Scribd
Upload
8 views

Lab Sim

Uploaded by

Msambili Ndaga
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
8 views

Lab Sim

Uploaded by

Msambili Ndaga
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

A network associate is adding security to the configuration of the Corp1 router.

The user on host C


should be able to use a web browser to access financial information from the Finance Web Server. No
other hosts from the LAN nor the Core should be able to use a web browser to access this server.
Since there are multiple resources for the corporation at this location including other resources on the
Finance Web Server, all other traffic should be allowed.

The task is to create and apply a numbered access-list with no more than three statements that will
allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the
Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.

All passwords have been temporarily set to “cisco”.


The Core connection uses an IP address of 198.18.196.65
The computers in the Hosts LAN have been assigned addresses of 192.168.33.1 – 192.168.33.254
Host A 192.168.33.1
Host B 192.168.33.2
Host C 192.168.33.3
Host D 192.168.33.4
The servers in the Server LAN have been assigned addresses of 172.22.242.17 – 172.22.242.30
The Finance Web Server is assigned an IP address of 172.22.242.23.
The Public Web Server is assigned an IP address of 172.22.242.17
Corp1>enable

Corp1#show running-config

We learn that interface FastEthernet0/1 is the interface connected to Server LAN network. It is the
interface we will apply our access-list (for outbound direction).

Corp1#configure terminal

Our access-list needs to allow host C – 192.168.33.3 to the Finance Web Server 172.22.242.23 via
web (port 80)

Corp1(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80

Deny other hosts access to the Finance Web Server via web

Corp1(config)#access-list 100 deny tcp any host 172.22.242.23 eq 80

All other traffic is permitted

Corp1(config)#access-list 100 permit ip any any

Apply this access-list to Fa0/1 interface (outbound direction)

Corp1(config)#interface fa0/1
Corp1(config-if)#ip access-group 100 out

Corp1(config-if)#end
Corp1#copy running-config startup-config
After adding R3 router, no routing updates are being exchanged between R3 and the new location. All
other inter connectivity and Internet access for the existing locations of the company are working
properly.

The task is to identify the fault(s) and correct the router configuration to provide full connectivity
between the routers.

R1 R2

Fa0/0: Fa0/0: 192.168.60.97


192.168.77.33
Fa0/1: 192.168.60.113
S1/0: 198.0.18.6
S0/0: 192.168.36.14
S0/1: 192.168.60.25

S0/0: 192.168.36.13

R3 R4

Fa0/0: Fa0/0: 192.168.60.129


192.168.77.34
Fa0/1: 192.168.60.145
Fa0/1:
192.168.60.65 S0/1: 192.168.60.26

Fa1/0:
192.168.60.81
We should check the configuration of the new added router first because it does not function properly
while others work well. From the command line interface of R3 router, enter the show running-
config command

From the output above, we know that this router was wrongly configured with an autonomous number
(AS) of 22. When the AS numbers among routers are mismatched, no adjacency is formed.

(To solve this problem, we simply re-configure router R3 with the following commands:

R3>enable (you have to enter cisco as its password here)

R3#configure terminal

R3(config)#no router eigrp 22

R3(config)#router eigrp 212

R3(config-router)#network 192.168.60.0

R3(config-router)#network 192.168.77.0

R3(config-router)#no auto-summary

R3(config-router)#end

R3#copy running-config startup-config

Check R1 router with the show running-config command:

Notice that it is missing a definition to the network R3. Therefore we have to add it so that it can
recognize R3 router

R1>enable (you have to enter cisco as its password here)

R1#configure terminal

R1(config)#router eigrp 212

R1(config-router)#network 192.168.77.0

R1(config-router)#end

R1#copy running-config startup-config

You might also like