0% found this document useful (0 votes)
13 views2 pages

Assignment MT (OBE) - 1

Uploaded by

xdbenerobe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
13 views2 pages

Assignment MT (OBE) - 1

Uploaded by

xdbenerobe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Sl.

No #

American International University- Bangladesh (AIUB)


Faculty of Engineering

Course Name: Electronic Devices Course Code: EEE 2103


Semester: Summer 2022-23 Term: Mid
July 06, 2023
Total Marks: 20 Submission Date:
(11 to 1 PM)
Faculty Name: Ms. Sadia Yasmin Assignment: OBE
Course Outcome Mapping with Questions
Obtained
Item COs POIs K P A Marks
Marks
Q1 CO1 P.b.1.C4 K1 - - 20

Student Information:

Student Name: Student ID:

Section: Department:

Marking Rubrics (to be filled by Faculty):


Needs No
Excellent Proficient Good Acceptable Improvement Unacceptable Secured
Problems Response
[14] [13-11] [12-9] [8-7] [6-3] [2-1] Marks
[0]
Detailed unique Response
response Response with shows Partial problem is
explaining the no apparent understanding solved; response
systematic errors and the of the problem, indicates part of Unable to
answer is the problem was Partial problem
diode theories but the solved with minor clarify the
correct, but not understood No Response
properly and systematic error that needs to understanding
Q1 answer is systematic diode theories clearly and partial of the problem
(i) diode theories application of be fixed.
correct with all applications/ex and systematic
works clearly. explanation is planations may systematic diode diode theories.
shown. not adequate. not be correct. theories.
Needs
Excellent Proficient Good Acceptable Unacceptable No Response Secured
Improvement
Problems [6] [5] [4] [3] [1] Marks
[2] [0]
Detailed unique
Response with Unable to
response
no apparent Partial problem clarify the
explaining the Response shows Partial problem is
errors and the solved with understanding
concept understanding solved; response
answer is no/vague of the problem
properly and of the problem, indicates part of No Response
correct, but conclusion and method of
Q1 answer is but the final the problem was
explanation is regarding the problem
(ii) correct with all answer may not not understood
not optimum choice of solving was not
works clearly be correct clearly.
adequate/unique. component correct.
shown.

Comments Total marks (20)

Instructions:
1. Separate cover page is provided for this assignment. Different cover page or without cover page, assignment
submission will not be acceptable.
2. No late submission is allowed.
3. Fill up the table and then start writing your answer.
4. Note: Copied/identical submissions will be graded as 0 for all parties concerned.
Instructions Related to Use Variables:
Note that this problem uses the variables a, b, c, d, and e, which are the digits of middle of your student ID (22-abcde-1).
If any of the value is zero, assume it ‘5’.
a b c d e
Zero level detector:
In any of your projects in Fig-1, you are required to detect zero level using an AND gate. Your task is to create a
square wave pulse using diode. Diode will only be used to construct AND gate, and AC source is only available.
Now, you need to observe the AND operations and your available AC supply is given, (ab+220) V (rms) at 50
Hz. You are asked to design a dc source of having the output, Vo of [(c+d+e) mV x 10]. This Vo could be
considered as the supply/Reference for the AND operations (Diode Logic only).
Now, for 2 input AND operation, Input-1 pulse will be generated from another AC power supply with 35sinωt
and input-2 will be kept grounded. Output can be observed through the ‘Red’ LED with an angular frequency, ω
= ((b+c+d)*(a+e)) radians to understand the AND gate operations.
Design parameters constraints: Consider the peak voltage of the AC supply is smaller than the PIV of the diodes.
All the diodes are considered Si (~0.7V) and Zener diode, Capacitor, Resistors, LED, etc. will be considered to
meet your assignment outcome to meet the objectives.

Zener diode,

Figure 1: Block diagram for the signal rectification and AND gate operation

Based on this criterion, prepare the following:

1. Sketch all the step-by-step procedure and construct the connection in a single circuit and analyze each
part of the circuits. [Marks: 14]

2. Show the calculation so that ‘Red’ LED will indicate the output pulse as per the AND operation.
[Marks: 06]

You might also like