4 Channel Controller

with Audio Interface Built in

USER MANUAL (English) 01~

MANUEL D’UTILISATION (Français) ~
BENUTZERHANDBUCH (Deutsch) ~
GEBRUIKSAANWIJZING (Nederlands) ~
MANUAL DE INSTRUCCIONES (Español) ~
MANUALE DI ISTRUZIONI (Italiano) ~
SAFETY INSTRUCTIONS

1. Read these Instructions.

2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one winder
than the other. The wide blade is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Where a mains plug is used as the disconnect device, the disconnect device shall remain readily
operable.
16. Please keep the unit in a good environment.
17. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.

WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus
shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be
placed on the apparatus.
CAUTION: To reduce the risk of electric shock, do not remove any
DO NOT OPEN
cover. No user-serviceable parts inside. Refer servicing to qualified
RISK OF ELECTRIC SHOCK service personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.

CAUTION
To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade exposure.

2
INTRODUCTION

- Thank you very much for purchasing 4MIX! -

Welcome to the 4MIX – A fully capable 4-deck DJ controller with integrated audio interface.
Direct 4-Deck Control
The 4MIX is a compact USB DJ controller that provides direct access to 4-decks. The mixer area is a familiar
4-channel mixer with 3-band EQ, CUE, volume and a filter knob for each channel. The 12 rubber buttons on
each deck provide direct access to Loop, Hot Cue, and Transport controls. The 4Mix has also been configured
to use the volume knob and play buttons for direct access to Virtual DJs Sampler feature.
Integrated Audio Interface
The low latency integrated audio interface provides not only master and monitoring headphone outputs, but also
a booth output with independent volume control. This allows the user to plug the unit directly into a club’s PA
system.
Virtual DJ LE Included
The 4Mix includes the popular Virtual DJ LE software. The included software is fully integrated with the 4Mix to
control 4 decks.

This document is organized in below sections: Box Contents:

A – Minimum System Requirements ► 4MIX
B – Connecting the 4MIX ► USB Cable
C – Start using the 4MIX ► User Manual
D – Front and Rear Panels Features ► Virtual DJ LE Setup CD
E – Specification (with Audio driver)

Features:
• Large platters for accurate control and scratching
• 4 deck layout with complete mixer
• USB MIDI controller compatible with all DJ MIDI software
• Low latency audio driver included
• Built-in audio connection for both preview and master outputs
• Large knobs for direct access to filter
• 24 rubber pads for direct access to Cue, Loop and Transport Control
• USB-powered device, no additional power supply required
• Includes Virtual DJ LE

A. Minimum System Requirements

PC: MAC:
‧Windows XP (SP3)/ Windows Vista/ Windows 7 ‧Mac OS X v10.5.x or above
‧Intel® Pentium 4 or AMD Athlon™ XP ‧Intel® processor
‧CD-ROM Drive ‧CD-ROM Drive
‧512MB RAM, 200MB Free Space ‧512MB RAM, 200MB Free Space
‧USB port ‧USB port

B. Connecting the 4MIX

3
C. Start Using the 4MIX
1. Insert the Virtual DJ LE Setup CD into computer CD-ROM drive.
i) For PC, The installer should start automatically. If not, browse the CD-ROM and double click on the file
“install_virtualdj_v#.msi”
ii) For Mac, The installation should start automatically. If not, browse the CD-ROM and double click on the file
“install_virtualdj_v#.pkg”
Please follow the on screen instructions to finish the installation.
It is recommended for users to create an account with Virtual DJ and register the software to get the latest
update on the software. Visit Virtual DJ website at http://www.virtualdj.com/users/.
2. For Windows users, please install the Audio driver for the 4MIX from the Software CD “Drivers” folder. Select
your operating system and install the driver. (Audio driver also available on http://www.djtechpro.com).
For Mac users, no audio driver is needed.
3. You may need to power on/ off the 4MIX when installing the driver.
4. Connect the 4MIX as in Section B and power on. Open the Virtual DJ LE software. You will be asked to enter
the serial number of the software. The serial number can be found on the paper pocket of the Setup CD.
5. Audio Configuration in Virtual DJ LE:
For PC (Shown below in Windows XP) For Mac

1. Open Virtual DJ LE and Click “CONFIG” 1. Open Virtual DJ LE and Click “CONFIG”
2. Select “HEADPHONES” 2. Select “HEADPHONES”
3. Select “ASIO DRIVER” 3. Select “4-OUT CARD”
4. Select “4-Mix ASIO driver” 4. Select “DJ-Tech 4-Mix”
5. Select ”Master: Chan 1&2/ Headphones: Chan 5. Select ”Master: Chan 1&2/ Headphones: Chan
3&4” 3&4”
6. Click OK to confirm 6. Click OK to confirm

D. Panel Features Front Panel

1. Mic Input Jack – Microphone input. 3. Mic Tone – This knob is used to adjust the tone of the

The included Virtual DJ LE does not support microphone.
4. CUE MIX – Adjust the mix of master output and
the Microphone Input. Please upgrade to full
monitoring output to your headphones in Virtual DJ.
version of Virtual DJ or use other DJ software
5. Monitor Level – This knob is used to adjust the
that supports microphone input. headphones output level.
2. Mic Level – This knob is used to adjust the 6. Monitor Headphone Jack – Connect to a pair of
microphone level. headphones
4
D. Panel Features Rear Panel

1. Power Connector - Plug in power adaptor here. DC adaptor can be used when the USB port cannot provide
enough power to the unit. Please use only a 6V DC adaptor.
2. Power Switch (Adaptor / OFF/ USB power) - Set the switch to adaptor when using external DC adaptor.
Set to USB bus power when using power from the computer via USB.
3. USB Socket - Used to connect a computer.
4. C.F Curve Control - Adjusts the shape of the
crossfader curve from a quick cut for scratching or to a
longer fade for mixing.
5. Master Outputs - Left & Right line level output
(unbalanced RCA).
6. Booth Outputs – Outputs for booth monitor.

The included Virtual DJ LE does not support the Booth Outputs. Please upgrade to full version of Virtual DJ or use
other DJ software that supports booth outputs.

D. Panel Features Top Panel

Please refer to the below for using the RELOADED and Virtual DJ LE
1. SAMPLER VOL knobs – Adjust the volume of samplers 1 to 4.
2. SAMPLER PLAY buttons – Toggle play/ pause of the samplers 1 to 4.
3. PEAK indicators – Illuminate when the channel volume is driven too high, which could cause distortion.
4. DECK EQ (High/ Mid/ Low) knobs – Adjust the EQ setting of the deck.
5. FILTER knobs – Adjust the filter setting for the deck. Filter is off when the knob position is at the middle.
6. CUE (PFL) Button – CUE (monitoring) Button for Decks
7. LOAD A/B/C/D button – Press to load the selected song to the desired deck.
8. TRACK SELECT encoder – Press to switch between the FOLDER TREE view, the SONG/FILE LIST view,
the AUTOMIX PLAYLIST view and the SIDELIST view in the BROWSER tab.
Turn to scroll up/ down the tree list or song list.
9. MASTER LEVEL meter – Indicate the master output level.
5
10. MASTER VOLUME knob
11. BOOTH VOLUME knob – Note: The included Virtual DJ LE does not support the Booth Outputs. Please upgrade to
full version of Virtual DJ or use other DJ software that supports booth outputs
12. SYNC buttons
13. HOT CUE buttons – Press to jump to the set HOT CUE. If the HOT CUE is not set yet, it will set the HOT
CUE.
14. PLAY/PAUSE buttons
15. CUE buttons
16. CUP buttons – Similar to the CUE buttons, but the song stop at the CUE point when the CUP button is held
down. And start playback from the CUE point when the CUP button is released.
17. SHIFT button – Press and hold to use with other controls for extended functions. Please refer to below
Shifted Controls Part
18. DECK VOLUME faders
19. CROSSFADER
20. RELOOP buttons – Press to activate the previously set loop.
21. OUT buttons – Press to set the OUT position of a manual loop. When it is already in a loop, press OUT
button to exit the loop.
22. IN buttons – Press to set the IN position of a manual loop.
23. DECK SELECT buttons – Press to switch between Deck A and Deck C for the left deck; and Deck B and
Deck B for the right deck. The left DECK SELECT button will turn on in amber when Deck C is selected. The
right DECK SELECT button will turn on in amber when Deck D is selected.
24. MULTI-FUNCTION JOG WHEEL – These jogs have different function according to the status of the VINYL
MODE button (25):
i) When VINYL MODE is off, turn the jog wheel for pitch adjustment.
ii) When VINYL MODE is on, turn the jog wheel for scratch function.
25. VINYL MODE buttons – Press to turn on/ off the VINYL MODE of the current deck. The Vinyl Mode will be
turned on every time when deck is switched (pressing DECK SELECT buttons).

Shifted Controls:
1. SAMPLER VOL knobs – Turn with SHIFT to adjust the effect parameter 1:
- S1 for DECK A - S2 for DECK B
- S3 for DECK C - S4 for DECK D
2. SAMPLER PLAY buttons – Press with SHIFT to turn on/ off the effect:
- S1 for DECK A - S2 for DECK B
- S3 for DECK C - S4 for DECK D
6. CUE (PFL) Button – Press with SHIFT to switch Crossfader assignment between left and right for the deck.
The button will be illuminated when the deck is assigned to the left side of the corssfader.
8. TRACK SELECT encoder – Turn this encoder with SHIFT to switch between the BROWSER/ SAMPLER/
EFFECTS and RECORD tabs.
12. SYNC buttons – Press with SHIFT for BEATLOCK Function
13. HOT CUE buttons – Press with SHIFT to delete the HOT CUE.
20. RELOOP buttons – Press with SHIFT to activate the autoloop of the deck.
21. OUT buttons –Press with SHIFT to increase AUTOLOOP size.
22. IN buttons – Press with SHIFT to decrease AUTOLOOP size
24. MULTI-FUNCTION JOG WHEEL – Turn with SHIFT for searching quickly on the current song no matter
SCRATCH MODE is on or off
25. VINYL MODE buttons – Press with SHIFT to select FX for the DECK

E. Specifications Audio I/O Configuration

INPUTS
1/2. Mic
OUTPUTS
1. Master Output L
2. Master Output R
3. Headphones Output L
4. Headphones Output R
5. Booth Output L
6. Booth Output R

6
E. SPECIFICATIONS

1. Input/Output impedance & sensitivity: (Maximum Gain, Load=100K ohm)

1-1 Input impedance and Reference input level:
Mic: 10K ohm /-54dBV +/-0.1dB

1-2 Output impedance:

Master: 1K ohm
Booth: 1K ohm
Phones (load=32 ohm): 4.7 ohm

2. USB Slave Player Section:

2-1 OUTPUT LEVEL (TCD782 TRK2)

Master OUT: 0dBV +/-1dB
Booth OUT: 0dBV +/-1dB
Monitor OUT: 1.5dBV +/-1dB

2-2 CHANNEL BALANCE: Within 2dB

2-3 FREQUENCY RESPONSE (TCD781 TRK1,4,16)

Master OUT: 17-16KHz +1/-3dB
Booth OUT: 17-16KHz +1/-3dB
Monitor OUT: 17-16KHz +1/-3dB

2-4 THD+N (TCD782 TRK2)

Master OUT: Less than 0.05%
Booth OUT: Less than 0.05%
Monitor OUT: Less than 0.1%

2-5 S/N RATIO (TCD782 TRK2,8)

Master OUT: More than 80dB
Booth OUT: More than 80dB
Monitor OUT: More than 75dB

2-6 L/R SEPARATION (TCD782 TRK9,11)

Master OUT: More than 80dB at 1KHz
Booth OUT: More than 80dB at 1KHz
Monitor OUT: More than 60dB at 1KHz

2-7 Recording and Playback: (Mic Input 1KHz -54dBV)

Master OUT: -14dBV +/-1dB
THD+N: OUT Less than 0.15%
TONE
-13 +/-3dB at 100Hz
-13 +/-3dB at 10KHz

3. Dimensions: 360 (W) x 255.8 (D) x 64.5 (H) mm

4. Weight: 2.23 kg

7
MIDI MAP (HEXADECIMAL)

CHANNEL
MIDI
I/O FUNCTION + FUNCTION CODE ACTION
CODE
MIDI CODE
Key
DECK 1
I S1 PLAY 09 9X (X=0) 22H 7FH：ON／00H：OFF
DECK 1
I S2 PLAY 09 9X (X=0) 23H 7FH：ON／00H：OFF
DECK 1
I S3 PLAY 09 9X (X=0) 24H 7FH：ON／00H：OFF
DECK 1
I S4 PLAY 09 9X (X=0) 25H 7FH：ON／00H：OFF
DECK 1
I CUE C 09 9X (X=0) 26H 7FH：ON／00H：OFF
DECK 1
I CUE A 09 9X (X=0) 27H 7FH：ON／00H：OFF
CUE B 09 28H DECK 1
I 9X (X=0) 7FH：ON／00H：OFF
CUE D 09 29H DECK 1
I 9X (X=0) 7FH：ON／00H：OFF
A 09 2AH DECK 1
I 9X (X=0) 7FH：ON／00H：OFF
2BH DECK 1
I B 09 9X (X=0) 7FH：ON／00H：OFF
2CH DECK 1
I C 09 9X (X=0) 7FH：ON／00H：OFF
DECK 1
I D 09 9X (X=0) 2DH 7FH：ON／00H：OFF
PRESS TO DECK 1
I 09 9X(X=0) 1FH 7FH：ON／00H：OFF
ENTER
9X(X=1,3) DECK A/C
VINYL 01H／41H
I 09 7FH：ON／00H：OFF
MODE 9X(X=2,4) DECK B/D
(SHIFT ON)
SWITCH
3AH
TO A
I DECK A/C 09 9X(X=0) 7FH：ON／00H：OFF
SWITCH
3BH
TO C
SWITCH
3CH
TO B
I DECK B/D 09 9X(X=0) 7FH：ON／00H：OFF
SWITCH
3DH
TO D
9X(X=1,3) DECK A/C
02H／42H
I IN 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
03H／43H
I OUT 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
04H／44H
I RE 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
05H／45H
I SYNC 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
06H／46H
I 1 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
07H／47H
I 2 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)

8
MIDI MAP (HEXADECIMAL)

CHANNEL
MIDI
I/O FUNCTION + FUNCTION CODE ACTION
CODE
MIDI CODE
9X(X=1,3) DECK A/C
08H／48H
I 3 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
09H／49H
I 4 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
I SHIFT 09 0EH 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
0AH／4AH
I CUP 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
0BH／4BH
I CUE 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
9X(X=1,3) DECK A/C
0CH／4CH
I 09 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
(SHIFT ON)
ENCODER/WHEEL

PRESS TO LEFT:40H-N／
I 0B BX(X=0) 1FH DECK 1
ENTER
RIGHT:40H+N
9X(X=1,3) DECK A/C
7FH：ON(WHEEL TURN
0FH／4FH
09
9X(X=2,4) ON)／00H： DECK B/D
(SHIFT ON)
I WHEEL
OFF(WHEEL STOP)
BX(X=1,3) DECK A/C
0FH／4FH LEFT:40H-N／
0B
BX(X=2,4) DECK B/D
(SHIFT ON) RIGHT:40H+N
VR
I S1 VOL 0B BX (X=0) 01H 00H~7F DECK 1
I S2 VOL 0B BX (X=0) 02H 00H~7F DECK 1
I S3 VOL 0B BX (X=0) 03H 00H~7F DECK 1
I S4 VOL 0B BX (X=0) 04H 00H~7F DECK 1
I C HI 0B BX(X=0) 05H 00H~7F DECK 1
I C MID 0B BX(X=0) 06H 00H~7F DECK 1
I C LOW 0B BX(X=0) 07H 00H~7F DECK 1
I C FILTER 0B BX(X=0) 08H 00H~7F DECK 1
C CH 0B BX(X=0) 09H 00H~7F
I DECK 1
FADER
I A HI 0B BX(X=0) 0AH 00H~7F DECK 1
I A MID 0B BX(X=0) 0BH 00H~7F DECK 1
I A LOW 0B BX(X=0) 0CH 00H~7F DECK 1
I A FILTER 0B BX(X=0) 0DH 00H~7F DECK 1
A CH 0B BX(X=0) 0EH 00H~7F
I DECK 1
FADER
I B HI 0B BX(X=0) 0FH 00H~7F DECK 1
I B MID 0B BX(X=0) 10H 00H~7F DECK 1
I B LOW 0B BX(X=0) 11H 00H~7F DECK 1
I B FILTER 0B BX(X=0) 12H 00H~7F DECK 1
B CH 0B BX(X=0) 13H 00H~7F
I DECK 1
FADER
I D HI 0B BX(X=0) 14H 00H~7F DECK 1
I D MID 0B BX(X=0) 15H 00H~7F DECK 1
I D LOW 0B BX(X=0) 16H 00H~7F DECK 1
I D FILTER 0B BX(X=0) 17H 00H~7F DECK 1

9
MIDI MAP (HEXADECIMAL)

CHANNEL
MIDI
I/O FUNCTION + FUNCTION CODE ACTION
CODE
MIDI CODE
D CH 0B BX(X=0) 18H 00H~7F
I DECK 1
FADER
CROSS 0B BX(X=0) 19H 00H~7F
I DECK 1
FADER
I MASTER 0B BX(X=0) 1AH 00H~7F DECK 1
I BOOTH 0B BX(X=0) 1BH 00H~7F DECK 1
I CUE MIX 0B BX(X=0) 1DH 00H~7F DECK 1
I CF CURVE 0B BX(X=0) 1EH 00H~7F DECK 1
LED
DECK 1
O S1 PLAY 09 9X (X=0) 22H 7FH：ON／00H：OFF
DECK 1
O S2 PLAY 09 9X (X=0) 23H 7FH：ON／00H：OFF
DECK 1
O S3 PLAY 09 9X (X=0) 24H 7FH：ON／00H：OFF
DECK 1
O S4 PLAY 09 9X (X=0) 25H 7FH：ON／00H：OFF
DECK 1
O CUE C 09 9X (X=0) 26H 7FH：ON／00H：OFF
DECK 1
O CUE A 09 9X (X=0) 27H 7FH：ON／00H：OFF
CUE B 09 28H DECK 1
O 9X (X=0) 7FH：ON／00H：OFF
CUE D 09 29H DECK 1
O 9X (X=0) 7FH：ON／00H：OFF
DECK 1
O C PEAK 09 9X (X=0) 2EH 7FH：ON／00H：OFF
DECK 1
O A PEAK 09 9X (X=0) 2FH 7FH：ON／00H：OFF
B PEAK 09 30H DECK 1
O 9X (X=0) 7FH：ON／00H：OFF
D PEAK 09 31H DECK 1
O 9X (X=0) 7FH：ON／00H：OFF
VINYL 9X(X=1,3) DECK A/C
O 09 01H 7FH：ON／00H：OFF
MODE 9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O IN 09 02H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O OUT 09 03H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O RE 09 04H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O SYNC 09 05H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O 1 09 06H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O 2 09 07H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O 3 09 08H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O 4 09 09H 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O CUP 09 0AH 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O CUE 09 0BH 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D
9X(X=1,3) DECK A/C
O 09 0CH 7FH：ON／00H：OFF
9X(X=2,4) DECK B/D

10
MIDI MAP (HEXADECIMAL)

CHANNEL
MIDI
I/O FUNCTION + FUNCTION CODE ACTION
CODE
MIDI CODE
LEVEL LED
20H DECK 1
LFET
O LEVEL LED 0B BX(X=0) 00H~7F＊
21H DECK 1
RIGHT

*LEVEL LED CODE：(CC COMMAND)

00~20  ALL LED OFF
21~41  1 LED ON
42~62  2 LEDS ON
63~83  3 LEDS ON
．．．．．
105~119  5 LEDS ON
126~127  ALL LEDS ON

11
12