COMMANDO 300

Technical Specification
05130-2
2005-05-25

APPLICATION
Commando 300 is a hydraulic, self-propelled drilling For easy operation, good visibility and operator
unit on a 4-wheel, oscillated drive carrier. It drills safety, Commando 300 is supplied with an electronic
holes with a maximum recommended diameter of 64 remote control unit. Thanks to the electronics, this
mm (2 ½") and a maximum practical length of 15 unit has fewer levers which make it easy to use. For
meters (50'), utilizing 25, 28 or 32 mm (1", 1 1/8" or 1 operator comfort Commando 300 is also equipped
1
/4") extension rods. with a dust collection system, which gathers drilling
Commando 300 is a completely self contained dust from the hole into a plastic bag.
drilling unit. It is easily maneuverable with good Typical applications for Commando 300 are
rough terrain capabilities. It is also easy to transport foundation drilling, road cutting, trenching,
between job sites on a truck or on a trailer, or it can occasional bolting and other special drilling
even be lifted by a helicopter. applications. Therefore Commando 300 is most often
Commando 300 is equipped with HL 300, hydraulic used by construction contractors, mines and
top hammer rock drill. The rock drill is mounted on quarries, and the municipal sector. Due to its
an aluminium chain feed, which is attached to an versatility Commando 300 is often included in the
articulated boom giving a drilling coverage of 10 m2 equipment fleet of rental houses as well.
(108 sq-ft). A 55 kW (73 hp) diesel engine supplies
power both for hydraulic pumps and for an on-board
compressor. Several routine functions of Commando
300, e.g. collaring and antijamming, are
automatically executed by electronic controls.

1/4
 COMMANDO 300
Technical Specification
05130-2
2005-05-25

COVERAGE AREA
Horizontal drilling, forwards
With manual roll-over
Vertical drilling
Vertical drilling

+/-47º
43º
43º

1m
1m

Horizontal drilling, sidewards Bolting

DIMENSIONS

5590

2580

260

2700 (max)
110º 1400 (min)
2970
3770
1200 (max)
0 (min)
2390

2280

3370

2/4
 COMMANDO 300
Technical Specification
05130-2
2005-05-25

HYDRAULIC ROCK DRILL HYDRAULIC SYSTEM

Rock drill type HL 300 Driving, boom and drilling Load sensing system
Drill rod diameters 32 mm (25, 28 mm) Rotation and dust Open center
Shank adapter Standard collector
Operating pressure 90-160 bar Filtration rate 10 micron abs.
Percussion rate 50 Hz Cooling capacity up to +40°C ambient
Percussion output power 8 kW Hydraulic oil tank 75 l
Maximum rotation torque 245 Nm (400 Nm)
/170 bar CONTROL SYSTEM
Shank lubrication Grease Driving and jack control Direct hydraulic
Flushing Air or water Boom and drillingcontrol Electric remote
Weight 94 kg Collaring control Automatic, adjustable
Percussion control Controlled by feed
pressure
CHAIN FEED Antijamming system Both feed and percussion
Chain feed type CF 300 x 12 are controlled by time
Length of feed 5 590 mm relays
Rock drill travel 4 070 mm Voltage 12 VDC
Max. length of starter rod 3 660 mm (12')
Hole length with starter 3 300 mm (10' 10") ARTICULATED BOOM
rod
Feed/pull out force 15 kN Boom type DB 300
Retaining centralizer Pito 9H Boom length 4m
Feed extension travel 1 300 mm Boom swing +/- 40°
Feed swing +/- 47° Vertic. drilling coverage 10 m2
on flat
Feed tilt 110°
Vertical collaring height +2.2 m/-4.6 m
Weight 245 kg
Horizontal holes Sideways, forwards

POWERPACK DUST COLLECTION SYSTEM

Engine type Deutz BF4L 2011/F, Dust collector type DC 410H
air/oil cooled Capacity/vacuum 10 m3/min at 950 mm
Number of cylinders 4 vacuum H2O
Engine output 55 kW/2800 rpm Filter elements/material 9 pcs/fiber
Transmission type Direct/v-belt Total filter surface 7.2 m2
Hydraulic pumps One variable displace- Hydraulic motor output 5.5 kW
ment, two gear pumps Weight 110 kg
Screw compressor type Enduro 12
Air flushing capacity 2.5 m3/min CARRIER
Flushing air pressure 4-8 bar Carrier type Rubber tyred,
Air cleaner 2 pcs 4-wheel drive
Fuel tank 100 l Oscillation angles +/- 16°
Average fuel consuption 8-10 l/h Ground clearance 380 mm
Max. operating altitude 3000 m Tramming force 31 kN
Fuel saving system Standard Tramming speed 4.5 km/h
Number of hydraulic jacks 4

3/4
 COMMANDO 300
Technical Specification
05130-2
2005-05-25

STANDARD COMPONENTS TRANSPORT DIMENSIONS

1. Rock drill HL 300, hydraulic Weight (without options) 5 000 kg
2. Chain feed CF 300 x 12/Pito 9H, incl. Width without tracks 2.3 m
one set of jaws Height 2.6 m
3. Rod rack For 2 extra rods on chain Total length 5.6 m
feed
4. Boom DB 300, articulated THE JAWS FOR DRILL STEELS
5. Carrier Rubber-tyred
Drill steel Drill steel Recommended
6. Powerpack Diesel driven, hydraulic type diameter hole diameter
pumps and on-board
Integral rod 22 mm
compressor 28 - 38 mm
1. for HEX 1
7. Hydraulic system Open center and load
7
/8" 1 7/64 - 1 ½"
drifter
sensing
Extension 25 mm 38 - 45 mm
8. Control system TA 342, electric 2.
rods 1" 1 ½" - 1 ¾"
9. Dust collection DC 410H, hydraulic
system Extension 28 mm 38 - 48 mm
3.
10. Working lights 4 pcs rods 1 1/8" 1 ½" - 1 7/8"
11. Hydraulic jacks 4 pcs Extension 32 mm 45 - 64 mm
4.
12. Manuals Service and spare rods 1 ¼" 1 ¾" - 2 ½"
parts manuals:
2 x paper copy If several jaws selected please specify jaws
2 x CD-ROM (Toolman) assembled.
13. EU-safety devices

SELECTION OF OPTIONS
1. HEX 1 rock drill (replaces standard component) 12. Hydraulic roll-over (360°) boom head
2. Hydraulic winch (2 tons) Specify the boom head dead point
3. Pulling device for 22 mm (7/8") rods - upwards
- 3 o'clock from front
4. Chain tracks
13. Bigger rotation motor (400 Nm) for 51 or
5. Hydraulic drill steel grinder, Dynaset 64 mm holes
6. Hydraulic drill steel grinder for integral steels, 14. PTX exhaust gas purifier
Sanroc ILH 15. Water flushing kit without water pump
7. Angle indicator MEC Angie
16. Water pump for water flushing kit
8. TIM 2104 Tamrock inclination angle measuring
and controlling system 17. Extra manuals
9. Electric filling pump for refuelling 18. First service kit for Commando 300,
10 Electric engine heater ID 881 536 39
19. Special tools for HL 300, field kit
11. Spirit level angle indicator
ID 881 537 69

www.tamrock.com
SANDVIK TAMROCK reserves the right to change this specification without further notice

SANDVIK TAMROCK OY, P.O.Box 100, FIN-33311 Tampere, FINLAND 4/4

Tel.int. +358 205 44 121, Telefax int. +358 205 44 120