DL105 I/O Specifications

F1-130DR Output point wiring

Wiring diagram
and specifications
Power requirements
Voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . .94-240 VAC (30 VA)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100-240 VDC (30 W)
DC input specifications
Number of input points . . . . . . . . . . . . . . . . . . . . . . .10 (sink/source)
Number of commons . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 (isolated)
Input voltage range . . . . . . . . . . . . . . . . . . . . .(X0–X3):10-26.4 VDC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(X4-X11):10-26.4 VDC or
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21.6–26.4 VAC
Input impedance . . . . . . . . . . . . . . . . . . . . . . .2.8 K⏲ @ 12-24 VDC
ON current/voltage level . . . . . . . . . . . . . . . . . . . . .> 3 mA / > 9 VDC
OFF current/voltage level . . . . . . . . . . . . . . . . . .< 0.5 mA / < 2 VDC
OFF to ON response . . . . . . . . . . . . . . . . . . . . . . . . . . .X0-X3: 50 µs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .X4-X11: 2-8 ms
ON to OFF response . . . . . . . . . . . . . . . . . . . . . . . . . . .X0-X3: 50 µs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .X4-X11: 2-8 ms
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .None
Relay output specifications
Number of output points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Input point wiring
Number of commons . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 (isolated)
Output circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Relay
Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-250 VAC Equivalent circuit
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-30 VDC high-speed inputs (X0-X3)
Maximum voltage . . . . . . . . . . . . . . . . . . . . . . . .265 VAC, 150 VDC
Maximum current . . . . . . . . . . . . . . . . . . . . .7 A/point (see derating)
Maximum inrush current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 A
Minimum load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Minimum OFF resistance . . . . . . . . . . . . . . . . .100 M⏲ @ 500 VDC
OFF to ON response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ms
ON to OFF response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ms
Fuses . . . . . . . . . . . . . . . . . . . . . . . . .None (external recommended)
Auxiliary 24 VDC Output
Voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21.6 - 26.4 VDC
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 mA max., isolated Equivalent circuit
Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .less than 200 mV p - p standard inputs (X4-X11)
Typical Relay Life (Operations)
at Room Temperature
Voltage and Type Load Current
of Load 50 mA 5A 7A
24 VDC Resistive 10M 600K 300K
24 VDC Solenoid — 150K 75K
110 VAC Resistive — 600K 300K
110 VAC Solenoid — 500K 200K
220 VAC Resistive — 300K 150K
Equivalent output circuit
220 VAC Solenoid — 250K 100K
Derating chart for DC inputs Derating chart for relay outputs
Features and Specifications
The DL105 micro PLCs contain the CPU, AC-powered units
power supply and I/O all in the same DL105 CPU Specifications
F1-130AA
housing. If you examine the CPU 10 AC inputs, 8 AC outputs, 1.7 A/point
Specifications table, you’ll see that we
F1-130AD System capacity
included many features found in our 10 AC inputs, 8 DC outputs, 1.0 A/point, two outputs can be
modular CPUs. used as 7 kHz pulse output, 0.5 A/point Total memory available (words) . . . . . . . . . . . . . . . . . . . . 2.4K
Ladder memory (words) . . . . . . . . . . . . . . . . . 2,048 EEPROM
F1-130AR V-memory (words) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
10 AC inputs, 8 relay outputs, 7 A/point
Review the specs User V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
F1-130DA Non-volatile user V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Make sure these features can satisfy the 10 DC inputs, 4 inputs are filtered inputs, can also be config- Battery backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
requirements of your application. Since ured as a single 5 kHz high-speed counter, interrupt input, or Total I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
pulse catch input Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
these units are completely self-contained, 8 AC outputs, 1.7 A/point Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
you cannot expand the system or replace I/O expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
F1-130DD
the CPU as you would in a modular 10 DC inputs, 4 points are filtered inputs, can also be config- Performance
system. ured as a single 5 kHz high-speed counter, interrupt input, or Contact execution (Boolean) . . . . . . . . . . . . . . . . . . . . . 3.3 µs
pulse catch input Typical scan (1K Boolean)1 . . . . . . . . . . . . . . . . . . . . . . 5-6 ms
8 DC outputs, 1.0 A/point, 2 outputs can be used as 7 kHz
System capacity pulse output, 0.5 A/point Instructions and diagnostics
System capacity is the ability to accommo- RLL ladder style. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
F1-130DR RLLPLUS/flowchart style (Stages) . . . . . . . . . . . . . . . . . . Yes/256
date a variety of applications. For ladder 10 DC inputs, 4 inputs are filtered inputs, can also be config-
ured as a single 5 kHz high-speed counter, interrupt input, or Run-time editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
memory, most Boolean instructions require pulse catch input Supports Overrides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
one word. Some other instructions, such 8 relay outputs, 7 A/point Variable/fixed scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable
as timers, counters, etc., require two or Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
DC-powered units Control relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
more words. Our V-memory words are Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
useful for data storage, etc. F1-130DD-D Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
10 DC inputs, 4 inputs can be used as 5 kHz high-speed Immediate I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Performance counter, interrupt inputs, or pulse catch inputs Subroutines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
8 DC outputs, 1.0 A/point, two outputs can be used as 7 kHz For/next loops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
The performance is simply the scan time, pulse output, 0.5 A/point. Timed interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
which is the amount of time required to Integer math. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
F1-130DR-D
10 DC inputs, 4 inputs can be used as 5 kHz high-speed Floating-point math . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
read the inputs, solve the RLL program PID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
counter, interrupt inputs, or pulse catch inputs
and update the outputs. Drum sequencers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
8 relay outputs, 7 A/point
Bit of word . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
Instructions and diagnostics ASCII print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
Programming Real-time clock/calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . No
Make sure the unit offers the instructions Internal diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Handheld programmer.....D2-HPP. . . . . . . . . . . . . . . . . <--->
you need. DirectSOFT Programming for Windows Password security . . . . . . . . . . . . . . . . . . . . . . . . . . Multi-level
PC-DSOFT5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<---> System and user error log . . . . . . . . . . . . . . . . . . . . . . . . . . No
Communications PC-DS100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <---> Communications
PC-R50-U (upgrade) . . . . . . . . . . . . . . . . . . . . . . . . . . . <---> Built-in ports . . . . . . . . . . . . . . . . . . . . . . . . . . one, RS-232-C
All DL105 units offer one RS-232 port, K-sequence (proprietary protocol) . . . . . . . . . . . . . . . . . . . Yes
capable of 9,600 baud. DirectNET™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
MODBUS master/slave . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
Specialty features ASCII out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No
Baud rate (fixed) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9,600 baud
With the DC input and/or DC output
Specialty features
versions, we also offer several high-speed Filtered inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes2
I/O features. Interrupt input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes2
High-speed counter . . . . . . . . . . . . . . . . . . . . . . . . Yes, 5 kHz2
Pulse output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes, 7 kHz2
Pulse catch input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes2

1- Our 1K program includes contacts, coils, and scan

Note: Either high-speed input or pulse output overhead. If you compare our products to others,
can be used, but not in the same configuration. make sure you include their scan overhead.
2- Input features are only available on units with DC
inputs. Output features are only available on units
with DC outputs.
DL105 Hardware Features
Output terminal
CPU status indicators block (removable)

RUN . . . . . . .ON . . . . . . . . . . . . . . . . . . CPU is in RUN mode Terminal covers

. . . . . . . . . . .OFF . . . . . . . . . . . . CPU is in PROGRAM mode
PWR . . . . . . .ON. . . . . . . . . . . . . . . . . . . . . . CPU power good
. . . . . . . . . . .OFF . . . . . . . . . . . . . . . . . . . . CPU power failure
CPU . . . . . . .ON . . . . . . . . . . . . . . . CPU internal diagnostics
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . has detected an error
. . . . . . . . . . .OFF . . . . . . . . . . . . . . . . . . . . . . . . . . CPU is OK Output LEDs

6-pin female
Mode control connector

The DL105 units do not have mode

switches like many of our modular CPUs.
You can set the unit (using special
V-memory locations) so that it will power
up in RUN mode.

Communications port
Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . K-sequence slave
Devices . . . . . . . . . . . . . . . . . . . . . . . . . Can connect with HPP, Auxiliary 24VDC supply Input terminal block
Input LEDs CPU status LEDs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DirectSOFT, DV-1000, (AC powered units only) (removable)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-More Panels
Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . 6P6C RJ12 connector
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-232-C, 9,600 baud,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Odd parity,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixed station address (1),
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 data bits (one start,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . one stop bit),
. . . . . . . . . . . . . . . . . . . . . . . . Asynchronous, half-duplex, DTE

RJ12 Connector Port 1 Pinout

Pin. . . . . . . . . . . . . . . . . . . . . . . . Signal
1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-232 Data in
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-232 Data out
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V
6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V

Fixed EEPROM memory

The DL105 units offer built-in EEPROM
memory.

NOTE: Terminals accept 16-24 AWG. For 16 AWG, use

type TFFN or Type MTW. Other types of 16 AWG may
be acceptable, but it really depends on the thickness
of the wire insulation.
Dimensions and Installation
It is important to understand the installa-
tion requirements for your DL105 system.
This will help ensure that the DL105 prod- Installation
ucts operate within their environmental
and electrical limits.

Plan for safety

This catalog should never be used as a
replacement for the user manual. The user
manual, D1-USER-M, contains important
safety information that must be followed. Temperature probe
The system installation should comply with 2"
all appropriate electrical codes and stan- 50mm
dards. min

Unit dimensions and

mounting orientation Power source
Use the following diagrams to make sure
2"
the DL105 system can be installed in your 50mm
application. DL105 units must be mounted min
horizontally to ensure proper airflow for
cooling purposes. It is important to check 2"
Panel ground terminal
these dimensions against the conditions 50mm
required for your application. For min
example, we recommend that you leave 2" Bus b
ar
depth for ease of access and cable clear- Ground braid
Panel
ance; however, your distance may be copper lugs Earth
greater or less. Also, check the installation ground
guidelines for the recommended cabinet
clearances. Panel or single
Point ground
Star washers

Note: There is a minimum of 2" (50mm) clearance required between the panel door or any devices mounted in
the panel door and the nearest DL105 component.

Dimensions and mounting

Environmental Specifications
Storage -4ºF to 158ºF (-20ºC to 70ºC) 3.48
Temperature Units: inches(mm)
(88.3)
Ambient 5.12
Operating 32ºF to 131ºF (0º to 55ºC) (129.9)
Temperature
Ambient 30% to 95% relative humidity (non-
Humidity condensing)

Vibration MIL STD 810C, Method 514.2

Resistance 3.16
Shock (80.3)
MIL STD810, Method 516.2
Resistance
Noise NEMA(ICS3-304)
Immunity 3.63
(92.1)
Atmosphere No corrosive gases
Power Supply and Type of I/O
Power supply options Power Supply Options
This product family offers units that
Specification AC Powered Units 24 VDC Powered Units
operate on 110/220 VAC and 12/24
VDC. Choosing the power supply is prob- F1-130AA, F1-130AR
ably the most important consideration F1-130AD, F1-130DA
F1-130DD-D
Part Numbers F1-130DD, F1-130DR
when specifying a DL105 system, since F1-DVNET-AR, F1-DEVNET-DD
F1-130DR-D
not all I/O combinations are offered with F1-DVNET-DR
each power supply option. The table to
the right provides the I/O choices and Voltage Withstand (dielectric) one minute @ 1,500 VAC between primary, secondary and field
ground
power supply specifications for each type
unit. Insulation Resistance > 10 M⏲ @ 500 VDC

85-132 VAC (110 nominal) 10-30 VDC

Choosing the I/O External Power Requirement 170-264 VAC (220 nominal)
100-264 VDC (125 nominal)
(12 to 24 VDC)
with < 10 percent ripple
The DL105 product family offers several
Auxiliary 24 VDC Output 500 mA max. Not available
different combinations of I/O points.
Once you have chosen the power supply Maximum Inrush Current 12 A 8A
option, you need to choose the unit that Maximum Power 30 VA max. 1 A (approx. 10 W)
offers the type of I/O points needed in
your application. AC-powered units
Addresses automatically
Part No. I/O Mix
Fixed I/O assigned F1-130AA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Ac in
The DL105 uses automatic addressing, so . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AC out
All DL105 Micro PLCs have “fixed” I/O F1-130AD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 AC in
that is updated on every scan. This means for the vast majority of applications, there . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DC out
that all units have 10 inputs and is no setup required. We use octal F1-130AR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 AC in
addressing for many of our products, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 relay out
8 outputs, regardless of the actual type of F1-130DA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DC in
points on the units (DC in/Relay out, DC which means there are no 8s or 9s.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AC out
in/DC out, etc.) The DL105 micro PLC is The first eight input points use addresses F1-130DD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DC in
non-expandable, so you cannot add I/O X0-X7, and the last two input points use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DC out
X10 and X11. If you plan on using the F1-130DR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DC in
points. If you are concerned about future . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 relay out
system expansion, check our DL06 (36 high-speed counting features, there is
base I/O expandable to 100 total I/O), or some very minimal setup required in DC-powered units
the DL205 micro-modular product family. special V-memory locations.
Part No. I/O Mix
The DL205 also offers a wide array of F1-130DD-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DC in
features and flexible I/O arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DC out
F1-130DR-D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 DC in
with several different base sizes.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 relay out

AC supply Output addresses

Indicates group per

common

24 VDC auxiliary supply

(AC powered units only)
Input addresses