7708SFP, 7708SFP-2, 7708SFP-2-DIN, 7708SFP-4-DIN-A

Single, Dual, and Quad Fiber Optic SFP Card Module

The Evertz 7708SFP series is a card-based equivalent to the 3405FR series 3405 series SFP’s are able to handle ASI, SDI, HD-SDI and 3G digital video
fiber optic SFP frames. The 7708SFP series can accommodate any 3405 series signals, as well as other signal rates up to 3 Gig on non-reclocked versions
SFP, allowing the SFP cages to be populated as needed with optical transmit, (e.g. MADI). The SFP modules are hot-swappable on the rear panel, allowing
receive, regenerator, changeover or electrical distribution amplifier SFP’s. for quick servicing or easy reconfiguration or expansion at any time. 16 CWDM
Any combination of 3405SFP types may be used on the same card, making wavelengths are also available, which when combined with Evertz CWDM
countless versatile combinations possible. Cards are available to hold one, products allow up to 16 signals to be multiplexed on to a single fiber, greatly
two or four SFP’s making them not only flexible, but also a very high-density conserving fiber usage.
and cost-effective solution for constructing modern fiber optic infrastructures.
Benefits of fiber optics for video transport include longer attainable distances, The 7708SFP modules support full remote monitoring and control over SNMP/
smaller/lighter cabling, reduced cable tray loads and electrical isolation. The VistaLINK® when used in conjunction with an Evertz frame with frame controller
7708SFP series provides a low-overhead means for simple electrical/optical module. Numerous parameters such as optical power and electrical signal
conversion for interfacility transport, as well as overcoming the limitations presence and rate can be accessed remotely to monitor system integrity.
imposed by coaxial cable in intra-facility applications.

Features & Benefits

• Models available to hold one, two or four SFP’s to suit different capacity • SFP modules are hot-swappable from the rear plate
requirements • 7708SFP card modules are hot swappable through the front of the frame
• Models available with BNC or DIN 1.0/2.3 connectors to suit different density • Comprehensive signal and card status monitoring via four digit card edge
or connector preferences display or remotely through SNMP and VistaLINK® when used in conjunction
• Any combination of 3405SFP types may be installed in a single card, including with an Evertz frame controller module
optical transmit, receive, regenerator and electrical distribution amplifiers

1A 7708SFP-2
ASI/SDI/ 7708SFP
7708SFP-2
1B Optical -DIN
7708SFP-4-DIN-A

HD-SDI/3G Evertz 3405 Series SFP 1A

1C Input/Output
Input/Output

1B
1A 1B
1D

B
1D

SFP1
1B

SFP1
Optical ports can be inputs or 1C 1D

1B
Number of SFP’s that can be installed
outputs depending on the model

A
depends on model:

B
Electrical ports can be inputs or outputs

SFP1
7708SFP: 1 SFP of 3405SFP installed.
depending on the model of 3405SFP 2A 2B
7708SFP-2, 7708SFP-2-DIN: 2 SFP’s Ports are electrical DIN 1.0/2.3 1C

B
installed.

A
instead of optical if 3405DA5 is

SFP2
7708SFP-4-DIN-A: 4 SFP’s

1D
2C 2D
used.

1C
B

A
SFP1
nA
ASI/SDI/ 1D
3A 3B

1A
HD-SDI/3G
nB Optical

B
A
Evertz 3405 Series SFP

SFP2

SFP3
Input/Output
nC Input/Output 3C 3D

2B

A
A
nD 2A

2D
4A 4B

B
1C

SFP4
B
4C 4D

SFP2
2B

A
A
TM
VistaLINK

1A
Dot Matrix Display

2C
Interface 2C
Monitoring &
Control

2A
Toggle Switch/
pushbutton
LED Indicators
2D

SFP Options
The 7708SFP series is compatible with any 3405 series optical or coaxial SFP. and for coaxial SFP options please see the "3405 Coaxial SFP Series" data
The Complete Solution Provider

For optical SFP options, please see the "3405 Optical SFP Series" data sheet, sheet.

Specifications
System: Electrical Outputs: Physical (number of slots):
Density: Connector: 7708SFP: 1
7708SFP: 1 SFP module 7708SFP: BNC per IEC 61169-8 Annex A 7708SFP-2: 2
7708SFP-2: Up to 2 SFP modules 7708SFP-2: BNC per IEC 61169-8 Annex A 7708SFP-2-DIN: 1
7708SFP-2-DIN: Up to 2 SFP modules 7708SFP-2-DIN: DIN 1.0/2.3 7708SFP-4-DIN-A: 2
7708SFP-4-DIN-A: Up to 4 SFP modules 7708SFP-4-DIN-A: DIN 1.0/2.3
Impedance: 75Ω Impedance: 75Ω (nominal) Electrical:
Return Loss: >15dB to 1.5GHz Voltage: +12V DC
Electrical Inputs: >10dB to 3GHz Power: 11W
Connector:
7708SFP: BNC per IEC 61169-8 Annex A Compliance:
7708SFP-2: BNC per IEC 61169-8 Annex A EMI/RFI: Complies with FCC part 15, Class A
7708SFP-2-DIN: DIN 1.0/2.3 Complies with EU EMC Directives
7708SFP-4-DIN-A: DIN 1.0/2.3
Equalization: Automatic to 80m @ 3 Gb/s 100m@
Return Loss: > 15dB up to 1.5GHz
> 10dB up to 3GHz

Ordering Information
7708SFP Single Fiber Optic SFP card module with BNC I/O Enclosures
7708SFP-2 Dual Fiber Optic SFP card module with BNC I/O 350FR 3RU Portable Multiframe which holds up to 7 single slot modules
7708SFP-2-DIN Dual Fiber Optic SFP card module with DIN 1.0/2.3 I/O 7700FR-C 3RU Multiframe which holds up to 15 single slot modules
7708SFP-4-DIN-A Quad Fiber Optic SFP card module with DIN 1.0/2.3 I/O 7800FR 3RU Multiframe which holds up to 15 single slot modules

Ordering Options Rear Plate must be specified at time of order

(Eg: Model +3RU)

Evertz SFP modules

The 7708SFP series is compatible with any 3405 series optical or coaxial SFP. For optical
SFP options, please see the "3405 Optical SFP Series" data sheet, and for coaxial SFP
options please see the "3405 Coaxial SFP Series" data sheet.

Rev. 15-2