Hardware documentation of

DS0207-02 board

(Current Sink and Source)

dSPACE GmbH
Technologiepark 25
D-33100 Paderborn
Deutschland
www.dspace.de
 dSPACE DS0207-02 (Current Sink and Source)

Table of contents
1 General Description .................................................. 3
2 Connectors................................................................ 7
3 Serial EEPROM .......................................................... 8
4 Datasheet ................................................................. 8

dSPACE GmbH
2
 dSPACE DS0207-02 (Current Sink and Source)

1 General Description
The dS0207 current sink source output module was designed for simulation of current interface
equipped sensors. The module is part of a compound of different dSPACE boards, which together
form a powerful testing tool, a dSPACE Hardware in the loop simulator (HIL). It is a 8 channel voltage
controlled current sink and source, each channel consisting of a separate sink and source.
The following functional block diagram shows one out of eight current output channels:

dSPACE Signal Customer Signal

SINK PATH

K*Uin

Module Input Module Output

(dSPACE IO) (Backplane / ECU)
Uin +15V

K*Uin
SOURCE
dSPACE Reference
PATH Customer Reference

Figure 1: functional block diagram

dSPACE GmbH
3
 dSPACE DS0207-02 (Current Sink and Source)

Please notice, that the current sink will only work with a positive voltage with respect to system GND
and the current source only with a negative voltage with respect to +15V. The module is fully pro-
tected against voltage levels from 0V up to 50V in the standard configurations.
There are six possible modes of operation, three “main” modes, available as standard configurations
and three user definable modes, derived from the main modes. These modes make changes concern-
ing the transfer characteristic of the DS0207 possible and require additional resistors:

Mode Uin K K*Uin Remark

V mA/V mA
Analog 0 2.5 0 standard configuration, no resistor changes necessary,
.. .. suitable for dSPACE standard IO analog output channels
10 25
Analog 0 user 0 user definable configuration, resistor changes necessary,
Modified .. defined .. suitable for dSPACE standard IO analog output channels
10 user
defined
Digital <1.56 14V/Uin 14 standard configuration, no resistor changes necessary,
>2.34 0V/Uin 0 suitable for dSPACE standard IO digital / pwm output
channels, notice that output to input chartacteristic is
LOGIC NOT!
Digital <1.56 user hi- user definable configuration, resistor changes necessary,
Modified defined current suitable for dSPACE standard IO digital / pwm output
>2.34 channels, notice that output to input chartacteristic is
0V/Uin 0 LOGIC NOT!
Digital Off- <1.56 14V/Uin 14 standard configuration, no resistor changes necessary,
set suitable for dSPACE standard IO digital / pwm output
>2.34 7V/Uin 7 channels, notice that output to input chartacteristic is
LOGIC NOT!
Digital Off- <1.56 user hi- user definable configuration, resistor changes necessary,
set Modi- defined current suitable for dSPACE standard IO digital / pwm output
fied >2.34 channels, notice that output to input chartacteristic is
user low- LOGIC NOT!
defined current

Table 1: mode selection

dSPACE GmbH
4
 dSPACE DS0207-02 (Current Sink and Source)

The following drawings show the DS0207-02 configuration elements on the component side with the
six different configurations. The resistor values for the “modified” operating modes can be calculated
using the EXCEL sheet:
0207_02_cfg.xls

R1 CH... R1 CH...
MOD MOD
A D A D A D A D
R2 R2

D O D O
R3 R3

Configuration Analog 0..10V -> 0..25mA Configuration Analog Modified 0..10V -> 0..xxmA

R1 CH... R1 CH...
MOD MOD
A D A D A D A D
R2 R2

D O D O
R3 R3

Configuration Digital Modified <1.56V -> xxmA

Configuration Digital <1.56V -> 14mA >2,34V ->0mA
>2,34V ->0mA

R1 CH... R1 CH...
MOD MOD
A D A D A D A D
R2 R2

D O D O
R3 R3

Configuration Digital Offset <1.56V -> 14mA Configuration Digital Offset Modified <1.56V -> yymA
>2,34V -> 7mA >2,34V -> xxmA

: Solder Pads

: Resistor Pads

Figure 2: mode configuration

dSPACE GmbH
5
 dSPACE DS0207-02 (Current Sink and Source)

The next figure shows the component side of the dS0207-02:

P2

2
P1

Figure 3: component side

dSPACE GmbH
6
 dSPACE DS0207-02 (Current Sink and Source)

2 Connectors
Connector P1 carries the signals of the connected dSPACE I/O board
Connector P2 carries the conditioned signals wired to the customers hardware

P1 Pin Signal________________________________________
1 Uin Channel 0 (from dSPACE standard board, signal pin)
2 GND (from dSPACE standard board, reference pin)
3 Uin Channel 1 (from dSPACE standard board, signal pin)
4 GND (from dSPACE standard board, reference pin)
5 Uin Channel 2 (from dSPACE standard board, signal pin)
6 GND (from dSPACE standard board, reference pin)
7 Uin Channel 3 (from dSPACE standard board, signal pin)
8 GND (from dSPACE standard board, reference pin)
9 Uin Channel 4 (from dSPACE standard board, signal pin)
10 GND (from dSPACE standard board, reference pin)
11 Uin Channel 5 (from dSPACE standard board, signal pin)
12 GND (from dSPACE standard board, reference pin)
13 Uin Channel 6 (from dSPACE standard board, signal pin)
14 GND (from dSPACE standard board, reference pin)
15 Uin Channel 7 (from dSPACE standard board, signal pin)
16 GND (from dSPACE standard board, reference pin)
17 +15V supply voltage from sideplane
18 -15V supply voltage from sideplane
19 +5V supply voltage from sideplane (VCC)
20 Ground (GND)
21 Wired to ADDR0 of serial EEPROM
22 Wired to ADDR1 of serial EEPROM
23 Wired to ADDR2 of serial EEPROM
24 Unused

P2 Pin Signal_______________________________________
1 Unused
2 Unused
3 Wired to clock-pin of serial EEPROM
4 Wired to data-pin of serial EEPROM
5 Ground (GND)
6 +5V supply voltage from sideplane (VCC)
7 -15V supply voltage from sideplane
8 +15V supply voltage from sideplane
9 Isource Channel 0 (to ECU / backplane, reference pin)
10 Isink Channel 0 (to ECU / backplane, signal pin)
11 Isource Channel 1 (to ECU / backplane, reference pin)
12 Isink Channel 1 (to ECU / backplane, signal pin)
13 Isource Channel 2 (to ECU / backplane, reference pin)
14 Isink Channel 2 (to ECU / backplane, signal pin)
15 Isource Channel 3 (to ECU / backplane, reference pin)
16 Isink Channel 3 (to ECU / backplane, signal pin)
17 Isource Channel 4 (to ECU / backplane, reference pin)
18 Isink Channel 4 (to ECU / backplane, signal pin)
19 Isource Channel 5 (to ECU / backplane, reference pin)
20 Isink Channel 5 (to ECU / backplane, signal pin)
21 Isource Channel 6 (to ECU / backplane, reference pin)
22 Isink Channel 6 (to ECU / backplane, signal pin)
23 Isource Channel 7 (to ECU / backplane, reference pin)
24 Isink Channel 7 (to ECU / backplane, signal pin)

dSPACE GmbH
7
 dSPACE DS0207-02 (Current Sink and Source)

3 Serial EEPROM
Reserved for future applications.

4 Datasheet
All values @ 25°C.
Parameter Min Typ Max Unit Remark
I_+15V 110 +15V supply current, open load
I_-15V 20 -15V supply current, open load
I_+5V 7 +5V supply current, open load
Uinmax -50 50 V maximum input applied voltage
Uin_Ilow >2.34 V digital modes output current low value
input voltage threashold
Uin_Ihi <1.56 V digital modes output current low value
input voltage threashold
Uin_Ian 0 10 V analog modes input voltage range to
linear output current transfer charac-
teristic
Rin 10 kOhm input resistance
Uoutmax -15 50 V maximum applied voltage to output
signal (=sink) or reference (=source)
pin
Uout_simin 0.7+Isi V minimum output signal pin (=sink)
nk*33R applied voltage for proper operation
of current regulation
Uout_somax 14.3- V maximum output reference pin
Isource (=source) applied voltage for proper
*33R operation of current regulation
Analog Mode Uin=0..10V -> Iout=0..25mA
Analog Modi- Uin=0..10V -> Iout=0..xxmA
fied Mode user defined, resistor changes neces-
sary
Digital Mode Uin<1.53V -> Iout=14mA
Uin>2.56V -> Iout=0mA
Digital Modi- Uin<1.53V -> Iout=hi-mA
fied Mode Uin>2.56V -> Iout=0mA
user defined, resistor changes neces-
sary
Digital Offset Uin<1.53V -> Iout=14mA
Mode Uin>2.56V -> Iout=7mA
Digital Offset Uin<1.53V -> Iout=hi-mA
Modified Mode Uin>2.56V -> Iout=lo-mA
user defined, resistor changes neces-
sary

Table 1: electrical data

dSPACE GmbH
8