0% found this document useful (0 votes)
99 views19 pages

RZ A Installation Instruction 2

This document provides installation and programming instructions for a keypad digital deadbolt. It includes an overview of the installation process in 5 steps, descriptions of the parts, and instructions for setup and programming the lock.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
99 views19 pages

RZ A Installation Instruction 2

This document provides installation and programming instructions for a keypad digital deadbolt. It includes an overview of the installation process in 5 steps, descriptions of the parts, and instructions for setup and programming the lock.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

Keypad Digital Deadbolt

Installation Guide / Programming Instructions

Thank you for purchasing our products. Please review this manual thoroughly before operating your device.
All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
Installation Overview Programming Instructions

P3 STEP 1: Prepare the door and check dimensions P9 At a Glance P 15 Factory Default Settings

P4 STEP 2: Install the latch and strike P10 How to Use P16 Troubleshooting

P6 STEP 3: Install exterior assembly P 11 'HͤQLWLRQV P17 Information & Safety Warnings

P7 STEP 4: Install interior assembly P 12 Code Format

P8 STEP 5: Detect left/right hand door installation P 13 Quick Set Up

TOOL REQUIRED: IMPORTANT:


Do not use an electric Do not load batteries until lock is
screwdriver during installation. completely installed.
Battery
INSTALLATION OVERVIEW Cover (G)
Interior
Assembly (F)

Mounting
plate (E)

Exterior Assembly
(D)

Mounting
plate Screws (J)

Latch (A)

Interior Assembly
Screws (K)

Strike (C)

Reinforcement
Backup key (M) Latch Screws plate (C-1)
(I)

Strike Screws
(H)
1
Parts List

A Latch x1 B Drive-In Collar (Optional) C Strike x1 D Exterior Assembly x1

C-1 Reinforcement
Plate x1
(optional)

E Mounting Plate x1 F Interior Assembly x1 G Battery Cover x1 H Strike Screws x2

I Latch Screws x2

J Mounting plate K Interior Assembly L Reset Tool x1 M Backup Key x2


Screws x2 Screws x3

If any parts are missing or damaged, please contact Customer Support.


2
STEP

1 Prepare the door and check dimensions

A B 2-3/8" or 2-3/4"
(60 or 70mm)
Measure to Measure to confirm
confirm that the that the backset is
hole in the door is either 2-3/8" or
2-1/8" (54mm). 2-3/4" (60 or 70mm)

Measure to confirm
that the hole in the
door edge is 1"
(25mm).

C D
Measure to confirm Make sure the hole in
that the door is 1-3/8" 1-3/8" to 2" door frame is drilled a
to 2" (35 mm or (35mm or 50mm) minimum of 1"
50mm) thick. (25mm) deep.
1"
25mm

3
STEP

2 Install the latch and strike


Determine backset YES
A and adjust the latch No adjustment is required.
Proceed to next step.

NO
Slotted hole is
NOT centered.
Hold the latch in front of the door hole, Rotate and pull the
with the latch face flush against the 2-
latch as shown to 2-3
door edge. Is the slotted hole centered (60 3/8" pu (70 /4"
extend latch. mm ll mm
in the door hole? ) )

up

B Latch Screws (I)


chiseled
Install the latch

Drive-In Collar
(B)
not chiseled
4
Use a screwdriver to test if
C deadbolt works smoothly.

IMPORTANT:
D Install strike on the door frame.
Make sure the hole in door frame is
drilled a minimum of 1" (25mm)
deep.

(Optional)

5
STEP

3 Install exterior assembly

IMPORTANT:
Unlocked Locked
Before installation, make sure the latch is
fully retracted (in the unlocked position)

Keep parallel to
door edge.

Torque
blade

Mounting plate Screws(J)

With the latch fully retracted (in the unlocked Secure the mounting plate with the
A position), route the cable below the latch, and
B supplied screws. Do not overtighten
insert the torque blade through the slot in the screws.
latch.
6
STEP

4 Install interior assembly

Insert the cable


A B connector to the
Push the battery cover out in socket. Push the
the direction as illustrated. connector in firmly
until it is completely
IMPORTANT: attached.

Do not load batteries until lock is


completely installed.

Keep the thumb turn in vertical position and install


C Attach Interior
the interior assembly. D Assembly to
Mounting Plate and
tighten 3 Screws.
Horizontal

Unlocked Interior Assembly


Screws (K)

7
STEP

5 Detect left/right hand door installation


Reset the lock to teach the lock the orientation of the door.
IMPORTANT:
This step is required and crucial for the lock
to operate properly.

While the door is OPEN and Press and hold the Reset button on Load the 4th battery and keep holding
A UNLOCKED, load 3 AA batteries
B the interior assembly by using the
C the reset button for 3 seconds, until
into the battery compartment. reset tool. you hear the sound of "beep". The
Note: latch bolt will extend to learn the
orientation of the door automatically.
For long last, please use all new,
non-rechargeable Alkaline
batteries only.

Reset button

Unlocked

8
PROGRAMMING INSTRUCTIONS

At a Glance

Exterior Assembly Interior Assembly

Multi-Function Battery Cover


Button(MFB)
Keypad

Reset Button

Keyhole

Thumb Turn

9
How to Use

UNLOCK the door from outside UNLOCK the door from inside
Master code + or User code + Rotate the thumb turn to
Unlock position.

LOCK the door from outside LOCK the door from inside
Auto Lock Mode Manual Mode Auto Lock Mode Manual Mode
In Auto Lock mode, the bolt Press any key on keypad for In Auto Lock mode, the Rotate the thumb turn to Lock Position.
will extend out automatically in 2 seconds. device will be locked
30 seconds after unlocking. automatically.

or

10
Definitions Programming Basic

• Master Code • Silent Mode


Required for programming and feature settings. Master code can be The beep sounds when pressing keypad can be muted. But you will
used to unlock the door under vacation mode. The default master still hear low battery and system alerts.
code needs to be changed before programming.
• Vacation Mode
Property owner & manager should keep this information confidential.
This is a security feature for you when you are leaving your home for
• Auto Lock vacation or long trip. Enabling vacation mode will restrict all user
Automatically locks the deadbolt 30 seconds after unlocking. This codes until master code is entered on keypad. If the lock would be
feature is off by default. You can customize the Auto Lock time delay unlocked by the thumb turn from the inside, the lock will sound an
between 10 and 99 seconds. alarm.

• Key Unlock • One Time User Code


Key Unlock is always available when the batteries are completely This code only can be used once and will be automatically deleted
dead or valid User Codes are forgotten. after used.

• Low Battery Indicator • Unlock with Fake code


If you hear 10 beeps along with 10 red light flashing after pressing User can prevent pin code exposure from strangers by entering
any key to lock or unlock the door, that’s an alert for replacing random digits before or after pin code.
batteries. Please replace with 4 brand new AA alkaline batteries and
do not mix used and new batteries. All settings are stored in the lock
while the batteries are removed and replaced.

• Wrong Entry Limit


After 10 unsuccessful attempts at entering a invalid PIN code, the
unit will shut down for 3 minutes.

11
Code Format Programming Basic

1. Master Code(4 to 10 digits): The default Master Code is 12345678. It is required that you change it to a code of your own before
programming.

2. User Code (4 to 10 digits): A total of 20 User Codes (including one temporary one-time User Code) can be programmed and stored.

3. Both Master Code and User Code don’t support the following combination of numbers.

Forward number sequence

Backward number sequence

Repeat number sequence

Contain existing code sequence

12
The default Master Code is 12345678 .
Quick Set Up IMPORTANT: It is required that you change it to a code of
your own before programming.

Change + Master Code + Press New Master Code + New Master Code +
Master
Code
Succeed
Wait for long green lights Wait for green light flash Wait for green light flash
Green light flash

Add + Master Code + Press New User Code + New User Code +
User
Code Succeed
Wait for long green lights Wait for green light flash Wait for green light flash
Green light flash

+ Master Code + Press Unwanted User Code +


Delete
User
Code Succeed
Wait for long green lights Wait for green light flash
Green light flash

Press Silent Mode Disabled


+ Master Code +
Green light flash
Silent
Mode
Wait for long green lights Silent Mode Enabled
Wait for green light flash
Green light flash

13
+ Auto Lock Enabled
+ Master Code + Press Green light flash
Auto
Lock Auto Lock Disabled
+
Wait for long green lights Wait for green light flash Green light flash

+ Master Code + Press Enter New Duration Time +


Set Auto (10-99s)
Lock Time
Succeed
Wait for long green lights Wait for green light flash Green light flash

Add + Master Code + Press New User Code + New User Code +
One-Time
Code Succeed
Wait for long green lights Wait for green light flash Wait for green light flash
Green light flash

Enable + Master Code + Press Press


Vacation
mode Vacation Mode Enabled
Wait for long green lights Wait for green light flash
Green light flash

Disable Master Code +


Vacation
mode Vacation Mode Disabled
The door was opened

Notes:
1. Beeps only sound when the Silent Mode is disabled.
2. If the indicators flash red light, it means your setting failed and it will require to re-enter master mode if you would like to continue your programming.
14
Factory Default Settings

How to Reset?
Reset button

The resetting will delete all User Codes stored


IMPORTANT: in the lock.

Step 1. Keep the door open and unlocked.

Step 2. Press and hold the Reset button, at the same time take out one
battery and then place it back.

Step 3. Keep holding the Reset button for 3 seconds, until you hear the
sound of "beep" and the latch will extend automatically.

Settings Factory Defaut

Master Code 12345678

Auto Lock Disabled

Silent Mode Disabled

Wrong Code Entry Limit 10 times

Shutdown Time 3 mins

Vacation Mode Disabled

15
Troubleshooting

Why does not the latch extend but the motor is rotating Why does my lock only work properly when the backup key
when resetting my lock? is in? Why am I unable to pull the key out in the unlocked
Improper installation may have caused the issue. Please follow the position?
steps to review: You may need to re-install the whole lock.
1. Please make sure the latch and strike are aligned. Please make sure when you start to install, the lock is in unlocked
2. Please slightly loosen the mounting screws on the external status;
assembly keypad and the latch bolt if the screws are over-tight- Please make sure the thumb turn is vertical.
ened. Please do not put the backup key in the lock.
3. Please open your door and reset the lock.
What does 5 short and fast beeps mean while program-
Why does not the latch extend and the motor isn't rotating ming?
when resetting my lock?
It alerts you either time-out or wrong entry.
The deadbolt latch should be retracted(unlocked) through all your
Please be sure to complete each setting step within 5 seconds.
installation process.
Please change the default master code in the first time programming.
The thumb turn should be vertical in your installation steps 4C and 5A.
Please be sure the user code is with correct format and with 4 to 10
Please open your door and reset the lock. digits.

When I attempt to lock/unlock my deadbolt, why does the What if I forget my Master Codes?
latch go in and out for a few times? If you forget your Master code, resetting your lock, then the original
It happens when the latch and strike are misaligned. master code (12345678) works, and all previous user codes were
Please make sure the bolt hole on the door frame is at least 1 inch erased.
deep, so that the bolt can be fully extended.
Please check if the door can be closed properly, the deadbolt should
not impact the strike or door frame on the door frame side, it should go
directly into the hole properly.

16
Information & Safety Warnings

• Protect your User Codes and Master Code. • Care should be taken to ensure a long-lasting finish. When cleaning is
required use a soft, damp cloth. Using lacquer thinner, caustic soaps,
• Restrict access to your lock’s interior assembly and routinely check your abrasive cleaners or polishes could damage the coating and result in
settings to ensure they have not been altered without your knowledge. tarnishing.
• Do not use an electric screwdriver during installation. • The lock is water resistant. It can withstand water splashes; however, do
• This manufacturer advises that no lock can provide complete security by not let water and liquids get into the lock.
itself. • Avoid exposure to direct sunlight. Long-term exposure to direct sunlight
• This lock may be defeated by forcible or technical means, or evaded by may damage the lock.
entry elsewhere on the property.

• No lock can substitute for caution, awareness of your environment, and


common sense.

17

You might also like