STRUCTURAL DESIGN CALCULATION FOR

DISTILLATION SKID
“ENGINEERING, PROCUREMENT, CONSTRUCTION AND COMMISSIONING ("EPCC") WORKS FOR AN
INTEGRATED PLANT CONSISTING OF A BASE OIL RE‐REFINING PLANT(OPAL) AND A WASTE OIL
SLUDGE RE‐REFINING PLANT(MAVROS) ("INTEGRATED PLANT")

PLOT 4, CENVIRO ECOPARK (CEP), BUKIT PELANDOK, NEGERI SEMBILAN, MALAYSIA

CENVIRO RECYCLING AND RECOVERY SDN BHD

MUTIARA ETNIK SDN BHD

AUGUST’ 2023

Prepared By:

Meinhardt EPCM
STRUCTURAL DESIGN BRIEF

Structure Design Outline/Specifications

1. Code and Standard

1) Code : Malaysian Building Code (Uniform Building By-. Law)

2) Standards: : BS6399: Design Load
BS8110: Structure Use of Concrete
BS8004: Foundations
BS5950: Structure Use of Steelwork
CP3: Chapter V: Part2 : Wind Load
MS 1553:2002 Wind Load

2. Structure Design Load Condition

1) Wind Load and notional lateral load
Basic Wind Velocity (m/sec) - 33m/s for 3 second gust speed

2)Typical loading :

Location Design Live Load (kN/m2)

Unless Otherwise Stated
Ground Slab 20 kN/m2

3)Roof Loading:

Metal Roofing : 0.05 kPa

Insulation : 0.05 kPa
M&E : 0.25 kPa
Live Load : 0.25 kPa

4)DESIGN LOAD COMBINATION (According to BS 8110-1:1997, Table 2.1)

• 1.4 DL + 1.6 (LL + M&E)

• 1.0 DL + 1.0 (LL + M&E)
• 1.4 DL + 1.4 WL
• 1.2 DL + 1.2 (LL + M&E) + 1.2 WL

**DL = Structure Self Weight + Floor Finishes

**LL = Design Live Load
**WL = Wind Load
3. Structural Material Specification
1) Reinforcement
Grade Min Fy Bar Notation Remarks
460 460N/mm² T10 thru T32 Deformed bars (type 2)
250 250N/mm² R6 thru R16 Plain bars
to conform to BS 4449 or approved equivalent

2) Concrete
Locations 28 Days Strength, fcu
Foundation 35N/mm² (G40)
Beam, Slab 35N/mm² (G35)
Lean Concrete 10N/mm² (G10)
DESIGN CALCULATION & SOFTWARE OUTPUT
Staad 3D Model
Staad Modelling for Foundation Load
 Job No Sheet No Rev
1
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Job Information
Engineer Checked Approved

Name:
Date: 26-Jul-23

Project ID
Project Name

Structure Type SPACE FRAME

Number of Nodes 38 Highest Node 43

Number of Elements 69 Highest Beam 76

Number of Basic Load Cases 2

Number of Combination Load Cases 3

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DL+LL
Primary 2 WL
Combination 3 1.0 DL + LL + WL
Combination 4 1.2 DL + LL + WL
Combination 5 1.5 (DL + LL)

Primary Load Cases

Number Name Type

1 DL+LL None
2 WL None

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

3 1.0 DL + LL + WL 1 DL+LL 1.00

2 WL 1.00
4 1.2 DL + LL + WL 1 DL+LL 1.20
2 WL 1.20
5 1.5 (DL + LL) 1 DL+LL 1.50

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 1 of 52
 Job No Sheet No Rev
2
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
Max FX 42 1:DL+LL 0 283.494 14.059 0 0 0
Min FX 42 1:DL+LL 0 283.494 14.059 0 0 0
Max FY 42 5:1.5 (DL + LL) 0 425.241 21.088 0 0 0
Min FY 42 2:WL 0 -48.952 -57.760 0 0 0
Max FZ 42 5:1.5 (DL + LL) 0 425.241 21.088 0 0 0
Min FZ 43 4:1.2 DL + LL + WL 0 398.935 -83.216 0 0 0
Max MX 42 1:DL+LL 0 283.494 14.059 0 0 0
Min MX 42 1:DL+LL 0 283.494 14.059 0 0 0
Max MY 42 1:DL+LL 0 283.494 14.059 0 0 0
Min MY 42 1:DL+LL 0 283.494 14.059 0 0 0
Max MZ 42 1:DL+LL 0 283.494 14.059 0 0 0
Min MZ 42 1:DL+LL 0 283.494 14.059 0 0 0

Reaction Envelope
Horizontal Vertical Horizontal Moment
Node Env FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
42 +ve 0 425.241 21.088 0 0 0
42 +ve - Load: 5 Load: 5 - - -
42 -ve 0 -48.952 -57.760 0 0 0
42 -ve - Load: 2 Load: 2 - - -
43 +ve 0 425.241 0 0 0 0
43 +ve - Load: 5 - - - -
43 -ve 0 0 -83.216 0 0 0
43 -ve - - Load: 4 - - -

Reactions
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
42 1:DL+LL 0 283.494 14.059 0 0 0
2:WL 0 -48.952 -57.760 0 0 0
3:1.0 DL + LL + WL 0 234.542 -43.701 0 0 0
4:1.2 DL + LL + WL 0 281.451 -52.441 0 0 0
5:1.5 (DL + LL) 0 425.241 21.088 0 0 0
43 1:DL+LL 0 283.494 -14.059 0 0 0
2:WL 0 48.952 -55.288 0 0 0
3:1.0 DL + LL + WL 0 332.446 -69.347 0 0 0
4:1.2 DL + LL + WL 0 398.935 -83.216 0 0 0
5:1.5 (DL + LL) 0 425.241 -21.088 0 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 2 of 52
 Job No Sheet No Rev
3
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Node Displacement Summary

Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Max X 1 1:DL+LL 0 -0.121 -1.421 1.426 -0.001 0 0
Min X 1 1:DL+LL 0 -0.121 -1.421 1.426 -0.001 0 0
Max Y 20 2:WL 0 5.213 100.426 100.561 0.000 0 0
Min Y 5 5:1.5 (DL + LL) 0 -31.846 -0.000 31.846 -0.000 0 0
Max Z 6 4:1.2 DL + LL + WL 0 -0.454 124.988 124.988 0.005 0 0
Min Z 9 5:1.5 (DL + LL) 0 -5.966 -2.963 6.661 0.004 0 0
Max rX 43 4:1.2 DL + LL + WL 0 0 0 0 0.016 0 0
Min rX 36 5:1.5 (DL + LL) 0 -6.700 -1.283 6.822 -0.004 0 0
Max rY 1 1:DL+LL 0 -0.121 -1.421 1.426 -0.001 0 0
Min rY 1 1:DL+LL 0 -0.121 -1.421 1.426 -0.001 0 0
Max rZ 1 1:DL+LL 0 -0.121 -1.421 1.426 -0.001 0 0
Min rZ 1 1:DL+LL 0 -0.121 -1.421 1.426 -0.001 0 0
Max Rst 26 4:1.2 DL + LL + WL 0 -23.880 123.487 125.775 0.002 0 0

Beam End Displacement Summary

Displacements shown in italic indicate the presence of an offset
Beam Node L/C X Y Z Resultant
(mm) (mm) (mm) (mm)
Max X 1 1 1:DL+LL 0 -0.121 -1.421 1.426
Min X 1 1 1:DL+LL 0 -0.121 -1.421 1.426
Max Y 20 20 2:WL 0 5.213 100.426 100.562
Min Y 4 5 5:1.5 (DL + LL) 0 -31.846 0 31.846
Max Z 5 6 4:1.2 DL + LL + WL 0 -0.453 124.988 124.988
Min Z 3 9 5:1.5 (DL + LL) 0 -5.966 -2.963 6.662
Max Rst 26 26 4:1.2 DL + LL + WL 0 -23.880 123.487 125.775

Beam End Force Summary

The signs of the forces at end B of each beam have been reversed. For example: this means that the Min Fx entry gives the largest tension
value for an beam.
Axial Shear Torsion Bending
Beam Node L/C Fx Fy Fz Mx My Mz
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
Max Fx 23 4 4:1.2 DL + LL + WL535.963 1.775 -0 -0 -0 0.019
Min Fx 37 36 4:1.2 DL + LL + WL-360.022 1.236 0 0 0 1.564
Max Fy 9 8 4:1.2 DL + LL + WL125.707 482.571 -0 -0 -0 0.016
Min Fy 7 3 5:1.5 (DL + LL) 113.305 -134.719 0 0 0 -242.504
Max Fz 75 42 5:1.5 (DL + LL) 425.241 0 21.088 0 -0.000 0
Min Fz 76 43 4:1.2 DL + LL + WL398.935 0 -83.216 0 -0.000 0
Max Mx 1 1 1:DL+LL 177.839 14.059 0 0 0 -21.088
Min Mx 1 1 1:DL+LL 177.839 14.059 0 0 0 -21.088
Max My 75 1 5:1.5 (DL + LL) 416.759 -0 21.088 -0 31.632 -0
Min My 76 2 4:1.2 DL + LL + WL392.150 -0 -83.216 -0 -124.824 -0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 3 of 52
 Job No Sheet No Rev
4
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam End Force Summary Cont...

Axial Shear Torsion Bending
Beam Node L/C Fx Fy Fz Mx My Mz
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
Max Mz 2 4 4:1.2 DL + LL + WL251.500 -58.592 -0 -0 -0 863.414
Min Mz 1 3 5:1.5 (DL + LL) 240.948 21.088 -0 -0 -0 -242.513

Beam Force Detail Summary

Sign convention as diagrams:- positive above line, negative below line except Fx where positive is compression. Distance d is given from
beam end A.
Axial Shear Torsion Bending
Beam L/C d Fx Fy Fz Mx My Mz
(m) (kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
Max Fx 23 4:1.2 DL + LL + WL 1.565 535.963 1.775 -0 -0 -0 0.019
Min Fx 37 4:1.2 DL + LL + WL 0 -360.022 1.236 0 0 0 1.564
Max Fy 9 4:1.2 DL + LL + WL 1.800 125.707 482.571 -0 -0 -0 0.016
Min Fy 7 5:1.5 (DL + LL) 0 113.305 -134.719 0 0 0 -242.504
Max Fz 75 5:1.5 (DL + LL) 0 425.241 0 21.088 0 -0.000 0
Min Fz 76 4:1.2 DL + LL + WL 0 398.935 0 -83.216 0 -0.000 0
Max Mx 1 1:DL+LL 0 177.839 14.059 0 0 0 -21.088
Min Mx 1 1:DL+LL 0 177.839 14.059 0 0 0 -21.088
Max My 75 5:1.5 (DL + LL) 1.500 416.759 -0 21.088 -0 31.632 -0
Min My 76 4:1.2 DL + LL + WL 1.500 392.150 -0 -83.216 -0 -124.824 -0
Max Mz 2 4:1.2 DL + LL + WL 10.000 251.500 -58.592 -0 -0 -0 863.414
Min Mz 1 5:1.5 (DL + LL) 10.000 240.948 21.088 -0 -0 -0 -242.513

Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 UB838X292X176
UB838X292X176 0.437 1.000 0.437 BS-4.3.6 2 224.000 246E+3 7.8E+3 221.414
2 UB838X292X176
UB838X292X176 0.688 1.000 0.688 BS-4.3.6 4 224.000 246E+3 7.8E+3 221.414
3 TUB1501506.0
TUB1501506.0 0.386 1.000 0.386 BS-4.8.2.2 2 34.200 1.17E+3 1.17E+3 1.83E+3
4 TUB1501506.0
TUB1501506.0 0.257 1.000 0.257 BS-4.8.2.2 5 34.200 1.17E+3 1.17E+3 1.83E+3
5 TUB1501506.0
TUB1501506.0 0.349 1.000 0.349 BS-4.8.3.3.3 4 34.200 1.17E+3 1.17E+3 1.83E+3
6 TUB1501506.0
TUB1501506.0 0.261 1.000 0.261 BS-4.7 (C) 5 34.200 1.17E+3 1.17E+3 1.83E+3
7 UB838X292X176
UB838X292X176 0.310 1.000 0.310 BS-4.8.2.2 2 224.000 246E+3 7.8E+3 221.414
8 TUB100604.0
TUB100604.0 0.034 1.000 0.034 BS-4.6 (T) 5 12.000 158.000 70.500 156.000
9 UB838X292X176
UB838X292X176 0.479 1.000 0.479 BS-4.8.3.2 4 224.000 246E+3 7.8E+3 221.414
10 TUB1501506.0
TUB1501506.0 0.340 1.000 0.340 BS-4.8.2.2 2 34.200 1.17E+3 1.17E+3 1.83E+3
11 TUB1501506.0
TUB1501506.0 0.349 1.000 0.349 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
12 TUB1501506.0
TUB1501506.0 0.350 1.000 0.350 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
13 TUB1501506.0
TUB1501506.0 0.340 1.000 0.340 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
14 TUB1501506.0
TUB1501506.0 0.319 1.000 0.319 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
15 TUB1501506.0
TUB1501506.0 0.286 1.000 0.286 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
16 TUB1501506.0
TUB1501506.0 0.257 1.000 0.257 BS-4.8.2.2 5 34.200 1.17E+3 1.17E+3 1.83E+3

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 4 of 52
 Job No Sheet No Rev
5
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Utilization Ratio Cont...

Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
17 TUB1501506.0
TUB1501506.0 0.232 1.000 0.232 BS-4.8.2.2 5 34.200 1.17E+3 1.17E+3 1.83E+3
18 TUB1501506.0
TUB1501506.0 0.201 1.000 0.201 BS-4.8.2.2 5 34.200 1.17E+3 1.17E+3 1.83E+3
19 TUB1501506.0
TUB1501506.0 0.192 1.000 0.192 BS-4.7 (C) 2 34.200 1.17E+3 1.17E+3 1.83E+3
20 TUB1501506.0
TUB1501506.0 0.237 1.000 0.237 BS-4.7 (C) 2 34.200 1.17E+3 1.17E+3 1.83E+3
21 TUB1501506.0
TUB1501506.0 0.330 1.000 0.330 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
22 TUB1501506.0
TUB1501506.0 0.448 1.000 0.448 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
23 TUB1501506.0
TUB1501506.0 0.582 1.000 0.582 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
24 TUB1501506.0
TUB1501506.0 0.335 1.000 0.335 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
25 TUB1501506.0
TUB1501506.0 0.344 1.000 0.344 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
26 TUB1501506.0
TUB1501506.0 0.343 1.000 0.343 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
27 TUB1501506.0
TUB1501506.0 0.331 1.000 0.331 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
28 TUB1501506.0
TUB1501506.0 0.308 1.000 0.308 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
29 TUB1501506.0
TUB1501506.0 0.275 1.000 0.275 BS-4.7 (C) 4 34.200 1.17E+3 1.17E+3 1.83E+3
30 TUB1501506.0
TUB1501506.0 0.261 1.000 0.261 BS-4.7 (C) 5 34.200 1.17E+3 1.17E+3 1.83E+3
31 TUB1501506.0
TUB1501506.0 0.255 1.000 0.255 BS-4.7 (C) 5 34.200 1.17E+3 1.17E+3 1.83E+3
32 TUB1501506.0
TUB1501506.0 0.237 1.000 0.237 BS-4.7 (C) 5 34.200 1.17E+3 1.17E+3 1.83E+3
33 TUB1501506.0
TUB1501506.0 0.205 1.000 0.205 BS-4.7 (C) 5 34.200 1.17E+3 1.17E+3 1.83E+3
34 TUB1501506.0
TUB1501506.0 0.172 1.000 0.172 BS-4.8.2.2 2 34.200 1.17E+3 1.17E+3 1.83E+3
35 TUB1501506.0
TUB1501506.0 0.218 1.000 0.218 BS-4.8.2.2 2 34.200 1.17E+3 1.17E+3 1.83E+3
36 TUB1501506.0
TUB1501506.0 0.298 1.000 0.298 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
37 TUB1501506.0
TUB1501506.0 0.414 1.000 0.414 BS-4.8.2.2 4 34.200 1.17E+3 1.17E+3 1.83E+3
38 TUB100604.0
TUB100604.0 0.389 1.000 0.389 BS-4.8.3.3.1 5 12.000 158.000 70.500 156.000
39 TUB100604.0
TUB100604.0 0.339 1.000 0.339 BS-4.8.3.3.1 5 12.000 158.000 70.500 156.000
40 TUB100604.0
TUB100604.0 0.285 1.000 0.285 BS-4.8.3.3.3 5 12.000 158.000 70.500 156.000
41 TUB100604.0
TUB100604.0 0.232 1.000 0.232 BS-4.8.3.3.3 5 12.000 158.000 70.500 156.000
42 TUB100604.0
TUB100604.0 0.179 1.000 0.179 BS-4.8.3.3.3 5 12.000 158.000 70.500 156.000
43 TUB100604.0
TUB100604.0 0.150 1.000 0.150 BS-4.8.2.2 2 12.000 158.000 70.500 156.000
44 TUB100604.0
TUB100604.0 0.150 1.000 0.150 BS-4.8.2.2 2 12.000 158.000 70.500 156.000
45 TUB100604.0
TUB100604.0 0.274 1.000 0.274 BS-4.8.3.3.3 4 12.000 158.000 70.500 156.000
46 TUB100604.0
TUB100604.0 0.321 1.000 0.321 BS-4.8.3.3.3 4 12.000 158.000 70.500 156.000
47 TUB100604.0
TUB100604.0 0.362 1.000 0.362 BS-4.8.3.3.1 4 12.000 158.000 70.500 156.000
48 TUB100604.0
TUB100604.0 0.405 1.000 0.405 BS-4.8.3.3.1 4 12.000 158.000 70.500 156.000
49 TUB100604.0
TUB100604.0 0.447 1.000 0.447 BS-4.8.3.3.1 4 12.000 158.000 70.500 156.000
50 TUB100604.0
TUB100604.0 0.491 1.000 0.491 BS-4.8.3.3.1 4 12.000 158.000 70.500 156.000
51 TUB100604.0
TUB100604.0 0.532 1.000 0.532 BS-4.8.3.3.1 4 12.000 158.000 70.500 156.000
52 TUB100604.0
TUB100604.0 0.409 1.000 0.409 BS-4.8.2.2 5 12.000 158.000 70.500 156.000
53 TUB100604.0
TUB100604.0 0.347 1.000 0.347 BS-4.8.2.2 5 12.000 158.000 70.500 156.000
54 TUB100604.0
TUB100604.0 0.314 1.000 0.314 BS-4.8.3.3.3 2 12.000 158.000 70.500 156.000
55 TUB100604.0
TUB100604.0 0.315 1.000 0.315 BS-4.8.3.3.3 2 12.000 158.000 70.500 156.000
56 TUB100604.0
TUB100604.0 0.317 1.000 0.317 BS-4.8.3.3.3 2 12.000 158.000 70.500 156.000
57 TUB100604.0
TUB100604.0 0.320 1.000 0.320 BS-4.8.3.3.3 2 12.000 158.000 70.500 156.000
58 TUB100604.0
TUB100604.0 0.319 1.000 0.319 BS-4.8.3.3.3 2 12.000 158.000 70.500 156.000
59 TUB100604.0
TUB100604.0 0.362 1.000 0.362 BS-4.8.3.3.3 4 12.000 158.000 70.500 156.000
60 TUB100604.0
TUB100604.0 0.247 1.000 0.247 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
61 TUB100604.0
TUB100604.0 0.285 1.000 0.285 BS-4.8.2.2 4 12.000 158.000 70.500 156.000

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 5 of 52
 Job No Sheet No Rev
6
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Utilization Ratio Cont...

Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
62 TUB100604.0 TUB100604.0 0.331 1.000 0.331 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
63 TUB100604.0 TUB100604.0 0.373 1.000 0.373 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
64 TUB100604.0 TUB100604.0 0.416 1.000 0.416 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
65 TUB100604.0 TUB100604.0 0.461 1.000 0.461 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
66 TUB100604.0 TUB100604.0 0.496 1.000 0.496 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
67 TUB100604.0 TUB100604.0 0.559 1.000 0.559 BS-4.8.2.2 4 12.000 158.000 70.500 156.000
75 Rect 0.40x0.40
N/A 1.6E+3 213E+3 213E+3 361E+3
76 Rect 0.40x0.40
N/A 1.6E+3 213E+3 213E+3 361E+3

Beam Maximum Moments

Distances to maxima are given from beam end A.
Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
1 1 10.000 1:DL+LL Max +ve 0 0
Max -ve 0 0 10.000 -161.675
2:WL Max +ve 0 0 10.000 548.715
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 10.000 387.039
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 10.000 464.447
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 10.000 -242.513
2 2 10.000 1:DL+LL Max +ve 0 0 10.000 161.675
Max -ve 0 0
2:WL Max +ve 0 0 10.000 557.837
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 10.000 719.512
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 10.000 863.414
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 10.000 242.513
Max -ve 0 0
3 3 1.565 1:DL+LL Max +ve 0 0 1.565 0.811
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 0 1.565 -1.816
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.006
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.207
5:1.5 (DL + LL) Max +ve 0 0 1.565 1.216
Max -ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 6 of 52
 Job No Sheet No Rev
7
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
4 5 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0 -1.003
2:WL Max +ve 0 0 1.565 0.167
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -0.988
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -1.186
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0 -1.504
5 6 1.565 1:DL+LL Max +ve 0 0 0 0.007
Max -ve 0 0 0.782 -0.080
2:WL Max +ve 0 0
Max -ve 0 0 1.565 -1.231
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.565 -1.238
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.565 -1.485
5:1.5 (DL + LL) Max +ve 0 0 0 0.010
Max -ve 0 0 0.782 -0.120
6 7 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.565 -0.934
2:WL Max +ve 0 0 0 0.044
Max -ve 0 0 1.565 -0.387
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.321
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.586
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.565 -1.401
7 3 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 0 0 -161.669
2:WL Max +ve 0 0 0 548.705
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 387.036
Max -ve 0 0 1.800 -0.001
4:1.2 DL + LL + WL
Max +ve 0 0 0 464.443
Max -ve 0 0 1.800 -0.001
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0 -242.504
8 5 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 7 of 52
 Job No Sheet No Rev
8
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
9 4 1.800 1:DL+LL Max +ve 0 0 0 161.669
Max -ve 0 0
2:WL Max +ve 0 0 0 557.827
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 719.496
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 863.395
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 242.504
Max -ve 0 0
10 9 1.565 1:DL+LL Max +ve 0 0 0 0.811
Max -ve 0 0 1.565 -0.382
2:WL Max +ve 0 0
Max -ve 0 0 0 -1.817
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.173 -1.167
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.173 -1.400
5:1.5 (DL + LL) Max +ve 0 0 0 1.217
Max -ve 0 0 1.565 -0.573
11 10 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.652 -0.439
2:WL Max +ve 0 0
Max -ve 0 0 1.565 -0.812
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.223
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.467
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.652 -0.659
12 11 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.173 -0.530
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.812
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.218
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.461
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.173 -0.795

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 8 of 52
 Job No Sheet No Rev
9
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
13 12 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.043 -0.646
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.616
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -1.190
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -1.428
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.043 -0.970
14 13 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.043 -0.743
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.482
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -1.133
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -1.359
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.043 -1.114
15 14 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.652 -0.765
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.306
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.391 -1.031
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.391 -1.237
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.652 -1.147
16 15 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.565 -1.003
2:WL Max +ve 0 0 1.565 0.015
Max -ve 0 0 0 -0.190
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.173 -1.014
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.173 -1.217
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.565 -1.504
17 16 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.913 -0.765
2:WL Max +ve 0 0 1.565 0.297
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 9 of 52
 Job No Sheet No Rev
10
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 0 0 0.522 -0.538
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.522 -0.645
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.913 -1.147
18 17 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.522 -0.743
2:WL Max +ve 0 0 1.565 0.475
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.130 -0.409
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.130 -0.491
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.522 -1.114
19 18 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.522 -0.646
2:WL Max +ve 0 0 1.565 0.615
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 0.100
Max -ve 0 0 0.261 -0.137
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 0.120
Max -ve 0 0 0.261 -0.164
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.522 -0.970
20 19 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.391 -0.530
2:WL Max +ve 0 0 1.565 0.818
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 0.486
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 0.583
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.391 -0.795
21 20 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.913 -0.439
2:WL Max +ve 0 0 0 0.818
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.485
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.582
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.913 -0.659

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 10 of 52
 Job No Sheet No Rev
11
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
22 21 1.565 1:DL+LL Max +ve 0 0 1.565 0.811
Max -ve 0 0 0 -0.382
2:WL Max +ve 0 0 1.565 1.842
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 2.653
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 3.183
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 1.565 1.217
Max -ve 0 0 0 -0.573
23 22 1.565 1:DL+LL Max +ve 0 0 0 0.811
Max -ve 0 0
2:WL Max +ve 0 0 0 1.841
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 2.652
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 3.182
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 1.216
Max -ve 0 0
24 23 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.304 -0.214
2:WL Max +ve 0 0
Max -ve 0 0 0 -1.231
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.522 -1.301
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.522 -1.561
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.304 -0.320
25 24 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.173 -0.401
2:WL Max +ve 0 0
Max -ve 0 0 0.391 -0.862
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.913 -1.224
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.913 -1.469
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.173 -0.601
26 25 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.043 -0.540
2:WL Max +ve 0 0
Max -ve 0 0 0.391 -0.737
3:1.0 DL + LL + WL
Max +ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 11 of 52
 Job No Sheet No Rev
12
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 0 0 0.782 -1.244
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.493
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.043 -0.809
27 26 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.043 -0.659
2:WL Max +ve 0 0
Max -ve 0 0 0.261 -0.584
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -1.201
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -1.442
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.043 -0.988
28 27 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.782 -0.717
2:WL Max +ve 0 0
Max -ve 0 0 0.782 -0.453
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.170
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.782 -1.404
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.782 -1.075
29 28 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.434 -0.935
2:WL Max +ve 0 0 1.565 0.401
Max -ve 0 0 0 -0.381
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.130 -1.030
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.130 -1.236
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.434 -1.402
30 29 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0 -0.934
2:WL Max +ve 0 0 0 0.401
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.522 -0.589
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.522 -0.707
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0 -1.401

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 12 of 52
 Job No Sheet No Rev
13
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
31 30 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.130 -0.935
2:WL Max +ve 0 0 1.565 0.416
Max -ve 0 0 0 -0.388
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -1.322
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -1.586
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.130 -1.402
32 31 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.782 -0.717
2:WL Max +ve 0 0 1.565 0.434
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -0.293
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0.652 -0.351
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.782 -1.075
33 32 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.522 -0.659
2:WL Max +ve 0 0 1.565 0.620
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 0.111
Max -ve 0 0 0 -0.192
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 0.134
Max -ve 0 0 0 -0.231
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.522 -0.988
34 33 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.522 -0.540
2:WL Max +ve 0 0 1.565 0.774
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 0.387
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 0.465
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.522 -0.809
35 34 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.391 -0.401
2:WL Max +ve 0 0 1.565 0.896
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 0.695

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 13 of 52
 Job No Sheet No Rev
14
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 0.834
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.391 -0.601
36 35 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 0.261 -0.214
2:WL Max +ve 0 0 1.565 1.310
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.565 1.304
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.565 1.565
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0.261 -0.320
37 36 1.565 1:DL+LL Max +ve 0 0 1.565 0.007
Max -ve 0 0 0.782 -0.080
2:WL Max +ve 0 0 0 1.310
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 1.303
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 1.564
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 1.565 0.010
Max -ve 0 0 0.782 -0.120
38 9 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
39 10 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 14 of 52
 Job No Sheet No Rev
15
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
40 11 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
41 12 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
42 13 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
43 14 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
44 15 1.800 1:DL+LL Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 15 of 52
 Job No Sheet No Rev
16
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 1.800 0.000 0 0
Max -ve 0 -0.000 0 0
45 16 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
46 17 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
47 18 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
48 19 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 16 of 52
 Job No Sheet No Rev
17
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
49 20 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.001 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
50 21 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.001 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.001 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
51 22 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.001 0 0
Max -ve 1.800 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 1.800 -0.000 0 0
52 6 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.062
53 23 2.323 1:DL+LL Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 17 of 52
 Job No Sheet No Rev
18
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.063
54 24 2.323 1:DL+LL Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.063
55 25 2.323 1:DL+LL Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.063
56 26 2.323 1:DL+LL Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.063
57 27 2.323 1:DL+LL Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.063

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 18 of 52
 Job No Sheet No Rev
19
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
58 28 2.323 1:DL+LL Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 2.323 0.000
Max -ve 0 0 1.161 -0.063
59 29 2.323 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.161 -0.063
60 5 2.323 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.161 -0.063
61 16 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.063
62 17 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.000

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 19 of 52
 Job No Sheet No Rev
20
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.063
63 18 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.063
64 19 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.063
65 20 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.063
66 21 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0 2.323 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.042
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.050
5:1.5 (DL + LL) Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.063

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 20 of 52
 Job No Sheet No Rev
21
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Moments Cont...

Beam Node A Length L/C d Max My d Max Mz
(m) (m) (kN-m) (m) (kN-m)
67 22 2.323 1:DL+LL Max +ve 0 0 0 0.000
Max -ve 0 0 1.161 -0.042
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.041
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.049
5:1.5 (DL + LL) Max +ve 0 0 0 0.001
Max -ve 0 0 1.161 -0.062
75 42 1.500 1:DL+LL Max +ve 1.500 21.088 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0.000 0 0
Max -ve 1.500 -86.639 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.500 -65.551 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 1.500 -78.661 0 0
5:1.5 (DL + LL) Max +ve 1.500 31.632 0 0
Max -ve 0 -0.000 0 0
76 43 1.500 1:DL+LL Max +ve 0 0
Max -ve 1.500 -21.088 0 0
2:WL Max +ve 0 0
Max -ve 1.500 -82.932 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 1.500 -104.020 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 1.500 -124.824 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 1.500 -31.632 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 21 of 52
 Job No Sheet No Rev
22
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces

Distances to maxima are given from beam end A.
Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
1 1 10.000 1:DL+LL Max +ve 0 0 0 14.059
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 0 0 -57.760
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -43.701
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -52.441
5:1.5 (DL + LL) Max +ve 0 0 0 21.088
Max -ve 0 0
2 2 10.000 1:DL+LL Max +ve 0 0
Max -ve 0 0 0 -14.059
2:WL Max +ve 0 0
Max -ve 0 0 0 -55.288
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -69.347
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 0 -83.216
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0 -21.088
3 3 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.565 -0.720
2:WL Max +ve 0 0 0 1.155
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.846
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 1.015
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.565 -1.079
4 5 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.565 -0.423
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.098
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.520
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.624
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.565 -0.634
5 6 1.565 1:DL+LL Max +ve 0 0 0 0.214
Max -ve 0 0 1.565 -0.197
2:WL Max +ve 0 0 0 0.945
Max -ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 22 of 52
 Job No Sheet No Rev
23
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0 0 1.159
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 1.391
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 0.321
Max -ve 0 0 1.565 -0.295
6 7 1.565 1:DL+LL Max +ve 0 0 0 0.572
Max -ve 0 0
2:WL Max +ve 0 0 0 0.275
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.847
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 1.016
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 0.858
Max -ve 0 0
7 3 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 0 0 -89.812
2:WL Max +ve 0 0 1.800 308.433
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.800 218.620
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.800 262.344
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 0 -134.719
8 5 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
9 4 1.800 1:DL+LL Max +ve 0 0 0 89.812
Max -ve 0 0
2:WL Max +ve 0 0 1.800 312.330
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 1.800 402.143
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 1.800 482.571
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 134.719

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 23 of 52
 Job No Sheet No Rev
24
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 0
10 9 1.565 1:DL+LL Max +ve 0 0 0 0.968
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.677
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.291
Max -ve 0 0 1.565 -0.119
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.349
Max -ve 0 0 1.565 -0.143
5:1.5 (DL + LL) Max +ve 0 0 0 1.452
Max -ve 0 0
11 10 1.565 1:DL+LL Max +ve 0 0 0 0.174
Max -ve 0 0 1.565 -0.236
2:WL Max +ve 0 0 0 0.034
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.208
Max -ve 0 0 1.565 -0.202
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.250
Max -ve 0 0 1.565 -0.243
5:1.5 (DL + LL) Max +ve 0 0 0 0.261
Max -ve 0 0 1.565 -0.354
12 11 1.565 1:DL+LL Max +ve 0 0 0 0.322
Max -ve 0 0 1.565 -0.088
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.126
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.196
Max -ve 0 0 1.565 -0.214
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.235
Max -ve 0 0 1.565 -0.257
5:1.5 (DL + LL) Max +ve 0 0 0 0.483
Max -ve 0 0 1.565 -0.132
13 12 1.565 1:DL+LL Max +ve 0 0 0 0.263
Max -ve 0 0 1.565 -0.148
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.086
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.177
Max -ve 0 0 1.565 -0.233
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.213
Max -ve 0 0 1.565 -0.280
5:1.5 (DL + LL) Max +ve 0 0 0 0.394
Max -ve 0 0 1.565 -0.221
14 13 1.565 1:DL+LL Max +ve 0 0 0 0.269
Max -ve 0 0 1.565 -0.142
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.113

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 24 of 52
 Job No Sheet No Rev
25
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.156
Max -ve 0 0 1.565 -0.254
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.187
Max -ve 0 0 1.565 -0.305
5:1.5 (DL + LL) Max +ve 0 0 0 0.403
Max -ve 0 0 1.565 -0.213
15 14 1.565 1:DL+LL Max +ve 0 0 0 0.179
Max -ve 0 0 1.565 -0.232
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.075
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.104
Max -ve 0 0 1.565 -0.306
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.125
Max -ve 0 0 1.565 -0.368
5:1.5 (DL + LL) Max +ve 0 0 0 0.268
Max -ve 0 0 1.565 -0.348
16 15 1.565 1:DL+LL Max +ve 0 0 0 0.423
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.131
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.292
Max -ve 0 0 1.565 -0.119
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.350
Max -ve 0 0 1.565 -0.142
5:1.5 (DL + LL) Max +ve 0 0 0 0.634
Max -ve 0 0
17 16 1.565 1:DL+LL Max +ve 0 0 0 0.232
Max -ve 0 0 1.565 -0.179
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.083
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.149
Max -ve 0 0 1.565 -0.262
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.178
Max -ve 0 0 1.565 -0.314
5:1.5 (DL + LL) Max +ve 0 0 0 0.348
Max -ve 0 0 1.565 -0.268
18 17 1.565 1:DL+LL Max +ve 0 0 0 0.142
Max -ve 0 0 1.565 -0.269
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.114
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.027
Max -ve 0 0 1.565 -0.383
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.033
Max -ve 0 0 1.565 -0.460
5:1.5 (DL + LL) Max +ve 0 0 0 0.213

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 25 of 52
 Job No Sheet No Rev
26
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 0 1.565 -0.403
19 18 1.565 1:DL+LL Max +ve 0 0 0 0.148
Max -ve 0 0 1.565 -0.263
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.089
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.058
Max -ve 0 0 1.565 -0.352
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.070
Max -ve 0 0 1.565 -0.423
5:1.5 (DL + LL) Max +ve 0 0 0 0.221
Max -ve 0 0 1.565 -0.394
20 19 1.565 1:DL+LL Max +ve 0 0 0 0.088
Max -ve 0 0 1.565 -0.322
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.130
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.453
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.543
5:1.5 (DL + LL) Max +ve 0 0 0 0.132
Max -ve 0 0 1.565 -0.483
21 20 1.565 1:DL+LL Max +ve 0 0 0 0.236
Max -ve 0 0 1.565 -0.174
2:WL Max +ve 0 0 0 0.030
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.266
Max -ve 0 0 1.565 -0.144
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.319
Max -ve 0 0 1.565 -0.173
5:1.5 (DL + LL) Max +ve 0 0 0 0.354
Max -ve 0 0 1.565 -0.261
22 21 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.565 -0.968
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.685
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.653
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.983
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.565 -1.452
23 22 1.565 1:DL+LL Max +ve 0 0 0 0.719
Max -ve 0 0
2:WL Max +ve 0 0 0 1.170
Max -ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 26 of 52
 Job No Sheet No Rev
27
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0 0 1.890
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 2.268
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 1.079
Max -ve 0 0
24 23 1.565 1:DL+LL Max +ve 0 0 0 0.330
Max -ve 0 0 1.565 -0.080
2:WL Max +ve 0 0
Max -ve 0 0 1.565 -0.410
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.245
Max -ve 0 0 1.565 -0.491
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.294
Max -ve 0 0 1.565 -0.589
5:1.5 (DL + LL) Max +ve 0 0 0 0.495
Max -ve 0 0 1.565 -0.120
25 24 1.565 1:DL+LL Max +ve 0 0 0 0.324
Max -ve 0 0 1.565 -0.086
2:WL Max +ve 0 0 0 0.087
Max -ve 0 0 1.565 -0.238
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.411
Max -ve 0 0 1.565 -0.324
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.493
Max -ve 0 0 1.565 -0.389
5:1.5 (DL + LL) Max +ve 0 0 0 0.486
Max -ve 0 0 1.565 -0.129
26 25 1.565 1:DL+LL Max +ve 0 0 0 0.283
Max -ve 0 0 1.565 -0.127
2:WL Max +ve 0 0 0 0.068
Max -ve 0 0 1.565 -0.257
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.352
Max -ve 0 0 1.565 -0.384
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.422
Max -ve 0 0 1.565 -0.461
5:1.5 (DL + LL) Max +ve 0 0 0 0.425
Max -ve 0 0 1.565 -0.191
27 26 1.565 1:DL+LL Max +ve 0 0 0 0.281
Max -ve 0 0 1.565 -0.130
2:WL Max +ve 0 0 0 0.048
Max -ve 0 0 1.565 -0.277
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.328
Max -ve 0 0 1.565 -0.407
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.394
Max -ve 0 0 1.565 -0.489
5:1.5 (DL + LL) Max +ve 0 0 0 0.421

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 27 of 52
 Job No Sheet No Rev
28
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 0 1.565 -0.195
28 27 1.565 1:DL+LL Max +ve 0 0 0 0.218
Max -ve 0 0 1.565 -0.192
2:WL Max +ve 0 0 0 0.151
Max -ve 0 0 1.565 -0.175
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.369
Max -ve 0 0 1.565 -0.367
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.442
Max -ve 0 0 1.565 -0.440
5:1.5 (DL + LL) Max +ve 0 0 0 0.327
Max -ve 0 0 1.565 -0.289
29 28 1.565 1:DL+LL Max +ve 0 0 0 0.389
Max -ve 0 0 1.565 -0.021
2:WL Max +ve 0 0
Max -ve 0 0 1.565 -0.662
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.052
Max -ve 0 0 1.565 -0.684
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.062
Max -ve 0 0 1.565 -0.820
5:1.5 (DL + LL) Max +ve 0 0 0 0.584
Max -ve 0 0 1.565 -0.032
30 29 1.565 1:DL+LL Max +ve 0 0
Max -ve 0 0 1.565 -0.572
2:WL Max +ve 0 0 0 0.391
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.230
Max -ve 0 0 1.565 -0.506
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.276
Max -ve 0 0 1.565 -0.607
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 0 1.565 -0.858
31 30 1.565 1:DL+LL Max +ve 0 0 0 0.021
Max -ve 0 0 1.565 -0.389
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.513
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.903
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -1.083
5:1.5 (DL + LL) Max +ve 0 0 0 0.032
Max -ve 0 0 1.565 -0.584
32 31 1.565 1:DL+LL Max +ve 0 0 0 0.192
Max -ve 0 0 1.565 -0.218
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.012

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 28 of 52
 Job No Sheet No Rev
29
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.180
Max -ve 0 0 1.565 -0.230
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.216
Max -ve 0 0 1.565 -0.276
5:1.5 (DL + LL) Max +ve 0 0 0 0.289
Max -ve 0 0 1.565 -0.327
33 32 1.565 1:DL+LL Max +ve 0 0 0 0.130
Max -ve 0 0 1.565 -0.281
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.119
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.011
Max -ve 0 0 1.565 -0.399
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.013
Max -ve 0 0 1.565 -0.479
5:1.5 (DL + LL) Max +ve 0 0 0 0.195
Max -ve 0 0 1.565 -0.421
34 33 1.565 1:DL+LL Max +ve 0 0 0 0.127
Max -ve 0 0 1.565 -0.283
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.099
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.028
Max -ve 0 0 1.565 -0.382
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.034
Max -ve 0 0 1.565 -0.459
5:1.5 (DL + LL) Max +ve 0 0 0 0.191
Max -ve 0 0 1.565 -0.425
35 34 1.565 1:DL+LL Max +ve 0 0 0 0.086
Max -ve 0 0 1.565 -0.324
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.078
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.008
Max -ve 0 0 1.565 -0.402
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.010
Max -ve 0 0 1.565 -0.482
5:1.5 (DL + LL) Max +ve 0 0 0 0.130
Max -ve 0 0 1.565 -0.486
36 35 1.565 1:DL+LL Max +ve 0 0 0 0.080
Max -ve 0 0 1.565 -0.330
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.265
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.595
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 0 1.565 -0.714
5:1.5 (DL + LL) Max +ve 0 0 0 0.121

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 29 of 52
 Job No Sheet No Rev
30
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 0 1.565 -0.495
37 36 1.565 1:DL+LL Max +ve 0 0 0 0.197
Max -ve 0 0 1.565 -0.214
2:WL Max +ve 0 0 0 0.833
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 1.030
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0 0 1.236
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0 0 0.295
Max -ve 0 0 1.565 -0.321
38 9 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
39 10 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 0 0
4:1.2 DL + LL + WL
Max +ve 0 0.000 0 0
Max -ve 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
40 11 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
41 12 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 30 of 52
 Job No Sheet No Rev
31
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
42 13 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
43 14 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
44 15 1.800 1:DL+LL Max +ve 0 0.000 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0.000 0 0
Max -ve 0 0
45 16 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 31 of 52
 Job No Sheet No Rev
32
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 -0.000 0 0
46 17 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
47 18 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
48 19 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
49 20 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.001 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
50 21 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 32 of 52
 Job No Sheet No Rev
33
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.001 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
51 22 1.800 1:DL+LL Max +ve 0 0
Max -ve 0 -0.000 0 0
2:WL Max +ve 0 0
Max -ve 0 -0.000 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.000 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -0.001 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -0.000 0 0
52 6 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0
Max -ve 0 0 0 -0.000
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.086
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
53 23 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.086
Max -ve 0 0 2.323 -0.087
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
54 24 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.086
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 33 of 52
 Job No Sheet No Rev
34
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 0 2.323 -0.108
55 25 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.086
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
56 26 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.086
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
57 27 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
58 28 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
59 29 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 34 of 52
 Job No Sheet No Rev
35
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
60 5 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
61 16 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
62 17 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
63 18 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 35 of 52
 Job No Sheet No Rev
36
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
Max -ve 0 0 2.323 -0.108
64 19 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
65 20 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
66 21 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.073
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
67 22 2.323 1:DL+LL Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
2:WL Max +ve 0 0 0 0.000
Max -ve 0 0
3:1.0 DL + LL + WL
Max +ve 0 0 0 0.072
Max -ve 0 0 2.323 -0.072
4:1.2 DL + LL + WL
Max +ve 0 0 0 0.087
Max -ve 0 0 2.323 -0.086
5:1.5 (DL + LL) Max +ve 0 0 0 0.108
Max -ve 0 0 2.323 -0.108
75 42 1.500 1:DL+LL Max +ve 0 14.059 0 0
Max -ve 0 0
2:WL Max +ve 0 0
Max -ve 0 -57.760 0 0

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 36 of 52
 Job No Sheet No Rev
37
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Shear Forces Cont...

Beam Node A Length L/C d Max Fz d Max Fy
(m) (m) (kN) (m) (kN)
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -43.701 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -52.441 0 0
5:1.5 (DL + LL) Max +ve 0 21.088 0 0
Max -ve 0 0
76 43 1.500 1:DL+LL Max +ve 0 0
Max -ve 0 -14.059 0 0
2:WL Max +ve 0 0
Max -ve 0 -55.288 0 0
3:1.0 DL + LL + WL
Max +ve 0 0
Max -ve 0 -69.347 0 0
4:1.2 DL + LL + WL
Max +ve 0 0
Max -ve 0 -83.216 0 0
5:1.5 (DL + LL) Max +ve 0 0
Max -ve 0 -21.088 0 0

Beam Maximum Axial Forces

Distances to maxima are given from beam end A.
Beam Node A Length L/C d Max Fx
(m) (m) (kN)
1 1 10.000 1:DL+LL Max +ve 0 177.839
Max -ve
2:WL Max +ve
Max -ve 0 -48.952
3:1.0 DL + LL + WL
Max +ve 0 128.887
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 154.665
Max -ve
5:1.5 (DL + LL) Max +ve 0 266.759
Max -ve
2 2 10.000 1:DL+LL Max +ve 0 177.839
Max -ve
2:WL Max +ve 0 48.952
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 226.791
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 272.149
Max -ve
5:1.5 (DL + LL) Max +ve 0 266.759
Max -ve
3 3 1.565 1:DL+LL Max +ve 0 103.996
Max -ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 37 of 52
 Job No Sheet No Rev
38
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve
Max -ve 0 -328.976
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -225.002
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -270.003
5:1.5 (DL + LL) Max +ve 0 155.993
Max -ve
4 5 1.565 1:DL+LL Max +ve
Max -ve 0 -142.607
2:WL Max +ve 0 54.447
Max -ve
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -88.160
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -105.792
5:1.5 (DL + LL) Max +ve
Max -ve 0 -213.910
5 6 1.565 1:DL+LL Max +ve
Max -ve 1.565 -30.150
2:WL Max +ve 1.565 271.696
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 241.546
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 289.855
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -45.225
6 7 1.565 1:DL+LL Max +ve 1.565 160.170
Max -ve
2:WL Max +ve 0 16.845
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 177.015
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 212.418
Max -ve
5:1.5 (DL + LL) Max +ve 1.565 240.255
Max -ve
7 3 1.800 1:DL+LL Max +ve 0 75.537
Max -ve
2:WL Max +ve
Max -ve 0 -33.011
3:1.0 DL + LL + WL
Max +ve 0 42.526
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 51.031

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 38 of 52
 Job No Sheet No Rev
39
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve
5:1.5 (DL + LL) Max +ve 0 113.305
Max -ve
8 5 1.800 1:DL+LL Max +ve
Max -ve 1.800 -7.501
2:WL Max +ve
Max -ve 0 -1.542
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.800 -9.044
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.800 -10.852
5:1.5 (DL + LL) Max +ve
Max -ve 1.800 -11.252
9 4 1.800 1:DL+LL Max +ve 0 75.537
Max -ve
2:WL Max +ve 0 32.317
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 107.853
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 129.424
Max -ve
5:1.5 (DL + LL) Max +ve 0 113.305
Max -ve
10 9 1.565 1:DL+LL Max +ve 0 44.268
Max -ve
2:WL Max +ve
Max -ve 0 -285.619
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -241.372
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -289.647
5:1.5 (DL + LL) Max +ve 0 66.402
Max -ve
11 10 1.565 1:DL+LL Max +ve
Max -ve 1.565 -6.382
2:WL Max +ve
Max -ve 0 -244.307
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -250.689
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -300.826
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -9.572
12 11 1.565 1:DL+LL Max +ve
Max -ve 1.565 -49.656

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 39 of 52
 Job No Sheet No Rev
40
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve
Max -ve 0 -202.005
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -251.661
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -301.994
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -74.484
13 12 1.565 1:DL+LL Max +ve
Max -ve 1.565 -84.849
2:WL Max +ve
Max -ve 0 -159.565
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -244.414
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -293.297
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -127.273
14 13 1.565 1:DL+LL Max +ve
Max -ve 1.565 -112.100
2:WL Max +ve
Max -ve 0 -116.835
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -228.934
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -274.721
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -168.149
15 14 1.565 1:DL+LL Max +ve
Max -ve 1.565 -131.393
2:WL Max +ve
Max -ve 0 -73.739
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -205.132
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.565 -246.158
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -197.089
16 15 1.565 1:DL+LL Max +ve
Max -ve 1.565 -142.607
2:WL Max +ve
Max -ve 0 -30.765
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.565 -173.371
4:1.2 DL + LL + WL
Max +ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 40 of 52
 Job No Sheet No Rev
41
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve 1.565 -208.046
5:1.5 (DL + LL) Max +ve
Max -ve 1.565 -213.910
17 16 1.565 1:DL+LL Max +ve
Max -ve 0 -131.393
2:WL Max +ve 0 95.126
Max -ve
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -36.267
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -43.520
5:1.5 (DL + LL) Max +ve
Max -ve 0 -197.089
18 17 1.565 1:DL+LL Max +ve
Max -ve 0 -112.100
2:WL Max +ve 0 136.223
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 24.145
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 28.974
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -168.149
19 18 1.565 1:DL+LL Max +ve
Max -ve 0 -84.849
2:WL Max +ve 0 177.233
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 92.406
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 110.887
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -127.273
20 19 1.565 1:DL+LL Max +ve
Max -ve 0 -49.656
2:WL Max +ve 0 218.234
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 168.600
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 202.319
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -74.484
21 20 1.565 1:DL+LL Max +ve
Max -ve 0 -6.382

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 41 of 52
 Job No Sheet No Rev
42
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve 0 259.383
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 253.023
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 303.628
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -9.572
22 21 1.565 1:DL+LL Max +ve 1.565 44.268
Max -ve
2:WL Max +ve 0 299.809
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 344.076
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 412.892
Max -ve
5:1.5 (DL + LL) Max +ve 1.565 66.402
Max -ve
23 22 1.565 1:DL+LL Max +ve 1.565 103.996
Max -ve
2:WL Max +ve 0 342.640
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 446.636
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 535.963
Max -ve
5:1.5 (DL + LL) Max +ve 1.565 155.993
Max -ve
24 23 1.565 1:DL+LL Max +ve 0 20.464
Max -ve
2:WL Max +ve 1.565 236.636
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 257.078
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 308.494
Max -ve
5:1.5 (DL + LL) Max +ve 0 30.696
Max -ve
25 24 1.565 1:DL+LL Max +ve 0 63.746
Max -ve
2:WL Max +ve 1.565 200.600
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 264.324
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 317.189

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 42 of 52
 Job No Sheet No Rev
43
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve
5:1.5 (DL + LL) Max +ve 0 95.619
Max -ve
26 25 1.565 1:DL+LL Max +ve 0 98.933
Max -ve
2:WL Max +ve 1.565 164.428
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 263.340
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 316.008
Max -ve
5:1.5 (DL + LL) Max +ve 0 148.400
Max -ve
27 26 1.565 1:DL+LL Max +ve 0 126.184
Max -ve
2:WL Max +ve 1.565 127.963
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 254.126
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 304.951
Max -ve
5:1.5 (DL + LL) Max +ve 0 189.276
Max -ve
28 27 1.565 1:DL+LL Max +ve 0 145.470
Max -ve
2:WL Max +ve 1.565 91.141
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 236.590
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 283.908
Max -ve
5:1.5 (DL + LL) Max +ve 0 218.205
Max -ve
29 28 1.565 1:DL+LL Max +ve 0 156.705
Max -ve
2:WL Max +ve 1.565 54.405
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 211.089
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 253.306
Max -ve
5:1.5 (DL + LL) Max +ve 0 235.057
Max -ve
30 29 1.565 1:DL+LL Max +ve 0 160.170
Max -ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 43 of 52
 Job No Sheet No Rev
44
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve 1.565 16.863
Max -ve
3:1.0 DL + LL + WL
Max +ve 1.565 177.012
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 212.414
Max -ve
5:1.5 (DL + LL) Max +ve 0 240.255
Max -ve
31 30 1.565 1:DL+LL Max +ve 1.565 156.705
Max -ve
2:WL Max +ve
Max -ve 0 -24.466
3:1.0 DL + LL + WL
Max +ve 1.565 132.238
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 158.686
Max -ve
5:1.5 (DL + LL) Max +ve 1.565 235.057
Max -ve
32 31 1.565 1:DL+LL Max +ve 1.565 145.470
Max -ve
2:WL Max +ve
Max -ve 0 -65.173
3:1.0 DL + LL + WL
Max +ve 1.565 80.297
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 96.356
Max -ve
5:1.5 (DL + LL) Max +ve 1.565 218.205
Max -ve
33 32 1.565 1:DL+LL Max +ve 1.565 126.184
Max -ve
2:WL Max +ve
Max -ve 0 -106.263
3:1.0 DL + LL + WL
Max +ve 1.565 19.921
Max -ve
4:1.2 DL + LL + WL
Max +ve 1.565 23.906
Max -ve
5:1.5 (DL + LL) Max +ve 1.565 189.276
Max -ve
34 33 1.565 1:DL+LL Max +ve 1.565 98.933
Max -ve
2:WL Max +ve
Max -ve 0 -147.275
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -48.363
4:1.2 DL + LL + WL
Max +ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 44 of 52
 Job No Sheet No Rev
45
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve 0 -58.036
5:1.5 (DL + LL) Max +ve 1.565 148.400
Max -ve
35 34 1.565 1:DL+LL Max +ve 1.565 63.746
Max -ve
2:WL Max +ve
Max -ve 0 -188.275
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -124.550
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -149.460
5:1.5 (DL + LL) Max +ve 1.565 95.619
Max -ve
36 35 1.565 1:DL+LL Max +ve 1.565 20.464
Max -ve
2:WL Max +ve
Max -ve 0 -229.424
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -208.981
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -250.777
5:1.5 (DL + LL) Max +ve 1.565 30.696
Max -ve
37 36 1.565 1:DL+LL Max +ve
Max -ve 0 -30.150
2:WL Max +ve
Max -ve 0 -269.868
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -300.018
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -360.022
5:1.5 (DL + LL) Max +ve
Max -ve 0 -45.225
38 9 1.800 1:DL+LL Max +ve 0 66.995
Max -ve
2:WL Max +ve
Max -ve 0 -48.173
3:1.0 DL + LL + WL
Max +ve 0 18.822
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 22.586
Max -ve
5:1.5 (DL + LL) Max +ve 0 100.493
Max -ve
39 10 1.800 1:DL+LL Max +ve 0 58.470
Max -ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 45 of 52
 Job No Sheet No Rev
46
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve
Max -ve 0 -48.193
3:1.0 DL + LL + WL
Max +ve 0 10.277
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 12.333
Max -ve
5:1.5 (DL + LL) Max +ve 0 87.705
Max -ve
40 11 1.800 1:DL+LL Max +ve 0 49.130
Max -ve
2:WL Max +ve
Max -ve 0 -48.503
3:1.0 DL + LL + WL
Max +ve 0 0.628
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 0.753
Max -ve
5:1.5 (DL + LL) Max +ve 0 73.695
Max -ve
41 12 1.800 1:DL+LL Max +ve 0 40.024
Max -ve
2:WL Max +ve
Max -ve 0 -48.862
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.800 -9.004
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.800 -10.805
5:1.5 (DL + LL) Max +ve 0 60.036
Max -ve
42 13 1.800 1:DL+LL Max +ve 0 30.820
Max -ve
2:WL Max +ve
Max -ve 0 -49.140
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.800 -18.486
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.800 -22.183
5:1.5 (DL + LL) Max +ve 0 46.230
Max -ve
43 14 1.800 1:DL+LL Max +ve 0 21.761
Max -ve
2:WL Max +ve
Max -ve 0 -49.612
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.800 -28.017
4:1.2 DL + LL + WL
Max +ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 46 of 52
 Job No Sheet No Rev
47
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve 1.800 -33.620
5:1.5 (DL + LL) Max +ve 0 32.641
Max -ve
44 15 1.800 1:DL+LL Max +ve 0 12.162
Max -ve
2:WL Max +ve
Max -ve 0 -49.385
3:1.0 DL + LL + WL
Max +ve
Max -ve 1.800 -37.389
4:1.2 DL + LL + WL
Max +ve
Max -ve 1.800 -44.867
5:1.5 (DL + LL) Max +ve 0 18.243
Max -ve
45 16 1.800 1:DL+LL Max +ve 0 12.162
Max -ve
2:WL Max +ve 0 46.782
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 58.944
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 70.733
Max -ve
5:1.5 (DL + LL) Max +ve 0 18.243
Max -ve
46 17 1.800 1:DL+LL Max +ve 0 21.761
Max -ve
2:WL Max +ve 0 47.306
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 69.067
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 82.881
Max -ve
5:1.5 (DL + LL) Max +ve 0 32.641
Max -ve
47 18 1.800 1:DL+LL Max +ve 0 30.820
Max -ve
2:WL Max +ve 0 47.164
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 77.984
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 93.581
Max -ve
5:1.5 (DL + LL) Max +ve 0 46.230
Max -ve
48 19 1.800 1:DL+LL Max +ve 0 40.024
Max -ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 47 of 52
 Job No Sheet No Rev
48
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve 0 47.207
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 87.231
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 104.678
Max -ve
5:1.5 (DL + LL) Max +ve 0 60.036
Max -ve
49 20 1.800 1:DL+LL Max +ve 0 49.130
Max -ve
2:WL Max +ve 0 47.175
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 96.305
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 115.566
Max -ve
5:1.5 (DL + LL) Max +ve 0 73.695
Max -ve
50 21 1.800 1:DL+LL Max +ve 0 58.470
Max -ve
2:WL Max +ve 0 47.177
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 105.647
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 126.776
Max -ve
5:1.5 (DL + LL) Max +ve 0 87.705
Max -ve
51 22 1.800 1:DL+LL Max +ve 0 66.995
Max -ve
2:WL Max +ve 0 47.547
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 114.542
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 137.450
Max -ve
5:1.5 (DL + LL) Max +ve 0 100.493
Max -ve
52 6 2.323 1:DL+LL Max +ve
Max -ve 0 -88.847
2:WL Max +ve 0 64.508
Max -ve
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -24.340
4:1.2 DL + LL + WL
Max +ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 48 of 52
 Job No Sheet No Rev
49
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve 0 -29.208
5:1.5 (DL + LL) Max +ve
Max -ve 0 -133.271
53 23 2.323 1:DL+LL Max +ve
Max -ve 0 -75.179
2:WL Max +ve 0 61.275
Max -ve
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -13.903
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -16.684
5:1.5 (DL + LL) Max +ve
Max -ve 0 -112.768
54 24 2.323 1:DL+LL Max +ve
Max -ve 0 -64.337
2:WL Max +ve 0 62.815
Max -ve
3:1.0 DL + LL + WL
Max +ve
Max -ve 0 -1.521
4:1.2 DL + LL + WL
Max +ve
Max -ve 0 -1.826
5:1.5 (DL + LL) Max +ve
Max -ve 0 -96.505
55 25 2.323 1:DL+LL Max +ve
Max -ve 0 -52.320
2:WL Max +ve 0 63.002
Max -ve
3:1.0 DL + LL + WL
Max +ve 2.323 10.840
Max -ve
4:1.2 DL + LL + WL
Max +ve 2.323 13.008
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -78.480
56 26 2.323 1:DL+LL Max +ve
Max -ve 0 -40.536
2:WL Max +ve 0 63.437
Max -ve
3:1.0 DL + LL + WL
Max +ve 2.323 23.060
Max -ve
4:1.2 DL + LL + WL
Max +ve 2.323 27.672
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -60.804
57 27 2.323 1:DL+LL Max +ve
Max -ve 0 -28.714

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 49 of 52
 Job No Sheet No Rev
50
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve 0 63.975
Max -ve
3:1.0 DL + LL + WL
Max +ve 2.323 35.420
Max -ve
4:1.2 DL + LL + WL
Max +ve 2.323 42.503
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -43.072
58 28 2.323 1:DL+LL Max +ve
Max -ve 0 -16.746
2:WL Max +ve 0 63.805
Max -ve
3:1.0 DL + LL + WL
Max +ve 2.323 47.218
Max -ve
4:1.2 DL + LL + WL
Max +ve 2.323 56.661
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -25.118
59 29 2.323 1:DL+LL Max +ve
Max -ve 0 -5.265
2:WL Max +ve 0 65.094
Max -ve
3:1.0 DL + LL + WL
Max +ve 2.323 59.987
Max -ve
4:1.2 DL + LL + WL
Max +ve 2.323 71.984
Max -ve
5:1.5 (DL + LL) Max +ve
Max -ve 0 -7.898
60 5 2.323 1:DL+LL Max +ve
Max -ve 2.323 -5.265
2:WL Max +ve
Max -ve 0 -61.391
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -66.656
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -79.988
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -7.898
61 16 2.323 1:DL+LL Max +ve
Max -ve 2.323 -16.746
2:WL Max +ve
Max -ve 0 -60.395
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -77.140
4:1.2 DL + LL + WL
Max +ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 50 of 52
 Job No Sheet No Rev
51
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
Max -ve 2.323 -92.568
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -25.118
62 17 2.323 1:DL+LL Max +ve
Max -ve 2.323 -28.714
2:WL Max +ve
Max -ve 0 -61.009
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -89.723
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -107.668
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -43.072
63 18 2.323 1:DL+LL Max +ve
Max -ve 2.323 -40.536
2:WL Max +ve
Max -ve 0 -60.883
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -101.419
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -121.703
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -60.804
64 19 2.323 1:DL+LL Max +ve
Max -ve 2.323 -52.320
2:WL Max +ve
Max -ve 0 -60.865
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -113.185
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -135.822
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -78.480
65 20 2.323 1:DL+LL Max +ve
Max -ve 2.323 -64.337
2:WL Max +ve
Max -ve 0 -61.104
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -125.440
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -150.528
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -96.505
66 21 2.323 1:DL+LL Max +ve
Max -ve 2.323 -75.179

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 51 of 52
 Job No Sheet No Rev
52
Software licensed to Meinhardt EPCM Sdn. Bhd Part
CONNECTED User: Dexter Tan
Job Title Ref

By Date26-Jul-23 Chd

Client File Date/Time 28-Jul-2023 16:02

MainRoof_Distillationskid.STD

Beam Maximum Axial Forces Cont...

Beam Node A Length L/C d Max Fx
(m) (m) (kN)
2:WL Max +ve
Max -ve 0 -59.959
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -135.138
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -162.165
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -112.768
67 22 2.323 1:DL+LL Max +ve
Max -ve 2.323 -88.847
2:WL Max +ve
Max -ve 0 -63.728
3:1.0 DL + LL + WL
Max +ve
Max -ve 2.323 -152.576
4:1.2 DL + LL + WL
Max +ve
Max -ve 2.323 -183.091
5:1.5 (DL + LL) Max +ve
Max -ve 2.323 -133.271
75 42 1.500 1:DL+LL Max +ve 0 283.494
Max -ve
2:WL Max +ve
Max -ve 0 -48.952
3:1.0 DL + LL + WL
Max +ve 0 234.542
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 281.451
Max -ve
5:1.5 (DL + LL) Max +ve 0 425.241
Max -ve
76 43 1.500 1:DL+LL Max +ve 0 283.494
Max -ve
2:WL Max +ve 0 48.952
Max -ve
3:1.0 DL + LL + WL
Max +ve 0 332.446
Max -ve
4:1.2 DL + LL + WL
Max +ve 0 398.935
Max -ve
5:1.5 (DL + LL) Max +ve 0 425.241
Max -ve

Print Time/Date: 17/08/2023 18:26 STAAD.Pro CONNECT Edition 22.12.00.142 Print Run 52 of 52
Distillation Skid - Main Roof Column Anchorbolt check & Pile Check

X1 115 mm bolt number = 18

X2 230 mm
X3 345 mm
X4 480 mm

Xmax 480 mm

Z = 3.462917 m

Moment At Base Plate = 65 kNm (service)

Horz Force at Top of Pilecap = 70 kN (service)
Allowed Z to pilecap base = 1.5 m
Pilecap Base moment = 105 kNm (service)
Shear Force = 70 kN
Factor of safety = 1.5

Max Bolt Pullout = 28.2 kN Per bolt

Max Shear force = 5.8 kN Per bolt

Provide M24 G8.8

Pnom = 158 < 28.2
Pshear = 132 < 5.8

Combine Check = 0.18 + 0.04

= 0.22 < 1.4

Piling Check

Foundation Axial = 350 kN

Base Bending = 105 kNm
Pilecap SW = 140.4 kN

6P Pile cap level Arm = 2.5 m

Max Pile Tension = 21 kN

Max Compression = 103 kN
Min Compression = 39 kN > 21 kN
No Tension Pile
Tension Factor of safety = 1.85
 Title : 0 Job Ref: 0
Date 17-Aug-23
Time : 15:16
Designed By: 0
PILE ECCENTRICITY CHECK, 6P Checked By : 0
Calculation Output

LEFT SIDE CHECKING :

AvxL1 = (1200 / 3) - (0.5 x 450)

= 175 mm

dxL1 = SQRT [(3 x 1.6 x 450 x 1000 x 175 / (2 x 0.50 x 3000)]

= 354.97 mm

Recommend H = 848.53 + 75 + 40 + (0.5 x 32)

980 mm

Pile Cap Depth = 1500 mm

#
Mx-Left = 3 x 1.6 x 450 x 0.175 B = 3000 mm
= 378 kNm

d = 1500 - 75 - 40 - (0.5 x 25)

= 1372.5 mm k = 0.00223

z = 0.998 d > 0.95d, z = 0.95 d Recommend

= 0.95 d 14 T 25
6873 mm2
As = (378 x 10E6) / [0.87 x 460 x 0.95 x 1372.5] Provided
= 725 mm2 14 T 25
6873 mm2
As min = (0.15 / 100) x 3000 x 1500 T 25 - 225
= 6750 mm2 OK

Punching Shear Check

Vp = 6 x 1.6 x 450 Perimeter, P = 2 x (450 + 1200)

= 4320 kN = 3300 mm

vp = 4320 x 1000 / (3300 x 1372.5)

= 0.954 N/mm2 < 0.8 sqrt(fcu) = 4.382 N/mm2 OK

Binder Recommend
8 T 12
905 mm2
As = 0.5 x 0.25 % As(Mx Max) Provided
= 0.5 x 0.25 x 6873 4 T 12 8 T 12
= 860 mm2 Spacing +/- 158 mm 905 mm2
OK
Shear Check, Mx-Left

avxL-1 = 400 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = 0.551 N/mm2

115.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 3000 mm
d = 1372.5 mm

VxL-1 = 1 x 1.6 x 450

= 720 kN

vxL-1 = (720 x 1000) / (3000 x 1372.5)

= 0.175 N/mm2

As = 6873 mm2 14 T 25

vcxL-1 = (0.79/1.25) x (0.551 x 1.063 x 1)

= 0.371 N/mm2

vcxL' -1 = 2 x 1372.5 x 0.371 / 115

= 8.856 > 0.175 OK

avxL-2 = 400 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = 0.551 N/mm2

115.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 3000 mm
d = 1372.5 mm

VxL-2 = 2 x 1.6 x 450

= 1440 kN

vxL-2 = (1440 x 1000) / (3000 x 1372.5)

= 0.35 N/mm2

As = 6873 mm2 14 T 25

vcxL-2 = (0.79/1.25) x (0.551 x 1.063 x 1)

= 0.371 N/mm2

vcxL' -2 = 2 x 1372.5 x 0.371 / 115

= 8.856 > 0.35 OK

avxL-3 = 400 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = 0.551 N/mm2

115.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 3000 mm
d = 1372.5 mm

VxL-3 = 3 x 1.6 x 450

= 2160 kN

vxL-3 = (2160 x 1000) / (3000 x 1372.5)

= 0.525 N/mm2

As = 6873 mm2 14 T 25

vcxL-3 = (0.79/1.25) x (0.551 x 1.063 x 1)

= 0.371 N/mm2

vcxL' -3 = 2 x 1372.5 x 0.371 / 115

= 8.856 > 0.525 OK

avxL-4 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-4 = Not required

= - kN
vxL-4 = Not required
= - N/mm2

As = - mm2 - T -

vcxL-4 = Not required

= - N/mm2

vcxL' -4 = Not required

= - > - -

avxL-5 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-5 = Not required

= - kN

vxL-5 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-5 = Not required

= - N/mm2

vcxL' -5 = Not required

= - > - -

avxL-6 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-6 = Not required

= - kN

vxL-6 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-6 = Not required

= - N/mm2

vcxL' -6 = Not required

= - > - -

avxL-7 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-7 = Not required

= - kN

vxL-7 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-7 = Not required

= - N/mm2

vcxL' -7 = Not required

= - > - -
avxL-8 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2
-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-8 = Not required

= - kN

vxL-8 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-8 = Not required

= - N/mm2

vcxL' -8 = Not required

= - > - -

avxL-9 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-9 = Not required

= - kN

vxL-9 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-9 = Not required

= - N/mm2

vcxL' -9 = Not required

= - > - -

avxL-10 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-10 = Not required

= - kN

vxL-10 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-10 = Not required

= - N/mm2

vcxL' -10 = Not required

= - > - -

avxL-11 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-11 = Not required

= - kN

vxL-11 = Not required

= - N/mm2
As = - mm2 - T -

vcxL-11 = Not required

= - N/mm2

vcxL' -11 = Not required

= - > - -

avxL-12 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-12 = Not required

= - kN

vxL-12 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-12 = Not required

= - N/mm2

vcxL' -12 = Not required

= - > - -

avxL-13 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-13 = Not required

= - kN

vxL-13 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-13 = Not required

= - N/mm2

vcxL' -13 = Not required

= - > - -

avxL-14 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-14 = Not required

= - kN

vxL-14 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-14 = Not required

= - N/mm2

vcxL' -14 = Not required

= - > - -

avxL-15 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-15 = Not required

= - kN

vxL-15 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-15 = Not required

= - N/mm2

vcxL' -15 = Not required

= - > - -

avxL-16 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-16 = Not required

= - kN

vxL-16 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-16 = Not required

= - N/mm2

vcxL' -16 = Not required

= - > - -

avxL-17 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-17 = Not required

= - kN

vxL-17 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-17 = Not required

= - N/mm2

vcxL' -17 = Not required

= - > - -

avxL-18 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-18 = Not required

= - kN

vxL-18 = Not required

= - N/mm2

As = - mm2 - T -
vcxL-18 = Not required
= - N/mm2

vcxL' -18 = Not required

= - > - -

avxL-19 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-19 = Not required

= - kN

vxL-19 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-19 = Not required

= - N/mm2

vcxL' -19 = Not required

= - > - -

avxL-20 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-20 = Not required

= - kN

vxL-20 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-20 = Not required

= - N/mm2

vcxL' -20 = Not required

= - > - -

avxL-21 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-21 = Not required

= - kN

vxL-21 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-21 = Not required

= - N/mm2

vcxL' -21 = Not required

= - > - -

avxL-22 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm
VxL-22 = Not required
= - kN

vxL-22 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-22 = Not required

= - N/mm2

vcxL' -22 = Not required

= - > - -

avxL-23 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-23 = Not required

= - kN

vxL-23 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-23 = Not required

= - N/mm2

vcxL' -23 = Not required

= - > - -

avxL-24 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxL-24 = Not required

= - kN

vxL-24 = Not required

= - N/mm2

As = - mm2 - T -

vcxL-24 = Not required

= - N/mm2

vcxL' -24 = Not required

= - > - -
 Title : 0 Job Ref: 0
Date 17-Aug-23
Time : 15:16
Designed By: 0
PILE ECCENTRICITY CHECK, 6P Checked By : 0
Calculation Output

RIGHT SIDE CHECKING :

AvxR1 = (1200 / 3) - (0.5 x 450)

= 175 mm

dxR1 = SQRT [(3 x 1.6 x 450 x 1000 x 175 / (2 x 0.50 x 3000)]

= 354.97 mm

Recommend H = 848.53 + 75 + 40 + (0.5 x 32)

980 mm

Pile Cap Depth = 1500 mm

Mx-Right = 3 x 1.6 x 450 x 0.175 B = 3000 mm

= 378 kNm

d = 1500 - 75 - 40 - (0.5 x 25) k = 0.00223

= 1372.5 mm

z = 0.998 d > 0.95d, z = 0.95 d

= 0.95 d

As = (378 x 10E6) / [0.87 x 460 x 0.95 x 1372.5] Provided

= 725 mm2 14 T 25
6873 mm2
As min = (0.15 / 100) x 3000 x 1500 T 25 - 225
= 6750 mm2 OK

Punching Shear Check

Vp = 6 x 1.6 x 450 Perimeter, P = 2 x (450 + 1200)

= 4320 kN = 3300 mm

vp = 4320 x 1000 / (3300 x 1372.5)

= 0.954 N/mm2 < 0.8 sqrt(fcu) = 4.382 N/mm2 OK

Binder

As = 0.5 x 0.25 % As(Mx Max) Provided

= 0.5 x 0.25 x 6873 8 T 12
= 860 mm2 905 mm2
OK
Shear Check, Mx-Right

avxR-1 = 400 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = 0.551 N/mm2

115.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 3000 mm
d = 1372.5 mm

VxR-1 = 1 x 1.6 x 450

= 720 kN

vxR-1 = (720 x 1000) / (3000 x 1372.5)

= 0.175 N/mm2

As = 6873 mm2 14 T 25

vcxR-1 = (0.79/1.25) x (0.551 x 1.063 x 1)

= 0.371 N/mm2

vcxR' -1 = 2 x 1372.5 x 0.371 / 115

= 8.856 > 0.175 OK

avxR-2 = 400 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = 0.551 N/mm2

115.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 3000 mm
d = 1372.5 mm

VxR-2 = 2 x 1.6 x 450

= 1440 kN

vxR-2 = (1440 x 1000) / (3000 x 1372.5)

= 0.35 N/mm2

As = 6873 mm2 14 T 25

vcxR-2 = (0.79/1.25) x (0.551 x 1.063 x 1)

= 0.371 N/mm2

vcxR' -2 = 2 x 1372.5 x 0.371 / 115

= 8.856 > 0.35 OK

avxR-3 = 400 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = 0.551 N/mm2

115.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 3000 mm
d = 1372.5 mm

VxR-3 = 3 x 1.6 x 450

= 2160 kN

vxR-3 = (2160 x 1000) / (3000 x 1372.5)

= 0.525 N/mm2

As = 6873 mm2 14 T 25

vcxR-3 = (0.79/1.25) x (0.551 x 1.063 x 1)

= 0.371 N/mm2

vcxR' -3 = 2 x 1372.5 x 0.371 / 115

= 8.856 > 0.525 OK

avxR-4 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-4 = Not required

= - kN
vxR-4 = Not required
= - N/mm2

As = - mm2 - T -

vcxR-4 = Not required

= - N/mm2

vcxR' -4 = Not required

= - > - -

avxR-5 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-5 = Not required

= - kN

vxR-5 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-5 = Not required

= - N/mm2

vcxR' -5 = Not required

= - > - -

avxR-6 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-6 = Not required

= - kN

vxR-6 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-6 = Not required

= - N/mm2

vcxR' -6 = Not required

= - > - -

avxR-7 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-7 = Not required

= - kN

vxR-7 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-7 = Not required

= - N/mm2

vcxR' -7 = Not required

= - > - -
avxR-8 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2
-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-8 = Not required

= - kN

vxR-8 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-8 = Not required

= - N/mm2

vcxR' -8 = Not required

= - > - -

avxR-9 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-9 = Not required

= - kN

vxR-9 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-9 = Not required

= - N/mm2

vcxR' -9 = Not required

= - > - -

avxR-10 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-10 = Not required

= - kN

vxR-10 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-10 = Not required

= - N/mm2

vcxR' -10 = Not required

= - > - -

avxR-11 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-11 = Not required

= - kN

vxR-11 = Not required

= - N/mm2
As = - mm2 - T -

vcxR-11 = Not required

= - N/mm2

vcxR' -11 = Not required

= - > - -

avxR-12 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-12 = Not required

= - kN

vxR-12 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-12 = Not required

= - N/mm2

vcxR' -12 = Not required

= - > - -

avxR-13 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-13 = Not required

= - kN

vxR-13 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-13 = Not required

= - N/mm2

vcxR' -13 = Not required

= - > - -

avxR-14 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-14 = Not required

= - kN

vxR-14 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-14 = Not required

= - N/mm2

vcxR' -14 = Not required

= - > - -

avxR-15 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-15 = Not required

= - kN

vxR-15 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-15 = Not required

= - N/mm2

vcxR' -15 = Not required

= - > - -

avxR-16 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-16 = Not required

= - kN

vxR-16 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-16 = Not required

= - N/mm2

vcxR' -16 = Not required

= - > - -

avxR-17 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-17 = Not required

= - kN

vxR-17 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-17 = Not required

= - N/mm2

vcxR' -17 = Not required

= - > - -

avxR-18 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-18 = Not required

= - kN

vxR-18 = Not required

= - N/mm2

As = - mm2 - T -
vcxR-18 = Not required
= - N/mm2

vcxR' -18 = Not required

= - > - -

avxR-19 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-19 = Not required

= - kN

vxR-19 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-19 = Not required

= - N/mm2

vcxR' -19 = Not required

= - > - -

avxR-20 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-20 = Not required

= - kN

vxR-20 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-20 = Not required

= - N/mm2

vcxR' -20 = Not required

= - > - -

avxR-21 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-21 = Not required

= - kN

vxR-21 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-21 = Not required

= - N/mm2

vcxR' -21 = Not required

= - > - -

avxR-22 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm
VxR-22 = Not required
= - kN

vxR-22 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-22 = Not required

= - N/mm2

vcxR' -22 = Not required

= - > - -

avxR-23 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-23 = Not required

= - kN

vxR-23 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-23 = Not required

= - N/mm2

vcxR' -23 = Not required

= - > - -

avxR-24 = 0 - (0.5 x 450) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-285.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 3000 mm
d = 1372.5 mm

VxR-24 = Not required

= - kN

vxR-24 = Not required

= - N/mm2

As = - mm2 - T -

vcxR-24 = Not required

= - N/mm2

vcxR' -24 = Not required

= - > - -
 Title : 0 Job Ref: 0
Date 17-Aug-23
Time : 15:16
Designed By: 0
PILE ECCENTRICITY CHECK, 6P Checked By : 0
Calculation Output

TOP SIDE CHECKING :

AvxT1 = (2500 / 2) - (0.5 x 1200)

= 650 mm

dxT1 = SQRT [(2 x 1.6 x 450 x 1000 x 650 / (2 x 0.50 x 1300)]

= 848.53 mm

Recommend H = 848.53 + 75 + 40 + (0.5 x 32)

980 mm

Pile Cap Depth = 1500 mm

My-Top = 2 x 1.6 x 450 x 0.65 B = 1300 mm

= 936

d = 1500 - 75 - 40 - 25 - (0.5 x 25) k = 0.013218

= 1347.5 mm

z = 0.986 d > 0.95d, z = 0.95 d Recommend

= 0.95 d 6 T 25
2946 mm2
As = (936 x 10E6) / [0.87 x 460 x 0.95 x 1347.5] Provided
= 1828 mm2 6 T 25
2946 mm2
As min = (0.15 / 100) x 1300 x 1500 T 25 - 244
= 2925 mm2 OK

Punching Shear Check

Vp = 6 x 1.6 x 450 Perimeter, P = 2 x (450 + 1200)

= 4320 kN = 3300 mm

vp = 4320 x 1000 / (3300 x 1372.5)

= 0.954 N/mm2 < 0.8 sqrt(fcu) = 4.382 N/mm2 OK

Binder

As = 0.5 x 0.25 % As(Mx Max) Provided

= 0.5 x 0.25 x 6873 8 T 12
= 860 mm2 905 mm2
OK
Shear Check, My-Top

avyT-1 = 1250 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = 0.552 N/mm2

590.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 1300 mm
d = 1347.5 mm

VyT-1 = 1 x 1.6 x 450

= 720 kN

vyT-1 = (720 x 1000) / (1300 x 1347.5)

= 0.412 N/mm2

As = 2946 mm2 6 T 25

vcyT-1 = (0.79/1.25) x (0.552 x 1.063 x 1)

= 0.371 N/mm2

vcyT' -1 = 2 x 1347.5 x 0.371 / 590

= 1.695 > 0.412 OK

avyT-2 = 1250 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = 0.552 N/mm2

590.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 1300 mm
d = 1347.5 mm

VyT-2 = 2 x 1.6 x 450

= 1440 kN

vyT-2 = (1440 x 1000) / (1300 x 1347.5)

= 0.823 N/mm2

As = 2946 mm2 6 T 25

vcyT-2 = (0.79/1.25) x (0.552 x 1.063 x 1)

= 0.371 N/mm2

vcyT' -2 = 2 x 1347.5 x 0.371 / 590

= 1.695 > 0.823 OK

avyT-3 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-3 = Not required

= - kN

vyT-3 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-3 = Not required

= - N/mm2

vcyT' -3 = Not required

= - > - -

avyT-4 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-4 = Not required

= - kN
vyT-4 = Not required
= - N/mm2

As = - mm2 - T -

vcyT-4 = Not required

= - N/mm2

vcyT' -4 = Not required

= - > - -

avyT-5 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-5 = Not required

= - kN

vyT-5 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-5 = Not required

= - N/mm2

vcyT' -5 = Not required

= - > - -

avyT-6 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-6 = Not required

= - kN

vyT-6 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-6 = Not required

= - N/mm2

vcyT' -6 = Not required

= - > - -

avyT-7 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-7 = Not required

= - kN

vyT-7 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-7 = Not required

= - N/mm2

vcyT' -7 = Not required

= - > - -
avyT-8 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2
-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-8 = Not required

= - kN

vyT-8 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-8 = Not required

= - N/mm2

vcyT' -8 = Not required

= - > - -

avyT-9 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-9 = Not required

= - kN

vyT-9 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-9 = Not required

= - N/mm2

vcyT' -9 = Not required

= - > - -

avyT-10 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-10 = Not required

= - kN

vyT-10 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-10 = Not required

= - N/mm2

vcyT' -10 = Not required

= - > - -

avyT-11 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-11 = Not required

= - kN

vyT-11 = Not required

= - N/mm2
As = - mm2 - T -

vcyT-11 = Not required

= - N/mm2

vcyT' -11 = Not required

= - > - -

avyT-12 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-12 = Not required

= - kN

vyT-12 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-12 = Not required

= - N/mm2

vcyT' -12 = Not required

= - > - -

avyT-13 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-13 = Not required

= - kN

vyT-13 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-13 = Not required

= - N/mm2

vcyT' -13 = Not required

= - > - -

avyT-14 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-14 = Not required

= - kN

vyT-14 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-14 = Not required

= - N/mm2

vcyT' -14 = Not required

= - > - -

avyT-15 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-15 = Not required

= - kN

vyT-15 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-15 = Not required

= - N/mm2

vcyT' -15 = Not required

= - > - -

avyT-16 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-16 = Not required

= - kN

vyT-16 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-16 = Not required

= - N/mm2

vcyT' -16 = Not required

= - > - -

avyT-17 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-17 = Not required

= - kN

vyT-17 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-17 = Not required

= - N/mm2

vcyT' -17 = Not required

= - > - -

avyT-18 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-18 = Not required

= - kN

vyT-18 = Not required

= - N/mm2

As = - mm2 - T -
vcyT-18 = Not required
= - N/mm2

vcyT' -18 = Not required

= - > - -

avyT-19 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-19 = Not required

= - kN

vyT-19 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-19 = Not required

= - N/mm2

vcyT' -19 = Not required

= - > - -

avyT-20 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-20 = Not required

= - kN

vyT-20 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-20 = Not required

= - N/mm2

vcyT' -20 = Not required

= - > - -

avyT-21 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-21 = Not required

= - kN

vyT-21 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-21 = Not required

= - N/mm2

vcyT' -21 = Not required

= - > - -

avyT-22 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm
VyT-22 = Not required
= - kN

vyT-22 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-22 = Not required

= - N/mm2

vcyT' -22 = Not required

= - > - -

avyT-23 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-23 = Not required

= - kN

vyT-23 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-23 = Not required

= - N/mm2

vcyT' -23 = Not required

= - > - -

avyT-24 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyT-24 = Not required

= - kN

vyT-24 = Not required

= - N/mm2

As = - mm2 - T -

vcyT-24 = Not required

= - N/mm2

vcyT' -24 = Not required

= - > - -
 Title : 0 Job Ref: 0
Date 17-Aug-23
Time : 15:16
Designed By: 0
PILE ECCENTRICITY CHECK, 6P Checked By : 0
Calculation Output

BOTTOM SIDE CHECKING :

AvxB1 = (2500 / 2) - (0.5 x 1200)

= 650 mm

dxB1 = SQRT [(2 x 1.6 x 450 x 1000 x 650 / (2 x 0.50 x 1300)]

= 848.53 mm

Recommend H = 848.53 + 75 + 40 + (0.5 x 32)

980 mm

Pile Cap Depth = 1500 mm

My-Bottom = 2 x 1.6 x 450 x 0.65 B = 1300 mm

= 936 kNm

d = 1500 - 75 - 40 - 25 - (0.5 x 25) k = 0.013218

= 1347.5 mm

z = 0.986 d > 0.95d, z = 0.95 d

= 0.95 d

As = (936 x 10E6) / [0.87 x 460 x 0.95 x 1347.5] Provided

= 1828 mm2 6 T 25
2946 mm2
As min = (0.15 / 100) x 1300 x 1500 T 25 - 244
= 2925 mm2 OK

Punching Shear Check

Vp = 6 x 1.6 x 450 Perimeter, P = 2 x (450 + 1200)

= 4320 kN = 3300 mm

vp = 4320 x 1000 / (3300 x 1372.5)

= 0.954 N/mm2 < 0.8 sqrt(fcu) = 4.382 N/mm2 OK

Binder

As = 0.5 x 0.25 % As(Mx Max) Provided

= 0.5 x 0.25 x 6873 8 T 12
= 860 mm2 905 mm2
OK
Shear Check, My-Bottom

avyB-1 = 1250 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = 0.552 N/mm2

590.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 1300 mm
d = 1347.5 mm

VyB-1 = 1 x 1.6 x 450

= 720 kN

vyB-1 = (720 x 1000) / (1300 x 1347.5)

= 0.412 N/mm2

As = 2946 mm2 6 T 25

vcyB-1 = (0.79/1.25) x (0.552 x 1.063 x 1)

= 0.371 N/mm2

vcyB' -1 = 2 x 1347.5 x 0.371 / 590

= 1.695 > 0.412 OK

avyB-2 = 1250 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = 0.552 N/mm2

590.00 mm b = (fcu/25)1/3 = 1.063 N/mm2
c = (400/d)1/4 = 1.00
B = 1300 mm
d = 1347.5 mm

VyB-2 = 2 x 1.6 x 450

= 1440 kN

vyB-2 = (1440 x 1000) / (1300 x 1347.5)

= 0.823 N/mm2

As = 2946 mm2 6 T 25

vcyB-2 = (0.79/1.25) x (0.552 x 1.063 x 1)

= 0.371 N/mm2

vcyB' -2 = 2 x 1347.5 x 0.371 / 590

= 1.695 > 0.823 OK

avyB-3 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-3 = Not required

= - kN

vyB-3 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-3 = Not required

= - N/mm2

vcyB' -3 = Not required

= - > - -

avyB-4 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-4 = Not required

= - kN
vyB-4 = Not required
= - N/mm2

As = - mm2 - T -

vcyB-4 = Not required

= - N/mm2

vcyB' -4 = Not required

= - > - -

avyB-5 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-5 = Not required

= - kN

vyB-5 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-5 = Not required

= - N/mm2

vcyB' -5 = Not required

= - > - -

avyB-6 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-6 = Not required

= - kN

vyB-6 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-6 = Not required

= - N/mm2

vcyB' -6 = Not required

= - > - -

avyB-7 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-7 = Not required

= - kN

vyB-7 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-7 = Not required

= - N/mm2

vcyB' -7 = Not required

= - > - -
avyB-8 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2
-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-8 = Not required

= - kN

vyB-8 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-8 = Not required

= - N/mm2

vcyB' -8 = Not required

= - > - -

avyB-9 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-9 = Not required

= - kN

vyB-9 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-9 = Not required

= - N/mm2

vcyB' -9 = Not required

= - > - -

avyB-10 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-10 = Not required

= - kN

vyB-10 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-10 = Not required

= - N/mm2

vcyB' -10 = Not required

= - > - -

avyB-11 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-11 = Not required

= - kN

vyB-11 = Not required

= - N/mm2
As = - mm2 - T -

vcyB-11 = Not required

= - N/mm2

vcyB' -11 = Not required

= - > - -

avyB-12 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-12 = Not required

= - kN

vyB-12 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-12 = Not required

= - N/mm2

vcyB' -12 = Not required

= - > - -

avyB-13 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-13 = Not required

= - kN

vyB-13 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-13 = Not required

= - N/mm2

vcyB' -13 = Not required

= - > - -

avyB-14 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-14 = Not required

= - kN

vyB-14 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-14 = Not required

= - N/mm2

vcyB' -14 = Not required

= - > - -

avyB-15 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-15 = Not required

= - kN

vyB-15 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-15 = Not required

= - N/mm2

vcyB' -15 = Not required

= - > - -

avyB-16 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-16 = Not required

= - kN

vyB-16 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-16 = Not required

= - N/mm2

vcyB' -16 = Not required

= - > - -

avyB-17 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-17 = Not required

= - kN

vyB-17 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-17 = Not required

= - N/mm2

vcyB' -17 = Not required

= - > - -

avyB-18 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-18 = Not required

= - kN

vyB-18 = Not required

= - N/mm2

As = - mm2 - T -
vcyB-18 = Not required
= - N/mm2

vcyB' -18 = Not required

= - > - -

avyB-19 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-19 = Not required

= - kN

vyB-19 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-19 = Not required

= - N/mm2

vcyB' -19 = Not required

= - > - -

avyB-20 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-20 = Not required

= - kN

vyB-20 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-20 = Not required

= - N/mm2

vcyB' -20 = Not required

= - > - -

avyB-21 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-21 = Not required

= - kN

vyB-21 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-21 = Not required

= - N/mm2

vcyB' -21 = Not required

= - > - -

avyB-22 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm
VyB-22 = Not required
= - kN

vyB-22 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-22 = Not required

= - N/mm2

vcyB' -22 = Not required

= - > - -

avyB-23 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-23 = Not required

= - kN

vyB-23 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-23 = Not required

= - N/mm2

vcyB' -23 = Not required

= - > - -

avyB-24 = 0 - (0.5 x 1200) - (0.3 x 200) a = (100As/bd)1/3 = - N/mm2

-660.00 mm b = (fcu/25)1/3 = - N/mm2
c = (400/d)1/4 = -
B = 1300 mm
d = 1347.5 mm

VyB-24 = Not required

= - kN

vyB-24 = Not required

= - N/mm2

As = - mm2 - T -

vcyB-24 = Not required

= - N/mm2

vcyB' -24 = Not required

= - > - -