QUESTION 1

Refer to the exhibit. Which two commands were used to create port channel 10? (Choose two.)

A. int range g0/0-1

channel-group 10 mode active
B. int range g0/0-1
channel-group 10 mode desirable
C. int range g0/0-1
channel-group 10 mode passive
D. int range g0/0-1
channel-group 10 mode auto
E. int range g0/0-1
channel-group 10 mode on

QUESTION 2
Refer to the exhibit. An administrator is tasked with configuring a voice VLAN. What is the expected
outcome when a Cisco phone is connected to the GigabitEthernet 3/1/4 port on a switch?

A. The phone and a workstation that is connected to the phone do not have VLAN connectivity.
B. The phone sends and receives data in VLAN 50, but a workstation connected to the phone sends and
receives data in VLAN 1.
C. The phone sends and receives data in VLAN 50, but a workstation connected to the phone has no
VLAN connected.
D. The phone and a workstation that is connected to the phone send and receive data in VLAN 50.
 QUESTION 3
Refer to the exhibit. Which action is expected from SW1 when the untagged frame is received on the
GigabitEthernet0/1 interface?

A. The frame is processed in VLAN 1

B. The frame is processed in VLAN 11
C. The frame is processed in VLAN 5
D. The frame is dropped

QUESTION 4
Refer to the exhibit. What two conclusions should be made about this configuration? (Choose two.)

A. The root port is FastEthernet 2/1

B. The designated port is FastEthernet 2/1
C. The spanning-tree mode is PVST+
D. This is a root bridge
E. The spanning-tree mode is Rapid PVST+

QUESTION 5
A network engineer must create a diagram of a multivendor network. Which command must be configured
on the Cisco devices so that the topology of the network can be mapped?

A. Device(config)#lldp run
B. Device(config)#cdp run
C. Device(config-if)#cdp enable
D. Device(config)#flow-sampler-map topology
QUESTION 6
How do AAA operations compare regarding user identification, user services, and access control?

A. Authorization provides access control, and authentication tracks user services

B. Authentication identifies users, and accounting tracks user services

C. Accounting tracks user services, and authentication provides access control

D. Authorization identifies users, and authentication provides access control

QUESTION 7
What is difference between RADIUS and TACACS+?

A. RADIUS logs all commands that are entered by the administrator, but TACACS+ logs only start, stop,
and interim commands.
B. TACACS+ separates authentication and authorization, and RADIUS merges them.
C. TACACS+ encrypts only password information, and RADIUS encrypts the entire payload.
D. RADIUS is most appropriate for dial authentication, but TACACS+ can be used for multiple types of
authentication.

QUESTION 8
What is a difference between local AP mode and FlexConnect AP mode?

A. Local AP mode creates two CAPWAP tunnels per AP to the WLC

B. Local AP mode causes the AP to behave as if it were an autonomous AP
C. FlexConnect AP mode fails to function if the AP loses connectivity with the WLC
D. FlexConnect AP mode bridges the traffic from the AP to the WLC when local switching is configured

QUESTION 9

Refer to the exhibit. What does router R1 use as its OSPF router-ID?

A. 10.10.1.10
B. 10.10.10.20
C. 172.16.15.10
D. 192.168.0.1

QUESTION 10
When OSPF learns multiple paths to a network, how does it select a route?

A. For each existing interface, it adds the metric from the source router to the destination to calculate the
route with the lowest bandwidth.
B. It counts the number of hops between the source router and the destination to determine the route with
the lowest metric.
C. It divides a reference bandwidth of 100 Mbps by the actual bandwidth of the exiting interface to calculate
the route with the lowest cost.
D. It multiplies the active K values by 256 to calculate the route with the lowest metric.
QUESTION 11
When a floating static route is configured, which action ensures that the backup route is used when the
primary route fails?

A. The administrative distance must be higher on the primary route so that the backup route becomes
secondary.
B. The default-information originate command must be configured for the route to be installed into the
routing table.
C. The floating static route must have a lower administrative distance than the primary route so it is used
as a backup.
D. The floating static route must have a higher administrative distance than the primary route so it is used
as a backup

QUESTION 12

Refer to the exhibit. The show ip ospf interface command has been executed on R1. How is OSPF
configured?

A. A point-to-point network type is configured.

B. The interface is not participating in OSPF.
C. The default Hello and Dead timers are in use.
D. There are six OSPF neighbors on this interface.

QUESTION 13
A user configured OSPF and advertised the Gigabit Ethernet interface in OSPF. By default, which type of
OSPF network does this interface belong to?

A. point-to-multipoint
B. point-to-point
C. broadcast
D. nonbroadcast
QUESTION 14
Which attribute does a router use to select the best path when two or more different routes to the same
destination exist from two different routing protocols?
A. dual algorithm
B. metric
C. administrative distance
D. hop count

QUESTION 15
Router A learns the same route from two different neighbors; one of the neighbor routers is an OSPF
neighbor, and the other is an EIGRP neighbor.

What is the administrative distance of the route that will be installed in the routing table?

A. 20
B. 90
C. 110
D. 115

QUESTION 16

Refer to the exhibit. An engineer is bringing up a new circuit to the MPLS provider on the Gi0/1 interface of
Router 1. The new circuit uses eBGP and learns the route to VLAN25 from the BGP path.

What is the expected behavior for the traffic flow for route 10.10.13.0/25?

A. Traffic to 10.10.13.0/25 is load balanced out of multiple interfaces.

B. Traffic to 10.10.13.0/25 is asymmetrical.
C. Route 10.10.13.0/25 is updated in the routing table as being learned from interface Gi0/1.
D. Route 10.10.13.0/25 learned via the Gi0/0 interface remains in the routing table.
 QUESTION 17
Which two actions influence the EIGRP route selection process? (Choose two.)

A. The advertised distance is calculated by a downstream neighbor to inform the local router of the
bandwidth on the link.
B. The router calculates the feasible distance of all paths to the destination route.
C. The router must use the advertised distance as the metric for any given route.
D. The router calculates the best backup path to the destination route and assigns it as the feasible
successor.
E. The router calculates the reported distance by multiplying the delay on the exiting interface by 256.

QUESTION 18

Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to
10.10.13.128/25 at Site A?

A. It sends packets out of interface Fa0/1 only.

B. It sends packets out of interface Fa0/2 only.
C. It load-balances traffic out of Fa0/1 and Fa0/2.
D. It cannot send packets to 10.10.13.128/25.

QUESTION 19
Which two outcomes are predictable behaviors for HSRP? (Choose two.)
A. The two routers negotiate one router as the active router and the other as the standby router.
B. The two routers share the same interface IP address, and default gateway traffic is load-balanced
between them.
C. The two routers synchronize configurations to provide consistent packet forwarding.
D. Each router has a different IP address, both routers act as the default gateway on the LAN, and traffic is
load-balanced between them.
E. The two routers share a virtual IP address that is used as the default gateway for devices on the LAN.
 QUESTION 20

Refer to the exhibit. An engineer is configuring the New York router to reach the Lo1 interface of the Atlanta
router using interface Se0/0/0 as the primary path. Which two commands must be configured on the New
York router so that it can reach the Lo1 interface of the Atlanta router via Washington when the link
between New York and Atlanta goes down? (Choose two.)

A. Ipv6 route 2000::1/128 2012::1

B. Ipv6 route 2000::1/128 2012::1 5
C. Ipv6 route 2000::1/128 2012::2
D. Ipv6 route 2000::1/128 2023::2 5
E. Ipv6 route 2000::1/128 2023::3 5

QUESTION 21
How does HSRP provide first hop redundancy?

A. It load-balances Layer 2 traffic along the path by flooding traffic out all interfaces configured with the
same VLAN.
B. It uses a shared virtual MAC and a virtual IP address to a group of routers that serve as the default
gateway for hosts on a LAN.
C. It forwards multiple packets to the same destination over different routed links in the data path.
D. It load-balances traffic by assigning the same metric value to more than one route to the same
destination in the IP routing table.

QUESTION 22
R1 has learned route 192.168.12.0/24 via IS-IS, OSPF, RIP, and Internal EIGRP. Under normal operating
conditions, which routing protocol is installed in the routing table?

A. IS-IS
B. Internal EIGRP
C. RIP
D. OSPF
QUESTION 23
DRAG DROP

A network engineer is configuring an OSPFv2 neighbor adjacency. Drag and drop the parameters from the
left onto their required categories on the right. Not all parameters are used.

Select and Place:

QUESTION 24

Refer to the exhibit. The default-information originate command is configured under the R1 OSPF
configuration. After testing, workstations on VLAN 20 at Site B cannot reach a DNS server on the Internet.

Which action corrects the configuration issue?

A. Add the default-information originate command on R2.

B. Add the always keyword to the default-information originate command on R1.
C. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.18 command on R1.
D. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.2 command on R2.
 QUESTION 25

Refer to the exhibit. With which metric was the route to host 172.16.0.202 learned?

A. 0
B. 110
C. 38443
D. 3184439

QUESTION 26
A user configured OSPF in a single area between two routers. A serial interface connecting R1 and R2 is
running encapsulation PPP. By default, which OSPF network type is seen on this interface when the user
types show ip ospf interface on R1 or R2?

A. nonbroadcast
B. point-to-point
C. point-to-multipoint
D. broadcast

QUESTION 27
Which MAC address is recognized as a VRRP virtual address?

A. 0000.5E00.010a
B. 0005.3709.8968
C. 0000.0C07.AC99
D. 0007.C070.AB01

QUESTION 28
A router running EIGRP has learned the same route from two different paths. Which parameter does the
router use to select the best path?

A. as-path
B. administrative distance
C. metric
D. cost
QUESTION 29

Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and
Washington sites.

Which two tasks must be performed so that the Se0/0/0 interfaces on the Atlanta and Washington routers
can reach one another? (Choose two.)

A. Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router.
B. Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.
C. Configure the ipv6 route 2012::/126 2023::1 command on the Washington router.
D. Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.
E. Configure the ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.

QUESTION 30
An engineer configured an OSPF neighbor as a designated router. Which state verifies the designated
router is in the proper mode?

A. Init
B. 2-way
C. Exchange
D. Full

QUESTION 31

Refer to the exhibit. Which route does R1 select for traffic that is destined to 192.168.16.2?
A. 192.168.16.0/21
B. 192.168.16.0/24
C. 192.168.26.0/26
D. 192.168.16.0/27