8030

INLINE flowmeter for

continuous flow measurement

• Economic integration in pipe systems without any

additional piping
• 3-wire frequency pulse version to directly interface
with PLC’s (both PNP and NPN)
• Connection to Bürkert devices in remote versions
Type 8030 can be combined with...

Type 8025 Type 8611 Type 8802-GD Type 8619 PLC

Flow transmitter Universal Controller Continuous multiCELL

eControl TopControl system Transmitter/Controller

The paddle wheel flowmeter for continuous

General data
flow measurement is especially designed for
Compatibility With fittings S030 (see corresponding data sheet)
use in neutral, slightly aggressive, solid free
liquids. Materials
Housing, cover, male fixed connector PC
Cable plug / seal / screws PA / NBR / Stainless steel
The flowmeter is made up of a compact fitting
Wetted parts materials
(S030) and an electronic module (SE30) quickly
Fitting, sensor armature Brass, stainless steel 1.4404/316L,
and easily connected together by a Quarter- PVC, PP, PVDF
Turn. The Bürkert designed fitting system en- Paddle wheel PVDF
sures simple installation of the devices into all Axis, bearing / Seal Ceramics / FKM or EPDM (depending on Sensor-Fitting version)
pipes from DN06 to DN65. The flowmeter pro- Electrical connection Cable plug EN 175301-803 (Type 2508)
duces a frequency signal, proportional to the Connection cable max. 1.5 mm2 cross section; max. 50 m length, shielded
flow rate, which can easily be transmitted and
processed by a Bürkert transmitter/controller. Complete device data (fitting + electronic module)
Pipe diameter DN06 to DN65
Measuring range 0.3 to 10 m/s
Medium temperature with fitting in
PVC / PP 0 to 50°C (32 to 122°F) / 0 to 80°C (32 to 176°F)
Stainless steel, brass, PVDF -15 to 100°C (5 to 212°F)
Medium pressure max. PN10 (with plastic fitting) PN16 (with metal fitting)
(PN40 on request, see S030 data sheet)
Viscosity / Pollution 300 cSt. max. / max. 1% (Size of particles 0.5 mm max.)
Measurement error
Teach-In ±1% of Reading1) (at the teach flow rate value)
Standard K-factor ±2.5% of Reading1)
Linearity ±0.5% of F.S.*1)
Repeatability ±0.4% of Reading1)

Environment
Ambient temperature -15 to + 60°C (5 to 140°F) (operating and storage)
Relative humidity  80%, without condensation
* F.S. = Full scale (10 m/s)
1)
Under reference conditions i.e. measuring fluid = water, ambient and water temperature = 20°C (68°F), applying the
minimum inlet and outlet pipe straights, matched inside pipe dimensions.

www.burkert.com p. 1/5
 8030

Electrical data
Operating voltage 12 - 36 V DC filtered and regulated (via Bürkert transmitter
the device is connected for “Low Power” version)
Current consumption with sensor
Hall version  30 mA
Hall “Low power” version  0.8 mA
Output: Frequency
Hall version 2 transistors NPN and PNP, open collector, max. 100 mA,
frequency: 0... 300 Hz; duty cycle 1/2 ±10%
NPN output: 0,2-36 VDC
PNP output: supply voltage
Hall “Low Power” version 1 transistor NPN, open collector, max. 10 mA,
frequency: 0... 300 Hz; duty cycle 1/2 ±10%
Dielectric strengh 2300 V AC
Reversed polarity of DC Protected * For the 97/23/CE pressure directive, the device can
only be used under following conditions (dependent on
Standards and approvals max. pressure, pipe diameter and fluid).
Protection class IP65 with connector plugged-in and tightened Type of fluid Conditions
Standard and directives Fluid group 1, §1.3.a DN 25 only
EMC EN 61000-6-2, 61000-6-3 Fluid group 2, §1.3.a DN 32 or
Pressure Complying with article 3 of §3 from 97/23/CE directive.* DN > 32 and PN*DN 1000
Vibration EN 60068-2-6 Fluid group 1, §1.3.b PN*DN 2000
Shock EN 60068-2-27 Fluid group 2, §1.3.b DN 200

Pressure/temperature chart

0ÖBAR !

 -ETAL





 06$&

06#Ö Ö00 06$&Ö0.



 06#Ö0.


 00Ö0.
 4ÖÊ#
       

A: Application range for complete device (fitting + flowmeter)

p. 2/5
 8030

Design and principle of operation

The flowmeter 8030 is built up with an electronic module SE30 associated to a fitting S030 with integrated measurement paddle wheel. This connec-
tion is made by means of a Quarter-Turn.
In a 3-wire system, the signal can be displayed or processed directly. The output signal is provided via cable plug according to EN 175301-803.

When liquid flows through the pipe, the paddle-wheel is set in rotation. The non-wetted permanent magnets inserted in the paddle wheel generate a
measuring signal which frequency is proportional to the flow velocity. A conversion coefficient (K-factor, available in the instruction manual of the fitting), specific
to each pipe (size and material) enables the conversion of this frequency into flow rate.

Two electronic module versions with frequency output are available:

- with two transistor outputs NPN and PNP. - with one NPN transistor “Low Power” output.
An external power supply of 12 - 36 V DC is required. It is designed for An external power supply of 12 - 36 V DC is required. Can only be con-
connection to any system with open collector NPN or PNP frequency nected to remote versions of flow transmitters Type 8025/8032.
input.

Installation

The 8030 flowmeter can easily be installed into any Bürkert INLINE fitting system Type S030, by means of a Quarter-
Turn. Minimum straight upstream and downstream distances must be observed. According to the pipe’s design, neces-
sary distances can be bigger or use a flow conditioner to obtain the best accuracy. For more information, please refer to
EN ISO 5167-1.
EN ISO 5167-1 prescribes the straight inlet and outlet distances that must be complied with when installing fittings in
pipe lines in order to achieve calm flow conditions. The most important layouts that could lead to turbulence in the flow are
shown below, together with the associated prescribed minimum inlet and outlet distances. These ensure calm, problem-free
measurement conditions at the measurement point.

DN = pipe diameter Flow direction -->

Pipe diameter
Control valve 2 x 90° elbow joint
expansion

ÖXÖ$. ÖXÖ$. ÖXÖ$. ÖXÖ$. ÖXÖ$. ÖXÖ$.

2 x 90° elbow joint 90° elbow joint Pipe diameter

3 dimensional or T-piece reduction

ÖXÖ$. ÖXÖ$. ÖXÖ$. ÖXÖ$. ÖXÖ$. ÖXÖ$.

The device can be installed into either horizontal or vertical pipes.

Correct Incorrect FLOW

FLOW

Incorrect FLOW FLOW

FLOW
WOLF

Correct Incorrect
FLOW

Correct
Incorrect
Correct FLOW

Pressure and temperature ratings must be respected according to the selected fitting material. The suitable pipe size is selected using the diagram
Flow/Velocity/DN. The measuring device is not designed for gas flow measurement.

p. 3/5
 8030

Diagram Flow/Velocity/DN Dimensions

Example:

• Flow: 10 m3/h
• Ideal flow velocity: 2...3 m/s
For these specifications, the diagram indicates a pipe size of DN40 [or DN50 for (*) men-
tioned fittings]





Flow rate of fluid
Not recommended
gpm m3/h
1000 l/min


3000 200
500 2000 DN65
100
DN50 (DN65)* 
1000
200 50 DN40 (DN50)*
500 DN32 (DN40)*
100
20 DN25 (DN32)*
50 200 DN20 (DN25)*
10

100 DN15 (DN15 or

20 5 DN20)*

(
50
10
2 DN08

5 20
1 DN06
10
2 0.5
DN H
5 [mm] [mm]
1
0.2 06 95.5
0.5 2 08 95.5
0.1
15 100.5
1
0.2 0.05 20 98.0
0.5 25 98.0
0.1
0.02 32 102.0
0.05 0.2 40 105.5
0.01
50 112.0
0.1 0.3 0.5 1 3 5 10m/s Flow
0.3 0.5 1 3 5 10 30 fps velocity
65 112.0

* for following fitings with:

• external threads acc. to SMS 1145
• weld ends acc. to SMS 3008, BS 4825/ASME BPE or DIN 11850 Series 2
• Clamp acc. to SMS 3017/ISO 2852, BS 4825/ASME BPE or DIN 32676

p. 4/5
 8030

Ordering chart for flowmeter Type 8030

A flowmeter Type 8030 consists of: - an electronic module Type SE30

- an INLINE fitting Type S030 (DN06 to DN65 - Refer to corresponding data sheet)

Description

connection
Electrical

Item no.
Voltage

Output
supply
Hall version flowmeter (pluggable to Types 12 - 36 V DC Frequency, 2 transistors NPN and Cable plug EN 175301-803 423 913
8025 Universal transmitter, batch controller or PNP
konti-Dos; 8032; 8619; PLC)
Hall “Low Power” version flowmeter from associated Frequency, 1 transistor NPN Cable plug EN 175301-803 423 914
(pluggable to Types 8025, 8032 transmitter) transmitter

Ordering chart for accessories (has to be ordered separately)

Specifica-

Item no.
tions

Cable plug EN 175301-803 with cable gland (Type 2508) 438 811
Cable plug EN 175301-803 with NPT1/2 “ reduction without cable gland (Type 2509) 162 673

Interconnection possibilities with other Bürkert products

Type 8025 - Type 8032 - Type 8025 - Type 8032 -

Universal, konti-Dos Flow switch/transmitter Flow transmitter Flow switch/transmitter
flow transmitter/batch
controller

PLC

Type 8030 - Type 8030 -

Flowmeter with Flowmeter with
Hall transducer Hall “Low Power”
(NPN and PNP tran- transducer
sistor outputs) (NPN output)

To find your nearest Bürkert office, click on the orange box www.burkert.com

In case of special application conditions, Subject to alteration.

please consult for advice. © Christian Bürkert GmbH & Co. KG 1401/14_EU-en_00891778

p. 5/5