LME49743

www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

LME49743 Quad High Performance, High Fidelity Audio Operational Amplifier

Check for Samples: LME49743

1FEATURES DESCRIPTION
•
2 Easily Drives 600Ω Loads The LME49743 is a low distortion, low noise, high
slew rate operational amplifier optimized and fully
• Optimized for Superior Audio Signal Fidelity specified for high performance, high fidelity
• Output Short Circuit Protection applications. The LME49743 audio operational
• 98dB (Typ) PSRR and 106dB (Typ) CMRR amplifier delivers superior audio signal amplification
for outstanding audio performance. The LME49743
• TSSOP Package
combines low voltage noise density (3.5nV/√Hz) and
THD+N (0.0001%) to easily satisfy demanding audio
APPLICATIONS applications. To ensure that the most challenging
• Audio Amplifiers and Preamplifiers loads are driven without compromise, the LME49743
has a slew rate of ±12V/μs and an output current
• Professional Audio
capability of ±21mA.
• Equalization and Crossover Networks
The LME49743's outstanding CMRR(106dB),
• Line Drivers and Receivers
PSRR(98dB), and VOS (±0.15mV) give the amplifier
• Active Filters excellent operational amplifier DC performance.
The LME49743 has a wide supply range of ±4.0V to
±17V. Over this supply range the LME49743’s input
circuitry maintains excellent common-mode, power
supply rejection, and low input bias current. The
LME49743 is unity gain stable.
The LME49743 is available in 14–lead TSSOP.

Table 1. Key Specifications

VALUE UNIT
Power Supply Voltage Range ±4.0V to ±17 V
THD+N (AV = 1, VOUT = 3VRMS, RL = 2kΩ 0.0001 % (typ)
fIN = 1kHz) RL = 600Ω 0.0001 % (typ)
nV/√Hz
Input Noise Density 3.5
(typ)
Slew Rate ±12 V/μs (typ)
Gain Bandwidth Product 30 MHz (typ)
Open Loop Gain (RL = 600Ω) 110 dB (typ)
Input Bias Current 190 nA (typ)
Input Offset Voltage ±0.15 mV (typ)

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2 All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2008–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

Connection Diagram

Figure 1. TSSOP Package

See Package Number PW0014A

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.

(1) (2) (3)

Absolute Maximum Ratings
Power Supply Voltage (VS = V+ - V-) 36V
Storage Temperature −65°C to 150°C
Input Voltage (V-) - 0.7V to (V+) + 0.7V
Output Short Circuit (4) Continuous
Power Dissipation Internally Limited
ESD Susceptibility (5) 750V
ESD Susceptibility (6) 175V
Junction Temperature 150°C
Thermal Resistance θJA (MT) 140°C/W
Temperature Range TMIN ≤ TA ≤ TMAX –40°C ≤ TA ≤ 85°C
Supply Voltage Range ±4.0V ≤ VS ≤ ± 17V

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) Operating Ratings indicate conditions for which the device is functional, but do not specify specific performance limits. For specifications
and test conditions, see the Electrical Characteristics. The specifications apply only for the test conditions listed. Some performance
characteristics may degrade when the device is not operated under the listed test conditions.
(3) If Military/Aerospace specifications are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(4) Amplifier output connected to GND, any number of amplifiers within a package.
(5) Human body model, 100pF discharged through a 1.5kΩ resistor.
(6) Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage and then
discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50Ω).

2 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

Electrical Characteristics
The following specifications apply for VS = ±15V, RL = 2kΩ, fIN = 1kHz, and TA = 25C, unless otherwise specified. (1) (2)
LME49743
Units
Parameter Test Conditions Limit
Typ (3) (4) (5)
(Limits)

AV = 1, VOUT = 3VRMS
THD+N Total Harmonic Distortion + Noise RL = 2kΩ 0.0001
RL = 600Ω 0.0001 0.0002 % (max)
AV = 1, VOUT = 3VRMS
IMD Intermodulation Distortion 0.0005 % (max)
Two-tone, 60Hz & 7kHz 4:1
GBWP Gain Bandwidth Product 30 25 MHz (min)
SR Slew Rate 12 9.5 V/μs (min)
VOUT = 1VP-P, –3dB
FPBW Full Power Bandwidth referenced to output magnitude 10 MHz
at f = 1kHz
AV = 1, 10V step, CL = 100pF
ts Settling time
0.1% error range 1.2 μs
Equivalent Input Noise Voltage fBW = 20Hz to 20kHz 0.48 0.65 μVRMS
en Equivalent Input Noise Density f = 1kHz 3.5 4.5 nV/√Hz (max)
f = 10Hz 6.4 nV/√Hz
f = 1kHz 1.6 pA/√Hz
in Current Noise Density
f = 10Hz 3.1 pA/√Hz
VOS Offset Voltage ±0.15 ±1.0 mV (max)
Average Input Offset Voltage Drift vs
ΔVOS/ΔTemp 40°C ≤ TA ≤ 85°C 0.05 μV/°C
Temperature
Average Input Offset Voltage Shift vs
PSRR ΔVS = 20V (6) 98 94 dB (min)
Power Supply Voltage
fIN = 1kHz 118 dB
ISOCH-CH Channel-to-Channel Isolation
fIN = 20kHz 112 dB
IB Input Bias Current VCM = 0V 190 250 nA (max)
Input Bias Current Drift vs
ΔIOS/ΔTemp –40°C ≤ TA ≤ 85°C 0.05 nA/°C
Temperature
IOS Input Offset Current VCM = 0V 7 40 nA (max)
(V+)–2.0 V (min)
VIN-CM Common-Mode Input Voltage Range ±13.2
(V-)+2.0 V (min)
CMRR Common-Mode Rejection –10V<VCM<10V 106 98 dB (min)
Differential Input Impedance 30 kΩ
ZIN
Common Mode Input Impedance –10V<VCM<10V 1000 MΩ
–10V<VOUT<10V, RL = 600Ω 110 dB (min)
AVOL Open Loop Voltage Gain –10V<VOUT<10V, RL = 2kΩ 110 dB (min)
–10V<VOUT<10V, RL = 10kΩ 110 100 dB (min)
RL = 600Ω ±12.4 ±12.0 V (min)
VOUTMAX Maximum Output Voltage Swing RL = 2kΩ ±13.0 V (min)
RL = 10kΩ ±13.0 V (min)
IOUT Output Current RL = 600Ω, VS = ±17V ±21 ±20 mA (min)
+30 mA
IOUT-CC Short Circuit Current
–38 mA

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) Operating Ratings indicate conditions for which the device is functional, but do not specify specific performance limits. For specifications
and test conditions, see the Electrical Characteristics. The specifications apply only for the test conditions listed. Some performance
characteristics may degrade when the device is not operated under the listed test conditions.
(3) Typical specifications are specified at +25ºC and represent the most likely parametric norm.
(4) Tested limits are ensured to Texas Instrument's AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are specified by design, test, or statistical analysis.
(6) PSRR is measured as follows: VOS is measured at two supply voltages, ±5V and ±15V. PSRR = |20log(ΔVOS/ΔVS)|.
Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

Electrical Characteristics (continued)

The following specifications apply for VS = ±15V, RL = 2kΩ, fIN = 1kHz, and TA = 25C, unless otherwise specified.(1)(2)
LME49743
Units
Parameter Test Conditions Limit
Typ (3) (4) (5)
(Limits)

fIN = 10kHz
ROUT Output Impedance Closed-Loop 0.01 Ω
Open-Loop 13 Ω
CLOAD Capacitive Load Drive Overshoot 100pF 16 %
IS Total Quiescent Current IOUT = 0mA 10 14 mA (max)

4 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

Typical Performance Characteristics

THD+N THD+N
vs vs
Output Voltage Output Voltage
VS = ±15V, RL = 2kΩ, f = 1kHz VS = ±15V, RL = 10kΩ, f = 1kHz
30kHz BW 30kHz BW

Figure 2. Figure 3.

THD+N THD+N
vs vs
Output Voltage Frequency
VS = ±15V, RL = 600Ω, f = 1kHz VS = ±15V, VOUT = 3VRMS, RL = 2kΩ
30kHz BW 80kHz BW

Figure 4. Figure 5.

THD+N THD+N
vs vs
Frequency Frequency
VS = ±15V, VOUT = 3VRMS, RL = 10kΩ VS = ±15V, VOUT = 3VRMS, RL = 600Ω
80kHz BW 80kHz BW

Figure 6. Figure 7.

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 5

Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

Typical Performance Characteristics (continued)

+PSRR +PSRR
vs vs
Frequency Frequency
VS = ±15V, RL = 2kΩ, VRIPPLE = 200mVPP VS = ±15V, RL = 10kΩ, VRIPPLE = 200mVPP

Figure 8. Figure 9.

+PSRR −PSRR
vs vs
Frequency Frequency
VS = ±15V, RL = 600Ω, VRIPPLE = 200mVPP VS = ±15V, RL = 2kΩ, VRIPPLE = 200mVPP

Figure 10. Figure 11.

−PSRR −PSRR
vs vs
Frequency Frequency
VS = ±15V, RL = 10kΩ, VRIPPLE = 200mVPP VS = ±15V, RL = 600Ω, VRIPPLE = 200mVPP

Figure 12. Figure 13.

6 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

Typical Performance Characteristics (continued)

CMRR CMRR
vs vs
Frequency Frequency
VS = ±15V, RL = 2kΩ, VIN = 200mVPP VS = ±15V, RL = 10kΩ, VIN = 200mVPP
+0 +0
-10 -10
-20 -20
-30 -30
-40 -40

CMRR (dB)
CMRR (dB)

-50 -50
-60 -60
-70 -70
-80 -80
-90 -90
-100 -100
-110 -110
-120 -120
10 100 1k 10k 100k 10 100 1k 10k 100k

FREQUENCY (Hz) FREQUENCY (Hz)

Figure 14. Figure 15.

CMRR Crosstalk
vs vs
Frequency Frequency
VS = ±15V, RL = 600Ω, VIN = 200mVPP VS = ±15V, VOUT = 3VRMS, RL = 2kΩ
+0
-10
-20
-30
-40
CMRR (dB)

-50
-60
-70
-80
-90
-100
-110
-120
10 100 1k 10k 100k

FREQUENCY (Hz)
Figure 16. Figure 17.

Crosstalk Crosstalk
vs vs
Frequency Frequency
VS = ±15V, VOUT = 3VRMS, RL = 10kΩ VS = ±15V, VOUT = 3VRMS, RL = 600Ω

Figure 18. Figure 19.

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 7

Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

Typical Performance Characteristics (continued)

IMD IMD
vs vs
Output Voltage Output Voltage
VS = ±5V, RL = 2kΩ VS = ±5V, RL = 10kΩ
7kHz/60Hz 4:1 SMPTE 7kHz/60Hz 4:1 SMPTE

Figure 20. Figure 21.

IMD
vs Output Voltage
Output Voltage vs
VS = ±5V, RL = 600Ω Supply Voltage
7kHz/60Hz 4:1 SMPTE RL = 2kΩ, THD+N = 0.1%
12

OUTPUT VOLTAGE (VRMS) 10

0
4 6 8 10 12 14 16 18

SUPPLY VOLTAGE (±V)

Figure 22. Figure 23.

Output Voltage Output Voltage

vs vs
Supply Voltage Supply Voltage
RL = 10kΩ, THD+N = 0.1% RL = 600Ω, THD+N = 0.1%
12 12

10 10
OUTPUT VOLTAGE (VRMS)
OUTPUT VOLTAGE (VRMS)

8 8

6 6

4 4

2 2

0 0
4 6 8 10 12 14 16 18 4 6 8 10 12 14 16 18
SUPPLY VOLTAGE (±V) SUPPLY VOLTAGE (±V)

Figure 24. Figure 25.

8 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

Typical Performance Characteristics (continued)

Supply Current
vs Scope Photo
Supply Voltage Small Signal

Figure 26. Figure 27.

Scope Photo Scope Photo

Large Signal, Non-Inverting Large Signal, Inverting

Figure 28. Figure 29.

Equivalent Input Noise

vs
Frequency Power Bandwidth
10
EQUIVALENT INPUT NOISE

5
VOLTAGE (nV/ Hz)

1
10 100 1k 10k 100k
FREQUENCY (Hz)
Figure 30. Figure 31.

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 9

Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

Typical Performance Characteristics (continued)

Open Loop Gain and Phase
vs Frequency

Figure 32.

10 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

APPLICATION INFORMATION

DISTORTION MEASUREMENTS
The vanishingly low residual distortion produced by LME49743 is below the capabilities of all commercially
available equipment. This makes distortion measurements just slightly more difficult than simply connecting a
distortion meter to the amplifier’s inputs and outputs. The solution, however, is quite simple: an additional
resistor. Adding this resistor extends the resolution of the distortion measurement equipment.
The LME49743’s low residual distortion is an input referred internal error. As shown in Figure 33, adding the 10Ω
resistor connected between the amplifier’s inverting and non-inverting inputs changes the amplifier’s noise gain.
The result is that the error signal (distortion) is amplified by a factor of 101. Although the amplifier’s closed-loop
gain is unaltered, the feedback available to correct distortion errors is reduced by 101, which means that
measurement resolution increases by 101. To ensure minimum effects on distortion measurements, keep the
value of R1 low as shown in Figure 33.
This technique is verified by duplicating the measurements with high closed loop gain and/or making the
measurements at high frequencies. Doing so produces distortion components that are within the measurement
equipment’s capabilities. This datasheet’s THD+N and IMD values were generated using the above described
circuit connected to an Audio Precision System Two Cascade.
R2
1000:

R1 LME49743
10: Distortion Signal Gain = 1+(R2/R1)

Generator Output Analyzer Input

Audio Precision
System Two
Cascade

Actual Distortion = AP Value/100

Figure 33. THD+N and IMD Distortion Test Circuit

Application Hints
The LME49743 is a high speed op amp with excellent phase margin and stability. Capacitive loads up to 100pF
will cause little change in the phase characteristics of the amplifiers and are therefore allowable.
Capacitive loads greater than 100pF must be isolated from the output. The most straightforward way to do this is
to put a resistor in series with the output. This resistor will also prevent excess power dissipation if the output is
accidentally shorted.

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 11

Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

Noise Measurement Circuit

+VCC -VEE

+
47 PF 47 PF
+

V1 + 0.47 PF

390
LME49743
V2
+ 0.47 PF

- 39k + 4.7 PF
+
15 nF 4.7 nF - 39k
VO

- AVERAGE RESPONDING
99k
AC VOLT METER
200k 16k 99k
1k 27 pF

390 1k 27 pF

RIAA PREAMP FLAT AMP. 40 dB + 40 dB

35 dB, f = 1 kHz

(1) Complete shielding is required to prevent induced pick up from external sources. Always check with oscilloscope for
power line noise.
(2) Total Gain: 115 dB at f = 1 kHz
(3) Input Referred Noise Voltage: en = VO/560,000 (V)

Figure 34.

RIAA Preamp Voltage Gain,

RIAA Deviation Flat Amp Voltage Gain
vs vs
Frequency Frequency
VIN = 10mV, AV = 35.0dB, f = 1kHz VO = 0dB, AV = 80.0dB, f = 1kHz

50 90
VOLTAGE GAIN (dB)

40 80
VOLTAGE GAIN (dB)

30 70

20 60

10 50
0
DEVIATION (dB)

40
+1
RIAA

30
0
20
-1
20 100 1k 10k 20k 10 100 1k 10k 100k
FREQUENCY (Hz) FREQUENCY (Hz)

Figure 35. Figure 36.

12 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

Typical Applications

R2

C1 C1
0.01 PF 0.01 PF
R2 R1 R1

- - -
1 VHP 1 VBP 1 VLP
RG 4 LME49743 4 LME49743 4 LME49743
VIN + + +

R0 R2

Figure 37. State Variable Filter

C1
R5
20k 10 PF

R2 R3 R4
20k 10k 20k

R1
20k D1
VIN - 1S1588 -
1 1
VO = |VIN|
4 LME49743 4 LME49743
+ D2 +
1S1588
R6
R7
15k
6.2k

Figure 38. AC-DC Converter

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 13

Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

3.41R1
51k

R1 R1
15k 15k
-
1
4 LME49743 VO1

VI 0.707R1
10k

-
R1 R1 1 VO2
4 LME49743
15k 15k
+

3.41R1
51k

Figure 39. 2 Channel Panning Circuit (Pan Pot)

R2

VCC

R1 R3
- 10k
VI
1 LME49743 Q1
4
+ R9 R7
10k 33
VO
R8
R5 33
10k
BIAS
Q2

R6
10k
-VEE

Figure 40. Line Driver

14 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

BOOST BASS CUT

R1 R2 R1
VI
C1 C1
0.05 PF 0.05 PF

R3
-
C2 1
0.005 PF 4 LME49743 VO

R5 R5 +

R4
BOOST TREBLE CUT

Figure 41. Tone Control

33 PF
+ 470
10 PF
1
400 pF
47k 4 LME49743
Phono
Cartridge - 100k

16k 200k

390 4.7 nF 15 nF

100 PF

Av = 35 dB
En = 0.33 μV
S/N = 90 dB
f = 1 kHz
A Weighted
A Weighted, VIN = 10 mV
at f = 1 kHz

Figure 42. RIAA Preamp

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

VI + R3 R4
10k 10k
1
4 LME49743
R
-
R2
10k -
1 VO
R1 R5 4 LME49743
200 10k +

- R6 R7
10k 10k
1
4 LME49743
V2 +

Illustration is:
V0 = 101(V2 − V1)

Figure 43. Balanced Input Mic Amp

CUT 20k BOOST

f01

f02
C2
R2 +
3k f03 1
4 LME49743 VO
VI
C1
f04 -
+
1 f05 3k
4 LME49743
R1
- f06

f07

f08

f09

f010

Figure 44. 10 Band Graphic Equalizer

16 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 LME49743
www.ti.com SNAS442B – MARCH 2008 – REVISED APRIL 2013

fo (Hz) C1 C2 R1 R2
32 0.12μF 4.7μF 75kΩ 500Ω
64 0.056μF 3.3μF 68kΩ 510Ω
125 0.033μF 1.5μF 62kΩ 510Ω
250 0.015μF 0.82μF 68kΩ 470Ω
500 8200pF 0.39μF 62kΩ 470Ω
1k 3900pF 0.22μF 68kΩ 470Ω
2k 2000pF 0.1μF 68kΩ 470Ω
4k 1100pF 0.056μF 62kΩ 470Ω
8k 510pF 0.022μF 68kΩ 510Ω
16k 330pF 0.012μF 51kΩ 510Ω

NOTE
At volume of change = ±12 dB
Q = 1.7

Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 17

Product Folder Links: LME49743
LME49743
SNAS442B – MARCH 2008 – REVISED APRIL 2013 www.ti.com

REVISION HISTORY
Rev Date Description
1.0 03/26/08 Initial release.
1.01 01/12/09 Fixed a typo.
B 04/04/13 Changed layout of National Data Sheet to TI format.

18 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated

Product Folder Links: LME49743

 PACKAGE OPTION ADDENDUM

www.ti.com 10-Dec-2020

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead finish/ MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) Ball material (3) (4/5)
(6)

LME49743MTX/NOPB ACTIVE TSSOP PW 14 2500 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM -40 to 85 L49743
MT

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 9-Mar-2018

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LME49743MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 9-Mar-2018

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LME49743MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0

Pack Materials-Page 2
 IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated