise specified.
.
2.1 External Standards/Specifications.
2.1 / .
None
None
2.2 GM Standards/Specifications.
2.2 GM / .
EDS-M-0102 EDS-T-7624
EDS-T-7602 EDS-T-7633 EDS-M-0102 EDS-T-7624
EDS-T-7603 EDS-T-7694 EDS-T-7602 EDS-T-7633

--```,`,,,,,```,`,,,```-`-`,,`,,`,`,,`---
EDS-T-7609 GMW3059 EDS-T-7603 EDS-T-7694
EDS-T-7611 GMW15174 EDS-T-7609 GMW3059
EDS-T-7611 GMW15174
2.3 Additional References.
TMC003 Material Safety Data Sheet guidance 2.3 / .
documents TMC003 Material Safety Data Sheet guidance
documents
3 Requirements
3.1 General Properties. 3
3.1 .

Table 1: General Properties /

1:
Designations / Test Methods / Specifications /

2
3.1.1 Weight per unit area. / EDS-T-7611 (3.5 0.3) kg/m .
.
3.1.2 Thickness. / EDS-T-7624-1A (2.0 0.2) mm
.

© Copyright 2011 General Motors Company All Rights Reserved

May 2011 Originating Department: GM Korea Engineering Standards Page 1 of 5

Version : 2
Provided by IHS Sold to:COPLAC DO BRASIL LTDA, 01902407
No reproduction or networking permitted without license from IHS Not for Resale,2012/3/14 16:50:9 GMT
 GM KOREA ENGINEERING STANDARDS EDS-M-6687

Designations / Test Methods / Specifications /

3.1.3 Structure/
.
3.1.3.1 Rubber. /
.
3.1.3.1.1 Material. / Butyl rubber. /
. .
3.1.3.2 Aluminum foil. /
.
2
3.1.3.2.1 Weight per unit area. / 190 ~ 200 g/m .
.
3.1.3.2.2 Thickness. / 0.07 mm.
.
3.1.4 Tests on the smelted damping pad (Current
electro-deposition steel sheet, 145 , 30
minutes). /
( ,
145 , 30 ).
3.1.4.1 Low temperature resistance. / EDS-T-7633 No peeling-off from test panel, crack
. or break. /

.
Test temperature: (-30) ./
: (-30) .
Falling height: 0.5 m. /
: 0.5 m
3.1.4.2 Resistance to heat: Leave test piece in a No peeling-off from test panel or
145 oven for 3 hours in a roof style where sliding from initial position. /
damping pad faces downward. /
: .
145 , 3 .
Size of test piece: (200 × 150) mm. /
: (200 × 150) mm.
3.1.4.3 Resistance to peeling. / EDS-T-7609 Peeling-off allowed only by
. destruction. (Peeling-off of aluminum
foil from damping pad is allowed). /

(
).
3.1.4.4 Resistance to odor. / EDS-T-7603
.
3.1.4.4.1 A2. Rating 5 min. /
5 .
3.1.4.4.2 B2. Rating 5 min. /
5 .
© Copyright 2011 General Motors Company All Rights Reserved

May 2011 Page 2 of 5

Version : 2 --```,`,,,,,```,`,,,```-`-`,,`,,`,`,,`---

Provided by IHS Sold to:COPLAC DO BRASIL LTDA, 01902407

No reproduction or networking permitted without license from IHS Not for Resale,2012/3/14 16:50:9 GMT
 GM KOREA ENGINEERING STANDARDS EDS-M-6687

Designations / Test Methods / Specifications /

3.1.4.5 Volatility of organic constituents. / EDS-T-7694

.
Reflectance. / 60 % min. /
. 60 % .
3.1.4.6 Flammability. / EDS-T-7602
.
Burn rate. / 90 mm/min max. /
. 90 mm/min .
3.1.4.7 Loss Factor Measurement. / GMW15174-4.3.8
.
3.1.4.7.1 (-20) 0.07 min /
0.07 .
3.1.4.7.2 (-10) 0.08 min /
0.08 .
3.1.4.7.3 0 0.11 min /
0.11 .
3.1.4.7.4 +10 0.17 min /
0.17 .
3.1.4.7.5 +20 0.28 min /
0.28 .
3.1.4.7.6 +30 0.30 min /
0.30 .
3.1.4.7.7 +40 0.20 min /
0.20 .
3.1.4.7.8 +50 0.12 min /
0.12 .
3.1.4.7.9 +60 0.09 min /
0.09 .

3.2 Additional Requirements 3.2

3.2.1 Release paper. It shall be easily separated 3.2.1 .
as intended by workers or the manufacturer. .
3.2.2 Appearance. It shall be free from defects
3.2.2 . ,
such as blister, crack and pollution by foreign
matters and shall conform to the master sample ,
approved and released by GM Korea Technical .
Center. 3.2.3 .
3.2.3 For further details, see parts drawings.
4
4 Manufacturing Process .
Not applicable.

© Copyright 2011 General Motors Company All Rights Reserved

May 2011 Page 3 of 5

Version : 2 --```,`,,,,,```,`,,,```-`-`,,`,,`,`,,`---

Provided by IHS Sold to:COPLAC DO BRASIL LTDA, 01902407

No reproduction or networking permitted without license from IHS Not for Resale,2012/3/14 16:50:9 GMT
 GM KOREA ENGINEERING STANDARDS EDS-M-6687

5 Rules and Regulations 5

5.1 Legal Regulations. All materials must satisfy 5.1 .
applicable laws, rules, regulations and , , ,
recommendations valid in the country of usage.
.
5.2 Language. In the event of conflict between the
Korean and English language, the Korean 5.2 . ,
language shall take precedence. .
5.3 Inspection and Rejection. Samples of 5.3 . GM
components or materials released to a GM
material specification shall be tested for conformity ,
with the requirements of this material specification .
and approved by the responsible Engineering
department prior to commencement of delivery of , , , /
bulk supplies. ,
A new approval must be received for any changes, . ,
e.g., properties, manufacturing process, location of
manufacture, etc. If not otherwise agreed, all .
testing and documentation normally required for
initial release must be completed.
/
It is the responsibility of the supplier to inform the ,
customer in a timely manner, without solicitation,
.
and to include documentation of all modifications of
materials and/or processes and to apply for a new ,
release.
If not otherwise agreed, all release tests shall be .
repeated and documented by the supplier prior to
commencement of delivery of non-conforming bulk .
supplies. In individual cases, a shorter test can be
agreed to between the responsible Engineering
department and the supplier.
5.4 Initial Source Approval. No shipments shall 5.4 .
be made by any supplier until representative initial
production samples have been approved by the
appropriate Materials Engineering department(s) .
as meeting the requirements of this specification.
5.5 Material Safety Data Sheets/Safety Data
Sheets (MSDS/SDS). For new product 5.5 / (MSDS/SDS).
submissions, or when a change in chemical
composition of an existing product has occurred, a ,
complete copy of the Material Safety Data (GHS)
Sheet/Safety Data Sheet must be submitted in /
compliance with the Globally Harmonized System /
of Classification and Labeling of Chemicals (GHS) .
requirements or other country-specific MSDS/SDS
/ GM
requirements. In addition, product MSDS/SDS
submissions must be in compliance with specific /
country General Motors TMC003 Material Safety TMC003 .
Data Sheet/Safety Data Sheet guidance
documents where available.
5.6 All materials supplied to this standard must 5.6 GMW3059
comply with the requirements of GMW3059,
( ) .
Restricted and Reportable Substances for
Parts.

© Copyright 2011 General Motors Company All Rights Reserved

May 2011 Page 4 of 5

--```,`,,,,,```,`,,,```-`-`,,`,,`,`,,`---

Version : 2
Provided by IHS Sold to:COPLAC DO BRASIL LTDA, 01902407
No reproduction or networking permitted without license from IHS Not for Resale,2012/3/14 16:50:9 GMT
 GM KOREA ENGINEERING STANDARDS EDS-M-6687

6 Approved Sources 6
Engineering qualifications of an approved source
are required for this standard. Only sources listed .
in the GM Materials File under this standard
GM
number have been qualified by Engineering as
meeting the requirements of this standard. .
For other GM locations, the responsible GM ,
Engineering group should be contacted to obtain
the approved source in that individual country. .
6.1 Approval and Quality Assurance Procedure. 6.1 .
All raw materials shall be approved and regularly
inspected for its quality prior to and during mass (EDS-M-0102)
production delivery according to approval and
.
quality assurance procedure for chemical raw
materials (Spec. No. EDS-M-0102).

7 Notes 7
7.1 Glossary. Not applicable. 7.1 . .
7.2 Acronyms, Abbreviations, and Symbols. 7.2 .
GHS Globally Harmonized System GHS Globally Harmonized System
MSDS Material Safety Data Sheet MSDS Material Safety Data Sheet
SDS Safety Data Sheet SDS Safety Data Sheet

8 Coding System 8
This standard shall be referenced in other
documents, drawings, etc., as follows:
.
Material per EDS-M-6687
Material per EDS-M-6687
9 Release and Revisions
This standard was originated in May 2009. It was
9
first approved by Engineering Standard Committee 2009 5 ,
in May 2009. It was first published in May 2009. 2009 5 .
2009 5 / .

Issue / Publication Date / Description (Organization) /

( )
2 MAY 2011 Apply new Engineering Standard Template.
Limited use with no replacement (ME Paint M&F Engineering team) /
.
( ) ( )

© Copyright 2011 General Motors Company All Rights Reserved

May 2011 Page 5 of 5

Version : 2 --```,`,,,,,```,`,,,```-`-`,,`,,`,`,,`---

Provided by IHS Sold to:COPLAC DO BRASIL LTDA, 01902407

No reproduction or networking permitted without license from IHS Not for Resale,2012/3/14 16:50:9 GMT