0% found this document useful (0 votes)
32 views15 pages

GTD - 05

This document contains a 20 question mock test for an electrical engineering exam. The test covers topics such as capacitors, matrices, transformers, amplifiers, control systems and more. Students are instructed to answer all questions within 2 hours and submit their responses on an OMR sheet for grading.

Uploaded by

Karthik Bollu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
32 views15 pages

GTD - 05

This document contains a 20 question mock test for an electrical engineering exam. The test covers topics such as capacitors, matrices, transformers, amplifiers, control systems and more. Students are instructed to answer all questions within 2 hours and submit their responses on an OMR sheet for grading.

Uploaded by

Karthik Bollu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Page 1 of 15

MOCK Test for TSTRANSO/TSSPDCL


Paper Code: GTD – 05
Branch: Electrical and Electronics Engineering
Author: BNSS Shankar, M.Tech (IITK), MIE

Note:
1. Answer all questions in two hours. Each question carries one mark.
2. There are no negative marks and you are not allowed to use any calculator.
3. Download OMR sheet from the blog and enter the answers in the OMR sheet with ball
point pen (Black) only so that you can get the same environment as in the final exam.
4. Serious practice of this paper will help you in better way for your preparation.

Section A: Electrical Engineering


01.
1. I leads V by 90° in fig (a)
2. I leads V by 90° in fig (b)
3. I lags V by 90° in fig (a)
4. I lags V by 90° in fig (b)

Which of the given statement(s) is/are true regarding the


capacitors shown in the figure? Fig (a) Fig (b)
(A) 3 only (B) 2 only
(C) 1 and 4 (D) 2 and 3
02.
1 1 3
The Eigen values of the matrix 1 5 1 are
3 1 1
(A) –2, 3 and –6 (B) –2, –3 and –6
(C) –2, 3 and 6 (D) 2, 3 and 6
03.
Load factor of a consumer is 35% and the monthly consumption is 504 kWh. If the rate of
electricity is Rs. 180 per kW of maximum demand plus Rs. 2.00 per kWh, then the monthly bill
of the consumer is
(A) Rs. 1368 (B) Rs. 1008
(C) Rs. 2016 (D) Rs. 684
04.
The number of 2 μF, 400 V capacitors needed to obtain the capacitance value of 1.5 μF rated for
1600 V is
(A) 12 (B) 8
(C) 6 (D) 4
05.
A discrete system is described by yn   xn* xn  . Then system is
(A) causal, linear and time varying (B) causal, nonlinear and time varying
(C) non causal, linear and time varying (D) non causal, nonlinear and time varying

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 2 of 15

06.
A current waveform f t  , shown in the figure is passed through a Moving Iron type ammeter.
Assume the readings are ampere on y – axis and time in second on x – axis are taken for the
measurement. The reading of the ammeter could be

(A) 6A (B) 36 A (C) 6A (D) 0A


07.
In a transformer, eddy current loss is 100 W which is half of the total core loss. If both the
thickness of laminations and frequency are increased by 10%, the new core loss would be
(A) 256.41 W (B) 231 W
(C) 267.41 W (D) 242 W
08.
Triac can be categorized as a
(A) minority carrier, bi polar, bidirectional and fully controlled device
(B) majority carrier, bi polar, bidirectional and fully controlled device
(C) minority carrier, bi polar, bidirectional and semi controlled device
(D) majority carrier, uni polar, bidirectional and semi controlled device
09.
The closed loop system shown in the figure is subjected to a disturbance N(s), the transfer
C s 
function is
N s 
G1 s G2 s 
(A)
1 G1 s G2 s H s 
G1 s 
(B)
1 G1 s H s 
G2  s 
(C)
1 G2 s H s 
G2 s 
(D)
1 G1 s G2 s H s 
10.
While using bipolar junction transistor as an amplifier, the collector and emitter terminals got
interchanged mistakenly. Assuming that the amplifier is a common emitter amplifier and the
biasing is suitably adjusted, the interchange of terminals will result into which one of the
following?
(A) Zero gain (B) Infinite gain
(C) Reduced gain (D) No change in gain at all

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 3 of 15

11.
The conductance per phase in a star connected load is 3 mho. If it is converted into delta system,
then the equivalent conductance per phase in mho is
(A) 9 (B) 1
(C) 6 (D) 1.5
12.
A waveform f t  repeating with an angular frequency ω can be expressed as

a
f t   0   a n cosht   bn sin ht  . If f t  has Odd quarter wave symmetry, then
2 h1
 /2
4
(A) ah  0 For all values of h, bh 
  f t sin ht  d t  for odd h and 0 for even h
0

2
f t sin ht  d t  for odd h and 0 for even h
 0
(B) ah  0 For all values of h, bh 

 /2
4
(C) bh  0 For all values of h, ah 
  f t cosht  d t  for odd h and 0 for even h
0

2
f t cosht  d t  for odd h and 0 for even h
 0
(D) bh  0 For all values of h, ah 

13.
If Ds is the GMR of individual conductors composing the bundle conductor shown in the figure,
the overall GMR of the bundle Dsb is given by
(A) Ds  d (B) 3
Ds  d 2

(C) 1.09  4 Ds  d 3 (D) 4


Ds  d 3

14.
For a transmission line, the voltage regulation can be defined as
VR , NL  VR , FL VR , NL  VR , FL
(A) With VS constant (B) With VR constant
VR , FL VR , FL
VR , NL  VR , FL VS  VR
(C) With VS constant (D) With VR constant
VR , NL VR
15.
s 1
Inverse Laplace transform of is
1
s 
4
t t
 3 
(A)  t   e u t 4
(B)  t   e 4 u t 
4
t t
 3 4
(C) e 4 u t  (D) e u t 
4

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 4 of 15

16.
The following statements are related to DVM (Digital Voltmeter). Which of them is true?
(A) Common mode rejection is the same for ac and dc voltages.
(B) Its accuracy depends on source impedance.
(C) It does not have series mode error.
(D) Use of shunts for dc current measurements increases its accuracy
17.
A 20 kVA, 2300 V/ 230 V, two winding transformer is to be used as an autotransformer to give
2300 V/ 2530 V. Its rating will be
(A) 200 kVA with conducted kVA = 20 (B) 200 kVA with conducted kVA = 180
(C) 220 kVA with conducted kVA = 20 (D) 220 kVA with conducted kVA = 200
18.
In a thyristor, if positive gate current is applied during reverse bias condition
(A) the junction J3 (nearer to gate – cathode) becomes reverse biased
(B) the reverse α1 and α2 being significantly larger than their forward counter parts
(C) the latching of thyristor can occur
(D) OFF state power loss of the device will increase due to increasing of reverse leakage
current
19.
An amplifier has a power gain of 200, what is its gain in dB? ( log10 2  0.30 )
(A) 14 dB (B) 17 dB (C) 20 dB (D) 23 dB
20.
C s   n2
The closed loop transfer function of a unity feedback control system is,  2 .
Rs  s  2 n s   n2
The velocity error constant of the system is
n n
(A) (B)
2 
2 n 3 n
(C) (D)
 2
21.
The phase sequence of 3 – phase balanced delta connected load is abc. By considering the phase
currents I ab , I bc and I ca , line currents Ia, Ib and Ic, then
(A) Ia leads I ab by 30° (B) Ia lags I ab by 30°
(C) I bc leads I ab by 120° (D) I ca lags I ab by 120°
22.
The root mean square value of f t   3 sin 2t  4 cos 2t over the range 0  t   is
(A) 5 (B) 25 (C) 12.5 (D) 12.5
23.
A 2 km long, 3 – core, 3 – phase cable has capacitance 0.5 μF/km between two conductors
bunched with sheath and the third conductor. The capacitance between the conductors is also
measured when bunched together and the sheath and found to be 0.75 μF/km. The capacitance
between phases is
(A) 0.25 μF/km (B) 0.625 μF/km
(C) 0.125 μF/km (D) 0.50 μF/km

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 5 of 15

24.
The Lorentz force law for electric and magnetic fields is given by
(A) f = QE (B) f=v×B
(C) f = Q(E + v × B) (D) f = Q(v × B)
25.
The impulse response hn of the LTI system is hn  un  3  un  2  2un  7
(A) stable but non causal (B) stable and causal
(C) causal but unstable (D) unstable and non causal
26.
The miller sweep circuit normally used in a CRO is basically
(A) a voltage to current converter circuit (B) a current to voltage converter circuit
(C) an integrator circuit (D) a differentiator circuit
27.
A three – phase delta – star transformer has secondary to primary turns ratio per phase of 5. For a
primary voltage of 400 V, the secondary voltage would be
(A) 2000 V (B) 80 V
(C) 3464 V (D) 80 3 V
28.
The IGBT (Insulated Gate Bipolar Transistor) used
in the circuit has the following data:
t ON  3 μs, tOFF  1.2 μs, Duty cycle = 0.7, VCE(sat) =
2 V and fs = 1 kHz. What are the switching power
losses during turn on and turn off respectively
(A) 1.98 W and 1.7 W
(B) 2.2 W and 1.7 W
(C) 1.98 W and 0.792 W
(D) 2.2 W and 0.792 W

29.

The circuit shown in the figure is


(A) low – pass filter
(B) high – pass filter
(C) band – pass filter
(D) band – reject filter

30.
Circular root loci may occur in systems involve
(A) two poles and one zero (B) two poles and two zeros
(C) one pole and two zeros (D) All of the above
31.
A voltage source Ean  120210 V and the current through the source is given by
I na  1060 A. Then the source will
(A) deliver 600 VAR (B) consume 0 VAR
(C) deliver –600 VAR (D) consume –600 VAR

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 6 of 15

32.
d 2 y dy
Particular Integral of   x 2  2 x  4 is
dx2 dx
x2 x3 x3 x3
(A)  4x (B) 4 (C)  4x (D)  4x2
3 3 3 3
33.
For any degree of series compensation, additional capacitive shunt compensation
(A) increases the effective length of the line
(B) increase virtual surge impedance of line
(C) decreases virtual surge impedance loading of line
(D) both B and C
34.
Match List I and List II and select the correct answer using the codes given below the lists.
List I List II
(Expression) (Law/Theorem/Equation)

(P)  2V   1. Gauss’s law

2. Divergence theorem
(Q)  V 0
2
3. Laplace’s equation
(R)  D. ds  Q
S
4. Poisson’s equations
5. Coulomb’s law
(S)  . D dv   D . ds
V S

Codes:
(A) P – 4, Q – 2, R – 5, S – 1 (B) P – 2, Q – 3, R – 4, S – 5
(C) P – 3, Q – 1, R – 2, S – 4 (D) P – 4, Q – 3, R – 1, S – 2
35.
In a 33 kV overhead line, there are three units in the string of insulators. If the capacitance
between each insulator pin and earth is 11% of self capacitance of each insulator, then the string
efficiency is
(A) 85.8% (B) 68%
(C) 87% (D) 94%
36.
In case of power measurements by the two wattmeter method in a balanced 3 – phase system
with a pure inductive load
(A) both watt meters will indicate the same value but of opposite sign.
(B) both watt meters will indicate zero.
(C) both watt meters will indicate the same value and of the same sign.
(D) one wattmeter will indicate zero and the other will indicate some non zero value.
37.
The residual magnetism of a self excited dc generator is lost. To build up its emf again
(A) The field winding must be replaced
(B) The armature connection must be reversed
(C) The field winding connection must be reversed
(D) field winding must be excited by a low voltage dc supply

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 7 of 15

38.
A battery is charged by a single phase half wave diode rectifier. The supply voltage is 200 V
(rms), 50 Hz and the battery emf is constant at 100 V. If the diode has voltage drop of 2 V during
its conduction, then PIV rating of the diode should be
(A) 382.84 V (B) 384.84 V
(C) 302 V (D) 502 V
39.
What is the effect of cascading the amplifier stages?
(A) To increase the voltage gain and increase the bandwidth
(B) To increase the voltage gain and reduce the bandwidth
(C) To decrease the voltage gain and increase the bandwidth
(D) To decrease the voltage gain and reduce the bandwidth
40.
The critical value of gain for a system is 40. The system is operating at a gain of 20. The gain
margin of the system is
(A) 2 dB (B) 3 dB (C) 6 dB (D) 4 dB
41.

In the network shown in the figure, the power


consumed by 5 Ω resistor is
(A) 180 W
(B) 360 W
(C) 405 W
(D) 675 W

42.
If the correlation coefficient is 0, then the two regression lines are
(A) parallel (B) perpendicular
(C) coincident (D) inclined at 45° to each other
43.
The detailed representation of a regulating transformer
used in power systems is shown in the figure. The
admittance Y in p.u is shown on the side of the ideal
transformer nearest to that node j. Assume the tap is on
the side of node i so that the transformation ratio is a : 1
(from i  j ). The regulating transformer is modeled as
 Ii  Vi 
 I   YBUS V  then YBUS =
 j  j
 Y Y 
 2 
 Y  aY  a *
(A)  a *Y (B) a 
a Y 
2
  Y 
  a Y 

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 8 of 15

 Y
 Y 
a Y  a *Y  a
2

(C)   (D)  Y Y 
  aY Y   2

 a * a 
44.
Lifting power of an electric magnet is proportional to
(A) Current in the operating coil (B) magnetic flux density
(C) square of the magnetic flux density (D) permeability of the core
45.
A 240 V dc series motor takes 40 A when giving its rated output at 1500 rpm. Its resistance is 0.3
Ω. The value of resistance which must be added to obtain rated torque at 1000 rpm is
(A) 6Ω (B) 5.7 Ω (C) 2.2 Ω (D) 1.9 Ω
46.
A PMMC 0 – 10 A ammeter is not provided with any controlling mechanism and the moving
parts are free to rotate. If a current of 1 dc is passed through the moving coil, then the instrument
(A) will read 1 A (B) will read 10 A
(C) pointer will continuously rotate (D) pointer will remain stationary
47.
In all rotating electrical machines, electrical torque is developed when relative speed between
stator field and rotor field is
(A) zero (B) equal to rotor speed
(C) equal and opposite to rotor speed (D) depend upon the type of electrical machine
48.
A single phase full wave diode bridge rectifier is supplied from 230 V, 50 Hz source. The load
consists of R = 10 Ω and a large inductance so as to render the load current constant. The RMS
value of fundamental source current is
(A) 20.71 A (B) 26.37 A (C) 18.64 A (D) 25.3 A
49.
An example of a self complementing code is
(A) 8421 code (B) 7421 code
(C) excess – 3 code (D) gray code
50.
100s  15
The transfer function of a linear control system is given by G s   . In its Bode
ss  4s  10
diagram, the value of gain for   0.1 rad/s is
(A) 20 dB (B) 40 dB (C) 60 dB (D) 80 dB
51.
In a network with 500 nodes and 700 branches, the number of tree branches and links,
respectively are
(A) 499 and 200 (B) 499 and 201 (C) 201 and 499 (D) 200 and 499
52.
2 3
The probability that A passes an exam is and the probability that B passes the same exam is .
3 5
The probability that only one of them passes is
2 4 2 7
(A) (B) (C) (D)
5 15 15 15

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 9 of 15

53.
In Newton-Raphson load flow technique, the power flow equation can be expressed as
 H L      P 
 M N   V   Q  Where H, L, M and N are the sub-matrices of Jacobian matrix. Then, the
   V   
off-diagonal elements of L are equal to
(A) off-diagonal elements of H
(B) off-diagonal elements of M
(C) negatives of off-diagonal elements of H
(D) negatives of off-diagonal elements of M
54.
2
 
If the Fourier transform X e j of xn is zero for
3
    , then minimum sampling rate
2
s  should be
N
2 2 2  2 
(A)  (B)  2 
N 5 N  5 
2  2  2
(C)  2  (D)  4
N  5  N
55.
Three equal impedances of j 21 Ω are connected in Δ. The sequence impedances of the circuit
are
(A) Z 0  j 21 Ω, Z 1  j 21 Ω and Z 2  j 21 Ω
(B) Z 0  0 Ω, Z 1  j 21 Ω and Z 2  j 21 Ω
(C) Z 0  j 21 Ω, Z 1  j 7 Ω and Z 2  j 7 Ω
(D) Z 0  0 Ω, Z 1  j 7 Ω and Z 2  j 7 Ω
56.
Two 60 Hz generating units operate in parallel within the same power plant and have the
following ratings:
Unit 1: 500 MVA, 0.85 power factor, 20 kV, 3600 rpm, H1 = 4.8 MJ/MVA
Unit 2: 1333 MVA, 0.9 power factor, 22 kV, 1800 rpm, H2 = 3.27 MJ/MVA
The equivalent H constant for the two units on a 100 MVA base is
(A) 8.07 MJ/MVA
(B) 67.59 MJ/MVA
(C) 6759 MJ/MVA
(D) 807 MJ/MVA
57.
A 3 – phase synchronous generator, with negligible armature resistance, operates at a lagging
power factor and delivers constant power to an infinite bus. If its excitation is increased, then
(δ = power angle and cos  = power factor)
(A) δ decrease and cos  tends to become unity
(B) δ decrease and cos  tends to become more lagging
(C) δ increase and cos  tends to become unity
(D) δ increase and cos  tends to become more lagging

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 10 of 15

58.
For the same output load current and firing angle
(A) 3 phase half controlled converter has better displacement factor but poorer distortion
factor compared to three phase fully controlled converter
(B) 3 phase half controlled converter has better displacement factor and distortion factor
compared to three phase fully controlled converter
(C) 3 phase half controlled converter has better distortion factor but poorer displacement
factor compared to three phase fully controlled converter
(D) 3 phase half controlled converter has poorer displacement factor and distortion factor
compared to three phase fully controlled converter
59.
For a JK flip flop, Qn is the at a time step tn. Which of the following Boolean expression
represents Qn 1 ?
(A) J n Q n  K n Qn (B) J n Qn  K n Q n
(C) J n Qn  K n Q n (D) J nQn  K n Q n
60.
Which one of the following is the transfer function of the PI controller?
K s  K2 K s  K 2 s  K3
(A) G s   1 (B) G s   1
K3 K4s
K s  K2 Ks
(C) G s   1 (D) G s   1
K3s K 2s
61.

Using superposition theorem, the current Is in


the circuit shown in the figure is
(A) 1.09 A
(B) 2.18 A
(C) 5.45 A
(D) 6.54 A
62.
As soon as a new value of variable is found by iteration, it is used immediately in the following
equations, this method is called
(A) Gauss-Jordan method (B) Gauss-Seidel method
(C) Jacobi’s method (D) Relaxations method
63.
The relation between electric polarization and susceptibility indicates that electric polarization is
(A) independent of susceptibility
(B) inversely proportional to susceptibility
(C) proportional to square root of susceptibility
(D) proportional to susceptibility
64.
The circuit in the figure shows a balanced 3 – phase system having a balanced self inductive
reactance of XL per phase, a mutual reactance of Xm between pairs of phases. The line currents
are Ia, Ib and Ic and they may be unbalanced. The series voltage drop relations would be
Vaa  I a X L  I b X m  I c X m , Vbb  I a X m  I b X L  I c X m and Vcc  I a X m  I b X m  I c X L

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 11 of 15

The positive- , negative- and zero- sequence reactances X1,


X2 and X0 respectively
(A)  X L  X m ,  X L  X m  and  X L  2 X m 
(B)  X L  X m ,  X L  2 X m  and  X L  2 X m 
(C)  X L  2 X m ,  X L  X m  and  X L  2 X m 
(D)  X L  2 X m ,  X L  2 X m  and  X L  X m 
65.
Under the conditions of maximum load on a cylindrical rotor synchronous motor, the reactive
power input to the motor is
3Vt E f 3E 2f
(A)  (B) 
Xs Xs
3Vt 2 3Vt 2
(C)  (D)
Xs Xs
66.
The difference between the indicated value and the true value of a quantity is
(A) gross error (B) absolute error
(C) dynamic error (D) relative error
67.
A 3 – phase, 20 kW, 400 V, 1470 rpm, 50 Hz Squirrel cage induction motor develops a torque of
100 Nm at a speed of 1400 rpm. If the motor is connected to a 30 Hz supply. For keeping the
same air gap flux, the supply voltage and the speed for the same load torque would respectively
be
(A) 240 V, 840 rpm (B) 240 V, 800 rpm
(C) 240 V, 780 rpm (D) 240 V, 750 rpm
68.
A Buck converter operates from a dc voltage source of Vdc. From oscilloscope traces, it is found
that inductor current rises for time tr, falls to zero over time tf and remains zero for time to. Then
the average output voltage Vo can be expressed as
t  t   t 
(A) Vdc  r o  (B) Vdc  r 
 tr   t r  t f 
t  t  t 
(C) Vdc  r  (D) Vdc  r o 
 t f   tr 
69.
In order to build MOD – 12 counter, the minimum number of flip flops needed is equal to
(A) 12 (B) 4 (C) 3 (D) 1
70.
A system is described by the following differential equation:
dy t  dx t 
 2 y t    xt  , x0   y 0  0 where x t  and y t  are the input and output
dt dt
variables respectively. The transfer function of the inverse system is
s 1 s2 s 1 s 1
(A) (B) (C) (D)
s2 s 1 s2 s2

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 12 of 15

71.
If vt   60e 2t cos4t  V, then the current i t  shown in
the circuit is
(A) 2.4  j 4.8 A
(B)  2.4  j 4.8 A
(C)  12  j10 A
(D) 12  j10  A
72.
1
Z – transform of   is
 n !
1 1

(A) eZ (B) e Z (C) e Z (D) eZ
73.
Which of the following reactance will be used to determine the interrupting capacity of circuit
breakers (except those which open instantaneously)?
(A) Sub-transient reactance for synchronous generator and transient reactance for
synchronous motor.
(B) Transient reactance for synchronous generator and sub-transient reactance for
synchronous motor.
(C) Transient reactance for both synchronous generator and synchronous motor.
(D) Sub-transient reactance for both synchronous generator and synchronous motor.
74.
If Fourier transform of function x t  is X    u   1  u   1 , then x t  is
1 1
(A) cos (B) sin  (C) cos  (D) sin 
 
75.
A 69 kV circuit breaker having a voltage range factor K = 1.21 and a continuous current rating of
1200 A has a rated short circuit current of 19,000 A at the maximum rated voltage of 72.5 kV.
The maximum symmetrical interrupting capability of the breaker is
(A) 1200 A (B) 19,000 A (C) 22,990 A (D) 22,990  2 A
76.
An over current relay is said to over reach when it operates at a current
(A) Higher than its setting (B) Equal to its setting
(C) Lower than its setting (D) 2/3 rd of its setting
77.
A 4 pole, 3 – phase, 50 Hz synchronous motor and 8 pole, 3 – phase, 50 Hz Slip Ring Induction
Motor are coupled to each other mechanically and operate on the same 3 – phase, 50 Hz supply
system. The slip rings of the induction machine are left open circuited. The frequency of the
voltage across any two slip rings would be
1. 50 Hz 2. 100 Hz 3. 150 Hz 4. 25 Hz
Options:
(A) 2, 3 (B) 2, 4 (D) 1, 3 (D) 1, 4
78.
The six stepped load phase voltage of a 3- square wave inverter with a dc link voltage of 100 V
will have the following RMS magnitudes of 1st, 3rd and 5th harmonic voltages:

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 13 of 15

(A) 10 V, 30 V and 50 V respectively (B) 100V, 33.3V and 20 V respectively


(C) 39V, 0V and 7.8 V respectively (D) 45V, 0V and 9V respectively
79.
Which one of the following register of 8085 microprocessor is not a part of programming model?
(A) Instruction register (B) Memory address register
(C) Status register (D) Temporary data register
80.
The system matrix of a continuous time system is described in the state variable form is,
x 0 0 
A  0 y  1  . The system is stable for all values of x and y satisfying,
 
0 1  2
1 1 1 1
(A) x , y (B) x , y0 (C) x  0, y  2 (D) x  0, y 
2 2 2 2

Section B: General Awareness and Numerical Ability

81.
Find the missing number in the given series:
2, 10, 30, 68, 130, ??
(A) 231 (B) 190 (C) 214 (D) 222
82.
The book “Exam Warriors” was written by
(A) M. Venkaiah Naidu (B) K. Chandra Sekhar Rao
(C) Dr. APJ Abdul Kalam (D) Narendra Modi
83.
Synonym for FOOLPROOF is
(A) protected against fools (B) that cannot go wrong
(C) useful (D) wise
84.
Who constructed the Bheemeswara Temple located at vemulwada?
(A) Arikesari – I (B) Arikesari – II
(C) Baddega (D) Venga Raja
85.
e – mail was developed by
(A) Raymond Samuel Tomlinson (B) Grace Murry Hopper
(C) Charles Babbage (D) Tim Burners Lee
86.
Rahim travelled straight from point E to F at a distance of 5 km. From F he turned left and
travelled 6 km and reached point G, there he took a left turn and travelled 5 km to reach point H.
He took another left turn and travelled 2 km and reached point I. How far is he from the starting
point?
(A) 3 km (B) 4 km (C) 5 km (D) 7 km

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 14 of 15

87.
Ivanka Trump visited Hyderabad during November 2017 to attend in
(A) Global Women Empowerment Summit – 2017
(B) Global Economic Summit – 2017
(C) Global Entrepreneurship Summit – 2017
(D) Asian Entrepreneurship Summit – 2017
88.
Having secured the highest marks in the class, _________.
(A) the college had offered him a scholarship
(B) he was offered a scholarship by the college
(C) a scholarship was offered by the college
(D) a college scholarship has been offered to him
89.
In the History of Telangana, during Salar Jung I period, the word “NIZAMATH” is associated
with
(A) District collector (B) Judicial officer
(C) Police force (D) Legal Secretary
90.
When was the first smart phone launched?
(A) 2006 (B) 2002 (C) 1992 (D) 1986
91.
A is B’s sister. C is B’s mother, D is C’s father, E is D’s mother, then how A is related to D?
(A) Grandfather (B) Grand daughter (C) Daughter (D) Niece
92.
The outside rearview mirror of modern vehicles is marked with warning “objects in the mirror
are closer than they appear”. Such mirrors are
(A) plane mirrors
(B) concave mirrors with very large focal lengths
(C) concave mirrors with very small focal lengths
(D) convex mirrors
93.
“His parent died when he was young”. “I think that’s why he has ______ problems”.
(A) too many (B) so many
(C) any more (D) much more
94.
K. Chandrashekar Rao, the leader of Telangana Rashtra Samiti, announced an indefinite fast to
begin on 29th November 2009 at
A) Rangareddy B) Medak C) Hyderabad D) Siddipet
95.
Which IT company’s nick name is “The Big Blue”?
(A) Google (B) Microsoft (C) Infosys (D) IBM
96.
Suresh is 7 ranks ahead of Ashok in the class of 39 students. If Ashok's rank is 17th from the
last, what is Suresh's rank from the start?
(A) 16th (B) 23rd (C) 24th (D) 15th

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE
Page 15 of 15

97.
The mobile app BHIM (Bharat Interface for Money) is based on
(A) Central payment interface (B) Local payment interface
(C) Unified payment interface (D) World payment interface
98.
Select the antonym from the following for the underlined word in the given sentence.
Sentence: “The speaker was unable to pacify the crowd”.
(A) excite (B) antagonize (C) threaten (D) challenge
99.
Which of the following dance in Telangana culture is also known as Sugalis or Banjaras?
(A) Lambadi dance (B) Kuchipudi dance
(C) Gusadi dance (D) Tribal Dhimsa dance
100.
The present chairman of the Rajya Sabha is
(A) P.J.Kurien (B) Smt. Sumitra Mahajan
(C) Hamid Ansari (D) M.Venkaiah Naidu

Life and Time are the world’s best teachers. Life teaches us to make good
use of time and time teaches us the value of life
- APJ Abdul Kalam

http://electrical-mentor.blogspot.in/ (March 01, 2018) Copy rights reserved © 2018


GTD - 05: Prepared by BNSS Shankar, M.Tech (IITK), MIE

You might also like