Accutrim 1240 (RJ26 Style)

Vishay Foil Resistors

Bulk Metal Foil Technology Ultra High Precision Trimming Potentiometers, 1/ " Square, RJ26 Style, Designed to Meet or Exceed The Requirements of 4 MIL-PRF-39035, Char. H with a Smooth and Unidirectional Output
Temperature coefficient of resistance (TCR): 10 ppm/C. (- 55 C to + 150 C ref. at + 25 C); through the wiper (3); 25 ppm/C (see table 2 for low values) A smooth and unidirectional resistance with leadscrew adjustment Load life stability: 0.1 % typical R, 1.0 % maximum R under full rated power at + 85 C for 10 000 h Settability: 0.05 % typical; 0.1 % maximum Setting stability: 0.1 % typical; 0.5 % maximum, DSS Power rating: 0.25 W at + 85 C Resistance range: 5 to 10 k Tolerance: 5 %, 10 % Electrostatic discharge (ESD) up to 25 000 V Terminal finish: gold plated (tin/lead finish is available on request)

FEATURES

1240P

1240W

1240X

INTRODUCTION
Vishay Foil precision trimmers have the Bulk Metal Foil resistive element which possesses a unique inherent temperature and load life stability. Plus, their advanced virtually back lash-free adjustment mechanism makes them easy to set quickly and accurately and keeps the setting exactly on target.

Resistance

Resistance

BULK METAL FOIL

WIREWOUND

Resistance

CERMET

Wiper Travel

Wiper Travel

Wiper Travel

TABLE 1 - MODEL SELECTION

MODEL 1240 TERMINATION STYLE W-edge mount, top adjust X-edge mount, side adjust P-horizontal mount, side adjust AVERAGE WEIGHT (g) 0.4 POWER RATING at + 85 C AMBIENT 0.25 W NO. OF TURNS 21 2

Note See Figure 1, next page

TABLE 2 - 1240 (RJ26) SERIES ELECTRICAL SPECIFICATIONS

Temperature Coefficient of Resistance (TCR) 50 to 10 k End-to-end (2) Temperature Coefficient of Resistance 5, 10 and 20 Through the wiper (3) Stability Load life at 10 000 h End-to-end (2) Power Rating (4) Settability Setting Stability Contact Resistance Variation - CRV (noise) (5) Hop-off High-Frequency Operation Rise time Inductance Capacitance Operating Temperature Range Document Number: 63053 Revision: 23-Mar-10 10 ppm/C maximum (- 55 C to + 150 C, + 25 C ref.) 20 ppm/C 25 ppm/C 0.1 % typical R 1.0 % maximum R (under full rated power of 0.25 W at + 85 C) 0.25 W at + 85 C 0.05 % typical; 0.1 % maximum 0.1 % typical; 0.5 % maximum 3 typical; 10 maximum 0.25 % typical; 1.0 % maximum 1.0 ns without ringing 0.08 H typical 0.5 pF typical - 55 C to + 150 C

TABLE 3 - VALUES VS. TOLERANCES

STANDARD RESISTANCE VALUES (in ) 5, 10 20, 50, 100, 200, 500, 1K, 2K, 5K, 10K STANDARD TOLERANCE 10 % 5%

TABLE 4 - MECHANICAL SPECIFICATIONS

Adjustment Turns Mechanical Stops Internal Terminations Case Material Shaft Torque Backlash 21 2 Wiper idles - no discontinuity All welded - no flux 1240X - diallyl-phthalate: green (DAP) 1240W - diallyl-phthalate: green (DAP) 1240P - thermoplastic: black 3 oz. in. maximum 0.005 % typical www.foilresistors.com 1

For any questions, contact: [email protected]

Accutrim 1240 (RJ26 Style)

Vishay Foil Resistors

FIGURE 1 - SCHEMATIC AND DIMENSIONS in Inches (Millimeters)

1240X
0.040" (1.02 mm) C

1240W
0.050" (1.27 mm) C 0.040" (1.02 mm) C

VISHAY

0.250" (6.35 mm) D VISHAY 1 CW 1 2 3 0.050" (1.27 mm) C 0.050" (1.27 mm) C 0.100" (2.54 mm) A 0.050" (1.27 mm) C 0.100" (2.54 mm) A 0.125" (3.18 mm) C (bottom view)
0.100" (2.54 mm) A 0.010" (0.25 mm) A 0.050" (1.27 mm) C 0.100" (2.54 mm) A

0.250" (6.35 mm) D

2 CW 3 1

0.250" (6.35 mm) D

0.250" (6.35 mm) D

0.175" (4.45 mm) C

0.175" (4.45 mm) C 0.050" (1.27 mm) C

0.125" (3.18 mm) C (bottom view)

1240P
0.050" (1.27 mm) C VISHAY 0.175" (4.45 mm) C 1 CW 3

TOLERANCES: A = 0.005" (0.13 mm) C = 0.010" (0.25 mm) D = 0.020" (0.51 mm)

STANDARD MARKING: Model No. Date Code Resistance Value Tolerance

3 0.055" (1.40 mm) C 0.035" (0.89 mm) C

0.250" (6.35mm) D 0.016" (0.41 mm) A Resistance Value Tolerance

NOTES: Adjustment screw 0.080" (2.03 mm) diameter with 0.025" (0.64 mm) X 0.030" (0.76 mm) slot. Tolerance on

0.100" (2.54 mm) A 0.250" (6.35 mm) D 0.125" (3.18 mm) C

screw dimensions is 0.005" (0.13 mm). Model 1240 has gold plated terminal pins 0.016" (0.41 mm) 0.001" (0.03 mm) diameter, 0.200" (5.08 mm) length minimum.

0.100" (2.54 mm) A

Model No. Date Code

FIGURE 2 - POWER DERATING CURVE

FIGURE 3 - 1240W 10 k LOAD LIFE, 20 UNITS, 10 000 h at 0.25 W, + 85 C (Wiper at CW)

+ 2000

Percent of Rated Power

+ 100 + 75 + 50 + 25 0 - 75

+ 85 C

+ 1500 + 1000

R/R (ppm)
- 50 - 25 0 + 25 + 50 + 75 + 100 + 125 + 150 + 175

+ 500 0 - 500

- 1000 - 1500 - 2000 0 2000 4000 6000 8000 10 000

Ambient Temperature C

Time (h)

www.foilresistors.com 2

For any questions, contact: [email protected]

Document Number: 63053 Revision: 23-Mar-10

Accutrim 1240 (RJ26 Style)

Vishay Foil Resistors

TABLE 5 - COMPARISON
MIL-PRF-39035/3 CHARACTERISTIC H (6) TEST GROUP I Conditioning Contact resistance variation - CRV (noise) Immersion TEST GROUP I a Visual and mechanical Actual effective electrical travel End resistance Dielectric withstanding voltage - DWV Per MIL-STD-202, methods 301 and 105 Atmospheric pressure Barometric pressure Insulation resistance Shaft torque Thermal shock Setting stability TEST GROUP II Solderability TEST GROUP III Resistance temperature characteristic - TCR Moisture resistance Contact resistance variation - CRV (noise) TEST GROUP IV Settability Shock Setting stability Vibration Setting stability Contact resistance variation - CRV (noise) Salt spray TEST GROUP V Solder heat Low-temperature operation Setting stability Low-temperature storage High-temperature exposure Setting stability Contact resistance variation - CRV (noise) Integrity of shaft TEST GROUP VI Rotational life (200 cycles) Contact resistance variation - CRV (noise) Terminal strength TEST GROUP VII Life (2000 h) at + 85 C Life (10 000 h) at + 85 C TEST GROUP VIII Solvent resistance 1.0 % 3.0 % or 3 (7) No continuous stream of bubbles No failures 10 to 25 turns 2 % or 2 (7) MODEL 1240 MAXIMUM 0.5 % 3 typical, 10 maximum No continuous stream of bubbles No failures 21 2 turns 2 for values 1 k; 5 for values 2 k; 600 VAC, 1 min 250 VAC, 1 min > 1000 M 3 oz. in. maximum 0.5 % 0.5 % Per MIL-STD-202, method 208 0.001 %/C ( 10 ppm/C) 0.5 % 3 typical, 10 maximum 0.1 % 0.5 % 0.5 % 0.5 % 0.5 % 3 typical, 10 maximum No corrosion 0.1 % 0.5 % 0.5 % 0.5 % 0.5 % 0.5 % 3 typical, 10 maximum No loosening or breakage 2.0 % 3 typical, 10 maximum 2 lbs. 0.1 % typical, 1.0 % maximum 0.1 % typical, 1.0 % maximum No failures

600 VAC, 1 min 250 VAC, 1 min 1000 M 3 oz. in. maximum 1.0 % 1.0 % Per MIL-STD-202, method 208 0.005 %/C ( 50 ppm/C) 1.0 % 3.0 % or 3 (7) 1.0 % 1.0 % 1.0 % 1.0 % 1.0 % 3.0 % or 3 (7) No corrosion 1.0 % 1.0 % 2.0 % 1.0 % 3.0 % 2.0 % 3 % or 3 (7) No loosening or breakage 2.0 % 3 % or 3 (7) 2 lbs. 3.0 % 5.0 % No failures

Notes (1) Maximum is 1.0 % A.Q.L. standard for all specifications except TCR. (For TCR information, see notes 2 and 3.) (2) Maximum TCR applies to the 3 (sigma) limit or 99.73 % of a production lot. (Measured end-to-end with wiper off the element.) (3) Measurements of TCR through the wiper are influenced more by setting stability and the percentage of the total resistance in use (at the wiper) than by fundamental resistance change due to temperature alone. The parameter shown in table 2 is a 2 s distribution typifying the behavior of the device when used with 40 % or more of the total resistance in use. (4) Derated linearly for full power at + 85 C to zero power at + 150 C. See Figure 2 on previous page. (5) Independent of resistance value. 3 maximum available on special request. (6) All Rs are measured to the tolerance specified + 0.01 . (7) Whichever is greater. Special Available Options: Special marking Burn-in and screening operations. Document Number: 63053 Revision: 23-Mar-10

VISHAY TRIMMERS ARE INSPECTED 100 % for: Immersion Resistance tolerance check End resistance Visual-mechanical Dynamic tests for continuity, CRV By sample for: TCR DWV

For any questions, contact: [email protected]

www.foilresistors.com 3

Accutrim 1240 (RJ26 Style)

Vishay Foil Resistors

TABLE 6 - GLOBAL PART NUMBER INFORMATION

NEW GLOBAL PART NUMBER: Y4053500R000J0L (preferred part number format) DENOTES PRECISION Y VALUE R= K = k CHARACTERISTICS (1) 0 = gold plated termination (lead (Pb)-free) 1 to 999 = custom

0
TOLERANCE J =5% K = 10 %

PRODUCT CODE 4053 = 1240W 5053 = 1240X 0053 = 1240P

PACKAGING L = foam/box pack

FOR EXAMPLE: ABOVE GLOBAL ORDER Y4053 500R000 J 0 L: TYPE: 1240W VALUE: 500.0 ABSOLUTE TOLERANCE: 5.0 % TERMINATION: gold plated termination (lead (Pb)-free) PACKAGING: foam/box pack HISTORICAL PART NUMBER: 1240W 500R00 J B (will continue to be used) 1240W MODEL 1240W 1240X 1240P Note
(1)

500R00 RESISTANCE VALUE 500R00 = 500.0

J TOLERANCE J =5% K = 10 %

B PACKAGING B = foam/box pack

For non-standard requests, please contact application engineering.

www.foilresistors.com 4

For any questions, contact: [email protected]

Document Number: 63053 Revision: 23-Mar-10

Legal Disclaimer Notice

Vishay Precision Group

Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay Precision Group), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. The product specifications do not expand or otherwise modify Vishay Precision Groups terms and conditions of purchase, including but not limited to, the warranty expressed therein. Vishay Precision Group makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase. To the maximum extent permitted by applicable law, Vishay Precision Group disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Information provided in datasheets and/or specifications may vary from actual results in different applications and performance may vary over time. Statements regarding the suitability of products for certain types of applications are based on Vishay Precision Groups knowledge of typical requirements that are often placed on Vishay Precision Group products. It is the customers responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any conduct of Vishay Precision Group. The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay Precision Group products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay Precision Group for any damages arising or resulting from such use or sale. Please contact authorized Vishay Precision Group personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners.

Document No.: 63999 Revision: 27-Apr-11

www.vishaypg.com 1