Product Data Sheet Rosemount 3144p Temperature Transmitter en 73128

Product Data Sheet
00813-0100-4021, Rev TB
May 2022
Rosemount™ 3144P Temperature Transmitter

with Rosemount X-well™ Technology
For every responsibility you have, you are confronted with a number of challenges. You have aggressive
production and quality targets, but inaccurate or unavailable temperature measurements create
unscheduled downtime and products that don't meet specifications. You may be manually running loops,
because you don’t trust your temperature measurement; this requires the attention of your maintenance
staff and cost money in lost production. Additionally, it is difficult to improve safety and comply with
government and company regulations when you don’t have the information or tools needed to prove your
compliance.
Companies are coming to Emerson because they know they need reliable measurements and visibility into
their temperature measurements in order to address these challenges and achieve their business
objectives. With the Rosemount 3144P Transmitter, you gain greater visibility into your temperature
processe, so you can improve safety, comply with regulations, make the most of your limited resources,
and reach your production and quality targets. By leveraging Rosemount X-well Technology, advanced
diagnostic capabilities, and the unparalleled reliability and accuracy of the transmitter, you can minimize
off-spec product, reduce maintenance and downtime, improve the usage of your limited resources, and
meet regulatory demands.
Rosemount 3144P May 2022
Features and benefits
™
Complete Point Solution for accurately measuring process temperature in
monitoring applications without the requirement of a thermowell or process
penetration
■ Simplify temperature measurement point specification, installation, and
maintenance and eliminate possible leak points.
■ Calculate a repeatable and accurate process temperature measurement with an
in-transmitter thermal conductivity algorithm.
■ Measure pipe surface and ambient temperature and use the thermal conductivity
properties of the installation and process piping in order to provide an accurate
process measurement.
Access information when you need it with asset tags

Newly shipped devices include a unique QR code asset tag, which enables you to access serialized information directly from the
device. With this capability, you can:
■ Access device drawings, diagrams, technical documentation, and troubleshooting information in your MyEmerson account.
■ Improve mean time to repair and maintenance efficiency.
■ Ensure confidence that you have located the correct device.
■ Eliminate the time-consuming process of locating and transcribing nameplates to view asset information.
Contents
Features and benefits........................................................................................................................................................................ 2
Ordering information........................................................................................................................................................................ 5
How to order Rosemount X-well Technology...................................................................................................................................12
Specifications.................................................................................................................................................................................. 13
Product certifications...................................................................................................................................................................... 26
Dimensional drawings..................................................................................................................................................................... 35
2 Emerson.com/Rosemount
May 2022 Rosemount 3144P
Deliver unmatched field reliability and innovative process measurement

solutions
■ Superior accuracy and stability
■ Dual and single sensor capability with universal sensor inputs (RTD,
thermocouple, mV, ohms)
■ Comprehensive sensor and process diagnostics offering
■ SIL3 capable: IEC 61508 certified by an accredited third party agency for use
in safety instrumented systems up to SIL 3 (minimum requirement of single
use [1oo1] for SIL 2 and redundant use [1oo2] for SIL 3)
■ Dual-compartment housing
■ Large LCD display
■ 4–20 mA HART® with selectable revisions (5 and 7)
■ FOUNDATION™ Fieldbus, compliant to ITK 6.0 and NE107 standards
Improve efficiency with best-in-class product specifications and capabilities

■ Reduce maintenance and improve performance with industry leading accuracy and stability.
■ Improve measurement accuracy by 75 percent with transmitter-sensor matching.
■ Ensure process health with system alerts and user-friendly device dashboards.
■ Easily check device status and values on local LCD display with large percent range graph.
■ Achieve high reliability and installation ease with the industry's most rugged dual compartment design.
Optimize measurement reliability with diagnostics designed for any protocol

on any host system
■ Thermocouple degradation diagnostic monitors the health of a
thermocouple loop, enabling preventative maintenance.
■ Minimum and maximum temperature tracking tracks and
records temperature extremes of the process sensors and the
ambient environment.
■ Sensor drift alert detects sensor drift and alerts the user.
■ The Hot Backup™ feature provides temperature measurement
redundancy.
Emerson.com/Rosemount 3
Explore the benefits of a Complete Point Solution from Emerson

■ An “Assemble To Sensor” option enables Emerson to
provide a complete point temperature solution, delivering
an installation-ready transmitter and sensor assembly.
■ Emerson offers a selection of RTDs, thermocouples, and
thermowells that bring superior durability and Rosemount
reliability to temperature sensing, complementing the
Rosemount Transmitter portfolio.
Experience global consistency and local support from numerous worldwide

Emerson manufacturing sites
■ World-class manufacturing provides globally consistent
products from every factory and the capacity to fulfill the
needs of any project, large or small.
■ Experienced instrumentation consultants help select the
right product for any temperature application and advise on
best installation practices.
■ An extensive global network of Emerson service and support
personnel can be on-site when and where they are needed.
■ Make wireless installation and configuration easy with the
Emerson Wireless Gateway.
Looking for a wireless temperature solution? For wireless applications that require superior performance and unmatched reliability,
consider the Rosemount 648 Wireless Temperature Transmitter.
Ordering information
The industry-leading Rosemount 3144P Single Point Temperature
Transmitter delivers unmatched field reliability and innovative process
measurement solutions and diagnostics.
Transmitter features include:
■ Temperature measurement assembly with Rosemount X-well
Technology (option code PT)
■ Dual and single sensor input capabilities
■ Transmitter-sensor matching (option code C2)
■ Integral transient protector (option code T1)
■ IEC 61508 Safety Certificate of Compliance (option code QT)
■ Advanced sensor and process diagnostics (option codes D01 and
DA1)
■ Large, easy to read LCD display (option code M5)
■ “Assemble to Sensor” option (option code XA)
CONFIGURE > VIEW PRODUCT >
Online product configurator

Many products are configurable online using our Product Configurator. Select the Configure button or visit our website to start.
With this tool's built-in logic and continuous validation, you can configure your products more quickly and accurately.
Model codes
Model codes contain the details related to each product. Exact model codes will vary; an example of a typical model code is shown
in Figure 1.
Figure 1: Model code example
1. Required model components (choices available on most)

2. Additional options (variety of features and functions that may be added to products)
Specifications and options

See the Specifications and options section for more details on each configuration. Specification and selection of product materials,
options, or components must be made by the purchaser of the equipment. See the Material selection section for more information.
Optimizing lead time

The starred offerings (★) represent the most common options and should be selected for best delivery. The non-starred offerings
are subject to additional delivery lead time.
Required model components
Model
Code Description
3144P Temperature transmitter ★
Housing style
Code Description Material Conduit entry size

D1 Field mount housing, dual- Aluminum ½–14-in. NPT ★
compartment housing
D2 Field mount housing, dual- Aluminum M20 x 1.5 (CM20) ★
compartment housing
D3 Field mount housing, dual- Aluminum PG 13.5 (PG11) ★
compartment housing
D4 Field mount housing, dual- Aluminum JIS G ½ ★
compartment housing
D5 Field mount housing, dual- Stainless steel ½–14-in. NPT ★
compartment housing
D6 Field mount housing, dual- Stainless steel M20 x 1.5 (CM20) ★
compartment housing
D7 Field mount housing, dual- Stainless steel PG 13.5 (PG11) ★
compartment housing
D8 Field mount housing, dual- Stainless steel JIS G ½ ★
compartment housing
Transmitter output
Code Description
A 4—20 mA with digital signal based on HART® Protocol ★
F FOUNDATION™ Fieldbus digital signal (includes three analog input function block and backup link active scheduler) ★
Measurement configuration
Code Description
1 Single-sensor input ★
2 Dual-sensor input ★
Product certification
Code Description
NA No approval ★
E5 USA explosion proof, dust ignition proof, and non-incendive ★
I5(1) USA intrinsically safe (IS) and non-incendive (includes standard IS and FISCO for Fieldbus units) ★
K5(1) USA IS, non-incendive, and explosion-proof combination (includes standard IS and FISCO for Fieldbus units) ★
KB(1) USA and Canada IS, explosion-proof, and non-incendive combination (includes standard IS and FISCO for Fieldbus ★
units)
I6(1) Canada IS/FISCO, and Division 2 (includes standard IS and FISCO for Fieldbus units) ★
K6(1) Canada IS, FISCO Division 2, and explosion-proof combination (includes standard IS, FISCO for Fieldbus units) ★
E1 ATEX flameproof approval ★
N1 ATEX type n approval ★
I1(1) ATEX intrinsic safety approval (includes standard IS and FISCO for Fieldbus units) ★
K1(1) ATEX IS, flameproof, dust ignition-proof and type n combination (includes standard IS and FISCO for Fieldbus units) ★
ND ATEX dust ignition-proof approval ★
KA(1) ATEX/Canada intrinsic safety, explosion-proof combination (includes standard IS and FISCO for Fieldbus units) ★
E7 IECEx flameproof approval ★
N7 IECEx Type 'n' approval ★
I7(1)(2) IECEx intrinsic safety ★
K7(1)(2) IECEx intrinsic safety, flameproof, dust ignition-proof and type n combination ★
E2(2) Brazil flameproof ★
I2(2) Brazil intrinsic safety ★
E4(2) Japan flameproof approval ★
E3(2) China flameproof approval ★
I3(1)(2) China intrinsic safety ★
N3 China type n ★
KM Technical Regulations Customs Union (EAC) flameproof, intrinsic safety ★
IM Technical Regulations Customs Union (EAC) intrinsic safety ★
EM Technical Regulations Customs Union (EAC) flameproof ★
(1) When IS approval is ordered on a FOUNDATION® Fieldbus, both standard IS and FISCO IS approvals apply. The device label is marked appropriately.
(2) Consult factory for availability when ordering with HART® or FOUNDATION Fieldbus models.
Additional options
Plantweb™ control functionality
Code Description
A01 FOUNDATION™ Fieldbus advanced control function block suite ★
Plantweb advanced diagnostic functionality
Code Description
D01 FOUNDATION™ Fieldbus sensor and process diagnostic suite: thermocouple diagnostic, minimum/maximum tracking ★
DA1 HART™ sensor and process diagnostic suite: thermocouple diagnostic, minimum/maximum tracking ★
Enhanced performance
Code Description
PT(1) Temperature measurement assembly with Rosemount X-well Technology ★
P8(2) Enhanced transmitter accuracy ★
(1) Not available with FOUNDATION Fieldbus models.
(2) Enhanced accuracy only applies to RTDs; however the option can be ordered with any sensor type.
Mounting bracket
Code Description
B4 “U” mounting bracket for 2-in. pipe mounting - all SST ★
B5 “L” mounting bracket for 2-in. pipe or panel mounting - all SST ★
BH "L" mounting bracket for 2-in pipe or panel mounting - 316 SST ★
Display
Code Description
M5 LCD display ★
External ground
Code Description
G1 External ground lug assembly ★
Transient protector
Code Description
T1 Integral transient protector ★
Software configuration
Code Description
C1 Custom configuration of date, descriptor, and message (requires Configuration Data Sheet with order) ★
Line filter
Not available with FOUNDATION Fieldbus models.
Code Description
F5 50 Hz line voltage filter ★
Alarm level configuration

Not available with FOUNDATION™ Fieldbus models.
Code Description
A1 NAMUR alarm and saturation levels, high alarm ★
CN NAMUR alarm and saturation levels, low alarm ★
Low alarm
Code Description
C8 Low alarm (standard Rosemount alarm and saturation values) ★
Sensor trim
Code Description
C2 Transmitter-sensor matching – trim to PT100 RTD calibration schedule (Callendar-Van Dusen constants) ★
C7 Trim to non-standard sensor (special sensor–customer must provide sensor information)
Five-point calibration
Code Description
C4 5-point calibration (requires the Q4 option code to generate a calibration certificate) ★
Calibration certification
Code Description
Q4 Calibration certificate (3-point calibration) ★
QG Calibration certificate and GOST verification certificate ★
QP Calibration certificate and tamper evident seal ★
Dual-input custom configuration (only with measurement type option code 2)
Code Description
U1 Hot Backup™ ★
U2(1) Average temperature with Hot Backup and sensor drift alert – warning mode ★
U3(1) Average temperature with Hot Backup and sensor drift alert – alarm mode ★
Code Description
U5 Differential temperature ★
U6 Average temperature ★
U7 First good temperature ★
U4 Two independent sensors
(1) Not available with FOUNDATION™ Fieldbus models.
Custody transfer
Not available with FOUNDATION™ Fieldbus models.
Code Description
D3 Custody transfer approval (Canada)
D4 MID custody transfer (Europe)
Quality certification for safety

Code Description
QS Prior-use certificate of FMEDA data (HART® only) ★
QT Safety-certified to IEC 61508 with certificate of FMEDA data (HART only) ★
Cold temperature
Code Description
BR6 -76 °F (-60 °C) cold temperature operation ★
Conduit electrical connector

Available with intrinsically safe approvals only. For FM Intrinsically Safe or non-incendive approval (option code I5), install in
accordance with Rosemount drawing 03151-1009 to maintain 4X rating.
Code Description
GE M12, 4-pin, male connector (eurofast®) ★
GM A size mini, 4-pin, male connector (minifast®) ★
HART® revision configuration
Code Description
HR7 Configured for HART Revision 7 ★
Assemble to option
Code Description
XA Sensor specified separately and assembled to transmitter ★
Extended product warranty

Code Description
WR3 3-year limited warranty ★
WR5 5-year limited warranty ★
How to order Rosemount X-well Technology

Rosemount X-well™ Technology is for temperature monitoring applications and is not intended for control or safety applications. It
is available in the Rosemount 3144P Transmitter in a factory assembled direct mount configuration with a Rosemount 0085 Pipe
Clamp Sensor. It cannot be used in a remote mount configuration. Rosemount X-well Technology will only work as specified with
factory supplied and assembled Rosemount 0085 Sensor silver tipped single element sensor with an 3.15-in. (80 mm) extension
length. It will not work as specified if used with other sensors.
Table 1: Rosemount 3144P X-well Technology option code requirements
Code Description
D1-D4 Aluminum field mount housing
PT Temperature measurement assembled with Rosemount X-well Technology
A 4–20 mA with digital signal based on HART™ Protocol
XA Sensor specified separately and assembled to transmitter
C1 Custom configuration of date, descriptor, message, and wireless parameters (requires Configuration Data Sheet with
order)
HR7 Configured for HART Revision 7
Table 2: Rosemount 0085 Pipe Clamp Sensor option code requirements for use with X-well Technology
Code Description
N No connection head
3 Sensor connection
P1 Sensor type
J Extension type
0080 Extension length
XA Assemble sensor to specific temperature transmitter
Rosemount X-well assemblies are available in most Rosemount 0085 Pipe Clamp Sensor diameter sizes.
Typical model number of the assembly:

3144P D 1A 1 NA M5 PT C1 XA
0085 N 3 P1 J 0080 C 0169 N XA
Specifications
® ™
HART and FOUNDATION Fieldbus
Functional specifications
Inputs
User-selectable. See Table 3 for sensor options.
Output
Two-wire device with either 4–20 mA/HART®, linear with temperature or input, or completely digital output with FOUNDATION™
Fieldbus Communication (ITK 6.0.1 compliant).
Isolation
Input/output isolation specified to 500 Vdc (500 Vrms 707 V peak) at 50/60 Hz.
Humidity limits
0–99 percent relative humidity, non-condensing
Update time
Approximately 0.5 seconds for a single sensor (one second for dual sensors).
Physical specifications
Material selection
Emerson provides a variety of Rosemount products with various product options and configurations, including materials of
construction that can be expected to perform well in a wide range of applications. The Rosemount product information presented
is intended as a guide for the purchaser to make an appropriate selection for the application. It is the purchaser’s sole responsibility
to make a careful analysis of all process parameters (such as all chemical components, temperature, pressure, flow rate, abrasives,
contaminants, etc.), when specifying product, materials, options, and components for the particular application. Emerson is not in
a position to evaluate or guarantee the compatibility of the process fluid or other process parameters with the product, options,
configuration, or materials of construction selected.
Conformance to specification (±3σ [Sigma])
Technology leadership, advanced manufacturing techniques, and statistical process control ensure specification conformance to at
least ±3σ.
Conduit connections
The standard field mount housing has ½–14-in. NPT conduit entries. Additional conduit entry types are available, including PG13.5
(PG11), M20 3 1.5 (CM20), or JIS G ½. When any of these additional entry types are ordered, adapters are placed in the standard
field housing so these alternative conduit types fit correctly.
Materials of construction
Enclosure Low-copper aluminum or CF-8M (cast version of 316 stainless steel)

Paint Polyurethane
O-rings Buna N
Mounting specification
Transmitters may be attached directly to the sensor. Optional mounting brackets (codes B4 and B5) allow for remote mounting.
See Figure 6.
Transmitter weight
Aluminum 3.1 lb (1.4 kg)

Stainless steel 7.8 lb (3.5 kg)
Enclosure ratings
Type 4X
IP66 and IP68
Stability
RTDs: ±0.1 percent of reading or 0.1 °C (0.18 °F), whichever is greater, for two years for RTDs.
Thermocouples: ±0.1 percent of reading or 0.1 °C (0.18 °F), whichever is greater, for one year for thermocouples.
Five-year stability
RTDs: ±0.25% of reading or 0.25 °C, whichever is greater, for five years.
Thermocouples: ±0.5% of reading or 0.5 °C, whichever is greater, for five years.
Vibration effect
Tested to the following with no effect on performance per IEC 60770-1, 1999:
Frequency Vibration
10 to 60 Hz 0.21 mm displacement
60 to 2000 Hz 3 g peak acceleration
Self calibration
The analog-to-digital measurement circuitry automatically self-calibrates for each temperature update by comparing the dynamic
measurement to extremely stable and accurate internal reference elements.
Radio frequency interference (RFI) effect
Worst case RFI effect is equivalent to the transmitter’s nominal accuracy specification, according to , when tested in accordance
with IEC 61000-4-3, 30 V/m (HART®)/20 V/m (HART thermocouple (T/C)) /10 V/m (FOUNDATION Fieldbus), 80 to 1000 MHz, with
unshielded cable.
Electromagnetic compatibility (EMC)
Meets all industrial environment requirements of EN61326 and NAMUR NE-21. Maximum deviation <1% span during EMC
disturbance.
Note
During surge event, device may exceed maximum EMC deviation limit; however, device will self-recover and return to normal
operation within specified start-up time.
External ground screw assembly

The external ground screw assembly can be ordered by specifying code G1. However, some approvals include the ground screw
assembly in the transmitter shipment; hence it is not necessary to order code G1. The table below identifies which approval options
include the external ground screw assembly.
Approval type External ground screw

assembly included?(1)
E5, I1, I2, I5, I6, I7, K5, K6, KB, NA No–order option code G1
E1, E2, E3, E4, E7, K1, K7, KA, N1, N7, ND, NF Yes
(1) The parts contained with the G1 option are included with the Integral Protector option code T1. When ordering T1, the G1 option code does not
need to be ordered separately.
Hardware tag
■ No charge
■ Two lines of 28 characters (56 characters total)
■ Tags are stainless steel
■ Permanently attached to transmitter
■ Character height is 1/16-in. (1.6 mm)
■ A wire-on tag is available upon request. Five lines of 12 characters (60 characters total)
Software tag
■ HART® transmitter can store up to eight characters in HART 5 mode and 32 characters in HART 7 mode. FOUNDATION Fieldbus
transmitters can store up to 32 characters.
■ Can be ordered with different software and hardware tags.
■ If no software tag characters are specified, the first eight characters of the hardware tag are the default.
Transmitter accuracy
Table 3: Transmitter accuracy
Sensor options Sensor Input ranges Minimum span(1) Digital accuracy(2) Enhanced D/A
reference accuracy(3) accuracy
(4)(5)
2-, 3-, 4-wire RTDs °C °F °C °F °C °F °C

Pt 100 (α = IEC 751 –200 to –328 to 10 18 ± 0.10 ± 0.18 ± 0.08 ±0.02% of
0.00385) 850 1562 span
Rosemount X- (α = 0.00385) IEC 751 –58 to 10 18 ± 0.29 ± 0.52 N/A ±0.02% of
well Pt 100 572 span
Pt 200 (α = IEC 751 –200 to –328 to 10 18 ± 0.22 ± 0.40 ± 0.176 ±0.02% of
0.00385) 850 1562 span
Pt 500 (α = IEC 751 –200 to –328 to 10 18 ± 0.14 ± 0.25 ± 0.112 ±0.02% of
0.00385) 850 1562 span
Pt 1000 (α = IEC 751 –200 to –328 to 10 18 ± 0.10 ± 0.18 ± 0.08 ±0.02% of
0.00385) 300 1193 span
Pt 100 (α = JIS 1604 –200 to –328 to 10 18 ± 0.10 ± 0.18 ± 0.08 ±0.02% of
0.003916) 645 1193 span
Pt 200 (α = JIS 1604 –200 to –94 to 10 ± 0.22 ± 0.40 ± 0.40 ± 0.176 ±0.02% of
0.003916) 645 572 span
Table 3: Transmitter accuracy (continued)
(4)(5)
Ni 120 Edison curve –70 to –58 to 10 18 ± 0.08 ± 0.14 ± 0.064 ±0.02% of

no. 7 300 482 span
Cu 10 Edison copper –50 to –328 to 10 18 ±1.00 ± 1.80 ± 0.8 ±0.02% of
winding no. 15 250 1022 span
Pt 50 GOST 6651-94 –200 to –328 to 10 18 ±0.20 ±0.36 ± 0.16 ±0.02% of
(α=0.00391) 550 1022 span
Pt 100 GOST 6651-94 –200 to –328 to 10 18 ±0.10 ±0.18 ± 0.08 ±0.02% of
(α=0.00391) 550 1022 span
Cu 50 GOST 6651-94 –50 to –58 to 10 18 ±0.34 ±0.61 ± 0.272 ±0.02% of
(α=0.00426) 200 392 span
Cu 50 GOST 6651-94 –185 to –301 to 10 18 ±0.34 ±0.61 ± 0.272 ±0.02% of
(α=0.00428) 200 392 span
Cu 100 GOST 6651-94 –50 to –58 to 10 18 ±0.17 ±0.31 ± 0.136 ±0.02% of
(α=0.00426) 200 392 span
Cu 100 GOST 6651-94 –185 to –301 to 10 18 ±0.17 ±0.31 ± 0.136 ±0.02% of
(α=0.00428) 200 392 span
Thermocouples(6)
Type B(7) NIST 100 to 212 to 25 45 ± 0.75 ± 1.35 N/A ±0.02% of
monograph 1820 3308 span
175, IEC 584
Type E NIST –200 to –328 to 25 45 ± 0.20 ± 0.36 N/A ±0.02% of
175, IEC 584
Type J NIST –180 to –292 to 25 45 ± 0.25 ± 0.45 N/A ±0.02% of
175, IEC 584
Type K(8) NIST –180 to –292 to 25 45 ± 0.25 ± 0.45 N/A ±0.02% of
175, IEC 584
Type N NIST –200 to –328 to 25 45 ± 0.40 ± 0.72 N/A ±0.02% of
175, IEC 584
Type R NIST 0 to 32 to 25 45 ± 0.60 ± 1.08 N/A ±0.02% of
175, IEC 584
Type S NIST 0 to 32 to 25 45 ± 0.50 ± 0.90 N/A ±0.02% of
175, IEC 584
Type T NIST –200 to –328 to 25 45 ± 0.25 ± 0.45 N/A ±0.02% of
175, IEC 584
DIN Type L DIN 43710 –200 to –328 to 25 45 ± 0.35 ± 0.63 N/A ±0.02% of
900 1652 span
Table 3: Transmitter accuracy (continued)
(4)(5)
DIN Type U DIN 43710 –200 to –328 to 25 45 ± 0.35 ± 0.63 N/A ±0.02% of
600 1112 span
Type W5Re/ ASTM E 988-96 0 to 32 to 25 45 ± 0.70 ± 1.26 N/A ±0.02% of
W26Re 2000 3632 span
GOST Type L GOST R –200 to –392 to 25 45 ± 0.25 ± 0.45 N/A ±0.02% of
8.585–2001 800 1472 span
Other input types

Millivolt input –10 to 100 mV 3 mV ±0.015 mV N/A ±0.02% of
span
2-, 3-, 4-wire Ohm Input 0 to 2000 ohms 20 ohm ±0.35 ohm N/A ±0.02% of
span
(1) No minimum or maximum span restrictions within the input ranges. Recommended minimum span will hold noise within accuracy specification
with damping at zero seconds.
(2) Digital accuracy: digital output can be accessed by the Field Communicator.
(3) Enhanced accuracy can be ordered using the P8 model code.
(4) Total analog accuracy is the sum of digital and D/A accuracies.
(5) Applies to HART 4–20 mA devices.
(6) Total digital accuracy for thermocouple measurement: sum of digital accuracy +0.25 °C (0.45 °F) (cold junction accuracy)
(7) Digital accuracy for NIST Type B is ±3.0 °C (±5.4 °F) from 100 to 300 °C (212 to 572 °F).
(8) Digital accuracy for NIST Type K is ±0.50 °C (±0.9 °F) from –180 to –90 °C (–292 to –130 °F).
Reference accuracy example (HART Protocol only)

When using a Pt 100 (α = 0.00385) sensor input with a 0 to 100 °C span: Digital accuracy would be ±0.10 °C, D/A accuracy would be
±0.02% of 100 °C or ±0.02 °C, Total = ±0.12 °C.
Differential capability exists between any two sensor types (dual-sensor option)
For all differential configurations, the input range is X to Y where:
■ X = Sensor 1 minimum – Sensor 2 maximum and
■ Y = Sensor 1 maximum – Sensor 2 minimum
Digital accuracy for differential configurations (dual-sensor option, HART Protocol only)
■ Sensor types are similar (e.g., both RTDs or both thermocouples (T/Cs)): Digital accuracy = 1.5 times worst case accuracy of
either sensor type
■ Sensor types are dissimilar (e.g., one RTD, one T/C): Digital accuracy = Sensor 1 accuracy + Sensor 2 accuracy
Ambient temperature effect

Transmitters may be installed in locations where the ambient temperature is between –40 and 85 °C (–40 and 185 °F). To maintain
excellent accuracy performance, each transmitter is individually characterized over this ambient temperature range at the factory.
Table 4: Ambient temperature effect on cigital accuracy
Sensor options Sensor reference Effect per 1.0 °C (1.8 °F) Input temperature (T) D/A effect(3)
change in ambient(1)(2)
2-, 3-, or 4-wire RTDs
Pt 100 (α = 0.00385) IEC 751 0.0015 °C (0.0027 °F) Entire sensor input 0.001% of span
range
Table 4: Ambient temperature effect on cigital accuracy (continued)
Rosemount X-well Pt IEC 751 0.0058 °C (0.0104 °F) Entire sensor input 0.001% of span
100 (α = 0.00385) range
range
range
range
Pt 100 (α = 0.003916) JIS 1604 0.0015 °C (0.0027 °F) Entire sensor input 0.001% of span
range
Pt 200 (α = 0.003916) JIS 1604 0.0023 °C (0.00414 °F) Entire sensor input 0.001% of span
range
Ni 120 Edison curve no. 7 0.0010 °C (0.0018 °F) Entire sensor input 0.001% of span
range
Cu 10 Edison copper winding 0.015 °C (0.0027 °F) Entire sensor input 0.001% of span
no. 15 range
Pt 50 (α = 0.00391) GOST 6651-94 0.003 °C (0.0054 °F) Entire sensor input 0.001% of span
range
Pt 100 (α = 0.00391) GOST 6651-94 0.0015 °C (0.0027 °F) Entire sensor input 0.001% of span
range
Cu 50 (α = 0.00426) GOST 6651-94 0.003 °C (0.0054 °F) Entire sensor input 0.001% of span
range
range
range
range
Thermocouples
Type B NIST monograph 175, 0.014 °C T ≥ 1000 °C 0.001% of span
IEC 584 0.029 °C – 0.0021% of (T 300 °C ≤ T < 1000 °C
– 300) 100 °C ≤ T < 300 °C
0.046 °C – 0.0086% of (T
– 100)
Type E NIST monograph 175, 0.004 °C + 0.00043% of N/A 0.001% of span
IEC 584 T
Type J NIST monograph 175, 0.004 °C + 0.00029% of T ≥ 0 °C 0.001% of span
IEC 584 T T < 0 °C
0.004 °C + 0.0020% of
abs. val. T
Table 4: Ambient temperature effect on cigital accuracy (continued)
Type K NIST monograph 175, 0.005 °C + 0.00054% of T ≥ 0 °C 0.001% of span
IEC 584 T T < 0 °C
0.005 °C + 0.0020% of
abs. val. T
Type N NIST monograph 175, 0.005 °C + 0.00036% of All 0.001% of span
IEC 584 T
Type R NIST monograph 175, 0.015 °C T ≥ 200 °C 0.001% of span
IEC 584 0.021 °C – 0.0032% of T T < 200 °C
Type S NIST monograph 175, 0.015 °C T ≥ 200 °C 0.001% of span
IEC 584 0.021 °C – 0.0032% of T T < 200 °C
Type T NIST monograph 175, 0.005 °C T ≥ 0 °C 0.001% of span
IEC 584 0.005 °C + 0.0036% of T < 0 °C
abs. val. T
DIN Type L DIN 43710 0.0054 °C + 0.00029% of T ≥ 0 °C 0.001% of span
R T < 0 °C
0.0054 °C + 0.0025% of
abs. val. T
DIN Type U DIN 43710 0.0064 °C T ≥ 0 °C 0.001% of span
0.0064 °C + 0.0043% of T < 0 °C
abs. val. T
Type W5Re/W26Re ASTM E 988-96 0.016 °C T ≥ 200 °C 0.001% of span
0.023 °C + 0.0036% of T T < 200 °C
GOST Type L GOST R 8.585–2001 0.005 > 0 °C N/A 0.001% of span
0.005 - 0.003% < 0 °C
Other input types
Millivolt Input 0.00025 mV Entire sensor input 0.001% of span
range
2-, 3-, 4-wire Ohm Input 0.007 Ω Entire sensor input 0.001% of span
range
(1) Change in ambient is in reference to the calibration temperature of the transmitter (20 °C [68 °F]).
(2) Ambient temperature effect specification valid over minimum temperature span of 28 °C (50 °F).
(3) Applies to HART/4–20 mA devices.
Process temperature effects

Table 5: Ambient and process temperature difference effect on digital accuracy
Sensor option Sensor reference Effects per 1.0 °C(1.8 °F) Input temperature (T)
difference in ambient and
process temperature(1)
Rosemount X-well Pt 100 (α = IEC 751 ± 0.01 °C (0.018 °F) Entire sensor input range
0.00385)
(1) Valid under steady state process and ambient conditions.
Temperature effects example

When using a Pt 100 (α = 0.00385) sensor input with a 0 to 100 °C span at 30 °C ambient temperature, the following statements
would be true:
Digital temp effects

■ 0.0015 °C/°C x (30 - 20 °C) = 0.015 °C
D/A effects (HART/4–20 mA only)

■ [0.001%/°C of span] x 100 °C x |(30 - 20 °C)| = °C DA effect
■ [0.001%/°C x 100] x |(30 - 20)| = 0.01 °C
Worst case error

■ Digital + D/A + Digital temp effects + D/A effects
= 0.10 °C + 0.02 °C + 0.015 °C + 0.01 °C = 0.145 °C
Total probable error
Rosemount X-well temperature effects example

When using Rosemount X-well Technology at 30 °C ambient temperature and 100 °C process temperature:
Digital ambient temperature effects:

■ 0.0058 °C x (30 - 20) = 0.058 °C
Process temperature effects:

■ 0.01 °C x (100 - 30) = 0.70 °C
Worst case error:

■ Digital accuracy + Digital ambient temperature effects + Process temperature effects =
0.29 °C + 0.058 °C + 0.70 °C = 1.05 °C
Total probable error:
®
HART /4-20 mA specifications
Power supply
External power supply required. Transmitters operate on 12.0 to 42.4 Vdc transmitter terminal voltage (with 250 ohm load, 18.1
Vdc power supply voltage is required). Transmitter power terminals rated to 42.4 Vdc.
Wiring diagram
See Figure 8.
Alarms
Custom factory configurations of alarm and saturation levels are available for valid values with option code C1. These values can
also be configured in the field using a Field Communicator.
Transient protection (option code T1)

The transient protector helps to prevent damage to the transmitter from transients induced on the loop wiring by lightning,
welding, heavy electrical equipment, or switch gears. The transient protection electronics are contained in an add-on assembly that
attaches to the standard transmitter terminal block. The external ground lug assembly (code G1) is included with the transient
protector. The transient protector has been tested per the following standard:
■ IEEE C62.41-1991 (IEEE 587)/location categories B3. 6 kV/3 kA peak (1.2 x 50 μS Wave 8 x 20 μS combination wave) 6 kV/0.5 kA
peak (100 kHz ring wave) EFT, 4 kV peak, 2.5 kHz, 5 x 50 nS
■ Loop resistance added by protector: 22 ohmsmax.
■ Nominal clamping voltages: 90 V (common mode), 77 V (normal mode)
Local display
Optional five-digit LCD display includes 0–100% bar graph. Digits are 0.4 inches (8 mm) high. Display options include engineering
units (°F, °C, °R, K, ohms, and millivolts), percent, and milliamperes. The display can also be set to alternate between engineering
units/milliamperes, Sensor 1/Sensor 2, Sensor 1/Sensor 2/Differential Temperature, and Sensor 1/Sensor2/Average Temperature.
All display options, including the decimal point, may be reconfigured in the field using a Field Communicator or AMS Device
Manager.
Turn-on time
Performance within specifications is achieved less than six seconds after power is applied to the transmitter when the damping
value is set to zero seconds.
Power supply effect

Less than ±0.005 percent of span per volt.
SIS safety transmitter failure values

IEC 61508 Safety Certified SIL 2 and SIL 3 Claim Limit
■ Safety accuracy: Span ≥ 100 °C: ±2% of process variable span
■ Span < 100 °C: ±2 °C
■ Safety response time: five seconds
■ Safety specifications and FMEDA report available at Emerson.com/Rosemount/Support
■ Software suitable for SIL3 applications
Temperature limits
Table 6: Temperature limits
Description Operating limit Storage limit

Without LCD display –40 to 185 °F –76 to 250 °F
–40 to 85 °C –60 to 120 °C
Table 6: Temperature limits (continued)
Description Operating limit Storage limit

With LCD display(1) –40 to 185 °F –76 to 185 °F
–40 to 85 °C –60 to 85 °C
(1) LCD display may not be readable, and LCD display updates will be slower at temperatures below –4 °F (–20 °C).
Field Communicator connections

Field Communicator connections are permanently fixed to power/signal block.
Failure mode
The Rosemount 3144P features software and hardware failure mode detection. An independent circuit is designed to provide
backup alarm output if the microprocessor hardware or software fails.
The alarm level is user-selectable using the failure mode switch. If failure occurs, the position of the hardware switch determines
the direction in which the output is driven (HIGH or LOW). The switch feeds into the digital-to-analog (D/A) converter, which drives
the proper alarm output even if the microprocessor fails. The values at which the transmitter drives its output in failure mode
depends on whether it is configured to standard, or NAMUR-compliant (NAMUR recommendation NE 43) operation. The values for
standard and NAMUR-compliant operation are as follows:
Table 7: Operation parameters
Standard(1) NAMUR-compliant(1)
Linear output 3.9 ≤ I ≤ 20.5 3.8 ≤ I ≤ 20.5
Fail high 21 ≤ I ≤ 23 (default) 21.5 ≤ I ≤ 23 (default)
Fail low I ≤ 3.75 I ≤ 3.6
(1) Measured in milliamperes.
Load limitations
Maximum load = 40.8 x (Supply voltage - 12.0) without transient protection (optional).
A. HART® and analog operating range

B. Analog only operating range
Note
HART communication requires a loop resistance between 250 and 1100 ohms. Do not communicate with the transmitter when
power is below 12 Vdc at the transmitter terminals.
™
FOUNDATION Fieldbus specifications
FOUNDATION Fieldbus device registration

Device tested and registered to ITK 6.0.1
Power supply
Powered over FOUNDATION Fieldbus with standard Fieldbus power supplies. Transmitters operate on 9.0 to 32.0 Vdc, 12 mA
maximum. Transmitter power terminals are rated to 42.4 Vdc.
Wiring diagram
See Figure 9.
Alarm
The AI function block allows the user to configure the alarms to HIGH-HIGH, HIGH, LOW, or LOW-LOW with a variety of priority
levels and hysteresis settings.
Transient protection (option code T1)

The transient protector helps to prevent damage to the transmitter from transients induced on the loop wiring by lightning,
welding, heavy electrical equipment, or switch gears. The transient protection electronics are contained in an add-on assembly that
attaches to the standard transmitter terminal block. The transient terminal block is not polarity insensitive. The transient protector
has been tested to the following standard:
■ IEEE C62.41-1991 (IEEE 587)/location categories B3. 6 kV/3 kA peak (1.2 x 50 μS wave 8 x 20 μS combination wave) 6 kV/0.5 kA
peak (100 kHz ring wave) EFT, 4 kV peak, 2.5 kHz, 5*50 nS
■ Loop resistance added by protector: 22 ohms, maximum
■ Nominal clamping voltages: 90 V (common mode), 77 V (normal mode)
Diagnostics suite for FOUNDATION Fieldbus (option code D01)

The Rosemount 3144P Diagnostics Suite for FOUNDATION Fieldbus provides advanced functionality in the form of Statistical Process
Monitoring (SPM), a thermocouple diagnostic, and sensor drift alert. SPM technology calculates the mean and standard deviation
of the process variable and makes them available to the user. This may be used to detect abnormal process situations.
The thermocouple diagnostic enables the transmitter to measure and monitor the resistance of thermocouple loops in order to
detect drift or changing wiring connections.
Sensor drift alert allows the user to monitor the difference in measurement between two sensors installed in one process point. A
change in this differential value may indicate drifting sensors.
Local display
Displays all DS_65 measurements in the transducer and function blocks including Sensor 1, Sensor 2, differential, and terminal
temperatures. The display alternates up to four selected items. The meter can display up to five digits in engineering units (°F, °C,
°R, K, Ω, and millivolts). Display settings are configured at the factory according to the transmitter configuration (standard or
custom). These settings can be reconfigured in the field using a Field Communicator or DeltaV. In addition, the LCD display
provides the ability to display DS_65 parameters from other devices. In addition to the configuration of the meter, sensor
diagnostic data is displayed. If the measurement status is Good, the measured value is shown. If the measurement status is
Uncertain, the status indicating uncertain is shown in addition to the measured value. If the measurement status is Bad, the reason
for the bad measurement is shown.
Note
When ordering a spare electronics module assembly, the LCD display transducer block will display the default parameter.
Turn-on time
Performance within specifications is achieved less than 20 seconds after power is applied to the transmitter when the damping
value is set to zero seconds.
Status
The device is compliant to NAMUR NE 107, ensuring consistent, reliable, and standardized device diagnostic information.
The new standard is designed to improve the way device status and diagnostic information is communicated to operators and
maintenance personnel in order to increase productivity and reduce costs.
If self-diagnostics detect a sensor burnout or a transmitter failure, the status of the measurement will be updated accordingly. The
status may also send the PID output to a safe value.
FOUNDATION Fieldbus parameters

Schedule entries 25 (max)
Links 30 (max)
Virtual Communications 20 (max)
Relationships (VCR)
Function blocks
■ All blocks will ship with unique block names, e.g. AI_1400_XXXX.
■ All blocks shall be instantiated to avoid invalid defaults.
■ All Rosemount 3144P FOUNDATION Fieldbus have parameter COMPATIBILITY_REV for backward compatibility.
■ Parameters will be initialized to common values for easier bench configuration.
■ All default block tags are less than or equal to 16 characters in length to avoid inconvenience of apparently identical tags.
■ Default block tags include underscores, “_”, instead of whitespaces for easier configuration.
Resource block
■ Contains physical transmitter information including available memory, manufacture identification, device type, software tag,
and unique identification.
■ Plantweb™ Alerts enable the full power of the PW digital architecture by diagnosing instrumentation issues, communicating the
details, and recommending a solution.
Transducer block
■ Contains the actual temperature measurement data, including sensor 1, sensor 2, and terminal temperature.
■ Includes information about sensor type and configuration, engineering units, linearization, range, damping, and diagnostics.
■ Device Revision 3 and above includes Hot Backup functionality in the transducer block.
LCD display block (when an LCD display is used)

■ Configures the local display.
Analog input (AI)

■ Processes the measurement and makes it available on the Fieldbus segment.
■ Allows filtering, engineering unit, and alarm changes.
■ All devices ship with the AI blocks scheduled, meaning no configuration is needed if the factory default channels are used.
PID block (provides control functionality)

■ Performs single loop, cascade, or feedforward control in the field.
Block Execution time

Resource N/A
Transducer N/A
LCD display block N/A
Advanced diagnostics N/A
Analog input 1, 2, 3, 4 60 milliseconds
PID 1 and 2 with autotune 90 milliseconds
Input selector 65 milliseconds
Signal characterizer 60 milliseconds
Arithmetic 60 milliseconds
Output splitter 60 milliseconds
Product certifications
Rev 2.15
European Directive information

A copy of the EU Declaration of Conformity can be found at the end of this guide. The most recent revision of the EU Declaration of
Conformity can be found at Emerson.com/Rosemount.
Ordinary location certification

As standard, the transmitter has been examined and tested to determine that the design meets the basic electrical, mechanical,
and fire protection requirements by FM Approvals, a nationally recognized test laboratory (NRTL) as accredited by the Federal
Occupational Safety and Health Administration (OSHA).
North America
E5 USA explosionproof, dust-ignitionproof, and nonincendive

Certificate FM16US0202X
Standards FM Class 3600: 2011, FM Class 3611: 2004, FM Class 3615: 2006, FM Class 3810: 2005, ANSI/NEMA 250: 1991,
ANSI/ISA 60079-0: 2009, ANSI/ISA 60079-11: 2009
Markings XP CL I, DIV 1, GP A, B, C, D; T5(-50 °C ≤ Ta ≤ +85 °C);
DIP CL II/III, DIV 1, GP E, F, G; T5(-50 °C ≤ Ta ≤ +75 °C); T6(-50 °C ≤ Ta ≤ +60 °C); when installed per Rosemount drawing
03144-0320;
NI CL I, DIV 2, GP A, B, C, D; T5(-60 °C ≤ Ta ≤ +75 °C); T6(-60 °C ≤ Ta ≤+60 °C); when installed per Rosemount drawing
03144-0321, 03144-5075.
I5 USA intrinsic safety and nonincendive

Certificate FM16US0202X
Standards FM Class 3600: 2011, FM Class 3610: 2010, FM Class 3611: 2004, FM Class 3810: 2005, ANSI/NEMA 250: 1991,
ANSI/ISA 60079-0: 2009, ANSI/ISA 60079-11: 2009
Markings IS CL I/II/III, DIV 1, GP A, B, C, D, E, F, G; T4(-60 °C ≤ Ta ≤ +60 °C);
IS [Entity] CL I, Zone 0, AEx ia IIC T4(-60 °C ≤ Ta ≤ +60 °C);
NI CL I, DIV 2, GP A, B, C, D; T5(-60 °C ≤ Ta ≤ +75 °C); T6(-60 °C ≤ Ta ≤ +60 °C); when installed per Rosemount drawing
03144-0321, 03144-5075.
I6 Canada intrinisic safety and Division 2

Certificate 1242650
Standards CAN/CSA C22.2 No. 0-M91 (R2001), CAN/CSA-C22.2 No. 94-M91, CSA Std C22.2 No. 142-M1987, CAN/CSA-C22.2
No. 157-92, CSA Std C22.2 No. 213-M1987
Markings Intrinsically Safe for Class I, Groups A, B, C, D; Class II, Groups E, F, G; Class III;
[HART only zone markings]: Intrinsically Safe for Class I Zone 0 Group IIC; T4(-50 °C ≤ Ta ≤ +60 °C); Type 4X;
Suitable for Class I, Div. 2, Groups A, B, C, D;

[HART only zone markings]: Suitable for Class I Zone 2 Group IIC; T6(-60 °C ≤ Ta ≤ +60 °C); T5(-60 °C ≤ Ta ≤ +85 °C);
when installed per Rosemount drawing 03144-5076.
K6 Canada explosionproof, intrinsic safety, and Division 2

Certificate 1242650
Standards CAN/CSA C22.2 No. 0-M91 (R2001), CSA Std C22.2 No. 25-1966, CSA Std C22.2 No. 30-M1986; CAN/CSA-C22.2 No.
94-M91, CSA Std C22.2 No. 142-M1987, CAN/CSA-C22.2 No. 157-92, CSA Std C22.2 No. 213-M1987
Markings Explosionproof for Class I, Groups A, B, C, D; Class II, Groups E, F, G; Class III;
[HART® only zone markings]: Suitable for Class I, Zone 1, Group IIC; Intrinsically Safe for Class I, Groups A, B, C, D;
Class II, Groups E, F, G; Class III;
[HART only zone markings]: Suitable for Class I, Zone 0, Group IIC; T4(-50 °C ≤ Ta ≤ +60 °C); Type 4X; Suitable for Class
I, Div. 2, Groups A, B, C, D;
[HART only zone markings]: Suitable for Class I, Zone 2, Group IIC; T6(-60 °C ≤Ta ≤ +60 °C); T5(-60 °C ≤ Ta ≤ +85 °C);
when installed per Rosemount drawing 03144-5076.
Europe
E1 ATEX flameproof
Certificate DEKRA 19ATEX0076 X
Standards
EN IEC 60079-0: 2018, EN 60079-1: 2014
Specific Conditions of Use (X):

1. Flameproof joints are not intended for repair.
2. Non-standard paint options may cause risk from electrostatic discharge. Avoid installations that cause electrostatic build-up
on painted surfaces and only clean the painted surfaces with a damp cloth. If paint is ordered through a special option code,
contact the manufacturer for more information.
Additional Specific Conditions of Use (X) when “XA” designation is ordered:

1. Guard DIN style sensors against impacts greater than 4J.
Process temperature range at sensor Ambient temperature range (°C) Temperature class
connection(1) (°C).
-60 °C to +70 °C -60 °C to +70 °C T6
-60 °C to +80 °C -60 °C to +80 °C T5…T1
(1) Sensor connection is where the sensor threads into the transmitter or junction box housing
I1 ATEX Intrinsic Safety

Certificate BAS01ATEX1431X [HART]; Baseefa03ATEX0708X [Fieldbus]
Standards EN IEC 60079-0: 2018; EN 60079-11:2012
Markings
HART: II 1 G Ex ia IIC T5/T6 Ga; T6(-60 °C ≤ Ta ≤ +50 °C), T5(-60 °C ≤ Ta ≤ +75 °C)
Fieldbus: II 1 G Ex ia IIC T4 Ga; T4(-60 °C ≤ Ta ≤ +60 °C)
See Table 11 for entity parameters.
Special Conditions for Safe Use (X):

1. When fitted with the transient terminal options, the equipment is not capable of passing the 500 V insulation test. This
must be taken into account during installation.
2. The enclosure may be made from aluminum alloy with a protective polyurethane paint finish; however, care should be
taken to protect it from impact or abrasion when located in Zone 0.
N1 ATEX Type n
Certificate BAS01ATEX3432X [HART]; Baseefa03ATEX0709X [Fieldbus]
Standards EN IEC 60079-0:2018, EN 60079-15:2010
Markings
HART: II 3 G Ex nA IIC T5/T6 Gc; T6(-40 °C ≤ Ta ≤ +50 °C), T5(-40 °C ≤ Ta ≤ +75 °C);
Fieldbus: II 3 G Ex nA IIC T5 Gc; T5(-40 °C ≤ Ta ≤ +75 °C);
Special Condition for Safe Use (X):

When fitted with the transient terminal options, the equipment is not capable of passing the 500 V electrical strength test as
defined in clause 6.5.1 of EN 60079-15: 2010. This must be taken into account during installation.
ND ATEX dust
Certificate DEKRA 19ATEX0076 X
Standards EN IEC 60079-0:2018, EN 60079-31:2014
Markings
II 2 D Ex tb IIIC T130 °C Db, (-60 °C ≤ Ta ≤ +80 °C)
Specific Condition of Use (X):

Non-standard paint options may cause risk from electrostatic discharge. Avoid installations that cause electrostatic build-up on
painted surfaces and only clean the painted surfaces with a damp cloth. If paint is ordered through a special option code, contact
the manufacturer for more information.
Additional Specific Condition of Use (X) when “XA” designation is ordered:

The spring loaded adapter style sensors and DIN style sensors must be installed in a thermowell to maintain Ex tb protection.
Process temperature range at sensor Ambient temperature range (°C) Maximum surface temperature “T”
connection(1) (°C).
-60 °C to +80 °C -60 °C to +80 °C T130 °C
(1) Sensor connection is where the sensor threads into the transmitter or junction box housing
International
E7 IECEx flameproof
Certificate IECEx FMG 12.0022X
Standards IEC 60079-0:2011, IEC 60079-1:2014-06
Markings Ex db IIC T6…T1 Gb, T6(-50 °C ≤ Ta ≤ +40 °C), T5…T1(-50 °C ≤ Ta ≤ +60 °C)
See Process temperature limits for process temperatures.
Specific Conditions of Use (X):

1. See certificate for ambient temperature range.
2. The non-metallic label may store an electrostatic charge and become a source of ignition in Group III environments.
3. Guard the LCD display cover against impact energies greater than four joules.
5. A suitable certified Ex d or Ex tb enclosure is required to be connected to temperature probes with Enclosure option "N".
6. Care shall be taken by the end user to ensure that the external surface temperature on the equipment and the neck of DIN
style sensor probe does not exceed 266 °F (130 °C).
7. Non-standard paint options may cause risk of electrostatic discharge. Avoid installations that cause electrostatic build-up on
painted surfaces and only clean the painted surfaces with a damp cloth. If paint is ordered through a special option code,
Additionally available with option K7
IECEx Dust
Certificate IECEx FMG 12.0022X

Standards IEC 60079-0:2011 and IEC 60079-31:2013
Markings Ex tb IIIC T130 °C Db, (-40 °C ≤ Ta ≤ +70 °C); IP66
Specific conditions of use (X):

1. See certificate for ambient temperature range.
5. A suitable certified Ex d or Ex tb enclosure is required to be connected to temperature probes with Enclosure option "N".
6. Care shall be taken by the end user to ensure that the external surface temperature on the equipment and the neck of DIN
style sensor probe does not exceed 266 °F (130 °C).
7. Non-standard paint options may cause risk of electrostatic discharge. Avoid installations that cause electrostatic build-up on
painted surfaces and only clean the painted surfaces with a damp cloth. If paint is ordered through a special option code,
I7 IECEx intrinsic safety

Certificate IECEx BAS 07.0002X [HART]; IECEx BAS 07.0004X [Fieldbus]
Standards IEC 60079-0: 2017; IEC 60079-11: 2011
Markings HART: Ex ia IIC T5/T6 Ga; T6(-60 °C ≤ Ta ≤ +50 °C), T5(-60 °C ≤ Ta ≤ +75 °C);
Fieldbus: Ex ia IIC T4 Ga; T4(-60 °C ≤ Ta ≤ +60 °C)

1. When fitted with the transient terminal options, the equipment is not capable of passing the 500 V electrical strength test
as defined in Clause 6.3.13 of IEC 60079-11: 2011. This must be taken into account during installation.
N7 IECEx Type n
Certificate IECEx BAS 07.0003X [HART®]; IECEx BAS 07.0005X [Fieldbus]
Standards IEC 60079-0:2017, IEC 60079-15:2010
Markings HART: Ex nA IIC T5/T6 Gc; T6(-40 °C ≤ Ta ≤ +50 °C), T5(-40 °C ≤ Ta ≤ +75 °C);
Fieldbus: Ex nA IIC T5 Gc; T5(-40 °C ≤ Ta ≤ +75 °C);

When fitted with the transient terminal options, the equipment is not capable of passing the 500 V electrical strength test as
defined in clause 6.5.1 of EN 60079-15: 2010. This must be taken into account during installation.
Brazil
E2 Brazil flameproof and dust

Certificate UL-BR 13.0535X
Standards ABNT NBR IEC 60079-0:2013; ABNT NBR IEC 60079-1:2016; ABNT NBR IEC 60079-31:2014
Markings Ex db IIC T6...T1 Gb; T6(-50 °C ≤ Ta ≤ +40 °C); T5...T1(-50 °C ≤ Ta ≤ +60 °C)
Ex tb IIIC T130 °C Db; IP66; (-40 °C ≤ Ta ≤ +70 °C)

1. See product description for ambient temperature limits and process temperature limits.
4. Consult the manufacturer if dimensional information on the flameproof joints is necessary.
I2 Brazil intrinsic safety [HART®]

Standards ABNT NBR IEC 60079-0:2013, ABNT NBR IEC 60079-11:2013
Markings Ex ia IIC T6 Ga (-60 °C < Ta < 50 °C), Ex ia IIC T5 Ga (-60 °C < Ta < 75 °C)

1. When fitted with the transient terminal options, the equipment is not capable of withstanding the 500 V electrical strength
test as defined in ABNT NBR IEC60079-11. This must be taken into account during installation.
taken to protect it from impact and abrasion when located in areas that require EPL Ga (Zone 0).
Brazil intrinsic safety [Fieldbus/FISCO]

Standards ABNT NBR IEC 60079-0:2013, ABNT NBR IEC 60079-11:2013
Markings Ex ia IIC T4 Ga (-60 °C < Ta < +60 °C)
See Table 11 at the end of the Product Certifications section for Entity Parameters

1. When fitted with the transient terminal options, the equipment is not capable of withstanding the 500 V electrical strength
test as defined in ABNT NBR IEC60079-11. This must be taken into account during installation.
taken to protect it from impact and abrasion when located in areas that require EPL Ga (Zone 0).
China
E3 China flameproof
Certificate GYJ21.1277X
Standards GB3836.1-2010, GB3836.2-2010
Markings Ex d IIC T6~T1 Gb
I3 China intrinsic safety

Certificate GYJ21.1278X
Standards GB3836.1-2010, GB3836.4-2010, GB3836.20-2010
Markings Ex ia IIC T4~T6 Ga
N3 China Type n
Certificate GYJ20.1086X [Fieldbus]; GYJ20.1091X [HART®]
Standards GB3836.1-2010, GB3836.8-2014
Markings Ex nA IIC T5 Gc [Fieldbus]; Ex nA IIC T5/T6 Gc [HART]
Output T code Ambient temperature

Fieldbus T5 -40 °C ≤ Ta ≤ +75 °C
HART T6 -40 °C ≤ Ta ≤ +50 °C
T5 -40 °C ≤ Ta ≤ +75 °C
EAC - Belarus, Kazakhstan, Russia
EM Technical Regulation Customs Union (EAC) flameproof

Standards GOST 31610.0-2014, GOST IEC 60079-1-2013
Markings 1Ex db IIC T6…T1 Gb X, T6(-50 °C ≤ Ta ≤ +40 °C), T5…T1(-50 °C ≤ Ta ≤ +60 °C)

Non-standard paint options may cause risk of electrostatic discharge. Avoid installations that cause electrostatic build-up on
painted surfaces and only clean the painted surfaces with a damp cloth. If paint is ordered through a special option code, contact
the manufacturer for more information.
IM Technical Regulation Customs Union (EAC) intrinsic safety

Standards GOST 31610.0-2014, GOST IEC 60079-11-2014
Markings [HART®]: 0Ex ia IIC T5, T6 Ga X, T6(-60 °C ≤ Ta ≤ +50 °C), T5(-60 °C ≤ Ta ≤ +75 °C);
[Fieldbus/PROFIBUS®]: 0Ex ia IIC T4 Ga X, T4(-60 °C ≤ Ta ≤ +60 °C)

1. When fitted with the transient terminal options, the apparatus is not capable of withstanding the 500 V electrical strength
test as defined in Clause 6.3.13 of GOST 31610.11-2014. This must be taken into account during installation.
KM Technical Regulation Customs Union (EAC) flameproof, intrinsic safety, and dust
Standards GOST 31610.0-2014, GOST IEC 60079-1-2013, GOST IEC 60079-11-2014, GOST IEC 60079-31-2013
Markings Ex tb IIIC T130 °C Db X (-40 °C ≤ Ta ≤ +70 °C), IP66 in addition to markings listed for EM and IM above.

See certificate for special conditions.
Japan
E4 Japan flameproof
Certificate CML 17JPN1316X
Markings Ex db IIC T6…T1 Gb; T6 (-50 °C ≤ Ta ≤ +40 °C); T5...T1 (-50 °C ≤ Ta ≤ +60 °C)
Special Conditions for Safe Use:

2. Models with LCD display cover shall have the display cover protected from impact energies greater than 4 Joules.
3. For Models 65 and 185, the user shall ensure the external surface temperature of the equipment and the neck of the DIN
style probe does not exceed 130 °C.
4. Non-standard paint options may cause risk from electrostatic discharge.
5. The wiring used shall be suitable for temperature over 80 °C.
Korea
EP Korea flameproof
Certificate 10-KB4BO-0011X (flameproof), 17-KA4BO-0356X (dust)
Markings Ex db IIC Gb T6…T1; T6(-40 °C ≤ Tamb ≤ +40 °C), T5(-40 °C ≤ Tamb ≤ +60 °C)
Ex tb IIIC T130 °C Db

IP Korea intrinsic safety

Certificate 09-KB4BO-0028X
Markings Ex ia IIC T6/T5 Ga; T6(-60 °C ≤ Tamb ≤ +50 °C), T5(-60 °C ≤ Tamb ≤ +75 °C)

Combinations
K1 Combination of E1, I1, N1, and ND
K2 Combination of E2 and I2
K5 Combination of E5 and I5
KB Combination of K5, I6, and K6
KP Combination of EP and IP
Tables
Process temperature limits
Table 8: Sensor only (no transmitter installed)
Extension length Process temperature [˚C]

Gas Dust
T6 T5 T4 T3 T2 T1 T130 °C
Any extension length 85 100 135 200 300 450 130
Table 9: Transmitter

Gas Dust
T6 T5 T4 T3 T2 T1 T130 °C
No extension 55 70 100 170 280 440 100
3-in. extension 55 70 110 190 300 450 110
6-in. extension 60 70 120 200 300 450 110
9-in. extension 65 75 130 200 300 450 120
Adhering to the process temperature limitations of Table 10 will ensure that the service temperature limitations of the LCD display
cover are not exceeded. Process temperatures may exceed the limits defined in Table 10 if the temperature of the LCD display
cover is verified to not exceed the service temperatures in Table 10 and the process temperatures do not exceed the values
specified in Table 9.
Table 10: Transmitter with LCD display cover

Gas Dust
T6 T5 T4...T1 T130 °C
No extension 55 70 95 95
3-in. extension 55 70 100 100
6-in. extension 60 70 100 100
9-in. extension 65 75 110 110
Any extension length 65 75 95 95
Entity parameters
Table 11: Entity parameters
Parameters HART® Fieldbus/PROFIBUS FISCO

Voltage Ui (V) 30 30 17.5
Current Ii (mA) 300 300 380
Power Pi (W) 1 1.3 5.32
Capacitance Ci (nF) 5 2.1 2.1
Inductance Li (mH) 0 0 0
Additional certifications
SBS American Bureau of Shipping (ABS) type approval
Certificate 21-2097596-PDA
Intended use Measurement of temperature for marine and offshore applications
SBV Bureau Veritas (BV) type approval
Certificate 23154
Requirements Bureau Veritas rules for the classification of steel ships
Application Class notations: AUT-UMS, AUT-CCS, AUT-PORT and AUT-IMS; temperature transmitter type 3144P cannot be
installed on diesel engines.
SDN Det Norske Veritas (DNV) type approval
Certificate TAA00001JK
Intended use Det Norske Veritas’ rules for classification of ships, high speed, and light craft and Det Norske Veritas' offshore
standards
Application Table 12: Location classes
Temperature D
Humidity B
Vibration A
Table 12: Location classes (continued)
EMC A
Enclosure D
SLL Lloyds Register (LR) type approval
Certificate LR21173788TA
Application Environmental categories ENV1, ENV2, ENV3, and ENV5
Dimensional drawings
Figure 2: Transmitter exploded view
F
E
A. Cover with wiring diagram

B. Name plate
C. Electronic module
D. LCD display
E. Display cover
F. Housing with permanent terminal block
Figure 3: Switch location and LCD display face plate
4.37-
in.(110,9 m m )
4.40-
in.(111,8 m m )
A. Switches(1)
B. LCD display connector
Dimensions are in inches (millimeters).
Figure 4: Transmitter view
Top view Side view
B 5.12-in.
A (129,9 mm) with
LCD display
4.33-in.
(110 mm)
4.40-in. (111,8 mm)

4.37-in.
(110,0 mm)
C
1.93-in.
(49,0 mm)
A
3/8-16 UN-2B
A. Conduit entry
B. Display cover
C. Name plate
(1) Alarm and write protect (HART®), simulate and write protect (FOUNDATION™ Fieldbus).
Figure 5: Transmitter for conduits with M20 3 1.5, PG 13.5 entries
Top view Front view

5.12-in. 4.02-in.
(129,9 mm) (102,1 mm)
0.43-in.
4.33-in. 0.64-in. (16, 3 mm)
(11 mm)
C
(110 mm)
1.00-in. (25,4 mm) A
4.37-in.
(110,0 mm)
4.40 in. 1.05-in.

B (111,8 mm) (26,7 mm)
1.93-in.
(49,0 mm) 3/8–16
UN–2B
A. Clearance required to remove cover

B. Adapters for M20 x 1.5, PG 13.5
C. Explosion/flameproof clamp (option code dependent)
Figure 6: Pipe mounting configurations with optional mounting bracket
1.00 (25,4)
2.31 (58,7)
4.62 (117,2)
4.00 (101,5)
2.00 (51)
3/8-16 bolt
A
4.80 (121,9)
3/8-16 bolt
A. For transmitter mounting

B. 2-in. U-bolt for pipe mounting
Figure 7: Rosemount X-well Assembly

6.000 4.400
[152,39] [111,76]
ØD
Figure 8: HART/4-20 mA
Rosemount 3144P single-sensor connections
Two-wire RTD and Three-wire RTD and Four-wire RTD and Thermocouples and RTD with compensation
Ohms Ohms(1) Ohms millivolts loop(2)
Rosemount 3144P dual-sensor connections
ΔT/Hot Backup/Dual ΔT/Hot Backup/Dual ΔT/Hot Backup/Dual ΔT/Hot Backup/Dual DT/Hot Backup/Dual
Sensor with two RTDs Sensor with two RTDs Sensor with RTDs/ Sensor with RTDs/ Sensor with two RTDs
Thermocouples(1) Thermocouples(1) with Compensation
Loop(1)
(1) Emerson provides four-wire sensors for all single-element RTDs. Use these RTDs in two-wire or three-wire configurations by leaving the unneeded
leads disconnected and insulated with electrical tape.
(2) Transmitter must be configured for a three-wire RTD in order to recognize an RTD with a compensation loop.
Figure 9: FOUNDATION Fieldbus
Rosemount 3144P single-sensor connections
Two-wire RTD and Three-wire RTD and Four-wire RTD and Thermocouples and RTD with compensation
Ohms Ohms(1) Ohms millivolts loop(2)
Rosemount 3144P dual-sensor connections
ΔT/Hot Backup/dual ΔT/Hot Backup/dual ΔT/Hot Backup/dual ΔT/Hot Backup/dual ΔT/Hot Backup/dual
sensor with two RTDs sensor with two RTDs sensor with RTDs/ sensor with RTDs/ sensor with two RTDs
thermocouples(1) thermocouples(1) with compensation
loop(1)
(1) Emerson provides four-wire sensors for all single-element RTDs. Use these RTDs in two-wire or three-wire configurations by leaving the unneeded
leads disconnected and insulated with electrical tape.
(2) Transmitter must be configured for a three-wire RTD in order to recognize an RTD with a compensation loop.
Transmitter standard configuration

Both standard and custom configuration settings may be changed. Unless specified, the transmitter will be shipped as follows:
Standard configuration
4 mA value/lower range (HART®/4–20 mA) measurement point LO (FOUNDATION™ Fieldbus) 0 °C
20 mA value/upper range (HART/4–20 mA) measurement point HI (FOUNDATION Fieldbus) 100 °C
Damping 5 seconds
Output Linear with
temperature
Failure mode (HART/4–20 mA) High
Line voltage filter 60 Hz
Software tag See Software tag
Optional integral display Units and mA/
sensor 1 units
Single-sensor option
Sensor type 4-wire, Pt 100 a =
0.00385 RTD
Primary variable (HART/4–20 mA) analog input (AI) 1400 (FOUNDATION Fieldbus) Sensor 1
Secondary variable AI 1600 (FOUNDATION Fieldbus) Terminal
temperature
Tertiary variable Not used
Quaternary variable Not used
Dual-sensor option
Sensor type Two 3-wire, Pt 100 a
= 0.00385 RTD
Primary variable (HART/4–20 mA) AI 1400 (FOUNDATION Fieldbus) Sensor 1
Secondary variable AI 1500 (FOUNDATION Fieldbus) Sensor 2
Tertiary variable AI 1600 (FOUNDATION Fieldbus) Terminal
temperature
Transmitter custom configuration

The Rosemount 3144P Temperature Transmitter can be ordered with custom configuration. The table below lists the requirements
necessary to specify a custom configuration.
Option code Requirements/specification

C1: Factory data(1) Date: day/month/year
Descriptor: 16 alphanumeric character
Message: 32 alphanumeric character
Custom alarm levels can be specified for configuration at the factory.
Rosemount X-well specific information: pipe material, pipe schedule, line size
C2: Transmitter-sensor matching The Rosemount 3144P Transmitter is designed to accept Callendar-van Dusen constants from
a calibrated RTD schedule and generate a custom curve to match any specific sensor curve.
Specify a Rosemount RTD sensor model on the order with a special characterization curve (V
or X8Q4 option). These constants will be programmed into the transmitter when this option is
selected.
C4: Five point calibration Will include five-point calibration at 0, 25, 50, 75, and 100% analog and digital output points.
Use with option code Q4 to obtain a Calibration Certificate.
C7: Special sensor Used for non-standard sensor, adding a special sensor or expanding input.
Customer must supply the non-standard sensor information.
Additional special curve will be added to sensor curve input choices.
A1: NAMUR-compliant, high Analog output levels compliant with NAMUR. Alarm is set to fail high.
alarm
CN: NAMUR-compliant, low Analog output levels compliant with NAMUR. Alarm is set to fail low.
alarm
C8: Low alarm Analog output levels compliant with Rosemount standard. Alarm is set to fail low.
F5: 50 Hz Line voltage filter Calibrated to 50 Hz line voltage filter.
(1) Configuration Data Sheet required.
To custom configure the Rosemount 3144P Transmitter with the dual-sensor option transmitter for one of the applications
described below, indicate the appropriate option code in the model number. If a sensor type is not specified, the transmitter will be
configured for two 3-wire Pt 100 (α = 0.00385) RTDs if any of the following option codes are selected.
Option code U1: Hot Backup

Primary usage Primary usage sets the transmitter to automatically use sensor 2 as the primary input if
sensor 1 fails. Switching from sensor 1 to sensor 2 is accomplished without any effect on
the analog signal. A digital alert will be sent in the event of a failed sensor.
Primary variable 1st good
Secondary variable Sensor 1
Tertiary variable Sensor 2
Quaternary variable Terminal temperature
Option code U2: average temperature with Hot Backup and sensor drift alert—warning mode
Primary usage Critical applications, such as safety interlocks and control loops. Outputs the average of
two measurements and sends a digital alert if temperature difference exceeds the set
maximum differential (Sensor Drift Alert – warning mode). If a sensor fails, an alert will
be sent digitally, and the primary variable will be reported as the remaining good sensor
value.
Primary variable Sensor average

Option code U3: average temperature with Hot Backup and sensor drift alert—alarm mode
Primary usage Critical applications, such as safety interlocks and control loops. Outputs the average of
two measurements and sets the analog output into alarm if temperature difference
exceeds the set maximum differential (sensor drift alert – alarm mode). If a sensor fails,
an alert will be sent digitally, and the primary variable will be reported as the remaining
good sensor value.
Option code U4: two independent sensors

Primary usage Used in non-critical applications where the digital output is used to measure two
separate process temperatures.
Primary variable Sensor 1
Tertiary variable Terminal temperature
Option code U5: differential temperature

Primary usage The differential temperature of two process temperatures is configured as the primary
variable. If the temperature difference exceeds the maximum differential, the analog
output will go into alarm. Primary Variable will be reported as a bad sensor value.
Primary variable Differential temperature
Option code U6: average temperature

Primary usage When average measurement of two different process temperatures is required. If a
sensor fails, the analog output will go into alarm, and the primary variable will report the
measurement of the remaining good sensor.
00813-0100-4021
Rev. TB
May 2022
For more information: Emerson.com

©2022 Emerson. All rights reserved.
Emerson Terms and Conditions of Sale are available upon

request. The Emerson logo is a trademark and service mark of
Emerson Electric Co. Rosemount is a mark of one of the
Emerson family of companies. All other marks are the property
of their respective owners.

Product Data Sheet Rosemount 3144p Temperature Transmitter en 73128

Uploaded by

Copyright:

Available Formats

Product Data Sheet Rosemount 3144p Temperature Transmitter en 73128

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Data Sheet Rosemount 3144p Temperature Transmitter en 73128

Uploaded by

Copyright:

Available Formats

Product Data Sheet

Rosemount™ 3144P Temperature Transmitter

Features and benefits

Access information when you need it with asset tags

Deliver unmatched field reliability and innovative process measurement

Improve efficiency with best-in-class product specifications and capabilities

Optimize measurement reliability with diagnostics designed for any protocol

Explore the benefits of a Complete Point Solution from Emerson

Experience global consistency and local support from numerous worldwide

CONFIGURE > VIEW PRODUCT >

Online product configurator

1. Required model components (choices available on most)

Specifications and options

Optimizing lead time

Required model components

Code Description Material Conduit entry size

Plantweb™ control functionality

Plantweb advanced diagnostic functionality

Alarm level configuration

Dual-input custom configuration (only with measurement type option code 2)

Quality certification for safety

Conduit electrical connector

HART® revision configuration

Extended product warranty

How to order Rosemount X-well Technology

Typical model number of the assembly:

Enclosure Low-copper aluminum or CF-8M (cast version of 316 stainless steel)

Aluminum 3.1 lb (1.4 kg)

External ground screw assembly

Approval type External ground screw

2-, 3-, 4-wire RTDs °C °F °C °F °C °F °C

Table 3: Transmitter accuracy (continued)

Ni 120 Edison curve –70 to –58 to 10 18 ± 0.08 ± 0.14 ± 0.064 ±0.02% of

Table 3: Transmitter accuracy (continued)

Other input types

Reference accuracy example (HART Protocol only)

Ambient temperature effect

Table 4: Ambient temperature effect on cigital accuracy (continued)

Table 4: Ambient temperature effect on cigital accuracy (continued)

Process temperature effects

Temperature effects example

Digital temp effects

D/A effects (HART/4–20 mA only)

Worst case error

Total probable error

Rosemount X-well temperature effects example

Digital ambient temperature effects:

Process temperature effects:

Worst case error:

Total probable error:

Transient protection (option code T1)

Power supply effect

SIS safety transmitter failure values

Description Operating limit Storage limit

Table 6: Temperature limits (continued)

Description Operating limit Storage limit

Field Communicator connections

A. HART® and analog operating range

FOUNDATION Fieldbus device registration