TVS Diodes

Axial Leaded – 600W > P6KE series

P6KE Series RoHS Pb e3

Description

The P6KE Series is designed specifically to protect

Bi-directional sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.

Features

• 600W peak pulse • Typical IR less than 1μA

Uni-directional capability at 10/1000μs when VBR min>12V
waveform, repetition rate • Compatible with high
(duty cycles):0.01% temperature reflow
• Glass passivated chip soldering (260°C/30 s)
junction in DO-15 Package • VBR @ TJ= VBR@25°C
Agency Approvals • Fast response time: x (1+ĮT x (TJ - 25))
typically less than 1.0ps (ĮT:Temperature
Agency Agency File Number from 0 Volts to BV min Coefficient, typical value
• Excellent clamping is 0.1%)
E230531
capability • UL Recognized epoxy
• Typical failure mode is meeting flammability
Maximum Ratings and Thermal Characteristics short from over-specified classification V-0
(TA=25OC unless otherwise noted) voltage or current • Matte tin lead–free plated
• Whisker test conducted • Halogen free and RoHS
Parameter Symbol Value Unit based on Table 4a and 4c compliant
Peak Pulse Power Dissipation(Fig.2) by 10/1000us of JEDEC JESD201A • Pb-free E3 means 2nd
Test Waveform(Fig.4)(Note 1) PPPM 600 W
-Single Die Parts
• IEC 61000-4-2 ESD level interconnect is Pb-
Peak Pulse Power Dissipation(Fig.2) by 30kV(Air), 30kV (Contact) free and the terminal finish
10/1000us Test Waveform(Fig.4)(Note 1) PPPM 800 W • EFT protection of data material is tin(Sn) (IPC/
-Stacked Die Parts(Note 4) JEDEC J-STD-609A.01)
lines in accordance with
Steady State Power Dissipation on Infinite Heat
Sink at TL=75ºC
PD 5.0 W IEC 61000-4-4
Peak Forward Surge Current, 8.3ms Single Half • Low incremental surge
IFSM 100 A
Sine Wave Unidirectional Only (Note 2) resistance
Maximum Instantaneous Forward Voltage at 50A
VF 3.5/5.0 V
for Unidirectional Only (Note 3)
Operating Junction and Storage Temperature
TJ , TSTG -55 to 175 °C
Range
Typical Thermal Resistance Junction to Lead R‫ڧ‬JL 20 °C/W Applications
Typical Thermal Resistance Junction to Ambient R‫ڧ‬JA 75 °C/W TVS components are ideal for the protection of I/O
Notes: interfaces, VCC bus and other vulnerable circuits used in
1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) = 25OC per Fig. 3.
2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum.
telecom, computer, industrial and consumer electronic
3. VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. applications.
4. For stacked die component details, please refer to part numbers labeled by * in Electrical Characteristics.

Functional Diagram Additional Infomarion

Bi-directional Datasheet Resources Samples

Cathode Anode

Uni-directional

© 2020 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.10/26/20
 TVS Diodes
Axial Leaded – 600W > P6KE series

Electrical Characteristics (T =25°C unless otherwise noted)

A

Breakdown Test Maximum

Maximum Maximum Agency
Part Part Reverse Stand Voltage VBR Current Reverse
Clamping Peak Approval
Number Number off Voltage VR IT Leakage
(Volts) @ IT Voltage Pulse Current
(Uni) (Bi) (Volts) I R@ V R
(mA) VC @ Ipp (V) Ipp (A)
Min. Max. (µA)
P6KE6.8A P6KE6.8CA 5.80 6.45 7.14 10 10.5 58.1 1000 X
P6KE7.5A P6KE7.5CA 6.40 7.13 7.88 10 11.3 54.0 500 X
P6KE8.2A P6KE8.2CA 7.02 7.79 8.61 10 12.1 50.4 200 X
P6KE9.1A P6KE9.1CA 7.78 8.65 9.55 1 13.4 45.5 50 X
P6KE10A P6KE10CA 8.55 9.50 10.50 1 14.5 42.1 10 X
P6KE11A P6KE11CA 9.40 10.50 11.60 1 15.6 39.1 5 X
P6KE12A P6KE12CA 10.20 11.40 12.60 1 16.7 36.5 5 X
P6KE13A P6KE13CA 11.10 12.40 13.70 1 18.2 33.5 1 X
P6KE15A P6KE15CA 12.80 14.30 15.80 1 21.2 28.8 1 X
P6KE16A P6KE16CA 13.60 15.20 16.80 1 22.5 27.1 1 X
P6KE18A P6KE18CA 15.30 17.10 18.90 1 25.2 24.2 1 X
P6KE20A P6KE20CA 17.10 19.00 21.00 1 27.7 22.0 1 X
P6KE22A P6KE22CA 18.80 20.90 23.10 1 30.6 19.9 1 X
P6KE24A P6KE24CA 20.50 22.80 25.20 1 33.2 18.4 1 X
P6KE27A P6KE27CA 23.10 25.70 28.40 1 37.5 16.3 1 X
P6KE30A P6KE30CA 25.60 28.50 31.50 1 41.4 14.7 1 X
P6KE33A P6KE33CA 28.20 31.40 34.70 1 45.7 13.3 1 X
P6KE36A P6KE36CA 30.80 34.20 37.80 1 49.9 12.2 1 X
P6KE39A P6KE39CA 33.30 37.10 41.00 1 53.9 11.3 1 X
P6KE43A P6KE43CA 36.80 40.90 45.20 1 59.3 10.3 1 X
P6KE47A P6KE47CA 40.20 44.70 49.40 1 64.8 9.4 1 X
P6KE51A P6KE51CA 43.60 48.50 53.60 1 70.1 8.7 1 X
P6KE56A P6KE56CA 47.80 53.20 58.80 1 77.0 7.9 1 X
P6KE62A P6KE62CA 53.00 58.90 65.10 1 85.0 7.2 1 X
P6KE68A P6KE68CA 58.10 64.60 71.40 1 92.0 6.6 1 X
P6KE75A P6KE75CA 64.10 71.30 78.80 1 103.0 5.9 1 X
P6KE82A P6KE82CA 70.10 77.90 86.10 1 113.0 5.4 1 X
P6KE91A P6KE91CA 77.80 86.50 95.50 1 125.0 4.9 1 X
P6KE100A P6KE100CA 85.50 95.00 105.00 1 137.0 4.5 1 X
P6KE110A P6KE110CA 94.00 105.00 116.00 1 152.0 4.0 1 X
P6KE120A P6KE120CA 102.00 114.00 126.00 1 165.0 3.7 1 X
P6KE130A P6KE130CA 111.00 124.00 137.00 1 179.0 3.4 1 X
P6KE150A P6KE150CA 128.00 143.00 158.00 1 207.0 2.9 1 X
P6KE160A P6KE160CA 136.00 152.00 168.00 1 219.0 2.8 1 X
P6KE170A P6KE170CA 145.00 162.00 179.00 1 234.0 2.6 1 X
P6KE180A P6KE180CA 154.00 171.00 189.00 1 246.0 2.5 1 X
P6KE200A P6KE200CA 171.00 190.00 210.00 1 274.0 2.2 1 X
P6KE220A P6KE220CA 185.00 209.00 231.00 1 328.0 1.9 1 X
P6KE250A - 214.00 237.00 263.00 ¹ 344.0 1.8 1 X
P6KE250CA* 214.00 237.00 263.00 1 344.0 2.4 1 X
P6KE300A - 256.00 285.00 315.00 1 414.0 1.5 1 X
P6KE300CA* 256.00 285.00 315.00 1 414.0 2.0 1 X
P6KE350A* P6KE350CA* 300.00 332.00 368.00 1 482.0 1.7 1 X
P6KE400A* P6KE400CA* 342.00 380.00 420.00 1 548.0 1.5 1 X
P6KE440A* P6KE440CA* 376.00 418.00 462.00 1 602.0 1.4 1 X
P6KE480A* P6KE480CA* 408.00 456.00 504.00 1 658.0 1.3 1 X
P6KE510A* P6KE510CA* 434.00 485.00 535.00 1 698.0 1.2 1 X
P6KE530A* P6KE530CA* 451.00 503.50 556.50 1 725.0 1.2 1 X
P6KE540A* P6KE540CA* 460.00 513.00 567.00 1 740.0 1.1 1 X
P6KE550A* P6KE550CA* 468.00 522.50 577.50 1 760.0 1.1 1 X
P6KE600A* P6KE600CA* 512.00 570.00 630.00 1 828.0 1.0 1 -

For bidirectional type having VR of 10 volts and less, the IR limit is double.
For parts without A , the VBR is ± 10% and VC is 5% higher than with A parts, the parts without A are currently available, but not recommended for new designs. The parts with A are preferred.
For stack-die parts, use * to label the part number.

© 2020 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.10/26/20
 TVS Diodes
Axial Leaded – 600W > P6KE series

I-V Curve Characteristics

Uni-directional Bi-directional

Ipp

IT
Vc VBR VR Vc VBR VR IR
V V
IR VF IR VR VBR Vc
IT IT

Ipp
Ipp

PPPM Peak Pulse Power Dissipation -- Max power dissipation

VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
VBR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
VC Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current)
IR Reverse Leakage Current -- Current measured at VR
VF Forward Voltage Drop for Uni-directional

Ratings and Characteristic Curves (T =25°C unless otherwise noted)

A

Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating

Voltage Transients 100

TJ initial = TAMB
PPPM-Peak Pulse Power (kW)

Voltage Across TVS 10 stacked-die, 800W

at 10/1000µs, 25°C
Voltage or Current

Current Through TVS

1 Single die,600W
at 10/1000µs, 25°C

0.1
0.001 0.01 0.1 1 10

td-Pulse Width (ms)

Time

© 2020 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.10/26/20
 TVS Diodes
Axial Leaded – 600W > P6KE series

Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A

Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform

150
100 tr=10µsec
Peak Pulse Power (PPP) or Current (IPP)

TJ=25°C

IPPM- Peak Pulse Current, % IRSM

Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
Peak Value
Derating in Percentage %

75 IPPM
100

Half Value
50
( )
IPPM IPPM
2

50 10/1000µsec. Waveform
25 as defined by R.E.A

0 td
0 25 50 75 100 125 150 175 200 0
0 1.0 2.0 3.0 4.0
TJ - Initial Junction Temperature (ºC) t-Time (ms)

Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance

100
10000.00
Transient Thermal Impedance ( °C/W)

Uni-dire onal V= 0V

1000.00 Bi-direc nal V=0V

10
Cj(pf)

100.00
Uni-dire onal
Bi-direc nal
V= VR 1
10.00

1.00
1.00 10.00 100.00 1000.00 0.1
VBR—Reverse Breakdown Voltage(V) 0.01 0.1 1 10 100 1000
TP - Pulse Duration (s)

Figure 7 - Maximum Non-Repetitive Peak Forward Figure 8 - Peak Forward Voltage Drop vs Peak Forward
Surge Current Uni-Directional Only Current (Typical Values)

120 100.0
Single die
IFSM - Peak Forward Surve Current(A)

100
IF - Peak Forward Current(A)

80 10.0 Stacked-die

60

40
1.0

20

0
1 10 100
0.1
Number of Cycles at 60 Hz 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0
VF - Peak Forward Voltage(V)

© 2020 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.10/26/20
 TVS Diodes
Axial Leaded – 600W > P6KE series

Soldering Parameters

Reflow Condition Lead–free assembly

tp
- Temperature Min (Ts(min)) 150°C TP

Pre Heat - Temperature Max (Ts(max)) 200°C Ramp-up Critical Zone

TL to TP
- Time (min to max) (ts) 60 – 120 secs TL tL

Temperature (T)
Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max Ts(max)

TS(max) to TL - Ramp-up Rate 3°C/second max Ramp-down

Ts(min)
- Temperature (TL) (Liquidus) 217°C ts
Reflow Preheat
- Time (min to max) (tL) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C 25˚C
t 25˚C to Peak
Time within 5°C of actual peak Temperature (tp) 30 Seconds Max Time (t)
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C Flow/Wave Soldering (Solder Dipping)

Peak Temperature : 265OC

Dipping Time : 10 seconds
Soldering : 1 time

Physical Specificationst C Environmental Specifications

Weight 0.015oz., 0.4g High Temp. Storage JESD22-A103

JEDEC DO-204AC (DO-15) molded plastic body HTRB JESD22-A108
Case
over passivated junction.
Temperature Cycling JESD22-A104
Polarity Color band denotes the cathode except Bipolar.
H3TRB JESD22-A101
Matte Tin axial leads, solderable per RSH JESD22-B106
Terminal
JESD22-B102.

Dimensions
Cathode Band Inches Millimeters
(for uni-directional products only)
D Dimensions
Min Max Min Max
C A 1.000 - 25.40 -
B 0.230 0.300 5.80 7.60
A B A
C 0.028 0.034 0.71 0.86
D 0.104 0.140 2.60 3.60
DO-204AC (DO-15)

© 2020 Littelfuse, Inc.

Specifications are subject to change without notice.
Revised: JC.10/26/20
 TVS Diodes
Axial Leaded – 600W > P6KE series

Part Numbering System Part Marking System

P6KE xxx XX X
Cathode Band
Option Code: (for uni-directional
Blank Reel Tape
products only)

F
-B Bulk Packaging
YYWW
Type Code: Littelfuse Logo Trace Code Marking
A Uni-Directional (5% VBR Voltage Tolerance)
CA Bi-Directional (5% VBR Voltage Tolerance)
YY:Year Code
WW: Week Code
VBR Voltage Code:
(Refer to the Electrical Characteristics table) P6KEXXX Product Type
Series Code

Packaging

Component Packaging
Part Number Quantity Packaging Specification
Package Option
P6KExxxXX DO-204AC 4000 Tape & Reel EIA STD RS-296
P6KExxxXX-B DO-204AC 1000 BULK Littelfuse Spec.

Tape and Reel Specification

Off Center
2.56 2.063+0.079/-0.039
either side
(65.0) (53.0+2.0/-1.0)
0.028(0.7)

0.047 0.236
(1.2) (6.0)
0.197+/-0.020
(5.0+/- 0.5)
Dimensions are in
13.0 inches/mm
(330.2)

3.0
(76.2)

0.68
(17.27)
2.75
(69.85)

Direction of Feed
Recess Depth Max. 0.75 (19.05)

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are
not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics.
© 2020 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: JC.10/26/20