Scribd
Upload
21 views5 pages

PHOTOPRINT

This document provides step-by-step instructions for creating an ICC output profile in a third-party color profiler. It describes setting printer options, performing ink limit, linearization and multi-ink limit tests, characterizing the printer, and generating the ICC profile.

Uploaded by

Mohammad yusufm
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
21 views5 pages

PHOTOPRINT

This document provides step-by-step instructions for creating an ICC output profile in a third-party color profiler. It describes setting printer options, performing ink limit, linearization and multi-ink limit tests, characterizing the printer, and generating the ICC profile.

Uploaded by

Mohammad yusufm
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

PhotoPRINT: Create ICC Output Profile in 3rd party profiler

 Set the Default job Properties.


1. Make sure “No color correction”, then select the desired resolution,
printing type and color mode.

2． Set the desired printer options.

 Set the profiler setup.

 Start the color profiler


PhotoPRINT: Create ICC Output Profile in 3rd party profiler
Tips：1. Input the media display name and file name.
2. If you create the profile for grayscal printing, select the “Enable gray
balance”.
If for color printing, leave this option unchecked.
3. Click the save then next.

 Ink Limit
1. Click the “Print ink limit test”, then a file will be printed on your printer.

2. According to the printed test chart, Check the print for bleeding and over
saturation of ink.

3. Input the ink limit


1. Select the channel and set by experience: Up the point of one to 55%
vertically and drag the 2, 3 point to limiting case.
2. Print an ink split to verification test to verify that your settings are correct.

3. After adjusted, Click save and next.


4. Click the save then next.
Tips: If you have selected a CMYK printing mode you’ll go direct to the
Linearization step.
 Linearization
 Ink Split
The step only appear If your printer working in 6 ,7 or more color mode and
using the light and dark inks, for example :CMYKLcLm. The Ink Split let the
ink from light to dark more nature.
PhotoPRINT: Create ICC Output Profile in 3rd party profiler

1. Connect the spectrophotometer to the use port of computer.


2. Select the increment size.

Tips: 1. Check the curves, the curves should smooth, If have too much up or down,
you should measure it again.
2. The red 1 in picture have an error, you should measure it again and the
curve red 2 arrive the max ink too early. You should go back to step of Ink

Tips: limit and limit the black ink more.


If your printer state is better, you can select the 5% or Enhanced, 3. The channels of cyan and magenta were too low in the area of light ink. You
If your printer state is bad, select the 10%.
3. Click Print Target, then a file will be printing. should go back to the step of ink split.
4. Click save and next.

4. Click , and start measure.

5. Click ,and look at the curves of linearization.


PhotoPRINT: Create ICC Output Profile in 3rd party profiler
Multi-ink Limit 1. Minimize the window of color profiler.

Tips: If the window was closed accidentally or you want to modify the ICC
1.Click ,a file will be printing .
Profile, you should open the main window of color profiler and use

the “Modify or resume ICC profile” option .

2. Check the print for bleeding and over saturation of ink.

rd
2. Add the swatch target of the 3 party profiler to PhotoPRINT and set
3. Input the Multi-ink Limit.
the job properties: Only use the linearization correction and choose the

unfinished ICC profile that you saved in the step of Multi-ink Limit.

4. Print an ink limit verification test to verify that your settings are correct.

5. Click save and next.

Characterization
PhotoPRINT: Create ICC Output Profile in 3rd party profiler
5. Click save and next

 ICC Generation

rd
3. Printing the swatch target of the 3 party profiler, and generate the

ICC profile in the 3rd party Profiler.


rd
4. Maximizing the window of color profiler and click the 3 party ICC button Click the Generate button and finish the creation.
rd
to import the 3 part ICC profile.

You might also like