Scribd
Upload
34 views2 pages

List of Connectors

Uploaded by

pronav2024
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
34 views2 pages

List of Connectors

Uploaded by

pronav2024
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

7.

3 Processor Unit (RPU-013)

2. Connector
Table 7.3.1(1/2) Connector on the TB board

TB board (03P9342) Connector No. Overview


Input of MIX (Video Sig.,) 60 MHz IF receiving signal from TR
J609 (Terminal) IF VIDEO sig.
unit
J651 (2P-VH) HV HV input from TX high voltage board (HV-9017)
J652 (10P-VH) PWR For connecting to the PWR board
MIX: (Video Sig.,) 60 MHz IF receiving signal inputted into the
J653 (Mini-Pin) SPU
SPU board (1.5 D co-axial cable)
J654 (80P) SPU For connecting to the SPU board
J601 - Program updating port of RS-232C type
PC
(male: 9pin D-SUB) - ON/OFF switching of Shuttle Ferry function
For connecting control unit (RCU-014) or RCU-015. Not
J602 (10P-XH) KEY
connectable to RCU-016 because it has no power switch.
Connector to be used when GC-10 is incorporated
J603 (6P-XH) GC-10
(HDG setting is made in [HDG] -> AD-10)
Used with FAR-2x37S and connected to PSU-007 by antenna
J604 (2P-WAGO) PSU ON/OFF signal and turns on and off the antenna motor power
supply line by relay
Heading data input from IEC61162-1 and 2 types. Supports a
range between 4800 bps to 38.4 kbps according to input data
J605 (3P-WAGO) HEADING
speed and automatically switched (HDG setting is made in
[HDG] -> Serial)
Connector to navigator system of IEC61162-1 and 2 types.
J606 (3P-WAGO) NAVIGATOR Supports a range between 4800 bps to 38.4 kbps according to
input data speed and automatically switched
For connecting to log serial signal of IEC61162-1 and 2 types.
J607 (3P-WAGO) LOG Supports a range between 4800 bps to 38.4 kbps according to
input data speed and automatically switched
AD Heading data input in AD format. Set the input interval to 25
J608 (WAGO-4P)
CONVERTER msec. (HDG setting is made in [HDG] -> AD-10)
J610 (12P-WAGO) SCANNER Connected to the scanner unit
J611 (5P-WAGO) AIS AIS connection connector of IEC61162-2 type
Four alarm output ports. Contact signal by MOS-FET contact.
J612 (12P-WAGO) EXT. ALARM Polarity of ALM 4 is opposite to that of other ports.
Sys Fail x1 and EXT ALM Ack should be inputted.
J613 (2P-WAGO) SCANNER Connected to the TR unit by TX HV
J614 (2P-WAGO) CARD I/F +12 VDC power supply output of CARD I/F (CU-200)
Power supply output for DVI I/F and RGB Buff boards (+12 V,
J615 (5P-WAGO) OPTION
+5 V and –12 V)
Connector for Video, HD, B.P and Trig input signals from
J616 (8P-NH) MASTER Radar
master radar
Connector for Video, HD, B.P and Trigger output signals from
J617 (8P-NH) SUB DISPLAY-1
this radar. Video signal is in FULL-LOG.

7-30
7.3 Processor Unit (RPU-013)

Table 7.3.1(2/2) Connector on the TB board

TB board (03P9342) connector No. Overview


Connector for Video, HD, B.P and Trigger output signals from
J618 (8P-NH) SUB DISPLAY-2
master radar. Video signal is in SEMI-LOG.
TTM output of IEC61162-1 type. For outputting TTM, set
J619 (3P-WAGO) ECDIS [Menu] -> 0 -> 6 -> 2:TTM OUTPUT to REL/TRUE and
[Menu] -> 0 -> 8 -> 5:Other to OFF
Connector to INS. Set [Menu] -> 0-> 8 -> 5 to Serial.
IEC61162-1 and 2 type. Supports the TX and RX data speed
between 4800 bps to 38.4 kbps according to input data speed
and automatically switched.
TRACK
J620 (5P-WAGO)
CONTROL
NOTE: In the program of SPU Ver.50.08 and after;
It is for RX port of GPS buoy sentence, and the sentence of
NAV, ECDIS cannot receive.
RX sentence: $GBBLV, &XXGLL, $TLL
J621 (6P-WAGO) SERIAL I/F Unassinged
J622 (2P-XH) KEY Connected in parallel like EXT ALM Ack of J612 (EXT. ALM)

7-31

You might also like