Manual Configuracao Honeywell Eclipse Ms 5145
Manual Configuracao Honeywell Eclipse Ms 5145
Manual Configuracao Honeywell Eclipse Ms 5145
bztech.com.br
MetroSelect®
Single-Line Scanner
Configuration Guide
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether any
such changes have been made. The information in this publication does not
represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein: nor for incidental or consequential damages resulting from the
furnishing, performance, or use of this manual.
Trademarks
Omniplanar, MetroSet2, Metrologic, MetroSelect, RangeGate, CodeGate,
CodeSelect, Voyager, VoyagerCG, VoyagerBT and Focus are trademarks or
registered trademarks of Metrologic Instruments, Inc. or Honeywell
International Inc.
The Bluetooth word mark is owned by the Bluetooth SIG, Inc. and any use of
such marks by Honeywell International Inc. is under license.
iii
Scanner Operation
Configuration Mode Options ...................................................................... 7–1
Scan Buffers .............................................................................................. 7–1
Redundant Scans ...................................................................................... 7–2
Miscellaneous Decode Features ............................................................... 7–2
Same Symbol Timeouts ............................................................................ 7–3
LED Options .............................................................................................. 7–3
Beeper Options ......................................................................................... 7–4
Data Transmission Delays......................................................................... 7–6
Communication Timeout Options .............................................................. 7–7
Host Scanner Commands ......................................................................... 7–8
Test Modes.............................................................................................. 7–10
Prefixes/Suffixes
User Configurable Prefixes, All Data ......................................................... 8–1
User Configurable ID Characters, Code Specific ...................................... 8–2
Standard Prefix Characters ....................................................................... 8–4
Standard Suffix Characters ....................................................................... 8–6
Longitudinal Redundancy Check ............................................................... 8–7
Block Check Character .............................................................................. 8–7
Character Replacements ........................................................................... 8–8
User Configurable Suffixes, All Data ......................................................... 8–9
Special Formats ...................................................................................... 8–10
Code Formatting
UPC/EAN Formatting ................................................................................ 9–1
Codabar Formatting .................................................................................. 9–3
Code 39 Formatting................................................................................... 9–4
Code 11 Formatting................................................................................... 9–4
Telepen ..................................................................................................... 9–4
Plessey ...................................................................................................... 9–5
2 of 5 Code Formatting .............................................................................. 9–5
iv
RS232
Parity Features ....................................................................................... 10–1
Baud Rate ............................................................................................... 10–1
Data/Stop Bits ......................................................................................... 10–2
Hardware Handshaking .......................................................................... 10–2
Software Handshaking ............................................................................ 10–4
Miscellaneous ......................................................................................... 10–5
Keyboard
Enable Keyboard Emulation ................................................................... 11–1
Country/Scan Code Table Selects .......................................................... 11–1
Keyboard/System Type........................................................................... 11–2
’Dumb’ Terminal Selections .................................................................... 11–3
Special Keyboard Features..................................................................... 11–4
InterScan Code Delays ........................................................................... 11–6
Control Sets ............................................................................................ 11–7
RS485 Configuration
IBM Port .................................................................................................. 14–1
IBM Reserve Codes ................................................................................ 14–1
USB.................................................................................................. 15–1
v
® ®
MS9520 Voyager and MS9540 VoyagerCG Series
Activation Range ..................................................................................... 17–1
Stand Scan Modes .................................................................................. 17–1
CodeGate® Status .................................................................................. 17–1
Laser/Scan Modes .................................................................................. 17–2
Same Symbol Time Outs......................................................................... 17–3
MS9520/9540-00 Laser Emulation Mode ................................................ 17–4
®
MS9524 and MS9544 VoyagerPDF Series
PDF CodeGate Status ............................................................................. 18–1
MicroPDF and Composite Code Handling ............................................... 18–1
Miscellaneous Features
Custom Defaults ...................................................................................... 23–1
Serial Program Mode .............................................................................. 23–2
vi
1
Introduction
Your new scanner has been factory configured with a set of default
parameters. Since many host systems have unique formats and protocol
requirements, Honeywell provides a wide range of configurable features
that may be selected using this bar code based configuration tool. Once the
configuration is completed, the scanner stores the settings in nonvolatile
memory (NOVRAM). NOVRAM saves the settings when the power is off.
Note: Bar code descriptions marked with an asterisk ( * ) define a feature that
is a factory default. Bar codes marked with a tilde ( ~ ) require the
Multi-Code configuration method.
Single-Code Method
Most features can be enabled or disabled using the Single-Code Method.
1. Power-up the scanner.
2. Scan the bar code for the desired feature.
3. The scanner will emit a multi-toned beep to indicate the configuration
has been saved to NOVRAM.
Multi-Code Method
All features can be enabled or disabled using the Multi-Code Method.
A feature marked with a tilde ( ~ ) requires the Multi-Code Method.
1. Power-up the scanner.
2. Scan the enter/exit configuration mode bar code (3 beeps).
3. Scan the bar code for the desired feature (1 beep). Multiple features
can be enabled/disabled before scanning the enter/exit configuration
mode bar code.
4. Scan the enter/exit configuration mode bar code (3 beeps) and save
the new configuration. To abort a configuration change, power off the
scanner before scanning the enter/exit code.
³ 9 9 9 9 9 9
1–1
Need To Start Over?
Scan the Recall Defaults bar code to erase all previous settings and return
the scanner to its factory default communication protocol. Keyboard Wedge
interface scanners will load keyboard wedge defaults. All other scanners load
RS232 defaults.
Recall Defaults
³ 9 9 9 9 9 8
1–2
2
Code Types and Decode Rules
Bar code descriptions marked with an asterisk ( * ) define a feature that is a
factory default. Bar codes marked with a tilde ( ~ ) require the Multi-Code
configuration method.
UPC/EAN
* Enable UPC/EAN
³ 1 0 0 1 1 6
Disable UPC/EAN
³ 1 0 0 1 0 6
* Enable UPC-A
³ 1 0 0 2 1 6
Disable UPC-A
³ 1 0 0 2 0 6
* Enable UPC-E
³ 1 0 0 2 1 0
Disable UPC-E
³ 1 0 0 2 0 0
* Enable EAN-13
³ 1 0 0 2 1 1
Disable EAN-13
³ 1 0 0 2 0 1
* Enable EAN-8
³ 1 0 0 2 1 4
Disable EAN-8
³ 1 0 0 2 0 4
2–1
Code 128
* Enable Code 128
³ 1 0 0 1 1 3
Code 39
* Enable Code 39
³ 1 0 0 1 1 1
Disable Code 39
³ 1 0 0 1 0 1
2–2
Enable PARAF (Italian Pharmaceutical Codes)
³ 1 0 0 2 1 5 Support – Code 39 bar codes are converted to
PARAF format.
2–3
Enable Alternate Code 39 Reference
³ 1 1 5 4 1 3 Comparison Check – assists with elements that
are below the 2 to 1 (wide to narrow) element
width requirement.
* Normal Code 39 Reference Comparison
³ 1 1 5 4 0 3 Check
2 OF 5 CODES
* Enable Interleaved 2 of 5 (ITF)
³ 1 0 0 1 1 5
2–4
Alternative ITF first Bar Reference
³ 1 0 0 9 1 3
Enable Standard 2 of 5
³ 1 0 0 1 1 0
* Disable Standard 2 of 5
³ 1 0 0 1 0 0
Enable Matrix 2 of 5
³ 1 0 0 0 1 5
* Disable Matrix 2 of 5
³ 1 0 0 0 0 5
2–5
Enable Hong Kong 2 of 5
³ 1 0 0 3 1 6
Codabar
* Enable Codabar
³ 1 0 0 1 1 4
Disable Codabar
³ 1 0 0 1 0 4
Code 93
* Enable Code 93
³ 1 0 0 1 1 2
Disable Code 93
³ 1 0 0 1 0 2
Code 11
Enable Code 11
³ 1 0 0 0 1 3
2–6
* Disable Code 11
³ 1 0 0 0 0 3
Telepen
Enable Telepen
³ 1 0 0 0 1 7
* Disable Telepen
³ 1 0 0 0 0 7
Plessey Codes
Enable MSI Plessey
³ 1 0 0 2 1 2
2–7
Enable MSI Plessey MOD 10/10 Check Digit –
³ 2 0 0 7 3 4 Test MSI Plessey bar codes for a 2 digit
Modulo 10 check digit.
Enable UK Plessey
³ 1 0 0 1 1 7
* Disable UK Plessey
³ 1 0 0 1 0 7
2–8
~ Minimum Symbol Length – Single-line default
³ 9 0 1 8 0 0 is 3. Combine this code with the proper code bytes
(on page 16–1), to specify the minimum number
of characters in all non-UPC/EAN bar codes.
2–9
~ Code Length Lock #2
³ 9 0 2 2 0 0
2–10
3
Supplements
Enable Two Digit Supplements
³ 1 0 1 2 1 7
3–1
Enable Bookland (978) Supplement Required
³ 1 0 1 4 1 7
3–2
* Enable 2 Digit Supplements with 37x, 43x, or
³ 1 0 1 0 0 0 UPC # System 5
3–3
Enable Code ID’s with Supplements
³ 1 0 1 2 1 4
3–4
Disable Supplemental when CodeGate Button
³ 1 0 1 2 1 0 is Pressed – Available for MS9540 scanners
only. Requires standard Code Gate be inactive in
and out of stand.
3–5
3–6
4
GS1 DataBar
® ®
Honeywell’s MS9520 Voyager and MS9540 VoyagerCG scanners with
software #14810 and higher can be configured to scan GS1 DataBar type
bar codes.
4–1
GS1 DataBar Limited
Enable GS1 DataBar Limited
³ 1 0 0 4 1 4
4–2
5
ISBT Code 128 Implementation
Configuration Mode
Enable ISBT Code 128
³ 1 3 8 4 1 7
The bar codes below enable or disable a special transmit mode as outlined in
section 3.5.2 of the ISBT-128 Specification. This output method allows the user
to confirm independently the accuracy of the Code-128 check digit.
The bar codes below enable or disable the transmission of the ISBT Code 128
data identifiers. When this option is enabled, the first two data characters
are removed from the data stream (ID characters) unless the ISBT bar code
scanned contains Donation Identification Number identifiers. If Donation
Identification Number identifiers are present, only the first ID character is
removed from the Donation ID Number. The second is regarded as
normal data.
The bar codes below convert and transmit the Mode 37, 2 check digit from the
flag digits of the Donation Identification Number provided the check digit is
contained in the flag digits. Transmission of the Donation Identification number
will be the same except for the last two digits, which are converted into a single
check sum character.
5–1
†
Concatenation Configuration Mode
The following bar codes are used to configure variable time requirements used
to find the second bar code of the ISBT concatenation sequence.
5–2
Donation Identification Number + Donor
³ 4 3 8 4 9 0 Identification Number =á + &; Concatenation
st
1 Left Identifier
³ 9 3 8 0 0 0
nd
2 Left Identifier
³ 9 3 8 1 0 0
st
1 Right Identifier
³ 9 3 8 2 0 0
nd
2 Right Identifier
³ 9 3 8 3 0 0
5–3
The following example demonstrates how to configure the User-Defined ISBT
identifiers:
= & ³ = G & a 5 0 5 d 1
= & ³ = G & a 5 0 5 d 0
Two forms of concatenation can be enabled at any given time, one pre-defined
sequence and the user-defined sequence. Code selects and ISBT Code-128
concatenation cannot be used simultaneously. Both functions use the same
internal resources so they must remain mutually exclusive.
5–4
6
Communications
Enable Light Pen/Wand Communication –
³ 4 1 5 5 2 4 Use this option if scanner should be used in
place of a light pen.
* Enable RS232 – The scanner will work with
³ 4 1 5 5 5 4 RS232 +/- 12V serial output.
Reserved
³ 9 1 7 5 0 0
Reserved
³ 4 1 5 5 6 4
®
† Applicable for IBM Host applications.
6–1
6–2
7
Scanner Operation
Configuration Mode Options
Allow Configuration Mode on Power Up – The
³ 1 1 8 1 1 7 scanner can only enter MetroSet mode before
any bar codes are scanned.
* Allow Configuration Mode Anytime – Allow
³ 1 1 8 1 0 7 MetroSet configuration at any time.
Scan Buffers
* 1 Scan Buffer – The scanner will scan one bar
³ 3 1 8 0 0 0 code in the scan field and not scan again until
the bar code is removed from the scan field for
the duration of the same symbol time out.
7–1
Redundant Scans
* 0 Redundant Scans – Requires 1 good decode
³ 3 0 1 1 0 0 for a good scan.
7–2
Same Symbol Time Outs
The length of time before a bar code can be rescanned after it is removed from
the scan field is user-configurable in increments of 50 msecs to 6350 msecs
(6.35 sec).
LED Options
Flash Green LED if Rescan Allowed – This
³ 1 1 8 3 1 3 indicates same symbol timeout has elapsed.
7–3
Beeper Options
* Normal Tone
³ 3 1 8 5 7 5
Optional Tone 1
³ 3 1 8 5 6 5
Optional Tone 2
³ 3 1 8 5 5 5
Optional Tone 3
³ 3 1 8 5 4 5
Optional Tone 4
³ 3 1 8 5 3 5
Optional Tone 5
³ 3 1 8 5 2 5
Optional Tone 6
³ 3 1 8 5 1 5
No Beep
³ 3 1 8 5 0 5
7–4
Beep on BEL Command – The scanner beeps
³ 1 1 8 4 1 7 when it receives a BEL character from the host. If
a number is sent within 200 msecs before the
BEL character, the scanner will beep that
number of times.
Enable Pass-Through
³ 1 2 4 7 1 1
Disable Pass-Through
³ 1 2 4 7 0 1
7–5
Data Transmission Delays
Use these codes to select the amount of delay between sending data
characters from the scanner to the host. This helps prevent the scanner from
overflowing host-input buffers.
No Intercharacter Delay
³ 8 1 8 8 0 0
7–6
Communication Time Out Options
Enable Communications Time Out
³ 1 1 8 4 1 2
7–7
Host Scanner Commands
Enable D/E Disable Command – The scanner
³ 1 1 8 0 1 5 will disable scanning after it receives an ASCII
“D” from the host device. It will enable scanning
when it receives an ASCII “E”.
* Disable D/E Disable.
³ 1 1 8 0 0 5
7–8
Transmit Scanner ID byte with receipt of an
³ 1 1 5 9 1 6 “i” (69H) via RS232 – The ID byte is transmitted
as 3 bytes (i.e. 0, 0, 1).
7–9
Use Protocol Prefix and Suffix for Bar Code
³ 1 4 1 7 1 5 Transmission
Test Modes
Scan Count Mode ON – The scanner will enter
³ 1 1 8 0 1 6 scan count test mode and the scanner’s firmware
number will transmit to the host. Do not enable
unless instructed by a Honeywell representative.
7–10
8
Prefixes/Suffixes
Scan the Enter Configuration Mode bar code before trying to set these features
(see the Multi-Code Method on page 1–1).
8–1
User Configurable ID Characters, Code Specific
* Use Configurable Code ID Bytes as Prefixes –
³ 1 0 5 5 0 7 User configured, code specific ID bytes are
transmitted before the data. If using prefixes,
user configured suffixes cannot be used.
‡ Enter configuration mode then scan this bar code followed by the three
code byte bar codes (on page 16–1) that represent a unique ID character to
be associated with this bar code type.
~ Configurable UPC-A ID ‡
³ 9 0 5 6 0 0
~ Configurable UPC-E ID ‡
³ 9 0 5 7 0 0
~ Configurable EAN-8 ID ‡
³ 9 0 5 8 0 0
~ Configurable EAN-13 ID ‡
³ 9 0 5 9 0 0
~ Configurable Code 39 ID ‡
³ 9 0 6 0 0 0
~ Configurable Code 93 ID ‡
³ 9 0 6 3 0 0
~ Configurable Code 11 ID ‡
³ 9 0 6 4 0 0
~ Configurable Telepen ID ‡
³ 9 0 6 2 0 0
8–2
‡ Enter configuration mode then scan this bar code followed by the three
code byte bar codes (on page 16–1) that represent a unique ID character
to be associated with this bar code type.
~ Configurable TRI-OPTIC ID ‡
³ 9 0 7 2 0 0
~ Configurable Standard 2 of 5 ID ‡
³ 9 0 7 1 0 0
~ Configurable Interleaved 2 of 5 ID ‡
³ 9 0 6 7 0 0
~ Configurable Matrix 2 of 5 ID ‡
³ 9 0 6 8 0 0
~ Configurable Airline 2 of 5 ID ‡
³ 9 0 6 9 0 0
~ Configurable UK Plessey ID ‡
³ 9 0 7 0 0 0
~ Configurable Codabar ID ‡
³ 9 0 6 6 0 0
Enable Teraoka ID
³ 1 0 5 5 1 6
* Disable Teraoka ID
³ 1 0 5 5 0 6
8–3
Standard Prefix Characters
Enable STX Prefix – The scanner will transmit a
³ 1 1 6 6 1 5 Start of TeXt (ASCII 02H) before each bar code.
8–4
Enable SANYO ID Characters
³ 1 0 7 9 1 6
8–5
Enable Tec 7-11 IDs
³ 1 2 4 6 1 0
Disable CR Suffix.
³ 1 1 6 6 0 3
Disable LF Suffix.
³ 1 1 6 6 0 2
8–6
Enable NCR Suffix Character
³ 9 4 1 6 0 0
The result, an “LRC byte” is then transmitted following the data stream and
used by the receiving computer to determine if the information was received
correctly. In the scanner’s case, XOR is performed prior to adding parity bits.
When the LRC is enabled, the scanner defaults to starting the LRC on the
second byte of information transmitted. Optionally, the calculation can start on
the first byte transmitted.
8–7
Character Replacements
To replace a character:
1. Scan the enter/exit configuration mode bar code (on page 1–1).
2. Scan the character to replace code (shown below).
3. Scan the ASCII code byte value of the character you wish to replace.
Refer to the ASCII Reference Table in the Code Byte Usage section of
this manual.
4. Scan the replacement character bar code (shown below).
5. Scan the ASCII code byte value of the replacement character.
6. Scan the enter/exit configuration mode bar code (on page 1–1).
~ Character to Replace
³ 9 3 8 6 0 0
~ Replacement Character
³ 9 3 8 7 0 0
No Replacement
³ 8 3 8 6 0 0
8–8
User Configurable Suffixes, All Data
Note: Scan the Enter/Exit Configuration mode code before trying to set this
feature. Refer to Multi-Code Method on page 1–1.
8–9
Special Formats
Enable SINEKO Mode
³ 1 0 7 9 1 4
8–10
9
Code Formatting
UPC/EAN Formatting
* Transmit UPC-A Check Digit
³ 1 0 7 5 1 7
9–1
Transmit Lead Zero on UPC-E – This option will
³ 1 0 7 5 1 3 transmit a zero before each UPC-E bar code.
9–2
Codabar Formatting
Transmit Codabar Start/Stop Characters –
³ 1 0 7 7 1 7 Transmits Codabar’s Start/stop characters before
and after each bar code.
9–3
Code 39 Formatting
Transmit Mod 43 Check Digit on Code 39 –
³ 1 0 7 7 1 5 This feature works in conjunction with Mod 43
Check Digit on Code 39 option, on page 2–2.
Both must be enabled for this feature to work.
Code 11 Formatting
Transmit Code 11 Check Digit – This bar code
³ 1 0 7 7 1 3 will transmit Code 11 check characters when
used with Enabled Code 11 on page 2–6.
Telepen
Enable Convert Telepen ^L to E
³ 1 0 7 8 1 4
9–4
Plessey
Transmit UK Plessey Check Digit – The scanner
³ 1 0 7 8 1 6 will transmit UK Plessey Check Digit characters
and must be used with the UK Plessey option.
2 of 5 Code Formatting
Transmit Mod 10 Check Digit on ITF – The
³ 1 0 7 7 1 4 scanner transmits interleaved 2 of 5 (ITF) Mod 10
check character.
9–5
9–6
10
RS232
* Enable RS232 Mode – The scanner will work
³ 4 1 5 5 5 4 with RS232 +/-12V serial output.
Parity Features
A parity bit is an extra data bit used to help catch data transmission errors.
The scanner’s parity must match the host’s parity.
No Parity
³ 3 1 6 0 4 5
Baud Rate
115200 BAUD Rate
³ 4 1 5 8 1 0 0 (Not available with Voyager)
10–1
* 9600 BAUD Rate
³ 4 1 5 8 5 0
Data/Stop Bits
8 Data Bits – The number of data bits
³ 1 1 6 0 1 3 transmitted for each character.
* 7 Data Bits
³ 1 1 6 0 0 3
1 Stop Bit
³ 1 1 6 0 1 4
* 2 Stop Bits
³ 1 1 6 0 0 4
Hardware Handshaking
Enable RTS/CTS Handshaking – Output a
³ 1 1 5 8 1 6 Request to Send (RTS) signal and wait for a Clear
to Send (CTS) signal before transmitting data.
10–2
* Character RTS/CTS – Activates/Deactivates
³ 1 1 5 8 1 5 RTS signal for each character.
10–3
Enable RTS Counter Toggle – The scanner will
³ 1 1 5 9 1 5 toggle the RTS line on a good decode.
Software Handshaking
Enable ACK/NAK – After transmitting data, wait
³ 1 1 5 9 1 3 for an ACK (06H) or a NAK (15H) response from
the host. If ACK is received, complete the
communications cycle and look for more bar
codes. If NAK is received, retransmit the last set
of bar code data and wait for ACK/NAK again.
* Disable ACK/NAK
³ 1 1 5 9 0 3
10–4
Enable 5 NAK Retries
³ 1 1 5 8 1 4 Allow up to 5 retransmissions of the data if a
NAK is received.
Miscellaneous
Enable French PC Term – The scanner
³ 1 1 6 1 1 0 transmits PC type make/break scan codes
instead of ASCII data characters. The scan
codes match a WYSE French PC Term.
10–5
10–6
11
Keyboard
Enable Keyboard Emulation
Load Keyboard Wedge Defaults – Loads the
³ 9 9 9 9 9 4 default settings for keyboard wedge mode.
Switzerland Keyboard
³ 4 1 6 2 8 0
Spain Keyboard
³ 4 1 6 2 5 0
Italy Keyboard
³ 4 1 6 2 4 0
Germany Keyboard
³ 4 1 6 2 3 0
France Keyboard
³ 4 1 6 2 2 0
UK Keyboard
³ 4 1 6 2 1 0
11–1
Belgium Keyboard
³ 4 1 6 2 0 0
Japan Keyboard
³ 4 1 6 2 1 0 0
Sweden/Finland Keyboard
³ 4 1 6 2 9 0
Slovenian Keyboard
³ 4 1 6 2 1 1 0
Keyboard/System Type
* AT Keyboard – Includes IBM PS/2 and
³ 2 1 6 2 1 5 compatible models 50, 55, 60, 80.
11–2
‘Dumb’ Terminal Selections
Note: The following terminals may require custom cables.
IBM Terminal Keyboards
³ 3 1 6 4 0 0
11–3
Special Keyboard Features
Transmit Make Code Only – Not available on
³ 1 1 6 3 1 1 all models.
11–4
Enable Auto Detect Mode (AT/PS2) –
³ 1 1 6 2 1 4 Automatically detects caps lock status.
* Character KB Inhibit
³ 1 1 6 3 0 4
Message KB Inhibit
³ 1 1 6 3 1 4
11–5
Enable Right Alt Key Sequencing
³ 1 1 6 3 0 2
11–6
Control Sets
In general, standard bar code symbologies will only encode the ASCII
character set. Function keys, arrow keys and many other extended keys on an
IBM compatible keyboard do not translate to ASCII characters. One method of
‘bar coding’ the extended keys is to substitute the extended key codes when a
specific ASCII control character is found in the bar code stream. The Control
Sets are specific translations of the ASCII (HEX) set.
Control Set #1
Enable Control Set #1
³ 4 1 6 4 8 4
11–7
ASCII (HEX) ASCII Control Extended Key
00H Null Numeric Keypad + (Plus)
01H SOH Num Lock
02H STX Down Arrow
03H ETX Numeric Keypad - (Minus)
04H EOT Insert
05h ENQ Delete
06H ACK System Request
07H BEL (Right Arrow)
08H BS (Left Arrow)
09H TAB Tab
0AH LF Caps Lock
0BH VT Shift Tab
0CH FF Left Alt
0DH CR Enter
0EH SO Left Control
OFH SI Up Arrow
10H DLE F1
11H DC1 F2
12H DC2 F3
13H DC3 F4
14H DC4 F5
15H NAK F6
16H SYN F7
17H ETB F8
18H CAN F9
19H EM F10
1AH SUB Home
1BH ESC Esc
1CH FS Page Up
1DH GS Page Down
1EH RS Print Screen
1FH US End
11–8
12
OCIA
Enable OCIA Mode – Select this option if
³ 4 1 5 5 4 4 communications requires OCIA (Optically
Coupled Interface Adapter). The host clocks this
serial interface.
Enable DTS/Siemens
³ 2 1 7 7 0 6
* Enable DTS/Nixdorf
³ 2 1 7 7 1 6
Enable NCR-S
³ 2 1 7 7 3 6
Enable NCR-F
³ 2 1 7 7 2 6
12–1
12–2
13
Light Pen Parameters
Enable Light Pen Mode – Select this option if
³ 4 1 5 5 2 4 the scanner will be used in place of a light pen.
It provides light pen emulation of each bar code
scanned.
* Bars High
³ 1 1 6 9 1 7
Spaces High
³ 1 1 6 9 0 7
13–1
Set Narrow Element Width
10x Narrow Element Border – Allows the
³ 1 1 6 9 1 2 transmission of Light Pen/Wand emulation using
a 10x border.
13–2
14
IBM® 46xx Configuration
IBM Port
Enable RS485 Communication – For RS485
³ 4 1 5 5 0 4 communications. Not all scanners support this
interface. The correct interface board is required.
IBM Reserved #2
³ 3 1 7 2 1 0
IBM Reserved #3
³ 3 1 7 2 2 0
IBM Reserved #5
³ 3 1 7 2 4 0
14–1
14–2
15
USB
Enable USB Interface♦
³ 4 1 5 5 1 1 4
15–1
Enable Uni-Directional USB Serial Emulation
³ 3 1 6 4 7 0 Mode –Supported in Honeywell MS9500,
MS5100 and IS4125 laser-class products.
Note: This bar code enables Bi-Directional USB
Serial Emulation Mode in the Honeywell
®
Focus area-imaging products.
15–2
16
Code Bytes Usage
The scanner must be in Configuration Mode for the features requiring code
bytes for configuration. The Enter/Exit Configuration Mode bar code must be
scanned before starting the configuration cycle. User configurable prefix/suffix
characters can then be saved by scanning the 3 digit decimal equivalent of the
ASCII character into the appropriate character location with the code byte bar
codes.
Code Byte 1
³ 1
Code Byte 2
³ 2
Code Byte 3
³ 3
Code Byte 4
³ 4
Code Byte 5
³ 5
Code Byte 6
³ 6
Code Byte 7
³ 7
16–1
Code Byte 8
³ 8
Code Byte 9
³ 9
Reserved Codes
~ Enable Reserved Code – Contact Honeywell for
³ 9 9 9 9 8 8 information about this feature.
16–2
ASCII Reference Table
Decimal Value/ Control
HEX Value Character
Code Byte Value Keyboard Eqv
00 000 NUL @
01 001 SOH A
02 002 STX B
03 003 ETX C
04 004 EOT D
05 005 ENQ E
06 006 ACK F
07 007 BEL G
08 008 BS H
09 009 HT I
0A 010 LF J
0B 011 VT K
0C 012 FF L
0D 013 CR M
0E 014 SO N
0F 015 SI 0
10 016 DLE P
11 017 DC1 Q
12 018 DC2 R
13 019 DC3 S
14 020 DC4 T
15 021 NAK U
16 022 SYN V
17 023 ETB W
18 024 CAN X
19 025 EM Y
1A 026 SUB Z
1B 027 ESC [
1C 028 FS \
16–3
Decimal Value/ Control
HEX Value Character
Code Byte Value Keyboard Eqv
1D 029 GS ^
1E 030 RS _
1F 031 US space,blank
20 032 SP
21 033 !
22 034 “
23 035 #
24 036 $
25 037 %
26 038 &
27 039 ‘ apostrophe
28 040 (
29 041 )
2A 042 *
2B 043 +
2C 044 , comma
2D 045 - minus
2E 046 . period
2F 047 /
30 048 0 number zero
31 049 1 number one
32 050 2
33 051 3
34 052 4
35 053 5
36 054 6
37 055 7
38 056 8
39 057 9
3A 058 :
3B 059 ;
16–4
Decimal Value/ Control Keyboard
HEX Value Character
Code Byte Value Eqv
3C 060 < less than
3D 061 =
3E 062 > greater than
3F 063 ?
40 064 @ shift P
41 065 A
42 066 B
43 067 C
44 068 D
45 069 E
46 070 F
47 071 G
48 072 H
49 073 I letter l
4A 074 J
4B 075 K
4C 076 L
4D 077 M
4E 078 N
4F 079 O letter O
50 080 P
51 081 Q
52 082 R
53 083 S
54 084 T
55 085 U
56 086 V
57 087 W
58 088 X
59 089 Y
16–5
Decimal Value/ Control Keyboard
HEX Value Character
Code Byte Value Eqv
5A 090 Z
5B 091 [ shift K
5C 092 \ shift L
5D 093 ] shift M
5E 094 ^ à,shift N
5F 095 _ ♣, shift 0, underscore
60 096 ‘ accent grave
61 097 a
62 098 b
63 099 c
64 100 d
65 101 e
66 102 f
67 103 g
68 104 h
69 105 I
6A 106 j
6B 107 k
6C 108 l
6D 109 m
6E 110 n
6F 111 o
70 112 p
71 113 q
72 114 r
73 115 s
74 116 t
75 117 u
76 118 v
77 119 w
78 120 x
16–6
Decimal Value/ Control
HEX Value Character
Code Byte Value Keyboard Eqv
79 121 y
7A 122 z
7B 123 {
7C 124 | vertical slash
7D 125 } alt mode
7E 126 ~ (alt mode)
7F 127 DEL delete, rubout
16–7
At Scan PS2 Scan Prefix/Suffix Value
Key 3151
Code Code Hex = Decimal
F8 0AH 42H 3FH 97H = 151
F9 01H 43H 47H 98H = 152
F10 09H 44H 4FH 99H = 153
F11 78H 57H 56H 9AH = 154
F12 07H 58H 5EH 9BH = 155
Numeric + 79H 4EH 00H 9CH = 156
Numeric - 7BH 4AH 7CH 9DH = 157
Numeric * 7CH 37H 00H 9EH = 158
Caps Lock 58H 3AH 14H 9FH = 159
Num Lock 77H 45H 00H A0H = 160
Left alt 11H 38H 00H A1H = 161
Left Ctrl 14H 1DH 11H A2H = 162
Left Shift 12H 2AH 12H A3H = 163
Right Shift 59H 36H 59H A4H = 164
Print Screen Multiple 00H 00H A5H = 165
Tab ODH OFH 0DH A6H = 166
Shift Tab 8DH 8FH 65H A7H = 167
Enter 5AH 1CH 5AH A8H = 168
ESC 76H 01H 08H A9H = 169
Left ALT Make 11H 36H 00H AAH = 170
Left ALT Break 11H B6H 00H ABH = 171
Left CTRL Make 14H 1DH 00H ACH = 172
Left CTRL Break 14H 9DH 00H ADH = 173
*Left ALT + 1 character 11H 36H 00H AEH = 174
*Left Crtl + 1 character 14H 1DH 00H AFH = 175
*Send 58H C0H = 192
Clear 6FH C1H = 193
Jump 76H C2H = 194
Send Line 7EH C3H = 195
Erase EOF 6DH C4H = 196
Send - Make Only 58H C5H = 197
* Example:
1st Configurable Prefix = 174
2nd Configurable Prefix = 065
Scanner will transmit <left ALT Make> “A” <Left ALT Break>
16–8
17
MS9520 Voyager® and
MS9540 VoyagerCG® Series
Activation Range
Use these bar codes to select infrared (IR) sensor activation range for sensing
when objects are placed in the scan field.
* Long Range In Stand
³ 1 1 8 7 0 5
CodeGate Status
Use the following bar codes to control button functions.
Note: The following functions are not supported by all versions of the MS5145.
CodeGate Active in Stand
³ 1 1 8 7 0 7
17–1
* CodeGate Active Out of Stand
³ 1 1 8 7 1 3
Laser/Scan Modes
* Normal Scan – The laser turns on after the IR
³ 4 1 8 3 0 4 senses a bar code. The laser remains on for
approximately 3 to 10 seconds.
17–2
Same Symbol Time Outs
If using an MS5145 Eclipse, the MS9524 or MS9544 VoyagerPDF, go to
page 7–3.
No Same Symbol Time Out
³ 8 1 8 9 0 0
17–3
MS9520-00 and MS9540-00 Laser Emulation Mode
The MS9520-00 and MS9540-00 leave the factory with Laser Emulation
interface enabled.
If you recall defaults while re-configuring your scanner, scan the following bar
code to re-enable the Laser Emulation interface. The scanner you are using
must be labeled as an MS9520-00 or MS9540-00 to support this feature.
³ 9 9 9 9 7 9
If host controlled laser emulation is required scan the following bar code after
scanning the Enable HH Laser Emulation bar code.
³ 1 1 7 0 1 0
17–4
18
MS9524 and MS9544
VoyagerPDF® Series
* Enable PDF
³ 1 0 0 0 1 0
Disable PDF
³ 1 0 0 0 0 0
18–1
Disable GS1 DataBar 2D Linkage
³ 1 1 5 0 1 7
18–2
19
®
MS9535 VoyagerBT
®
The MS9535 can act as a client to other devices equipped with Bluetooth
wireless technology. If the device’s address is a 12-digit hex value that does
NOT start with a FNC3 (e.g., 000CA700118) the user must first scan the Get
BT Address bar code (below), and then scan the device’s address bar code.
Get BT Address
³ 0 0 0 C A 7 F F F F F F
Scan the Provide BT Service bar code (below) to place the MS9535 into
service mode. In this mode, other Bluetooth wireless technology enabled
devices can initiate a connection to the scanner.
Provide BT Service
³ 0 0 0 C A 7 0 0 0 0 0 0
19–1
Sleep in 2 Minutes – The scanner will go into
³ 8 1 9 5 1 2 0 sleep mode after the laser has been off for
2 minutes.
Sleep in 5 Minutes – The scanner will go into
³ 8 1 9 5 3 0 0 sleep mode after the laser has been off for
5 minutes.
Sleep in 10 Minutes – The scanner will go into
³ 8 1 9 5 6 0 0 sleep mode after the laser has been off for
10 minutes.
* Enable Scanning in Cradle
³ 1 2 3 9 0 7
* Disable BT Test
³ 1 2 3 7 0 6
19–2
20
MS9535-5M VoyagerBT
Enable Inventory Mode – Bar code data that is
³ 1 2 3 9 1 0
scanned is stored in the scanner’s expanded
memory base. The data will be transmitted when
the scanner is placed back into its BT cradle.
Note: A special beep will sound when a bar code
is scanned but not stored due to a full a
memory base. The scanner must be placed
in the BT cradle to empty the memory.
* No Transmit/Entry Counter
³ 1 2 3 9 0 4
20–1
Clear Inventory Records – Will clear all stored
³ 9 9 8 0 4 9 bar code data in memory.
* Maintain Records
³ 1 2 5 6 0 2
20–2
Inventory Quantity Bar Codes**
The following inventory quantity bar codes will enable the user to enter a
quantity from 1 to 9999 for the last item (bar code) scanned. The item’s bar
code data will be retransmitted as many times as the quantity indicates.
Example:
1. Scan the item’s bar code (ie. ABCD)
2. Scan the Quantity 1 bar code
3. Scan the Quantity 0 bar code
4. The ABCD bar code will be transmitted 10 times
Quantity 0
³ Q 0
Quantity 1
³ Q 1
Quantity 2
³ Q 2
Quantity 3
³ Q 3
Quantity 4
³ Q 4
Quantity 5
³ Q 5
Quantity 6
³ Q 6
Quantity 7
³ Q 7
Quantity 8
³ Q 8
Quantity 9
³ Q 9
** Transmit Quantity Field must be enabled (on page 20–2) for this feature.
20–3
20–4
21
IS4125 and IS4225 Scan Engines
Disable Old Serial Program
³ 1 2 0 3 1 5
Recall Defaults
³ 9 9 9 9 9 8
21–1
21–2
22
IS4823 and IS4825 Scan Engines
Operating Modes
Activation Modes
* Activate Scanning with the External Trigger –
³ 4 1 8 3 0 4 An external I/O pin is used to enable the scanning
cycle. A High-to-Low transition on the I/O signal is
used to activate scanning. The signal must be
deactivated (HIGH) and re-activated for
subsequent scanning cycles. The scanning cycle
is terminated based on the default period of time
(2 seconds), a variable period of time, when the
I/O signal is deactivated (Low-to-High), or when a
bar code is scanned and transmitted.
22–1
Activation Mode Features
~ Variable Laser-On Time Out – Scan this bar
³ 9 1 9 6 0 0 code with a code byte sequence (on page 16–1)
that represents the desired time out increment.
The configurable time increment (1-second
increments) selected is the scanning laser-on
time.
22–2
Detect and Notify Mode (Monitor the External
³ 1 2 0 3 1 3 Trigger) – The external I/O pin used in the default
activation mode is monitored during the inactive
laser cycles. An <SI> is transmitted when the I/O
is active and an <SO> when it is inactive. Once
the scanning activation cycle is started, the
external I/O monitoring status is maintained until
the scanning cycle is terminated regardless of the
actual I/O level.
Continuous Blinky Mode
Continuous Blinky Mode – The scanner will
³ 4 1 8 3 3 4 continuously blink on and off, turning the scanning
cycle on and off for all normal scanner operations.
If a bar code is scanned and transmitted, the same
symbol timeout is maintained throughout the cycle
preventing additional scans of the same bar code
when the scanner is in default mode.
Sleep Mode
~ Sleep Mode – A power saving mode that can
³ 9 1 9 5 0 0 be configured to occur in 1-second increments.
Use this code with a code byte sequence
(on page 16–1) that represents the desired
increment.
22–3
22–4
23
Miscellaneous Features
Custom Defaults
Honeywell manufactures several scanners for OEM applications. These
scanners may use a different set of defaults than Honeywell factory defaults.
Scanning the bar code will reset the default table to Honeywell defaults.
Recall Defaults
³ 9 9 9 9 9 8
23–1
Serial Program Mode
For Serial Program Mode, all commands must be framed by an STX (02 Hex)
and ETX (03 Hex).
To recall defaults:
1. Transmit <STX>999999<ETX> through the Serial Port. This will put the
scanner in serial program mode. Scanning will be suspended and the
scanner will respond with an ACK (06 Hex).
3. Transmit <STX>999999<ETX> through the Serial Port. This will cause the
scanner to exit program mode and save the new settings. The scanner will
beep 3 times and send an ACK (06 Hex).
If at anytime, the scanner cannot recognize a command, it will respond with a
NAK (15 Hex).
23–2
24
Customer Support
Technical Assistance
If you need assistance installing or troubleshooting your device, please call
your distributor or the nearest technical support office:
North America/Canada
Telephone: (800) 782-4263
E-mail: [email protected]
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
E-mail: [email protected]
Brazil
Telephone: +55 (11) 5185-8222
Fax: +55 (11) 5185-8225
E-mail: [email protected]
Mexico
Telephone: 01-800-HONEYWELL (01-800-466-3993)
E-mail: [email protected]
Europe, Middle East, and Africa
Telephone: +31 (0) 40 7999 393
Fax: +31 (0) 40 2425 672
E-mail: [email protected]
Hong Kong
Telephone: +852-29536436
Fax: +852-2511-3557
E-mail: [email protected]
Singapore
Telephone: +65-6842-7155
Fax: +65-6842-7166
E-mail: [email protected]
China
Telephone: +86 800 828 2803
Fax: +86-512-6762-2560
E-mail: [email protected]
Japan
Telephone: +81-3-3839-8511
Fax: +81-3-3839-8519
E-mail: [email protected]
24–1
Product Service and Repair
Honeywell International Inc. provides service for all its products through
service centers throughout the world. To obtain warranty or non-warranty
service, contact the appropriate location below to obtain a Return Material
Authorization number (RMA #) before returning the product.
North America
Telephone: (800) 782-4263
E-mail: [email protected]
Latin America
Telephone: (803) 835-8000
Telephone: (800) 782-4263
Fax: (239) 263-9689
E-mail: [email protected]
Brazil
Telephone: +55 (11) 5185-8222
Fax: +55 (11) 5185-8225
E-mail: [email protected]
Mexico
Telephone: 01-800-HONEYWELL (01-800-466-3993)
Fax: +52 (55) 5531-3672
E-mail: [email protected]
Europe, Middle East, and Africa
Telephone: +31 (0) 40 2901 633
Fax: +31 (0) 40 2901 631
E-mail: [email protected]
Hong Kong
Telephone: +852-29536436
Fax: +852-2511-3557
E-mail: [email protected]
Singapore
Telephone: +65-6842-7155
Fax: +65-6842-7166
E-mail: [email protected]
China
Telephone: +86 800 828 2803
Fax: +86-512-6762-2560
E-mail: [email protected]
Japan
Telephone: +81-3-3839-8511
Fax: +81-3-3839-8519
E-mail: [email protected]
24–2
Online Product Service and Repair Assistance
You can also access product service and repair assistance online at
www.honeywellaidc.com
24–3
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywellaidc.com
00-02544 Rev K
2/11