REFER TO 1.

ALL DIMENSIONS ARE IN MILLIMETRES (mm) UNLESS NOTED

NOTE 10 NEW FLANGED THRUST FLANGE (THRUST
STUB FLANGE OTHERWISE.
PLAIN ENDED BLOCK OMITTED FOR
( WITH BACKING RING )
DI PIPE CLARITY, SEE STD-W-28)
2. ALL BENDS, TEES, DEAD ENDS, ETC. OF PIPELINES TO BE
NEW PE PIPE ADEQUATELY RESTRAINED BY THRUST BLOCKS AS PER DRAWING
FLOW No. STD-W-28. THRUST BLOCKS NOT SHOWN FOR CLARITY.

3. BUTT FUSION WELDING AND ELECTRO FUSION JOINTING OF PIPES

SHALL ONLY BE CARRIED OUT BY TRAINED OPERATIVES IN
FUSION EXISTING AC / CI / uPVC PIPE POSSESSION OF A CURRENT TRAINING CERTIFICATE, USING
WELD DISMANTLING SV STEPPED OR FULLY AUTOMATIC APPROVED JOINTING MACHINE/RIGS IN
JOINT FLEXIBLE COUPLING ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. THE
IDENTITY OF THE PE PIPELINE MANUFACTURER SHALL BE MADE
KNOWN TO IRISH WATER PRIOR TO COMMENCEMENT OF THE
INSTALLATION. CERTIFICATION AND TESTING (INCLUDING
INDEPENDENT THIRD PARTY CERTIFICATION) SHALL BE PROVIDED
REFER TO THRUST FLANGE (THRUST
STUB FLANGE CONCENTRIC TO CONFIRM QUALITY ASSURANCE COMPLIANCE. EACH JOINT
NOTE 10 BLOCK OMITTED FOR
( WITH BACKING RING ) TAPER SHALL BE CLEARLY MARKED WITH THE JOINT LOGGED
(IF REQUIRED) CLARITY, SEE STD-W-28) AUTOMATICALLY ON THE JOINTING MACHINE. A PRINTOUT OF THE
NEW PE PIPE JOINT DETAILS, WITH A GPS LOCATION OF EACH JOINT, SHALL BE
EXISTING AC / CI / uPVC PIPE
PROVIDED AND RETAINED FOR QUALITY ASSURANCE PURPOSES.
FLOW
4. CONNECTING TO EXISTING MAINS IS TO BE CARRIED OUT BY IRISH
WATER OR AN APPROVED IRISH WATER AGENT.

5. WHEN EXISTING AC WATERMAINS ARE PRESENT A SPECIFIC

FUSION
SV NEW FLANGED STEPPED OR METHOD STATEMENT SHALL BE SUBMITTED TO IRISH WATER PRIOR
WELD DISMANTLING
PLAIN ENDED FLEXIBLE COUPLING TO WORKS TAKING PLACE AND SUBJECT TO WRITTEN APPROVAL,
JOINT
DI PIPE DETAILING THE PROTECTION TO BE PUT IN PLACE TO EXISTING
MAINS, METHOD OF REMOVAL OF EXISTING AC, METHOD OF
DISPOSAL OF EXISTING AC AND METHOD OF CONNECTION TO
EXISTING AC.
REFER TO THRUST FLANGE (THRUST
NOTE 10 NEW FLANGED 6. PIPE MATERIAL REFERENCES AS FOLLOWS:
BLOCK OMITTED FOR
STUB FLANGE PLAIN ENDED AC - ASBESTOS CEMENT
CLARITY, SEE STD-W-28)
( WITH BACKING RING ) DI PIPE DI - DUCTILE IRON
CI - CAST IRON
EXISTING DI PIPE
NEW PE PIPE PE - POLYETHYLENE
FLOW uPVC - UNPLASTICISED POLY VINYL CHLORIDE
ST - STEEL
OTHER - REFERS TO ALL EXISTING PIPE MATERIALS OTHER THAN PE
(TYPICALL AC, DI, CI, uPVC & ST).
FUSION
WELD DISMANTLING SV CONCENTRIC LONG BODY
JOINT TAPER (IF REQUIRED) FLEXIBLE 7. SLUICE VALVE CHAMBERS TO BE IN ACCORDANCE WITH STD-W-14
COUPLING (DI) AND STD-W-15 (PE). CHAMBERS NOT SHOWN FOR CLARITY.

8. ALL THRUST FLANGES TO BE ADEQUATELY RESTRAINED BY

THRUST BLOCKS AS PER DRAWING No. STD-W-28. THRUST BLOCKS
NOT SHOWN FOR CLARITY.
REFER TO
NOTE 10 CONCENTRIC 9. A HIGH LEVEL OF HEALTH & SAFETY PROCEDURES IS REQUIRED
NEW FLANGED PLAIN
NEW FLANGED PLAIN TAPER (IF ENDED DI PIPE EXISTING AC / CI / WHEN WORKING ON AC MAINS, & THE OPERATION OF DISMANTLING/
ENDED DI PIPE REQUIRED) uPVC PIPE REMOVAL OF AC PIPES & JOINTS.
NEW DI PIPE 10. VALVES SHALL BE ARRANGED IN SUCH A MANNER TO ALLOW FOR
FLOW THE NETWORK TO BE MANAGED TO ENSURE THAT NO MORE THAN
40 PROPERTIES LOSE WATER FROM A BURST ON THE SYSTEM AT
ANY ONE TIME.

LONG BODY
FLEXIBLE COUPLING SV
DISMANTLING STEPPED OR
JOINT FLEXIBLE COUPLING
THRUST FLANGE (THRUST
BLOCK OMITTED FOR
CLARITY, SEE STD-W-28)

CONCENTRIC REFER TO
TAPER NOTE 10
NEW FLANGED PLAIN (IF REQUIRED) NEW FLANGED PLAIN
ENDED DI PIPE ENDED DI PIPE
NEW DI PIPE
EXISTING DI PIPE
FLOW

SV LONG BODY
LONG BODY DISMANTLING FLEXIBLE
FLEXIBLE JOINT COUPLING
COUPLING
THRUST FLANGE (THRUST
BLOCK OMITTED FOR
CLARITY, SEE STD-W-28)

REFER TO
STUB FLANGE CONCENTRIC NOTE 10 STUB FLANGE
(WITH BACKING RING) TAPER (WITH BACKING RING)
DISMANTLING
(IF REQUIRED)
JOINT
NEW PE PIPE
EXISTING PE PIPE

FUSION FUSION
SV WELD
WELD

REFER TO CONCENTRIC
NEW FLANGED PLAIN NOTE 10 TAPER STUB FLANGE
ENDED DI PIPE (IF REQUIRED) (WITH BACKING RING)

NEW DI PIPE

LONG BODY FUSION EXISTING PE PIPE

SV WELD
FLEXIBLE
COUPLING
THRUST FLANGE (THRUST
BLOCK OMITTED FOR
CLARITY, SEE STD-W-28)

REFER TO INDEX SHEET FOR NOTES REGARDING DESIGN RESPONSIBILITY & RISK ASSESSMENT
SCALE DATE
4 07/'20 RH TOC Dismantling joints relocated STANDARD DETAILS - WATER NOT TO SCALE SEPT. 2015
3 11/'17 JMC TOC TITLE DRAWING No. REV

2 08/'16 JMC TOC Added Note 9 GENERAL PIPE CONNECTIONS

1 04/'16 JMC TOC Added couplings (2 details) (Sheet 1 of 7)
0 09/'15 JMC TOC Initial Issue SL
No. Date Drn Chk Description App