Technical Data Sheet

373;2725;3622;1507 1,2 373 silyl acrylate VValidationDate). 1

antifoulings

SeaQuantum Ultra

Product description
This is a one component state of the art chemically hydrolysing silyl acrylate antifouling coating. It provides
excellent fouling protection and incomparable hull performance. This is achieved through highly predictable and
stable self polishing characteristics reducing hull deterioration, friction and speed loss. To be used as finish coat
in immersed environments only. Suitable on approved primers and tie coats on aluminum and carbon steel
substrates. It can be applied at sub zero surface temperatures.

Typical use
Marine:
Recommended for under water hull in newbuilding and dry docking. Specially designed as a premium solution
for vessels with low activity and slow steaming. Recommended solution for areas with high fouling exposure,
such as sea chest, to minimise risk of invasive species. This product provides optimum hull protection in fouling
intensive waters or in trades with long lay-ups. The product is designed for long service periods and can be used
up to 90 months as a part of a complete coating system.

Protective:
Recommended for offshore constructions and immersed areas on static installations.

Typical trade
Designed for global and especially coastal trade. Recommended for exposure to both sea and fresh water during
newbuilding outfitting.
Antifouling.

Approvals and certificates

Compliant with IMO Antifouling System Convention AFS/CONF/26.
Additional certificates and approvals may be available on request.

Colors
dark red, light red

Product data
Property Test/Standard Description
Solids by volume ISO 3233 47 ± 2 %
Flash point ISO 3679 Method 1 77 °F (25 °C)
Specific gravity calculated 1,67 kg/l
VOC-USA / VOC Hong Kong EPA Method 24 3,92 lbs/gal
VOC-Solvent Emission Directive SED (1999/13/EC) 290 g/kg

The provided data is typical for factory produced products, subject to slight variation depending on color.

Recommended film thickness per coat

Date of issue: 4 August 2014 by Jotun Group Page: 1/4

This technical data sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
SeaQuantum Ultra

Film thickness and Dry film thickness Wet film thickness Theoretical
spreading rate spreading rate
mils (μm) mils (μm) ft²/gl (m²/l)

Minimum 3 mils (75 µm) 6 mils (160 µm) 253 ft²/gl (6,2 m²/l)
Maximum 6 mils (150 µm) 13 mils (320 µm) 126 ft²/gl (3,1 m²/l)

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Coated surfaces New tie coat or new antifouling: New tie coat or new antifouling:
Remove any contamination that Remove any contamination that
could interfere with the intercoat could interfere with the intercoat
adhesion. Exceeding maximum adhesion. Exceeding maximum
recoat intervals will require cleaning/ recoat intervals will require cleaning/
abrading and/or application of abrading and/or application of
additional coats, depending on additional coats, depending on
condition. condition.

Aged antifouling with leached layer: Aged antifouling with leached layer:
Removal by thorough fresh water Removal by thorough fresh water
washing at minimum nozzle pressure washing at minimum nozzle pressure
2900 psi (200 bar). 340 bar.

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Brush: May be used.Care must be taken to achieve the specified dry film thickness.
Roller: May be used.Care must be taken to achieve the specified dry film thickness.

Product mixing ratio (by volume)

Single pack

Stir/mix thoroughly with a power agitator before application.

Date of issue: 4 August 2014 by Jotun Group Page: 2/4

This technical data sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
SeaQuantum Ultra

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 7

Guiding data for airless spray

Nozzle tip (inch/1000): 17-31

Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time

Temperatures:
-10°C = 14°F / -5°C = 23°F / 0°C = 32°F / 5°C = 41°F / 10°C = 50°F / 15°C = 59°F / 23°C = 73°F / 35°C = 95°F / 40°C = 104°F / 100°C = 212°F

Substrate temperature -10 °C 0 °C 10 °C 23 °C 40 °C

Surface (touch) dry 5h 2h 45 min 30 min 30 min

Dried to over coat, minimum 24 h 16 h 9h 7h 6h
Dried/cured for immersion 36 h 24 h 10 h 9h 8h

Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and
within the DFT range of the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface.

Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.

Dried/cured for immersion: Minimum time before the coating can be permanently immersed in sea water.

Recommended type of primer

Anticorrosive primer system suitable for purpose. Recommended tie coat for the subsequent antifouling coat is
Safeguard Universal ES or Safeguard Plus.

Packaging (typical)
Volume Size of containers
(liters) (liters)

SeaQuantum Ultra 20 20

The volume stated is for factory made colors. Note that local variants in pack size and filled volumes can vary
due to local regulations.

20 l = 5.28 gal

Storage

Date of issue: 4 August 2014 by Jotun Group Page: 3/4

This technical data sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
SeaQuantum Ultra

The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 73°F (23 °C)

SeaQuantum Ultra 12 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Color variation
Products primarily meant for use as primers and antifoulings may have slight color variations from batch to
batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 4 August 2014 by Jotun Group Page: 4/4

This technical data sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com