Participant ID 131320000001

Participant Name CHINMAYA KUMAR MAHANTY

Test Center Name iON Digital Zone iDZ 1 Patia
Test Date 28/11/2022
Test Time 5:00 PM - 7:00 PM
Subject Wireman Trainee

Section : Respective Discipline syllabus

Q.1 Which of the following is NOT an SI unit?

Ans 1. Newton

2. Coulomb

3. Ampere

4. Calorie

Question ID : 9744434536
Status : Answered
Chosen Option : 4

Q.2 Which of the following motors should always be started with load?
Ans 1. DC differentially compounded motor

2. DC cumulatively compounded motor

3. DC shunt motor

4. DC series motor

Question ID : 9744434591
Status : Answered
Chosen Option : 4

Q.3 A joint made between copper conductors with central GI wire is:
Ans 1. T-joint

2. married joint

3. telephone joint

4. Britannia joint

Question ID : 9744434539
Status : Answered
Chosen Option : 2
Q.4 The current through the which of the following elements will NOT change instantaneously?
Ans 1. Fuse wire

2. Resistor

3. Capacitor

4. Inductor

Question ID : 9744434547
Status : Answered
Chosen Option : 4

Q.5 An installation comprising six circuits has individual insulation resistances of 2.5, 8, 200, 200,
200 and 200 Mega Ohms and therefore the total insulation resistance will be:
Ans 1. 1.83 Mega Ohms

2. 200 Mega Ohms

3. 2 Mega Ohms

4. 20 Mega Ohms

Question ID : 9744434579
Status : Answered
Chosen Option : 1

Q.6 An advantage of PMMC meter is:

Ans 1. cost is lower than moving iron instruments

2. the power consumption is low

3. it can be used for both AC and DC

4. the scale is logarithmical

Question ID : 9744434555
Status : Answered
Chosen Option : 2

Q.7 An ammeter, if necessary, can be used to find voltage by:

Ans 1. connecting in series after changing the current scale to voltage scale

2. connecting in parallel with a high resistance in series

3. reversing the polarities and connecting in parallel

4. connecting in parallel with a low resistance in series

Question ID : 9744434567
Status : Answered
Chosen Option : 2

Q.8 Rotor resistance starter is compatible for:

Ans 1. 3-phase slip ring induction motor

2. 3-phase squirrel cage induction motor

3. 1-phase induction motor

4. synchronous motor

Question ID : 9744434593
Status : Answered
Chosen Option : 1
Q.9 Western Union splice joint is generally for:
Ans 1. joining two aluminium conductors

2. extending the cable length

3. terminating the cable with transformer

4. tapping from cables

Question ID : 9744434537
Status : Answered
Chosen Option : 2

Q.10 The most common precaution taken to control risks is:

Ans 1. manual handling

2. use of safe systems of work

3. trips and falls

4. slips and falls

Question ID : 9744434557
Status : Answered
Chosen Option : 2

Q.11 HVDC is preferred for long distance power transmission on account of:
Ans 1. no harmonic problems

2. less cost for HVDC terminal

3. less power loss

4. simple protection

Question ID : 9744434529
Status : Answered
Chosen Option : 3

Q.12 As the cell discharges:

Ans 1. the specific gravity of the electrolyte remains the same

2. the specific gravity of the electrolyte reduces

3. the volume of the electrolyte reduces

4. the volume of the electrolyte remains the same

Question ID : 9744434562
Status : Answered
Chosen Option : 2

Q.13 Electrical installations shall be inspected and tested by competent authority prescribed by
the government at intervals NOT exceeding:
Ans 1. 2 years

2. 5 years

3. 1 year

4. 4 years

Question ID : 9744434518
Status : Answered
Chosen Option : 2
Q.14 Heat moving from one end of a metal fireplace poker to the other end is an example of heat
transfer by:
Ans 1. radiation

2. induction

3. conduction

4. convection

Question ID : 9744434533
Status : Answered
Chosen Option : 3

Q.15 The speed of the operation of protection depends on:

Ans 1. the frequency of the supply voltage

2. earth loop impedance

3. the phase angular difference between the fault current and voltage

4. the phase angular difference between the normal current and voltage

Question ID : 9744434572
Status : Answered
Chosen Option : 3

Q.16 In circuit breakers the contact resistance is less affected by:

Ans 1. the contamination on the contacts

2. the physical force on the contacts

3. the ambient temperature

4. the shape of the contact faces

Question ID : 9744434574
Status : Answered
Chosen Option : 3

Q.17 A merit of plate earthing over pipe earthing is:

Ans 1. that it can carry greater current

2. that it can be installed easily

3. that the contact surface area with earth is greater

4. that it is suitable for high power machines

Question ID : 9744434570
Status : Answered
Chosen Option : 3

Q.18 The total clearing time for a high speed circuit breakers is:
Ans 1. 10-20 cycles

2. 20-30 cycles

3. 1-2 cycles

4. about 50 cycles

Question ID : 9744434578
Status : Answered
Chosen Option : 3
Q.19 The charging current of a 100 Ampere-hour battery would be:
Ans 1. 1-2 A

2. 20-25 A

3. 10-12 A

4. 5-6 A

Question ID : 9744434563
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.20 The rating of the switch to control a 10 A rated discharge lighting should be:
Ans 1. equal to or greater than 20 A

2. equal to or greater than 15 A

3. equal to 10 A

4. equal to or greater than 10 A

Question ID : 9744434586
Status : Answered
Chosen Option : 4

Q.21 If a soldering iron draws 0.75 A at 120 V, then what is its resistance?
Ans 1. 160 Ohms

2. 80 Ohms

3. 90 Ohms

4. 45 Ohms

Question ID : 9744434542
Status : Answered
Chosen Option : 1

Q.22 Which of the following is a clean source for electricity generation?

Ans 1. Nuclear

2. Geo-thermal

3. Bio-gas

4. Wind

Question ID : 9744434522
Status : Answered
Chosen Option : 4

Q.23 The depolarising agent in cells is used to:

Ans 1. keep the electrolyte fluidic

2. remove hydrogen bubbles around the carbon rod

3. remove oxygen in the electrolyte

4. keep the chemical qualities of the electrolyte

Question ID : 9744434559
Status : Answered
Chosen Option : 2
Q.24 In the capacitor:
Ans 1. voltage leads the current

2. current leads the voltage

3. current and voltage are exactly out of phase

4. current and voltage are in phase

Question ID : 9744434525
Status : Answered
Chosen Option : 2

Q.25 Name the scientist who discovered that pure water has a fixed boiling and freezing
temperature.
Ans 1. Daniel Fahrenheit

2. Anders Celsius

3. John Dalton

4. Antoine Lavoisier

Question ID : 9744434531
Status : Answered
Chosen Option : 2

Q.26 Supplementary protective bonding conductors are for:

Ans 1. bonding exposed metal parts

2. for bonding structural steel works

3. for bonding sinks, baths and taps

4. for bonding main incoming services

Question ID : 9744434569
Status : Not Answered
Chosen Option : --

Q.27 The mechanical power developed in DC motor:

Ans 1. decreases with increase in back EMF when running below rated speed

2. increases with increase in back EMF

3. increases with decrease in back EMF

4. is independent of back EMF

Question ID : 9744434589
Status : Answered
Chosen Option : 2

Q.28 Interconnector in the ring distribution networks:

Ans 1. increases the power factor

2. increases the current to the consumer

3. increases the frequency of the supply

4. increases the voltages for the consumer

Question ID : 9744434524
Status : Answered
Chosen Option : 3
Q.29 The cables suspended from the transmission towers of the National Grid network are made
from:
Ans 1. copper and brass

2. copper with PVC insulation

3. aluminium and steel

4. aluminium and porcelain

Question ID : 9744434558
Status : Answered
Chosen Option : 3

Q.30 For mitigating the arcs in the contacts:

Ans 1. capacitance is placed in parallel

2. resistance is placed in parallel

3. capacitance is placed in series

4. resistance is placed in series

Question ID : 9744434575
Status : Answered
Chosen Option : 1

Q.31 Armouring of the cables is to:

Ans 1. increase the current carrying capacity of the cable

2. provide physical protection

3. provide greater insulation

4. reduce the capacitance of the cable

Question ID : 9744434541
Status : Answered
Chosen Option : 2

Q.32 Which of the following conducting materials are ordered in terms of increasing electrical
resistivity?
Ans 1. GI, Aluminium, Copper, Silver

2. Silver, Copper, Aluminium, GI

3. Copper, Aluminium, GI, Silver

4. Silver, Aluminium, GI, Copper

Question ID : 9744434521
Status : Answered
Chosen Option : 2
Q.33 Colour of light depends on:
Ans 1. speed of light

2. voltage applied

3. rating of the device

4. frequency of the voltage

Question ID : 9744434582
Status : Answered
Chosen Option : 1

Q.34 The average value of a full wave rectified DC output if the AC input is 16 V is:
Ans 1. 14.4 V

2. 8 V

3. 12.6 V

4. 12 V

Question ID : 9744434587
Status : Answered
Chosen Option : 3

Q.35 The current through a capacitor is:

Ans 1. proportional to the supply frequency

2. inversely proportional to the square of the supply frequency

3. proportional to the square of the supply frequency

4. inversely proportional to the supply frequency

Question ID : 9744434545
Status : Answered
Chosen Option : 1

Q.36 The internal resistance of a voltage source:

Ans 1. maintains the current supplied at increased load currents

2. maintains the available terminal voltage constant at increased load currents

3. causes reduction in the available terminal voltage at increased load currents

4. causes increase in the available terminal voltage at increased load currents

Question ID : 9744434526
Status : Answered
Chosen Option : 3

Q.37 Resonance in an RLC circuit is the state at which:

Ans 1. the impedance is purely inductive

2. the impedance is purely resistive

3. the impedance is purely capacitive

4. the impedance is zero

Question ID : 9744434549
Status : Answered
Chosen Option : 2
Q.38 Precision of an instrument ensures:
Ans 1. measured values closer to true value

2. measured values with great resolution

3. minimum deviations among the measured values irrespective of error

4. measured values lesser than true value

Question ID : 9744434568
Status : Answered
Chosen Option : 1

Q.39 Secondary cells differ from the primary cell because of which of the following?
Ans 1. The have less Ampere-hour rating

2. The can be recharged after discharge

3. They cannot be recharged after discharge

4. They have more Ampere-hour rating

Question ID : 9744434560
Status : Answered
Chosen Option : 2

Q.40 The tab on a soft drink can is an example of:

Ans 1. a pulley

2. a lever

3. an inclined plane

4. a wheel and axle

Question ID : 9744434532
Status : Answered
Chosen Option : 2

Q.41 Thevenin's theorem will be of great use when:

Ans 1. more than one source is there in the circuit

2. a small portion of the circuit is varying

3. two different circuits are interconnected

4. a small portion of the circuit is unchanged

Question ID : 9744434552
Status : Answered
Chosen Option : 1

Q.42 Which of the following does NOT affect coefficient of utilisation of a fluorescent lamp?
Ans 1. Lamp output

2. Colour of the wall

3. Low voltage

4. Reflectors used

Question ID : 9744434584
Status : Answered
Chosen Option : 3
Q.43 Which hand tools would you use for removing cable insulation?
Ans 1. A wood chisel and saw

2. A screwdriver

3. A pair of side cutters or knife

4. A tenon saw

Question ID : 9744434556
Status : Answered
Chosen Option : 3

Q.44 Which of the following is a distinct component in DC machines?

Ans 1. Armature

2. Commutator

3. Brushes

4. Excitation circuit

Question ID : 9744434588
Status : Answered
Chosen Option : 4

Q.45 Which of the following is true with regard to an AC circuit?

Ans 1. Apparent power is always equal to or greater than real power

2. Apparent power is zero when the circuit has resistances

3. Apparent power is always equal to or less than the real power

4. Apparent power is infinite when the circuit has resistances

Question ID : 9744434550
Status : Answered
Chosen Option : 1

Q.46 Oil based fire is:

Ans 1. Class D fire

2. Class C fire

3. Class B fire

4. Class A fire

Question ID : 9744434517
Status : Answered
Chosen Option : 3
Q.47 Earthing is nothing but:
Ans 1. connecting all supply points to earth through low resistance

2. bonding all metal parts associated with electrical systems and connecting to earth
through low resistance
3. bonding all metal parts associated with electrical systems and connecting to earth
through high resistance
4. connecting all supply points to earth through high resistance

Question ID : 9744434566
Status : Answered
Chosen Option : 2

Q.48 Armature reaction in a DC generator is:

Ans 1. armature current reducing the speed of the prime mover

2. armature current demagnetising the main field

3. armature current opposing the load current

4. armature current affecting the back EMF

Question ID : 9744434594
Status : Answered
Chosen Option : 2

Q.49 The large spacing between the conductors of overhead lines:

Ans 1. increases the resistance of the line

2. reduces the corona loss

3. reduces the line inductance

4. increases the capacitance of the line

Question ID : 9744434528
Status : Answered
Chosen Option : 2

Q.50 In recent years, the peak demand for electrical energy in India is about:
Ans 1. 5,00,000 MW

2. 8,00,000 MW

3. 1,00,000 MW

4. 2,00,000 MW

Question ID : 9744434527
Status : Answered
Chosen Option : 2
Q.51 The undesirable impact due to stroboscopic effect can be mitigated by:
Ans 1. wiring a capacitor in series with every alternate bulb in the group

2. wiring a capacitor in parallel with every alternate bulb in the group

3. wiring a capacitor in series with every bulb in the group

4. wiring a capacitor in parallel with every bulb in the group

Question ID : 9744434581
Status : Answered
Chosen Option : 4

Q.52 Bending the metal of a terminal barrel and pressing it onto a bare strip of wire in a way that
will not pull out or come loose over time is:
Ans 1. sleeving

2. grading

3. armouring

4. crimping

Question ID : 9744434540
Status : Answered
Chosen Option : 3

Q.53 Heat is a type of :

Ans 1. temperature

2. matter

3. energy

4. force

Question ID : 9744434535
Status : Answered
Chosen Option : 3

Q.54 Which of the following is true with regard to circuit analysis?

Ans 1. Mesh analysis may result in more equations than loop analysis

2. Mesh analysis and Loop Analysis are exactly the same.

3. Mesh analysis is more preferable than Loop analysis.

4. Loop Analysis is more preferable than Mesh analysis.

Question ID : 9744434551
Status : Answered
Chosen Option : 1

Q.55 Mechanical advantage is found by dividing load by:

Ans 1. effort

2. distance

3. mass

4. gravity

Question ID : 9744434534
Status : Answered
Chosen Option : 2
Q.56 Terminal joints connect:
Ans 1. a thick wire and a thin wire

2. copper conductors

3. a cable to a switchgear

4. solid conductors

Question ID : 9744434538
Status : Answered
Chosen Option : 2

Q.57 1-phase induction motor is made to start on its own by:

Ans 1. introducing a shunt field

2. introducing a capacitor to make a 2-phase magnetic field

3. introducing a voltage regulator

4. introducing brushes and commutators

Question ID : 9744434595
Status : Answered
Chosen Option : 2

Q.58 Efficacy of bulb is:

Ans 1. Lux/Ampere

2. Lumens/Watt

3. Lumens/m2 area
4. Lumens/Ampere

Question ID : 9744434585
Status : Answered
Chosen Option : 2

Q.59 Class B circuit breakers are fit to use for:

Ans 1. air conditioners

2. heaters

3. ballasts

4. motors

Question ID : 9744434576
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.60 Who discovered that a current carrying conductor produces a magnetic effect around it?
Ans 1. Benjamin Franklin

2. HC Oersted

3. Joseph Henry

4. Michael Faraday

Question ID : 9744434548
Status : Answered
Chosen Option : 2
Q.61 If there is an electrical fault, normally the residual current device switches off the supply in:
Ans 1. 100-200 milliseconds

2. 500-600 milliseconds

3. 10-50 milliseconds

4. 1-2 seconds

Question ID : 9744434571
Status : Answered
Chosen Option : 2

Q.62 Voltage across the series combination of two voltage sources of voltages 10 Volts and 15
Volts could be:
Ans 1. 10 V or 15 V

2. 10 V or 150 V

3. 15 V or 150 V

4. 5 V or 25 V

Question ID : 9744434546
Status : Answered
Chosen Option : 4

Q.63 The impedance of the voltmeter should be:

Ans 1. equal to circuit impedance

2. as high as possible

3. less than the circuit impedance

4. as low as possible

Question ID : 9744434553
Status : Answered
Chosen Option : 2

Q.64 The frictional force:

Ans 1. always acts in the direction of motion

2. always acts against the direction of motion

3. is always perpendicular to the direction of motion

4. varies with the size of the moving body

Question ID : 9744434530
Status : Answered
Chosen Option : 2

Q.65 A nickel-cadmium cell has:

Ans 1. cadmium as its negative plate

2. cadmium as its positive plate

3. cadmium with a small amount of iron as its negative plate

4. cadmium with a small amount of iron as its positive plate

Question ID : 9744434561
Status : Answered
Chosen Option : 2
Q.66 If a cell with an EMF of 2 V and an internal resistance of 0.4 Ω is connected across a 1.6 Ω
load resistor, then calculate the current that will flow.
Ans 1. 5 A

2. 1 A

3. 2 A

4. 4 A

Question ID : 9744434565
Status : Answered
Chosen Option : 2

Q.67 The equivalent resistance of a parallel combination of two 50 Ohms resistors is:
Ans 1. 100 Ohms

2. 25 Ohms

3. 0 Ohms

4. 50 Ohms

Question ID : 9744434543
Status : Answered
Chosen Option : 2

Q.68 The great advantage of overhead transmission lines over underground cables is:
Ans 1. low frequency of faults

2. low maintenance cost over a long period

3. less effect of line capacitance

4. low voltage drop due to line inductance

Question ID : 9744434523
Status : Answered
Chosen Option : 2

Q.69 Which method is a good choice for reviving breath in the victim of electric shock who is
injured in the belly?
Ans 1. Schafer's method

2. Mouth-to-mouth method

3. Mouth-to-nose method

4. Nelson's arm – Lift back pressure method

Question ID : 9744434516
Status : Answered
Chosen Option : 2
Q.70 When selecting a diode for rectification circuit, ensure that it can operate:
Ans 1. at the effective voltage of the input

2. at the average voltage of the input

3. at peak voltage of the input

4. at the RMS voltage of the input

Question ID : 9744434583
Status : Answered
Chosen Option : 3

Q.71 The unit for electromotive force is:

Ans 1. Ampere

2. Watt

3. Volt

4. Newton

Question ID : 9744434544
Status : Answered
Chosen Option : 3

Q.72 An ammeter capable of taking 2.5 A is to be used in conjunction with a CT to measure a bus-
bar current of up to 2000 A. The turns ratio is:
Ans 1. 1 : 800

2. 1 : 2.5

3. 1 : 2000

4. 1 : 80

Question ID : 9744434573
Status : Answered
Chosen Option : 1

Q.73 The voltage generated in a DC generator is:

Ans 1. is equal to the magnetic field intensity

2. independent of the magnetic field

3. proportional to the magnetic field

4. inversely proportional to the magnetic field

Question ID : 9744434590
Status : Answered
Chosen Option : 3

Q.74 Fusing current of a fuse is:

Ans 1. maximum current the fuse can carry without blowing

2. minimum current causing the fuse to blow

3. minimum current the fuse can carry without blowing

4. maximum current causing the fuse to blow

Question ID : 9744434554
Status : Answered
Chosen Option : 2
Q.75 For calculating lighting requirements, which of the following is used?
Ans 1. Lenz law

2. Inverse square law

3. Law of reflection

4. Snell’s law

Question ID : 9744434580
Status : Answered
Chosen Option : 2

Q.76 Switch gears that are flame proof are preferred for:
Ans 1. high tension transmission lines

2. substations

3. low tension transmission lines

4. mines

Question ID : 9744434577
Status : Answered
Chosen Option : 4

Q.77 A primary dry cell is called so because:

Ans 1. the electrolyte is dry

2. the electrolyte is a moist paste

3. the container is dry

4. electrodes are dry

Question ID : 9744434564
Status : Answered
Chosen Option : 2

Q.78 Resistance of the earth wire is to be in the order of:

Ans 1. 100s of Ohms

2. 1000s of Ohms

3. 10s of Ohms

4. 10000s of Ohms

Question ID : 9744434520
Status : Answered
Chosen Option : 3

Q.79 Cogeneration is nothing but:

Ans 1. generating both AC and DC in a single plant

2. generating power as a bye-product in an industry

3. generating power using two different types of turbines

4. generating powers from two different sources in a plant

Question ID : 9744434592
Status : Answered
Chosen Option : 1
Q.80 For making wire joints, the skinning of the insulation is to be done for a length of at least:
Ans 1. 8 mm

2. 10 mm

3. 5 mm

4. 2 mm

Question ID : 9744434519
Status : Answered
Chosen Option : 2

Section : Reasoning

Q.1

Ans 1.

2.

3.

4.

Question ID : 9744434601
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.2

Ans 1.

2.

3.

4.

Question ID : 9744434597
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.3

Ans 1.

2.

3.

4.

Question ID : 9744434602
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.4

Ans 1.

2.

3.

4.

Question ID : 9744434605
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.5

Ans 1.

2.

3.

4.

Question ID : 9744434598
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.6

Ans 1.

2.

3.

4.

Question ID : 9744434600
Status : Answered
Chosen Option : 1

Q.7

Ans 1.

2.

3.

4.

Question ID : 9744434604
Status : Answered
Chosen Option : 2

Q.8

Ans 1.

2.

3.

4.

Question ID : 9744434599
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.9

Ans 1.

2.

3.

4.

Question ID : 9744434603
Status : Answered
Chosen Option : 1
Q.10

Ans 1.

2.

3.

4.

Question ID : 9744434596
Status : Answered
Chosen Option : 4

Section : Quantitative Aptitude

Q.1

Ans 1.

2.

3.

4.

Question ID : 9744434612
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.2

Ans 1.

2.

3.

4.

Question ID : 9744434609
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.3

Ans 1.

2.

3.

4.

Question ID : 9744434613
Status : Answered
Chosen Option : 2

Q.4
Ans 1.

2.

3.

4.

Question ID : 9744434615
Status : Not Answered
Chosen Option : --

Q.5

Ans 1.

2.

3.

4.

Question ID : 9744434607
Status : Answered
Chosen Option : 3

Q.6

Ans 1.

2.

3.

4.

Question ID : 9744434614
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.7

Ans 1.

2.

3.

4.

Question ID : 9744434611
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.8

Ans 1.

2.

3.

4.

Question ID : 9744434606
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.9
Ans 1.

2.

3.

4.

Question ID : 9744434608
Status : Answered
Chosen Option : 3

Q.10

Ans 1.

2.

3.

4.

Question ID : 9744434610
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Section : General Awareness

Q.1 The western coast is divided into four divisions, of which the Kathiawar coast lies in ______.
Ans 1. Kerala

2. Maharashtra

3. Gujarat

4. Karnataka

Question ID : 9744434622
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.2 What is the name of the Virtual Space Museum launched by Indian Space Research
Organisation (ISRO) in August 2022, making a digital platform for people to interact with
missions related to ISRO?
Ans 1. SPACETECH

2. SPARK

3. SATELIGHT

4. FLAME

Question ID : 9744434616
Status : Answered
Chosen Option : 1

Q.3 In September 2022, Indian Space Research Organisation (ISRO) successfully tested IAD
technology which is expected to be a game-changer with numerous implications for future
missions including to Mars and Venus. What is the full form of IAD?
Ans 1. Inflatable Aerospace Decelerator

2. Inflatable Aerodynamic Developer

3. Inflatable Aerodynamic Decoder

4. Inflatable Aerodynamic Decelerator

Question ID : 9744434617
Status : Answered
Chosen Option : 2

Q.4 Who among the following pressurised the British authorities to pass the Hindu Widows
Remarriage Act in 1856?
Ans 1. Annie Besant

2. Bipin Chandra Pal

3. Keshab Chandra Sen

4. Ishwar Chandra Vidyasagar

Question ID : 9744434618
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.5 Melanoma, the deadliest kind of skin cancer, may be caused by exposure to ______.
Ans 1. sulphur dioxide pollution

2. chlorofluorocarbons

3. carbon monoxide pollution

4. ultraviolet radiation

Question ID : 9744434623
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.6 In which year did the Reserve Bank of India launch the ‘RBI Retail Direct Scheme’ for retail
investors to increase retail participation in Government Securities?
Ans 1. 2013

2. 2021

3. 2019

4. 2016

Question ID : 9744434621
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Q.7 Where is the Buddhist monument Vishwa Shanti Stupa located in India?
Ans 1. Bihar

2. Sikkim

3. Assam

4. Uttar Pradesh

Question ID : 9744434619
Status : Answered
Chosen Option : 1

Q.8 Which of the following features of the Indian Constitution is borrowed from the Constitution
of France?
Ans 1. Republic

2. Impeachment of the President

3. Vesting of residuary powers in the Centre

4. Single Citizenship

Question ID : 9744434624
Status : Answered
Chosen Option : 1
Q.9 Which city of the Indus Valley civilisation is located at the head of the Gulf of Cambay?
Ans 1. Kalibangan

2. Chanhudaro

3. Lothal

4. Surkotada

Question ID : 9744434620
Status : Answered
Chosen Option : 1

Q.10 Who among the following clinched a bronze medal in the Javelin throw category at the World
Para Athletics Grand Prix held in Morocco in September 2022?
Ans 1. Anil Kumar

2. Neeraj Yadav

3. Ranjeet Bhati

4. Ajeet Singh

Question ID : 9744434625
Not Attempted and
Status :
Marked For Review
Chosen Option : --

Section : English Language

Q.1 Select the most appropriate synonym of the given word.

Pompous
Ans 1. Unpretending

2. Simple

3. Showy

4. Naive

Question ID : 9744434627
Status : Not Answered
Chosen Option : --

Q.2 Select the INCORRECTLY spelt word.

Ans 1. Partinent

2. Procrastinate

3. Protrude

4. Prophetic

Question ID : 9744434629
Not Attempted and
Status :
Marked For Review
Chosen Option : --
Q.3 Select the most appropriate meaning of the given idiom.

To clip one’s wings

Ans 1. To learn a new skill

2. To break free

3. To create an opportunity

4. To deprive one of power

Question ID : 9744434631
Status : Answered
Chosen Option : 1

Q.4 Select the most appropriate option to fill in the blanks.

My mother tells ______ beautiful story of ______ tiny hummingbird determined to save its
home from ______ destructive forest fire.
Ans 1. the, an, a

2. a, a, a

3. the, an, an

4. a, a, an

Question ID : 9744434626
Status : Answered
Chosen Option : 2

Q.5 Select the most appropriate meaning of the given idiom.

Pull a fast one

Ans 1. To help someone

2. To abuse someone

3. To play a trick

4. A quick response

Question ID : 9744434632
Status : Answered
Chosen Option : 2

Q.6 Select the INCORRECTLY spelt word.

Ans 1. Acustics

2. Nepotism

3. Inherent

4. Flabbergasted

Question ID : 9744434630
Status : Answered
Chosen Option : 1
Q.7 Select the most appropriate ANTONYM of the given word.

Diligence
Ans 1. Perseverance

2. Carelessness

3. Attention

4. Vigour

Question ID : 9744434628
Status : Answered
Chosen Option : 3

Comprehension:
Read the given passage and answer the questions that follow.

Stress is an easily identifiable condition that not only causes anxiety but is also highly
psychosomatic, affecting everything from our digestive system to our skin. This is why
prevention is so important in avoiding the toll that stress takes on us—and why many experts
recommend practicing mindfulness. The central premise of this stress-reduction method is
focusing on the self: noticing our responses, even if they are conditioned by habit, in order to
be fully conscious of them. In this way, we connect with the here and now and limit thoughts
that tend to spiral out of control. “We have to learn to turn off the autopilot that’s steering us in
an endless loop. We all know people who snack while talking on the phone or watching the
news. You ask them if the omelette they just ate had onion in it, and they can’t tell you,” says
Roberto Alcibar, who abandoned his fast-paced life to become a certified instructor of
mindfulness after an illness threw him into a period of acute stress.
One way to reach a state of mindfulness is through meditation, which helps filter the
information that reaches us from the outside world. It can also be achieved through breathing
exercises, yoga and body scans. Achieving mindfulness involves a gradual process of training,
but with a bit of practice we can learn to focus our mind completely, which reduces stress and
helps us live longer.

SubQuestion No : 8
Q.8 Which of the following stress reduction techniques is NOT mentioned in the passage?
Ans 1. Meditation

2. Breathing exercises

3. Talking to friends

4. Yoga

Question ID : 9744434636
Status : Not Answered
Chosen Option : --
 Comprehension:
Read the given passage and answer the questions that follow.

Stress is an easily identifiable condition that not only causes anxiety but is also highly
psychosomatic, affecting everything from our digestive system to our skin. This is why
prevention is so important in avoiding the toll that stress takes on us—and why many experts
recommend practicing mindfulness. The central premise of this stress-reduction method is
focusing on the self: noticing our responses, even if they are conditioned by habit, in order to
be fully conscious of them. In this way, we connect with the here and now and limit thoughts
that tend to spiral out of control. “We have to learn to turn off the autopilot that’s steering us in
an endless loop. We all know people who snack while talking on the phone or watching the
news. You ask them if the omelette they just ate had onion in it, and they can’t tell you,” says
Roberto Alcibar, who abandoned his fast-paced life to become a certified instructor of
mindfulness after an illness threw him into a period of acute stress.
One way to reach a state of mindfulness is through meditation, which helps filter the
information that reaches us from the outside world. It can also be achieved through breathing
exercises, yoga and body scans. Achieving mindfulness involves a gradual process of training,
but with a bit of practice we can learn to focus our mind completely, which reduces stress and
helps us live longer.

SubQuestion No : 9
Q.9 Select the most appropriate synonym of ‘toll’ as used in the passage.
Ans 1. Damage

2. Duty

3. Payment

4. Tax

Question ID : 9744434634
Status : Not Answered
Chosen Option : --

Comprehension:
Read the given passage and answer the questions that follow.

Stress is an easily identifiable condition that not only causes anxiety but is also highly
psychosomatic, affecting everything from our digestive system to our skin. This is why
prevention is so important in avoiding the toll that stress takes on us—and why many experts
recommend practicing mindfulness. The central premise of this stress-reduction method is
focusing on the self: noticing our responses, even if they are conditioned by habit, in order to
be fully conscious of them. In this way, we connect with the here and now and limit thoughts
that tend to spiral out of control. “We have to learn to turn off the autopilot that’s steering us in
an endless loop. We all know people who snack while talking on the phone or watching the
news. You ask them if the omelette they just ate had onion in it, and they can’t tell you,” says
Roberto Alcibar, who abandoned his fast-paced life to become a certified instructor of
mindfulness after an illness threw him into a period of acute stress.
One way to reach a state of mindfulness is through meditation, which helps filter the
information that reaches us from the outside world. It can also be achieved through breathing
exercises, yoga and body scans. Achieving mindfulness involves a gradual process of training,
but with a bit of practice we can learn to focus our mind completely, which reduces stress and
helps us live longer.

SubQuestion No : 10
Q.10 What does mindfulness mean?
Ans 1. Spiral out of control

2. Period of acute stress

3. Being here and now

4. Conditioned by habit

Question ID : 9744434635
Status : Not Answered
Chosen Option : --