Scribd
Upload
9 views

Assignment ED - Final Term Spring 2022 - 23

The document provides information about an electronics course assignment, including course details, student information, assignment questions, and submission instructions. The assignment contains 4 questions regarding circuit analysis, requiring students to analyze input and output impedance and voltage gain, and draw equivalent circuit models. Special submission instructions are also provided.

Uploaded by

xdbenerobe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

Assignment ED - Final Term Spring 2022 - 23

The document provides information about an electronics course assignment, including course details, student information, assignment questions, and submission instructions. The assignment contains 4 questions regarding circuit analysis, requiring students to analyze input and output impedance and voltage gain, and draw equivalent circuit models. Special submission instructions are also provided.

Uploaded by

xdbenerobe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

American International University- Bangladesh (AIUB)

Faculty of Engineering

Course Name: Electronic Devices Course Code: EEE 2103


Semester: Spring 2022-23 Term: Final
Total Marks: 20 Submission Date: 30-11-2022
Faculty Name: Dr. Md. Rifat Hazari

Course Outcome Mapping with Questions


Obtained
Item COs POIs K P A Marks
Marks
Q1 CO3 P.b.2.C4 K2 5
Q2 CO3 P.b.2.C4 K2 5
Q3 CO3 P.b.2.C4 K2 5
Q4 CO3 P.b.2.C4 K2 5
Total: 20

Student Information:
Student Name: Student ID:

Section: Department:

Marking Rubrics (to be filled by Faculty):


Excellent Proficient Good Acceptable Unacceptable No Response
[5] [4] [3] [2] [1] [0]
Detailed unique
No
response Response with no Partial problem is Unable to clarify
Response shows Response/(Copie Secured
Problem # explaining the apparent errors solved; response the understanding
understanding of d/identical Marks
concept properly and the answer is indicates part of of the problem and
the problem, but submissions will
and answer is correct, but the problem was method of the
the final answer be graded as 0
correct with all explanation is not not understood problem solving
may not be correct for all parties
works clearly adequate/unique. clearly. was not correct
concerned)
shown.
1

Comments Total marks (20)


Instructions:
1. If your question says ID+10 then use last two digits of your ID before the hyphen
and then add 10. For example, If ID: 18-78253-2, then use 53 and add 10. In this
case, ID+10= 53+10 = 63. Similar for ID+30, ID+40, respectively.
2. Answer of all the answer is compulsory.
3. Copied/identical submissions will be graded as 0.
4. Special Instructions are provided in the 3rd page of this assignment questions.

1. For the given circuit of Fig. 1, analyze the following: Zi, Zo, Av with ro = ID+10 kΩ, and ID+40 kΩ.
Draw the equivalent model to analyze the parameters.
2. For the given circuit of Fig. 2, analyze the following: Zi, Zo, Av for ID+30 kΩ with and without considering
capacitor across the emitter resistance. Draw the equivalent models for both conditions to analyze the
parameters.

Figure for Question 1 Figure for Question 2

3. For the given circuit of Fig. 3, analyze the following: Zi, Zo, Av. with and without considering the 10 µF
capacitor. Draw the equivalent models to analyze the parameters for both conditions.

4. For the given circuit of Fig. 4, analyze the following: Zi, Zo, Av with ro = 80 kΩ. Draw the equivalent
model to analyze the parameters.

Figure for Question 3 Figure for Question 4

Page 2 of 3
Special Instructions of Assignment
1. After finishing your assignment, please scan it using suitable apps using your mobile phone and make it
pdf file. The 1st page will be cover page (follow step 3).
2. The assignment file name should be your ID.
3. Please use the top page of this assignment as cover page. Please fill up Name, ID, Section etc very
carefully.
Online Submission Guidelines:
1. Click on the view assignment in Microsoft teams as shown below. You will get it in our class in Microsoft
teams.

2. After that, click on the Add work. Here you can upload your assignment.
3. After upload, click on the Turn in option (laptop view) or click Hand In option (mobile view).

If you have any confusions, feel free to contact with me.

With best regards,


Dr. Rifat

Page 3 of 3

You might also like