Request For Approval

JCVA-JADE-ASYA-RFA-AR-002
RFA NO. : MRFA-AR-7324-007-2024-R1
CP NO. : CP-03 CIVIL, STRUCTURAL AND MASONRY (CSM) WORKS
SMDC JADE RESIDENCES * Refer to approved Submittal Schedule dated _____________

Transmittal to : JCVA & ASSOCIATES From : EEI CORPORATION Date: January 12, 2024
I Project Managers Contractor Drwg No. N/A

Reference No. : MRFA-AR-7324-007-2024

[ ] New submittal Date : 05 January, 2024
[ X ] Resubmittal ( X )1 ( )2 ( ) 3

Sample Qty.: Title / Description / Manufacturer :

12 Sheets incl. top sheet Bentonite Waterstop (WATERSTOP-RX 101 Expanding Waterstop for Concrete Joint
Construction Joint)
Intended for: Construction Joints

Attachments: Product Manual, Material Safety Data Sheet, Sample & Previous Approval
(From Other Project - SMDC Glam Residences)

Specs. Section, Title & Paragraph / Drawing, Detail Reference:

5.0 Bill of Quantities Dated 21 Sept 23 - Civil Works, Item "M" (No Client Specification)

By: Date Received Date Required +/-

01/15/24 from Contractor from Contractor: *
01/15/24
MMR ALVAREZ / EJ FRESNOSA JM Beltran
SR. ENG'G MANAGER / PROJECT MANAGER Received by: JCVA & ASSOCIATES
EEI CORPORATION Project Managers
Other Remarks on above Submission: MG Martps
Jan 16, 2024 / 9:00am
Transmittal to : Asya Date Received Received by:
Consultant by Consultant
II
From: JCVA & ASSOCIATES Consultant
Project Managers
Other Remarks on above Submission:

Transmittal to : From :
JCVA & ASSOCIATES Consultant
III Project Managers
Action: (Pls. encircle one)
A Approved B Approved as Noted C Revise & Resubmit as Noted D Disapproved / New Submittal Required
Notes:
-OK with the brand
-Provide physical sample with the CETCO logo for validation
-Contractor to guarantee all the works
Date Returned Date Required from +/-
by Consultant Consultant: *
w.sarang
30-Jan-2024
Name & Signature Name & Signature Name & Signature Received by: JCVA & ASSOCIATES
Project Managers
Other Remarks on above Submission:

Transmittal to : EEI CORPORATION Date Returned Date Required +/-

Contractor to Contractor by Contractor: *
IV
From: JCVA & ASSOCIATES Received by: EEI CORPORATION
Project Managers Contractor

Copies : Owner Architect Quantity Surveyor Others _________________

product manual

waterstop-rx®
expanding concrete joint waterstop

www.cetco.com
product manual

waterstop-rx®
expanding concrete joint waterstop
utes the expansive force over a greater area. Waterstop-RX 102 is

CONTENTS extruded in half-circle (crescent) shape measuring 19 mm x 9 mm x 10

m (3/4” x 3/8” x 33’ 4”). See Table 1.

Section 1: Product Description CETSEAL is a multi-purpose, single component polyether moisture cure
adhesive used to secure Waterstop-RX into position. Apply a continu-
Section 2: General Applications ous bead of CETSEAL to substrate then install Waterstop-RX before
CETSEAL skins over and cures. Adhesive yeild will vary with use, sub-
Section 3: General Installation Procedures strate and application.

Section 4: Penetrations

Section 5: Pile Caps and Grade Beams

Section 6: Property Line Installations Before

Hydration
Section 7: Irregular Concrete Surfaces

Section 8: Joining Waterstop-RX to PVC Waterstops

SECTION 1 After
Hydration
PRODUCT DESCRIPTION
Waterstop-RX is a flexible strip concrete construction joint waterstop
that provides a permanent seal by expanding upon contact with water.
Figure 1.1 - Swelling property of Waterstop-RX
Waterstop-RX is an active sodium bentonite based waterstop that is
designed to replace conventional passive PVC dumbbell waterstops,
thus eliminating the requirement of split-forming and product seam
welding.

Waterstop-RX is manufactured in light weight, flexible coils that can

be installed in both hot and cold weather. The product is adhered to
concrete, steel, and PVC (pipes) with CETSEAL; at or exceeding the re-
quired minimum distance from the exterior concrete
surface.
RX-101
The key to Waterstop-RX is sodium bentonite. Sodium bentonite Poly scrim
swells when in contact with water, forming an impermeable barrier. This reinforcement
swelling property allows Waterstop-RX to form a permanent pressure
seal within the concrete joint, thus eliminating water migration over or
along the waterstop (see Figure 1.1). In addition to forming a positive
pressure seal, the product’s expansion properties allow it to seal small
cracks and void areas. Waterstop-RX has been successfully tested by RX-102
independent testing firms to over 60 meters (200 feet) of hydrostatic RX-101T
water pressure, under both continuous emersion and wet/dry cycling.

Waterstop-RX is extruded in three sizes and shapes (see Figure 1.2). Figure 1.2 - Three sizes and shapes of Waterstop-RX
Waterstop-RX 101 is extruded in a rectangular shape measuring 25
mm x 19 mm x 5.03 m (1”x3/4”x16’8”). Waterstop-RX 101T is ex-
truded in a trapezoidal shape measuring 31 mm x 12 mm x 6 m (1-1/4”
x 1/2” x 20’) with a reinforcing plastic scrim embedded in the top sur-
face for high tensile strength. The patented trapezoidal shape distrib-

2870 Forbs Avenue Hoffman Estates, IL 60192 | 847.851.1800 | 800.527.9948

-2-
 SECTION 2 SECTION 3
GENERAL APPLICATIONS GENERAL INSTALLATION
Waterstop-RX applications include both vertical and horizontal con- Surface Preparation
crete construction joints, new-to-existing construction, irregular sur- Surfaces should be clean and dry. Remove all dirt, rocks, rust or other
faces, and around throughwall penetrations, such as plumbing and debris. Do not install Waterstop-RX in standing water.
electrical conduit. Waterstop-RX is designed for both hydrostatic and
non-hydrostatic conditions. Waterstop-RX is not designed, nor intend- adhesive
ed to function as an expansion joint sealant. Contact manufacturer for Apply a continuous bead of CETSEAL along the substrate where
precast concrete applications, technical information and approval. Waterstop-RX will be installed. Assure proper 75 mm (3”) concrete
coverage wll be maintained. Keep the nozzle tip pressed against the
Waterstop-RX is designed for structural concrete with a minimum of o
concrete at a 45 angle during application.
3000 psi. 101 and 101T, require a minimum 75 mm (3”) of concrete
coverage. Waterstop-RX 102 requires a minimum concrete coverage
of 50 mm (2”). Installation
After applying a continuous bead of CETSEAL, remove release paper,
RX 101 and RX 101T are designed for vertical and horizontal reinforced then firmly press the entire length of Watestop-RX onto the adhesive.
concrete 200mm (8”) thick or greater, with two rows of reinforcing steel For vertical and overhead applications, firmly press a minimum of 15
(see Figure 2.1). RX 101T (trapezoidal) is recommended for shotcrete or seconds to assure adhesion. Apply Waterstop-RX within 30 minutes
gunite concrete construction, extreme hot weather and difficult applica- of adhesive installation; waterstop must be placed into adhesive pri-
tions. RX 102 is designed for vertical reinforced concrete 125 mm (5”) or to CETSEAL skinning over and curing. CETSEAL may be applied to
thick or greater; and horizontal reinforced concrete 100 mm (4”) thick damp surfaces, but not in standing water.
or greater. RX 102 is designed primarily for concrete with one row of Waterstop-RX is not a self-adhering product. Use CETSEAL to adhere
reinforcement, concrete curbs, planter walls, and light weight concrete. the product. Mechanical fasteners should not be used to secure prod-
uct alone, but may be used in conjunction with CETSEAL.
Footing Joint Tightly butt coil ends together to form a continuous waterstop (do not
Vertical Wall Joint overlap coil ends). Place in maximum practical lengths to minimize coil
Waterstop-RX end joints. Where required, cut coils with knife or utility blade to fit coil
ends together. Pour Concrete.
Concrete
limitations
Waterstop-RX is not designed, nor intended to function as
an expansion joint sealant. RX-101 and RX 101T require a 75 mm
(3”) minimum concrete coverage to the exterior concrete surface (see
Figure 3.1). RX 102 requires a 50 mm (2”) minimum concrete coverage
Min 75 mm (3”) to to the exterior concrete surface (see Figure 3.2).
exterior wall surface Concrete work shall use conventional cast-in-place forms that produce
a smooth surface. Do not use stay-in-place concrete forming; use re-
movable forming products only.
Place Waterstop-RX
inside of outer most For concrete or other construction techniques not covered herein,
dowels contact CETCO regarding product use and installation guidelines.

Figure 2.1 - Typical placement of Waterstop-RX at concrete

construction joint

Product table
product size shape ln ft/carton min concrete coverage
RX-101 1" X 3/4" X 16'8" Rectangule 100 75 mm (3”)
RX-101T 1 1/4" x 1/2" x 20' Trapezoid with poly reinforcement 120 75 mm (3”)
RX-102 3/4" x 3/8" x 33' 4" Half circle 200 50 mm (2”)

www.CETCO.com
product manual

waterstop-rx®
expanding concrete joint waterstop
Waterstop-RX should not be prehydrated by submersion or remain in
contact with water prior to concrete pour. If the product exhibits consid-
erable swell prior to confinement in the joint, it must be replaced with
SECTION 4
new material. PENETRATIONS
In conditions where severe ground water chemical contamination ex-
ists, or is expected, consult with manufacturer for compatibility infor- Following the General Installation Procedures in Section 3, install
mation and approval. Waterstop-RX® directly around all applicable single and multiple
poured-in-place or sleeved pipe penetrations (see Figure 4.1).
Waterstop-RX is recommended for installation outside of any formed
keyway in poured-in-place concrete construction. Waterstop-RX can Single Pipe Penetration: Install Waterstop-RX around outer diam-
be installed in a formed keyway with the approval of the structural en- eter of the pipe (see Figure 4.2). Waterstop-RX 102 shall be installed
gineer. Consult manufacturer for recommendations on conditions not around all polyvinyl chloride (PVC) pipes.
represented herein.
Multiple Pipe Penetrations: Install Waterstop-RX around
Place Waterstop-RX each pipe, as well as, around any block out box construction joint.
Waterstop-RX in inside of outer most Waterstop-RX 102 shall be installed around penetrations with less
all cold pour joints reinforcement row than 4” (100mm) between penetrations (see Figure 4.3).
Min 75 mm (3”) Sleeved Pipe Penetrations: Install Waterstop-RX around the outer
diameter of the sleeve. Install another Waterstop-RX strip between
the sleeve’s inner diameter and the pipe, contacting both surfaces con-
tinuously (see Figure 4.4). When there is an excessive gap between the
inner diameter of the sleeve and the pipe, it may be necessary to install
two separate Waterstop- RX strips - one on the inner diameter and the
other on the pipe. Then completely fill the void area between the sleeve
Waterstop-RX and the pipe with non-shrink grout (see Figure 4.5).
Structural Slab Min 75 mm (3”) Rebar Consult manufacturer for recommedations on conditions not repre-
sented herein.

Compacted Substrate Clean surface and

Figure 3.1 - Placement of Waterstop-RX 101 & 101T at typical apply CETSEAL
construction joints with required 75 mm (3”) concrete coverage.

Rebar
Waterstop-RX in
all cold pour joints Waterstop-RX
102
Waterstop-RX

Min 50 mm (2”)
Figure 4.1 - Waterstop-RX installed around all applicable penetrations.

Waterstop-RX
Structural Slab 102 Rebar
Min 50 mm (2”)

Compacted Substrate Waterstop-RX

Figure 3.2 - Placement of Waterstop-RX 102 at typical construction
joints with required 50 mm (2”) concrete coverage. Figure 4.2 - Single pipe penetration

2870 Forbs Avenue Hoffman Estates, IL 60192 | 847.851.1800 | 800.527.9948

-4-
 SECTION 5
PILE CAPS AND GRADE BEAMS
Following the General Installation Procedures in Section 3, install Wa-
terstop-RX in all applicable concrete construction joints around or
adjacent to pile caps and grade beams.

Non-shrink grout Waterstop-RX Install Waterstop-RX around pile caps and grade beams above the
layer (not contacting) of exterior waterproofing to establish a separate
Figure 4.3 - Multiple pipe penetration waterstop layer (see Figure 5.3). Contour all I-beams extending outward
from pile caps with Waterstop-RX (see Figure 5.1) or encircle all metal
Non-shrink grout reinforcement rods extending out of pile caps (see Figure 5.2).

Waterstop-RX
I-Beam

Metal sleve Waterstop-RX

Pile

Figure 4.4 - Sleeved Pipe Waterstop-RX

Waterstop-RX
I-Beam
Non-shrink grout

Pile
Waterstop-RX
Metal sleeve

Figure 4.5 - Sleeved pipe (excessive gap)

Figure 5.1 - Waterstop-RX Figure 5.2 - Waterstop-RX
encircling pile cap metal I-beam encircling pile caps mental
reinforcement
Waterstop-RX
Waterstop-RX

Pile cap
CETCO
waterproofing
Grade beam Waterstop-RX

Piling

Figure 5.3 - Waterstop-RX at grade beams and pile caps

www.CETCO.com
product manual

waterstop-rx®
expanding concrete joint waterstop
Install Waterstop-RX within all applicable concrete construction joints
SECTION 6 when the wood lagging is positioned adjacent to the soldier piles inside
flange (see Figure 6.2).
PROPERT Y LINE INSTALLATIONS
Install Waterstop-RX in all applicable concrete construction joints
for metal sheet piling or concrete cassion construction. Install Water-
Following the General Installation Procedures in Section 3, install stop-RX around all soldier pile tie-back boxes through wall construc-
Waterstop-RX® in all applicable horizontal and vertical construction tion joints (see Figure 6.3).
joints within the structural property line wall, including concrete inter-
facejoints with soldier piles. Use Waterstop-RX 101T (trapezoidal) for shotcrete or gunite concrete
Install Waterstop-RX directly to soldier piles when wood lagging is po- construction. With shotcrete wall construction, a single strip of Water-
sitioned outside the piles toward the retained earth or when the wood stop-RX shall be installed in all shotcrete lift joints. For hydrostatic
agging is positioned adjacent to the pile’s outer flange (see Figure 6.1). conditions, two strips of Waterstop-RX shall be installed in all shot-
crete cold construction joints.

Soldier pile CETCO

Earth Wood lagging waterproofing

Waterstop-
RX min 3" (75
mm) coverage

Waterstop-RX CETCO
waterproofing Tie-
back Pre-molded
rod TB cover filled
Soldier pile with foam

Figure 6.1 - Waterstop-RX installed when wood lagging is positioned outside the soldier piles or Waterstop-
adjecent to piles outer flange RX min 3" (75
mm) coverage
Soldier pile Wood lagging

Wood Cast-in-place
lagging concrete wall

Waterstop-RX

CETCO
Concrete wall waterproofing
Figure 6.3 - Typical tie-back section detail
prior to grouting
Figure 6.2 - Waterstop-RX installed when wood lagging is positioned adjacent to soldier piles
inside flange

2870 Forbs Avenue Hoffman Estates, IL 60192 | 847.851.1800 | 800.527.9948

-6-
 SECTION 7 Irregular concrete

IRREGULAR CONCRETE Waterstop-RX

& STONE SURFACES

Following the General Installation Procedures in Section 3, install
Waterstop-RX® to existing irregular concrete or stone surfaces.
Press Waterstop-RX continuously against irregular surface, contour-
ing all rises and depressions (see Figure 7.1). Do not span cavities or Contour concrete
cracks leaving a gap between the surface and the Waterstop-RX. In
special conditions it may be necessary to install Waterstop-RX in an Figure 7.1 - Waterstop-RX installed on irregular concrete
irregular path to circumvent deep depressions or cracks.

SECTION 8
JOINING Waterstop-RX TO 75 mm (3”) min
PVC waterstop
PVC WATERSTOPS

Following the General Installation Procedures in Section 3, install Earth Waterstop-RX

Waterstop-RX on the exterior side of the PVC dumbbell waterstop
(see Figure 8.1). Waterstop-RX should be in direct contact and over-
lap the passive PVC dumbbell waterstop by a minimum of 75 mm (3”).
Figure 8.1 - Overlapping dumbbell waterstop
Consult manufacturer for recommendations on conditions not repre-
sented herein.

LIMITED WARRANTY
The information and data contained herein is believed to be accurate and shipped) of goods not complying with this agreement or at seller’s election, to
reliable. Specifications and other information contained herein supersede all the repayment of, or crediting buyer with, an amount equal to the purchase
previously printed material and are subject to change without notice. price of such goods, whether such claims are for breach of warranty or neg-
Manufacturer’s warranty of installed system is available. Contact seller for ligence.
terms and sample documents including all limitations. Any claim by buyer with reference to the goods sold hereunder for any cause
All goods sold by seller are warranted to be free from defects in material and shall be deemed waived by buyer unless submitted to seller in writing within
workmanship. thirty (30) days from the date buyer discovered or should of discovered, any
The foregoing warranty is in lieu of and excludes all other warranties not claimed breach.
expressly set forth herein, whether expressed or implied by operation of law Materials should be inspected and tested by purchaser prior to their use if
or otherwise including but not limited to any implied warranties of merchant- product quality is subject to verification after shipment. Performance guaran-
ability or fitness. tees are normally supplied by the applicator.
Seller shall not be liable for incidental or consequential losses, damages or
expenses, directly or indirectly arising from the sale, handling or use of the Note: Waterstop-RX is not an expansion joint material. Expansion joints
goods, or from any other cause relating thereto, and seller’s liability hereun- shall be the responsibility of Others.
der in any case is expressly limited to the replacement (in the form originally

www.CETCO.com
 CETCO, a wholly owned subsidiary of AMCOL International Corporation

1.800.527.9948 | www.cetco.com

ABOUT AMCOL International Corporation

Founded in 1927, AMCOL International Corporation is a leading pro-
ducer and marketer of diverse specialty materials with a core expertise
in minerals and polymer science. Through four business segments—
Performance Materials, Construction Technologies, Energy Services, and
Transportation—AMCOL creates solutions that enhance the quality,
efficiency and sustainability of our customers’ products and services in
a growing global marketplace.

Amcol holds more than 375 worldwide patents, and our focus on research
and development empowers us to be industry leaders. Technical expertise,
coupled with unparalleled customer relationships and supported by more
than 2,400 employees in more than 26 countries, makes us trusted part-
ners in major end markets.

w w w. A MC OL .c om

Updated: NOVEMBER 2013

© 2013 CETCO. IMPORTANT: The information contained herein supersedes all previous printed versions, and
is believed to be accurate and reliable. For the most up-to-date information, please visit www.CETCO.com.
CETCO accepts no responsibility for the results obtained throught application of this product. CETCO reserves
the right to update information without notice. www.CETCO.com
2870 Forbs Avenue Hoffman Estates, IL 60192
PM_WATERSTOPRX_AM_EN_201311_v1 847.851.1800 | 800.527.9948
TECHNICAL DATA

wATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP

DESCRIPTION penetrations, such as plumbing and utility Tightly butt coil ends together to form a
Waterstop-RX is a hydrophilic strip pipes. Additionally Waterstop-RX can seal continuous waterstop - do not overlap coil
waterstop designed to stop water infiltration around concrete pilings and steel H-piles ends. Place in maximum practical lengths to
through cast-in-place concrete construction passing through the slab. Waterstop-RX minimize coil end joints. Where required, cut
joints by expanding upon contact with water works in both continuous hydrostatic and coils with a sharp knife or utility blade to fit
to form a positive seal against the concrete. intermittent hydrostatic conditions. coil ends together. Make horizontal to vertical
The key to Waterstop-RX’s effectiveness is transitions by abutting product coil sections
its superior expansion to seal and fill voids Waterstop-RX products are designed together, no special accessory pieces are
and cracks in the concrete. Waterstop-RX for reinforced structural concrete with required.
is an active bentonite/butyl-rubber based a minimum of 20N/mm2 (3,000 psi)
waterstop that is designed to replace passive compressive strength. RX-101 and RX-101T At structural and pipe penetrations, cut into
PVC/Rubber dumbbell waterstops, thereby are designed for concrete 200 mm (8”) thick strips to fit around the penetration. Apply to
eliminating the requirement of special or greater with two rows of reinforcing steel. adhesive and abut coil ends together.
pieces, split-forming and seam welding. RX-102 is designed for vertical concrete
Waterstop-RX has been successfully 150 mm (6”) thick or greater; and horizontal On irregular surfaces such as stone or rough
tested by independent testing firms to over concrete no less than 100 mm (4”) thick. concrete, make sure Waterstop-RX remains
60 meters (200 feet) of hydrostatic water RX-102 should be used in concrete with one in direct contact with the substrate along the
pressure, under both continuous immersion row of steel reinforcement, concrete curbs, entire installation. There should not be any
and wet/dry cycling. planter walls, fountains, and lightweight air gap between the Waterstop-RX and the
structural concrete. substrate.
Waterstop-RX is available in three Waterstop-RX is a reliable, cost-effective
sizes and shapes (see Product Table). means to stop water infiltration through
Waterstop-RX 101 is produced in a concrete cold joints. It can also be used
rectangular shape measuring 25 x 19 mm around pipe and structural penetrations
(1” x 3/4”). Waterstop-RX 101T is produced Footing/Wall Joint
in a trapezoidal shape measuring 31 x 12 mm
(1-1/4” x 1/2”) with a reinforcing plastic scrim
INSTALLATION
Surface preparation: Surfaces should be Waterstop-RX
embedded in the top surface for high tensile
clean and dry. Remove all dirt, rocks, rust
strength. The patented trapezoidal shape
or other construction debris. Do not install
distributes the expansive force over a greater
Waterstop-RX in standing water or on an
area and allows the concrete to flow more
iced substrate.
readily over the product during placement.
Waterstop-RX 102 is produced in a half-
Adhesive: Apply a continuous bead of
circle (Crescent) shape measuring 19 x 9 mm
CETSEAL along the substrate where
(3/4” x 3/8”).
Waterstop-RX will be installed. Assure
proper 75 mm (3”) concrete coverage will
Though Waterstop-RX possesses good
be maintained. Keep the nozzle tip pressed
resistance to many chemicals, the waterstop
against the concrete at a 45o angle during
is not intended to be used as the primary joint
application.
sealant for chemical containment vessels.
Consult manufacturer for guidance regarding
Installation: After applying a continuous bead
chemical compatibility for secondary
of CETSEAL, remove release paper, then firmly Place Waterstop-RX
chemical containment applications.
press the entire length of Waterstop-RX inside of outer most
Additionally, Waterstop-RX is not an
onto the adhesive. For vertical and overhead reinforcing dowels
expansion joint sealant; contact CETCO for 75 mm
applications, firmly press a minimum of 15 (3”)
expansion joint applications.
seconds to assure adhesion. For best results Minimum 75 mm (3”)
apply Waterstop-RX within 15 minutes of to exterior surface of
APPLICATIONS adhesive installation. Waterstop-RX must wall
Applications include both vertical and be placed into adhesive prior to CETSEAL
horizontal non-moving concrete construction skinning over and curing. CETSEAL may be General Application Detail
joints, new to existing concrete construction, applied to damp surfaces, but not in standing
irregular surfaces, and around through-wall water.

www.cetco.com
North America: 847.851.1800 | 800.527.9948
TECHNICAL DATA

wATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP

Installation with REVO-FIX: REVO-FIX is a secure WATERSTOP-RX alone. Do not use any In conditions where severe ground water
steel mesh used to mechanically secure other adhesive or construction sealant, except chemical contamination exists, or is expected,
WATERSTOP-RX 101 into position using the CETSEAL, to secure Waterstop-RX. consult manufacturer for product chemical
accompanying supplied fasteners. Remove compatibility information.
release paper and place the WATERSTOP-RX Waterstop-RX is not designed, nor intended
on the concrete substrate. Then place REVO- to function as an expansion joint sealant.
FIX strips over the WATERSTOP-RX, lapping For precast concrete applications, contact
PACKAGING
RX-101: 30 m (100 ft./box)
the strip ends by 25 mm (1”) maximum. Nail manufacturer for product suitability and for
RX-101T: 36 m (120 ft./box)
through LAP with fastener supplied, and install any special installation requirements.
RX-102: 60 m (200 ft./box)
one fastener 300 mm (12”) on center along
CETSEAL and REVO-FIX are packaged
the REVO-FIX. Waterstop-RX products are designed
separately.
for structural concrete with a minimum of
End-to-end or end-to-side REVO-FIX junctions 20N/mm2 3,000 psi compressive strength.
are created by simple butt joints pressed Waterstop-RX 101 and RX-101T require a ACCESSORY PRODUCTS
firmly together. Start at junctions; do not minimum of 3” (75 mm) of concrete coverage. CETSEAL is a multi-purpose, single component
stretch WATERSTOP-RX to fit. Do not overlap Waterstop-RX 102 requires a minimum polyether moisture cure adhesive used to
waterstop. concrete coverage of 2” (50 mm). Waterstop- secure Waterstop-RX into position. Apply
RX should only be used in applications where a continuous bead of CETSEAL to substrate
the product is completely encapsulated within then install Waterstop-RX before CETSEAL
LIMITATIONS the concrete. skins over and cures. Adhesive yield will vary
Waterstop-RX is not a self-adhering
with use, substrate and application.
product. CETSEAL or REVO-FIX is required
Waterstop-RX should not be prehydrated
to secure Waterstop-RX to concrete,
by being subjected to submersion or
metal, or PVC (Pipe) surfaces. Mechanical
remain in extended contact with water
fasteners should be used with REVO-FIX to
prior to encapsulation in concrete. If the
secure WATERSTOP-RX 101; and fasteners
product exhibits considerable swell prior to
can be used in conjunction with CETSEAL.
encapsulation in the concrete, it must be
Mechanical fasteners should not be used to
replaced with new material.

WATERSTOP-RX PRODUCT TABLE

PRODUCT SIZE ROLL CROSS-SECTION SHAPE UNIT QTY/CARTON MIN CONCRETE
LENGTH COVERAGE
RX-101 25 x 19 mm (1” X 3/4”) 5 m (16’ 8”) Rectangle 30 m (100 LF) 75 mm (3”)
RX-101T 31 x 12 mm (1-1/4” X 1/2”) 6 m (20’) Trapezoid with Poly Scrim 36 m (120 LF) 75 mm (3”)
Reinforcement
RX-102 19 x 9 mm (3/4” x 3/8”) 10 m (33’ 4”) Half-Circle 60 m (200 LF) 50 mm (2”)

www.cetco.com
Form: TDS_Bentogrout_AM_201308_v1
North America: 847.851.1800 | 800.527.9948
TECHNICAL DATA

wATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP

5
LIMITED WARRANTY
FAST & E ASY Specifications and other information contained herein supersedes all
INSTALL ATION STEPS previously printed matter and are subject to change without notice.

All goods sold by seller are warranted to be free from defects in

STEP 1 material and workmanship. The foregoing warranty is in lieu of and
CLEAN SURFACE excludes all other warranties not expressly set forth herein, whether
expressed or implied by operation of law or otherwise, including but
not limited to any implied warranties of merchantability or fitness.

Seller shall not be liable for incidental or consequential losses,

damages or expenses, directly or indirectly arising for the sale,
handling or use of goods, or from any other case relating thereto,
REMOVE ALL DIRT AND DEBRIS
and seller’s liability hereunder in any case is expressly limited to the
replacement (in the form originally shipped) of goods not complying
STEP 2 with the agreement or at seller’s election, to the repayment of, or
APPLY crediting buyer with, an amount equal to the purchase price of such
ADHESIVE goods, whether such claims are for breach of warranty or negligence.

Any claim by buyer with reference to the goods sold hereunder for any
cause shall be deemed waived by buyer unless submitted to seller in
writing within thirty (30) days from the date buyer discovered or should
APPLY CETSEAL
of discovered, any claimed breach.

STEP 3 Minimum
75 mm (3”) Materials should be inspected and tested by purchaser prior to
PLACE their use if product quality is subject to verification after shipment.
Waterstop Performance guarantees are normally supplied by the applicator.

TYPICAL PROPERTIES
PROPERTY TEST METHOD VALUE
REMOVE RELEASE PAPER THEN PRESS Hydrostatic Head Resist- Independent Test 70 m (231 Ft.)
FIRMLY AGAINST CETSEAL. MAINTAIN ance
MIN. CONCRETE COVERAGE DEPTH Wet / Dry Cycling Independent Test No Effect
(25 Cycles @ 231 ft)
STEP 4 Adhesion to Concrete Independent Test Excellent
Using CETSEAL
BUTT COIL ENDS

TIGHTLY BUTT COIL ENDS TO FORM A

CONTINUOUS Waterstop. DO NOT
OVERLAP COIL ENDS

STEP 5 Waterstop-RX
concrete
POUR
CONCRETE

www.cetco.com
North America: 847.851.1800 | 800.527.9948
 TECHNICAL DATA

wATERSTOP-RX®
EXPANDING CONCRETE JOINT WATERSTOP

TYPICAL PRODUCT APPLICATIONS

Waterstop-RX 101 and RX 101T Waterstop-RX 102
• Vertical and horizontal concrete 200 mm (8”) thick or greater • Vertical concrete 150 mm (6”) thick or greater.
• Concrete with two rows of steel reinforcement • Horizontal concrete 100 mm (4”) thick or greater
• Shotcrete Foundation Walls • Concrete with one row of steel reinforcement
• High hydrostatic pressures • Slabs containing only wire mesh
• Tie-back plates and penetrations • Fountains / Planter Boxes / Curbs
• Penetrations

Install Waterstop-RX at all

Install Waterstop-RX at all wall pour joints
slab pour joints and connect
with wall joint installation to Reinforcing Steel
form continuous waterstop

Install Waterstop-RX at
footing/wall joint

Install Waterstop-RX SLAB JOINT SECTION DETAIL

inside of outer most
reinforcing steel

75 mm (3”) min Waterstop-RX Reinforced slab

concrete coverage (min 75 mm (3”) coverage)

Typical Waterstop-RX Foundation Detailing

Waterstop-RX Waterstop-RX
(min 75 mm (3”) coverage) Non-shrink grout (min 75 mm (3”) coverage)

Concrete
Pipe Pipe sleeve Pipe
Concrete
Cast-in-Place Penetration Sleeved Penetration Detail

North America: 847.851.1800 | 800.527.9948

© 2014 CETCO. IMPORTANT: The information contained herein supersedes all previous printed versions, and is believed to
be accurate and reliable. For the most up-to-date information, please visit www.CETCO.com. CETCO accepts no responsibility
for the results obtained throught application of this product. CETCO reserves the right to update information without notice.

April 2014 TDS_WATERSTOP-RX_AM_EN_201404_v1 www.CETCO.com