RESEARCH&DEVELOPMENT OF AMERICA, INC.

5420 DANIELS STREET STE A, CHINO CA., 91710 · (800)634-9166 · (909)628-4722 · FACSIMILE (909)591-2198
www.yoshimura-rd.com

FENDER ELIMINATOR KIT

070BG125511
Honda CBR500R

THIS PRODUCT IS NOT DOT APPROVED.

Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the
! installation of this product. Check with local laws and regulations for compliance prior to
installation and use. This product is not intended for use on public highways. !
 Assembly Diagram

10 11
2
1
7 6
9
5

10

8
4
3 11

No. Item Description Qty.

1 12551-FEBKT Fender Eliminator Bracket 1
2 070BG-LH-K1 LED License Plate Light 1
3 070BG-LPF License Plate Frame 1
4 12200-TSB-L Left Turn Signal Bracket 1
5 12200-TSB-R Right Turn Signal Bracket 1
6 M6X20BHS 6mm x 20mm Button Head Screw 4
7 M6X16BHS 6mm x 16mm Button Head Screw 2
8 M6X14BHS 6mm x 14mm Button Head Screw 2
9 M4X6BHS 4mm x 6mm Button Head Screw 2
10 6MMWASHER 6mm Washer 8
11 6MMLN 6mm Nylon Lock Nut 8
** BN-SSS-22-18 Butt Connectors 2
** ZT-400 Cable Ties 3
** 17029 Yoshimura Sticker Sheet 1
Optional Parts
*** 070BGUNVTBKT Universal Turn Signal Bracket Kit
** Not shown on diagram.
*** The Yoshimura Universal Turn Signal Bracket Kit is to be used with aftermarket stud-mounted turn signals and is sold separately.

2
 Removal Scan for link to butt connector instruction video

1. Remove passenger seat.

2. Locate and disconnect license plate light and

turn signal connectors.

3. While securely supporting the stock fender 3. Secure and install (No. 1) 12551-FEBKT, fender
assembly, remove the four bolts securing the eliminator bracket to subframe using (No. 6)
fender assembly to the subframe. Carefully M6X20BHS, 6mm button head screws from
remove the stock fender assembly making sure below and install (No. 10,11) 6MMWASHER
not to damage connectors in the process. and 6MMLN, 6mm washer and nut from above
as shown.
4. Remove left and right turn signals from the
stock fender assembly.
10 11
5. Cut the stock license plate light connector from
the stock fender assembly. Be sure to cut at
least a 6” section of wire from the connector.

6
Installation 1

1. Install (No. 2) 070BG-LH-K1, license plate light 4. Install stock rear turn signals onto (No. 4,5)
onto (No. 1) 12551-FEBKT, fender eliminator 122000-TSB-L/R, left and right turn signal
bracket using (No. 9) M4X6BHS, 4mm screws. brackets using the stock hardware.

2 5. Install (No. 4,5) 12200-TSB-L/R, left and right

9 turn signal brackets and (No. 3) 070BG-LPF,
license plate frame to (No. 1) 12551-FEBKT,
fender eliminator bracket using the (No. 7,8)
M6X16BHS and M6X14BHS, 6mm button head
1 screws and (No. 10,11) 6MMWASHER,
6MMLN, washer and nut as shown.
2. Using the BN-SSS-22-18 butt connectors
1
provided in the kit, connect the Yoshimura
license plate light wires to the stock license
plate light wires as follows: 7
5
Red -to- Orange 11
Black -to- Green 8
a) Strip the stock fender light wire ends 3 10
1/4” - 1/2” and insert into BN-SSS-22-18, 4
butt connectors provided in the kit.
b) Center the spliced wire ends in the
middle and using a heatgun or lighter,
apply heat evenly on the outer edges of 6. Route license plate light and turn signal wires
the butt connector to shrink and hold through the hole in (No. 1) 12551-FEBKT,
wires in place. fender eliminator bracket and through the lower
c) Making sure that the stripped ends are rear cowl. Re-connect license plate light and
centered, heat the center of the butt turn signal connectors.
connector evenly until the solder begins
to liquify. 7. Use the cable ties supplied in the kit to secure
d) Allow to cool completely and tug both license plate light and turn signal wires.
ends of the wires to verify that connection
is secured. 8. Re-install passenger seat.

3
9. Check for proper function of license plate light
and turn signals and that all brackets and
components are secure prior to riding.