4 WEB Login

This machine supports WEB management. You can log in to

192.168.0.1 (default IP address) from any PC to get relevant FWG-GWCP
information. The steps are as follows: FTTH Home Gateway
1) Change the network segment of the PC to 192.168.0.X and User Guide
connect it to any network port of the machine with a network cable;

2) Enter http://192.168.0.1 in Chrome, press Enter to pop up the 1 Overview

login page, enter the username and password (admin/system), and
then enter the system management page. FWG-HGU824GWCP ONT is a three-in-one FTTH gateway for small
and medium-sized businesses, SOHO office and home users,
5 Matters Needing Attention
integrating xPON, WIFI, and CATV functions. This series of products
1) This device is an indoor structure, it can not be used in places
that are easily invaded by rainwater; it should have proper space in complies with the G.988 international standard and has good
the indoor box to facilitate heat dissipation; interoperability and operability, enabling interoperability with
2) The fiber input and the cable output must be reserved for a mainstream manufacturers' OLT devices.
certain length to avoid accidents caused by too short; the optical
2 Main Specifications
interface in the ONU is the SC/APC head. Do not misplace or the
end faces are inconsistent. ITEM UNIT SPEC

6 Accessories Working TX1310，RX1490

nm
wavelength CATV：1550
1). External power supply * 1: AC110～C255V→DC12V/1.5A
OP TX POWER dBm 1-4(EPON & GPON)
2). User Guide * 1
T RX Sensitivity dBm ≥ -28
3). The certificate of conformity has been affixed to this manual. I optic connector / SC/APC
Certification CA CATV optical
dBm -2～-18
L power range
Inspector:
CATV optical
dB ≥55
Date: reflection loss
2.4G:802.11 b/g/n 2.4GHz 300Mbps
WIFI /
O
5G:802.11 a/an/acGHz 867Mbps
T TYPE / HGU
 HE Indicator Status Description
POWER V/A AV110～255V→DC12V 1.5A
R ON The device is powered on normally.
Power
Size mm 196*135*31 OFF The device is not powered on.
Twinkling Received light, device not registered
Operating
℃ -5～45 The ONU is connected to the OLT and registered
temperature PON ON
successfully.
3 Instructions for Use OFF No optical received, device not registered
The network port is connected but no data is
1) Power Connection ON
transmitted.
This machine is supported by the power adapter. Firstly, connect LAN1-LAN4 Twinkling Network port has data transmission
the DC 12V output cable of the power adapter to the DC 12V port of The device is not powered on or the network port
OFF
the machine, and then plug the external regulated power supply is not connected to the terminal device.
into the 220V of the mains. The power indicator on the panel is on, ON WIFI works fine
indicating that the power supply is working normally. WIFI(2.4G/5G) Twinkling WIFI has data transmission
2 INTERFACES OFF WIFI work abnormally

INTERFACES Introduction ON Successfully connected to the Internet

ON/OFF Power switch button Internet
OFF Not connected to the Internet
Power Power input interface, DC 12V/1.5A
CATV and xPON fiber interfaces, using SC/APC ON The caller is ringing
Optical
fiber access
LAN1-LAN4 LAN service interface FXS1/FXS2 Twinkling Means the user is off the phone or on the phone

Reset Reset button

OFF free
WPS WPS switch
FXS1/2 VOIP Interface ON CATV optical signal is within the normal range
OPT
CATV CATV RF signal output OFF CATV optical signal is too low or faulty
2) Indicators Description ON RF output level is within the normal range
Indicator Status Description TV
OFF RF output level is not within the normal range
ON The device is powered on normally.
Power
OFF The device is not powered on.
Twinkling Received light, device not registered
The ONU is connected to the OLT and registered
PON ON
successfully.
OFF No optical received, device not registered
Twinkling Fiber break or optical power exceeds limit
LOS
OFF ONU accepts normal optical power