Service Manual PT

HYDROBOX
October 2020
No. OCH712
REVISED EDITION-C
SERVICE MANUAL
[Model Name]
EHSD-MED EHSC-MED EHSE-MED Revision:
• ERSD-VM6D, ERSD-
EHSD-VM2D EHSC-VM2D EHSE-YM9ED YM9D, ERSC-VM6D,
ERSC-YM9D and
EHSD-VM6D EHSC-VM6D ERSE-MED ERPX series have been
added.
EHSD-YM9D EHSC-YM9D ERSE-YM9ED • Some descriptions
have been modified in
EHSD-YM9ED EHSC-YM9ED EHPX-VM2D REVISED EDITION-C.
EHSD-TM9D EHSC-TM9D EHPX-VM6D OCH712B is void.
ERSD-MED ERSC-MED EHPX-YM9D Note:

•This manual describes
ERSD-VM2D ERSC-VM2D EHPX-MED service data of
Hydrobox only.
ERSD-VM6D ERSC-VM6D EHPX-YM9ED
ERSD-YM9D ERSC-YM9D ERPX-MD
ERPX-VM2D
ERPX-VM6D
ERPX-YM9D
[Service Ref.]
Refer to page 2.
CONTENTS
1. REFERENCE MANUAL.................................... 3
2. SAFETY PRECAUTION.................................... 4
3. SPECIFICATIONS............................................. 6
4. PART NAMES AND FUNCTIONS ................... 8
5. OUTLINES AND DIMENSIONS........................ 9
6. WIRING DIAGRAM.......................................... 11
7. FIELD WIRING................................................ 17
8. WATER SYSTEM DIAGRAM.......................... 19
9. CONTROLS.................................................... 22
10. TROUBLESHOOTING.................................... 43
11. DISASSEMBLY PROCEDURE....................... 60
MAIN REMOTE 12. SUPPLEMENTARY INFORMATION.............. 80

HYDROBOX 13. SERVICE AND MAINTENANCE.................... 81
CONTROLLER
PARTS CATALOG (OCB712)

[Service Ref.]
EHSD-MED.UK
EHSD-VM2D.UK
EHSD-VM6D.UK
EHSD-YM9D.UK
EHSD-YM9ED.UK
EHSD-TM9D.UK
ERSD-MED.UK
ERSD-VM2D.UK
ERSD-VM6D.UK
ERSD-YM9D.UK
EHSC-MED.UK
EHSC-VM2D.UK
EHSC-VM6D.UK
EHSC-YM9D.UK
EHSC-YM9ED.UK
EHSC-TM9D.UK
ERSC-MED.UK
ERSC-VM2D.UK
ERSC-VM6D.UK
ERSC-YM9D.UK
EHSE-MED.UK
EHSE-YM9ED.UK
ERSE-MED.UK
ERSE-YM9ED.UK
EHPX-VM2D.UK
EHPX-VM6D.UK
EHPX-YM9D.UK
EHPX-MED.UK
EHPX-YM9ED.UK
ERPX-MD.UK
ERPX-VM2D.UK
ERPX-VM6D.UK
ERPX-YM9D.UK
OCH712C 2
1 REFERENCE MANUAL
OUTDOOR UNIT'S SERVICE MANUAL

Service Ref. Service Manual No.
SUZ-SWM40VA.TH
OCH718
SUZ-SWM60VA.TH
OCB718
SUZ-SWM80VA.TH
PUHZ-FRP71VHA2 OCH665
PUHZ-FRP71VHA2R1 OCB665
PUHZ-SW120VHAR5(-BS).UK OCH533
PUHZ-SW120YHAR5(-BS).UK OCB533
OCH526
PUHZ-SHW140YHAR5(-BS).UK
OCB526
PUHZ-SW160YKAR1(-BS).UK OCH583
PUHZ-SW200YKAR1(-BS).UK OCB583
OCH594
PUHZ-SHW230YKA2R2
OCB594
PUHZ-SHW80VAA(-BS).UK
PUHZ-SHW80YAA(-BS).UK
PUHZ-SHW112VAA(-BS).UK
PUHZ-SHW112YAA(-BS).UK
PUHZ-SW75VAA(-BS).UK OCH651
PUHZ-SW75YAA(-BS).UK OCB651
PUHZ-SW75VAA-SC.UK
PUHZ-SW75YAA-SC.UK
PUHZ-SW100VAA(-BS).UK
PUHZ-SW100YAA(-BS).UK
Split model
PUMY-P112VKM4R4(-BS).UK
PUMY-P112YKM4R4(-BS).UK
OCH673
OCB673
PUMY-P112YKME4R4(-BS).UK
PUD-SWM60VAA(-BS).UK
PUD-SWM80YAA(-BS).UK
OCH694
PUD-SHWM60VAA(-BS).UK
OCB694
PUD-SHWM80YAA(-BS).UK
PUZ-WM50VHA(-BS).UK
PUZ-WM60VAA(-BS).UK
PUZ-WM85VAA(-BS).UK OCH727
PUZ-WM85YAA(-BS).UK OCB727
Packaged model PUZ-WM112VAA(-BS).UK
PUZ-WM112YAA(-BS).UK
PUZ-HWM140VHA(-BS) OCH748
PUZ-HWM140YHA(-BS) OCB748
OCH712C 3
2 SAFETY PRECAUTION
Please read the following safety precautions carefully.
WARNING: CAUTION:
Precautions that must be observed to prevent injuries or death. Precautions that must be observed to prevent damage to unit.
Mitsubishi Electric is not responsible for the failure of locally-supplied parts.
• Be sure to perform periodical maintenance.

• Be sure to follow your local regulations.
• Be sure to follow the instructions provided in this manual.
MEANINGS OF SYMBOLS DISPLAYED ON THE UNIT

This mark is for R32 refrigerant only. Refrigerant type is written on nameplate of outdoor unit.
WARNING In case that refrigerant type is R32, this unit uses a flammable refrigerant.
(Risk of fire) If refrigerant leaks and comes in contact with fire or heating part, it will create harmful gas and there is risk of fire.
Read the OPERATION MANUAL carefully before operation.
Service personnel are required to carefully read the OPERATION MANUAL and INSTALLATION MANUAL before operation.
Further information is available in the OPERATION MANUAL, INSTALLATION MANUAL, and the like.
WARNING
Mechanical
The hydrobox and outdoor units must not be installed, disassembled, relocated, altered or repaired by the user. Ask an authorised installer or technician. If the
unit is installed improperly or modified after installation by the user water leakage, electric shock or fire may result.
The outdoor unit should be securely fixed to a hard level surface capable of bearing its weight.
The hydrobox should be positioned on a hard vertical surface capable of supporting its filled weight to prevent excessive sound or vibration.
Do not position furniture or electrical appliances below the outdoor unit or hydrobox.
The discharge pipework from the emergency/safety devices of the hydrobox should be installed according to local law.
Only use accessories and replacement parts authorised by Mitsubishi Electric ask a qualified technician to fit the parts.
Electrical
All electrical work should be performed by a qualified technician according to local regulations and the instructions given in this manual.
The units must be powered by a dedicated power supply and the correct voltage and circuit breakers must be used.
Wiring should be in accordance with national wiring regulations. Connections must be made securely and without tension on the terminals.
Earth unit correctly.
Discharge the condenser before the work involving the electric parts.
General
Keep children and pets away from both the hydrobox and outdoor units.
Do not use the hot water produced by the heat pump directly for drinking or cooking. This could cause illness to the user.
Do not stand on the units.
Do not touch switches with wet hands.
Annual maintenance checks on both the hydrobox and the outdoor unit should be conducted by a qualified person.
Do not place containers with liquids on top of the hydrobox. If they leak or spill onto the hydrobox damage to the unit and/or fire could occur.
Do not place any heavy items on top of the hydrobox.
When installing, relocating, or servicing the hydrobox, use only the heat pump’s specified refrigerant to charge the refrigerant lines. Do not mix it with any
other refrigerant and do not allow air to remain in the lines. If air is mixed with the refrigerant, then it can be the cause of abnormal high pressure in the refriger-
ant line, and may result in an explosion and other hazards.
The use of any refrigerant other than that specified for the system will cause mechanical failure or system malfunction or unit breakdown. In the worst case,
this could lead to a serious impediment to securing product safety.
In heating mode, to avoid the heat emitters being damaged by excessively hot water, set the target flow temperature to a minimum of 2ºC below the maximum
allowable temperature of all the heat emitters. For Zone2, set the target flow temperature to a minimum of 5ºC below the maximum allowable flow temperature
of all the heat emitters in Zone2 circuit.
Do not install the unit where combustible gases may leak, be produced, flow, or accumulate. If combustible gas accumulates around the unit, fire or explosion may
result.
Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
The appliance shall be stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an operating
electric heater).
Do not pierce or burn.
Be aware that refrigerants may not contain an odour.
Pipe-work shall be protected from physical damage.
The installation of pipe-work shall be kept to a minimum.
Compliance with national gas regulations shall be observed.
Keep any required ventilation openings clear of obstruction.
Do not use low temperature solder alloy in the case of brazing the refrigerant pipes.
OCH712C 4
CAUTION
Use clean water that meets local quality standards on the primary circuit.
The outdoor unit should be installed in an area with sufficient airflow according to the diagrams in the outdoor unit installation manual.
The hydrobox should be located inside to minimise heat loss.
Water pipe-runs on the primary circuit between outdoor and indoor unit should be kept to a minimum to reduce heat loss.
Ensure condensate from outdoor unit is piped away from the base to avoid puddles of water.
Remove as much air as possible from water circuit.
Refrigerant leakage may cause suffocation. Provide ventilation in accordance with EN378-1.
Be sure to wrap insulation around the piping. Direct contact with the bare piping may result in burns or frostbite.
Never put batteries in your mouth for any reason to avoid accidental ingestion.
Battery ingestion may cause choking and/or poisoning.
Install the unit on a rigid structure to prevent excessive sound or vibration during operation.
If power to the hydrobox is to be turned off (or system switched off) for a long time, the water should be drained.
Preventative measures should be taken against water hammer, such as installing a Water Hammer Arrestor on the primary water circuit, as directed by the man-
ufacturer.
In order to prevent condensation on emitters, adjust flow temperature appropriately and also set the lower limit of the flow temperature on site.
As for the handling of refrigerant, refer to the outdoor unit installation manual.
[1] Cautions for service

(1) Perform service after recovering the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) If moisture or foreign matter might have entered the refrigerant piping during service, ensure to remove them.
[2] Additional refrigerant charge

When charging directly from refrigerant cylinder
(1) Check that cylinder for R410A or R32 on the market is syphon type.
(2) Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)
Unit
Electronic weighing scale
[3] Service tools

Use the service tools below as exclusive tools for R410A or R32 refrigerant.
No. Tool name Specifications
· R410A or R32
1 Gauge manifold · Use the existing fitting specifications. (UNF1/2)
· Use high-tension side pressure of 5.3 MPa·G or over.
· R410A or R32
2 Charge hose
· Use pressure performance of 5.09 MPa·G or over.
3 Electronic weighing scale —
4 Gas leak detector · Use the detector for R134a, R407C, R410A or R32
5 Adaptor for reverse flow check · Attach on vacuum pump.
6 Refrigerant charge base —
· R410A or R32 · Top of cylinder (Pink)
7 Refrigerant cylinder
· Cylinder with syphon
8 Refrigerant recovery equipment —
OCH712C 5
EHSD- EHSD- EHSD- EHSD- EHSD- EHSD- ERSD- ERSD- ERSD- ERSD- EHSC- EHSC- EHSC- EHSC- EHSC- EHSC- ERSC- ERSC- ERSC- ERSC-
Model name
3
MED VM2D VM6D YM9D YM9ED TM9D MED VM2D VM6D YM9D MED VM2D VM6D YM9D YM9ED TM9D MED VM2D VM6D YM9D
Overall unit dimensions (Height × Width × Depth) 800 × 530 × 360 mm

Weight (empty) 36 kg 43 kg 44 kg 44 kg 40 kg 44 kg 38 kg 44 kg 43 kg 44 kg 40 kg 47 kg 48 kg 48 kg 43 kg 48 kg 41 kg 48 kg 48 kg 48 kg
Weight (full) 38 kg 48 kg 49 kg 49 kg 45 kg 49 kg 39 kg 50 kg 49 kg 50 kg 42 kg 53 kg 54 kg 54 kg 50 kg 54 kg 44 kg 54 kg 54 kg 55 kg
Water volume of heating circuit in the unit *1 1.7 L 5.2 L 5.2 L 5.2 L 5.2 L 5.2 L 1.7 L 5.2 L 5.2 L 5.2 L 2.6 L 6.1 L 6.1 L 6.1 L 6.1 L 6.1 L 2.6 L 6.1 L 6.1 L 6.1 L
Nominal volume — 10 L — 10 L — 10 L — 10 L — 10 L — 10 L
Unvented expansion
vessel(Primary heating) Charge pressure 0.1 MPa 0.1 MPa
— 0.1 MPa (1 bar) — — 0.1 MPa (1 bar) — 0.1 MPa (1 bar) — — 0.1 MPa (1 bar)
(1 bar) (1 bar)
Control thermistor 80°C
Water
OCH712C
circuit Pressure relief valve 0.3 MPa (3 bar)
Safety (Primary)
Flow sensor Min. flow 5.0 L/min (See table 10.6.1 about water flow rate range)
device
Booster Manual reset thermostat — 90°C — 90°C — 90°C — 90°C
heater Thermal Cut-out (for dry run prevention) — 121°C — 121°C — 121°C — 121°C
Water (primary circuit) 28 mm / Compression G1-B 28 mm / Compression G1-B
Connections Refrigerant Liquid Ø6.35 mm Ø9.52 mm
(R32/ R410A) Gas Ø12.7 mm Ø15.88 mm
Flow Heating 20 - 60°C
temperature Cooling — 5 - 25°C — 5 - 25°C
Target temperature
SPECIFICATIONS
range Heating 10 - 30°C

Room
temperature Cooling —
Ambient *2 0 - 35°C ( 80 %RH)
Guaranteed
operating range Outdoor Heating See outdoor unit spec table.
temperature Cooling — *3 — *3
Power supply ~/N, 230 V, 50 Hz
Control board (Phase, voltage, frequency)
(Including 3 Breaker
pumps) (*when powered from 10 A
6
independent source)
Power supply 3~, ~/N, 3~, ~/N, 3~, ~/N, 3~,
Electrical data (Phase, voltage, — ~/N, 230 V, 3~, 400 V, 3~, 400 V,
230 V, — 230 V, 400 V, — 230 V, 230 V, — 230 V, 400 V,
frequency) 50 Hz 50 Hz 50 Hz
50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz
Booster 2 kW 3 kW 3 kW 2 kW 3 kW 2 kW 3 kW 3 kW 2 kW 3 kW
heater Capacity — 2 kw — 2 kW — 2 kW — 2 kW
+4 kW +6 kW +6 kW +4 kW +6 kW +4 kW +6 kW +6 kW +4 kW +6 kW
Current — 9A 26 A 13 A 23 A — 9A 26 A 13 A — 9A 26 A 13 A 23 A — 9A 26 A 13 A
Breaker — 16 A 32 A 16 A 32 A — 16 A 32 A 16 A — 16 A 32 A 16 A 32 A — 16 A 32 A 16 A
Sound power level 41 dB(A) 40 dB(A) 40 dB(A)
<Table 3.1>
*1 Piping to Expansion vessel is not included in this value.
*2 The environment must be frost-free.
*3 See outdoor unit spec table. (min. 10°C)
Cooling mode is not available in low outdoor temperature.
If you use our system in cooling mode at the low ambient temperature (10°C or below), there are some risks of plate heat exchanger damages by frozen water.
Model name ERSE-YM9ED ERSE-MED EHSE-YM9ED EHSE-MED EHPX-MED EHPX-VM2D EHPX-VM6D EHPX-YM9D EHPX-YM9ED ERPX-MD ERPX-VM2D ERPX-VM6D ERPX-YM9D
Overall unit dimensions (Height × Width × Depth) 950 × 600 × 360 mm 800 × 530 × 360 mm
Weight (empty) 64 kg 62 kg 63 kg 61 kg 25 kg 32 kg 33 kg 33 kg 28 kg 30 kg 33 kg 34 kg 35 kg
Weight (full) 74 kg 72 kg 73 kg 71 kg 26 kg 36 kg 37 kg 38 kg 32 kg 31 kg 37 kg 38 kg 39 kg
Water volume of heating circuit in the unit *1 10.0 L 10.0 L 10.0 L 10.0 L 1.0 L 4.5 L 4.5 L 4.5 L 4.5 L 1.0 L 4.5 L 4.5 L 4.5 L
Unvented expansion Nominal volume — — — — — 10 L — 10 L
vessel(Primary heating) Charge pressure — — — — — 0.1 MPa (1 bar) — 0.1 MPa (1 bar)
Control thermistor 80°C
Water
circuit Pressure relief valve 0.3 MPa (3 bar) — 0.3 MPa (3 bar)
Safety (Primary)
Flow sensor Min. flow 5.0 L/min (See table 10.6.1 about water flow rate range)
OCH712C
device
Booster Manual reset thermostat 90°C — 90°C — — 90°C — 90°C
heater Thermal Cut-out (for dry run prevention) 121°C — 121°C — — 121°C — 121°C
Water (primary circuit) G1-1/2-B 28 mm / Compression G1-B
Connections Refrigerant Liquid Ø9.52 mm — — — — — — — — —
(R32/ R410A) Gas Ø25.4 mm (Brazing) — — — — — — — — —
Flow Heating 20 - 60°C
temperature Cooling — 5 - 25°C
Target temperature
range Heating 10 - 30°C
Room
temperature Cooling —
Ambient *2 0 - 35°C ( 80 %RH)
Guaranteed
operating range Outdoor Heating See outdoor unit spec table
temperature Cooling *3 — — *3
Power supply ~/N, 230 V, 50 Hz
7
Control board (Phase, voltage, frequency)
(Including 3 Breaker
pumps) (*when powered from 10 A
independent source)
Electrical data Power supply 3~, 400 V, 3~, 400 V, ~/N, 230 V, 3~, 400 V, ~/N, 230 V, 3~, 400 V,
— — — —
(Phase, voltage, frequency) 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz
Booster 3 kW 3 kW 2 kW 3 kW 2 kW 3 kW
Capacity — — — 2 kW — 2 kW
heater +6 kW +6 kW +4 kW +6 kW +4 kW +6 kW
Current 13 A — 13 A — — 9A 26 A 13 A — 9A 26 A 13 A
Breaker 16 A — 16 A — — 16 A 32 A 16 A — 16 A 32 A 16 A
Sound power level 45 dB(A) 40 dB(A)
<Table 3.2>
*1 Piping to Expansion vessel is not included in this value.
*2 The environment must be frost-free.
*3 See outdoor unit spec table. (min. 10°C)
Cooling mode is not available in low outdoor temperature.
If you use our system in cooling mode at the low ambient temperature (10°C or below), there are some risks of plate heat exchanger damages by frozen water.
4 PART NAMES AND FUNCTIONS
<E*PX-*M**D> (Packaged model system)
16
12
13
7
9
4 14
10
15
<Figure 4.1> <Figure 4.2>
<E*S*-*M**D> (Split model system) <E*SE-*M*ED> (Split model system)
16
3 12
12
13 6
6 4 7
3
8
5 8
4
17 9
5 9
7
14
14
15 15
11
11
<Figure 4.3> <Figure 4.4>

No. Part name EHPX-*M*(E)D ERPX-MD ERPX-*M*D EHS*-MED EHS*-*M*D EHS*-YM9ED ERS*-*M*(E)D ERS*-MED
1 Control and electrical box Note:
2 Main remote controller For installation of all E***-*M*ED
3 Plate heat exchanger (Refrigerant - Water) - - - models, make sure to install
4 Water circulation pump 1 a suitably sized primary-side
5 Pump valve expansion vessel. (See figure 8.1
6 Air vent (manual) - - - and 8.2 for further guidance)
7 Drain cock (Primary circuit) -
8 Booster heater 1,2 - - - *1 E
HPX-YM9ED and
9 Flow sensor EHPX-MED are not included.
10 Manometer *2 ERSE-YM9ED is not included.
11 Pressure relief valve (3 bar) - - - *3 Only 2HP (E*SD) model.
12 Automatic air vent
13 Expansion vessel *1 - - *2 -
14 Strainer valve
15 Drain pan - - - -
16 Pressure relief valve (5 bar) *1 - - *2 -
17 Pressure sensor - - - *3 *3 *3 *3 *3
<Table 4.1>
OCH712C 8
5 OUTLINES AND DIMENSIONS
5-1. Technical Drawings <Unit: mm>
530
HOOK
AUTO AIR VENT
FRONT PANEL
EARTH LEAKAGE BREAKER
BACK PANEL SUPPORT

800
TERMINAL BED
578
MAIN CONTROLLER
242
MANOMETER
110
100±5
PRESSURE RELIEF VALVE
G1/2
(242)
<Front> <Side> <Rear>
<EHPX> (Packaged model system for heating) <ERPX> (Packaged model system for heating and cooling)
H
H I
(348)
(348)
357
357
291
291
263
263
183
103
103
48 48
78 E B A F 60
86 86 E B A
124 124
163 145
334 163
419 248
361
446
<View from below> <View from below>
Letter Pipe description Connection size/type
28mm/Compression (EHSD/EHSC/EHPX-*)
Space heating/Indirect DHW tank (primary)
A G1 nut (ERSD/ERSC/ERPX-*)
RETURN connection
G1-1/2 nut (E*SE-*)
28mm/Compression (EHSD/EHSC/EHPX-*)
Space heating/Indirect DHW tank (primary)
B G1 nut (ERSD/ERSC/ERPX-*)
FLOW connection
G1-1/2 nut (E*SE-*)
6.35 mm/Flare (E*SD-*)
C Refrigerant (Liquid) 9.52 mm/Flare (E*SC-*) Warning
9.52 mm/Flare (E*SE-*) • R efrigerant pipes connection shall be accessible for
12.7 mm/Flare (E*SD-*) maintenance purposes.
15.88 mm/Flare (E*SC-*) • In the case of reconnecting the refrigerant pipes after
D Refrigerant (Gas) detaching, make the flared part of pipe re-fabricated.
Brazing connection I.D.
ø25.4 (E*SE-*)
28 mm/Compression (EHPX-*)
E Flow connection FROM heat pump
G1 nut (ERPX-*)
28 mm/Compression (EHPX-*)
F Return connection TO heat pump
G1 nut (ERPX-*)
Discharge pipe (by installer) from pressure
G G1/2” female (valve port within hydrobox casing)
relief valve
Electrical cable inlets For inlets and , run high-voltage wires including power cable, indoor-outdoor
cable, and external output wires.
H For inlets and , run low-voltage wires including external input wires and
thermistor wires.
For a wireless receiver (option) cable, use inlet .
I Drain socket O.D. ø20
<Table 5.1>
OCH712C 9
<Unit: mm>
<EHS*> (Split model system for heating) <ERS*> (Split model system for heating and cooling)
H B A G H G
(348)
(348)
357
357
291
291
263
263
242
242
164
134
98
94
48 48
86 C D B 86
I C D
124 124
153 133
163 163
213 223
310 308
395 365
461
461
<View from below> <View from below>

<E*SE> (Split model system for heating/ heating and cooling)
600 HOOK
AUTO AIR VENT
FRONT PANEL
EARTH LEAKAGE BREAKER

950
TERMINAL BED
578
BACK PANEL SUPPORT
MAIN CONTROLLER
242
110
MANOMETER PRESSURE
40
100±5
RELIEF VALVE
SPACE HEATING FLOW G1/2
REFRIGERANT (ISO 228-1 G1-1/2-B)
A
(LIQUID 3/8) (242)
SPACE HEATING RETURN
REFRIGERANT(GAS) (ISO 228-1 G1-1/2-B)
*REFER TO DETAIL VIEW A.
<Front> <Side> <Rear>

I
H A B G
DEATIL VIEW A
ADD AN ACCESSORY
TO REFRIGERANT GAS
(348)
357
PIPE. (FLARING) 3/4F REFRIGERANT (GAS)

291
CONNECTION (BRAZING)
263
242
I.D. ø 25.4
193
124
110
48
86
124
163 C D
187
249
300
367
492
541
<View from below>
OCH712C 10
6 WIRING DIAGRAM
6-1. EHSD-MED.UK, ERSD-MED.UK, EHSC-MED.UK, ERSC-MED.UK,
EHSE-MED.UK, ERSE-MED.UK, EHPX-MED.UK, ERPX-MD.UK
CNPWM CN01
(WH) (BK) Indoor unit powered Indoor unit powered
1 1
<How to use TBO.1 to 4> via outdoor unit by independent source
3 Connect them using either way as shown below.
F1 To outdoor Power supply To outdoor
3 3 5 unit ~/N 230V 50Hz unit
F2 Tool
CNP1 Tool
(WH) TBO.1
1 X1
1
BREAKER
M
CIRCUIT
1~ 2
M 3
1~ MP1 X2
M 3 Conductor Conductor
2WV2b 1~ 4 L N S1 S2 S3 TB1 L N S1 S2 S3 TB1
MP2 X3 Outline view Top view
M 5
GNYE
GNYE
1~
RD
OG
RD
OG
BU
BU
YE
YE
6
MP3
1 X14 FTC board
M
OG
YE
1~
OG
1
YE
MP4 3 1 TBO.1 CN01
CNP4 (BK) 3
(RD) 2
3 5
1 CNP1
X5A
TBO.2 4 (WH) CN01 1 CN01 1
1 3 F2 F1 (BK) 3 (BK) 3
Close 5 IEC T6.3AL250V IEC T10AL250V
M N 5 5
1~ Open 2 6
X5B 1 1
MXV 3 1 CN3C
CNP4
1 TBO.2 (BU) 3
4 3 (RD) LED1
M 2 BN BN
1~ 5 SW5 1 CN3C 1 CN3C 1
3 CNPWM OG OG
3WV 6 X4 (BU) 3 (BU) 3
4 (WH) 3
CNV1
(WH) 5 8
4 5 6
1 6 1 1
TBO.2 1
3 CNV1
M 3 CN851
1 TBO.3 (WH)
1~ 5 5 SW4 (BK)
2
2WV1
TBO.3 3
8
X10 4 6
Signal output 1
5 1
(Boiler) 2 1
X16 6 CNRF Wireless receiver
Signal output 3
7 SW3
(WH) (Option)
(thermo on) 4 LED2 5
8
X11
Signal output 5
(Error) 1 TBO.4 1
6 8 CN105 WiFi adapter
X12 2
7 1 LED3 (RD) (Option)
Signal output 3 5
(Defrost) 8 4
TBO.4 5 SW2 1
X15
Signal output 1 6 CNIT
(Comp. on) 7 (BU)
2 5
X13 8 8
M 3 1 CNIH 1
1~ 4 (OG) CN22 1
3 1 (BU) 2
2WV2a X9
5
1 1 CNBHT SW1 SW6
6 CNBC CN108
X8 (GY) (BK)
3 3
Signal output 7 5
(Cooling) LED4
8 8
1
CNBHT 3
(BK) CNBH
1 5 (WH)
7
3
TAB1
CNBC
(GY)
1
3
CNBH CN401 CN1A CNW5 CNW12 CN21 CN20
(WH)
X6 (WH) (WH) (BU) (RD) (YE) (RD)
1
1 1 1 1 1 1
3
X7 3 2
5 4 4 4 4
7
87654321 87654321 87654321 87654321 87654321 87654321
TBI.1 TBI.2 TBI.3 TBI.4 TBI.5 TBI.6
TAB1 CN401 CNW5 CNW12 CN21 CN20

(WH) (BU) (RD) (YE) (RD) TBI.1 TBI.2 TBI.3 TBI.4 TBI.5 TBI.6
8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1
1 4 1 4 1 4 1 3 1 2
- + - + - + + - CN1A
(WH)
CN22
(BU)
1 4 2 1
Main remote
V
controller
Sensor *
Pressre
Sensor
Flow
t° t° t° t° t° t° t° t° t° t° t°
THW5B THW1 THW2 TH2 TH1

TH IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN10 IN8 IN9 IN11 IN12 OUTA1 THW6 THW7 THW8 THW9 THWB1 THW10
Table 1 Signal Inputs

Symbol Name
Name Terminal block Connector Item OFF (Open) ON (Short)
TB1 Terminal block <Power supply, Outdoor unit>
Refer to SW2-1 in
IN1 TBI.1 7-8 — Room thermostat 1 input *1 ECB1 Earth leakage circuit breaker for booster heater
<Table 6.6.1 DIP Switch Functions>.
Refer to SW2-2 in MP1 Water circulation pump 1(Space heating and DHW)
IN2 TBI.1 5-6 — Flow switch 1 input
<Table 6.6.1 DIP Switch Functions>. MP2 Water circulation pump 2
Refer to SW3-2 in (Space heating for Zone1)(Local supply)
IN3 TBI.1 3-4 — Flow switch 2 input (Zone1)
Heat source OFF/ (Space heating for Zone2)(Local supply)
IN4 TBI.1 1-2 — Demand control input Normal
Boiler operation *3 MP4 Water circulation pump 4 (DHW)(Local supply)
Standard opera- Heater operation/ 3WV(2WV1) 3-way valve (2-way valve 1)(Local supply)
IN5 TBI.2 7-8 — Outdoor thermostat input *2
tion Boiler operation *3
2WV2a 2-way valve (For Zone 1)(Local supply)
Refer to SW3-1 in
IN6 TBI.2 5-6 — Room thermostat 2 input *1 2WV2b 2-way valve (For Zone 2)(Local supply)
Refer to SW3-2 in MXV Mixing valve (Local supply)
<Table 6.6.1 DIP Switch Functions>. BHT Thermostat for booster heater
IN8 TBI.3 7-8 — Electric energy meter 1 BHF Thermal fuse for booster heater
IN9 TBI.3 5-6 — Electric energy meter 2 BH1 Booster heater 1
IN10 TBI.2 1-2 — Heat meter BH2 Booster heater 2
Refer to installation manual.
IN11 TBI.3 3-4 —
Smart grid ready input BHC1 Contactor for booster heater 1
IN12 TBI.3 1-2 —
INA1 TBI.4 1-3 CN1A Flow sensor BHC2 Contactor for booster heater 2
BHCP Contactor for booster heater protection
*1. Set the ON/OFF cycle time of the room thermostat for 10 minutes or more;
otherwise the compressor may be damaged. TH1 Thermistor (Room temp.)(Option)
*2. If using outdoor thermostat for controlling operation of heaters, the lifetime of the heaters and TH2 Thermistor (Ref. liquid temp.)
related parts may be reduced.
THW1 Thermistor (Flow water temp.)
*3. To turn on the boiler operation, use the main remote controller to select “Boiler” in “External
input setting” screen in the service menu. THW2 Thermistor (Return water temp.)
Table 2 Outputs THW5B Thermistor (DHW tank water temp.)(Option)
Name Terminal block Connector Item OFF ON THW6
Water circulation pump 1 output THW7 Thermistor (Zone1 return temp.)(Option)
OUT1 TBO.1 1-2 CNP1 OFF ON
(Space heating/cooling & DHW) THW8
OUT2 TBO.1 3-4 — OFF ON
(Space heating/cooling for Zone1) THW10 Thermistor (Mixing tank temp.)(Option)
Water circulation pump 3 output
THWB1
OUT3 TBO.1 5-6 — (Space heating/cooling for Zone2) *1 OFF ON
2-way valve 2b output *2 IN1 Room thermostat 1 (Local supply)
TBO.2 4-6 CNV1 3-way valve (2-way valve) output IN2 Flow switch 1 (Local supply)
OUT4 Heating DHW
— CN851 3-way valve output IN3 Flow switch 2 (Local supply)
TBO.2 1-2 Close IN4 Demand control (Local supply)
OUT5 — Mixing valve output *1 Stop
TBO.2 2-3 Open IN5 Outdoor thermostat (Local supply)
OUT6 — CNBH 1-3 Booster heater 1 output OFF ON IN6 Room thermostat 2 (Local supply)
OUT7 — CNBH 5-7 Booster heater 2 output OFF ON
IN7 Flow switch 3 (Local supply)
OUT8 TBO.4 7-8 — Cooling signal output OFF ON
IN8 Electric energy meter 1 (Local supply)
OUT9 TBO.4 5-6 CNIH Immersion heater output OFF ON
OUT10 TBO.3 1-2 — Boiler output OFF ON IN9 Electric energy meter 2 (Local supply)
OUT11 TBO.3 5-6 — Error output Normal Error IN10 Heat meter (Local supply)
OUT12 TBO.3 7-8 — Defrost output Normal Defrost IN11
Smart grid ready input (Local supply)
OUT13 TBO.4 3-4 — 2-way valve 2a output *2 OFF ON IN12
Water circulation pump 4 output INA1 Flow sensor
OUT14 — CNP4 OFF ON
(DHW) FLOW TEMP. CONTROLLER (FTC)
OUT15 TBO.4 1-2 — Comp. ON signal OFF ON
TBO.1−4 Terminal block <Outputs>
OUT16 TBO.3 3-4 — Thermo ON signal OFF ON
OUTA1 TBI.4 7-8 — Analog output 0V-10V TBI.1−6 Terminal block <Signal Inputs, Thermistor>
F1 Fuse (IEC T10AL250V)
Do not connect to the terminals that are indicated as “—” in the “T
*1. For 2-zone temperature control. F2 Fuse (IEC T6.3AL250V)
*2. For 2-zone valve ON/OFF control. SW1−6 DIP switch *See Table 6.6.1
X1−16 Relay
LED1 Power supply (FTC)
LED2 Power supply (Main remote controller)
LED3 Communication (FTC-Outdoor unit)
LED4 Reading or writing data to SD card
CNPWM Pump speed control signal for MP1
CN108 SD card connector
OCH712C 11
6-2. EHSD-VM2D.UK, ERSD-VM2D.UK, EHSC-VM2D.UK, ERSC-VM2D.UK, EHPX-VM2D.UK, ERPX-VM2D.UK
CNPWM CN01
Power supply 1 1
<How to use TBO.1 to 4> via outdoor unit by independent source
to Booster heater F1
3 Connect them using either way as shown below. To outdoor Power supply To outdoor
3
~/N 230V 50Hz 3 5 unit ~/N 230V 50Hz unit
F2 Tool
CNP1 Tool
TBO.1
L N (WH)
1 X1
(1) (3) 1
BREAKER
M
CIRCUIT
1~ 2
M 3
1~ MP1 X2
ECB1 2WV2b 1~ 4 L N S1 S2 S3 TB1 L N S1 S2 S3 TB1
MP2 X3 Outline view Top view
M 5
GNYE
GNYE
1~
RD
OG
RD
OG
BU
BU
YE
YE
6
2 4 MP3
1 X14 FTC board
M
RD
BU
OG
YE
1~
OG
1
YE
MP4 3 1 TBO.1 CN01
CNP4 (BK) 3
1 3 5 A1 (RD) 2
BHCP 3 1 CNP1
5
X5A
TBO.2 4 (WH) CN01 1 CN01 1
1 3 F2 F1 (BK) 3 (BK) 3
M N 5 5
2
2 4 6 A2 1~ Open X5B
6
1 1
MXV 3 1 CN3C
CNP4
1 TBO.2 (BU) 3
RD M
4
2
3 (RD) LED1
BN BN
BU 1~ 5 SW5 1 CN3C 1 CN3C 1
X4 3 CNPWM OG OG
3WV 6 (BU) 3 (BU) 3
4 (WH) 3
CNV1 5
BHC1 4 5 6 1
(WH) 8
1
6 1
1 3 5 A1
GY
GY
TBO.2 1
3 CNV1
M 3 CN851
1 TBO.3 (WH)
1~ 5 5 SW4 (BK)
2
2WV1
TBO.3 3
8
X10 4 6
Signal output 1
5 1
(Boiler) 2 1
2 4 6 A2 X16 6 CNRF Wireless receiver
Signal output 3
7 SW3
(WH) (Option)
VT
VT

8
X11
Signal output 5
(Error) 1 TBO.4 1
WH/No.1
WH/No.2

X12 2
Signal output 3 5
(Defrost) 8 4
TBO.4 5 SW2 1
X15
(Comp. on) 7 (BU)
2 5
BH1 X13 8 8
M 3 1 CNIH 1
2 2 1~ 4 3
(OG) 1
CN22 1
2WV2a X9 (BU) 2
5
BHF BHT 6
1 CNBC 1 CNBHT SW1 SW6
CN108
X8 (GY) (BK)
3 3
Signal output 7 5
(Cooling) LED4
WH
WH
8 8
1
CNBHT 3
(BK) CNBH
1 5 (WH)
2
2 1
3
7
CNBHT TAB1
3 CNBC
(BK) (GY)
1
2 1
CNBC 3
3 (GY) CNBH CN401 CN1A CNW5 CNW12 CN21 CN20
(WH)
1 X6 (WH) (WH) (BU) (RD) (YE) (RD)
2 1
1 1 1 1 1 1
3 3
CNBH 5
X7
4 4 4 4 3 2
(WH)
7
87654321 87654321 87654321 87654321 87654321 87654321

8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1
1 4 1 4 1 4 1 3 1 2
- + - + - + + - CN1A
(WH)
CN22
(BU)
1 4 2 1
Main remote
V
controller
Sensor *
Pressre
Sensor
Flow
t° t° t° t° t° t° t° t° t° t° t°


Symbol Name
Name Terminal block Connector Item OFF (Open) ON (Short)
TB1 Terminal block <Power supply, Outdoor unit>
Refer to SW2-1 in
Boiler operation *3 MP4 Water circulation pump 4 (DHW)(Local supply)
tion Boiler operation *3 2WV2a 2-way valve (For Zone 1)(Local supply)
Refer to SW3-1 in
IN6 TBI.2 5-6 — Room thermostat 2 input *1 2WV2b 2-way valve (For Zone 2)(Local supply)
IN7 TBI.2 3-4 — Flow switch 3 input (Zone2) BHT Thermostat for booster heater
IN10 TBI.2 1-2 — Heat meter BHC1 Contactor for booster heater 1
IN11 TBI.3 3-4 — BHCP Contactor for booster heater protection
Smart grid ready input
IN12 TBI.3 1-2 —
TH1 Thermistor (Room temp.)(Option)
INA1 TBI.4 1-3 CN1A Flow sensor
TH2 Thermistor (Ref. liquid temp.)
*1. Set the ON/OFF cycle time of the room thermostat for 10 minutes or more;
THW1 Thermistor (Flow water temp.)
otherwise the compressor may be damaged.
*2. If using outdoor thermostat for controlling operation of heaters, the lifetime of the heaters and THW2 Thermistor (Return water temp.)
related parts may be reduced. THW5B Thermistor (DHW tank water temp.)(Option)
input setting” screen in the service menu. THW6
THW7 Thermistor (Zone1 return temp.)(Option)
Table 2 Outputs
THW8
Name Terminal block Connector Item OFF ON
OUT1 TBO.1 1-2 CNP1 OFF ON THW10 Thermistor (Mixing tank temp.)(Option)
(Space heating/cooling & DHW)
Water circulation pump 2 output THWB1
(Space heating/cooling for Zone1) IN1 Room thermostat 1 (Local supply)
Water circulation pump 3 output IN2 Flow switch 1 (Local supply)
OUT3 TBO.1 5-6 — (Space heating/cooling for Zone2) *1 OFF ON IN3 Flow switch 2 (Local supply)
2-way valve 2b output *2
IN4 Demand control (Local supply)
TBO.2 4-6 CNV1 3-way valve (2-way valve) output
OUT4 Heating DHW IN5 Outdoor thermostat (Local supply)
— CN851 3-way valve output
TBO.2 1-2 Close IN6 Room thermostat 2 (Local supply)
TBO.2 2-3 Open IN7 Flow switch 3 (Local supply)
OUT6 — CNBH 1-3 Booster heater 1 output OFF ON IN8 Electric energy meter 1 (Local supply)
OUT8 TBO.4 7-8 — Cooling signal output OFF ON IN10 Heat meter (Local supply)
IN11
OUT10 TBO.3 1-2 — Boiler output OFF ON Smart grid ready input (Local supply)
IN12
OUT11 TBO.3 5-6 — Error output Normal Error
OUT12 TBO.3 7-8 — Defrost output Normal Defrost INA1 Flow sensor
OUT13 TBO.4 3-4 — 2-way valve 2a output *2 OFF ON FLOW TEMP. CONTROLLER (FTC)
Water circulation pump 4 output TBO.1−4 Terminal block <Outputs>
(DHW) TBI.1−6 Terminal block <Signal Inputs, Thermistor>
OUT15 TBO.4 1-2 — Comp. ON signal OFF ON F1 Fuse (IEC T10AL250V)
OUT16 TBO.3 3-4 — Thermo ON signal OFF ON F2 Fuse (IEC T6.3AL250V)
OUTA1 TBI.4 7-8 — Analog output 0V-10V
SW1−6 DIP switch *See Table 6.6.1
Do not connect to the terminals that are indicated as “—” in the “T X1−16 Relay
*1. For 2-zone temperature control.
*2. For 2-zone valve ON/OFF control. LED1 Power supply (FTC)
OCH712C 12
6-3. EHSD-VM6D.UK, ERSD-VM6D.UK, EHSC-VM6D.UK, ERSC-VM6D.UK, EHPX-VM6D.UK, ERPX-VM6D.UK
CNPWM CN01
1 1 via outdoor unit by independent source
<How to use TBO.1 to 4>
Power supply 3
F1 Connect them using either way as shown below. To outdoor Power supply To outdoor
to Booster heater 3 3 5 unit ~/N 230V 50Hz unit
~/N 230V 50Hz F2 Tool
CNP1 Tool
(WH) TBO.1
L N 1 X1
1
BREAKER
(1) (3) M
CIRCUIT
1~ 2
M 3
1~ MP1 X2
ECB1 MP2 Outline view Top view
X3
M 5
GNYE
GNYE
1~
RD
OG
RD
OG
BU
BU
YE
YE
6
2 4 MP3
1 X14 FTC board
M
OG
YE
1~
RD
BU
OG
1
YE
MP4 3 1 TBO.1 CN01
CNP4 (BK) 3
(RD) 2
1 3 5 A1 5
3 1
BHCP X5A CNP1
TBO.2 4 (WH) CN01 1 CN01 1
1 3 F2 F1 (BK) 3 (BK) 3
M N 5 5
1~ Open 2 6
X5B 1 1
2 4 6 A2 MXV 3 1 CN3C
CNP4
1 TBO.2 (BU) 3
4 3 (RD)
RD 2
LED1
BN BN
M 5
1~ 3
SW5 1 CN3C 1 CN3C 1
RD
BU
BU CNPWM (BU) 3 OG (BU) 3 OG

3WV 6 X4
4 (WH) 3
CNV1
(WH) 5 8
4 5 6
BHC1 1 6 1 1
TBO.2 1
1 3 5 A1 1 3 5 A1 BHC2 3 CNV1
GY
GY
M 3 CN851
1 TBO.3 (WH)
1~ 5 5 SW4 (BK)
2
2WV1
TBO.3 3
8
X10 4 6
Signal output 1
5 1
(Boiler) 1
PK
2
2 4 6 A2 2 4 6 A2 Signal output 3
(WH) (Option)
7 SW3
PK
8
VT
VT
X11
Signal output 5
(Error) 1 TBO.4 1
X12 2
WH/No.1
WH/No.2
Signal output
BU/No.3
BU/No.4
3 5
(Defrost) 8 4
TBO.4 5 SW2 1
X15
(Comp. on) 7 (BU)
2 5
X13 8 8
BH1 BH2 M 3 1 CNIH 1
1~ 4 (OG) CN22 1
3 1 (BU) 2
2 2 2 2WV2a X9
5
1 1 CNBHT SW1 SW6
6 CNBC CN108
BHF BHT X8 (GY) (BK)
3 3
Signal output 7 5
(Cooling) LED4
8 8
1
WH
WH
CNBHT 3
(BK) CNBH
1 5 (WH)
7
2 2 1 3
TAB1
CNBHT CNBC
3 (BK) (GY)
1
2 1
CNBC 3
3 (GY) CNBH
(WH) CN401 CN1A CNW5 CNW12 CN21 CN20
X6 (WH) (WH) (BU) (RD) (YE) (RD)
1 1
2 1 1 1 1 1 1
3 3
X7 3 2
CNBH 5 4 4 4 4
2 5 (WH)
7
7 87654321 87654321 87654321 87654321 87654321 87654321

8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1
1 4 1 4 1 4 1 3 1 2
- + - + - + + - CN1A
(WH)
CN22
(BU)
1 4 2 1
Main remote
V
controller
Sensor *
Pressre
Sensor
Flow
t° t° t° t° t° t° t° t° t° t° t°


Symbol Name
Name Terminal block Connector Item OFF (Open) ON (Short) TB1 Terminal block <Power supply, Outdoor unit>
Refer to SW2-1 in
IN2 TBI.1 5-6 — Flow switch 1 input MP2 Water circulation pump 2
IN3 TBI.1 3-4 — Flow switch 2 input (Zone1) MP3 Water circulation pump 3
IN4 TBI.1 1-2 — Demand control input Normal MP4 Water circulation pump 4 (DHW)(Local supply)
Boiler operation *3
tion Boiler operation *3 2WV2a 2-way valve (For Zone 1)(Local supply)
Refer to SW3-1 in 2WV2b 2-way valve (For Zone 2)(Local supply)
IN6 TBI.2 5-6 — Room thermostat 2 input *1
MXV Mixing valve (Local supply)
Refer to SW3-2 in
IN7 TBI.2 3-4 — Flow switch 3 input (Zone2) BHT Thermostat for booster heater
IN11 TBI.3 3-4 — BHC1 Contactor for booster heater 1
Smart grid ready input
IN12 TBI.3 1-2 — BHC2 Contactor for booster heater 2
INA1 TBI.4 1-3 CN1A Flow sensor
BHCP Contactor for booster heater protection
*1. Set the ON/OFF cycle time of the room thermostat for 10 minutes or more; TH1 Thermistor (Room temp.)(Option)
otherwise the compressor may be damaged.
related parts may be reduced. THW1 Thermistor (Flow water temp.)
THW5B Thermistor (DHW tank water temp.)(Option)
Table 2 Outputs
THW6
Name Terminal block Connector Item OFF ON
OUT1 TBO.1 1-2 CNP1 OFF ON THW8
(Space heating/cooling for Zone1) THW10 Thermistor (Mixing tank temp.)(Option)
Water circulation pump 3 output THWB1
OUT3 TBO.1 5-6 — (Space heating/cooling for Zone2) *1 OFF ON IN1 Room thermostat 1 (Local supply)
2-way valve 2b output *2
IN2 Flow switch 1 (Local supply)
OUT4 Heating DHW IN3 Flow switch 2 (Local supply)
TBO.2 1-2 Close IN4 Demand control (Local supply)
TBO.2 2-3 Open IN5 Outdoor thermostat (Local supply)
OUT7 — CNBH 5-7 Booster heater 2 output OFF ON IN7 Flow switch 3 (Local supply)
OUT8 TBO.4 7-8 — Cooling signal output OFF ON IN8 Electric energy meter 1 (Local supply)
IN9 Electric energy meter 2 (Local supply)
OUT10 TBO.3 1-2 — Boiler output OFF ON
IN10 Heat meter (Local supply)
OUT11 TBO.3 5-6 — Error output Normal Error
Smart grid ready input (Local supply)
OUT13 TBO.4 3-4 — 2-way valve 2a output *2 OFF ON IN12
Water circulation pump 4 output INA1 Flow sensor
(DHW) FLOW TEMP. CONTROLLER (FTC)
OUT15 TBO.4 1-2 — Comp. ON signal OFF ON TBO.1−4 Terminal block <Outputs>
OUT16 TBO.3 3-4 — Thermo ON signal OFF ON TBI.1−6 Terminal block <Signal Inputs, Thermistor>
OUTA1 TBI.4 7-8 — Analog output 0V-10V
Do not connect to the terminals that are indicated as “—” in the “T F2 Fuse (IEC T6.3AL250V)
*2. For 2-zone valve ON/OFF control. SW1−6 DIP switch *See Table 6.6.1
X1−16 Relay
OCH712C 13
6-4. EHSD-YM9D.UK, EHSD-YM9ED.UK, ERSD-YM9D.UK, EHSC-YM9D.UK, EHSC-YM9ED.UK, ERSC-YM9D.UK,
EHSE-YM9ED.UK, ERSE-YM9ED.UK, EHPX-YM9D.UK, EHPX-YM9ED.UK, ERPX-YM9D.UK
CNPWM CN01
Power supply 1 via outdoor unit by independent source
to Booster heater
1 <How to use TBO.1 to 4>
3~ 400V 50Hz F1 To outdoor Power supply To outdoor
L1 L2 L3 F2 Tool
(1) (3) (5) CNP1 Tool
(WH) TBO.1
1 X1
1
BREAKER
M
CIRCUIT
1~ 2
M 3
1~ MP1 X2
ECB1 M 3 Conductor Conductor
2 4 6 MP2 X3 Outline view Top view
M 5
GNYE
GNYE
RD
WH
BK
1~
RD
OG
RD
OG
BU
BU
YE
YE
6
BHCP 1 3 5 A1 MP3
1 X14 FTC board
M
OG
YE
1~
OG
1
YE
MP4 3 1 TBO.1 CN01
2 4 6 A2 CNP4
2 (BK) 3
(RD)
3 5
1 CNP1
X5A
TBO.2 4 (WH) CN01 1 CN01 1
1 3 F2 F1 (BK) 3 (BK) 3
M N 5 5
2
WH
WH
1~ Open 6
RD
RD
BK
BK
BHC1 BHC2 X5B 1 1

MXV 3 1 CN3C
1 3 5 A1 1 3 5 A1 CNP4
1 TBO.2 (BU) 3
4 3 (RD) LED1
M 2 BN BN
1~ 5 SW5 1 CN3C 1 CN3C 1
3 CNPWM OG OG
3WV 6 X4 (BU) 3 (BU) 3
4 (WH) 3
CNV1 5
2 4 6 A2 2 4 6 A2 (WH) 8
4 5 6 1 6 1 1
GY
GY
PK
PK
1
VT
VT
TBO.2 3 CNV1
M 3 CN851
1 TBO.3 (WH)
1~ 5 5 SW4 (BK)
2
2WV1
TBO.3 3
8
WH/No.1
WH/No.2
WH/No.3
BU/No.4
BU/No.5
BU/No.6
X10 4 6
Signal output 1
5 1
(Boiler) 2 1
Signal output 3
7 SW3
(WH) (Option)
2 2 2 (thermo on) 4 LED2 5
8
X11
Signal output 5
(Error) 1 TBO.4 1
X12 2
Signal output 3 5
(Defrost) 8 4
TBO.4 5 SW2 1
X15
(Comp. on) 7 (BU)
2 5
X13 8 8
M 3 1 CNIH 1
1~ 4 (OG) CN22 1
3 1 (BU) 2
BH1 BH2 2WV2a X9
5
1 1 CNBHT SW1 SW6
θ 6 CNBC CN108
X8 (GY) (BK)
BHF BHT 3 3
Signal output 7 5
(Cooling) LED4
8 8
1
WH
WH
CNBHT 3
(BK) CNBH
1 5 (WH)
7
3
TAB1
2 CNBC
1 (GY)
2 CNBHT
1
3 (BK)
3
2 1
CNBC CNBH
(GY) (WH) CN401 CN1A CNW5 CNW12 CN21 CN20
3 X6 (WH) (WH) (BU) (RD) (YE) (RD)
1
1 1 1 1 1 1
1
2 3
X7 3 2
3 5 4 4 4 4
CNBH
2 5 (WH) 7
87654321 87654321 87654321 87654321 87654321 87654321
7 TBI.1 TBI.2 TBI.3 TBI.4 TBI.5 TBI.6

8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1
1 4 1 4 1 4 1 3 1 2
- + - + - + + - CN1A
(WH)
CN22
(BU)
1 4 2 1
Main remote
V
controller
Sensor *
Pressre
Sensor
Flow
t° t° t° t° t° t° t° t° t° t° t°


Name Terminal block Connector Item OFF (Open) ON (Short) Symbol Name
Refer to SW2-1 in TB1 Terminal block <Power supply, Outdoor unit>
<Table 6.6.1 DIP Switch Functions>. ECB1 Earth leakage circuit breaker for booster heater
MP2 Water circulation pump 2
MP3 Water circulation pump 3
Boiler operation *3
MP4 Water circulation pump 4 (DHW)(Local supply)
Standard opera- Heater operation/
IN5 TBI.2 7-8 — Outdoor thermostat input *2 3WV(2WV1) 3-way valve (2-way valve 1)(Local supply)
tion Boiler operation *3
Refer to SW3-1 in 2WV2a 2-way valve (For Zone 1)(Local supply)
<Table 6.6.1 DIP Switch Functions>. 2WV2b 2-way valve (For Zone 2)(Local supply)
<Table 6.6.1 DIP Switch Functions>. BHT Thermostat for booster heater
IN8 TBI.3 7-8 — Electric energy meter 1
BHF Thermal fuse for booster heater
IN9 TBI.3 5-6 — Electric energy meter 2
Refer to installation manual. BH2 Booster heater 2
IN11 TBI.3 3-4 —
Smart grid ready input BHC1 Contactor for booster heater 1
IN12 TBI.3 1-2 —
INA1 TBI.4 1-3 CN1A Flow sensor BHC2 Contactor for booster heater 2
*1. Set the ON/OFF cycle time of the room thermostat for 10 minutes or more; BHCP Contactor for booster heater protection
otherwise the compressor may be damaged. TH1 Thermistor (Room temp.)(Option)
related parts may be reduced.
*3. To turn on the boiler operation, use the main remote controller to select “Boiler” in “External THW1 Thermistor (Flow water temp.)
Table 2 Outputs THW5B Thermistor (DHW tank water temp.)(Option)
OUT1 TBO.1 1-2 CNP1 OFF ON
(Space heating/cooling & DHW) THW8
OUT2 TBO.1 3-4 — OFF ON THW9 Thermistor (Zone2 return temp.)(Option)
(Space heating/cooling for Zone1)
Water circulation pump 3 output THW10 Thermistor (Mixing tank temp.)(Option)
OUT3 TBO.1 5-6 — (Space heating/cooling for Zone2) *1 OFF ON THWB1
2-way valve 2b output *2 IN1 Room thermostat 1 (Local supply)
TBO.2 4-6 CNV1 3-way valve (2-way valve) output IN2 Flow switch 1 (Local supply)
OUT4 Heating DHW
— CN851 3-way valve output IN3 Flow switch 2 (Local supply)
TBO.2 1-2 Close
OUT5 — Mixing valve output *1 Stop IN4 Demand control (Local supply)
TBO.2 2-3 Open
IN5 Outdoor thermostat (Local supply)
OUT6 — CNBH 1-3 Booster heater 1 output OFF ON
OUT8 TBO.4 7-8 — Cooling signal output OFF ON IN7 Flow switch 3 (Local supply)
OUT9 TBO.4 5-6 CNIH Immersion heater output OFF ON IN8 Electric energy meter 1 (Local supply)
OUT10 TBO.3 1-2 — Boiler output OFF ON IN9 Electric energy meter 2 (Local supply)
OUT11 TBO.3 5-6 — Error output Normal Error IN10 Heat meter (Local supply)
OUT13 TBO.4 3-4 — 2-way valve 2a output *2 OFF ON Smart grid ready input (Local supply)
IN12
OUT14 — CNP4 OFF ON INA1 Flow sensor
(DHW)
OUT15 TBO.4 1-2 — Comp. ON signal OFF ON FLOW TEMP. CONTROLLER (FTC)
OUT16 TBO.3 3-4 — Thermo ON signal OFF ON Terminal block <Outputs>
OUTA1 TBI.4 7-8 — Analog output 0V-10V Terminal block <Signal Inputs, Thermistor>
*1. For 2-zone temperature control. F2 Fuse (IEC T6.3AL250V)
*2. For 2-zone valve ON/OFF control.
SW1 6 DIP switch *See Table 6.6.1
X1 16 Relay
OCH712C 14
6-5. EHSD-TM9D.UK, EHSC-TM9D.UK
CNPWM CN01
Power supply 1 via outdoor unit by independent source
to Booster heater
1 <How to use TBO.1 to 4>
3~ 230V 50Hz F1 To outdoor Power supply To outdoor
L1 L2 L3 F2 Tool
(1) (3) (5) CNP1 Tool
(WH) TBO.1
1 X1
1
BREAKER
M
CIRCUIT
1~ 2
M 3
1~ MP1 X2
ECB1 M 3 Conductor Conductor
2 4 6 MP2 X3 Outline view Top view
M 5
GNYE
GNYE
RD
WH
BK
1~
RD
OG
RD
OG
BU
BU
YE
YE
6
BHCP 1 3 5 A1 MP3
1 X14 FTC board
M
OG
YE
1~
OG
1
YE
MP4 3 1 TBO.1 CN01
2 4 6 A2 CNP4
2 (BK) 3
(RD)
3 5
1 CNP1
X5A
TBO.2 4 (WH) CN01 1 CN01 1
1 3 F2 F1 (BK) 3 (BK) 3
Close 5
M N 5 5
2
WH
WH
1~ Open 6
RD
RD
BK
BK
BHC1 BHC2 X5B 1 1

MXV 3 1 CN3C
1 3 5 A1 1 3 5 A1 CNP4
1 TBO.2 (BU) 3
4 3 (RD) LED1
M 2 BN BN
1~ 5 SW5 1 CN3C 1 CN3C 1
3 CNPWM OG OG
3WV 6 X4 (BU) 3 (BU) 3
4 (WH) 3
CNV1 5
2 4 6 A2 2 4 6 A2 (WH) 8
4 5 6
6 1 1
GY
GY
PK
PK
1 1
VT
VT
TBO.2 CNV1
M 3 3 CN851
1 TBO.3 (WH)
1~ 5 SW4 (BK)
5 2
2WV1
TBO.3 3 1. Symbols used in wiring diagram are,
8
: connector, : terminal block.
WH/No.1
WH/No.2
WH/No.3
BU/No.4
BU/No.5
BU/No.6
X10 4 6
Signal output 1
1
(Boiler) 2
5
1 2. Indoor unit and outdoor unit connecting
Signal output 3
7 SW3
(WH) (Option) wires have polarities, make sure to match
2 2 2 (thermo on) LED2 5
4
X11
8 terminal numbers (S1, S2, S3) for correct
Signal output 5
(Error) 6
1 TBO.4 1
WiFi adapter
wirings.
8 CN105
Signal output 7
X12 2
3
1 LED3 (RD) (Option) 3. Since the outdoor unit side electric wiring
5
(Defrost) 8 4 may change, be sure to check the outdoor
TBO.4
X15
5 SW2
CNIT
1 unit electric wiring diagram for service.
Signal output 1 6
(Comp. on) 7 (BU)
2 5
X13 8 8
M 3 1 CNIH 1
1~ 4 (OG) CN22 1
3 1 (BU) 2
BH1 BH2 2WV2a X9
5
1 1 CNBHT SW1 SW6
θ 6 CNBC CN108
X8 (GY) (BK)
BHF BHT 3 3
Signal output 7 5
(Cooling) 8 LED4
1 8
WH
WH
CNBHT 3
(BK) CNBH
1 5 (WH)
7
3
TAB1
2 CNBC
1 (GY)
2 CNBHT
1
3 (BK)
3
2 1
CNBC CNBH
(GY) (WH) CN401 CN1A CNW5 CNW12 CN21 CN20
3 X6 (WH) (WH) (BU) (RD) (YE) (RD)
1
1 1 1 1 1 1
1
2 3
X7 3 2
3 5 4 4 4 4
CNBH
2 5 (WH) 7
87654321 87654321 87654321 87654321 87654321 87654321
7 TBI.1 TBI.2 TBI.3 TBI.4 TBI.5 TBI.6

8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1
1 4 1 4 1 4 1 3 1 2
- + - + - + + - CN1A
(WH)
CN22
(BU)
1 4 2 1
Main remote
Pressure
controller
Sensor
Sensor
Flow
t° t° t° t° t° t° t° t° t° t° t°


Name Terminal block Connector Item OFF (Open) ON (Short) Symbol Name
Room thermostat Refer to SW2-1 in TB1 Terminal block <Power supply, Outdoor unit>
IN1 TBI.1 7-8 —
1 input *1 <Table 6.6.1 DIP Switch Functions>. ECB1 Earth leakage circuit breaker for booster heater
Flow switch 1 Refer to SW2-2 in MP1 Water circulation pump 1(Space heating & DHW)
IN2 TBI.1 5-6 —
input <Table 6.6.1 DIP Switch Functions>. MP2 Water circulation pump 2
Flow switch 2 Refer to SW3-2 in (Space heating for Zone1)(Local supply)
IN3 TBI.1 3-4 —
input (Zone1) <Table 6.6.1 DIP Switch Functions>. MP3 Water circulation pump 3
Demand control Heat source OFF/ (Space heating for Zone2)(Local supply)
IN4 TBI.1 1-2 — Normal
input Boiler operation *3 MP4 Water circulation pump 4 (DHW)(Local supply)
Outdoor thermo- Standard opera- Heater operation/
IN5 TBI.2 7-8 — 3WV(2WV1) 3-way valve (2-way valve 1)(Local supply)
stat input *2 tion Boiler operation *3
Room thermostat Refer to SW3-1 in 2WV2a 2-way valve (For Zone 1)(Local supply)
IN6 TBI.2 5-6 — 2WV2b 2-way valve (For Zone 2)(Local supply)
2 input *1 <Table 6.6.1 DIP Switch Functions>.
Flow switch 3 Refer to SW3-2 in MXV Mixing valve (Local supply)
IN7 TBI.2 3-4 —
input (Zone2) <Table 6.6.1 DIP Switch Functions>. BHT Thermostat for booster heater
Electric energy BHF Thermal fuse for booster heater
IN8 TBI.3 7-8 —
meter 1
BH1 Booster heater 1
Electric energy
IN9 TBI.3 5-6 — BH2 Booster heater 2
meter 2
Refer to installation manual. BHC1 Contactor for booster heater 1
IN10 TBI.2 1-2 — Heat meter
IN11 TBI.3 3-4 — Smart grid ready BHC2 Contactor for booster heater 2
IN12 TBI.3 1-2 — input BHCP Contactor for booster heater protection
INA1 TBI.4 1-3 CN1A Flow sensor TH1 Thermistor (Room temp.)(Option)
*1. Set the ON/OFF cycle time of the room thermostat for 10 minutes or more; TH2 Thermistor (Ref. liquid temp.)
otherwise the compressor may be damaged. THW1 Thermistor (Flow water temp.)
*2. If using outdoor thermostat for controlling operation of heaters, the lifetime of the
heaters and related parts may be reduced. THW2 Thermistor (Return water temp.)
*3. To turn on the boiler operation, use the main remote controller to select “Boiler” in THW5B Thermistor (DHW tank water temp.)(Option)
“External input setting” screen in the service menu.
THW6
Table 2 Outputs
OUT1 TBO.1 1-2 CNP1 OFF ON THW9 Thermistor (Zone2 return temp.)(Option)
Water circulation pump 2 output THW10 Thermistor (Mixing tank temp.)(Option)
OUT2 TBO.1 3-4 — OFF ON THWB1
(Space heating/cooling for Zone1)
Water circulation pump 3 output IN1 Room thermostat 1 (Local supply)
OUT3 TBO.1 5-6 — (Space heating/cooling for Zone2) *1 OFF ON IN2 Flow switch 1 (Local supply)
2-way valve 2b output *2 IN3 Flow switch 2 (Local supply)
OUT4 Heating DHW IN4 Demand control (Local supply)
IN5 Outdoor thermostat (Local supply)
TBO.2 1-2 Close
OUT5 — Mixing valve output *1 Stop IN6 Room thermostat 2 (Local supply)
TBO.2 2-3 Open
OUT6 — CNBH 1-3 Booster heater 1 output OFF ON IN7 Flow switch 3 (Local supply)
OUT8 TBO.4 7-8 — Cooling signal output OFF ON IN9 Electric energy meter 2 (Local supply)
OUT9 TBO.4 5-6 CNIH Immersion heater output OFF ON IN10 Heat meter (Local supply)
OUT10 TBO.3 1-2 — Boiler output OFF ON IN11
OUT11 TBO.3 5-6 — Error output Normal Error Smart grid ready input (Local supply)
IN12
OUT12 TBO.3 7-8 — Defrost output Normal Defrost
INA1 Flow sensor
OUT13 TBO.4 3-4 — 2-way valve 2a output *2 OFF ON
Water circulation pump 4 output FLOW TEMP. CONTROLLER (FTC)
(DHW) TBO.1−4 Terminal block <Outputs>
OUT15 TBO.4 1-2 — Comp. ON signal OFF ON TBI.1−6 Terminal block <Signal Inputs, Thermistor>
OUT16 TBO.3 3-4 — Thermo ON signal OFF ON F1 Fuse (IEC T10AL250V)
OUTA1 TBI.4 7-8 — Analog output 0V-10V F2 Fuse (IEC T6.3AL250V)
Do not connect to the terminals that are indicated as “—” in the “T SW1−6 DIP switch *See Table 6.6.1
*2. For 2-zone valve ON/OFF control. X1−16 Relay
OCH712C 15
6-6. DIP Switch Functions
SW5
The DIP switch number is printed on the circuit board next to the relevant switch-
es. The word ON is printed on the circuit board and on the DIP switch block itself.
To move the switch you need to use a pin or the corner of a thin metal ruler or SW4
similar.
SW3
DIP switch settings are listed below in Table 6.6.1.
Only an authorised installer can change DIP switch setting under one’s own re-
sponsibility according to the installation condition. SW2
Make sure to turn off both indoor unit and outdoor unit power supplies before
SW1
changing the switch settings.
SW6
<Figure 6.6.1>
Default settings:
DIP switch Function OFF ON
Indoor model name
SW1 SW1-1 Boiler WITHOUT Boiler WITH Boiler OFF
SW1-2 Heat pump maximum outlet water temperature 55ºC 60ºC ON *1
SW1-3 DHW tank WITHOUT DHW tank WITH DHW tank OFF
SW1-4 Immersion heater WITHOUT Immersion heater WITH Immersion heater OFF
OFF: E***-M*D
SW1-5 Booster heater WITHOUT Booster heater WITH Booster heater
ON : E***-*M2/6/9*D
OFF: E***-M*D
SW1-6 Booster heater function For heating only For heating and DHW
ON : E***-*M2/6/9*D
OFF: Except E*PX-*M**D
SW1-7 Outdoor unit type Split type Packaged type
ON : E*PX-*M**D
SW1-8 Wireless remote controller WITHOUT Wireless remote controller WITH Wireless remote controller OFF
SW2 SW2-1 Room thermostat1 input (IN1) logic change Zone1 operation stop at thermostat short Zone1 operation stop at thermostat open OFF
SW2-2 Flow switch1 input (IN2) logic change Failure detection at short Failure detection at open OFF
OFF: E
xcept E***-VM2*D
SW2-3 Booster heater capacity restriction Inactive Active
ON : E***-VM2*D
OFF: Except ER**-*M**D
SW2-4 Cooling mode function Inactive Active
ON : ER**-*M**D
Automatic switch to backup heat source operation
SW2-5 Inactive Active *2 OFF
(When outdoor unit stops by error)
SW2-6 Mixing tank WITHOUT Mixing tank WITH Mixing tank OFF
SW2-7 2-zone temperature control Inactive Active *3 OFF
SW2-8 Flow sensor WITHOUT Flow sensor WITH Flow sensor ON
SW3 SW3-1 Room thermostat 2 input logic change Zone2 operation stop at thermostat short Zone2 operation stop at thermostat open OFF
SW3-2 Flow switch 2 and 3 input logic change Failure detection at short Failure detection at open OFF
SW3-3 — — — OFF
SW3-4 Electric energy meter WITHOUT Electric energy meter WITH Electric energy meter OFF
SW3-5 Heating mode function *4 Inactive Active ON
SW3-6 2-zone valve ON/OFF control Inactive Active OFF
SW3-7 Heat exchanger for DHW Coil in tank External plate HEX OFF
SW3-8 Heat meter WITHOUT Heat meter WITH Heat meter OFF
SW4 SW4-1 Multiple outdoor units control Inactive Active OFF
SW4-2 Position of multiple outdoor units control *5 Sub Main OFF
SW4-3 — — — OFF
SW4-4 Indoor unit only operation (during installation work) *6 Inactive Active OFF
SW4-5 Emergency mode (Heater only operation) Normal Emergency mode (Heater only operation) OFF *7
SW4-6 Emergency mode (Boiler operation) Normal Emergency mode (Boiler operation) OFF *7
SW5 SW5-1 DHW tank water temperature over heat protection (L4) Active Inactive *8 OFF
SW5-2 Advanced auto adaptation Inactive Active ON
SW5-3 Capacity code
SW5-4 SW5-3 SW5-4 SW5-5 SW5-6 SW5-7
E*SC-*M**D ON ON ON ON OFF
SW5-5 E*SD-*M**D ON OFF OFF ON OFF
SW5-6 E*SE-*M*ED OFF ON ON OFF ON
SW5-7 E*PX-*M**D OFF OFF OFF OFF OFF
SW5-8 — — — OFF
SW6 SW6-1 — — — OFF
SW6-2 — — — OFF
OFF: E
xcept E*SD-*M**D
SW6-3 Pressure sensor Inactive Active
ON : E*SD-*M**D
SW6-4 Analog output signal (0 to 10V) Inactive Active OFF
SW6-5 — — — OFF
<Table 6.6.1>
Notes: *1. W hen the hydrobox is connected with a PUMY-P outdoor unit of which maximum outlet water temperature is 55ºC, DIP SW1-2 must be changed to OFF.
*2. OUT11 will be available. For safety reasons, this function is not available for certain errors. (In that case, system operation must be stopped
and only the water circulation pump keeps running.)
*3. Active only when SW3-6 is set to OFF.
*4. This switch functions only when the hydrobox is connected with a PUHZ-FRP outdoor unit. When another type of outdoor unit is connected,
the heating mode function is active regardless of the fact that this switch is ON or OFF.
*5. Active only when SW4-1 is set to ON.
*6. Space heating and DHW can be operated only in indoor unit, like an electric heater. (Refer to "Indoor unit only operation” in page 42. )
*7. If emergency mode is no longer required, return the switch to OFF position.
*8. Please make sure to have necessary overheat protection on locally supplied solar thermal system side to secure safety, as the tank tem-
perature could be much higher (than current).
OCH712C 16
7 FIELD WIRING
Option1: Hydrobox powered via outdoor unit

<1 phase>
Affix label A that is included with the manuals near each wiring diagram for hydrobox and outdoor units.
Hydrobox
TB1
L
Outdoor unit
N
Earth Wiring To control

leakage circuit board
Power supply L S1 S1
circuit breaker or
~/N 230 V 50 Hz breaker Isolating
switch N S2 S2
*1, *2
S3 S3
ECB1
Wiring
circuit For
Power supply breaker or
L booster
~/N 230 V 50 Hz Isolating N heater
switch (Primary circuit)
<Figure 7.1>
Electrical connections 1 phase
Description Power supply Capacity Breaker Wiring
2 kW 16 A *2 2.5 mm²
Booster heater (Primary circuit) ~/N 230 V 50 Hz
6 kW 32 A *2 6.0 mm²
<3 phase> Hydrobox
Affix label A that is included with the manuals near each wiring diagram for hydrobox and outdoor units. TB1
L
Outdoor unit
N
To control
board
L1 S1 S1
Earth Wiring
Power supply leakage circuit L2 S2 S2
3N~ 400 V 50 Hz circuit breaker or
breaker Isolating L3 S3 S3
*1, *2 switch
N
ECB1
Wiring L1
Power supply circuit For
breaker or L2 booster
3~ 400 V 50 Hz (E***-YM9*D) Isolating heater
3~ 230 V 50 Hz (EH**-TM9*D) switch L3 (Primary circuit)
<Figure 7.2>
3~ 400 V 50 Hz 9 kW 16 A *2 2.5 mm²
Booster heater (Primary circuit)
3~ 230 V 50 Hz 9 kW 32 A *2 6.0 mm²
Wiring No. Hydrobox - Outdoor unit *3 3 × 1.5 (polar)

× size (mm²) Hydrobox - Outdoor unit earth *3 1 × Min. 1.5
Hydrobox - Outdoor unit S1 - S2 *4 230 VAC
Circuit rating
Hydrobox - Outdoor unit S2 - S3 *4 24 VDC
*1. If the installed earth leakage circuit breaker does not have an over-current protection function, install a breaker with that function along the same power line.
*2. A breaker with at least 3.0 mm contact separation in each pole shall be provided. Use earth leakage breaker (NV).
The breaker shall be provided to ensure disconnection of all active phase conductors of the supply.
*3. Max. 45 m
If 2.5 mm² used, Max. 50 m
If 2.5 mm² used and S3 separated, Max. 80 m
*4. The values given in the table above are not always measured against the ground value.
Notes: 1. Wiring size must comply with the applicable local and national codes.
2. Indoor unit/outdoor unit connecting cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 60245 IEC 57)
Indoor unit power supply cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 60227 IEC 53)
3. Install an earth line longer than power cables.
4. Please keep enough output capacity of power supply for each heater. Insufficient power supply capacity might cause chattering.
OCH712C 17
Option2: Hydrobox powered by independent source
<1 phase>
Affix label B that is included with the manuals near each wiring diagram for hydrobox and outdoor units.
Hydrobox
TB1
Earth Wiring
leakage circuit
Power supply circuit L
~/N 230 V 50 Hz breaker or
breaker Isolating N
*1, *2 switch
Outdoor unit
Earth Wiring
leakage circuit S1
Power supply circuit breaker or
L S1
~/N 230 V 50 Hz breaker Isolating N S2 To control
switch
S2 board
*1, *2
S3 S3
ECB1
Wiring
circuit For
Power supply breaker or
L booster
~/N 230 V 50 Hz Isolating heater
N
switch
<Figure 7.3>
2 kW 16 A *2 2.5 mm²
Booster heater ~/N 230 V 50 Hz
6 kW 32 A *2 6.0 mm²
<3 phase>
Affix label B that is included with the manuals near each wiring diagram for hydrobox and outdoor units.
Hydrobox
TB1
Earth Wiring
leakage circuit
Power supply circuit breaker or L
~/N 230 V 50 Hz breaker Isolating
*1, *2 switch N
To control
Outdoor unit board
L1 S1 S1
Earth Wiring
Power supply leakage circuit L2 S2 S2
circuit breaker or
3N~ 400 V 50 Hz breaker L3 S3
Isolating S3
*1, *2 switch
N
ECB1
Wiring L1
Power supply circuit For
3~ 400 V 50 Hz (E***-YM9*D) breaker or L2 booster
Isolating heater
3~ 230 V 50 Hz (EH**-TM9*D) switch L3
<Figure 7.4>
3~ 400 V 50 Hz 9 kW 16 A *2 2.5 mm²
Booster heater (Primary circuit)
3~ 230 V 50 Hz 9 kW 32 A *2 6.0 mm²
Hydrobox power supply ~/N 230 V 50 Hz *1. If the installed earth leakage circuit breaker does not have an
Hydrobox input capacity over-current protection function, install a breaker with that func-
*2 16 A tion along the same power line.
Main switch (Breaker)
*2. A breaker with at least 3.0 mm contact separation in each pole
Hydrobox power supply 2 × Min. 1.5
shall be provided. Use earth leakage breaker (NV).
Wiring No. Hydrobox power supply earth 1 × Min. 1.5
The breaker shall be provided to ensure disconnection of all ac-
× size (mm²) Hydrobox - Outdoor unit *3 2 × Min. 0.3 tive phase conductors of the supply.
Hydrobox - Outdoor unit earth — *3. Max. 120 m
Hydrobox L - N *4 230 VAC *4. The values given in the table above are not always measured
Circuit
Hydrobox - Outdoor unit S1 - S2 *4 — against the ground value.
rating
Hydrobox - Outdoor unit S2 - S3 *4 24 VDC
Notes: 1. Wiring size must comply with the applicable local and national codes.
2. Indoor unit/outdoor unit connecting cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 60245 IEC 57)
Indoor unit power supply cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 60227 IEC 53)
3. Install an earth line longer than power cables.
4. Please keep enough output capacity of power supply for each heater. Insufficient power supply capacity might cause chattering.
OCH712C 18
8 WATER SYSTEM DIAGRAM
EHPX-*M*(E)D
Water flow
ERS*-*M*(E)D
EHS*-YM9ED
<E*PX> (Packaged model system)
ERPX-*M*D
EHS*-*M*D
EHS*-MED
ERS*-MED
ERPX-MD
No. Part name
Hydrobox Cold
DHW water 1 Control and electrical box
Note: 12 16 13
2 Main remote controller
Do not attach an 27 Plate heat exchanger
additional pressure 28 3 (Refrigerant - Water) - - -
relief valve to the 26
4 Water circulation pump 1
heating (cooling)
circuit on E*PX 9 25 5 Pump valve
model to keep fire 6 Air vent (manual) - - -
8
safety. 7
18
21 7 Drain cock (Primary circuit) -
17
8 Booster heater 1, 2 - - -
5 Pa 10 9 Flow sensor
4 14
10 Manometer
22 3
29 31 32 *2 31 11 Pressure relief valve (3 bar) - - -
12 Automatic air vent
29
Local 13 Expansion vessel *3 - - *4 -
24 system *1 14 Strainer valve
15 Drain pan - - - -
11 31 29 29 16 Pressure relief valve (5 bar) *3 - - *4 -
17 THW1
28 18 THW2
19 TH2 - - -
Water Drain 20 Pressure sensor - - - *5 *5 *5 *5 *5
supply THW5B
(Optional part
21 PAC-TH011TK2-E or - - - - - - - -
<Figure 8.1> PAC-TH011TKL2-E)
22 Outdoor unit - - - - - - - -
23 Drain pipe (Local supply) - - - - - - - -
24 3-way valve (Local supply) - - - - - - - -
DHW indirect unvented tank
Note 25 (Local supply) - - - - - - - -
• Be sure to follow your local regulations to perform system configuration of the DHW con- Cold water inlet pipe
26 (Local supply) - - - - - - - -
nections. DHW outlet pipe
27 (Local supply) - - - - - - - -
• DHW connections are not included in the hydrobox package. All required parts are to be
sourced locally. Back flow prevention device
28 (Local supply) - - - - - - - -
• To enable draining of the hydrobox an isolating valve should be positioned on both the inlet Isolating valve
29 (Local supply) - - - - - - - -
and outlet pipework.
Magnetic filter (Local
• Be sure to install a strainer on the inlet pipe work to the hydrobox. 30 supply) (Recommended) - - - - - - - -
• Suitable drain pipework should be attached to the relief valves instructed to be connected 31 Strainer (Local supply) - - - - - - - -
to it in Figure 8.1 and 8.2 in accordance with your country's regulations. 32 Air vent (Local supply) - - - - - - - -
• A backflow prevention device must be installed on water supply pipework (IEC 61770). <Table 8.1>
• When using components made from different metals or connecting pipes made of different
metals insulate the joints to prevent a corrosive reaction taking place which will damage the *1 Refer to the following section [Local system].
pipework. *2 If the outdoor unit is higher than the indoor unit, or if there is a
location where air gets trapped in the upper part of the water
pipe, consider adding this part.
*3 EHPX-YM9ED and EHPX-MED are not included.
*4 ERSE-YM9ED is not included.
*5 Only 2HP(E*SD) model.
<E*S*> (Split model system) Refrigerant flow

Water flow
<E*SE only>
Hydrobox Cold
DHW water
12 16 13 12
27 28
26
20
6
25
8 8
9 9 11
5 11 21
4 7 18
19 17
17
3 14 P 10
22 23
30
29
Drain
Local
24
system *1
29
Flare connections
28
Water Drain
supply
<Figure 8.2>
OCH712C 19
Local system
1-zone temperature control
Zone1 Zone1
3
4
1 1
2-zone temperature control 1-zone temperature control with boiler

11
Zone1
13 Zone1
5
4
11
3
1
Zone2 5
6 9
2 7
4
1
8
2
10
2-zone temperature control & Buffer tank control 1-zone temperature control
(2-zone valve ON/OFF control)
Zone1 Zone1
14
3
5
4 16
12 *1
1
1 Zone2
Zone2 15
6 9
2 7
8
10
10
1. Zone1 heat emitters (e.g. radiator, fan coil unit) (local supply) 10. Zone2 heat emitters (e.g. underfloor heating) (local supply)
2. Mixing tank (local supply) 11. Boiler flow water temp. thermistor (THWB1) Optional part:
3. Zone1 flow water temp. thermistor (THW6) 12. Mixing tank thermistor (THW10) *1 PAC-TH012HT(L)-E
Optional part: PAC-TH011-E
4. Zone1 return water temp. thermistor (THW7) 13. Boiler (local supply)
5. Zone1 water circulation pump (local supply) 14. Zone1 2-way valve (local supply)
6. Motorized mixing valve (local supply) 15. Zone2 2-way valve (local supply)
7. Zone2 flow water temp. thermistor (THW8) 16. Bypass valve (local supply)
Optional part: PAC-TH011-E
8. Zone2 return water temp. thermistor (THW9)
9. Zone2 water circulation pump (local supply) *1 ONLY Buffer tank control (heating/cooling) applies to "Smart grid ready".
OCH712C 20
Filling the System (Primary Circuit)
1. Check and charge expansion vessel.
2. Check all connections including factory fitted ones are tight.
3. Insulate pipe work between hydrobox and outdoor unit.
4. Thoroughly clean and flush, system of all debris. (Refer to 4.2 in the installation manual.)
5. Fill primary heating circuit with water and suitable anti-freeze and inhibitor as necessary. Always use a filling loop with double check valve when filling the
primary circuit to avoid back flow contamination of water supply.
• Anti-freeze should always be used for package systems. It is the responsibility of the installer to decide if anti-freeze solution should be used in split systems
depending on each site’s conditions. Corrosion inhibitor should be used in both split and package systems.
Figure below shows freezing temperature against anti-freeze concentration. This figure is an example for FERNOX ALPHI-11. For other anti-freeze, please refer
to relevant manual.
• When connecting metal pipes of different materials, insulate the joints to prevent a corrosive reaction taking place which will damage the pipework.
6. Check for leakages. If leakages are found, retighten the screws on the connections.
7. Pressurise system to 1 bar.
8. Release all trapped air using air vents during and following heating period.
9. Top up with water as necessary. (If pressure falls below 1 bar)
10. After removing the air, automatic air vent MUST be closed.
5
Freezing temperature [°C]
−5
−10
−15
−20
−25
0 10 20 30 40 50
Anti-freeze concentration [%]
Draining the Hydrobox

WARNING: DRAINED WATER MAY BE VERY HOT
1. Before attempting to drain the hydrobox, isolate from the electrical supply to prevent booster heater burning out.
2. Isolate hydrobox from primary water circuit and drain water from hydrobox. Use a suitable heat resistant hose to assist in these operations.
3. Drain any remaining water from booster heater using fitted drain cock and hose, and the drain valve on the primary circuit to safely drain the unit.
4. After the hydrobox is drained, water remains in the following component parts. Drain water completely by checking the inside of the parts.
• Strainer (Remove the strainer cover.)
• Pressure relief valve (Operate the valve.)
OCH712C 21
9 CONTROLS
9-1. Main remote controller <Main remote controller parts>
To change the settings of your heating/cooling system please use the main Letter Name Function
remote controller located on the front panel of the cylinder unit or hydrobox. A Screen Screen in which all information is displayed.
The following is a guide to viewing the main settings. Should you require more
B Menu Access to system settings for initial set up and
information please contact your installer or local Mitsubishi Electric dealer.
modifications.
Cooling mode is available for ERS series only. However, Cooling mode is not
C Back Return to previous menu.
available when the indoor unit is connected to PUHZ-FRP.
D Confirm Used to select or save. (Enter key)
E Power/Holiday If system is switched off pressing once will turn
system ON. Pressing again when system is
switched on will enable Holiday Mode. Holding the
button down for 3 secs will turn the system off. (*1)
F1-4 Function keys Used to scroll through menu and adjust settings.
A Function is determined by the menu screen visible
on screen A.
*1 When the system is switched off or the power supply is disconnect-

ed, the indoor unit protection functions (e.g. freeze stat. function) will
NOT operate. Please beware that without these safety functions the
enabled indoor unit may potentially become exposed to damage.
F1 F2 F3 F4
<Main screen icons>
Icon Description
E 1 Legionella When this icon is displayed, ‘Legionella prevention
prevention mode’ is active.
2 Heat pump ‘Heat pump’ is running.
Defrosting
B C D
Emergency heating
‘Quiet mode’ is activated.
12 15 14 11 1 17 2 3 16 3 Electric heater When this icon is displayed, the ‘Electric heaters’

(booster or immersion heater) are in use.
4 Target Target flow temperature
temperature Target room temperature
Compensation curve
5 OPTION Pressing the function button below, this icon will dis-
10 play the option screen.
6 + Increase set temperature.
13 7 - Decrease set temperature.
8 Z1 Z2 Pressing the function button below, this icon switches
between Zone1 and Zone2.
4 Information Pressing the function button below, this icon displays
9 the information screen.
9 Space heating Heating mode
(cooling) mode Zone1 or Zone2
Cooling mode
Zone1 or Zone2
8
10 DHW mode Normal or ECO mode
11 Holiday mode When this icon is displayed, ‘Holiday mode’ activated.
12 Timer
5 Prohibited
7 6
Server control
Main screen Stand-by
Stand-by (*2)
Stop
Operating
13 Current Current room temperature
temperature Current water temperature of DHW tank
14 The Menu button is locked or the switching of the
operation modes between DHW and Heating opera-
tions are disabled in the Option screen. (*3)
15 SD memory card (NOT for the user) is inserted.

16 Buffer tank When this icon is displayed, 'Buffer tank control' is
control active.
17 Smart grid ready When this icon is displayed, 'Smart grid ready' is
active.
*2 This unit is in Stand-by whilst other indoor unit(s) is in operation by
priority.
*3 To lock or unlock the Menu, press the BACK and CONFIRM keys
simultaneously for 3 seconds.
OCH712C 22
9-2. Setting the Main remote controller
After the power has been connected to the outdoor and hydrobox (See "7. FIELD WIRING"), the initial system settings can be entered via the main remote controller.
1. Check all breakers and other safety devices are correctly installed and turn on power to the system.
2. When the main remote controller is switched on for the first time, the screen automatically goes to Initial settings menu, Language setting screen and Date/Time
setting screen in order.
3. Main remote controller will automatically start up. Wait approximately 6 minutes whilst the control menus load.
4. When the controller is ready, a blank screen with a line running across the top will be displayed.
5. Press button E (Power) (refer to 9-1. Main remote controller) to turn on the system. Before turning on the system, perform initial settings as instructed below.
9-3. Main Settings Menu

The main settings menu can be accessed by pressing the MENU button. To re-
duce the risk of untrained end users altering the settings accidentally, there are
2 access levels to the main settings; and the service section menu is password
protected.
User Level – Short press

If the MENU button is pressed once for a short time, the main settings will be
displayed but without the edit function. This will enable the user to view current
settings but NOT change the parameters.
Installer Level – Long press

If the MENU button is pressed down for 3 seconds, the main settings will be dis-
played with all functionality available.
The colour of buttons is inverted as per right figure.
▼
▼
The following items can be viewed and/or edited (dependent on access level). Main menu
• Domestic Hot water (DHW)
• Heating/Cooling
• Schedule timer
Long Press
• Holiday mode
• Initial settings
• Service (Password protected)
General Operation
● To find the icon that you wish to set, use the F2 and F3 buttons to move between the icons.
● The highlighted icon will appear as a larger version of the centre of the screen.
● Press CONFIRM to select and edit the highlighted mode.
●F ollow the <Main remote controller Menu Tree> for further setting, using ◄► buttons for scrolling or F1 to F4
for selecting.
OCH712C 23
<Main Controller Menu Tree>
Unrestricted access
Initial Installer only
Main screen * Short press for 1 Zone system. Shaded items relate
to DHW functions.
F1 * Information These are only avail-
able if the system in-
F4 Option F1 Forced DHW ON ( )/OFF cludes a DHW tank.
F2 DHW ON ( )/Prohibited ( )/Timer ( )
Long press
F3 Heating/Cooling ON ( )/Prohibited ( )/Timer ( )
F4 Energy monitor Consumed electrical energy
Menu Delivered energy
F1
Main DHW Normal/Eco
menu F3
Menu
Legionella Active/Non active
Main
menu Hot Water (DHW) DHW max. temp.
F2 ( EDIT) DHW max. temp. drop
DHW
DHW max. operation time
DHW mode restriction
DHW recharge
Hot water temp.
Frequency
F4 ( EDIT)
Legionella Start time
Max. operation time
Duration of max. temp.
F1 (Zone1) Heating room temp.( ) / Heating flow temp.( ) / Heating compensation curve( ) / Cooling flow temp.
F2 (Zone2) Heating room temp.( ) / Heating flow temp.( ) / Heating compensation curve( ) / Cooling flow temp.
Heating/Cooling F3 (PREVIEW) Compensation curve preview

F1
Zone1 F2 F3 Curve parameters
Zone1/2 select
F4 ( EDIT) Compensation curve edit F4 Adjustment
Zone2 F2 F3 Curve parameters

F4 Adjustment
F4 Schedule2 period setting screen1 F2 F3 Term setting F4

save
( EDIT) F4 Schedule
timer preview Day
Time select
Zone1
F1
select Temp.setting save
Zone1/2 select F4 Schedule
Zone2 timer preview Day Time select
Schedule2 period Heating select Temp.setting save
preview screen F4 Schedule
timer preview Time select
Schedule timer Zone1 Day
F1
Zone1/2 select select Temp.setting save
Schedule1 F4 Schedule
timer preview Day Time select
Cooling Zone2
Schedule1/2 select
F4 Schedule timer preview
Day
select
Time select
DHW save
F4 Schedule Day Time select
timer preview select
F1 Zone1 Temp.setting save
Zone1/2 select
F4 Schedule
Zone2 timer preview Day Time select
Heating select
Temp.setting save
F4 Schedule
Time select
F1 Zone1 timer preview Day
Zone1/2 select select Temp.setting save
Schedule2 F4 Schedule
timer preview Time select
Cooling Zone2 Day
F4 Schedule timer preview
Day Time select
select
DHW save
DHW Active/Non active

Active/Non active Heating room temp.
Heating/ Zone1 Heating flow temp.
Cooling
Holiday F1 F2
Cooling flow temp.
Zone1/2 select
mode F3 Holiday mode setting Heating room temp.
( EDIT) Zone2 Heating flow temp.
Cooling flow temp.
Date/Time yyyy/mm/dd/hh:mm
Language EN/FR/DE/SV/ES/IT/DA/NL/FI/NO/PT/BG/PL/CZ/RU/TR/SL
Summer time OFF/ON
Temp. display OFF/Room/Tank/Room&Tank
Contact number
Initial Time display hh:mm/hh:mm AM/AM hh:mm Sensor setting TH1/Main RC/
settings Room RC1-8/ “Time/
°C/°F °C/°F Zone”
Zone1
Room RC zone select
Time setting
Select Time/Zone
Sensor setting
Room sensor settings
F1 F2
Sensor setting TH1/Main RC/
Zone1/2 select Room RC1-8/ “Time/
Sensor setting Zone”
Zone2
Time setting
Select Time/Zone
<Continued to next page.> Sensor setting
OCH712C 24
<Continued from the previous page.> Unrestricted access
<Main Controller Menu Tree> Installer only
Initial Shaded items relate
to DHW functions.
Main screen Main These are only avail-
menu Manual operation able if the system in-
Menu Function settings cludes a DHW tank.
Service
Password Thermistor adjustment
protected
Economy settings for pump ON/OFF Long press
Delay
Electric heater (Heating) ON/OFF
Delay
Auxiliary settings ON/OFF (Booster heater/Immersion heater)
Electric heater (DHW) Delay
Mixing valve control Running
Interval
Flow sensor Minimum

Maximum
Analog output Priority
Interval
Heat source setting Standard (Heat pump & electric heater)/Heater (Electric heater only)/
Boiler/Hybrid (Heat pump & heater/Boiler)
Pump speed
Heat pump flow rate range Minimum

Heat pump settings Maximum
Quiet mode
Min.temp.
Operation settings Heating Flow temp.range
operation Max.temp.
Mode
Room temp.control
Interval
ON/OFF
H/P thermo diff.adjust Lower limit
Upper limit
Flow t.
Freeze stat function
Ambient
ON/OFF
Simultaneous operation
Ambient
ON/OFF
Cold weather function
Ambient
Ambient
Hybrid
settings Priority Ambient/
Cost /CO2
Electricity
Energy
Boiler settings *1 price Boiler
Schedule
Electric
CO2
Intelligent emission Boiler
settings Heat pump capacity
Boiler efficiency
Heat source Booster heater 1
capacity
Booster heater 2
capacity
ON/OFF
DHW
Target temp.
ON/OFF
Heating
Smart grid ready Target temp.
ON/OFF
Cooling
Target temp.
ON/OFF(Heating)
Pump cycles ON/OFF(Cooling)
Interval
ON/OFF
Start & Finish
Target temp. Max. temp.
Floor dry up function Max. temp. period
Temp. increase step
Flow temp.
(Increase) Increase interval
Temp. decrease step
Flow temp. Decrease interval
(Decrease)
Summer mode ON/OFF
Ambient(Heating ON)
Ambient temp.
Summer mode Ambient(Heating OFF)
Time(Heating ON)
Judgement time
Time(Heating OFF)
Forced heating ON Ambient
Water flow control ON/OFF

*1 For more details, refer to the installation manual of PAC-TH012HT(L)-E.
OCH712C 25
<Continued from the previous page.> Unrestricted access
<Main Controller Menu Tree> Installer only
Initial Shaded items relate
to DHW functions.
Main screen Main These are only avail-
menu able if the system in-
Menu cludes a DHW tank.
Long press
Booster heater 1 capacity

Electric heater Booster heater 2 capacity
capacity Immersion heater
Analog output
Pump 1
Energy monitor Water pump input Pump 2
settings Pump 3
Service Delivered energy adjustment
Password
Electric energy meter Pump 4
protected
Heat meter
Demand control (IN4) OFF (Heat source)/Boiler
External input settings
Outdoor thermostat (IN5) Heater/Boiler
Thermo ON output Zone1/Zone2/Zone1&2
Commissioning wizard
Running information
Thermistor reading
Summary of settings
Error history
Password protection
Main controller Yes/No
Manual reset
FTC Yes/No
SD Main RC F1 F2 F3 Select download data
SD card
Main RC SD Select upload data
OCH712C 26
9-4. Service Menu
The service menu provides functions for use by installer or service engineer. It is NOT intended the home owner alters settings within this menu. It is for this reason
password protection is required to prevent unauthorised access to the service settings.
The factory default password is "0000".

Follow the procedure described in General Operation for the set up operation.
The service menu is navigated using the F1 and F2 buttons to scroll through the functions. The menu is split across 2 screens and is comprised of the following
functions;
1. Manual operation
2. Function settings
3. Thermistor adjustment
4. Auxiliary settings
5. Heat source setting
6. Pump speed
7. Operation settings
8. Energy monitor settings
9. External input settings
10. Running information
11. Thermistor reading
12. Summary of settings
13. Error history
14. Password protection
15. Manual reset
16. SD card
any functions cannot be set whilst the indoor unit is running. The installer should turn off the unit before trying to set these functions. If the installer attempts to
M
change the settings whilst the unit is running, the main remote controller will display a reminder message prompting the installer to stop operation before continu-
ing. By selecting “Yes”, the unit will cease operation.
<Manual operation>
During the filling of the system the water circulation pump and 3-way valve can
be manually overridden using manual operation mode.
When manual operation is selected a small timer icon appears in the screen.
The function selected will only remain in manual operation for a maximum of 2
hours. This is to prevent accidental permanent override of the FTC.
►Example
Pressing F3 button will switch manual operation mode ON for the main 3-way
valve. When filling of the DHW tank is complete the installer should access this
menu again and press F3 to deactivate manual operation of the part. Selected Running Error
indication
Alternatively after 2 hours manual operation mode will no longer be active and
FTC will resume control of the part.
Manual operation menu screen
Manual operation and heat source setting cannot be selected if the system
is running. A screen will be displayed asking the installer to stop the system
before these modes can be activated.
The system automatically stops 2 hours after the last operation.
<Function settings>
Function Setting allows the setting of auto recovery after power failure and of
smart grid ready.
1. From the service menu use F1 and F2 to highlight Function Setting.

2. Press CONFIRM.
3. Ensure the Ref address and unit number are displayed to the right.
4. Press CONFIRM.
5. Use F3 and F4 to highlight either 1/2/3 (see below).
6. Press CONFIRM.
Setting Unit Mode Number

Auto recovery after power failure Grp Mode1 1 - Inactive
2 - Active *1
3 - NO FUNCTION
*1 Approx. 4-minute delay after power is restored.
OCH712C 27
<Thermistor adjustment>
This function allows adjustments to be made to the thermistor readings from
−10 to 10°C in 0.5°C intervals.
THW1: Thermistor (Flow water temp.)

THW2: Thermistor (Return water temp.)
THW5B: Thermistor (DHW tank water temp.)(Option)
THW6: Thermistor (Zone1 flow temp.)(Option)
THW7: Thermistor (Zone1 return temp.)(Option)
THW8: Thermistor (Zone2 flow temp.)(Option)
THW9: Thermistor (Zone2 return temp.)(Option)
THW10: Thermistor (Mixing tank water temp.)
THWB1: Thermistor (Boiler flow temp.)(Option)
▼ ▲
<Auxiliary settings>
This function is used to set the parameters for any auxiliary parts used in the system
Menu subtitle Function/Description
Economy settings for Water pump stops automatically in certain period of time from
pump when operation is finished.
Delay Time before pump switched off *1
Electric heater To select “WITH booster heater (ON)” or “WITHOUT booster
(Heating) heater (OFF)” in Heating mode.
Delay The minimum time required for the booster heater to turn ON
from after Heating mode has started.
Electric heater (DHW) To select "WITH (ON)" or "WITHOUT (OFF)" booster heater or
immersion heater individually in DHW mode.
Delay The minimum time required for the booster heater or immersion Auxiliary settings menu screen
heater to turn ON from after DHW mode has started. (This
setting is applied for both booster and immersion heater.)
Mixing Running Period from valve fully open (at a hot water mixing ratio of 100%)
valve to valve fully closed (at a cold water mixing ratio of 100%)
control *2 Interval Interval (min.) to control the Mixing valve.
Flow Minimum The minimum flow rate to be detected at Flow sensor.
sensor *3 Maximum The maximum flow rate to be detected at Flow sensor.
*1 Decreasing "time before pump switched off" may increase the duration of stand-by in
Heating/Cooling mode.
*2 Set the Running time according to the specifications of the actuator of each mixing valve.
It is recommended to set the interval to 2 minutes that is a default value. With the interval
set longer, it could take longer to warm up a room.
*3 Do not change the setting since it is set according to the specification of Flow sensor
attached to the hydrobox.
Economy settings for pump

1. From the Auxiliary settings menu, highlight Economy Settings for water circulation pump.
2. Press CONFIRM.
3. The economy settings for water circulation pump screen is displayed.
4. Use button F1 to switch the economy settings ON/OFF.
5. Use buttons F3 and F4 to adjust the time the water circulation pump will run. (3 to 60
minutes)
Economy settings for pump screen
Electric heater (Heating)

1. From the Auxiliary settings menu, highlight Electric heater (Heating).
2. Press CONFIRM.
3. The Electric heater (Heating) screen is displayed.
4. Press F1 button to switch the function ON/OFF.
5. Use F3 and F4 buttons to adjust the time period of heat pump only operation
before the booster heater will assist in space heating. (5 to 180 minutes)
Electric heater (Heating) screen
Electric heater (DHW)

1. From the Auxiliary settings menu, highlight Electric heater (DHW).
2. Press CONFIRM.
3. The Electric heater (DHW) screen is displayed.
4. Press F1 button to switch the function ON/OFF.
5. Use F3 and F4 buttons to adjust the time period of heat pump only operation
before the booster heater and the immersion heater (if present) will assist in
DHW heating. (15 to 30 minutes)
Electric heater (DHW) screen
OCH712C 28
Mixing valve control
1. From the Auxiliary settings menu, highlight Mixing valve control.
2. Press CONFIRM.
3. The Mixing valve control screen is displayed.
4. Use F1 and F2 buttons to set Running time between 10 to 240 seconds. The Running time equals to
a period from full open of the valve (at a hot water mixing ratio of 100%) to full close (at a cold water
mixing ratio of 100%).
Note: Set the Running time according to the specifications of the actuator of each mixing valve.
1. From the Auxiliary settings menu, highlight Mixing valve control.

2. Press CONFIRM.
3. The Mixing valve control screen is displayed. Mixing valve control setting screen
4. Press F3 and F4 buttons to set the interval between 2-zone temperature controls of the mixing valve
between 1 to 30 minutes.
Note: It is recommended to set the interval to 2 minutes that is a default value. With the interval
set longer, it could take longer to warm up a room.
Flow sensor
1. From the Auxiliary settings menu, highlight Flow sensor.
2. Press CONFIRM.
3. Press F3 or F4 buttons to select a refrigerant address of which you wish to configure or check the
settings, and press CONFIRM. *1
4. The Flow sensor screen is displayed.
5. Use F1 and F2 buttons to set the minimum flow rate of flow sensor between 0 to maximum L/min.
6. Use F3 and F4 buttons to set the maximum flow rate of flow sensor between minimum to 100L/min.
*1 For multiple outdoor units control system only.
Note: Do not change the setting since it is set according to the specification of Flow sensor
attached to the hydrobox.
Flow sensor setting screen
<Heat source setting>

The default heat source setting is heat pump and all electric heaters present in the system to be
operational. This is referred to as Standard operation on the menu.
Heat source setting screen
<Pump speed>
1. From the Service menu, highlight Pump speed. PUMP SPEED
2. Press CONFIRM.
3. Press F3 and F4 buttons to select a refrigerant address of which you wish to configure or check the
settings, and press CONFIRM. *1
4. The Pump speed screen is displayed.
5. Use F1 and F2 buttons to set the pump speed (1 to 5) of DHW operation.
6. Use F3 and F4 buttons to set the pump speed (1 to 5) of space heating(cooling) operation.
Pump speed setting screen
OCH712C 29
<Operation settings>
Heating operation
This function allows operational setting of flow temperature range from the Ecodan and also the time interval at which the FTC collects and processes data for the auto
adaptation mode.
Menu subtitle Function Range Unit Default

Flow temp. range Minimum temp. To minimize the loss by frequent ON and OFF in mild outdoor ambient tem- 20 to 45 ºC 30
perature seasons.
Maximum temp. To set max. possible flow temperature according to the type of heat emitters. 35 to 60 ºC 50
Room temp. control Mode Setting for Room temp. control Normal/ — Normal
At Fast mode, target outlet water temperature is set higher than the one set Fast
at normal mode. This reduces the time to reach the target room temperature
when the room temperature is relatively low.*1
Interval Selectable according to the heat emitter type and the materials of floor (i.e. 10 to 60 min 10
radiators, floor heating-thick, -thin concrete, wood, etc.)
Heat pump thermo diff.adjust ON/OFF To minimize the loss by frequent ON and OFF in mild outdoor ambient tem- ON/OFF — ON
perature seasons.
Lower limit Prohibits heat pump operation until the flow temperature drops below the −9 to −1 ºC −5
target flow temperature plus lower limit value.
Upper limit Allows heat pump operation until the flow temperature rises above the target +3 to +5 ºC +5
flow temperature plus upper limit value.
< Heating operation (Room temp. control) >

Notes:
1. The minimum flow temperature that prohibits heat pump operation is 20ºC.
2. The maximum flow temperature that allows heat pump operation equals to the maximum temperature set in the Flow temp. range menu.
*1 Fast mode is not efficient and will increase running cost compared to normal mode.
Freeze stat function

Menu subtitle Function/Description
Freeze stat function *2 An operational function to prevent the water circuit from freezing when outdoor ambient temperature drops.
Flow t. The target outlet water temperature at water circuit when operating in Freeze stat function.*3
Outdoor ambient temp. Minimum outdoor ambient temperature which freeze stat function will begin to operate,
(3 to 20ºC) or choose**. If asterisk (**) is chosen freeze stat function is deactivated. (i.e. primary water freeze risk)
*2 When the system is turned off, freeze stat function is not enabled.
*3 Flow t. is fixed to 20°C and unchangeable.
• Range of outdoor ambient temperature at which simultaneous
Simultaneous Operation operation starts is −30 to 10°C (default −15°C).
For periods of very low outside temperature, this mode can be used. Simultaneous • System shall automatically return to routine operation. This will
operation allows both DHW and space heating to run together by using the heat pump happen when the outdoor ambient temperature rises above the
and/or booster heater to provide space heating whilst only the immersion heater selected temperature for this specific mode of operation.
provides heating for DHW. This operation is only available if BOTH a DHW tank AND
immersion heater are present on the system.
Cold weather function

For extremely low outdoor ambient temperature conditions when the heat pump’s capacity is restricted, the heating or DHW is provided only by the electric booster
heater (and immersion if present). This function is intended for use during extreme cold periods only. Extensive use of direct electrical heaters ONLY will result in
higher power consumption and may reduce working life of heaters and related parts.
Target flow temp.
• Range of outdoor ambient temperature at which cold weather function starts (°C)
(h)
is −30 to −10°C (default −15°C).
(g) 45
• System shall automatically return to routine operation. This will happen when (d)
(e)
the outdoor ambient temperature rises above the selected temperature for
this specific mode of operation. 40
35
Floor dry up function (b)
(c)
The Floor dry up function automatically changes the target hot water temperature 30
in stages to gradually dry concrete when this particular type of underfloor heating (f)
system is installed.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Days
pon completion of the operation, the system stops all the operations except the
U
Freeze stat. operation. • This function is not available when a PUHZ-FRP outdoor unit is connected.
For Floor dry up function, the target flow temp. of Zone1 is the same as that of • Disconnect wiring to external inputs of room thermostat, demand control, and
Zone2. outdoor thermostat, or the target flow temperature may not be maintained.
Functions Symbol Description Option/Range Unit Default

Sets the function to ON and power on the system using the main remote
Floor dry up function a ON/OFF — OFF
controller, and the dry up heating operation will start.
Flow temp. Flow temp. increase step b Sets the increase step of the target flow temperature. +1 to +10 ºC +5
(increase) Increase interval c Sets the period for which the same target flow temperature is maintained. 1 to 7 day 2
Flow temp. Flow temp. decrease step d Sets the decrease step of the target flow temperature. −1 to −10 ºC −5
(decrease) Decrease interval e Sets the period for which the same target flow temperature is maintained. 1 to 7 day 2
Start & Finish f Sets the target flow temperature at the start and the finish of the operation. 20 to 60 ºC 30
Target Max. target temp. g Sets the maximum target flow temperature. 20 to 60 ºC 45
temperature Sets the period for which the maximum target flow temperature is main-
Max. temp. period h 1 to 20 day 5
tained.
OCH712C 30
<Energy monitor settings>
1. General description
End user can monitor accumulated (*1) ‘Consumed electrical energy’ and ‘Delivered heat energy’ in each operation mode (*2) on the main remote controller.
*1 Monthly and Year to date
*2 - DHW operation
- Space heating
- Space cooling
Refer to the menu tree in “9-3. Main Settings Menu” for how to check the energy, and “6-6. DIP switch functions” for the details on DIP-SW setting.
Either one of the following 2 methods is used for monitoring.
Note: Method 1 should be used as a guide. If a certain accuracy is required, method 2 should be used.
(1) Calculation internally【Method 1】

Electricity consumption is calculated internally based on the energy consumption of outdoor unit, electric heater, water pump(s) and other auxiliaries.*1
Delivered heat is calculated internally by multiplying delta T (Flow and Return temp.) and flow rate measured by the factory fitted sensors.
Set the electric heater capacity and water pump(s) input according to indoor model name and specs of additional pump(s) supplied locally. (Refer to the menu
tree in “9-3. Main Settings Menu”)
Booster heater1 Booster heater2 Pump1 * 2 Pump2 Pump3

Default 2 kW 4 kW ***(factory fitted pump) 0 kW 0 kW
EHSD-MED 0 kW 0 kW ***
EHSD-VM2D 2 kW 0 kW ***
EHSD-VM6D 2 kW 4 kW ***
EHSD-YM9D 3 kW 6 kW ***
EHSD-YM9ED 3 kW 6 kW ***
EHSD-TM9D 3 kW 6 kW ***
EHSC-MED 0 kW 0 kW ***
EHSC-VM2D 2 kW 0 kW ***
EHSC-VM6D 2 kW 4 kW ***
EHSC-YM9D 3 kW 6 kW ***
EHSC-YM9ED 3 kW 6 kW ***
EHSC-TM9D 3 kW 6 kW ***
ERSD-VM2D 2 kW 0 kW ***
ERSD-VM6D 2 kW 4 kW ***
ERSD-YM9D 3 kW 6 kW ***
ERSC-MED 0 kW 0 kW *** When additional pumps supplied locally are
ERSD-MED 0 kW 0 kW *** connected as Pump2/3, change setting ac-
ERSC-VM2D 2 kW 0 kW *** cording to specs of the pumps.
ERSC-VM6D 2 kW 4 kW ***
ERSC-YM9D 3 kW 6 kW ***
EHSE-MED 0 kW 0 kW ***
EHSE-YM9ED 3 kW 6 kW ***
ERSE-MED 0 kW 0 kW ***
ERSE-YM9ED 3 kW 6 kW ***
EHPX-MED 0 kW 0 kW ***
EHPX-VM2D 2 kW 0 kW ***
EHPX-VM6D 2 kW 4 kW ***
EHPX-YM9D 3 kW 6 kW ***
EHPX-YM9ED 3 kW 6 kW ***
ERPX-MD 0 kW 0 kW ***
ERPX-VM2D 2 kW 0 kW ***
ERPX-VM6D 2 kW 4 kW ***
ERPX-YM9D 3 kW 6 kW ***
*1 When the hydrobox is connected with a PUHZ-FRP or PUMY models, electricity consumption is not calculated internally. To display the electricity consumption,
conduct the method 2.
*2 "***" displayed in the energy monitor setting mode means the factory fitted pump is connected as Pump 1 so that the input is automatically calculated.
When anti-freeze solution (propylene glycol) is used for primary water circuit, set the delivered energy adjustment if necessary.
For further detail of above, refer to the menu tree in “9-3. Main Settings Menu”.
(2) Actual measurement by external meter【Method 2】(locally supplied)

FTC has external input terminals for 2 ‘Electric energy meters’ and a ‘Heat meter’.
If two ‘Electric energy meters’ are connected, the 2 recorded values will be combined at the FTC and shown on the main remote controller.
(e.g. Meter 1 for H/P power line, Meter 2 for heater power line)
Refer to the [Signal inputs] in “6. WIRING DIAGRAM” for more information on connectable electric energy meter and heat meter.
● Connectable electric energy meter and heat meter

▪ Pulse meter type Voltage free contact for 12 VDC detection by FTC (TBI.3 1, 3 and 5 pin have a positive voltage.)
▪ Pulse duration Minimum ON time: 40 ms
Minimum OFF time: 100 ms
▪ Possible unit of pulse 0.1 pulse/kWh 1 pulse/kWh 10 pulse/kWh
100 pulse/kWh 1000 pulse/kWh
Those values can be set by the main remote controller. (Refer to the menu tree in "9-3. Main Settings Menu".)
OCH712C 31
2. Settings using the main remote controller
In this menu, all parameters required to record the consumed electrical energy and the
delivered heat energy which is displayed on the main remote controller can be set. The
parameters are an electric heater capacity, supply power of water pump and heat
meter pulse.
Follow the procedure described in General Operation for the set up operation.
For Pump 1, *** can be also set besides this setting.

In the case *** is selected, the system acknowledges "factory fitted pump" is selected.
Energy monitor settings menu screen
<External input settings>
Demand control(IN4)
The selection of “OFF”, whilst a signal is being sent to IN4, forcefully stops all
the heat source operations and the selection of “Boiler” stops operations of
heat pump and electric heater and performs boiler operation.
Outdoor thermostat (IN5)
The selection of “Heater”, whilst a signal is being sent to IN5, performs External input settings menu screen
electric-heater-only operation and the selection of “Boiler” performs boiler
operation.
Demand control screen
Outdoor thermostat setting screen
<Running information>
This function shows current temperature and other data of main component parts
of both the indoor and outdoor units.
1. From the Service menu highlight Running information.

2. Press CONFIRM.
3. Press F3 and F4 buttons to set the Ref. address. *1
4. Use the function buttons to enter index code for the component to be viewed.
(See the Table 9-4-1 for component index codes.)
5. Press CONFIRM.
<Thermistor reading>
This function shows the current readings of thermistors located on the water and refrigerant circuit
Thermistor Description Thermistor Description

TH1A Zone1 room temperature TH7 Ambient (outdoor) temperature
TH1B Zone2 room temperature THW6 Zone1 flow temperature
TH2 Refrigerant liquid temperature THW7 Zone1 return temperature
THW1 Flow water temperature THW8 Zone2 flow temperature
THW2 Return water temperature THW9 Zone2 return temperature
THW5A DHW tank water temperature (upper) THW10 Mixing tank temperature
THW5B DHW tank water temperature (lower) THWB1 Boiler flow temperature
OCH712C 32
<Summary of settings>
This function shows the current installer/user entered settings.
Abbreviation Explanation Abbreviation Explanation
HWtemp DHW max temperature Z2 mode Operation mode
HWdrop DHW temperature drop - HER (Heating room temperature)
HWtime DHW max operation time - HE (Heating flow temperature)
NO HW DHW mode restriction - HCC (Heating compensation curve)
HWset DHW operation mode (Normal/Eco) - COR (—)
- CO (Cooling flow temperature)
Ltemp Legionella hot water temperature Hroom 1 Heating target room temperature
Lfreq Legionella operation Frequency Hroom 2 Heating target room temperature
Lstart Legionella mode start time Hflow 1 Heating target flow temperature
Ltime Legionella max operation time Hflow 2 Heating target flow temperature
Lkeep Duration of max (Legionella) hot Croom 1 Cooling target room temperature
water temperature Croom 2 Cooling target room temperature
Z1 mode Operation mode Cflow 1 Cooling target flow temperature
- HER (Heating room temperature) Cflow 2 Cooling target flow temperature
- HE (Heating flow temperature) FSflow Freeze stat function flow temperature
- HCC (Heating compensation curve) FSout Freeze stat function ambient temperature
- COR (—)
- CO (Cooling flow temperature)
<Error history>
Error history allows the service engineer to view previous check codes, the unit
address and the date on which they occurred. Up to 16 check codes can be
stored in the history and the most recent Error event is displayed at the top of the Error unit Date
list.
1. From the service menu, select Error history

2. Press CONFIRM.
Please see "10-4. Self diagnosis and action" for check codes diagnosis and
actions.
To delete an Error history item;

1. From Error history screen, press F4 button (Rubbish bin icon)
2. Then press F3 button (Yes).
Error unit Date
<Password protection>
Password protection is available to prevent unauthorised access to the service
menu by untrained persons.
1. From the service menu, use F1 and F2 buttons to scroll through list until
Password protection is highlighted.
2. Press CONFIRM.
3. When password input screen is displayed, use buttons F1 and F2 to move left
and right between the 4 digits, F3 to lower the selected digit by 1, and F4 to in-
crease the selected digit by 1.
4. When you have input your password, press CONFIRM.
5. The password verify screen is displayed. Password input screen
6. To verify your new password, press button F3.
7. Your password is now set and the completion screen is displayed.
Password verify screen
OCH712C 33
Resetting the password
If you forget the password you entered, or have to service a unit somebody else
installed, you can reset the password to the factory default of 0000.
1. From the main settings menu, scroll down the functions until Service Menu is
highlighted.
2. Press CONFIRM.
3. You will be prompted to enter a password.
4. Hold down buttons F3 and F4 together for 3 seconds.
5. You will be asked if you wish to continue and reset the password to default set-
ting.
6. To reset press button F3.
7. The password is now reset to 0000. Completion screen
<Manual reset>
Should you wish to restore the initial settings at any time, you should use the
manual reset function. Please note this will reset ALL functions to the factory de-
fault settings.
1. From the service menu, use F1 and F2 buttons to scroll through list until Manu-
al Reset is highlighted.
2. Press CONFIRM.
3. The Manual reset screen is displayed.
4. Choose either Manual Reset for FTC or Main remote controller.
5. Press F3 button to confirm manual reset of chosen device.
<SD card>
The use of an SD memory card simplifies the main remote controller settings in the
field.
*Ecodan service tool (for use with PC tool) is necessary for the setting.
SD Main RC
1. From the SD card setting, use F1 and F2 buttons to scroll through list until
“SD Main RC” is highlighted.
2. Press CONFIRM.
4. Use F1, F2 and F3 buttons to select a menu to write to the main remote controller.
5. Press CONFIRM to start downloading.
6. Wait for a few minutes until “Complete!” appears.
Main RC SD
1. From the SD card setting, use F1 and F2 buttons to scroll through list until
Main RC SD is highlighted.
2. Press CONFIRM.
4. Use F1, F2 and F3 buttons to select a menu to write to the SD memory card.
5. Press CONFIRM to start uploading.
6. Wait for a few minutes until “Complete!” appears.
OCH712C 34
<Table 9-4-1> Request code in running information
Request
Request content Range Unit
code
103 Error history 1 (latest) Displays error history. ("– –" is displays if no history is present.) Code
104 Error history 2 (second to last) Displays error history. ("– –" is displays if no history is present.) —
105 Error history 3 (third to last) Displays error history. ("– –" is displays if no history is present.) —
154 Water circulation pump 1 - Accumulated operating time (after reset) 0 to 9999 10 hours
162 Indoor unit - DIP SW1 setting information Refer to detail contents described hereinafter. —
175 Indoor unit - Output signal information Refer to detail contents described hereinafter. —
176 Indoor unit - Input signal information Refer to detail contents described hereinafter. —
177 Mixing valve opening step 0 to 10 Step
190 Indoor unit - Software version 1st 4 digits Refer to Note below. —
191 Indoor unit - Software version last 4 digits Refer to Note below. —
200 Initialisation of Function Setting — —
340 Water circulation pump 1 - Accumulated operating time reset — —
504 Indoor unit - Zone1 room temp. (TH1A) −39 to +88 °C
505 Indoor unit - Ref. liquid temp. (TH2) −39 to +88 °C
506 Indoor unit - Return water temp. (THW2) −39 to +88 °C
507 Indoor unit - Zone2 room temp. (TH1B) −39 to +88 °C
508 Indoor unit - DHW tank water temp. (THW5B) −39 to +88 °C
509 Indoor unit - Zone1 flow water temp. (THW6) −39 to +88 °C
510 Indoor unit - Outside air temp. (TH7) −39 to +88 °C
511 Indoor unit - Flow water temp. (THW1) −39 to +88 °C
512 Indoor unit - Zone1 return water temp. (THW7) −39 to +88 °C
513 Indoor unit - Zone2 flow water temp. (THW8) −39 to +88 °C
514 Indoor unit - Zone2 return water temp. (THW9) −39 to +88 °C
515 Indoor unit - Boiler flow water temp. (THWB1) –40 to +140 °C
535 Indoor unit - Mixing tank water temp. (THW10) –40 to +140 °C
540 Flow rate of the primary circuit 0 to 100 L/min
Displays postponement code.
550 Indoor unit - Error postponement history 1 (latest) —
("– –" is displays if no postponement code is present.)
551 Indoor unit - Operation control at time of error 0 Standard, 1 Heater, 2 Boiler —
Indoor unit - Operation mode at time of error 0: OFF, 1: DHW, 2 :Heating, 3: Cooling, 4: Legionella preven-
552 —
tion, 5: Freeze protection, 6: Operation stop, 7: Defrost
553 Indoor unit - Output signal information at time of error Refer to detail contents described hereinafter. —
554 Indoor unit - Input signal information at time of error Refer to detail contents described hereinafter. —
555 Indoor unit - Zone1 room temp. (TH1A) at time of error −39 to +88 °C
556 Indoor unit - Zone2 room temp. (TH1B) at time of error −39 to +88 °C
557 Indoor unit - Ref. liquid temp. (TH2) at time of error −39 to +88 °C
558 Indoor unit - Flow water temp. (THW1) at time of error −39 to +88 °C
559 Indoor unit - Return water temp. (THW2) at time of error −39 to +88 °C
560 Indoor unit - DHW tank water temp. (THW5B) at time of error −39 to +88 °C
561 Indoor unit - Zone1 flow water temp. (THW6) at time of error −39 to +88 °C
562 Indoor unit - Zone1 return water temp. (THW7) at time of error −39 to +88 °C
563 Indoor unit - Zone2 flow water temp. (THW8) at time of error −39 to +88 °C
564 Indoor unit - Zone2 return water temp. (THW9) at time of error −39 to +88 °C
565 Indoor unit - Boiler flow water temp. (THWB1) at time of error –40 to +140 °C
Indoor unit - Failure (P1/P2/L5/L8/Ld) thermistor 0: Failure thermistor is none, 1: TH1A, 2: TH2, 3: THW1,
567 4: THW2, 5: THWB1, 6: THW5B, 8: TH1B, A: THW6, B: THW7, —
C: THW8, D: THW9
568 Mixing valve opening step at time of error 0 to +10 Step
Operated Flow switch at time of failure (L9) 0: No operated flow switch, 1: Flow switch 1, 2: Flow switch 2,
569 —
3: Flow switch 3
571 Flow rate at time of error 0 to +100 L/min
Note:
Refer to outdoor unit service manual for request code 0 to 102, 106 to 149.
Request codes 103 to 105 indicate error histories of both indoor and outdoor units.
As only 4 digits can be displayed at one time the software version number is displayed in two halves.
Enter code 190 to see the first 4 digits and code 191 to see the last 4 digits.
For example software version No. 5.01 A000, when code 190 is entered 0501 is displayed, when code 191 is entered A000 is displayed.
Request code 200 resets all Function Setting to the factory default settings.
OCH712C 35
Indoor unit switch setting display (Request code: 162 to 166)
0: OFF 1: ON 0: OFF 1: ON
SW1, SW2, SW3, SW4, SW5 SW1, SW2, SW3, SW4, SW5
Display Display
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
0 0 0 0 0 0 0 0 00 00 0 0 0 0 0 0 1 0 00 40
1 0 0 0 0 0 0 0 00 01 1 0 0 0 0 0 1 0 00 41
0 1 0 0 0 0 0 0 00 02 0 1 0 0 0 0 1 0 00 42
1 1 0 0 0 0 0 0 00 03 1 1 0 0 0 0 1 0 00 43
0 0 1 0 0 0 0 0 00 04 0 0 1 0 0 0 1 0 00 44
1 0 1 0 0 0 0 0 00 05 1 0 1 0 0 0 1 0 00 45
0 1 1 0 0 0 0 0 00 06 0 1 1 0 0 0 1 0 00 46
1 1 1 0 0 0 0 0 00 07 1 1 1 0 0 0 1 0 00 47
0 0 0 1 0 0 0 0 00 08 0 0 0 1 0 0 1 0 00 48
1 0 0 1 0 0 0 0 00 09 1 0 0 1 0 0 1 0 00 49
0 1 0 1 0 0 0 0 00 0A 0 1 0 1 0 0 1 0 00 4A
1 1 0 1 0 0 0 0 00 0B 1 1 0 1 0 0 1 0 00 4B
0 0 1 1 0 0 0 0 00 0C 0 0 1 1 0 0 1 0 00 4C
1 0 1 1 0 0 0 0 00 0D 1 0 1 1 0 0 1 0 00 4D
0 1 1 1 0 0 0 0 00 0E 0 1 1 1 0 0 1 0 00 4E
1 1 1 1 0 0 0 0 00 0F 1 1 1 1 0 0 1 0 00 4F
0 0 0 0 1 0 0 0 00 10 0 0 0 0 1 0 1 0 00 50
1 0 0 0 1 0 0 0 00 11 1 0 0 0 1 0 1 0 00 51
0 1 0 0 1 0 0 0 00 12 0 1 0 0 1 0 1 0 00 52
1 1 0 0 1 0 0 0 00 13 1 1 0 0 1 0 1 0 00 53
0 0 1 0 1 0 0 0 00 14 0 0 1 0 1 0 1 0 00 54
1 0 1 0 1 0 0 0 00 15 1 0 1 0 1 0 1 0 00 55
0 1 1 0 1 0 0 0 00 16 0 1 1 0 1 0 1 0 00 56
1 1 1 0 1 0 0 0 00 17 1 1 1 0 1 0 1 0 00 57
0 0 0 1 1 0 0 0 00 18 0 0 0 1 1 0 1 0 00 58
1 0 0 1 1 0 0 0 00 19 1 0 0 1 1 0 1 0 00 59
0 1 0 1 1 0 0 0 00 1A 0 1 0 1 1 0 1 0 00 5A
1 1 0 1 1 0 0 0 00 1B 1 1 0 1 1 0 1 0 00 5B
0 0 1 1 1 0 0 0 00 1C 0 0 1 1 1 0 1 0 00 5C
1 0 1 1 1 0 0 0 00 1D 1 0 1 1 1 0 1 0 00 5D
0 1 1 1 1 0 0 0 00 1E 0 1 1 1 1 0 1 0 00 5E
1 1 1 1 1 0 0 0 00 1F 1 1 1 1 1 0 1 0 00 5F
0 0 0 0 0 1 0 0 00 20 0 0 0 0 0 1 1 0 00 60
1 0 0 0 0 1 0 0 00 21 1 0 0 0 0 1 1 0 00 61
0 1 0 0 0 1 0 0 00 22 0 1 0 0 0 1 1 0 00 62
1 1 0 0 0 1 0 0 00 23 1 1 0 0 0 1 1 0 00 63
0 0 1 0 0 1 0 0 00 24 0 0 1 0 0 1 1 0 00 64
1 0 1 0 0 1 0 0 00 25 1 0 1 0 0 1 1 0 00 65
0 1 1 0 0 1 0 0 00 26 0 1 1 0 0 1 1 0 00 66
1 1 1 0 0 1 0 0 00 27 1 1 1 0 0 1 1 0 00 67
0 0 0 1 0 1 0 0 00 28 0 0 0 1 0 1 1 0 00 68
1 0 0 1 0 1 0 0 00 29 1 0 0 1 0 1 1 0 00 69
0 1 0 1 0 1 0 0 00 2A 0 1 0 1 0 1 1 0 00 6A
1 1 0 1 0 1 0 0 00 2B 1 1 0 1 0 1 1 0 00 6B
0 0 1 1 0 1 0 0 00 2C 0 0 1 1 0 1 1 0 00 6C
1 0 1 1 0 1 0 0 00 2D 1 0 1 1 0 1 1 0 00 6D
0 1 1 1 0 1 0 0 00 2E 0 1 1 1 0 1 1 0 00 6E
1 1 1 1 0 1 0 0 00 2F 1 1 1 1 0 1 1 0 00 6F
0 0 0 0 1 1 0 0 00 30 0 0 0 0 1 1 1 0 00 70
1 0 0 0 1 1 0 0 00 31 1 0 0 0 1 1 1 0 00 71
0 1 0 0 1 1 0 0 00 32 0 1 0 0 1 1 1 0 00 72
1 1 0 0 1 1 0 0 00 33 1 1 0 0 1 1 1 0 00 73
0 0 1 0 1 1 0 0 00 34 0 0 1 0 1 1 1 0 00 74
1 0 1 0 1 1 0 0 00 35 1 0 1 0 1 1 1 0 00 75
0 1 1 0 1 1 0 0 00 36 0 1 1 0 1 1 1 0 00 76
1 1 1 0 1 1 0 0 00 37 1 1 1 0 1 1 1 0 00 77
0 0 0 1 1 1 0 0 00 38 0 0 0 1 1 1 1 0 00 78
1 0 0 1 1 1 0 0 00 39 1 0 0 1 1 1 1 0 00 79
0 1 0 1 1 1 0 0 00 3A 0 1 0 1 1 1 1 0 00 7A
1 1 0 1 1 1 0 0 00 3B 1 1 0 1 1 1 1 0 00 7B
0 0 1 1 1 1 0 0 00 3C 0 0 1 1 1 1 1 0 00 7C
1 0 1 1 1 1 0 0 00 3D 1 0 1 1 1 1 1 0 00 7D
0 1 1 1 1 1 0 0 00 3E 0 1 1 1 1 1 1 0 00 7E
1 1 1 1 1 1 0 0 00 3F 1 1 1 1 1 1 1 0 00 7F
OCH712C 36
Indoor unit switch setting display (Request code: 162 to 166)
SW1, SW2, SW3, SW4, SW5 SW1, SW2, SW3, SW4, SW5
Display Display
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
0 0 0 0 0 0 0 1 00 80 0 0 0 0 0 0 1 1 00 C0
1 0 0 0 0 0 0 1 00 81 1 0 0 0 0 0 1 1 00 C1
0 1 0 0 0 0 0 1 00 82 0 1 0 0 0 0 1 1 00 C2
1 1 0 0 0 0 0 1 00 83 1 1 0 0 0 0 1 1 00 C3
0 0 1 0 0 0 0 1 00 84 0 0 1 0 0 0 1 1 00 C4
1 0 1 0 0 0 0 1 00 85 1 0 1 0 0 0 1 1 00 C5
0 1 1 0 0 0 0 1 00 86 0 1 1 0 0 0 1 1 00 C6
1 1 1 0 0 0 0 1 00 87 1 1 1 0 0 0 1 1 00 C7
0 0 0 1 0 0 0 1 00 88 0 0 0 1 0 0 1 1 00 C8
1 0 0 1 0 0 0 1 00 89 1 0 0 1 0 0 1 1 00 C9
0 1 0 1 0 0 0 1 00 8A 0 1 0 1 0 0 1 1 00 CA
1 1 0 1 0 0 0 1 00 8B 1 1 0 1 0 0 1 1 00 CB
0 0 1 1 0 0 0 1 00 8C 0 0 1 1 0 0 1 1 00 CC
1 0 1 1 0 0 0 1 00 8D 1 0 1 1 0 0 1 1 00 CD
0 1 1 1 0 0 0 1 00 8E 0 1 1 1 0 0 1 1 00 CE
1 1 1 1 0 0 0 1 00 8F 1 1 1 1 0 0 1 1 00 CF
0 0 0 0 1 0 0 1 00 90 0 0 0 0 1 0 1 1 00 D0
1 0 0 0 1 0 0 1 00 91 1 0 0 0 1 0 1 1 00 D1
0 1 0 0 1 0 0 1 00 92 0 1 0 0 1 0 1 1 00 D2
1 1 0 0 1 0 0 1 00 93 1 1 0 0 1 0 1 1 00 D3
0 0 1 0 1 0 0 1 00 94 0 0 1 0 1 0 1 1 00 D4
1 0 1 0 1 0 0 1 00 95 1 0 1 0 1 0 1 1 00 D5
0 1 1 0 1 0 0 1 00 96 0 1 1 0 1 0 1 1 00 D6
1 1 1 0 1 0 0 1 00 97 1 1 1 0 1 0 1 1 00 D7
0 0 0 1 1 0 0 1 00 98 0 0 0 1 1 0 1 1 00 D8
1 0 0 1 1 0 0 1 00 99 1 0 0 1 1 0 1 1 00 D9
0 1 0 1 1 0 0 1 00 9A 0 1 0 1 1 0 1 1 00 DA
1 1 0 1 1 0 0 1 00 9B 1 1 0 1 1 0 1 1 00 DB
0 0 1 1 1 0 0 1 00 9C 0 0 1 1 1 0 1 1 00 DC
1 0 1 1 1 0 0 1 00 9D 1 0 1 1 1 0 1 1 00 DD
0 1 1 1 1 0 0 1 00 9E 0 1 1 1 1 0 1 1 00 DE
1 1 1 1 1 0 0 1 00 9F 1 1 1 1 1 0 1 1 00 DF
0 0 0 0 0 1 0 1 00 A0 0 0 0 0 0 1 1 1 00 E0
1 0 0 0 0 1 0 1 00 A1 1 0 0 0 0 1 1 1 00 E1
0 1 0 0 0 1 0 1 00 A2 0 1 0 0 0 1 1 1 00 E2
1 1 0 0 0 1 0 1 00 A3 1 1 0 0 0 1 1 1 00 E3
0 0 1 0 0 1 0 1 00 A4 0 0 1 0 0 1 1 1 00 E4
1 0 1 0 0 1 0 1 00 A5 1 0 1 0 0 1 1 1 00 E5
0 1 1 0 0 1 0 1 00 A6 0 1 1 0 0 1 1 1 00 E6
1 1 1 0 0 1 0 1 00 A7 1 1 1 0 0 1 1 1 00 E7
0 0 0 1 0 1 0 1 00 A8 0 0 0 1 0 1 1 1 00 E8
1 0 0 1 0 1 0 1 00 A9 1 0 0 1 0 1 1 1 00 E9
0 1 0 1 0 1 0 1 00 AA 0 1 0 1 0 1 1 1 00 EA
1 1 0 1 0 1 0 1 00 AB 1 1 0 1 0 1 1 1 00 EB
0 0 1 1 0 1 0 1 00 AC 0 0 1 1 0 1 1 1 00 EC
1 0 1 1 0 1 0 1 00 AD 1 0 1 1 0 1 1 1 00 ED
0 1 1 1 0 1 0 1 00 AE 0 1 1 1 0 1 1 1 00 EE
1 1 1 1 0 1 0 1 00 AF 1 1 1 1 0 1 1 1 00 EF
0 0 0 0 1 1 0 1 00 B0 0 0 0 0 1 1 1 1 00 F0
1 0 0 0 1 1 0 1 00 B1 1 0 0 0 1 1 1 1 00 F1
0 1 0 0 1 1 0 1 00 B2 0 1 0 0 1 1 1 1 00 F2
1 1 0 0 1 1 0 1 00 B3 1 1 0 0 1 1 1 1 00 F3
0 0 1 0 1 1 0 1 00 B4 0 0 1 0 1 1 1 1 00 F4
1 0 1 0 1 1 0 1 00 B5 1 0 1 0 1 1 1 1 00 F5
0 1 1 0 1 1 0 1 00 B6 0 1 1 0 1 1 1 1 00 F6
1 1 1 0 1 1 0 1 00 B7 1 1 1 0 1 1 1 1 00 F7
0 0 0 1 1 1 0 1 00 B8 0 0 0 1 1 1 1 1 00 F8
1 0 0 1 1 1 0 1 00 B9 1 0 0 1 1 1 1 1 00 F9
0 1 0 1 1 1 0 1 00 BA 0 1 0 1 1 1 1 1 00 FA
1 1 0 1 1 1 0 1 00 BB 1 1 0 1 1 1 1 1 00 FB
0 0 1 1 1 1 0 1 00 BC 0 0 1 1 1 1 1 1 00 FC
1 0 1 1 1 1 0 1 00 BD 1 0 1 1 1 1 1 1 00 FD
0 1 1 1 1 1 0 1 00 BE 0 1 1 1 1 1 1 1 00 FE
1 1 1 1 1 1 0 1 00 BF 1 1 1 1 1 1 1 1 00 FF
OCH712C 37
Output signal display (Request code: 175/553)
Please refer to Table 2 on relevant wiring diagram whilst using the following.
OUT OUT
Display Display
1 2 3 4 5A 5B 6 7 1 2 3 4 5A 5B 6 7
0 0 0 0 0 0 0 0 xx 00 0 0 0 0 0 0 1 0 xx 40
1 0 0 0 0 0 0 0 xx 01 1 0 0 0 0 0 1 0 xx 41
0 1 0 0 0 0 0 0 xx 02 0 1 0 0 0 0 1 0 xx 42
1 1 0 0 0 0 0 0 xx 03 1 1 0 0 0 0 1 0 xx 43
0 0 1 0 0 0 0 0 xx 04 0 0 1 0 0 0 1 0 xx 44
1 0 1 0 0 0 0 0 xx 05 1 0 1 0 0 0 1 0 xx 45
0 1 1 0 0 0 0 0 xx 06 0 1 1 0 0 0 1 0 xx 46
1 1 1 0 0 0 0 0 xx 07 1 1 1 0 0 0 1 0 xx 47
0 0 0 1 0 0 0 0 xx 08 0 0 0 1 0 0 1 0 xx 48
1 0 0 1 0 0 0 0 xx 09 1 0 0 1 0 0 1 0 xx 49
0 1 0 1 0 0 0 0 xx 0A 0 1 0 1 0 0 1 0 xx 4A
1 1 0 1 0 0 0 0 xx 0B 1 1 0 1 0 0 1 0 xx 4B
0 0 1 1 0 0 0 0 xx 0C 0 0 1 1 0 0 1 0 xx 4C
1 0 1 1 0 0 0 0 xx 0D 1 0 1 1 0 0 1 0 xx 4D
0 1 1 1 0 0 0 0 xx 0E 0 1 1 1 0 0 1 0 xx 4E
1 1 1 1 0 0 0 0 xx 0F 1 1 1 1 0 0 1 0 xx 4F
0 0 0 0 1 0 0 0 xx 10 0 0 0 0 1 0 1 0 xx 50
1 0 0 0 1 0 0 0 xx 11 1 0 0 0 1 0 1 0 xx 51
0 1 0 0 1 0 0 0 xx 12 0 1 0 0 1 0 1 0 xx 52
1 1 0 0 1 0 0 0 xx 13 1 1 0 0 1 0 1 0 xx 53
0 0 1 0 1 0 0 0 xx 14 0 0 1 0 1 0 1 0 xx 54
1 0 1 0 1 0 0 0 xx 15 1 0 1 0 1 0 1 0 xx 55
0 1 1 0 1 0 0 0 xx 16 0 1 1 0 1 0 1 0 xx 56
1 1 1 0 1 0 0 0 xx 17 1 1 1 0 1 0 1 0 xx 57
0 0 0 1 1 0 0 0 xx 18 0 0 0 1 1 0 1 0 xx 58
1 0 0 1 1 0 0 0 xx 19 1 0 0 1 1 0 1 0 xx 59
0 1 0 1 1 0 0 0 xx 1A 0 1 0 1 1 0 1 0 xx 5A
1 1 0 1 1 0 0 0 xx 1B 1 1 0 1 1 0 1 0 xx 5B
0 0 1 1 1 0 0 0 xx 1C 0 0 1 1 1 0 1 0 xx 5C
1 0 1 1 1 0 0 0 xx 1D 1 0 1 1 1 0 1 0 xx 5D
0 1 1 1 1 0 0 0 xx 1E 0 1 1 1 1 0 1 0 xx 5E
1 1 1 1 1 0 0 0 xx 1F 1 1 1 1 1 0 1 0 xx 5F
0 0 0 0 0 1 0 0 xx 20 0 0 0 0 0 1 1 0 xx 60
1 0 0 0 0 1 0 0 xx 21 1 0 0 0 0 1 1 0 xx 61
0 1 0 0 0 1 0 0 xx 22 0 1 0 0 0 1 1 0 xx 62
1 1 0 0 0 1 0 0 xx 23 1 1 0 0 0 1 1 0 xx 63
0 0 1 0 0 1 0 0 xx 24 0 0 1 0 0 1 1 0 xx 64
1 0 1 0 0 1 0 0 xx 25 1 0 1 0 0 1 1 0 xx 65
0 1 1 0 0 1 0 0 xx 26 0 1 1 0 0 1 1 0 xx 66
1 1 1 0 0 1 0 0 xx 27 1 1 1 0 0 1 1 0 xx 67
0 0 0 1 0 1 0 0 xx 28 0 0 0 1 0 1 1 0 xx 68
1 0 0 1 0 1 0 0 xx 29 1 0 0 1 0 1 1 0 xx 69
0 1 0 1 0 1 0 0 xx 2A 0 1 0 1 0 1 1 0 xx 6A
1 1 0 1 0 1 0 0 xx 2B 1 1 0 1 0 1 1 0 xx 6B
0 0 1 1 0 1 0 0 xx 2C 0 0 1 1 0 1 1 0 xx 6C
1 0 1 1 0 1 0 0 xx 2D 1 0 1 1 0 1 1 0 xx 6D
0 1 1 1 0 1 0 0 xx 2E 0 1 1 1 0 1 1 0 xx 6E
1 1 1 1 0 1 0 0 xx 2F 1 1 1 1 0 1 1 0 xx 6F
0 0 0 0 1 1 0 0 xx 30 0 0 0 0 1 1 1 0 xx 70
1 0 0 0 1 1 0 0 xx 31 1 0 0 0 1 1 1 0 xx 71
0 1 0 0 1 1 0 0 xx 32 0 1 0 0 1 1 1 0 xx 72
1 1 0 0 1 1 0 0 xx 33 1 1 0 0 1 1 1 0 xx 73
0 0 1 0 1 1 0 0 xx 34 0 0 1 0 1 1 1 0 xx 74
1 0 1 0 1 1 0 0 xx 35 1 0 1 0 1 1 1 0 xx 75
0 1 1 0 1 1 0 0 xx 36 0 1 1 0 1 1 1 0 xx 76
1 1 1 0 1 1 0 0 xx 37 1 1 1 0 1 1 1 0 xx 77
0 0 0 1 1 1 0 0 xx 38 0 0 0 1 1 1 1 0 xx 78
1 0 0 1 1 1 0 0 xx 39 1 0 0 1 1 1 1 0 xx 79
0 1 0 1 1 1 0 0 xx 3A 0 1 0 1 1 1 1 0 xx 7A
1 1 0 1 1 1 0 0 xx 3B 1 1 0 1 1 1 1 0 xx 7B
0 0 1 1 1 1 0 0 xx 3C 0 0 1 1 1 1 1 0 xx 7C
1 0 1 1 1 1 0 0 xx 3D 1 0 1 1 1 1 1 0 xx 7D
0 1 1 1 1 1 0 0 xx 3E 0 1 1 1 1 1 1 0 xx 7E
1 1 1 1 1 1 0 0 xx 3F 1 1 1 1 1 1 1 0 xx 7F
OCH712C 38
Output signal display (Request code: 175/553)
OUT OUT
Display Display
1 2 3 4 5A 5B 6 7 1 2 3 4 5A 5B 6 7
0 0 0 0 0 0 0 1 xx 80 0 0 0 0 0 0 1 1 xx C0
1 0 0 0 0 0 0 1 xx 81 1 0 0 0 0 0 1 1 xx C1
0 1 0 0 0 0 0 1 xx 82 0 1 0 0 0 0 1 1 xx C2
1 1 0 0 0 0 0 1 xx 83 1 1 0 0 0 0 1 1 xx C3
0 0 1 0 0 0 0 1 xx 84 0 0 1 0 0 0 1 1 xx C4
1 0 1 0 0 0 0 1 xx 85 1 0 1 0 0 0 1 1 xx C5
0 1 1 0 0 0 0 1 xx 86 0 1 1 0 0 0 1 1 xx C6
1 1 1 0 0 0 0 1 xx 87 1 1 1 0 0 0 1 1 xx C7
0 0 0 1 0 0 0 1 xx 88 0 0 0 1 0 0 1 1 xx C8
1 0 0 1 0 0 0 1 xx 89 1 0 0 1 0 0 1 1 xx C9
0 1 0 1 0 0 0 1 xx 8A 0 1 0 1 0 0 1 1 xx CA
1 1 0 1 0 0 0 1 xx 8B 1 1 0 1 0 0 1 1 xx CB
0 0 1 1 0 0 0 1 xx 8C 0 0 1 1 0 0 1 1 xx CC
1 0 1 1 0 0 0 1 xx 8D 1 0 1 1 0 0 1 1 xx CD
0 1 1 1 0 0 0 1 xx 8E 0 1 1 1 0 0 1 1 xx CE
1 1 1 1 0 0 0 1 xx 8F 1 1 1 1 0 0 1 1 xx CF
0 0 0 0 1 0 0 1 xx 90 0 0 0 0 1 0 1 1 xx D0
1 0 0 0 1 0 0 1 xx 91 1 0 0 0 1 0 1 1 xx D1
0 1 0 0 1 0 0 1 xx 92 0 1 0 0 1 0 1 1 xx D2
1 1 0 0 1 0 0 1 xx 93 1 1 0 0 1 0 1 1 xx D3
0 0 1 0 1 0 0 1 xx 94 0 0 1 0 1 0 1 1 xx D4
1 0 1 0 1 0 0 1 xx 95 1 0 1 0 1 0 1 1 xx D5
0 1 1 0 1 0 0 1 xx 96 0 1 1 0 1 0 1 1 xx D6
1 1 1 0 1 0 0 1 xx 97 1 1 1 0 1 0 1 1 xx D7
0 0 0 1 1 0 0 1 xx 98 0 0 0 1 1 0 1 1 xx D8
1 0 0 1 1 0 0 1 xx 99 1 0 0 1 1 0 1 1 xx D9
0 1 0 1 1 0 0 1 xx 9A 0 1 0 1 1 0 1 1 xx DA
1 1 0 1 1 0 0 1 xx 9B 1 1 0 1 1 0 1 1 xx DB
0 0 1 1 1 0 0 1 xx 9C 0 0 1 1 1 0 1 1 xx DC
1 0 1 1 1 0 0 1 xx 9D 1 0 1 1 1 0 1 1 xx DD
0 1 1 1 1 0 0 1 xx 9E 0 1 1 1 1 0 1 1 xx DE
1 1 1 1 1 0 0 1 xx 9F 1 1 1 1 1 0 1 1 xx DF
0 0 0 0 0 1 0 1 xx A0 0 0 0 0 0 1 1 1 xx E0
1 0 0 0 0 1 0 1 xx A1 1 0 0 0 0 1 1 1 xx E1
0 1 0 0 0 1 0 1 xx A2 0 1 0 0 0 1 1 1 xx E2
1 1 0 0 0 1 0 1 xx A3 1 1 0 0 0 1 1 1 xx E3
0 0 1 0 0 1 0 1 xx A4 0 0 1 0 0 1 1 1 xx E4
1 0 1 0 0 1 0 1 xx A5 1 0 1 0 0 1 1 1 xx E5
0 1 1 0 0 1 0 1 xx A6 0 1 1 0 0 1 1 1 xx E6
1 1 1 0 0 1 0 1 xx A7 1 1 1 0 0 1 1 1 xx E7
0 0 0 1 0 1 0 1 xx A8 0 0 0 1 0 1 1 1 xx E8
1 0 0 1 0 1 0 1 xx A9 1 0 0 1 0 1 1 1 xx E9
0 1 0 1 0 1 0 1 xx AA 0 1 0 1 0 1 1 1 xx EA
1 1 0 1 0 1 0 1 xx AB 1 1 0 1 0 1 1 1 xx EB
0 0 1 1 0 1 0 1 xx AC 0 0 1 1 0 1 1 1 xx EC
1 0 1 1 0 1 0 1 xx AD 1 0 1 1 0 1 1 1 xx ED
0 1 1 1 0 1 0 1 xx AE 0 1 1 1 0 1 1 1 xx EE
1 1 1 1 0 1 0 1 xx AF 1 1 1 1 0 1 1 1 xx EF
0 0 0 0 1 1 0 1 xx B0 0 0 0 0 1 1 1 1 xx F0
1 0 0 0 1 1 0 1 xx B1 1 0 0 0 1 1 1 1 xx F1
0 1 0 0 1 1 0 1 xx B2 0 1 0 0 1 1 1 1 xx F2
1 1 0 0 1 1 0 1 xx B3 1 1 0 0 1 1 1 1 xx F3
0 0 1 0 1 1 0 1 xx B4 0 0 1 0 1 1 1 1 xx F4
1 0 1 0 1 1 0 1 xx B5 1 0 1 0 1 1 1 1 xx F5
0 1 1 0 1 1 0 1 xx B6 0 1 1 0 1 1 1 1 xx F6
1 1 1 0 1 1 0 1 xx B7 1 1 1 0 1 1 1 1 xx F7
0 0 0 1 1 1 0 1 xx B8 0 0 0 1 1 1 1 1 xx F8
1 0 0 1 1 1 0 1 xx B9 1 0 0 1 1 1 1 1 xx F9
0 1 0 1 1 1 0 1 xx BA 0 1 0 1 1 1 1 1 xx FA
1 1 0 1 1 1 0 1 xx BB 1 1 0 1 1 1 1 1 xx FB
0 0 1 1 1 1 0 1 xx BC 0 0 1 1 1 1 1 1 xx FC
1 0 1 1 1 1 0 1 xx BD 1 0 1 1 1 1 1 1 xx FD
0 1 1 1 1 1 0 1 xx BE 0 1 1 1 1 1 1 1 xx FE
1 1 1 1 1 1 0 1 xx BF 1 1 1 1 1 1 1 1 xx FF
OCH712C 39
OUT
Output signal display (Request code: 175/553) Display
8 9 10 11 12 13 14 15
0 0 0 0 0 0 1 0 40 xx
1 0 0 0 0 0 1 0 41 xx
0: OFF 1: ON 0 1 0 0 0 0 1 0 42 xx
OUT 1 1 0 0 0 0 1 0 43 xx
Display 0 0 1 0 0 0 1 0 44 xx
8* 9 10 11 12 13 14 15
0 0 0 0 0 0 0 0 00 xx 1 0 1 0 0 0 1 0 45 xx
1 0 0 0 0 0 0 0 01 xx 0 1 1 0 0 0 1 0 46 xx
0 1 0 0 0 0 0 0 02 xx 1 1 1 0 0 0 1 0 47 xx
1 1 0 0 0 0 0 0 03 xx 0 0 0 1 0 0 1 0 48 xx
0 0 1 0 0 0 0 0 04 xx 1 0 0 1 0 0 1 0 49 xx
1 0 1 0 0 0 0 0 05 xx 0 1 0 1 0 0 1 0 4A xx
0 1 1 0 0 0 0 0 06 xx 1 1 0 1 0 0 1 0 4B xx
1 1 1 0 0 0 0 0 07 xx 0 0 1 1 0 0 1 0 4C xx
0 0 0 1 0 0 0 0 08 xx 1 0 1 1 0 0 1 0 4D xx
1 0 0 1 0 0 0 0 09 xx 0 1 1 1 0 0 1 0 4E xx
0 1 0 1 0 0 0 0 0A xx 1 1 1 1 0 0 1 0 4F xx
1 1 0 1 0 0 0 0 0B xx 0 0 0 0 1 0 1 0 50 xx
0 0 1 1 0 0 0 0 0C xx 1 0 0 0 1 0 1 0 51 xx
1 0 1 1 0 0 0 0 0D xx 0 1 0 0 1 0 1 0 52 xx
0 1 1 1 0 0 0 0 0E xx 1 1 0 0 1 0 1 0 53 xx
1 1 1 1 0 0 0 0 0F xx 0 0 1 0 1 0 1 0 54 xx
0 0 0 0 1 0 0 0 10 xx 1 0 1 0 1 0 1 0 55 xx
1 0 0 0 1 0 0 0 11 xx 0 1 1 0 1 0 1 0 56 xx
0 1 0 0 1 0 0 0 12 xx 1 1 1 0 1 0 1 0 57 xx
1 1 0 0 1 0 0 0 13 xx 0 0 0 1 1 0 1 0 58 xx
0 0 1 0 1 0 0 0 14 xx 1 0 0 1 1 0 1 0 59 xx
1 0 1 0 1 0 0 0 15 xx 0 1 0 1 1 0 1 0 5A xx
0 1 1 0 1 0 0 0 16 xx 1 1 0 1 1 0 1 0 5B xx
1 1 1 0 1 0 0 0 17 xx 0 0 1 1 1 0 1 0 5C xx
0 0 0 1 1 0 0 0 18 xx 1 0 1 1 1 0 1 0 5D xx
1 0 0 1 1 0 0 0 19 xx 0 1 1 1 1 0 1 0 5E xx
0 1 0 1 1 0 0 0 1A xx 1 1 1 1 1 0 1 0 5F xx
1 1 0 1 1 0 0 0 1B xx 0 0 0 0 0 1 1 0 60 xx
0 0 1 1 1 0 0 0 1C xx 1 0 0 0 0 1 1 0 61 xx
1 0 1 1 1 0 0 0 1D xx 0 1 0 0 0 1 1 0 62 xx
0 1 1 1 1 0 0 0 1E xx 1 1 0 0 0 1 1 0 63 xx
1 1 1 1 1 0 0 0 1F xx 0 0 1 0 0 1 1 0 64 xx
0 0 0 0 0 1 0 0 20 xx 1 0 1 0 0 1 1 0 65 xx
1 0 0 0 0 1 0 0 21 xx 0 1 1 0 0 1 1 0 66 xx
0 1 0 0 0 1 0 0 22 xx 1 1 1 0 0 1 1 0 67 xx
1 1 0 0 0 1 0 0 23 xx 0 0 0 1 0 1 1 0 68 xx
0 0 1 0 0 1 0 0 24 xx 1 0 0 1 0 1 1 0 69 xx
1 0 1 0 0 1 0 0 25 xx 0 1 0 1 0 1 1 0 6A xx
0 1 1 0 0 1 0 0 26 xx 1 1 0 1 0 1 1 0 6B xx
1 1 1 0 0 1 0 0 27 xx 0 0 1 1 0 1 1 0 6C xx
0 0 0 1 0 1 0 0 28 xx 1 0 1 1 0 1 1 0 6D xx
1 0 0 1 0 1 0 0 29 xx 0 1 1 1 0 1 1 0 6E xx
0 1 0 1 0 1 0 0 2A xx 1 1 1 1 0 1 1 0 6F xx
1 1 0 1 0 1 0 0 2B xx 0 0 0 0 1 1 1 0 70 xx
0 0 1 1 0 1 0 0 2C xx 1 0 0 0 1 1 1 0 71 xx
1 0 1 1 0 1 0 0 2D xx 0 1 0 0 1 1 1 0 72 xx
0 1 1 1 0 1 0 0 2E xx 1 1 0 0 1 1 1 0 73 xx
1 1 1 1 0 1 0 0 2F xx 0 0 1 0 1 1 1 0 74 xx
0 0 0 0 1 1 0 0 30 xx 1 0 1 0 1 1 1 0 75 xx
1 0 0 0 1 1 0 0 31 xx 0 1 1 0 1 1 1 0 76 xx
0 1 0 0 1 1 0 0 32 xx 1 1 1 0 1 1 1 0 77 xx
1 1 0 0 1 1 0 0 33 xx 0 0 0 1 1 1 1 0 78 xx
0 0 1 0 1 1 0 0 34 xx 1 0 0 1 1 1 1 0 79 xx
1 0 1 0 1 1 0 0 35 xx 0 1 0 1 1 1 1 0 7A xx
0 1 1 0 1 1 0 0 36 xx 1 1 0 1 1 1 1 0 7B xx
1 1 1 0 1 1 0 0 37 xx 0 0 1 1 1 1 1 0 7C xx
0 0 0 1 1 1 0 0 38 xx 1 0 1 1 1 1 1 0 7D xx
1 0 0 1 1 1 0 0 39 xx 0 1 1 1 1 1 1 0 7E xx
0 1 0 1 1 1 0 0 3A xx 1 1 1 1 1 1 1 0 7F xx
1 1 0 1 1 1 0 0 3B xx Mixing valve state
0 0 1 1 1 1 0 0 3C xx
OUT
1 0 1 1 1 1 0 0 3D xx Mixing valve state
5A 5B
0 1 1 1 1 1 0 0 3E xx
0 0 Stop
1 1 1 1 1 1 0 0 3F xx
0 1 Stop
* Displayed only when the request code is 533.
1 0 Open
1 1 Close
OCH712C 40
Input signal display (Request code: 176/554)
0: OFF (open) 1: ON (short) 0: OFF (open) 1: ON (short)

IN IN
Display Display
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
0 0 0 0 0 0 0 0 00 00 0 0 0 0 0 0 1 0 00 40
1 0 0 0 0 0 0 0 00 01 1 0 0 0 0 0 1 0 00 41
0 1 0 0 0 0 0 0 00 02 0 1 0 0 0 0 1 0 00 42
1 1 0 0 0 0 0 0 00 03 1 1 0 0 0 0 1 0 00 43
0 0 1 0 0 0 0 0 00 04 0 0 1 0 0 0 1 0 00 44
1 0 1 0 0 0 0 0 00 05 1 0 1 0 0 0 1 0 00 45
0 1 1 0 0 0 0 0 00 06 0 1 1 0 0 0 1 0 00 46
1 1 1 0 0 0 0 0 00 07 1 1 1 0 0 0 1 0 00 47
0 0 0 1 0 0 0 0 00 08 0 0 0 1 0 0 1 0 00 48
1 0 0 1 0 0 0 0 00 09 1 0 0 1 0 0 1 0 00 49
0 1 0 1 0 0 0 0 00 0A 0 1 0 1 0 0 1 0 00 4A
1 1 0 1 0 0 0 0 00 0B 1 1 0 1 0 0 1 0 00 4B
0 0 1 1 0 0 0 0 00 0C 0 0 1 1 0 0 1 0 00 4C
1 0 1 1 0 0 0 0 00 0D 1 0 1 1 0 0 1 0 00 4D
0 1 1 1 0 0 0 0 00 0E 0 1 1 1 0 0 1 0 00 4E
1 1 1 1 0 0 0 0 00 0F 1 1 1 1 0 0 1 0 00 4F
0 0 0 0 1 0 0 0 00 10 0 0 0 0 1 0 1 0 00 50
1 0 0 0 1 0 0 0 00 11 1 0 0 0 1 0 1 0 00 51
0 1 0 0 1 0 0 0 00 12 0 1 0 0 1 0 1 0 00 52
1 1 0 0 1 0 0 0 00 13 1 1 0 0 1 0 1 0 00 53
0 0 1 0 1 0 0 0 00 14 0 0 1 0 1 0 1 0 00 54
1 0 1 0 1 0 0 0 00 15 1 0 1 0 1 0 1 0 00 55
0 1 1 0 1 0 0 0 00 16 0 1 1 0 1 0 1 0 00 56
1 1 1 0 1 0 0 0 00 17 1 1 1 0 1 0 1 0 00 57
0 0 0 1 1 0 0 0 00 18 0 0 0 1 1 0 1 0 00 58
1 0 0 1 1 0 0 0 00 19 1 0 0 1 1 0 1 0 00 59
0 1 0 1 1 0 0 0 00 1A 0 1 0 1 1 0 1 0 00 5A
1 1 0 1 1 0 0 0 00 1B 1 1 0 1 1 0 1 0 00 5B
0 0 1 1 1 0 0 0 00 1C 0 0 1 1 1 0 1 0 00 5C
1 0 1 1 1 0 0 0 00 1D 1 0 1 1 1 0 1 0 00 5D
0 1 1 1 1 0 0 0 00 1E 0 1 1 1 1 0 1 0 00 5E
1 1 1 1 1 0 0 0 00 1F 1 1 1 1 1 0 1 0 00 5F
0 0 0 0 0 1 0 0 00 20 0 0 0 0 0 1 1 0 00 60
1 0 0 0 0 1 0 0 00 21 1 0 0 0 0 1 1 0 00 61
0 1 0 0 0 1 0 0 00 22 0 1 0 0 0 1 1 0 00 62
1 1 0 0 0 1 0 0 00 23 1 1 0 0 0 1 1 0 00 63
0 0 1 0 0 1 0 0 00 24 0 0 1 0 0 1 1 0 00 64
1 0 1 0 0 1 0 0 00 25 1 0 1 0 0 1 1 0 00 65
0 1 1 0 0 1 0 0 00 26 0 1 1 0 0 1 1 0 00 66
1 1 1 0 0 1 0 0 00 27 1 1 1 0 0 1 1 0 00 67
0 0 0 1 0 1 0 0 00 28 0 0 0 1 0 1 1 0 00 68
1 0 0 1 0 1 0 0 00 29 1 0 0 1 0 1 1 0 00 69
0 1 0 1 0 1 0 0 00 2A 0 1 0 1 0 1 1 0 00 6A
1 1 0 1 0 1 0 0 00 2B 1 1 0 1 0 1 1 0 00 6B
0 0 1 1 0 1 0 0 00 2C 0 0 1 1 0 1 1 0 00 6C
1 0 1 1 0 1 0 0 00 2D 1 0 1 1 0 1 1 0 00 6D
0 1 1 1 0 1 0 0 00 2E 0 1 1 1 0 1 1 0 00 6E
1 1 1 1 0 1 0 0 00 2F 1 1 1 1 0 1 1 0 00 6F
0 0 0 0 1 1 0 0 00 30 0 0 0 0 1 1 1 0 00 70
1 0 0 0 1 1 0 0 00 31 1 0 0 0 1 1 1 0 00 71
0 1 0 0 1 1 0 0 00 32 0 1 0 0 1 1 1 0 00 72
1 1 0 0 1 1 0 0 00 33 1 1 0 0 1 1 1 0 00 73
0 0 1 0 1 1 0 0 00 34 0 0 1 0 1 1 1 0 00 74
1 0 1 0 1 1 0 0 00 35 1 0 1 0 1 1 1 0 00 75
0 1 1 0 1 1 0 0 00 36 0 1 1 0 1 1 1 0 00 76
1 1 1 0 1 1 0 0 00 37 1 1 1 0 1 1 1 0 00 77
0 0 0 1 1 1 0 0 00 38 0 0 0 1 1 1 1 0 00 78
1 0 0 1 1 1 0 0 00 39 1 0 0 1 1 1 1 0 00 79
0 1 0 1 1 1 0 0 00 3A 0 1 0 1 1 1 1 0 00 7A
1 1 0 1 1 1 0 0 00 3B 1 1 0 1 1 1 1 0 00 7B
0 0 1 1 1 1 0 0 00 3C 0 0 1 1 1 1 1 0 00 7C
1 0 1 1 1 1 0 0 00 3D 1 0 1 1 1 1 1 0 00 7D
0 1 1 1 1 1 0 0 00 3E 0 1 1 1 1 1 1 0 00 7E
1 1 1 1 1 1 0 0 00 3F 1 1 1 1 1 1 1 0 00 7F
OCH712C 41
Indoor unit only operation
In indoor unit only operation, operation without connecting outdoor unit is possible. Indoor unit only operation
During Indoor unit only operation, the main control has control functions. Indoor unit Necessary
Heat pump Not necessary
<Heater> Main remote controller Necessary
Heating for DHW and space heating is provided by the heater. DIP switch setting Electric heater
• Activating indoor unit only operation mode SW4-4 ON, SW4-5 ON
To activate indoor unit only operation, see the following:
Boiler
1. Switch OFF the breaker for the outdoor unit (or both breakers if hydrobox is powered independently).
SW4-4 ON, SW4-6 ON
2. Change DIP switch SW4-4 and SW4-5 to ON.
3. Switch ON the breaker(s). Setting range for flow temp. 20 to 60°C Selectable
4. Indoor unit only operation is now activated. Setting range for tank temp. 40 to 60°C Selectable
• Deactivating indoor unit only operation mode

To deactivate indoor unit only operation, see the following:
2. Change DIP switch SW4-4 and SW4-5 to OFF.
3. Switch ON the breaker(s).
4. Indoor unit only operation is now deactivated.
<Boiler>
Heating for space heating is provided by the boiler.
• Activating indoor unit only operation mode
To activate indoor unit only operation, see the following:
2. Change DIP switch SW4-4 and SW4-6 to ON.
4. Indoor unit only operation is now activated.
• Deactivating indoor unit only operation mode

To deactivate indoor unit only operation, see the following:
2. Change DIP switch SW4-4 and SW4-6 to OFF.
4. Indoor unit only operation is now deactivated.
Emergency operation Emergency operation

In emergency operation, operation without connecting outdoor unit and main remote controller is pos- Indoor unit Necessary
sible.
Heat pump Not necessary
During Emergency operation, the main control has NO control functions.
Space heating flow temp. is restarted 40°C and DHW tank temp. is restricted 50°C. *1 Main remote controller Not necessary
DIP switch setting Electric heater
<Heater> SW4-5 ON
Heating for DHW and space heating is provided by the heater. Boiler
• Activating emergency operation mode SW4-6 ON
To activate emergency operation, see the following: Setting range for flow temp. Fixed at 40°C
1. Switch OFF the breaker for the outdoor unit (or both breakers if hydrobox is powered independently). Setting range for tank temp. Fixed at 50°C *1
2. Change DIP switch SW4-5 to ON.
3. Switch ON the breaker(s). *1 D
efault setting is 50°C. Once system has started running,
4. Emergency operation is now activated. emergency operation runs at the latest set temp.
• Deactivating emergency operation mode

To deactivate emergency operation, see the following:
2. Change DIP switch SW4-5 to OFF.
4. Emergency operation is now deactivated.
<Boiler>
Heating for space heating is provided by the boiler.
• Activating emergency operation mode
To activate emergency operation, see the following:
2. Change DIP switch SW4-6 to ON.
4. Emergency operation is now activated.
• Deactivating emergency operation mode

To deactivate emergency operation, see the following:
2. Change DIP switch SW4-6 to OFF.
4. Emergency operation is now deactivated.
WARNING
Do not attempt to change the DIP switches whilst the breaker(s) are ON as this could result in electric shock.
OCH712C 42
10 TROUBLESHOOTING
10-1. Troubleshooting
<Summary of self diagnosis based on check codes and Service Procedures>
Present and past check codes are logged, and they can be displayed on the main remote controller or control board of the outdoor unit.
Please refer to the table below and subsequent explanations to diagnose and remedy typical problems that may occur in the field.
Unit Condition Check code Action

Reoccurring problem Displayed Use table "10-4.Self diagnosis and action" to identify fault and correct.
Not Displayed Use table "10-5. Troubleshooting by inferior phenomena" to identify fault and correct.
Non reoccurring problem Logged 1. Check temporary causes of defects such as the operation of safety devices on the refrigerant/water
circuit including compressor, poor wiring, electrical noise, etc. Re-check the symptom and the instal-
lation environment, refrigerant amount (Split systems only), weather conditions at time of fault, etc.
2. Reset check code logs, Service the unit and restart system.
Not Logged 1. Recheck the abnormal symptom.
2. Identify cause of problem and take corrective action according to Table "10-5. Troubleshooting by
inferior phenomena".
3. If no obvious problem can be found, continue to operate the unit.
Note:
Electrical components should only be replaced as a final option. Please follow instructions in "10-4. Self diagnosis and action" and "10-5. Trouble-
shooting by inferior phenomena" fully before resorting to replacing parts.
10-2. Test Run

Before a test run
• After installation of outdoor unit, pipework and electrical wiring, recheck that there is no water leakage, loosened connections or miswiring.
• Measure impedance between the ground and the power supply terminal block (L,N) on the outdoor and indoor units with suitable (500 V) ohmmeter. Resistance
should be ≥ 1.0 MΩ .
• Read the Installation and Operation Manuals fully especially the safety requirements before carrying out any test runs.
10-3. Malfunction diagnosis method by main remote controller

If a malfunction occurs during start up or operation, the check code screen may be displayed on the main remote controller.
The check code screen shows the following; code, unit, ref. address, and telephone number of installer (only if previously entered by the installer)
Please note in the case of some malfunctions an check code is not generated, please refer to table "10-5. Troubleshooting by inferior phenomena" for more details.
To reset
1. To reset the main remote controller press F4 button (Reset).
2. Then press F3 (Yes) to confirm.
OCH712C 43
10-4. Self diagnosis and action
Check if DIP SW is set correctly. (Refer to "6-6. DIP switch functions".)
Check code Title and display conditions Possible Cause Diagnosis and action
L3 Circulation water temperature overheat 1. Insufficient system head 1. Refer to table in "10-6. Checking Compo-
protection nent Parts' Function" to determine if system
<DHW/Heating/Cooling/LP/FS/OS> pump meets requirements.
Check code displayed when THW1 detects a If more head required either add a pump of
temp. ≥ 80ºC for 10 consecutive seconds or the same size or replace existing pump with
THW2 detects a temp. ≥ 80ºC for 10 consecutive capacity model.
seconds. See "11. DISASSEMBLY PROCEDURE" for
how to replace pump.
2. Reduced flow in primary water circuit 2. Check circulation pump (See "10-6. Check-
DHW : Domestic hot water mode Due to 1 or more of the following; ing Component Parts' Function" for how to
Heating : Heating mode Faulty pump, insufficient air purge, check).
Cooling : Cooling mode blocked strainer, leak in water circuit Open purge valve to remove trapped air.
LP : Legionella prevention mode Check the strainer for blockages.
FS : Freeze stat Check the primary water circuit for leaks.
OS : Operation stop Check that the flow amount is within the
TH1A/B : Room temperature thermistor recommended range.
TH2 : Refrigerant liquid temperature thermistor 3. Valve operation fault 3. Check valves on primary water circuit are
THW1 : Flow water temperature thermistor installed level.
THW2 : Return water temperature thermistor 4. 2-way valve (local supply) actuator 4. Electrically test to determine fault.
THW5A/B : DHW tank water temperature thermistor fault
THW6 : Zone1 flow temperature thermistor
5. 3-way valve (local supply) actuator 5. 1) Electrically test to determine fault.
THW7 : Zone1 return temperature thermistor
fault 2) Operate 3-way valve manually using the
THW8 : Zone2 flow temperature thermistor
main remote controller. (Refer to <Manual
THW9 : Zone2 return temperature thermistor
operation> in "9-4. Service Menu".)
THWB1 : Boiler flow temperature thermistor
3) Replace 3-way valve.
6. Booster heater relay (BHC1, BHC2, 6. Electrically test the relays (BHC1, BHC2,
BHCP) operating fault BHCP) to determine fault.
See "10-6. Checking Component Parts'
Function" for how to check.
7. Power supply voltage increase 7. Check the supply voltage.
8. THW1 or THW5B has become de- 8. Visually inspect location and reattach as
tached from its holder. necessary.
9. THW1 or THW2 fault 9. Check resistance of thermistor against table
in "10-6. Checking Component Parts' Func-
tion".
Compare FTC detected temperature to
hand held detector.
10. FTC board failure 10. Replace board.
L4 Tank water temperature overheat protection 1. 3-way valve (local supply) actuator 1. 1) Electrically test to determine fault.
<DHW/Heating/Cooling/LP/FS/OS> fault 2) Operate 3-way valve manually using the
Check code display when THW5B detects a main remote controller. (Refer to <Manual
temp. ≥ 75ºC for 10 consecutive seconds. operation> in "9-4. Service Menu".)
2. Immersion heater relay (IHC) operat- 2. Check immersion heater relay (IHC).
ing fault
3. THW5B fault 3. Check resistance of thermistor against table
tion".
hand held detector.
OCH712C 44
P1/P2/L5/LD Indoor unit temperature thermistor failure 1. Connector/terminal wire has become 1. Visually check the terminals and connec-
Note: The thermistors subject to failure can be detached or loose wiring. tions and reattaches appropriate.
checked in “Request code: 567” in “Running 2. Thermistor fault 2. Check resistance of thermistor against
information. table in "10-6. Checking Component Parts'
Function".
<DHW/Heating/Cooling/LP/FS/OS> Compare FTC detected temperature to
Check code displayed when thermistor is at open hand held detector.
or short (see table). 3. FTC board failure 3. Replace board.
4. The thermistor on the wireless remote 4. Replace wireless remote controller or main
Exceptions
controller or the main remote controller remote controller.
Check code will not be displayed for TH2; During
may be defective. (when Room temp.
defrost and for 10 minutes after defrost operation.
is chosen for the Heating operation
and when Main remote controller or
Room RC 1-8 is chosen for the Room
Sensor setting in the Initial setting)
5. Incorrect setting of the DIP switch(es) 5. Check the DIP switch setting(s).
Thermistor
Check code Open detection Short detection
Symbol Name
P1 TH1A/TH1B Room temperature thermistor −39ºC or below 88.5ºC or above
P2 TH2 Liquid temperature thermistor −39ºC or below 88.5ºC or above
THW1 Flow water temperature thermistor −39ºC or below 88.5ºC or above
THW2 Return water temperature thermistor −39ºC or below 88.5ºC or above
THW5A DHW tank water temperature thermistor (upper) −39ºC or below 88.5ºC or above
THW5B DHW tank water temperature thermistor (lower) −39ºC or below 88.5ºC or above
L5
THW6 Zone1 flow temperature thermistor −39ºC or below 88.5ºC or above
THW7 Zone1 return temperature thermistor −39ºC or below 88.5ºC or above
THW8 Zone2 flow temperature thermistor −39ºC or below 88.5ºC or above
THW9 Zone2 return temperature thermistor −39ºC or below 88.5ºC or above
LD THWB1 Boiler flow temperature thermistor −40ºC or below 140ºC or above
L6 Circulation water freeze protection 1. Insufficient system head 1. Refer to table in "10-6. Checking Compo-
<DHW/Heating/Cooling/LP/FS/OS> nent Parts' Function" to determine if system
Check code displayed when THW1 detects pump meets requirements.
a temp. ≤ 1ºC for 10 consecutive seconds or If more head required either add a pump of
THW2 detects a temp. ≤ 3ºC for 10 consecutive the same size or replace existing pump with
seconds. capacity model.
See "11. DISASSEMBLY PROCEDURE" for
Exception how to replace pump.
Check code will not be displayed if; 2. Reduced flow in primary water circuit. 2. Check circulation pump (See "10-6. Check-
FS function is disabled, Due to 1 or more of the following; ing Component Parts' Function" for how to
For 10 minutes after water circulation pump1 is Faulty pump, insufficient air purge, check).
switched on. blocked strainer, leak in water circuit Open purge valve to remove trapped air.
Check the strainer for blockages.
Check the primary water circuit for leaks.
Check that the flow amount is within the
recommended range.
3. Valve operation fault 3. Check valves on primary water circuit are
installed level.
4. 2-way valve (local supply) actuator fault 4. Electrically test to determine fault.
5. 3-way valve (local supply) actuator fault 5. 1) Electrically test to determine fault.
2) Operate 3-way valve manually using the
main remote controller. (Refer to <Manual
operation> in "9-4. Service Menu".)
6. THW1 has become detached from its 6. Visually inspect location and reattach as
holder. necessary.
7. THW1 or THW2 fault 7. Check resistance of thermistor against table
tion".
hand held detector.
OCH712C 45
L8 Heating operation error 1. THW1 has become detached from its 1. Visually inspect location and reattach as
Note: “3” is displayed in “Request code: 567” in holder. necessary.
“Running information”. 2. Booster heater fault 2. Electrically test to determine fault.
<Heating/FS> See "10-6. Checking Component Parts'
If a), b) and c) occur, L8 is displayed; Function" for how to check.
a) N o change on THW1 and THW5B 3. THW1 or THW2 or THW5B fault 3. Check resistance of thermistor against
(under 1°C for 20 minutes from unit starts table in "10-6. Checking Component Parts'
operation) Function".
b) No change on THW1 Compare FTC detected temperature to
(under 1°C for 10 minutes from booster heater hand held detector.
starts operation)
c) THW1−THW2 < −5°C
(for 10 minutes continuously)
Heating operation error 1. THW6 has become detached from its 1. Visually inspect location and reattach as
Note: “ A” is displayed in “Request code: 567” in holder. necessary.
“Running information”. 2. THW6 or THW7 fault 2. Check resistance of thermistor against
table in "10-6. Checking Component Parts'
Function".
hand held detector.
Heating operation error 1. THW8 has become detached from its 1. Visually inspect location and reattach as
Note: “ C” is displayed in “Request code: 567” in holder. necessary.
“Running information”. 2. THW8 or THW9 fault 2. Check resistance of thermistor against
table in "10-6. Checking Component Parts'
Function".
hand held detector.
L9 Low primary circuit (Heat source side) flow 1. Insufficient system head 1. Refer to table in "10-6. Checking Com-
rate detected by flow sensor ponent Parts' Function" to determine if
Note: “1” is displayed in “Request code: 569” in system pump meets requirements.
“Running information”. If more head required either add a pump
<DHW/Heating/Cooling/LP/FS> of the same size or replace existing pump
Check code displayed when flow sensor detects with capacity model.
low flow rate for 10 seconds. See "11. DISASSEMBLY PROCEDURE"
for how to replace pump.
Exception 2. Reduced flow in primary water circuit 2. Check circulation pump (See "10-6.
For 1 minute after water circulation pump1 is Due to 1 or more of the following; Checking Component Parts' Function" for
Faulty pump, insufficient air purge, how to check).
switched on.
blocked strainer, leak in water circuit Open purge valve to remove trapped air.
recommended range.
3. Valve operation fault 3. Check valves on primary water circuit are
installed level.
4. 2-way valve (local supply) actuator fault 4. Electrically test to determine fault.
5. Connector wire has become detached 5. Visually check the CN1A connector and
or loose wiring. reattach if necessary.
6. Flow sensor fault 6. Electrically test to determine fault.
7. Incorrect setting of the SW2-2 7. Check the SW2-2 setting.
Low primary circuit (Zone1 side) flow rate 1. Insufficient system head 1. If more head required either add a pump
detected by flow switch of the same size or replace existing pump.
Note: “2” is displayed in “Request code: 569” in 2. Reduced flow in primary water circuit 2. Check circulation pump (See "10-6.
“Running information”. Due to 1 or more of the following; Checking Component Parts' Function" for
Faulty pump, insufficient air purge, how to check).
recommended range.
3. Terminal wire has become detached 3. Visually check the IN3 terminal and reat-
or loose wiring. tach if necessary.
4. Flow switch fault 4. Electrically test to determine fault.
OCH712C 46
L9 Low primary circuit (Zone2 side) flow rate 1. Insufficient system head 1. If more head required either add a pump of
detected by flow switch the same size or replace existing pump.
Note: “3” is displayed in “Request code: 569” in 2. Reduced flow in primary water circuit 2. Check circulation pump (See "10-6. Check-
“Running information”. Due to 1 or more of the following; ing Component Parts' Function" for how to
Faulty pump, insufficient air purge, check).
recommended range.
3. Terminal wire has become detached or 3. Visually check the IN7 terminal and reat-
loose wiring. tach if necessary.
4. Flow switch fault 4. Electrically test to determine fault.
LA Pressure sensor failure 1. Connector/terminal wire has become 1. Check pressure sensor cable for damage or
detached or loose wiring. loose connections.
2. Pressure sensor fault 2. Electrically test to determine fault.
LB High pressure protection 1. Flow rate of the heating circuit may be 1. Check water circuit.
reduced.
2. Plate heat exchanger may be clogged. 2. Check the plate heat exchanger.
3. Outdoor unit failure 3. Refer to outdoor unit service manual.
LC Boiler circulation water temperature overheat 1. The set temperature for Boiler is too 1. Check if the set temperature for Boiler for
protection high. heating exceeds the restriction. (See the
<DHW/Heating/LP/FS/OS> manual for the thermistors "PAC-TH011HT-E")
Check code displayed when THWB1 detects a 2. Flow rate of the heating circuit from the 2. Check for
temperature ≥80ºC for 10 consecutive seconds boiler may be reduced. • water leakage
• strainer blockage
• water circulation pump function
LD Boiler temperature thermistor (THWB1) failure Refer to check codes (P1/P2/L5/LD).
LE Boiler operation error 1. THW6 has become detached from its 1. Visually inspect location and reattach as
<Heating> holder. necessary.
Boiler is running and THW6 detects a 2. Incorrect wiring between FTC (OUT10) 2. See the manual of the thermistors "PAC-
temperature <30ºC for consecutive 60 minutes. and the boiler TH011HT-E".
3. Boiler fuel has run out or the system is 3. Check the status of the boiler.
OFF.
4. Boiler failure 4. Check the status of the boiler.
LF Flow sensor failure Disconnection or loose connection of Check flow sensor cable for damage or
flow sensor loose connections.
LH Boiler circulation water freeze protection Flow rate of the heating circuit from the Check for
boiler may be reduced. • water leakage
• strainer blockage
• water circulation pump function
LJ DHW operation error (type of external plate HEX) 1. DHW tank water temp. thermistor 1. Check for disconnection of DHW tank water
(THW5B) has become detached from temp. thermistor (THW5B).
its holder.
2. Flow rate of the sanitary circuit may be 2. Check for water circulation pump function.
reduced.
LL Setting errors of DIP switches on FTC control Incorrect setting of DIP switches
board 1. Boiler operation 1. For boiler operation, check that DIP SW1-1
is set to ON (With Boiler) and DIP SW2-6 is
set to ON (With Mixing Tank).
2. 2-zone temperature control 2. For 2-zone temperature control, check DIP
SW2-7 is set to ON (2-zone) and DIP SW2-
6 is set to ON (With Mixing Tank).
3. Multiple outdoor units control 3. For multiple outdoor units control, check DIP
SW1-3 is set to ON on FTC (sub) that runs
DHW operation .
P1 Indoor unit temperature thermistor (TH1A/TH1B) Refer to check codes (P1/P2/L5/LD).
failure
P2 Indoor unit temperature thermistor (TH2) failure Refer to check codes (P1/P2/L5/LD).
OCH712C 47
P6 Anti-freeze protection of plate heat exchanger <Cooling>
<Cooling> 1. Reduced water flow 1., 2. Check water piping.
The check code displayed when Ref. liquid temp. • Clogged filter
(TH2) stays at −5ºC or lower for 10 seconds after • Leakage of water
compressor operates for 6 minutes. 2. Low temperature
• Low load
• Inlet water is too cold.
3. Defective water pump 3. Check water pump.
4. Defective outdoor fan control 4. Check outdoor fan motor.
5. Overcharge of refrigerant 5., 6. Check operating condition of refrigerant circuit.
6. Defective refrigerant circuit (clogs)
7. Malfunction of linear expansion valve 7. Check linear expansion valve.
<Defrosting> <Defrosting>
THW2 detects a temperature ≤15ºC and TH2 1. Reduced water flow 1., 2. Check water piping.
detects a temperature ≤−16ºC for consecutive 10 • Clogged filter
seconds. • Leakage of water
2. Low temperature
• Low load
• Inlet water is cold.
3. Defective water pump 3. Check water pump.
4. Leakage or shortage of refrigerant 4. Correct to proper amount of refrigerant.
5. Malfunction of linear expansion valve 5. Check linear expansion valve.
E0/E4 Main remote controller communication failure 1. Contact failure with transmission cable 1. Check connection cable for damage or
(Reception error) loose connections at the FTC and main
Check code E0 is displayed if main remote con- remote controller terminals.
troller does not receive any signal from the indoor 2. Wiring procedure not observed. 2. Check main remote controller and FTC
unit for ref. address "0" for 3 minutes. (Cable length/cable diameter/number common wiring max cable length 500 m.
Check code E4 is displayed if indoor unit does of indoor units/number of main remote Only use 2-core cable.
not receive any data from the main remote controllers) Only connect 1 main remote controller to 1
controller for 3 minutes or indoor unit does not re- FTC indoor unit board.
ceive any signal from the main remote controller 3. Fault on the indoor unit FTC board 3. to 5.
for 2 minutes. section controlling Ref. address "0" If the problem is not solved by the above
4. Fault with the main remote controller measures then:
circuit board Turn the power to the indoor unit OFF and
5. Electrical noise causes interference then ON.
with transmission/reception of data for Power to both the indoor unit and outdoor
main remote controller. units should be switched OFF then ON. (This
may require switching 1 or 2 breakers de-
pending if the unit is powered independently
from the outdoor unit).
If the E4 code is still displayed the FTC and/
or the main remote controller circuit board
should be replaced.
E3/E5 Main remote controller communication failure 1. 2 or more main remote controllers have 1. Only connect 1 main remote controller to 1
(Transmission error) been connected to the FTC. FTC indoor unit board.
Check code E3 is displayed if the main remote 2. Fault with main remote controller 2. to 4.
controller cannot find an empty transmission transmission/receiving circuit board Turn the power to the indoor unit OFF and
path and thus fails to transmit for 6 seconds or 3. Fault with the main remote controller then ON.
the data received by the main remote controller circuit board Power to both the indoor unit and outdoor
is different to what was sent (by the main remote units should be switched OFF then ON.
4. Electrical noise causes interference
controller) 30 consecutive times. (This may require switching 1 or 2 breakers
with transmission/reception of data for
Check code E5 is displayed if the FTC cannot main remote controller. depending if the unit is powered indepen-
find an empty transmission path for 3 minutes dently from the outdoor unit).
and thus cannot transmit or the data sent by the If the E3/E5 code is still displayed the FTC
FTC is different to what was expected 30 consec- and/or the main remote controller circuit
utive times. board should be replaced.
E6 Indoor/outdoor communication failure Note:
(Reception error) Check the LED display on the outdoor unit
Check code E6 is displayed if after the power is circuit board.
switched ON to the indoor unit, the FTC board (Connect the A-control service tool, PAC-
does not receive any signal or the signal received SK52ST to test.) Refer to the outdoor unit ser-
is not complete for 6 minutes, or after a period of vice manual for explanation of EA-EC codes.
operation the FTC board does not receive any 1. Contact failure/short circuit/miswiring 1. Check the connections on the indoor and
signal or the signal received is not complete for 3 outdoor units have not become loose and
minutes. that the connecting cable is not damaged.
2. Fault with outdoor unit transmission/ 2. to 4.
receiving circuit board Turn the power to the indoor unit OFF and
3. Fault with FTC transmission/receiving then ON.
circuit board Power to both the indoor unit and outdoor
4. Electrical noise causes interference units should be switched OFF then ON.
with FTC-Outdoor unit transmission (This may require switching 1 or 2 breakers
cable. depending if the unit is powered indepen-
dently from the outdoor unit).
If the E6 code is still displayed the FTC
and/or the outdoor unit circuit board should
be replaced.
OCH712C 48
E7 Indoor/outdoor communication failure 1. Fault with FTC transmission/receiving 1. to 3.
(Transmission error) circuit board Turn the power to the indoor unit OFF and
Check code E7 is displayed if signal "1" is 2. Electrical noise causes interference then ON.
received 30 consecutive times despite the FTC with power supply. Power to both the indoor unit and outdoor
board sending signal "0". units should be switched OFF then ON.
3. Electrical noise causes interference
with FTC-outdoor unit transmission (This may require switching 1 or 2 breakers
cable. depending if the unit is powered indepen-
If the E7 code is still displayed the FTC
circuit board should be replaced.
E1/E2 Main remote controller control board failure 1. Fault with the main remote controller 1. Replace main remote controller circuit
Check code E1 displayed if main remote control- circuit board board.
ler cannot access it is non-volatile (non power
dependent) memory.
Check code E2 is displayed when there is a fault
with the main remote controller's internal clock.
J0 Indoor unit/wireless receiver communication 1. Connection fault with wireless receiver- 1. Check the connections to the wireless re-
failure FTC connection ceiver and FTC have not become loose and
Check code J0 is displayed when the FTC can- that the connecting cable is not damaged.
not receive data from the wireless receiver for 1 2. Fault with FTC receiving circuit board 2. to 4.
minute. 3. Fault with wireless receiver's transmis- Turn the power to the indoor unit OFF and
sion circuit board then ON.
4. Electrical noise causes interference Power to both the indoor unit and outdoor
with wireless receiver communication units should be switched OFF then ON.
cable. (This may require switching 1 or 2 breakers
depending if the unit is powered indepen-
If the J0 code is still displayed, the FTC
and/or the wireless receiver circuit board
should be replaced.
J1 to J8 Wireless remote controller/wireless receiver 1. Battery on wireless remote control may 1. Check and replace the battery on wireless
communication failure be flat. remote control if necessary.
(Reception error) 2. The wireless remote controller is out of 2. to 4.
Check code displayed if wireless receiver range of the wireless receiver. Reposition the wireless remote control
receives no/incomplete data from the wireless closer to the receiver and perform a
3. Fault with wireless remote controller
remote controller for 15 consecutive minutes. communication test.
transmission circuit board
4. Fault with wireless receiver's reception For procedure, refer to wireless remote
The digit after the J refers to the address of the controller installation manual.
wireless remote controller that has the error. circuit board
If "OK" is displayed, then the cause of the
E.g. Check code "J3" refers to a communication J1 to J8 error was the controller was out of
fault between the wireless receiver and wireless range of the receiver.
remote control with address 3. The wireless remote controller should be
installed within range of the receiver.
If "Err" is displayed, replace wireless remote
controller with a new controller and perform
the pairing procedure.
If the "Err" code is still displayed after this
procedure, the fault is with the receiver unit
(attached to the indoor unit).
The receiver unit should be replaced with
a new part and the original remote control
can be reconnected.
If "OK" is displayed, then the fault is with
the remote control and this should be
replaced.
J9 Main remote controller communication failure Refer to check codes. (E0 and E4)
Check code J9 is displayed when signal is not
received normally from FTC (sub) for 3 minutes.
EE Combination error between FTC and outdoor unit R410A outdoor unit is combined incorrectly. Check combination of FTC and outdoor unit.
U*, F*, A* Outdoor unit failure Outdoor unit failure Refer to outdoor unit service manual.
Note: To cancel check codes please switch system off (press button F4 (RESET) on main remote controller).
OCH712C 49
10-5. Troubleshooting by inferior phenomena
No. Fault symptom Possible cause Explanation - Solution
1 Main remote controller 1. There is no power supply to main remote 1. Check LED2 on FTC. (See "6. WIRING DIAGRAM".)
display is blank. controller. (i) When LED2 is lit.
Check for damage or contact failure of the main remote controller wiring.
(ii) When LED2 is blinking.
Refer to No. 5 below.
(iii) When LED2 is not lit.
Refer to No. 4 below.
2. Power is supplied to main remote 2. Check the following:
controller, however, the display on the • D isconnection between the main remote controller cable and the FTC
main remote controller does not appear. control board
• Failure of the main remote controller if “Please Wait” is not displayed.
• Refer to No. 2 below if “Please Wait” is displayed.
2 “Please Wait” remains 1. "Please Wait" is displayed for up to 6 1. Normal operation, no action necessary.
displayed on the main minutes.
remote controller. 2. Communication failure between the main 2.,3. Main remote controller start up checks/procedure
remote controller and FTC (i) If “0%” or “50 to 99%” is displayed below "Please Wait" there is a
3. Communication failure between FTC and communication error between the main remote controller and the FTC
outdoor unit control board.
• Check wiring connections on the main remote controller.
• Replace the main remote controller or the FTC control board.
(ii) If “1 to 49%” is displayed there is a communication error between the
outdoor unit's and FTC's control boards.
• Check the wiring connections on the outdoor unit control board and the FTC
control board.
(Ensure S1 and S2 are not cross-wired and S3 is securely wired with no
damage. See "7. FIELD WIRING".)
• Replace the outdoor unit's and/or the FTC's control boards.
3 The main screen The main remote controller operations do Normal operation, no action necessary.
appears with a press not work for a while after the settings are The indoor unit is applying updated settings made in the service menu. Normal
of the “ON” button, but changed in the service menu. This is because operation will start shortly.
disappears in a second. the system takes time to apply the changes.
4 LED2 on FTC is off. When LED1 on FTC is also off. (See "6.
(See "6. WIRING WIRING DIAGRAM".)
DIAGRAM".) <FTC powered via outdoor unit.>
1. The outdoor unit is not supplied at the 1. Check the voltage across the terminals L and N or L3 and N on the outdoor
rated voltage. power board. (See "7. FIELD WIRING".)
• When the voltage is not 220 to 240 VAC, check wiring of the outdoor unit
and of the breaker.
• When the voltage is at 220 to 240 VAC, go to “2.” below.
2. Defective outdoor controller circuit board 2. Check the voltage across the outdoor unit terminals S1 and S2. (See "7.
FIELD WIRING".)
• When the voltage is not 220 to 240 VAC, check the fuse on the outdoor
control board and check for faulty wiring.
• When the voltage is 220 to 240 VAC, go to “3.” below.
3. FTC is not supplied with 220 to 240 VAC. 3. Check the voltage across the indoor unit terminals S1 and S2. (See "7. FIELD
WIRING".)
• When the voltage is not 220 to 240 VAC, check FTC-outdoor unit wiring for
faults.
• When the voltage is 220 to 240 VAC, go to “4.” below.
4. FTC failure 4. Check the FTC control board.
• Check the fuse on FTC control board.
• Check for faulty wiring.
• If no problem found with the wiring, the FTC control board is faulty.
5. Faulty connector wiring 5. Check the connector wiring.
• When the connectors are wired incorrectly, re-wire the connectors referring
to below. (See "7. FIELD WIRING".)
L
YELLOW BLACK
YELLOW BLACK
N
Initial settings
(Power supplied CN01
CN01
by outdoor unit) White

S1
S2
Hydrobox
S3
control board
OCH712C 50
4 LED2 on FTC is off. <FTC powered on independent source>
(See "6. WIRING 1. FTC is not supplied with 220 to 240 VAC. 1. Check the voltage across the L and N terminals on the indoor power supply
DIAGRAM".) terminal block. (See "7. FIELD WIRING".)
• When the voltage is not 220 to 240 VAC, check for faulty wiring to power
supply.
• When the voltage is 220 to 240 VAC, go to 2. below.
2. There are problems in the method of 2. Check for faulty wiring between the connectors.
connecting the connectors. • When the connectors are wired incorrectly re-wire them correctly referring
to below. (See "7. FIELD WIRING". and a wiring diagram on the control
and electrical box cover.)
BLACK YELLOW
YELLOW BLACK
L
N
Modified settings White
(Separate power CN01
CN01
supply to S1 Hydrobox
control board
the hydrobox) S2
S3
• If no problem found with the wiring, go to 3. below.

3. FTC failure 3. Check the FTC control board.
• Check the fuse on FTC control board.
When LED1 on FTC is lit: Recheck the refrigerant address setting on the outdoor unit.
Incorrect setting of refrigerant address for Set the refrigerant address to “0”.
outdoor unit (Set refrigerant address using SW1(3–6) on outdoor controller circuit board.)
(None of the refrigerant address is set to "0".)
5 LED2 on FTC is When LED1 is also blinking on FTC: Check for faulty wiring between FTC and outdoor unit.
blinking. Faulty wiring between FTC and outdoor unit
(See "6. WIRING When LED1 on FTC is lit:
DIAGRAM".) 1. Faulty wiring in main remote controller 1. Check for faulty wiring in main remote controller.
Multiple indoor units have been wired to a sin- The number of indoor units that can be wired to a single outdoor unit is one.
gle outdoor unit. Additional indoor units must be wired individually to a single outdoor unit.
2. Short-circuited wiring in main remote controller 2.,3. Remove main remote controller wires and check LED2 on FTC. (See Figure
5.2.1. in installation manual)
• If LED2 is blinking check for short circuits in the main remote controller wiring.
3. Main remote controller failure • If LED2 is lit, wire the main remote controller again and:
- if LED2 is blinking, the main remote controller is faulty;
- if LED2 is lit, faulty wiring of the main remote controller has been corrected.
6 LED4 on FTC is off. 1. SD memory card is NOT inserted into the 1. Correctly insert SD memory card in place until a click is heard.
(See "6. WIRING memory card slot with correct orientation.
DIAGRAM".) 2. Not an SD standards compliant memory card 2. Use an SD standards compliant memory card. (Refer to section 5.6 in instal-
lation manual)
LED4 on FTC is 1. Full of data 1. Move or delete data, or replace SD memory card with a new one.
blinking. 2. Write-protected 2. Release the write-protect switch.
(See "6. WIRING 3. NOT formatted 3. Refer to "5.6 Using SD memory card" in installation manual.
DIAGRAM".) 4. Formatted in NTFS file system 4. FTC is Not compatible with NTFS file system. Use an SD memory card for-
matted in FAT file system.
7 No water at hot tap. 1. Cold main off 1. Check and open stop cock.
2. Strainer (local supply) blocked 2. Isolate water supply and clean strainer.
8 Cold water at tap. 1. Hot water run out. 1. Ensure DHW mode is operating and wait for DHW tank to re-heat.
2. Prohibit, schedule timer or holiday mode se- 2. Check settings and change as appropriate.
lected or demand control input (IN4) or smart
grid ready (switch-off command).
3. Heat pump not working 3. Check heat pump – consult outdoor unit service manual.
4. Booster heater cut-out tripped. 4. Check booster heater thermostat and press reset button if safe.
Reset button is located on the side of booster heater, covered with white rub-
ber cap. See "4. PART NAMES AND FUNCTIONS" to find out its position.
5. The earth leakage circuit breaker for booster 5. Check the cause and reset if safe.
heater breaker (ECB1) tripped.
6. The booster heater thermal cut-out has tripped 6. Check resistance across the thermal cut-out, if open then the connection is
and cannot be reset using the manual reset broken and the booster heater will have to be replaced.
button. Contact your Mitsubishi Electric dealer.
7. Immersion heater cut-out tripped. 7. Check immersion heater thermostat and press reset button, located on im-
mersion heater boss, if safe. If the heater has been operated with no water
inside it may have failed, so please replace it with a new one.
8. Immersion heater breaker (ECB2) tripped. 8. Check the cause and reset if safe.
9. 3-way valve fault 9. Check plumbing/wiring to 3-way valve.
(i) M
anually override 3-way valve using the main remote controller. (Refer to
<Manual operation> in section "9-4. Service menu".) If the valve does not
still function, go to (ii) below.
(ii) Replace 3-way valve.
OCH712C 51
9 Water heating takes 1. Heat pump not working 1. Check heat pump – consult outdoor unit service manual.
longer. 2. Booster heater cut-out tripped. 2. Check booster heater thermostat and press reset button if safe.
ber cap. See "4. PART NAMES AND FUNCTIONS" to find out its position.
3. Booster heater breaker (ECB1) tripped. 3. Check the cause and reset if safe.
4. The booster heater thermal cut-out has 4. Check resistance across the thermal cut-out, if open then connection is
tripped and cannot be reset using the manual broken and the booster heater will have to be replaced.
reset button. Contact your Mitsubishi Electric dealer.
5. Immersion heater cut-out has been triggered. 5. Check immersion heater thermostat and press reset button if safe. If the
heater kept running with no water inside, this may have resulted in failure, so
replace it with a new one.
6. Immersion heater breaker (ECB2) tripped. 6. Check the cause and reset if safe.
10 Temperature of DHW When DHW operation is not running, the DHW
tank water dropped. tank emits heat and the water temperature
decreases to a certain level. If water in the DHW
tank is reheated frequently because of a signifi-
cant drop in water temperature, check for the
following.
1. Water leakage in the pipes that connect to the 1. Take the following measures.
DHW tank •R
etighten the nuts holding the pipes onto the DHW tank.
•R
eplace seal materials.
•R
eplace the pipes.
2. Insulation material coming loose or off 2. Fix insulation.
3. 3-way valve failure 3. Check plumbing/wiring to 3-way valve.
(i) M
anually override 3-way valve using the main remote controller. (Refer
to <Manual operation> in "9-4. Service Menu".) If the valve does not still
function, go to (ii) below.
(ii) Replace 3-way valve.
11 Hot or warm water Heat of hot water pipe is transferred to cold water Insulate/re-route pipework.
from cold tap. pipe.
12 Water leakage 1. Poorly sealed connections of water circuit 1. Tighten connections as required.
components
2. Water circuit components reaching the end of 2. Refer to PARTS CATALOG in the service manual for expected part lifetimes
life and replace them as necessary.
13 Heating system does 1. Prohibit, schedule timer or holiday mode se- 1. Check settings and change as appropriate.
not reach the set lected or demand control input (IN4) or smart
higher temperature. grid ready (switch-off command).
2. Check settings and change as appropriate. 2. Check the battery power and replace if flat.
3. The temperature sensor is located in a room 3. Relocate the temperature sensor to a more suitable room.
that has a different temperature relative to that
of the rest of the house.
4. Heat pump not working 4. Check heat pump – consult outdoor unit service manual.
5. Booster heater cut-out tripped. 5. Check booster heater thermostat and press reset button if safe.
ber cap. (See "4. PART NAMES AND FUNCTIONS" for position.)
6. Booster heater breaker (ECB1) tripped. 6. Check the cause of the trip and reset if safe.
7. The booster heater thermal cut-out tripped and 7. Check resistance across the thermal cut-out, if open then the connection is
cannot be reset using the manual reset button. broken and the booster heater will have to be replaced.
Contact your Mitsubishi Electric dealer.
8. Incorrectly sized heat emitter 8. Check the heat emitter surface area is adequate
Increase size if necessary.
9. 3-way valve failure 9. Check plumbing/wiring to 3-way valve.
10. Battery problem (*wireless control only) 10. Check the battery power and replace if flat.
11. If a mixing tank is installed, the flow rate 11. Increase the flow rate between the mixing tank and the hydrobox or
between the mixing tank and the hydrobox is decrease that between the mixing tank and the local system.
less than that between the mixing tank and
the local system.
14 Heating system does The heating system operates according to the Normal operation, no action necessary.
not reach the set heating pressure to prevent the low pressure
lower temperature. system from frequent switching (ON/OFF) of the
compressor.
OCH712C 52
15 In 2-zone tempera- 1. When Zone1 and Zone2 are both in heating 1. Normal operation, no action necessary.
ture control, only mode, the hot water temperature in Zone2
Zone2 does not does not exceed that in Zone1.
reach the set tem- 2. Faulty wiring of motorized mixing valve 2. Refer to "5.3 Wiring for 2-zone temperature control" in installation manual.
perature. 3. Faulty installation of motorized mixing valve 3. Check for correct installation. (Refer to the manual included with each motor-
ized mixing valve.)
4. Incorrect setting of Running time 4. Check for correct setting of Running time.
5. Motorized mixing valve failure 5. Inspect the mixing valve. (Refer to the manual included with each motorized
mixing valve.)
16 When a PUHZ- The outdoor unit is set to have operation of the Turn ON Electric heater (Heating) or Electric heater (DHW) using the main re-
FRP outdoor unit is indoor unit of air conditioner take precedence mote controller.
connected, DHW or over that of the hydrobox, and in the main remote
Heating operation controller settings "Electric heater (Heating)" or
cannot run. "Electric heater (DHW)" is turned off.
17 When a PUHZ-FRP When the outdoor unit is set to have cooling Normal operation, no action necessary.
outdoor unit is con- operation of the indoor unit of air conditioner take If Air-to-Water system is given priority in operation, comp Hz can be regulated
nected and is in heat precedence over that of the hydrobox, the outdoor depending on the load of DHW or Heating. For more details, refer to the PUHZ-
recovery operation, unit controls the frequency of the compressor FRP installation manual.
the set temperature according to the load of air conditioner. The DHW
is not reached. and heating run according to that frequency.
18 After DHW operation At the end of the DHW mode operation the 3-way Normal operation, no action necessary.
room temperature valve diverts hot water away from the DHW circuit
rises slightly. into space heating circuit.
This is done to prevent the hydrobox components
from overheating.
The amount of hot water directed into the space
heating circuit varies according to the type of the
system and of the pipe run between the plate heat
exchanger and the hydrobox.
19 The room tempera- 3-way valve failure Check the 3-way valve.
ture rises during DHW
operation.
20 Water discharges 1. If continual – pressure relief valve may be 1. Turn the handle on the pressure relief valve to check for foreign objects in it.
from pressure relief damaged. If the problem is not still solved, replace the pressure relief valve with a new
valve. one.
(Primary circuit) 2. If intermittent – expansion vessel charge may 2. Check pressure in expansion vessel.
have reduced/bladder perished. Recharge to 1 bar if necessary.
If bladder perished, replace expansion vessel with a new one.
21 Water discharges 1. If continual – field supplied pressure reducing 1. Check function of pressure reducing valve and replace if necessary.
from pressure relief valve not working.
valve (field supplied 2. If continual – pressure relief valve seat may be 2. Turn the handle on the pressure relief valve to check for foreign objects in-
item). damaged. side. If the problem is not still solved, replace the pressure relief valve.
(Sanitary circuit)
3. If intermittent – expansion vessel charge may 3. Check gas-side pressure in expansion vessel.
have reduced/bladder perished. Recharge to correct precharge pressure if necessary.
If bladder perished, replace expansion vessel with a new one with appropri-
ate pre-charge.
4. DHW tank may have subjected to backflow. 4. Check the pressure in DHW tank. If pressure in DHW tank is similar to that in
the incoming mains, cold water supply that merges with incoming mains wa-
ter supply could flow back to DHW tank. Investigate source of back-feed and
rectify error in pipework/fitting configuration. Adjust pressure in cold supply.
22 Noisy water circula- Air in water circulation pump Use manual and automatic air vents to remove air from system.
tion pump Top up water if necessary to achieve 1 bar on primary circuit.
23 Noise during hot wa- 1. Loose airing cupboard pipework 1. Install extra pipe fastening clips.
ter draw off typically 2. Heaters switching on/off 2. Normal operation, no action necessary.
worse in the morning.
24 Mechanical noise 1. Heaters switching on/off Normal operation, no action necessary.
heard coming from 2. 3-way valve changing position between DHW
the hydrobox. and heating mode
25 Water circulation Water circulation pump jam prevention mecha- Normal operation, no action necessary.
pump runs for a short nism (routine) to inhibit the build-up of scale
time unexpectedly.
26 Milky/Cloudy water Oxygenated water Water from any pressurised system will release oxygen bubbles when water is
(Sanitary circuit) running. The bubbles will settle out.
27 Heating mode has The time of “Delay” set in “Economy settings for Increase the time of “Delay” in “Economy settings for pump” .
been on standby for pump” is too short. (Go to “Service menu” → “Aux-
a long time (does iliary settings” → “Economy settings for pump”).
not start operation
smoothly.)
OCH712C 53
28 The hydrobox that The hydrobox is designed to run in an operation • Normal operation, no action necessary.
was running in the mode with a higher priority (i.e. DHW mode in this • After the DHW max. operation time has elapsed or the DHW max. temperature
heating mode before case) at power recovery. has been reached, the DHW mode switches to the other mode (ex. Heating
power failure is mode).
running in the DHW
mode after power
recovery.
29 Cooling mode is NOT DIP SW2-4 is OFF. Turn DIP SW2-4 to ON. (Refer to “6-6 DIP switch functions”.)
available.
30 The cooling system 1. When the water in the circulation circuit is 1. Normal operation, no action necessary.
does not cool down to unduly hot, Cooling mode starts with a delay
the set temperature. for the protection of the outdoor unit.
2. When the outdoor ambient temperature is 2. To run Cooling mode overriding the freeze stat. function, adjust the preset
lower than the preset temperature that acti- temperature that activates the freeze stat. function.
vates the freeze stat. function, Cooling mode (Refer to "<Freeze stat function>" on Page 30.)
does not start running.
31 The electric heaters The setting time period of Heat-pump-only opera- Adjust the setting time period of Heat-pump only operation. (Refer to “<Electric
are activated shortly tion is short. heater (DHW)> on Page 28.)
after DHW or LP
mode starts running
after Cooling mode.
32 During DHW or LP The unit runs in Cooling mode when the outdoor Do not run Cooling operation when the outdoor ambient temperature is lower
mode following the ambient temperature is lower than 10ºC (outside than 10ºC.
cooling mode, error of the guaranteed operating range). To automatically stop or recover only Cooling operation and keep other opera-
L6 (circulation water (When defrosting operation is running at such a tions running, the freeze stat. function can be used. Set the preset temperature
freeze protection low outdoor ambient temperature after Cooling that activates the freeze stat. function to adjust the outdoor ambient temperature
error ) occurs and the mode is switched to DHW or LP mode, the water as follows. (Refer to "<Freeze stat function>" on Page 30.)
system stops all the temperature in the cooling circuit drops too low, Outdoor ambient temperature Cooling operation
operations. which could result in L6 error to stop all the opera- 3ºC higher than the preset temperature Stop
tions.
5ºC higher than the preset temperature Recover
33 The energy monitor 1. Incorrect setting of the energy monitor 1. Check the setting by following the procedure below.
value seems not cor- (1) Check if the DIP switch is set as the table below.
rect. Consumed electric energy Delivered heat energy
Electric energy meter Heat meter
SW3-4 SW3-8
Note: (Local supply) (Local supply)
There could be some OFF Without OFF Without
discrepancies between ON With ON With
the actual and the
calculated values. (2) In the case external electric energy meter and/or heat meter is not used,
If you seek for accuracy, check if the setting for electric heater and water pump(s) input is correct
please make sure to by referring to <Energy monitor setting> in "9-4 Service menu".
connect power meter(s)
(3) In the case external electric energy meter and/or heat meter is used,
and heat meter to FTC
check if the unit of output pulse on external meter matches with the one
board. Both should be
locally supplied. set at the main remote controller by referring to <Energy monitor setting>
in "9-4. Service menu".
2. Non-connectable type of external meter (local 2. heck if the external meter (local supply) is connectable type by referring to
C
supply) is connected. <Energy monitor setting>" in "9-4 Service menu".
3. External meter (local supply) failure 3. heck if signal is sent to IN8 to IN10 properly. (Refer to "6. WIRING
C
DIAGRAM".)
Replace the external heat meter if defective.
4. FTC board failure 4. Check the FTC control board.
Replace the board.
34 Heat pump is forced Smart grid ready input (IN11 and IN12) is used, Normal operation, no action necessary.
to turn ON and OFF. and switch-on and off commands are input.
Annual Maintenance
It is essential that the hydrobox is serviced at least once a year by a qualified individual any spare parts required MUST be purchased from Mitsubishi Electric (safety
matter).
NEVER bypass safety devices or operate the unit without them being fully operational.
<Annual maintenance points>

Use the Annual Maintenance Log Book ("13-1. Annual Maintenance") as a guide to carrying out the necessary checks on the hydrobox and outdoor unit.
OCH712C 54
10-6. Checking Component Parts' Function
Part Name Checkpoints
<Water Circulation Pump Characteristics>

ERSC series
External static pressure [kPa]

80.0
Speed 5 (Default setting)
BROWN
PWM input signal 70.0 Speed 4
Signal cable BLUE
Signal ref. 60.0 Speed 3
3 BLACK 50.0 Speed 2
Feedback signal Speed 1
M 40.0
1~ BROWN
L 30.0
3 BLUE N
20.0
Power cable 10.0
GREEN/
YELLOW 0.0
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0
Flow rate [L/min]
<Figure 10.6.1>
ERSD series
80.0

70.0 Speed 4
60.0 Speed 3
Speed 2
<Recommended water flow rate range> 50.0 Speed 1
40.0
Outdoor heat pump unit Water flow rate range [L/min] 30.0
Packaged model PUZ-WM50 6.5 – 14.3 20.0
PUZ-WM60 8.6 – 17.2 10.0
PUZ-WM85 10.8 – 24.4 0.0
PUZ-WM112 14.4 – 32.1 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0
PUZ-HWM140 17.9 – 40.1 Flow rate [L/min]
Split model SUZ-SWM40 6.5 – 11.4 <Figure 10.6.2>
SUZ-SWM60 7.2 – 17.2
EHSC series
SUZ-SWM80 7.8 – 21.5 80.0

PUD-S(H)WM60 9.0 – 22.9 70.0 Speed 4
PUD-S(H)WM80 9.0 – 22.9 60.0 Speed 3
Speed 2
PUD-S(H)WM100 14.3 – 34.4 50.0 Speed 1
PUD-S(H)WM120 14.3 – 34.4 40.0
PUD-SHWM140 14.3 – 34.4 30.0
PUHZ-FRP71 11.5 – 22.9 20.0
PUHZ-SW75 10.2 – 22.9 10.0
PUHZ-SW100 14.4 – 32.1 0.0
PUHZ-SW120 20.1 – 36.9 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0
PUHZ-SHW80 10.2 – 22.9 Flow rate [L/min]
PUHZ-SHW112 14.4 – 32.1 <Figure 10.6.3>
PUHZ-SHW140 17.9 – 36.9
PUMY-P112 17.9 – 35.8 E*SE series
140.0
PUMY-P125 17.9 – 35.8 Speed 5 (Default setting)
PUMY-P140 17.9 – 35.8 120.0 Speed 4

Speed 3
<Table 10.6.1> 100.0 Speed 2
80.0 Speed 1
* If the water flow rate is less than the minimum flow rate setting of
60.0
the flow sensor(default 5.0 L/min), the flow rate error will be acti-
vated. 40.0
If the water flow rate exceeds 36.9 L/min, the flow speed will be 20.0
greater than 2.0 m/s, which could erode the pipes. 0.0
0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0
Flow rate [L/min]
<Figure 10.6.4>
E*PX series EHSD series
80.0
80.0

70.0 Speed 5
(Default setting) 70.0 Speed 4
60.0 Speed 4
60.0 Speed 3
Speed 3 Speed 2
50.0 Speed 2
50.0 Speed 1
40.0 Speed 1 40.0
30.0 30.0
20.0 20.0
10.0 10.0
0.0 0.0
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0
Flow rate [L/min] Flow rate [L/min]
<Figure 10.6.6> <Figure 10.6.5>
Note: F
or installation of E*PX series, set its pump speed with a pressure drop between
the hydrobox and the outdoor unit factored into the external static pressure.
OCH712C 55
Earth leakage circuit breaker for heater If a short circuit occurs on the booster heater, immersion heater, or each power line, a
short-circuit breaker will trip and power source will be blocked.
Eliminate the causes of short circuit and then turn on the breaker again.
Relay for heater When the applied voltage is not 230 VAC across the terminals A1-A2, check the terminals
R S T A1 A2 R-U, S-V, and T-W are open.
When the applied voltage is 230 VAC across the terminals A1-A2, check the terminals
R-U, S-V, and T-W are short.
U V W
Booster heater Measure the resistance between the terminals with a multimeter.
Thermostat (90°C) and thermal cut out (121°C)

Terminal Normal Abnormal
121 °C 90 °C
Thermal Manual reset
9–10 80(±20) mΩ Open or Short
cut-out water
thermostat
AWG18
AWG18
9 10
2 kW heater (230 V, 1 phase)

2 kW Terminal Normal Abnormal
1–2 26.5(+3/−1.3) Ω Open or Short
AWG15 FEP
AWG15 FEP
WHITE
WHITE
1 2
2 + 4 kW heater (230 V, 1 phase)

2 kW Terminal Normal Abnormal
1–2 26.5(+3/−1.3) Ω Open or Short
2 kW 2 kW 3–4 13.3(+1.5/−0.6) Ω Open or Short
AWG15 FEP
AWG15 FEP
AWG13 FEP
AWG13 FEP
WHITE
WHITE
BLUE
BLUE
1 2 3 4

1 kW 2 kW 1–2=2–3=1–3 105.8(+11.8/−5) Ω Open or Short
1 kW 1 kW
4–5=5–6=4–6 52.9(+5.8/−2.5) Ω Open or Short
2 kW 2 kW
AWG15 FEP
AWG15 FEP
AWG15 FEP
AWG13 FEP
AWG13 FEP
AWG13 FEP
WHITE
WHITE
WHITE
BLUE
BLUE
BLUE
1 2 3 4 5 6

1–2=2–3=3–1 35.3(+3.9/−1.8) Ω Open or Short
1 kW 1 kW 2 kW 2 kW 4–5=5–6=6–4 17.6(+1.9/−0.9) Ω Open or Short
1 kW 2 kW
AWG15 FEP
AWG15 FEP
AWG15 FEP
AWG13 FEP
AWG13 FEP
AWG13 FEP
WHITE
WHITE
WHITE
BLUE
BLUE
BLUE
1 2 3 4 5 6
OCH712C 56
Thermistors Disconnect the connector then measure the resistance with a multimeter.
(At ambient temperatures of 10 to 30°C.)
Thermistor Normal Abnormal

TH1
TH2
THW1
THW2
THW5A
4.3 to 9.5 kΩ Open or short
THW5B
THW6
THW7
THW8
THW9
THW10
40 to 100 kΩ Open or short
THWB1
Flow sensor
FTC CONTROLLER BOARD Flow signal
4.0
CN1A WH 3.5
Flow output signal[V]
BK 1 3.0
WITHOUT SIGNAL
2 2.5
Vout WH MICRO
SENSOR
PROCESSOR 2.0
BU 3
5 VDC 1.5
BN 4
1.0
0.5
0.35 V
0.0
4-3 : 5 V (DC) 0 20 40 60 80 100
2-3 : Output Vout (DC) Flow [L/min]
Pressure sensor FTC CONTROLLER

FTC CONTROLLER BOARD
Vout (V)
CN401 WH 5 VDC
CN401 WH 5 VDC
4.5 RD 1
RD 1
SENSOR
SENSOR
BK 3 2.5 BK 3
Vout WH 4 MICRO Vout WH 4 M

PROCESSOR PROC
0.5
5 PRESSURE
(MPa) 2.5 5 PRESSURE
(MPa)
1-3 : 5 V (DC)
3-4 : Output Vout (DC) 1-3 : 5 V (DC)
3-4 : Output Vout (DC)
OCH712C 57
<Thermistors Characteristics Charts>
50
• Room temperature thermistor (TH1)
• Refrigerant liquid temperature thermistor (TH2)
• Flow water temperature thermistor (THW1)
• Return water temperature thermistor (THW2)
• DHW tank water temperature thermistor (THW5A/5B) 40
• Zone1 flow temperature thermistor (THW6)
• Zone1 return temperature thermistor (THW7)
Resistance (k")
• Zone2 flow temperature thermistor (THW8)
• Zone2 return temperature thermistor (THW9) 30
Thermistor R0 = 15 kΩ ± 3%
B constant = 3480 ± 2% 20
1 1
Rt = 15exp {3480 ( 273+t – 273 )}
0°C 15 kΩ
10
10°C 9.6 kΩ
20°C 6.3 kΩ
25°C 5.2 kΩ
30°C 4.3 kΩ 0
40°C 3.0 kΩ
-20 -10 0 10 20 30 40 50
Temperature (°C)
• Boiler flow temperature thermistor (THWB1)

1000
• Mixing tank temperature thermistor (THW10)
900
Thermistor R100 = 3.3 kΩ ± 2%
B constant = 3970 ± 1%
800
1 1
Rt = 3.3 exp {3970 ( 273+t – 273 )} 700
Resistance (k")
600
0°C 162.8 kΩ
10°C 97.4 kΩ 500
20°C 60.3 kΩ
25°C 48.1 kΩ 400
30°C 38.6 kΩ
40°C 25.4 kΩ
300
50°C 17.1 kΩ
60°C 11.9 kΩ
70°C 8.4 kΩ
200
80°C 6.0 kΩ
100
0
-30 -20 -10 0 10 20 30 40 50 60 70 80
Temperature (°C)
OCH712C 58
10-7. Test point diagram
FTC (Controller board)

CNP1/OUT1 (TBO.1 1-2)
Water circulation pump1
(230 VAC)
OUT2 (TBO.1 3-4)

(Local supply) (230 VAC)
CN01
OUT3 (TBO.1 5-6)
Power supply
(3-5: 230 VAC)
(Local supply) (230 VAC)
CNP4/OUT14
F1
(230 VAC)
10 A/250 V
OUT5 (TBO.2 1-3)
Mixing valve (Local supply) F2
(1-2[Close]: 230 VAC) 6.3 A/250 V
(2-3[Open]: 230 VAC)
CN3C
OUT4 (TBO.2 4-6) Transmission
3-way valve/2-way valve (Indoor/Outdoor)
(Local supply) (0–24 VDC)
(4-5: 230 VAC) LED1
OUT10 (TBO.3 1-2) Power supply (FTC)
Signal output (Boiler) CNPWM
(non-voltage contact) Water circulation
pump 1
(2-3: 5 VDC)
LED2
OUT11 (TBO.3 5-6) Power supply (Main
Signal output (Error) (230 VAC) remote controller)
LED3
OUT12 (TBO.3 7-8) Transmission
Signal output (Defrost) (230 VAC) (Indoor/Outdoor)
OUT15 (TBO.4 1-2) CNRF
Signal output (Comp on) Transmission (Indoor/
(230 VAC) Wireless receiver)
OUT13 (TBO.4 3-4) (1-2: 11.5–13.2 VDC)
2-way valve2 (230 VAC) CN105
Transmission (Indoor/
CNIH/OUT9 (TBO.4 5-6) WiFi adaptor)
Signal output for immersion (1-2: 11.5–13.2 VDC)
heater (230 VAC)
LED4
OUT8 (TBO.4 7-8) Reading or writing
Signal output (Cooling) data to SD card
(230 VAC) CN22
Main remote controller
CNBHT (10.4–13.7 VDC)
Thermostat input for CN108
booster heater SD card
CNBC
CN21
Signal output for booster heater
Thermistor
(230 VAC)
(Ref. liquid temp.)
CNBH CN20
Signal output for booster heater Thermistor
(1-3: heater1 230 VAC) (Room temp.)
(5-7: heater2 230 VAC) CNW12
Thermistor
(1-2: Flow water temp.)
(3-4: Return water temp.)
THW10
IN1 (TBI.6 5-6)
CN1A Thermistor
(TBI.1 7-8)
Flow sensor (Mixing tank temp.)
Room thermostat IN7
input THWB1
input (TBI.2 3-4)
THW7 (TBI.6 7-8)
Flow switch
IN2 IN4 IN8 (TBI.5 5-6) Thermistor
IN6 3 input
(TBI.1 5-6) (TBI.1 1-2) (TBI.3 7-8) Thermistor (Boiler flow
Flow switch 1 (TBI.2 5-6) (Zone1 return
Demand Power meter IN12 water temp.)
input Room thermostat water temp. )
control input 1 input (TBI.3 1-2)
2 input
IN3 Smart grid
IN5 IN10 IN9 THW6 (TBI.5 7-8) THW9 (TBI.5 1-2)
(TBI.1 3-4) ready 2 input
(TBI.2 7-8) (TBI.2 1-2) (TBI.3 5-6) Thermistor Thermistor
Flow switch Outdoor ther- (Zone2 return water temp.)
Heat meter Power meter IN11 (TBI.3 3-4) (Zone1 flow water temp.)
2 input mostat input input 2 input Smart grid THW8 (TBI.5 3-4)
CNW5 Thermistor
ready 1 input (DHW tank water temp.) Thermistor
(Zone2 flow water temp. )
OCH712C 59
11 DISASSEMBLY PROCEDURE
<Preparation for the repair service>
● Prepare the proper tools.
● Prepare the proper protectors.
● Provide adequate ventilation.
● After stopping the operation of the hydrobox and outdoor unit, turn off all the power-supply breaker.
● Discharge the condenser before the work involving the electric parts.
● Allow parts to cool.
● Do not expose the electric parts to water.
● When replacing or servicing water circuit parts, drain system first.
Check individual illustrations and positions of the parts by referring to the parts catalogue.
Some lead wires and pipes are bundled with Bands. Cut the bands to undo the fastened pipes and lead wires if necessary.
When bundling the lead wires and pipes again, use new commercially available bands.
When removing the parts associated with water pipe work, drain the hydrobox as necessary. (Refer to "Draining the Hydrobox"
on page 21.)
When draining the hydrobox, keep water from splashing on the internal parts (mainly electric parts and insulations).
: Indicates the visible parts in the photos/figures.

: Indicates the invisible parts in the photos/figures.
DISASSEMBLY PROCEDURE PHOTOS/ FIGURES

1. How to remove the front panel Photo 1-1
(1) Remove the 2 screws at the bottom of the hydrobox.
(Photo 1-1)
(2) Slightly lift and pull out the front panel from the hydrobox.
(Photo 1-1)
(3) Disconnect the relay connector connecting from the
remocon assy. (Photo 1-2)
Front panel
Photo 1-2
Connector Remocon assy
Screws
Remocon
assy
2. How to remove the remocon assy

(1) Remove the front panel. (Refer to Procedure 1.) Photo 2-1
(2) Turn the front panel over and remove the 5 claws at the Remocon support Front panel
remocon holder. (Photo 2-1)
(3) Slide the remocon support upward, then remove it
together with the main remote controller. (Photo 2-2)
(4) Separate the remocon assy from the remocon support.
(Photo 2-3)
Claws
Photo 2-2 Remocon support Photo 2-3 Remocon assy

Remocon
holder
Claw
OCH712C 60
3. How to remove the electrical parts Photo 3-1 Control box fixing screws
(Steps (1) through (3) are applied to all the following parts.)
(1) R emove the front panel. (Refer to Procedure 1.)
(2) Remove the 4 screws holding the control box. (Photo
3-1)
(3) S lightly lift and pull out the control box. (Photo 3-1)
<Earth leakage circuit breaker> (Photo 3-2)
(4) Disconnect all the lead wires from the earth leakage cir-
cuit breaker.
(5) Remove the 2 screws on the earth leakage circuit breaker.
Note: To avoid dropping of the breaker, hold the breaker by
hand when removing the last screws.
<Contactor> (Photo 3-2)

(4) Disconnect all the lead wires from the contactors.
(5) Remove the 2 screws on each contactor.
Note: To avoid dropping of the contactors, hold the contac-
tors by hand when removing the last screws.
Note: T
he photo shown is of the EHSD-MED.UK model.
To prevent an electrical shock, wait until all the LED
lamps on the FTC control board are turned off.
Photo 3-2
Earth leakage circuit Control box
<Terminal block> (Photo 3-2) Controller board breaker (ECB1)
(4) Disconnect all the lead wires from the terminal block. (To
disconnect the S1, S2 and S3 lead wires, disengage the
locks by pressing on the claws.)
(5) Remove the screw on the terminal block.
Note: To avoid dropping of the terminal block, hold the termi- Screws
nal block by hand when removing the screw.
<Controller board> (Photo 3-3)

(4) Disconnect all the lead wires from the controller board.
(5) Remove the controller board from the 4 board supports.
Screw
Terminal block (TB1) Contactors
Note: T
he photo shown is of the ERSE-YM9ED.UK model.
Photo 3-3 Board supports
Controller
board
Board supports
OCH712C 61
4. How to swing the control box to the front Photo 4-1
(1) Remove the front panel. (Refer to Procedure 1.) Earth cable Side panel
(2) R emove the 2 screws from the control box bracket (R) and
the 2 screws from the control box bracket (L). (Photo 4-1
and 4-2)
(3) Disengage the control box bracket (R) from the right-hand
side panel and pull the control box. At this point, lifting
slightly and pulling the control box will swing the control
box to the front. (Photo 4-3)
Screws
Screws
Note: Disconnect the field wiring as necessary.
Cable strap Bracket

(R)
Note: The photo shown is of the EHSD-MED.UK model.
Photo 4-2
Earth cable Side panel Photo 4-3
Control box
Screws
Screws
Swing
Bracket
Cable strap (R)
Note: The photo shown is of the ERSE-YM9ED.UK model.
OCH712C 62
5. How to remove water pump/ pump valve Photo 5-1
<Water pump> Water pump
Close the pump valve (OFF) before removing the water pump, connector (CNP1) CNPWM
Earth cable connector
and open the valves (ON) after reinstalling the water pump.
(1) Remove the front panel. (Refer to Procedure 1.)
(2) D
isconnect the CNP1 connector, the earth cable, and the
CNPWM connector on the controller board. (Photo 5-1)
(3) <E*SC/D series>
Release the water pump lead wire from the fastener, the
2 cable clamps and the 2 cable straps. Feed the lead Lead
wire out the control box without putting strain on the wire
CNP1 and the CNPWM connectors. (Photo 5-1)
Cable
<E*SE series and E*PX series> clamps
Release the water pump lead wire from the fastener, the Lead
2 cable clamps and the cable strap. Feed the lead wire wire
out the control box without putting strain on the CNP1
and the CNPWM connectors. (Photo 5-1)
(4) Swing the control box to the front. (Refer to Procedure 4.)
(5) <E*SC/D series>
Close (OFF) the pump valve and remove the G1" nuts using
2 spanners: one to hold the G1" nut and the other to turn the
other side of G1" nut.
Remove the water pump by sliding it horizontally. (Photo 5-2) Fastener
• When the pump valve handle is stiff, turn the handle 90 Cable straps
degrees clockwise mainly by using a spanner.
• When reinstalling the G1" nuts, use new G1" gaskets.
(Photo 5-3) Photo 5-2 (E*SC/D series)
• Set the water pump in the way that the die stamped
arrow facing down, and the lead wire connectors facing
to the left. (Photo 5-2) Gasket (G1")
• Be sure to change the pump and the water pump lead Nut (G1")
wire together.
Lead wire Flow direction
• Be sure to wipe water around the surface of the pump connectors
and the water pump lead wire thoroughly.
Water pump
Nut (G1")
Gasket (G1")
Pump valve Pump valve Quick

Screws O-ring connection
stay
Photo 5-3 (E*SC/D and E*PX series)
Photo 5-4 (E*SC/D and E*PX series)
Pump valve
Screws stay
Gasket G1"
OCH712C 63
5. How to remove water pump/ pump valve Photo 5-5 (E*SE series)
(5) <E*SE series>
Close (OFF) the pump valve and remove the G1-1/2" Gasket (G1-1/2")
nuts using 2 spanners: one to hold the G1-1/2" nut and Nut (G1-1/2")
the other to turn the other side of G1-1/2" nut.
Remove the water pump by sliding it horizontally. Terminal box
(Photo 5-5) Flow direction
• When the pump valve handle is stiff, turn the handle Water pump
90 degrees clockwise mainly by using a spanner. Gasket (G1-1/2")
• When opening or closing the pump valve, ensure to do
Nut (G1-1/2")
so fully, not halfway.
• When reinstalling the G1-1/2" nuts, use new G1-1/2"
gaskets. (Photo 5-6)
arrow facing down, and the terminal box facing to the
left. (Photo 5-5) Pump valve
• Be sure to change the pump and the water pump lead
wire together. Pump valve
stay
Screws O-ring Different
• Be sure to wipe water around the surface of the pump diameter
quick connection
and the water pump lead wire thoroughly.
<E*PX series>
Close (OFF) the pump valve and remove the G1" nuts
using 2 spanners: one to hold the G1" nut and the other Strainer valve
to turn the other side of G1" nut.
Remove the water pump by sliding it vertically. (Photo Photo 5-6 (E*SE series) Photo 5-7 (E*SE series)
5-8) Gasket (G1-1/2")
Screws Pump valve
• When the pump valve handle and the strainer valve stay
handle are stiff, turn the handle 90 degrees clockwise
mainly by using a spanner.
• When opening or closing the pump valve and the
strainer valve, ensure to do so fully, not halfway.
• When reinstalling the G1" nuts, use new G1" gaskets.
(Photo 5-3)
arrow facing left, and the lead wire connectors facing
to the up. (Photo 5-8)
• Be sure to change the pump and the water pump lead
wire together.
• Be sure to wipe water around the surface of the pump
and the water pump lead wire thoroughly. Photo 5-8 (E*PX series)
Gasket (G1") Nut (G1") Lead wire connectors
<Pump valve>
(6) Remove the 2 screws fixing the pump valve stay.
(Photos 5-2, 5-5 and 5-8)
(7) Remove the pump valve by detaching the quick con-
nection. (Photos 5-2, 5-5 and 5-8) Flow direction
• When reinstalling the quick connection, use new
O-ring.
• When the pump valve handle is stiff, turn the handle
90 degrees clockwise mainly by using a spanner.
• When reinstalling the pump valve, place the handle to
the left hand side of the pump valve.
• When opening or closing the pump valve, ensure to do
Screws Water pump
so fully, not halfway. Nut (G1")
Pump valve Pump valve
• Reuse the removed pump valve stay and the pump Gasket (G1")
stay
valve stay fixing screws. (Photos 5-4 and 5-7) O-ring
• Refer to Procedure 16 for how to attach and detach
Quick connection
the quick connection.
Note: Skip Steps (2) and (3) above when replacing the
pump valves only.
OCH712C 64
6. How to remove the flow sensor Photo 6-1 CN1A
(1) Remove the front panel. (Refer to Procedure 1.) connector
(2) D
isconnect the CN1A connector on the controller board.
(Photo 6-1)
(3) Release the flow sensor lead wire from the fastener and
the 2 cable straps. Feed the lead wire out the control box
without putting strain on the CN1A connector. (Photo 6-1)
(4) S
wing the control box to the front. (Refer to Procedure 4.)
(5) Remove the flow sensor by detaching the same diameter
quick connection. (Photo 6-2) Lead wire
•W hen reinstalling the flow sensor, use new O-rings.
(Photo 6-3)
• <E*SC/D series and E*PX series>
Set the flow sensor in the orientation of the arrow
printed on the flow sensor and in the way that the
sensor part faces to the left. (Photo 6-2)
<E*SE series>
Set the flow sensor in the orientation of the arrow
printed on the flow sensor and in the way that the
sensor part faces to the front.
• Refer to Procedure 16 for how to attach and detach the Cable straps Fastener
quick connection.
Photo 6-3 Photo 6-2

Sensor part
Same diameter
quick connection
O-ring
Flow sensor
Flow direction
O-rings
O-ring
Same diameter
quick connection
Note: The photo shown is of the EHSD-MED.UK model.
7. How to remove the booster heater Photo 7-1

(Steps (1) through (4) are applied to all the following units.) Booster heater Control box
(1) Remove the front panel. (Refer to Procedure 1.) connector (CNBHT)
(2) D isconnect the booster heater lead wires from the CNBHT
connector on the controller board and from the BHC1
(Lead wire No.1, No.2 and No.3) and BHC2 (Lead wire
No.4, No. 5 and No.6) contactors respectively. (Photo 7-1)
(3) Release the booster heater lead wire from the 2 cable
straps. Feed the lead wires put the control box without
putting strain on the CNBHT connector, the BHC1 and
BHC2 contactors. (Photo 7-1)
BHC1
(4) S wing the control box to the front. (Refer to Procedure 4.)
Note: Do not mix up the lead wire numbers when BHC2
re-connecting the lead wires to the contactors as
the lead wire numbers are different depending on Lead
No.1
No.2
No.3
No.4
No.5
No.6
the models. wire
Cable straps
Note: The photo shown is of the ERSE-YM9ED.UK model.
OCH712C 65
7. How to remove the booster heater Photo 7-2 (E*S* series)
Quick connection Back panel Flare nut
Model Lead wire No. Contactor
EHSC-VM2D ERSC-VM2D No.1 BHC1-U
EHSD-VM2D ERSD-VM2D No.2 BHC1-V
EHPX-VM2D ERPX-VM2D O-ring Booster
EHSC-VM6D EHSD-VM6D No.1 BHC1-U heater
EHPX-VM6D ERSD-VM6D No.2 BHC1-V
ERSC-VM6D ERPX-VM6D No.4 BHC2-U
No.5 BHC2-V
EHSC-YM9D EHSC-YM9ED No.1 BHC1-U
EHSC-TM9D EHSD-YM9C No.2 BHC1-V
EHSD-YM9ED EHSD-TM9D No.3 BHC1-W
EHSE-YM9ED ERSE-YM9ED L joint
No.4 BHC2-U
EHPX-YM9D EHPX-YM9ED No.5 BHC2-V Heater stay
ERSD-YM9D ERSC-YM9D No.6 BHC2-W
ERPX-YM9D Screws
Refer to 6. WIRING DIAGRAM
Pipe (B.H.-F.S.)
<E*S* series and E*PX series>

(5) <Only E*SC/D series> Flow sensor
Remove the pump valve. (Refer to Procedure 5.)
(6) Remove the flow sensor. (Refer to Procedure 6.)
(7) Remove the L joint and the pipe (B.H.-F.S.) by detaching
the quick connection. (Photos 7-2 and 7-3)
• When reinstalling the quick connection, use new O-ring.
Pump valve O-ring
• Refer to Procedure 16 for how to attach and detach the
Pipe Quick
quick connection. (PUMP-B.H.) connection
(8) Remove the flare nut. (Photos 7-2 and 7-3)
(9) <Only E*SC/D series> Note: The photo shown is of the EHSC-VM2ED.UK model.
Remove the pipe (PUMP-B.H.) by detaching the quick
connection. (Photo 7-2)
<Only E*PX series>
Remove the pipe (OUT-B.H.) by detaching the quick Photo 7-3 (E*PX series)
connection. (Photo 7-3) Flare nut
• When reinstalling the quick connection, use new O-ring. Quick connection
quick connection.
O-ring
(10) <Only E*PX series> Back Screw
Remove the saddle band and the rubber tube by panel Booster
removing the 2 screws on the saddle band. (Photo 7-3) heater
(11) Remove the 2 screws that hold the heater stay onto the Heater stay
Quick
back panel. Lift the booster heater slightly and remove connection Flow
the booster heater with the heater stay from the back Screw sensor
panel. (Photos 7-2, 7-3 and 7-4) O-ring
(12) Remove the 2 screws on the back of the heater stay Pipe
and remove the heater stay from the booster heater. (OUT-BH)
(Photo 7-4)
• Reuse the removed heater stay and the screws.
Photo 7-4
Screws
Screws Saddle band

Rubber tube
Heater stay
OCH712C 66
8. How to remove the plate heat exchanger
(Steps (1) through (9) are applied to the following E*SC/D series.)
(1) Pump down the refrigerant circuit and close the stop valve on the
outdoor unit. (Refer to "12. Supplementary information".)
(4) Release the lead wires from the coated clamp. (Photo 8-1)
(5) C lose the strainer valve (OFF). (Photos 8-1, 8-5 and 8-7)
•W hen the strainer valve handle is stiff, turn the handle 90 degrees
clockwise mainly by using a spanner.
•W hen opening or closing the strainer valve, ensure to do so fully, not
halfway.
(6) Remove the water pump and the pump valve. (Refer to Procedure 5.)
(7) R emove the expansion vessel. (Refer to Procedure 12.)
(8) R emove the saddle band (upper the pump) and the rubber tube by
removing the 2 screws on the saddle band. (Photo 8-1)
(9) R emove the pipe (W.C.-PUMP) by detaching the quick connection.
(Photos 8-1 and 8-5)
• When reinstalling the quick connection, use a new O-ring.
• Refer to Procedure 16 for how to attach and detach the quick
connection.
(10) R emove the flare nuts on the gas and liquid pipes under the
hydrobox using 2 spanners: one to hold each flare joint and the
other to turn each flare nut.
Photo 8-1 (E*SC series)

Pipe (W.C.-PUMP) Saddle band
Quick connection O-ring (upper the pump) Rubber tube
Screw
Expansion vessel
Screw
Water pump
Screws
Water coil cover Pipe (PUMP-B.H.)
Plate heat exchanger

(inside)
Pump valve
Quick connection
O-ring
Coated clamp
Quick connection
O-ring
Strainer valve Gasket (G1") Nut (G1")
OCH712C 67
8. How to remove the plate heat exchanger (continued) Photo 8-2 (EHSC series)
<E*SC series>
(11) Remove the G1" nut on the water outlet side of the
strainer valve using 2 spanners: one to hold the strainer
valve and the other to turn the G1" nut. (Photos 8-1 and
8-4)
• When reinstalling the G1" nut, use a new G1" gasket.
(12) <Only EHSC series>
Remove the 2 screws on the strainer valve stay. (Photo
8-4)
(13) <ERSC series>
Remove the pipe (STR-W.C.) by detaching the quick
connection from the plate heat exchanger. (Photo 8-4)
<EHSC series>
Remove the strainer valve by detaching the quick
Plate heat
connection from the plate heat exchanger. (Photo 8-1) exchanger
•W hen reinstalling the quick connections, use a new O-ring.
quick connection.
(14) Remove the TH2 thermistor from the thermistor holder.
(Refer to Procedure 14. Photos 14-2 and 14-3) O-ring
(15) Remove the water coil cover by removing the 2 screws.
(Photo 8-1)
(16) Pull out the plate heat exchanger from the hydrobox by
lifting it upward. (Photos 8-2 and 8-3) Quick con- Strainer Screws Strainer valve
nection valve stay
Photo 8-3
Photo 8-4 (ERSC series)
Plate heat
exchanger
(inside)
O-ring
Quick
connection
TH2 thermistor
Strainer valve Pipe
(STR-W.C.)
Gasket (G1") Nut (G1")
OCH712C 68
8. How to remove the plate heat exchanger (continued)
<E*SD series> Photo 8-6 (E*SD series)
(11) <Only ERSD series>
emove the saddle band (upper the strainer) and the
R
rubber tube by removing the 2 screws on the saddle band.
(12) Detach the quick connection for the L joint (Lower), the
plate heat exchanger, and rotate forward the pipe (STR- Plate heat
exchanger
W.C.) with the L joint (lower) by using the quick (inside)
connection (upper the strainer) as a fulcrum. Screws
• When reinstalling the quick connection, use a new O-ring.
quick connection.
(13) R emove the TH2 thermistor from the thermistor holder.
(Refer to Procedure 14. Photos 14-2 and 14-3) Water coil
cover
(14) Remove the plate heat exchanger with water coil cover
by lifting it upward after removing the 2 screws on the Water coil
base
water coil cover. (Photo 8-5)
(15) Remove the water coil cover and the water coil base by
removing the 4 screws. (Photo 8-6)
Photo 8-5 (E*SD series)

Rubber tube
O-ring Pipe (W.C.-PUMP)
Screw Screw
Quick connection
L joint (upper)
Saddle band
Screw (upper the pump)
(inside)
Water coil cover Nut (G1")
Pump valve Water pump
Quick connection Pipe (PUMP-B.H.)
L joint (lower)
O-ring
Coated clamp
Pipe (STR-W.C.)
Screws
O-ring
Quick connection
(upper strainer)
TH2 thermistor
Strainer valve
OCH712C 69
8. How to remove the plate heat exchanger (continued)
<E*SE series>
(1) Pump down the refrigerant circuit and close the stop valve on
the outdoor unit. (Refer to "12. Supplementary information".)
(4) Release the lead wires from the coated clamp. (Photo 8-7)
(5) Close the strainer valve (OFF). (Photo 8-7)
• When the strainer valve handle is stiff, turn the handle 90
degrees clockwise mainly by using a spanner. (Photo 8-7)
• When opening or closing the strainer valve, ensure to do so
fully, not halfway.
(6) Remove the water pump and the pump valve. (Refer to
Procedure 5.)
(7) Remove the joint (WC-PUMP) by removing the 2 screws, and
detaching the different diameter quick connection. (Photo 8-7)
•W hen reinstalling the different diameter quick connection,
use a new O-ring.
• Refer to Procedure 16 for how to attach and detach the quick
connection.
Photo 8-7
Different diameter Joint
quick connection O-ring (W.C.-PUMP) Screws
Screws
Booster heater
Water coil cover
Nut (G1-1/2")
Pipe
(P.V.-B.H.)
Screw
Water pump
Nut (G1-1/2")
Pump valve Different diameter
quick connection
Screw O-ring

(inside) Strainer valve
Coated clamp
O-ring Same diameter

quick connection
Screws Different diameter

quick connection O-ring
TH2 thermistor
OCH712C 70
8. How to remove the plate heat exchanger (continued) Photo 8-8 Different diameter
(8) Remove the strainer valve by removing the 2 screws, and quick connection
detaching the same diameter quick connection. (Photo 8-8)
•W hen reinstalling the same diameter quick connection,
use a new O-ring.
• Refer to procedure 16 for how to attach and detach the
quick connection.
(9) R
emove the flare nuts on the gas and liquid pipes under
the hydrobox using 2 spanners: one to hold each flare joint
Strainer valve
and the other to turn each flare nut.
(10) R emove the TH2 thermistor from the thermistor holder.
(Photo 8-7 and refer to Procedure 14. Photo 14-2) Screws
(11) Remove the water coil cover by removing the 6 screws.
(Photo 8-7)
(12) P ull out the plate heat exchanger from the hydrobox by
lifting it upward. (Photos 8-9 and 8-10)
(13) R emove the strainer valve by detaching the different
diameter quick connection from the plate heat exchanger.
(Photos 8-8 and 8-9)
•W hen reinstalling the different diameter quick connection, Same
diameter
use a new O-ring. quick
• Refer to Procedure 16 for how to attach and detach the connection
quick connection.
Photo 8-10 Plate heat exchanger (inside) TH2 thermistor
Photo 8-9
Strainer valve
9. How to remove the pressure sensor Photo 9

<Only E*SD series>
(1) Remove the plate heat exchanger. (Refer to Procedure 8.)
(2) R
emove the band. (Photo 9.)
(3) Remove the welded part of the pressure sensor. Be sure
not to burn the pipe cover. (Photo 9.)
Note: The temperature of the pressure sensor must be Pressure
100 °C or below when welding. Plate heat sensor
exchanger
(inside)
Welding
part
Band
OCH712C 71
10. How to remove the strainer Photo 10-1 (ERS* series)
Quick Strainer Strainer
(2) Swing the control box to the front. (Refer to Procedure 4.) O-ring connection valve valve stay
Screws
(3) Close the strainer valve (OFF). (Photos 10-1, 10-4 and
10-6)
• When the strainer valve handle is stiff, turn the handle
90 degrees clockwise mainly by using a spanner.
• When opening or closing the strainer valve, ensure to
do so fully, not halfway.
(4) Remove the 2 screws on the strainer valve stay. (Photos
10-1, 10-4 and 10-6)
(5) Remove the G1" nut using 2 spanners: one to hold the
strainer and the other to turn the G1" nut. (Photos 10-1,
10-4 and 10-6)
• When reinstalling the G1" nut, use new G1" gasket.
Strainer mesh Cover Gasket Nut
(6) Detach the quick connection. (Photos 10-1, 10-4 and (inside) (G1") (G1")
10-6)
• When reinstalling the quick connection, use new O-ring. Photo 10-2 (ERS* series)
quick connection.
(7) Remove the strainer valve stay by removing the 2
screws. (Photos 10-2 and 10-5)
• Reuse the removed L joint, the strainer valve stay and
the strainer valve stay fixing screws.
<Removal of the strainer cover (debris recovery)>
(4) Remove the cover with 2 spanners: one to hold the
strainer valve and the other to turn the cover. (Photos
10-1, 10-4 and 10-6)
• Be sure to reattach the mesh after washing. (Photo 10-3)
• When reinstalling the cover, use a new packing.
Strainer valve stay Strainer valve stay
fixing screws
Photo 10-3 Photo 10-4 (EHS* series)
Quick Strainer Gasket
Strainer mesh O-ring connection valve (G1") Nut (G1")
Cover Packing
Cover Strainer Screws Strainer mesh
valve stay (inside)
Photo 10-5 (EHS* series) Photo 10-6 (E*PX series)

Strainer valve stay O-ring Quick connection
Strainer valve stay Strainer mesh Strainer valve

Strainer valve stay Nut (G1") Gasket
fixing screws (G1") Screws (inside)
OCH712C 72
11. How to remove the manometer/ pressure relief valve/ air
Photo 11-1
vent (automatic)
Claw Screw
(2) S
<Manometer>
(3) Remove the screw on the manometer cover. (Photo Manometer
11-1)
(4) H old the sides of the manometer cover, disengage the 2
claws, and remove the manometer with cover. (Photo
11-1)
(5) Remove the G1/4" nut and feed the capillary tube Manometer
cover
throughout the hydrobox.
• When reinstalling the G1/4" nut, use a new G1/4"
gasket. (Photos 11-2 and 11-4)
(6) Remove the manometer from the manometer cover while
pressing on the claws. (Photo 11-3) Claw
• When reinstalling the manometer assembly on the Photo 11-2 (E*S* series)
hydrobox beware not to put strain on the root of the
capillary tube as the capillary tube is easy to break at Flare nut Gasket (G1/4") Nut (G1/4")
the root.
<Pressure relief valve (3 bar)>

(3) Remove the field piping from the pressure relief valve.
(4) Remove the manometer by removing the G1/4" nut.
• When reinstalling the G1/4" nut, use a new G1/4"
gasket. (Photo 11-2)
(5) Remove the pressure relief valve with a flare joint using
2 spanners: one to hold the flare joint and the other to
turn the flare nut. (Photo 11-2)
(6) Remove the flare joint from the pressure relief valve
using 2 spanners: one to hold the flare joint and the
other to turn the pressure relief valve. (Photo 11-5)
(7) Eliminate loctite on the thread surfaces using remover.
(Photo 11-5)
• Before reinstallation, apply loctite over the thread
Flare joint Capillary tube Pressure relief valve (3 bar)
surface on the pressure relief valve.
• For more details about the loctite and the remover,
refer to page 79.
• Suitable drain pipe work should be attached to Photo 11-3 Capillary
pressure relief valve (3 bar). tube
• Make sure to carry out check (turn the cap) on Manometer
pressure relief valve (3 bar). Claw
Claw
Photo 11-4 (E*PX series)
Gasket (G1/4") Nut (G1/4") Root
Photo 11-5
Flare joint
Pressure relief valve
Threads for application

of loctite
OCH712C 73
11. How to remove the manometer/ pressure relief valve/ air
vent (automatic) (Continued) Photo 11-6
Expansion vessel Pressure relief valve (5 bar)
<Pressure relief valve (5 bar)>
(3) Remove the right side panel.
(4) Remove the band at the base of the pressure relief valve
(5 bar).
(5) Remove the pressure relief valve with a flare joint using
2 spanners: one to hold the flare joint and the other to
turn the flare nut. (Photo 11-6)
(6) Remove the flare joint from the pressure relief valve
using 2 spanners: one to hold the flare joint and the Flare joint
other to turn the pressure relief valve. (Photo 11-6)
(7) Eliminate loctite on the thread surfaces using remover. Band
(Photo 11-6)
• Before reinstallation, apply loctite over the thread Flare nut
surface on the pressure relief valve.
• For more details about the loctite and the remover,
refer to page 79.
• The outlet for the pressure relief valve (5 bar) should
be open ended and facing the rear panel.
Photo 11-7
<Air vent (automatic)>
(3) Remove the air vent with a flare joint using 2 spanners: Expansion vessel Air vent
one to hold the flare joint and the other to turn the flare
nut. (Photo 11-7)
(4) Remove the flare joint from the air vent using 2 spanners:
one to hold the air vent and the other to turn the flare
joint. (Photo 11-8)
Photo 11-8 Flare joint

Flare joint
Air vent Flare nut
12. How to remove the expansion vessel Photo 12-1

(1) Remove the front panel. (Refer to Procedure 1.) Screws Metal support
(2) S
(3) Remove the flare nut using 2 spanners: one to hold the
flare joint and the other to turn the flare nut. (Photo 12-1)
(4) Remove the 2 screws on the metal support.
Note: To avoid dropping of the expansion vessel, hold
the expansion vessel with the metal support by
hand when removing the last screw.
(5) Pull out the metal support. (Photo 12-1)
(6) Pull out the expansion vessel. (Photo 12-1)
(7) Remove the flare joint from the expansion vessel.
(Photo 12-2) Photo 12-2 Expansion vessel Flare joint Flare nut
• When reinstalling the flare joint, use a new G3/8" gasket.
Note: To avoid dropping of the expansion vessel, hold it

securely when removing it.
Gasket G3/8"
OCH712C 74
13. How to remove the drain cock/ the air vent (manual) (pri-
mary circuit). Photo 13 (E*S* series)
(2) S
(3) R
emove the drain cock. and the air vent (manual)
(primary circuit). (Photo 13)
Drain cock
14. How to remove the thermistor <liquid refrigerant temp.> Photo 14-1
(TH2)/ thermistor <flow water temp. & return water temp.>
(THW1, THW2)
(2) D isconnect the CN21 connector and the CNW12 connec-
tor on the controller board. (Photo 14-1)
(3) Release the TH2, THW1 and THW2 lead wires from the
cable strap, the fastener and the coated clamp. (Photo
14-1)
(4) S wing the control box to the front. (Refer to Procedure 4.)
(5) R emove the thermistors from the thermistor holders.
(Photos 14-2, 14-3, 14-4, 14-5 and 14-6)
Connectors
Photo 14-2 (EHS* series) (CN21)
(CNW12)
Cable strap Fastener

Photo 14-4 (E*SE series)
TH2 thermistor THW2 thermistor THW1 thermistor
Note: The photo shown is of the EHSD series.
Photo 14-3 (ERS* series)
THW1
thermistor
TH2 thermistor THW2 thermistor

Photo 14-5 Photo 14-6
(EHPX series) (ERPX series)
THW1
thermistor
THW2
THW2 thermistor TH2 thermistor THW1 thermistor thermistor
Note: The photo shown is of the ERSC series.
THW1 THW2
thermistor thermistor
OCH712C 75
15. How to remove the drain pan <ER** series> Photo 15-1 Claw Screw
(2) Disconnect all the field piping.
(3) Remove the screw on the manometer cover, then hold
the sides of the manometer cover, disengage the 2 claws,
Manometer
and remove the manometer with cover. (Photo 15-1)
(4) Remove the saddle band and the rubber tube by
removing the 2 screws on the saddle band. (Photo 15-2)
• Reuse the removed saddle band, rubber tube and screws
fixing the saddle band and rubber tube. Manometer
(5) Remove the 3 screws each on the cover plate. (Photos cover
15-3 and 15-4)
(6) <ERS* series>
Remove the cover plate from the base assy. (Photo 15-5)
<ERPX series>
Claw
Remove the 2 cover plates from the base assy. (Photo 15-6)
Photo 15-2 (ERS* series)
Strainer valve Strainer valve stay
Screws
Saddle
band Screws Strainer valve holder
Rubber
tube
Photo 15-3 (ERS* series) Photo 15-4 (ERPX series)
Cover plate
Cover plate
Screws Screws Screws
Photo 15-5 (ERS* series) Photo 15-6 (ERPX series)

Base assy
Base assy
Cover plate Cover plate
OCH712C 76
15. How to remove the drain pan <ER** series>
(7) Remove the 3 screws each on the side panel (L, R). Then
remove the 2 screws on the base assy. (Photo 15-7)
(8) Remove the 5 screws on the base assy. (Photo 15-8)
(9) Remove the drain pan from the base assy. (Photo 15-9)
(10) <Only ERS* series>
Remove the strainer valve holder by removing the 2
screws from the drain pan. (Photo 15-10)
• Reuse removed the strainer valve holder and the screws.
Photo 15-8 Base assy

Photo 15-7
Side
panel (R)
Side Screws
panel (L)
Screws
Screws
Screws
Photo 15-9 Drain pan Base Photo 15-10 (ERS* series)
Drain pan
Strainer Strainer valve

valve holder holder fixing
screws
OCH712C 77
16. How to detach and attach the quick joint Photo 16-1
Refer to the following steps when detaching and attaching the
quick connection.
(1) Remove the clip. (Photos 16-1 and 16-2)
(2) Separate the connected parts to remove the O-ring. (Photo
16-3)
• Do not reuse the removed O-ring.
• Wipe off if dirt or foreign matters are found on the sealing Clip
surface where the O-ring touches.
(3) Apply grease on the O-ring using a plastic bag, etc. (Photo
16-4)
(4) Attach the O-ring to the male part of quick connection.
(Photo 16-5)
• Keep the O-ring free from dirt or foreign matters.
(5) C onnect the male and female parts of the quick connection. Photo 16-2 Clip
(Photo 16-6)
(6) Attach the clip. (Photo 16-7)
• Ensure to attach the wider diameter of the clip to the fe-
male side. Failure to do so, it may cause water leak at the
connected part. (Photo 16-8) (For the same diameter
quick connection, following this note is not necessary.)
Photo 16-3 Photo 16-4 Photo 16-5
O-ring
Plastic
bag
O-ring
Female Male
Photo 16-6 Photo 16-7 Photo 16-8
Gap
Clip
OCH712C 78
Notes on replacing the parts
Replacement of the parts listed below requires the following procedure.
After the parts are removed, eliminate loctite on threads by applying loctite remover, apply new loctite, and then install and tight-
en the parts to the specified tightening torques below. For details about recommended loctite and loctite remover, refer to Table
11-1, and for details about the replacement parts and their tightening torques, refer to Table 11-2.
Table 11-1
Recommended Manufacturer No. Note
Loctite Henkel Loctite 5400 Apply loctite all over from the end of external thread
to the second ridge. After installing the parts, fix the
parts for at least 30 minutes
Loctite remover Henkel Loctite 7200 Gasket Remover Spray loctite remover over sealant on the threads,
let the sealant sit until soft, and then eliminate it
with a wire brush.
Note: When using the products above, refer to the appropriate manuals that come with the individual products.
Table 11-2
Part name *1 Recommended tightening torque [Nm] *2
Pressure relief valve (3 bar) 15 ± 1
Pressure relief valve (5 bar) 15 ± 1
*1 For more details about the listed parts, refer to the parts catalogue.
*2 Undertightening and overtightening the parts affect water seal life. Tighten the parts to the appropriate tightening torques.
When installing the parts that are not listed above, observe the tightening torques in accordance with Table 11-3.
Always use a new O-ring or gasket.
Table 11-3
Size [inch] Recommended tightening torque [Nm]
Gasket G1/4" 8±1
G3/8" 15 ± 1
G1" 42 ± 2
G1-1/2" 42 ± 2
Packing Strainer cover 40 ± 2
O-ring Flow sensor 30 ± 2
Air vent (Automatic) 15 ± 1
Attached packing Drain cock (primary circuit) 0.25 ± 0.05
Air vent (manual) 0.25 ± 0.05
Flare joint (for water circuit parts) 35 ± 2
After the procedure is complete, ensure that no water leaks.
OCH712C 79
12 SUPPLEMENTARY INFORMATION
12-1. Refrigerant collecting (pumpdown) for split model systems only
Refer to “Refrigerant collection” in the outdoor unit installation manual or service manual.
12-2. Back-up operation of boiler

Heating operation is backed up by boiler.
For more details, refer to the installation manual of PAC-TH012HT(L)-E.
<Installation & System set up>

1. Set DIP-SW 1-1 to ON "With boiler" and SW2-6 to ON “With Mixing tank”.
2. Install the thermistors THWB1 (Flow temp.) *1 on the boiler circuit.
3. Connect the output wire (OUT10: Boiler operation) to the signal input (room thermostat input) on the boiler. *2
4. Install one of the following room temp. thermostats. *3
Wireless remote controller (option)

Room temp. thermostat (local supply)
Main remote controller (remote position)
*1 The boiler temperature thermistor is an optional part.

*2 OUT10 has no voltage across it.
*3 Boiler heating is controlled on/off by the room temp. thermostat.
<Remote controller settings>

1. Go to Service menu > Heat source setting and choose “Boiler” or “Hybrid”. *4
2. Go to Service menu > Operation settings > Boiler settings to make detailed settings for “Hybrid” above.
*4 The “Hybrid” automatically switches heat sources between Heat pump (and Electric heater) and boiler.
12-3. Multiple outdoor units control

To realize bigger systems by using multiple outdoor units, up to 6 units of the same model can be connected.
The hydrobox can be used as a sub unit for multiple outdoor unit control.
For more details, refer to the installation manual of PAC-IF071/072B-E.
Check the model name of connecting main unit.
<DIP switch setting>

• Set DIP SW4-1 to ON “Active: multiple outdoor unit control”.
• Keep DIP SW4-2 OFF (default setting) (main/sub setting: sub).
• Set DIP SW1-3 to ON when the hydrobox is connected to a DHW tank.
OCH712C 80
13 SERVICE AND MAINTENANCE
13-1. Annual Maintenance
It is essential that the hydrobox is serviced at least once a year by a qualified individual. Any required parts MUST be purchased from Mitsubishi Electric (safety matter).
NEVER bypass safety devices or operate the unit without them being fully operational.
Note
▪ Within the first couple of months of installation, remove and clean the hydrobox’s strainer plus any additional filter items that are fitted external to
the hydrobox. This is especially important when installing on an old/existing pipe work system.
▪ The pressure relief valve (No. 10 on Figure 3.3) should be checked annually by turning the knob manually so that the medium is discharged, thus
cleaning the seal seat.
In addition to annual servicing it is necessary to replace or inspect some parts after a certain period of system operation. Please see tables below for detailed in-
structions. Replacement and inspection of parts should always be done by a competent person with relevant training and qualifications.
Parts which require regular replacement Parts which require regular inspection
Parts Replace every Possible failures Parts Check every Possible failures
Pressure relief valve (PRV) Pressure relief valve (3 bar) 1 year PRV would be fixed and
Air vent (Auto/ Manual) 6 years Water leakage Temperature and pressure (turning the knob expansion vessel would
Manometer relief valve manually) burst
Earth leakage causing
Immersion heater 2 years circuit breaker to activate
(Heater is always OFF)
Water circulation pump Water circulation pump
20,000 hrs (3 years)
(Primary circuit) failure
Parts which must NOT be reused when servicing
* O-ring
* Gasket
Note:
• Always
replace the gasket for pump with a new one at each regular main-
tenance (every 20,000 hours of use or every 3 years).
• No need to inspect pressure relief valve (5 bar) because it does not con-
tact with water unless 3 bar PRV is broken.
13-2. Engineers Forms
Should settings be changed from default, please enter and record new setting in ‘Field Setting’ column. This will ease resetting in the future should the system use
change or the circuit board need to be replaced.
Commissioning/Field settings record sheet
Main remote controller screen Parameters Default setting Field setting Notes
Main Zone1 heating room temp. 10°C to 30°C 20°C
Zone2 heating room temp. *1 10°C to 30°C 20°C
Zone1 heating flow temp. 20°C to 60°C 45°C
Zone2 heating flow temp. *2 20°C to 60°C 35°C
Zone1 cooling flow temp. *3 5°C to 25°C 15°C
Zone1 heating compensation curve −9°C to + 9°C 0°C
Zone2 heating compensation curve *2 −9°C to + 9°C 0°C
Holiday mode Active/Non active/Set time —
Option Forced DHW operation On/Off —
DHW On/Off/Timer On
Heating/Cooling On/Off/Timer On
Energy monitor Consumed electrical energy/Delivered energy —
Setting DHW *4 Operation mode Normal/Eco *5 Normal
DHW max. temp. 40°C to 60°C *6 50°C
DHW temp. drop 5°C to 30°C 10°C
DHW max. operation time 30 to 120 min 60 min
DHW mode restriction 30 to 120 min 30 min
DHW recharge Large/Standard Large *7
Legionella prevention *4 Active Yes/No Yes
Hot water temp. 60°C to 70°C *6 65°C
Frequency 1 to 30 days 15 days
Start time 00.00 to 23.00 03.00
Max. operation time 1 to 5 hours 3 hours
Duration of maximum temp. 1 to 120 min 30 min
Heating/ Cooling *3 Zone1 operation mode Heating room temp./ Heating flow temp./ Heating Room temp.
compensation curve/ Cooling flow temp.
Zone2 operation mode *2 Heating room temp./ Heating flow temp./ Heating Compensation curve
compensation curve/ Cooling flow temp.
Compensation Hi flow temp. Zone1 outdoor ambient temp. −30°C to +33°C *8 −15°C
curve set point Zone1 flow temp. 20°C to 60°C 50°C
Zone2 outdoor ambient temp. *2 −30°C to +33°C *8 −15°C
Zone2 flow temp. *2 20°C to 60°C 40°C
Lo flow temp. Zone1 outdoor ambient temp. −28°C to +35°C *9 35°C
set point Zone1 flow temp. 20°C to 60°C 25°C
Zone2 outdoor ambient temp. *2 −28°C to +35°C *9 35°C
Zone2 flow temp. *2 20°C to 60°C 25°C
Adjust Zone1 outdoor ambient temp. −29°C to +34°C *10 —
Zone1 flow temp. 20°C to 60°C —
Zone2 outdoor ambient temp. *2 −29°C to +34°C *10 —
Zone2 flow temp. *2 20°C to 60°C —
Holiday DHW *4 Active/Non active Non active
Heating/ Cooling *3 Active/Non active Active
Zone1 heating room temp. 10°C to 30°C 15°C
Zone2 heating room temp. *1 10°C to 30°C 15°C
Zone1 heating flow temp. 20°C to 60°C 35°C
Zone2 heating flow temp. *2 20°C to 60°C 25°C
(Continued to next page.)
OCH712C 81
Engineers Forms
Commissioning/Field settings record sheet (continued from the previous page)
Parameters Field
Main remote controller screen Default setting Notes
setting
Setting Initial settings Language EN/FR/DE/SV/ES/IT/DA/NL/FI/NO/PT/BG/PL/CZ/RU/ EN
TR/SL
°C/°F °C/°F °C
Summer time On/Off Off
Temp. display Room/DHW tank/Room&DHW tank /Off Off
Time display hh:mm/hh:mm AM/AM hh:mm hh:mm
Room sensor settings for Zone1 TH1/Main RC/Room RC1-8/“Time/Zone” TH1
Room sensor settings for Zone2 *2 TH1/Main RC/Room RC1-8/“Time/Zone” TH1
Room RC zone select *2 Zone1/Zone2 Zone1
Service menu Thermistor adjustment THW1 −10°C to +10°C 0°C
THW2 −10°C to +10°C 0°C
THW5B −10°C to +10°C 0°C
THW6 −10°C to +10°C 0°C
THW7 −10°C to +10°C 0°C
THW8 −10°C to +10°C 0°C
THW9 −10°C to +10°C 0°C
THW10 −10°C to +10°C 0°C
THWB1 −10°C to +10°C 0°C
Auxiliary settings Economy settings On/Off *11 On
for pump. Delay (3 to 60 min) 10 min
Electric heater Space heating: On (used)/Off (not used) On
(Heating) Electric heater delay timer (5 to 180 min) 30 min
Electric heater Booster heater DHW: On (used)/Off (not used) On
(DHW) *4 Immersion heater DHW: On (used)/Off (not used) On
Electric heater delay timer (15 to 30 min) 15 min
Mixing valve control Running (10 to 240 sec) 120 sec
Interval (1 to 30 min) 2 min
Flow sensor *12 Minimum (0 to 100 L/min) 5 L/min
Maximum (0 to 100 L/min) 100 L/min
Analog output Interval (1 to 30 min) 5 min
Priority (Normal/High) Normal
Pump speed DHW Pump speed (1 to 5) 5
Heating/Cooling Pump speed (1 to 5) 5
Heat source setting Standard/Heater/Boiler/Hybrid *13 Standard
Heat pump setting Heat pump flow rate range Minimum (0 to 100 L/min) 5 L/min
Maximum (0 to 100 L/min) 100 L/min
Quiet mode Day (Mon to Sun) —
Time 0:00 - 23:45
Quiet level (Normal/ Level1/ Level2) Normal
Operation Heating Flow temp.range Min.temp.(20 to 45°C) 30°C
settings operation *14 Max.temp.(35 to 60°C) 50°C
Room temp. Mode(Normal/Fast) Normal
control Interval(10 to 60 min) 10 min
*15
Heat pump thermo On/Off *11 On
diff.adjust Lower limit (−9 to −1°C) −5°C
Upper limit (+3 to +5°C) 5°C
Freeze stat function *16 Outdoor ambient temp. (3 to 20°C) / ** 5°C
Simultaneous operation (DHW/ On/Off *11 Off
Heating) Outdoor ambient temp. (−30 to +10°C) *8 −15°C
Cold weather function On/Off *11 Off
Outdoor ambient temp. (−30 to −10°C) *8 −15°C
Boiler operation Hybrid settings Outdoor ambient temp. −15°C
(−30 to +10°C) *8
Priority mode Ambient
(Ambient/Cost/CO2) *17
Outdoor ambient temp. rise +3 °C
(+1 to +5 °C)
Intelligent Energy Electricity (0.001 to 999 */kWh) 0.5 */kWh
settings price Boiler (0.001 to 999 */kWh) 0.5 */kWh
*18
CO2 Electricity 0.5 kg -CO2/
emis- (0.001 to 999 kg -CO2/kWh) kWh
sion Boiler 0.5 kg -CO2/
(0.001 to 999 kg -CO2/kWh) kWh
Heat Heat pump capacity 11.2 kW
source (1 to 40 kW)
Boiler efficiency 80%
(25 to 150%)
Booster heater 1 capacity 2 kW
(0 to 30 kW)
Booster heater 2 capacity 4 kW
(0 to 30 kW)
(Continued to next page.)
OCH712C 82
Engineers Forms
Commissioning/Field settings record sheet (continued from the previous page)
Default Field
Main remote controller screen Parameters setting setting Notes
Service menu Operation Smart grid ready DHW On/Off Off
settings Target temp(+1 to +20°C) / -- (Non active) --
Heating On/Off Off
Target temp. Switch-on recommendation (20 to 60°C) 50°C
Switch-on command (20 to 60°C) 55°C
Cooling On/Off Off
Target temp. Switch-on recommendation (5 to 25°C) 15°C
Switch-on command (5 to 25°C) 10°C
Pump cycles Heating (On/Off) On
Cooling (On/Off) On
Interval (10 to 120 min) 10 min
Floor dry up function On/Off *11 Off
Target temp. Start&Finish (20 to 60°C) 30°C
Max. temp. (20 to 60°C) 45°C
Max. temp. period (1 to 20 days) 5 days
Flow temp. Temp. increase step (+1 to +10°C) +5°C
(Increase) Increase interval (1 to 7 days) 2 days
Flow temp. Temp. decrease step (−1 to −10°C) −5°C
(Decrease) Decrease interval (1 to 7 days) 2 days
Summer mode On/Off Off
Outdoor ambi- Heating ON (4 to 19°C) 10°C
ent temp. Heating OFF (5 to 20°C) 15°C
Judgement Heating ON (1 to 48 hours) 6 hours
time Heating OFF (1 to 48 hours) 6 hours
Forced heating ON (-30 to 10°C) 5 °C
Water flow control On/Off Off
Energy Electric heater Booster heater 0 to 30 kW 2 kW
monitor capacity 1 capacity
settings Booster heater 0 to 30 kW 4 kW
2 capacity
Immersion 0 to 30 kW 0 kW
heater capacity
Analog output 0 to 30 kW 0 kW
Delivered energy adjustment −50 to +50% 0%
Water pump input Pump 1 0 to 200 W or ***(factory fitted pump) ***

Pump 2 0 to 200 W 0W
Pump 3 0 to 200 W 0W
Pump 4 *7 0 to 200 W 72 W
Electric energy meter *19 0.1/1/10/100/1000 pulse/kWh 1000 pulse/kWh
Heat meter *19 0.1/1/10/100/1000 pulse/kWh 1000 pulse/kWh
External in- Demand control (IN4) Heat source OFF/Boiler operation Boiler
put settings operation
Outdoor thermostat (IN5) Heater operation/Boiler operation Boiler
operation
Thermo ON output Zone1/Zone2/Zone1&2 Zone1&2
*1 The settings related to Zone2 can be switched only when 2-zone temperature control or 2-zone valve ON/OFF control is active.
*2 The settings related to Zone2 can be switched only when 2 Zone temperature control is enabled (when DIP SW2-6 and SW 2-7 are ON).
*3 Cooling mode settings are available for ERS* model only.
*4 Only available if DHW tank present in system.
*5 When the hydrobox is connected with a PUMY-P outdoor unit, the mode is fixed to “Normal”.
*6 For the model without both booster and immersion heater, it may not reach the set temperature depending on the outside ambient temperature.
*7 This setting is valid for only cylinder units.
*8 The lower limit is -15°C depending on the connected outdoor unit.
*11 On: the function is active; Off: the function is inactive.
*12 Do not change the setting since it is set according to the specification of flow sensor attached to the hydrobox.
*13 When DIP SW1-1 is set to OFF “WITHOUT Boiler” or SW2-6 is set to OFF “WITHOUT Mixing tank”, neither Boiler nor Hybrid can be selected.
*14 Valid only when operating in Heating room temperature.
*15 When DIP SW5-2 is set to OFF, the function is active.
*16 If asterisk (**) is chosen freeze stat function is deactivated. (i.e. primary water freeze risk)
*17 When the hydrobox is connected with a PUMY-P outdoor unit, the mode is fixed to “Ambient”.
*18 “*” of “*/kWh” represents currency unit (e.g. € or £ or the like)
*19 The default setting is 1 pulse/kWh depending on the connected indoor unit.
OCH712C 83
13-3. Annual Maintenance Log Book
Contractor name Engineer name
Site name Site number
Hydrobox maintenance record sheet

Warranty number Model number
Serial number
No. Mechanical Frequency Notes
Isolate and drain hydrobox, remove mesh from internal strainer clean and
1
replace.
Open the pressure relief valve, check for unrestricted discharge to
2 the tundish and that the valve reseats correctly. Check there are no
blockages in the tundish and associated pipe work.
Drop the primary/heating system pressure to zero check and if necessary
3 top up the expansion relief vessel (1 bar). Air valve of expansion vessel
is TR-412.
Check and if necessary top up the concentration of anti-freeze/inhibitor (if
4
used in the system).
Top up the primary/heating system using an appropriate filling loop and
5
re-pressurise to 1 bar.
Heat system and check pressure does not rise above 3 bar and no water
6
is released from the safety valves.
7 Release any air from the system.
Refrigerant models only Frequency Notes
1 Refer to outdoor unit manual.
Electrical Frequency Notes
1 Check condition of cables.
2 Check rating and fuse fitted on the electricity supply.
Controller Frequency Notes
1 Check field settings against factory recommendations.
2 Check battery power of wireless thermostat and replace if necessary.
Outdoor heat pump unit maintenance record sheet
Model number Serial number
Mechanical Frequency Notes
1 Inspect grill, heat exchanger fins and air inlet for trapped debris/damage.
2 Check condensate drain provision.
3 Check integrity of water pipe work and insulation.
4 Check all electrical connections.
5 Check and record the operation voltage.
All the above checks should be carried out once a year.
Note:
Within the first couple of months of installation, remove and clean the hydrobox’s strainer mesh plus any that are fitted external to the hydrobox. This is
especially important when installing on an existing system.
In addition to annual servicing it is necessary to replace or inspect some parts after a certain period of system operation. Please see tables below for detailed instruc-
tions. Replacement and inspection of parts should always be done by a competent person with relevant training and qualifications.
Parts which require regular replacement Parts which require regular inspection
Parts Replace every Possible failures Parts Check every Possible failures
Pressure relief valve (3 bar) Pressure relief valve 1 year (turning the PRV would be fixed and
Air vent (Auto/ Manual) (3 bar) knob manually) expansion vessel would
6 years Water leakage
Drain cock (Primary circuit) burst
Manometer Water circulation pump
Water circulation pump 20,000 hrs (3 years)
failure
Parts which must NOT be reused when servicing

* O-ring
* Gasket
Note:
lways replace the gasket for pump with a new one at each regular maintenance (every 20,000 hours of use or every 3 years).
•A
ake sure to carry out annual check (turn the cap) on 3 bar PRV. This is not required for 5 bar PRV.
•M
OCH712C 84
OCH712C 85
HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Copyright 2019 MITSUBISHI ELECTRIC CORPORATION

Issued: Oct. 2020 No. OCH712 REVISED EDITION-C
Issued: Apr. 2020 No. OCH712 REVISED EDITION-B
Issued: Feb. 2020 No. OCH712 REVISED EDITION-A
Published: Oct. 2019 No. OCH712
Made in Japan Specifications are subject to change without notice.

Service Manual PT

Uploaded by

Copyright:

Available Formats

Service Manual PT

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual PT

Uploaded by

Copyright:

Available Formats

HYDROBOX

EHSD-TM9D EHSC-TM9D EHPX-VM6D OCH712B is void.

ERSD-MED ERSC-MED EHPX-YM9D Note:

MAIN REMOTE 12. SUPPLEMENTARY INFORMATION.............. 80

PARTS CATALOG (OCB712)

OUTDOOR UNIT'S SERVICE MANUAL

Mitsubishi Electric is not responsible for the failure of locally-supplied parts.

• Be sure to perform periodical maintenance.

MEANINGS OF SYMBOLS DISPLAYED ON THE UNIT

Read the OPERATION MANUAL carefully before operation.

[1] Cautions for service

[2] Additional refrigerant charge

Electronic weighing scale

[3] Service tools

Overall unit dimensions (Height × Width × Depth) 800 × 530 × 360 mm

range Heating 10 - 30°C

<E*S*-*M**D> (Split model system) <E*SE-*M*ED> (Split model system)

<Figure 4.3> <Figure 4.4>

EARTH LEAKAGE BREAKER

BACK PANEL SUPPORT

PRESSURE RELIEF VALVE

<Front> <Side> <Rear>

<View from below> <View from below>

AUTO AIR VENT

EARTH LEAKAGE BREAKER

BACK PANEL SUPPORT

<Front> <Side> <Rear>

PIPE. (FLARING) 3/4F REFRIGERANT (GAS)

<View from below>

TAB1 CN401 CNW5 CNW12 CN21 CN20

THW5B THW1 THW2 TH2 TH1

Table 1 Signal Inputs

(thermo on) 4 LED2 5

6 8 CN105 WiFi adapter

TAB1 CN401 CNW5 CNW12 CN21 CN20

THW5B THW1 THW2 TH2 TH1

Table 1 Signal Inputs

BU CNPWM (BU) 3 OG (BU) 3 OG

TAB1 CN401 CNW5 CNW12 CN21 CN20

THW5B THW1 THW2 TH2 TH1

Table 1 Signal Inputs

BHC1 BHC2 X5B 1 1

TAB1 CN401 CNW5 CNW12 CN21 CN20

THW5B THW1 THW2 TH2 TH1

Table 1 Signal Inputs

BHC1 BHC2 X5B 1 1

TAB1 CN401 CNW5 CNW12 CN21 CN20

THW5B THW1 THW2 TH2 TH1

Table 1 Signal Inputs

Option1: Hydrobox powered via outdoor unit

Earth Wiring To control

<3 phase> Hydrobox

Wiring No. Hydrobox - Outdoor unit *3 3 × 1.5 (polar)

<E*S*> (Split model system) Refrigerant flow

2-zone temperature control 1-zone temperature control with boiler

Draining the Hydrobox

*1 When the system is switched off or the power supply is disconnect-

‘Quiet mode’ is activated.

12 15 14 11 1 17 2 3 16 3 Electric heater When this icon is displayed, the ‘Electric heaters’

<ES-*M**D> (Split model system) <ESE-M*ED> (Split model system)

<ES> (Split model system) Refrigerant flow

*1 When the system is switched off or the power supply is disconnect-

• If no problem found with the wiring, go to 3. below.