Scribd Logo
Upload

Welcome to Scribd!

  • 12 views

    Model 720A: Pressure Vacuum Breaker Assembly

    Uploaded by

    Eric Burgler

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Model 720A: Pressure Vacuum Breaker Assembly

    Uploaded by

    Eric Burgler
    12 views2 pages

    Original Title

    BF-720A

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    12 views2 pages

    Model 720A: Pressure Vacuum Breaker Assembly

    Uploaded by

    Eric Burgler

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Model 720A

    Pressure Vacuum Breaker Assembly


    Application
    Designed for installation on irrigation water lines to protect
    against backsiphonage of contaminated water into the po-
    table water supply. Assembly shall provide protection where
    a potential health hazard exists. For non-potable applications
    only.

    Standards Compliance
    • ASSE® Listed 1020
    • UPC® Listed
    • CSA® Certified B64.1.2
    • Approved by the Foundation for Cross-Connection Control
    and Hydraulic Research at the University of Southern
    California

    Materials
    Main valve body Cast Bronze ASTM B584
    Fasteners Stainless Steel, 300 Series
    Elastomers Silicone
    Buna Nitrile
    Polymers Polypropylene Accessories
    POM Acetal (Delrin®) Repair kit (complete)
    Springs Stainless Steel, 300 series Water Hammer Arrester (Model 1260XL)
    QT-SET Quick Test Fitting Set
    Features
    Sizes: 1/2", 3/4", 1", 1 1/4", 1 1/2", 2"
    Maximum working water pressure 150 PSI
    Maximum working water temperature 110°F
    Hydrostatic test pressure 300 PSI
    End connections threaded ANSI B1.20.1

    D B

    A
    C

    Dimensions & Weights (do not include pkg.)


    DIMENSIONS (approximate) WEIGHT
    MODEL SIZE
    A B C D LESS BV WITH BV
    in. mm in. mm in. mm in. mm in. mm lbs. kg lbs. kg
    1/2 15 7 1/8 181 4 1/16 103 4 1/4 108 2 1/4 57 1.8 0.8 3.8 1.4
    3/4 20 7 3/16 183 4 5/16 110 4 5/16 110 2 3/8 60 1.8 0.8 3.8 1.4
    1 25 7 3/4 197 4 5/8 117 4 3/4 121 2 5/8 67 1.8 0.8 5.1 2.3
    1 1/4 32 11 279 7 7/16 189 7 7/16 189 3 1/8 79 14 6.4 20 9
    1 1/2 40 10 1/2 267 7 178 7 178 3 1/8 79 14 6.4 20 9
    2 50 11 1/16 281 7 9/16 192 7 11/16 195 3 1/8 79 14 6.4 26 10.4

    Zurn Industries, LLC | Wilkins Rev. G


    1747 Commerce Way, Paso Robles, CA U.S.A. 93446 Ph. 855-663-9876, Fax 805-238-5766 Date: 9/23
    In Canada | Zurn Industries Limited Document No. BF-720A
    7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, 877-892-5216 Product No. Model 720A
    Patent zurn.com/patents
    www.zurn.com
    Page 1 of 2
    Flow Characteristics ⃟ Rated Flow (established by approval agencies)

    MODEL 720A 1/2", 3/4", 1", 1 1/4", 1 1/2" & 2" (STANDARD & METRIC)
    PRESSURE LOSS (PSIG) FLOW RATES (l/s)
    0.63 1.26 1.89 2.52 3.2 3.8 2.52 5.0 7.6 10.1 12.6

    PRESSURE LOSS (kpa)


    10 10 69
    3/4" (20mm) 1 1/4" (32mm) 1 1/2" (40mm)
    1/2" (15mm)

    1" (25mm)
    5 5 2" (50mm) 35

    0 0
    0 10 20 30 40 50 60 0 40 80 120 160 200
    FLOW RATES (GPM)
    Rated Flow (Established by approval agencies)

    Typical Installation Capacity thru Schedule 40 Pipe


    Local codes shall govern installation requirements. Unless
    otherwise specified, the assembly shall be mounted at a Pipe size 5 ft/sec 7.5 ft/sec 10 ft/sec 15 ft/sec
    minimum of 12" (305mm) above the highest piping or outlet 1/8" 1 1 2 3
    downstream of the device. Install with adequate drain and 1/4" 2 2 3 5
    sufficient side clearance for testing and maintenance. The
    installation shall be made so that no part of the unit can be 3/8" 3 4 6 9
    submerged. A pressure vacuum breaker cannot be installed 1/2 5 7 9 14
    where back-pressure could occur or where spillage of water 3/4" 8 12 17 25
    from vent could cause damage. 1" 13 20 27 40
    1 1/4" 23 35 47 70
    1 1/2" 32 48 63 95
    2" 52 78 105 167

    12" MIN. ABOVE


    HIGHEST PIPING

    TESTCOCKS (4)
    1” 720A PVB
    (25MM)

    OUTLET SHUT OFF


    VALVE (5)

    OUTLET DRAIN
    DIRECTION OF FLOW VALVE (6)

    INDOOR INSTALLATION
    INLET
    MAIN SHUT-OFF TO IRRIGATION
    SHUT OFF
    VALVE (1) SYSTEM
    VALVE (3)

    12" MIN. ABOVE


    HIGHEST OUTLET INLET DRAIN
    VALVE (2)
    (If allowed by
    local codes)

    DRAIN

    DIRECTION OF FLOW

    DIRECTION OF FLOW
    TYPICAL OUTDOOR INSTALLATION
    TYPICAL OUTDOOR INSTALLATION For cold climates which require winterization
    For warm climates with no winterization
    Specifications
    The Pressure Vacuum Breaker shall be ASSE 1020 approved, and supplied with full port ball valves. The main body and bon-
    net shall be bronze (ASTM B584), the loaded-air inlet shall use an silicone elastomer spring and seat disc. The entire assem-
    bly shall be accessible for maintenance and testing without removing the device from the line. For non-potable applications
    only. The Pressure Vacuum Breaker shall be a Zurn Wilkins Model 720A.

    Zurn Industries, LLC | Wilkins


    1747 Commerce Way, Paso Robles, CA U.S.A. 93446 Ph. 855-663-9876, Fax 805-238-5766
    In Canada | Zurn Industries Limited
    7900 Goreway Drive, Unit 10, Brampton, Ontario L6T 5W6, 877-892-5216
    www.zurn.com
    Page 2 of 2

    You might also like