Scribd
Upload
32 views15 pages

Lab 7 - IPv6 Addressing

Uploaded by

kaisbarboura99
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
32 views15 pages

Lab 7 - IPv6 Addressing

Uploaded by

kaisbarboura99
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Lab 7 - IPv6 Addressing

Addressing Table
Device Interface IPv6 Address/Prefix Default Gateway

R1 G0/0 2001:db8:1:1::1/64 N/A

R1 G0/0
fe80::1 N/A

R1
G0/1 2001:db8:1:2::1/64 N/A

R1 G0/1
fe80::1 N/A

R1
S0/0/0 2001:db8:1:a001::2/64 N/A

R1 S0/0/0
fe80::1 N/A

Sales NIC 2001:db8:1:1::2/64 fe80::1


Billing NIC 2001:db8:1:1::3/64 fe80::1
Accounting NIC 2001:db8:1:1::4/64 fe80::1
Design NIC 2001:db8:1:2::2/64 fe80::1
Engineering NIC 2001:db8:1:2::3/64 fe80::1
CAD NIC 2001:db8:1:2::4/64 fe80::1
ISP S0/0/0 2001:db8:1:a001::1 fe80::1

Objectives
Part 1: Configure IPv6 Addressing on the Router
Part 2: Configure IPv6 Addressing on Servers
Part 3: Configure IPv6 Addressing on Clients
Part 4: Test and Verify Network Connectivity

Background
In this activity, you will practice configuring IPv6 addresses on a router, servers, and clients. You will also
practice verifying your IPv6 addressing implementation.

Part 1: Configure IPv6 Addressing on the Router


Step 1: Enable the router to forward IPv6 packets.
a. Click R1 and then the CLI tab. Press Enter.
Open a configuration window

b. Enter privileged EXEC mode.


c. Enter the ipv6 unicast-routing global configuration command. This command must be entered to enable
the router to forward IPv6 packets.
R1(config)# ipv6 unicast-routing

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Step 2: Configure IPv6 addressing on GigabitEthernet0/0.


a. Enter the commands necessary to move to interface configuration mode for GigabitEthernet0/0.
b. Configure the IPv6 address with the following command:
R1(config-if)# ipv6 address 2001:db8:1:1::1/64
c. Configure the link-local IPv6 address with the following command:
R1(config-if)# ipv6 address fe80::1 link-local
d. Activate the interface.
R1(config-if)# no shutdown

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Step 3: Configure IPv6 addressing on GigabitEthernet0/1.


a. Enter the commands necessary to move to interface configuration mode for GigabitEthernet0/1.
b. Refer to the Addressing Table for the correct IPv6 address.
c. Configure the IPv6 address, the link-local address and activate the interface.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Step 4: Configure IPv6 addressing on Serial0/0/0.


a. Enter the commands necessary to move to interface configuration mode for Serial0/0/0.
b. Refer to the Addressing Table for the correct IPv6 address.
c. Configure the IPv6 address, the link-local address and activate the interface.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

d.

Step 5: Verify IPv6 addressing on R1.


It is good practice to verify addressing when it is complete by comparing configured values with the values in
the addressing table.
a. Exit configuration mode on R1.
b. Verify the addressing configured by issuing the following command:
R1# show ipv6 interface brief
c. If any addresses are incorrect, repeat the steps above as necessary to make any corrections.
Note: To make a change in addressing with IPv6, you must remove the incorrect address or else both the
correct address and incorrect address will remain configured on the interface.
Example:
R1(config-if)# no ipv6 address 2001:db8:1:5::1/64
d. Save the router configuration to NVRAM.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Close a configuration window

Part 2: Configure IPv6 Addressing on the Servers


Step 1: Configure IPv6 addressing on the Accounting Server.
a. Click Accounting and click the Desktop tab > IP Configuration.
b. Set the IPv6 Address to 2001:db8:1:1::4 with a prefix of /64.
c. Set the IPv6 Gateway to the link-local address, fe80::1.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Step 2: Configure IPv6 addressing on the CAD Server.


Configure the CAD server with addresses as was done in Step 1. Refer to the Addressing Table for the
addresses to use.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Part 3: Configure IPv6 Addressing on the Clients


Step 1: Configure IPv6 addressing on the Sales and Billing Clients.
a. Click Billing and then select the Desktop tab followed by IP Configuration.
b. Set the IPv6 Address to 2001:db8:1:1::3 with a prefix of /64.
c. Set the IPv6 Gateway to the link-local address, fe80::1.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 8 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

d. Repeat Steps 1a through 1c for Sales. Refer to the Addressing Table for the IPv6 address.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 9 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Step 2: Configure IPv6 Addressing on the Engineering and Design Clients.


a. Click Engineering and then select the Desktop tab followed by IP Configuration.
b. Set the IPv6 Address to 2001:db8:1:2::3 with a prefix of /64.
c. Set the IPv6 Gateway to the link-local address, fe80::1.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 10 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

d. Repeat Steps 2a through 2c for Design. Refer to the Addressing Table for the IPv6 address.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 11 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Part 4: Test and Verify Network Connectivity


Step 1: Open the server web pages from the clients.
a. Click Sales and click the Desktop tab. Close the IP Configuration window, if necessary.
b. Click Web Browser. Enter 2001:db8:1:1::4 in the URL box and click Go. The Accounting website
should appear.
c. Enter 2001:db8:1:2::4 in the URL box and click Go. The CAD website should appear.
d. Repeat steps 1a through 1c for the rest of the clients.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 12 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 13 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

Step 2: Ping the ISP.


a. Click on any client.
b. Click the Desktop tab > Command Prompt.
c. Test connectivity to the ISP by entering the following command:
PC> ping 2001:db8:1:a001::1
d. Repeat the ping command with other clients until full connectivity is verified.

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 14 of 15 www.netacad.com
Lab 7 - IPv6 Addressing

End of Document

© 2013 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 15 of 15 www.netacad.com

You might also like