TAG DESCRIPTION GRAPHIC TAG DESCRIPTION GRAPHIC TAG DESCRIPTION GRAPHIC TAG DESCRIPTION GRAPHIC

JOB COPY
ALL IDEAS, DESIGN ARRANGEMENTS AND PLANS INDICATED OR REPRESENTED BY THIS DRAWING ARE OWNED BY AND THE PROPERTY OF ARK ARCHITECTS, INC. AND WERE CREATED EVOLVED AND DEVELOPED FOR USE ON AND IN CONNECTION WITH THE SPECIFIED PROJECT. NONE OF SUCH IDEAS ARRANGEMENTS OR PLANS SHALL BE USED BY OR DISCLOSED TO ANY PERSON FIRM OR CORPORATION FOR ANY PURPOSE WHATSOEVER WITHOUT THE WRITTEN PERMISSION OF ARK ARCHITECTS, INC. A R K
16" O.C.
16" O.C.
2 6 16" O.C.
This set of plans and specifications must be
kept on the job at all times and it is unlawful to ISSUED BY VOID
make any changes or alterations from the

PER PLAN
Community Development Department
(1) ROW 2X6 WOOD STUDS WITH OPTIONAL OVER FRAMING same without written permission from the 2X4 OR 2X6 (PER FLOOR PLAN) WOOD STUDS @ 16" O.C. ARCHITECTS, INC.
ONE LAYERS 58" GYPSUM WALLBOARD APPLIED AT RIGHT (AS REQUIRED PER FLOOR PLAN), 16" ON CENTER WITH 78"
ANGLES TO EACH SIDE OF 2X8 WOOD STUDS 16" O.C. WITH 2
Building Inspection Division. By: Ann Rosendale FACE SIDE: 58" TYPE "X" GYPSUM BOARD

812"
CEMENT PLASTER (MEASURED FROM FACE OF STUDS) ON The approval of this plan and specification MOISTURE-RESISTANT WHERE REQUIRED
1
4" TYPE "S" OR "W" DRYWALL SCREWS 7" O.C. VERTICAL THE EXTERIOR SURFACE AND (!) LAYER 58" GYPSUM on Jan 20, 2023 Faramarz Jabbari, AIA
SHALL NOT be held to permit or approve the
JOINTS STAGGERED 16" O.C. HORIZONTAL JOINTS WALLBOARD TYPE "X" ON THE INTERIOR SURFACE, 1 2

W6.10
violation of any City Ordinance or State Law.

W8.02 W4.01A
STAGGERED 24" O.C. ON OPPOSITE SIDES. MOISTURE RESISTANT WHERE REQUIRED.
5 12" BATT INSULATION STAPLED TO STUDS TO STUD SPACES. 7 1 4 3 5 2240
1 2 STRUCTURAL SHEATHING WHERE OCCURS PER
1HR EXTERIOR WALL WITH 1 2X6 WOOD STUDS Faraday Road
STRUCTURAL DRAWINGS. TYP. CAVITY PARTITION
NON RATED STUCCO FINISH AND OPTIONAL
ADDITIONAL LAYER OF 58" GYP. BOARD WHERE OCCURS AT 7 5 5 12" BATT INSULATION
INTERIOR PARTITION OVER FRAMING 2 8" CEMENT PLASTER
2HR RATED SHAFT CONTINUATION CONDITION. CORRIDOR
2 2X4 OR 2X6 WOOD STUDS 16" O.C.
5 OPTIONAL: SHEATHING 1 Carlsbad, California
1 2X8 WOOD STUDS 2 8" GYPSUM BOARD TYPE "X" 6 5
ONE LAYER TYPE "X" GYPSUM WALLBOARD OR GYPSUM 16" O.C.
5 PER STRUCTURAL DWGS. 8"
3 8"GYPSUM BOARD 92008
TYPE "X" VENEER BASE APPLIED OR AT RIGHT ANGLES, TO EACH
FIRE RATING SOUND RATING OPTIONAL: ADDITIONAL SIDE OF 2X4 WOOD STUDS 16" O.C. ON STAGGERED 8" O.C. 5 Tel: (858) 792-5997
FIRE RATING SOUND RATING 7 FIRE RATING SOUND RATING 2 8" TYPE "X" GYP. BD.
1-HR (EXPOSURE BOTH SIDES) N/A OPTIONAL: WOOD OVER LAYER 58" GYPSSUM ON 2X6 WOOD PLATES WITH 6D COATED NAILS, 1 78" LONG, N/A N/A Fax: (858) 792-5858

312" 11 2" 512"

N/A N/A 4 BOARD TYPE "X"
FRAMING PER PLAN 0.0915" SHANK, 41" HEADS, 7" O.C. -
- FIRE RESISTANCE PER TABLE 721.1(2) ITEM 15-1.3 SIM.
3
5 8" MIN. STRUCT. SHEATHING ON ONE SIDE OF STUDS, IF NO
TWO LAYERS TYPE "X" GYPSUM WALLBOARD OR GYPSUM
8"
16" O.C.
VENEER BASE APPLIED OR AT RIGHT ANGLES, TO EACH SHEATHING REQUIRED, PROVIDE ADDITIONAL LAYER OF 85"
TYPE 'X' GYPSUM WALLBOARD INSTEAD. 24" O.C. MAX. 09/12/2022
SIDE OF 2X4 WOOD STUDS 16" O.C. ON STAGGERED 8" O.C. A
2 5
W4.07A
CORRIDOR SECOND CITY SUBMITTAL
ON 2X6 WOOD PLATES WITH 6D COATED NAILS, 1 78" LONG, 2 3 21" BATT INSULATION IN BOTH STUD CAVITIES.
16" O.C. JOINTS STAGGERED 24" ON OPPOSITE SIDES. HORIZONTAL 10/26/2022
7 0.0915" SHANK, 14" HEADS, 7" O.C. (1) LAYER 58' TYPE "X" GYPSUM WALLBOARD OR GYPSUM

PER PLAN
(!) ROW 2X8 WOOD STUDS 16" ON CENTER WITH CEMENT 8" BRACING REQUIRED AT MID-HEIGHT. (LOAD-BEARING). UNIT B THIRD CITY SUBMITTAL

43 4"
PLASTER (MEASURED FROM FACE OF STUDS) ON THE
3
8 " MIN. STRUCT. SHEATHING ON ONE SIDE OF STUDS, IF NO OPTIONAL: LIGHT GAUGE PLUMBING WALL AND FINISH PER
4 1 3 5 VENEER BASE APPLIED PARALLEL OR AT RIGHT ANGLES TO
TYP. CORRIDOR WALL AT
EACH SIDE OF 2X4 WOOD STUDS AT 24" O.C., WITH 6D

83 8" MIN.
EXTERIOR SURFACE AND (1) LAYER 58" GYPSUM WALLBOARD SHEATHING REQUIRED, PROVIDE ADDITIONAL LAYER OF 58" KITCHEN OVER FRAMING PLAN WHERE OCCURS. 3
COATED NAILS, 1 78" LONG, 0.0915 SHANK, 14" HEADS, 7" O.C., ----
TYPE "X" ON THE INTERIOR SURFACE, MOISTURE RESISTANT TYPE 'X' GYPSUM WALLBOARD INSTEAD.
WHERE REQUIRED. 3 12" BATT INSULATION IN BOTH STUD CAVITIES. ONE HOUR FIRE RATING IS ACHIEVED WITHOUT THE JOINTS STAGGERED 24" ON OPPOSITE SIDES

W8.01 W4.01
INSULATION REQUIRED FOR ACOUSTICAL PURPOSES & (LOAD-BEARING).
2 1 4 ----
5 12" BATT INSULATION STAPLED TO STUDS IN STUD SPACES. JOINTS STAGGERED 24" ON OPPOSITE SIDES. HORIZONTAL 1 2X4 WOOD STUDS 4 SOUND BATT INSULATION
STRUCTURAL SHEATHING WHERE OCCURS PER 1 3 4 BRACING REQUIRED AT MID-HEIGHT. (LOAD-BEARING). STRUCTURAL SHEATING REQUIRED BY THE STRUCTURAL
OPTIONAL ENGINEER.

W6.07
STRUCTURAL DRAWINGS. OPTIONAL: LIGHT GAUGE PLUMBING WALL AND FINISH PER STRUCT. SHEATHING OR GLASS FIBER FIRE STOP 5 ----
8" EXTERIOR STUCCO WALL 2 5 4" NON RATED INTERIOR
1 2"X8" WOOD STUDS PLAN WHERE OCCURS. ADDITIONAL LAYER OF 58" AT 10"-0" INTERVALS BOTH
UNIT PARTITION
5 21" SOUND BATT STC RATING TEST # GYPSUM BOARD TYPE "X" VERT. & HORIZ.
6
TUB ADJACENT TO EXTERIOR 4 INSULATION ONE HOUR FIRE RATING IS ACHIEVED WITHOUT THE 4 1 6 5 3 2X4 WOOD STUDS
----
7 2-HR. RATED EXIT ENCLOSURE 52 NRC 93-226 (MODIFIED) 1
WALL OR GARAGE FACE WALL 8" CEMENT PLASTER INSULATION REQUIRED FOR ACOUSTICAL PURPOSES & 1 4 SOUND BATT INSULATION 5
2 2X4 WOOD STUDS FIRE RATING TEST # 3 8"GYPSUM BOARD TYPE
STRUCTURAL SHEATING REQUIRED BY THE STRUCTURAL "X" 7 ----
OPTIONAL: SHEATHING ENGINEER. 1HR GA FILE NO. WP 3371
5 5 PER STRUCTURAL DWGS.
STRUCT. SHEATHING OR GLASS FIBER FIRE STOP 2 5
FIRE RATING SOUND RATING 3 8"GYPSUM BOARD 2 5 ONE LAYER 58" TYPE "X" GYPSUM WALLBOARD OR GYPSUM
FIRE RATING SOUND RATING 1 LAYER 8" GYPSUM BOARD TYPE "X"
ADDITIONAL LAYER OF 58" AT 10"-0" INTERVALS BOTH 8 ----
1-HR (EXPOSURE BOTH SIDES) N/A TYPE "X" N/A N/A
STC RATING TEST # GYPSUM BOARD TYPE "X" VERT. & HORIZ. VENEER BASE APPLIED OR AT RIGHT ANGLES, TO EACH
FIRE RESISTANCE PER TABLE 721.1(2) ITEM 15-1.3 SIM. SIDE OF 2X4 WOOD STUDS 16" O.C. ON STAGGERED 8" O.C. -
52 NRC 93-226 (MODIFIED) DRAFTSTOPPING @ 10'-0" CORRIDOR 9 ----
5
FIRE RATING TEST # 3 8"GYPSUM BOARD TYPE 6 ON 2X6 WOOD PLATES WITH 6D COATED NAILS, 1 78" LONG, 2
O.C. MIN.
"X" 0.0915" SHANK, 41" HEADS, 7" O.C. 16" O.C.
16" 2HR GA FILE NO. WP 3371
ONE LAYER 85" TYPE "X" GYPSUM WALLBOARD APPLIED AT 3 ARIZONA # : 27259
16" O.C. 8" MIN. STRUCT. SHEATHING ON ONE SIDE OF STUDS, IF NO
RIGHT ANGLES TO ONE SIDE OF 2X6 WOOD STUDS 16 O.C.
5 4 6 BASE LAYER 58" TYPE "X" GYPSUM WALLBOARD OR GYPSUM SHEATHING REQUIRED, PROVIDE ADDITIONAL LAYER OF 85"

718" MIN.
EXTERIOR CALIFORNIA # : C15528
WITH 2 41" TYPE "S" OR "W" DRYWALL SCREWS 12" O.C. 5 12" VENEER BASE APPLIED AT RIGHT ANGLES TO ONE SIDE OF 5 SHAFT SIDE 2 TYPE 'X' GYPSUM WALLBOARD INSTEAD.
BATT INSULATION FIT IN STUD SPACE. 2X4 & 2X6 WOOD STUDS 16" O.C. (ON SEPARATE PLATES). 1" COLORADO # : 304356
3 21" BATT INSULATION IN BOTH STUD CAVITIES.
APART WITH 6D COATED NAILS, 1 78" LONG, 0.085" SHANK, 14" JOINTS STAGGERED 24" ON OPPOSITE SIDES. HORIZONTAL OREGON # : 5318
OPPOSITE SIDE: 38" MIN. STRUCT. SHEATHING, 58" TYPE "X"
71 8"

HEADS, 24" O.C. BRACING REQUIRED AT MID-HEIGHT. (LOAD-BEARING). OPTIONAL

GYPSUM WALLBOARD, BUILDING PAPER AND CORRUGATED NEVADA # : 2838

W4.07
OPTIONAL: LIGHT GAUGE PLUMBING WALL AND FINISH PER

1'-012"
METAL SIDING. 5 24"O.C. MAX. TEXAS # : 16533
FACE LAYER TYPE "X" GYPSUM WALLBOARD OR GYPSUM
8" PLAN WHERE OCCURS.
VERTICAL JOINTS STAGGERED 16" O.C. HORIZONTAL JOINTS

1"
UNIT VENEER BASE APPLIED AT RIGHT ANGLES TO EACH SIDE UNIT
STAGGERED 24" O.C. ON OPPOSITE SIDES. 3 2 1 4 1 6 5 3 UTAH # : 7288093-0301
WITH 8D COATED NAILS, 2 38" LONG, 0.100" SHANK, 14" HEADS, 8" ONE HOUR FIRE RATING IS ACHIEVED WITHOUT THE ONE LAYER 1" X 24" PROPRIETARY TYPE "X" GYPSUM 4

W6.05
TYP. CORRIDOR WALL

318 " MIN.

INSULATION REQUIRED FOR ACOUSTICAL PURPOSES & PANELS INSERTED BETWEEN 2 12" FLOOR AND CEILING WASHINGTON # : 8895

Y
SOUND BATT INSULATION

M2.08
TESTED AT 5,156 IBS PER STUD OR 100 PERCENT OF DESIGN O.C. 1 2X4 WOOD STUDS 4
STRUCTURAL SHEATING REQUIRED BY THE STRUCTURAL RUNNERS WITH T SECTION OF 2-1/2" STEEL C-T STUDS

R
LOAD. (LOAD-BEARING)
4 STRUCT SHEATHING JOINTS STAGGERED 16" EACH LAYER & SIDE. UNIT SIDE ENGINEER. STRUCT. SHEATHING OR GLASS FIBER FIRE STOP BETWEEN PANELS. ADDRESS:

W6.22
TA
2 HOUR SHAFT/UNIT DEMISING 3 4 1 2 5
1 2"X6" WOOD STUDS SOUND TESTED WITH 3 21" BATT INSULATION STAPLED TO ADDITIONAL LAYER OF 58" AT 10"-0" INTERVALS BOTH
WALL 1 GYPSUM BOARD TYPE "X" VERT. & HORIZ. 1HR SHAFT WALL W/O OPPOSITE SIDE: 3 1 2 1590 BARTLETT LN
STUDS IN STUD SPACES ON ONE SIDE & WITH NAILS FOR 2X4 WOOD STUDS STC RATING TEST #

E
5 BUILDING PAPER INSULATION ONE LAYER 58" PROPRIETARY TYPE X GYPSUM WALLBOARD SACRAMENTO, CA 95815

1548, 1554, 1560, 1566, 1572, 1578, 1584, & 1590 Bartlett
BASE LAYER SPACED 6" O.C. HORIZONTAL BRACING (2)LAYERS 68" GYPSUM 52 NRC 93-226 (MODIFIED) DRAFTSTOPPING @ 10'-0"
5
8"GYPSUM BOARD TYPE 4 5
APPLIED PARALLEL TO STUDS WITH 1" TYPE S DRYWALL
5
8"
GYPSUM BOARD 2 12" MIN. STEEL C-H OR C-T
ONE HOUR FIRE RATING IS ACHIEVED REGARDLESS OF 2 REQUIRED AT MID-HEIGHT. (LOAD-BEARING) 2X6 WOOD STUDS FIRE RATING TEST # 3 8"GYPSUM BOARD TYPE 6 1 3

R
"X" 2 BOARD TYPE"X" O.C. MIN. PROPRIETARY TYPE STUD
EXTERIOR FINISH MATERIAL PER TESTED ASSEMBLY, & THE "X" SCREWS 12" O.C.
STC RATING TEST # 1HR GA FILE NO. WP 3371

P
STRUCTURAL SHEATHING REQUIRED BY THE STRUCTURAL 1" AIR SPACE "X"

APPROVED
M2.08A
SOUND BATT CORRUGATED METAL 67 NRC 93-269 5
3 6 SOUND BATT SOUND TESTED WITH RESILIENT CHANNELS 24" O.C. AND GLASS FIBER SOUND 1" PROPRIETARY TYPE "X"

O
ENGINEER. SIDING 3
INSULATION FIRE RATING TEST # 2-1/2" GLASS FIBER FRICTION FIT IN STUD SPACE. (NLB) 2 INSULATION 4
INSULATION ONE LAYER 58" GYPSUM WALLBOARD OR GYPSUM VENEER GYP. PANEL City of Sacramento Plan Review

R LIFE SAFETY
2 HOUR GA FILE NO. WP 3820 BASE APPLIED PARALLEL OR AT RIGHT ANGLES, TO EACH 5 (OPTIONAL - AT M2.08A

P
SIDE OF DOUBLE ROW OF 2X4 WOOD STUDS 16" O.C. ON 1HR ACOUSTIC FOR ACOUSTIC)
16" O.C.
STC RATING TEST # SEPARATE PLATES 1" APART WITH 6D COATED NAILS, 1 78" UNIT FIRE RATING SOUND RATING
PROPRIETARY GYPSUM PANEL PRODUCTS: By: Mark K. Harris II
44 WEAL 07-353 2 LONG, 0.0915" SHANK, 14" HEADS, 7" O.C. PABCO GYPSUM 58" FLAME CURB SUPER 'C' TYPE C 1"
FIRE RATING TEST #
1HR 45 TO 49 STC
PABCORE GYPSUM LINER BOARD on Dec 13, 2022
3 12" BATT INSULATION STAPLED TO STUDS IN STUD SPACES 16" O.C. GA FILE NO. WP 6800
1 HOUR GA FILE NO. WP 3661
ON ONE SIDE.
24" O.C. MAX. (1) ROW 2X6 WOOD STUDS - HORIZONTAL BLOCKING @ JOINTS STAGGERED 16" ON OPPOSITE SIDES. HORIZONTAL
EXTERIOR SIDE - ONE LAYER 58" TYPE "X" GYPSUM 2

112"
75 8"
MID-HEIGHT W/ (1) LAYER GYP. BD. ONE SIDE FULL WALL TO

1'-21 4"
WALLBOARD, WATER-RESISTANT GYPSUM BACKING BOARD, BRACING REQUIRED AT MID-HEIGHT. (LOAD-BEARING)
7 DECK ABOVE. (DRAFT STOPS ARE FIBERGLASS INSULATION)
OR GYPSUM VENEER BASE APPLIED PARALLEL OR AT RIGHT

D E V E L O P M E N T
ANGLES TO 2X6 STUDS OR OPTIONAL OVERFRAMING (AS OPTIONAL: LIGHT GAUGE SKID WALL AND FINISH PER PLAN

1"
W4.05A
OPPOSITE SIDE: 58" TYPE "X" GYPSUM BOARD

W6.04
WHERE OCCURS.
PER PLAN

REQUIRED PER PLANS) WITH 6D COATED NAILS, 1 78" LONG, 3 4 5 8"X8"X16" 3-CELL LIGHTWEIGHT CONCRETE MASONRY
MOISTURE-RESISTANT, 5/8" DENSSHIELD TILE BACKER & 14" 1 UNITS.
0.0915" SHANK, 41" HEADS, 7" O.C. (LOAD-BEARING).
THIN SET CERAMIC TILE. ADDITIONAL LAYER OF 58" TYPE "X" GYP. BOARD. TO BE REFER TO STRUCTURAL DRAWINGS FOR WALL THICKNESS
BATT INSULATION STAPLED TO STUDS IN STUD SPACES PER 6 UNIT

75 8"
6" INTERIOR PARTITION W/TILE TYPICAL DEMISING WALL AT PROVIDED @ BEDROOM TO BEDROOM, BEDROOM TO AND REINFORCEMENT.
ENERGY CALCULATIONS.
NOTE: PRIMARY 5 8" TYPE "X" GYPSUM BOARD IS ONLY 2"X6" WOOD STUDS KITCHEN OVER FRAMING LIVING/DINING ROOM.
(1) LAYER 58" GYPSUM WALLBOARD TYPE "X" ON THE INTERIOR AT TUB/SHOWER 1 3 4 2 1
REQUIRED AT RATED WALLS.

W6.15
1HR EXTERIOR WALL WITH
SURFACE, MOISTURE RESISTANT WHERE REQUIRED.
5 12" BATT INSULATION STAPLED TO STUDS IN STUD SPACES.
STRUCTURAL SHEATHING WHERE OCCURS PER 1 2X6 WOOD STUDS 1 4 3 5 2
16" O.C.
5
8" GYP. BD. TYPE "X"
4
5
8"

1
DENSHIELD TILE
BACKER
(PLACE ADDITIONAL LAYER OF GYP. BD. ON SHORTER RM.
SIDE)

ONE HOUR FIRE RATING IS ACHIEVED WITHOUT THE 1 2X4 WOOOD STUDS 4 1" AIR GAP
C8.01
8" CMU WALL
STRUCTURAL DRAWINGS. 4" THIN SET CERAMIC TILE

GATEWAY
PANELIZED FINISH OPTIONAL EXTERIOR FINISH 5 5 12" BATT INSULATION FIRE RATING SOUND RATING 5 INSULATION REQUIRED FOR ACOUSTICAL PURPOSES. 5

VILLAGE-PHASE 2
2 5 8"GYPSUM BOARD REFER TO CHAPTER 7 OF THE CODE FOR RATED C.M.U
3 8"
GYP.BD. DRAFTSTOPPING @ 10'-0"
RAIN SCREEN AND OPTIONAL MATERIAL PER ELEVATION N/A N/A
MOISTURE-RESISTANT
2 TYPE "X" 5 ASSEMBLIES, OR EQUIVALENT THICKNESS CALCULATIONS.
5 O.C. MIN.
OVER FRAMING 8"GYPSUM SHEATHING -
5 6 FIRE RATING SOUND RATING SOUND BATT
8"GYPSUM BOARD TYPE "X"
FIRE RATING SOUND RATING 3 1HR 58 STC 3 INSULATION
TYPE "X" OPTIONAL 34" AIR GAP/
1-HR (EXPOSURE TO N/A 7 24" O.C. MAX. GA FILE NO. WP 3370 NRC 93-263
RAIN-SCREEN OVER BASE LAYER 5/8" TYPE "X" GYPSUM WALLBOARD OR

APARTMENTS
OPTIONAL: WOOD OVER
BOTH SIDES) 4 WATERPROOFING GYPSUM VENEER BASE APPLIED AT RIGHT ANGLES TO EACH FIRE RATING SOUND RATING
FRAMING PER PLAN
GA FILE NO. WP 8105 MEMBRANE/AIR BARRIER SIDE OF 2X6 WOOD STUDS AT 24" O.C., WITH 6D COATED ONE LAYER 58" GYPSUM WALLBOARD OR GYPSUM VENEER - -

SACRAMENTO, CALIFORNIA
UNIT
NAILS, 1 7/8" LONG, 0.085" SHANK, 1/4" HEADS, 24" O.C. BASE APPLIED PARALLEL OR AT RIGHT ANGLES, TO EACH 5 6
SIDE OF DOUBLE ROW OF 2X4 WOOD STUDS 16" O.C. ON
16" FACE LAYER 58" TYPE "X" GYPSUM WALLBOARD OR GYPSUM SEPARATE PLATES 1" APART WITH 6D COATED NAILS, 1 78" 16" O.C. OPTIONAL 24"O.C. MAX.
VENEER BASE APPLIED AT RIGHT ANGLES TO EACH SIDE LONG, 0.0915" SHANK, 14" HEADS, 7" O.C.

8"
1 2 WITH 8D COATED NAILS, 2 38" LONG, 0.100" SHANK, 14" HEADS, 3 12" BATT INSULATION STAPLED TO STUDS IN STUD SPACES

W6.03 8" O.C. ON ONE SIDE. ONE LAYER 58" TYPE "X" GYPSUM WALLBOARD APPLIED

47 8"
91 4"
PARALLEL TO EACH SIDE OF 3 58" STEEL STUDS 24" O.C. WITH

1"
JOINTS STAGGERED 24" EACH LAYER AND SIDE. SOUND JOINTS STAGGERED 16" ON OPPOSITE SIDES. HORIZONTAL
71 4"

TESTED WITH STUDS 16" O.C. AND WITH NAILS FOR BASE 3 BRACING REQUIRED AT MID-HEIGHT. (LOAD-BEARING) 1" TYPE "S" DRYWALL SCREWS 8" O.C. AT VERTICAL JOINTS
2HR INTERIOR PARTITION 1 2
LAYER SPACED 6" O.C. (LOAD-BEARING) (DRAFT STOPS ARE FIBERGLASS INSULATION) AND 12" O.C. AT FLOOR AND CEILING RUNNERS AND

W6.14
(1) ROW 2X6 WOOD STUDS 16" ON CENTER WITH 7/8"
CEMENT PLASTER (MEASURED FROM FACE OF
STUDS) ON BOTH SIDES.
PLASTER MIX 1:4 FOR SCRATCH COAT AND 1:5 FOR
OPTIONAL: INSULATION FIT IN STUD SPACE. 1 2"X6" WOOD STUDS 24" O.C.
W4.05
TYPICAL DEMISING WALL
OPTIONAL: LIGHT GAUGE SKID WALL AND FINISH PER PLAN
WHERE OCCURS.
5
ADDITIONAL LAYER OF TYPE "X" GYP. BOARD. TO BE
8" 3
UNIT

4 2 1 M4.01
INTERMEDIATE STUDS.

STAGGER JOINTS 24" ON EACH SIDE AND ON OPPOSITE

SIDES.
1 2

2 (2) LAYER 58" GYPSUM BOARD TYPE "X" PROVIDED @ BEDROOM TO BEDROOM, BEDROOM TO
(2X6 EXTERIOR BROWN COAT, BY VOLUME, CEMENT TO SAND. 3 5
LIVING/DINING ROOM. 8" NON RATED INTERIOR
FIRE RATING SOUND RATING
WALL AT (PLACE ADDITIONAL LAYER OF GYP. BD. ON SHORTER RM. 2X4 WOOOD STUDS 4 1" AIR GAP PARTITION
BREEZEWAY) 2HOUR 40 TO 44 STC 3 OPTIONAL: INSULATION IN STUD BAY 1
1 2X6 WOOD 2 7/8" CEMENT SIDE)
ONE HOUR FIRE RATING IS ACHIEVED WITHOUT THE 3 85" STEEL STUDS
STUDS PLASTER GA FILE NO. WP 4153 5 1
INSULATION REQUIRED FOR ACOUSTICAL PURPOSES. 8"GYPSUM BOARD DRAFTSTOPPING @ 10'-0"
ONE LAYERS 58" GYPSUM WALLBOARD APPLIED AT RIGHT 2 5

D E B A R T O L O
TYPE "X" O.C. MIN.
ANGLES TO EACH SIDE OF 2X6 WOOD STUDS 16" O.C. WITH 2 FIRE RATING SOUND RATING SOUND BATT OPTIONAL: LIGHT GAUGE FIRE RATING SOUND RATING 2 1 LAYER 58" GYPSUM BOARD TYPE "X"
1 16" O.C.
4 " TYPE "S" OR "W" DRYWALL SCREWS 7" O.C. VERTICAL 1HR 58 STC 3 INSULATION 6 SKID WALL AND FINISH PER - -
JOINTS STAGGERED 16" O.C. HORIZONTAL JOINTS 3 PLAN W.O.
GA FILE NO. WP 3370 NRC 93-263 -
STAGGERED 24" O.C. ON OPPOSITE SIDES.
2 24"O.C. MAX.
16" O.C. ONE LAYER 1" X 24" PROPRIETARY TYPE "X" GYPSUM
7 TESTED AT 5,156 LBS PER STUD OR 100 PERCENT OF DESIGN
63 4"

LOAD. (LOAD-BREAKING). PANELS INSERTED BETWEEN 2 12" FLOOR AND CEILING "J" 4
16" O.C.

33 4" MIN.
RUNNERS WITH T SECTION OF 2 12" (MINIMUM) STEEL C-H

M2.02
PER PLAN

6 OPTIONAL:

W6.02
(1) ROW 2X6 WOOD STUDS WITH OPTIONAL OVER FRAMING OR C-T STUDS BETWEEN PANELS.

Y
(AS REQUIRED PER FLOOR PLAN), 16" ON CENTER WITH FULL BATT INSULATION STAPLED TO STUDS IN STUD SPACES PER

ARDEN
R
DEPTH 78" SCRATCH AND BROWN CEMENT PLASTER ENERGY CALCULATIONS. 1 4 2 OPPOSITE SIDE:
OPTIONAL: 2X4 OR 2X6 (PER FLOOR PLAN) WOOD STUDS @ 16" O.C. ,

A
(MEASURED FROM FACE OF STUDS) AND CAST FIT CULTURED 5 5
2HR SHAFT WALL W/O BASE LAYER 58" PROPRIETARY TYPE "X" GYPSUM 3 1 2
ADDITIONAL LAYER OF 58" TYPE "X" GYP. BD. SHOWN IN 8" TYPE "X" GYPSUM BOARD MOISTURE-RESISTANT, 8 "

T
STONE ON THE EXTERIOR SURFACE AND (1) LAYER 58" 1HR RATED INTERIOR INSULATION WALLBOARD APPLIED AT RIGHT ANGLES TO STUDS WITH 1"
1 2"X6" WOOD STUDS 3 OPTIONAL: DENSHIELD TILE BACKER & 41" THIN SET CERAMIC TILE. 3 4 2 1 5
2 12" MIN. STEEL C-H OR C-T

W6.12
PARTITION/ BEARING WALL DOTTED TO BE PROVIDED WHERE OCCURS. 8" GYPSUM BOARD

E
TYPE "s" DRYWALL SCREWS 24" O.C. FACE LAYER 58"

W4.04A
GYPSUM WALLBOARD TYPE "X" ON THE INTERIOR SURFACE, 1 3

I
5
8 " GP. BD. (ADDITIONAL PROPRIETARY TYPE STUD
MOISTURE RESISTANT WHERE REQUIRED.
1 2X6 WOOD STUDS 1 4 3 5 1 1 PROPRIETARY TYPE "X" GYPSUM WALLBOARD APPLIED
LAYER) 4" THIN SET CERAMIC TILE

R
"X"
5 21" BATT INSULATION STAPLED TO STUDS IN STUD SPACES. PARALLEL TO STUDS WITH 1 58" TYPE "S" DRY/WALL

M2.02A
5
NOTE: PRIMARY 8" TYPE "X" GYPSUM BOARD IS ONLY
1 GLASS FIBER SOUND

P
1HR EXTERIOR WALL WITH STRUCTURAL SHEATHING WHERE OCCURS PER 7 5 2" BATT INSULATION STC RATING TEST # 5 1" PROPRIETARY TYPE "X"
2 8"SCRATCH AND BROWN 5 2 5
8"GYPSUM BOARD TYPE 4 OPTIONAL: CAVITY PARTITION W/TILE AT REQUIRED AT RATED WALLS 2 8"
TYPE "X" GYP. BD. SCREWS 12" O.C. 2 INSULATION 4
BRICK FINISH AND OPTIONAL STRUCTURAL DRAWINGS. CEMENT PLASTER (FULL 34 OCF 424 GYP. PANEL

O
"X" BATT INSULATION PER TUB/SHOWER MOISTURE-RESISTANT
OVER FRAMING OPTIONAL: IN LIEU OF STONE, APPLY FINISH PER EXTERIOR OPTIONAL: SHEATHING FIRE RATING (OPTIONAL - AT M2.02A
DEPTH REQUIRED FOR TEST # ENERGY CALCS SOUND TESTED WITH 1 78" GLASS FIBER INSULATION IN

PR
ELEVATIONS (TILE OR SIMILAR). FIRE RATING) 6 PER STRUCTURAL DWGS. 1HR GA FILE NO. WP 3660 2X4 OR 2X6 WOOD 2HR ACOUSTIC FOR ACOUSTIC)
3 STUD SPACE. (NLB)
5 STUDS 16" O.C.
3 8"GYPSUM BOARD CAST FIT CULTURED
FIRE RATING SOUND RATING TYPE "X" 7 STONE OR OPTIONAL TILE 5 PROPRIETARY GYPSUM PANEL PRODUCTS:
4 8 " DENSHIELD TILE FIRE RATING SOUND RATING
1-HR (EXPOSURE BOTH SIDES) N/A OPTIONAL: WOOD OVER FINISH PER EXT. 16" O.C. FIRE RATING SOUND RATING BACKER GEORGIA-PACIFIC GYPSUM LLC 58" TOUGHROCK FIREGUARD X
4 ELEVATIONS N/A N/A
2HR 50 TO 54 STC
GYPSUM BOARD 1" DENSGLASS SHAFTLINER
FRAMING PER PLAN
FIRE RESISTANCE PER TABLE 721.1(2) ITEM 15-1.3 SIM. GA FILE NO. WP 7054
-
16" O.C. ONE LAYERS 58" GYPSUM WALLBOARD APPLIED AT RIGHT

VARIES PER STRUCTURAL

2 6 16" O.C.
REINFORCED CONCRETE STRUCTURE PER STRUCTURAL
ANGLES TO EACH SIDE OF 2X6 WOOD STUDS 16" O.C. WITH 2
63 4"

1 1 DRAWINGS.
4 " TYPE "S" OR "W" DRYWALL SCREWS 7" O.C. VERTICAL
FIRE RESISTANCE PER TABLE 721. 1(2):
JOINTS STAGGERED 16" O.C. HORIZONTAL JOINTS
MINIMUM THICKNESS FOR 1-HOUR RATING: 3.5"

W6.01
C (1) ROW 2X6 FIRE RETARDANT -TREATED WOOD STUDS STAGGERED 24" O.C. ON OPPOSITE SIDES.
PER PLAN

MINIMUM THICKNESS FOR 2-HOUR RATING: 5"

8"
WITH OPTIONAL WOOD OVER FRAMING (AS REQUIRED PER (1) ROW 2X4 WOOD STUDS 16: O.C. - HORIZONTAL BLOCKING 24"O.C.

55
@ MID-HEIGHT W/ (1) LAYER GYP. BD. ONE SIDE FULL WALL MINIMUM THICKNESS FOR 3-HOUR RATING: 6.2"
FLOOR PLAN) 16" ON CENTER WITH 78" CEMENT PLASTER 1 2

W6.11 (MEASURED FROM FACE OF STUDS) OVER 58" TYPE "X"

GYPSUM SHEATHING ON THE EXTERIOR SURFACE AND (2) NON RATED
TO DECK ABOVE.

OPPOSITE SIDE: 58" TYPE "X" GYPSUM BOARD

3 4 2 5
MINIMUM THICKNESS FOR 4-HOUR RATING: 7"
*SEE FIRE RESISTANCE RATING PERIODS TABLE FOR
ACTUAL MIN. THICKNESS DEPENDANT UPON

W4.04 M1.01
INTERIOR PARTITION
2HR EXTERIOR WALL WITH LAYERS 58" GYPSUM WALLBOARD TYPE "X" ON THE INTERIOR 5 1
CONSTRUCTION MATERIALS & METHODS
MOISTURE-RESISTANT, 8" DENSHIELD TILE BACKER & 4" THIN
STUCCO FINISH AND OPTIONAL SURFACE, MOISTURE RESISTANT WHERE REQUIRED. 1 2X6 WOOD STUDS 2 5 FINISH: 78" METAL FURRING CHANNEL @ 24" O.C.
8" GYPSUM BOARD TYPE "X" SET CERAMIC TILE.
OVER FRAMING 5 12" BATT INSULATION STAPLED TO STUDS IN STUD SPACES. 1 4 3 5 ONE LAYER 58" TYPE "X" GYPSUM BOARD 2 1 3
4" INTERIOR PARTITION W/TILE 1 5 CONCRETE WALL WITH
NOTE: PRIMARY 5 8" TYPE "X" GYPSUM BOARD IS ONLY 8" GYP. BD. TYPE "X"
FIRE-RETARDANT OPTIONAL: WOOD OVER FIRE RATING SOUND RATING AT TUB/SHOWER FURRING NOTE: MAINTAIN CONCRETE WALL PLUM WITHIN INDUSTRY
1 4 FRAMING PER PLAN REQUIRED AT RATED WALLS 4
5
8"DENSHIELD TILE
TREATED 2X6 WOOD N/A N/A 5 STANDARDS. IF WALL PLUM IS NOT WITHIN INDUSTRY
8"
TYPE "X" GYP. BD. BACKER 5 CAST IN PLACE
STUDS - 2
MOISTURE-RESISTANT
STANDARDS CONTACT ARCHITECT FOR ALTERNATIVE WALL 1 1 LAYER 8" GYPSUM 3 CONCRETE WALL
BOARD TYPE "X" MILESTONE:
5 1 1 ASSEMBLY.
2" BATT INSULATION 4" THIN SET CERAMIC TILE
7
2 8" CEMENT PLASTER 5 5 THIRD CITY SUBMITTAL
FIRE RATING SOUND RATING 2X4 WOOD STUDS 16"
FIRE RATING SOUND RATING 3 O.C. FIRE RATING SOUND RATING 7
8"
METAL FURRING
5
2-HR (EXPOSURE BOTH SIDES) N/A 3 (2) LAYERS 58" GYPSUM 6 8"GYPSUM SHEATHING
1HR, 2HR, 3HR, OR 4HR -
2
TYPE "X" N/A N/A CHANNELS
BOARD TYPE "X" (2) LAYERS 1" X 24" PROPRIETARY TYPE X GYPSUM PANELS

COM-2213627 to COM-2213634
FIRE RESISTANCE PER TABLE 721.1(2) ITEM 15-1.6 - -
ASSEMBLEY
2-HR RATED

INSERTED BETWEEN 2" FLOOR AND CEILING RUNNERS WITH 2" DRAWN: MH, NM
STEEL H STUDS BETWEEN ADJACENT PAIRS OF GYPSUM
PANELS. REINFORCED CONCRETE STRUCTURE PER STRUCTURAL
CHECKED: JM
BASE LAYER 5/8" TYPE "X" GYPSUM WALLBOARD OR 24" O.C. MAX. DRAWINGS.
GYPSUM VENEER BASE APPLIED AT RIGHT ANGLES TO EACH FIRE RESISTANCE PER TABLE 721. 1(2):

Y
3 PLOT DATE: Monday, October 24, 2022
3 A MINIMUM AIR SPACE MUST BE MAINTAINED BETWEEN
4"

VARIES PER STRUCTURAL

SIDE OF 2X4 WOOD STUDS AT 24" O.C., WITH 6D COATED MINIMUM THICKNESS FOR 1-HOUR RATING: 3.5"
1'-01 4"

R
UNIT STEEL COMPONENTS AND ADJACENT FRAMING.
4"

NAILS, 1 7/8" LONG, 0.0915' SHANK, 1/4" HEADS, 24" O.C. MINIMUM THICKNESS FOR 2-HOUR RATING: 5"

A
FACE LAYER 58" TYPE "X" GYPSUM WALLBOARD OR GYPSUM MINIMUM THICKNESS FOR 3-HOUR RATING: 6.2" E D A RC

6"
SOUND TESTED WITH 2X4 STUD WALL FACED WITH 21"
ER

T
VENEER BASE APPLIED AT RIGHT ANGLES TO EACH SIDE MINIMUM THICKNESS FOR 4-HOUR RATING: 7"
REGULAR GYPSUM WALLBOARD EACH SIDE OF SYSTEM AND
R Z JA

H
ST
W4.12
*SEE FIRE RESISTANCE RATING PERIODS TABLE FOR

IE
WITH 8D COATED NAILS, 2 38" LONG, 0.100 ' SHANK, 14" HEADS,
3- 21" GLASS FIBER INSULATION IN STUD SPACE ON BOTH MA B

IT E
ACTUAL MIN. THICKNESS DEPENDANT UPON

R EG I
1 8" O.C.

W4.03 C1.01

FA RA
3 2 1

R
SIDES. CONSTRUCTION MATERIALS & METHODS

BA
JOINTS STAGGERED 24" EACH LAYER AND SIDE. SOUND

CT
P
TESTED WITH STUDS 16" O.C. AND WITH NAILS FOR BASE

RI
2-HR FIRE WALL HEIGHT LIMITATION 66 FEET. 1 2 4 3 1 2X4 WOOD STUDS
No. C 15528

THIRD CITY SUBMITTAL 10/26/2022

LAYER SPACED 6" O.C. TYPICAL WATERPROOFING SYSTEM W/ VAPOR BARRIER

RO
2HR RATED INTERIOR WALL (LOAD-BEARING). CONCRETE WALL FOR ALL CONCRETE WALLS BELOW GRADE. WIDTH &
PROPRIETARY GYPSUM BOARD REINFORCING PER STRUCTURAL DRAWING Exp. 03/31/23
________
OPTIONAL: 3 21" BATT INSULATION 2 (2) LAYER 58" GYPSUM BOARD TYPE "X"
NATIONAL GYPSUM "GOLD BOND" 1" SHAFTLINER, 85" OUTER

P
1 2"X4" WOOD STUDS 3 1
ENTRY DOOR 3 SOUND BATT
2" TA

IA
*SEE ALTERNATE FINISH CONDITIONS @ CONCRETE WALLS N

S
GYP. BD. IS NON-PROPRIETARY TE
3 2 5 4 6
INSULATION.
3 OPTIONAL: BATT INSULATION ADJACENT TO FRAMED WALLS O F CA L I F O R
@ UNIT PLANS CORRIDOR
STC RATING TEST #
2 5
1" SHAFT LINER
60 TO 64 GA FILE # ASW 0981 & ASW 0998 8" GYPSUM BOARD TYPE "X" 4 FIRE RATING SOUND RATING FIRE RATING SOUND RATING
FIRE RATING 2HOUR 40 TO 44 STC 1HR, 2HR, 3HR, OR 4HR -
ENLARGED PLAN GA FILE NO. WP 4135 -
B 2HR PROJECT NO. 2021-051

16" O.C. PROJECT PHASE .

1 2X4 WOOD 5
SOUND BATT BREEZEWAY
(1) LAYER 5/8" TYPE "X" GYPSUM WALLBOARD OR
GYPSUM VENEER BASE APPLIED PARALLEL OR AT
24" O.C. MAX.
3
GENERAL NOTES WALL TYPE LEGEND SHEET TITLE
7 STUDS 16" O.C. INSULATION RIGHT ANGLES TO EACH SIDE OF 2X4 WOOD STUDS 1. WALL STUD SIZE, SPACING AND CONSTRUCTION ASSEMBLY TO BE
(1) ROW 2X4 WOOD STUDS 16" O.C.-3 21" SOUND BATT
AT 24" O.C., WITH 6D COATED NAILS, 1 7/8" LONG, COORDINATED W/ STRUCTURAL. WHERE STRUCTURAL SHOW STUD SIZES
INSULATION IN STUD SPACE.
43 4"
5"

2X6 2X4 STAGGERED 0.0915' SHANK, 1/4" HEADS, 7" O.C., DIFFERENT FROM ARCHITECTURAL, THE LARGER STUD SIZES ARE TO BE
6 7
2 8 " CEMENT PLASTER (MEASURED FROM FACE OF STUDS) ON
UNIT WOOD STUD STUD ASSEMBLY
THE EXTERIOR SURFACE. UNIT
JOINTS STAGGERED 24" ON OPPOSITE SIDES
(LOAD-BEARING).
USED. STUD SPACING @ 16" UNLESS NOTED BY STRUCTURAL OR WALL TYPE
DESCRIPTION WHICH REPRESENTS THE MAXIMUM ALLOWED STUD SPACING. W4.12 W6.09 WALL SCHEDULE
2X4 WALL OPPOSITE SIDE: (1) LAYER 58" TYPE "X" GYPSUM WALLBOARD

W4.09 W4.02
7
3 5/8" GYPSUM 7
TYPICAL OR GYPSUM VENEER BASE APPLIED AT RIGHT ANGLES TO OPTIONAL: 4 2 1 2. STRUCTURAL SHEATHING TO BE PER STRUCTURAL DRAWINGS AND IS NOT
WALL MATERIAL
BOARD TYPE "X" STUDS WITH 6D NAILS 8" O.C. 2 1 4 3 BATT INSULATION STAPLED TO STUDS IN STUD SHOWN (OR SHOWN AS OPTIONAL) IN THE WALL GRAPHICS/DESCRIPTION
SPACES PER ENERGY CALCULATIONS.
1 2X4 WOOD STUDS (WOOD FRAMING)
UNLESS PART OF THE REQUIRED ASSEMBLY.
3/8" 1HR BREEZEWAY WALL AT PLASTER MIX. : 1:4 FOR SCRATCH COAT AND 1;5 FOR BROWN 1HR RATED INTERIOR OPTIONAL:
WALL FRAMING
CORRIDOR 4 STRUCTURAL UNIT ENTRY COAT BY VOLUME, CEMENT TO SAND. PARTITION/ BEARING WALL ADDITIONAL LAYER OF 5/8" TYPE "X" GYP. BD. 3. GYPSUM BOARD TO BE MINIMUM 58" THICK. SHEET NO.
2 1 LAYER 58" GYPSUM BOARD TYPE "X" SIZE, (2X4 STUD)
TYP.

SHEATHING SHOWN IN DOTTED TO BE PROVIDED WHERE

1'-6"

A8-1.0
2X4 STUDS 16" O.C 5/8 " GYPSUM BOARD OCCURS. W: WOOD FRAMING
1 3 4. ALL GYPSUM BOARD EXPOSED TO MOIST AREAS TO BE WATER RESISTANT WALL FRAMING
TYPE "X" 3 OPTIONAL: GYPSUM (GREEN BOARD). M: METAL STUDS SIZE, (2X6 STUD)
5
7 8 " GP. BD. (ADDITIONAL LAYER) C: CONCRETE
2 8" CEMENT PLASTER 3 21" SOUND BATT
ENTRY DOOR B FIRE RATING SOUND RATING 4 FIRE RATING SOUND RATING 5. ALL GYPSUM BOARD JOINTS TO BE FIRE TAPED. F: FENCE WALL TYPE NO.
INSULATION OPTIONAL:
6 A 6
- 1HR (EXPOSURE BOTH SIDES) N/A 1HOUR N/A 4
BATT INSULATION PER ENERGY CALCS 6. STAIR WALLS ARE TO BE DOUBLE STUD WITH INSULATION IN BOTH BAYS.
FIRE RESISTANCE PER TABLE 721.1(2) ITEM 15-1.4 GA FILE NO. WP 3510
 48" MIN. 48" MIN.
X

JOB COPY
Y SIDEWALK SIDEWALK
GENERAL PROVISIONS & DEFINITIONS: SLOPE=Y:X POLE POLE
70 SQ. INCH. ACCESSIBILITY SIGN B 36" MIN. 36" MIN.
BACK OF WHERE X IS CLEAR CLEAR
PER SECTION 1109A.8.8
A LEVEL FACE OF FACE OF
ALL IDEAS, DESIGN ARRANGEMENTS AND PLANS INDICATED OR REPRESENTED BY THIS DRAWING ARE OWNED BY AND THE PROPERTY OF ARK ARCHITECTS, INC. AND WERE CREATED EVOLVED AND DEVELOPED FOR USE ON AND IN CONNECTION WITH THE SPECIFIED PROJECT. NONE OF SUCH IDEAS ARRANGEMENTS OR PLANS SHALL BE USED BY OR DISCLOSED TO ANY PERSON FIRM OR CORPORATION FOR ANY PURPOSE WHATSOEVER WITHOUT THE WRITTEN PERMISSION OF ARK ARCHITECTS, INC.
WHEEL
NOTE:
1. REFER TO SHEETS A9-1.5 FOR RESIDENTIAL
UNIT ACCESSIBILITY REQUIREMENTS.
STOP 48"
MIN.
SIDEWALK
PLANE
PLANTING OR
CURB CURB
A R K

MAX.
2. ALL INFORMATION IS BASED ON C.B.C. 2019 WALK FOR DETECTABLE OTHER

2%
WHEEL

MIN.
NON-WALKING STREET STREET

48"
12"
COVERED MULTIFAMILY DWELLINGS STOP STREET WARNING
SURFACE
1. BUILDINGS THAT CONSIST OF AT LEAST FOUR (4) CONDOMINIUM DWELLING UNITS OR AT LEAST THREE (3) APARTMENT
FULL HEIGHT/42"
REQUIREMENTS AT ARCHITECTS, INC.
DWELLING UNITS IF THE BUILDINGS HAVE AT LEAST ONE (1) ELEVATOR. CURB RAMPS, SEE
BARRIER WALL MEASUREMENT OF CURB RAMP SLOPES
SECTION 1127B.5,
STRIPES STRIPES (FIG. 11B-20E)
2. THE GROUND FLOOR DWELLING UNITS IN BUILDINGS THAT CONSIST OF AT LEAST FOUR (4) CONDOMINIUM DWELLING UNITS ITEM #7

8.33 %
AT 36" ON AT 36" ON " Faramarz Jabbari, AIA

MAX.
OR AT LEAST THREE (3) APARTMENT DWELLING UNITS IF THE BUILDING DOES NOT HAVE AN ELEVATOR. 48 IN. 11A-5A (a) SIDEWALK OBSTRUCTIONS
CENTER CENTER TOP OF M
SIDE WALK

.
COVERED MULTIFAMILY DWELLINGS INCLUDE DWELLINGS LISTED IN SECTION 1102A.1. FOR PURPOSES OF THIS DEFINITION, RAMP
48" HANDRAIL 2" MIN. CURB OR 2" TO 4" BARRIER
DWELLING UNITS WITHIN A SINGLE STRUCTURE SEPARATED BY FIREWALLS DO NOT CONSTITUTE SEPARATE BUILDINGS. 5'-0" MIN. AT TYP. 8.33 % 1'-0" 2240
5'-0" MIN. AT TYP. MIN. 12 CENTERED ON BOTH SIDES ABOVE

18'-0"

18'-0"
ACCESSIBLE MAX.

MIN.

MIN.
10 % MAX.

30" MAX. RAMP RISE

ACCESSIBLE 1 THE SURFACE OF THE RAMP OR 1'-0" Faraday Road
ACCESSIBLE DIMENSION TO PARKING STALL 8'-0" DIMENSION TO SIDE WALK
PARKING STALL 8'-0" 2 % MAX. 4 RAMP LANDING
A SITE, BUILDING, FACILITY, OR PORTION THEREOF THAT IS APPROACHABLE AND USABLE BY PERSONS WITH DISABILITIES IN CENTERLINE OF MIN. AT VAN CENTERLINE OF
MIN. AT VAN SEE GROOVING MI 8"
COMPLIANCE WITH THIS CODE. STRIPE TYPICAL ACCESSIBLE STRIPE TYPICAL N.
B DETAIL "11A-3K"
PARKING STALL ACCESSIBLE Carlsbad, California
SECTION A - A

34" TO 38"
PARKING STALL

2" TO 4"
ACCESSIBILITY 9'-0" . 9'-0" 9'-0" . (a) 92008
IS THE COMBINATION OF VARIOUS ELEMENTS IN A BUILDING OR AREA WHICH ALLOWS ACCESS,CIRCULATION AND THE FULL USE MIN. MIN. PLAN Tel: (858) 792-5997
MIN. WITHIN THE LOADING TOP OF
OF THE BUILDING AND FACILITIES BY PERSONS WITH DISABILITIES. & UNLOADING ACCESS 48" CL
RAMP
ACCESSIBLE ROUTE
NO NO AISLE PAINT THE 8.33 % MIN. 48" 1:12 MAX. CL
Fax: (858) 792-5858

WORDS "NO PARKING" MAX. 2 % MAX. MIN. 1:20 MAX.

IS A CONTINUOUS AND UNOBSTRUCTED PATH CONNECTING ALL ACCESSIBLE ELEMENTS AND SPACES IN A BUILDING OR WITHIN
A SITE THAT CAN BE NEGOTIATED BY A PERSON WITH A DISABILITY, USING A WHEELCHAIR, AND THAT IS ALSO SAFE FOR AND
PARKING PARKING IN 12" HIGH 11A-5A (b) GUIDE RAIL
LETTERINGS MIN. 2 % MAX.
USABLE BY PERSONS WITH OTHER DISABILITIES. 8.33 % RAMP WITH HANDRAIL AND CURB OR BARRIER
SECTION B-B 09/12/2022
WITHIN THE LOADING & TYP. MAX. A
RETAINING (b) HANDRAIL SECOND CITY SUBMITTAL
COMMON USE AREAS: UNLOADING ACCESS AISLE TYP. PAVEMENT PAVEMENT DEPRESS ENTIRE
CURB IF 1'-0" 10/26/2022
ARE PRIVATE USE AREAS WITHIN MULTIFAMILY RESIDENTIAL FACILITIES WHERE THE USE OF THESE AREAS IS LIMITED PAINT THE WORDS "NO SYMBOL SYMBOL SIDEWALK AS

30" MAX. RAMP RISE

PARKING" IN 12" HIGH REQUIRED NECESSARY 1'-0" B THIRD CITY SUBMITTAL
EXCLUSIVELY TO OWNERS, RESIDENCE, AND THEIR GUESTS.THE AREAS MAY BE DEFINED AS ROOMS OR SPACES OR ELEMENTS 11A-3C - CURB
INSIDE OR OUTSIDE OF BUILDING. LETTERINGS MIN. DETAIL
SECTION B - B 3
(C.B.C.-CH 2, SECTION 202) ----
11A-2A- DOUBLE PARKING STALLS. 11A-2B- SINGLE PARKING STALLS. 11A-3M - RETURNED

34" TO 38"
BUILDING ACCESSIBILITY: CURB STYLE
4 ----
EACH BUILDING ON A BUILDING SITE SHALL BE CONSIDERED SEPARATELY WHEN DETERMINING THE REQUIREMENTS CONTAINED (SEE ALSO 11B-21)
RETAINING CURB
IN THIS CHAPTER, EXCEPT WHEN CALCULATING THE NUMBER OF UNITS WHICH MUST COMPLY WITH SECTION 1102A.3.1 2% IF NECESSARY 5
DWELLING UNITS WITHIN A SINGLE STRUCTURE SEPARATED BY FIREWALLS DO NOT CONSTITUTE SEPARATE BUILDINGS. MAX. ----
(C.B.C.-1102A.1)
12" MIN. BORDER 4" DRAIN 4" DRAIN 6
RAMP WITH HANDRAIL AT WALL ----
GROOVES AT 3 4" SECTION C - C
MULTISTORY DWELLING UNITS 8.33 %
(ON GROUND FLOOR) IN BUILDINGS WITHOUT ELEVATOR O.C. REFER TO
MAX. PEDESTRIAN SEE BALUSTERS OR PATTERNS 7 ----
70 SQ. INCH. GROOVING
ROUTE GROOVING 11A-3L - CURB SPACED SUCH THAT A 4" DIAMETER SPHERE
AT LEAST 10 % (BUT NOT LESS THAN ONE) OF THE MULTISTORY DWELLINGS IN APARTMENT BUILDINGS WITH 3 OR MORE ACCESSIBILITY DETAIL "11A-3K"
WHEEL DETAIL "3K" SECTION CANNOT PASS THROUGH ANY OPENING
SIGN 8 ----
DWELLING UNITS AND/ OR CONDOMINIUMS WITH 4 OR MORE DWELLING UNITS SHALL COMPLY WITH THE FOLLOWING: STOP
GUARD RAIL

34" TO 38"
42" MIN.
1. THE PRIMARY ENTRY TO THE DWELLING UNIT SHALL BE ON AN ACCESSIBLE ROUTE UNLESS EXEMPTED BY SITE HANDRAIL 9
1'-0" ----
FACE OF DIAGONAL CURB RAMPS.
IMPRACTICALITY TESTS IN SECTION 1150A.

30" MAX. RAMP RISE

CURB IF DIAGONAL (OR CORNER-TYPE) CURB RAMPS HAVE RETURNED CURB OR OTHER WELL-DEFINED EDGES,SUCH EDGES SHALL BE 1'-0"
2. AT LEAST ONE POWDER ROOM OR BATHROOM SHALL BE LOCATED ON THE PRIMARY ENTRY LEVEL, SERVED BY AN PARALLEL TO THE DIRECTION OF PEDESTRIAN FLOW. THE BOTTOM OF DIAGONAL CURB RAMPS SHALL HAVE A 48" MIN. CLEAR ARIZONA # : 27259
ACCESSIBLE ROUTE AND SHALL COMPLY WITH THE PROVISIONS IN DIVISION IV. SPACE (FIG. 11A-3A THROUGH 11A-3M). IF DIAGONAL CURB RAMPS ARE PROVIDED AT MARKED CROSSINGS, THE 48" CLEAR
A A A A SPACE SHALL BE WITHIN THE MARKINGS (FIG. 11A-3A THOUGH 11A-3M). IF DIAGONAL CURB RAMPS HAVE FLARED SIDES, THEY CALIFORNIA # : C15528
STRIPES AT WITHIN THE LOADING & SHALL ALSO HAVE AT LEAST A 24" LONG SEGMENT OF STRAIGHT CURB LOCATED ON EACH SIDE OF THE CURB RAMP AND WITHIN
3. ALL ROOMS OR SPACES LOCATED ON THE PRIMARY ENTRY LEVEL SHALL BE SERVED BY AN ACCESSIBLE ROUTE AND SHALL COLORADO # : 304356
36" ON UNLOADING ACCESS THE MARKED CROSSING. (FIG. 11A-3A THROUGH 11A-3M). (C.B.C.-1112A.4)
COMPLY WITH THE PROVISIONS IN DIVISION IV. ROOMS/SPACES MAY INCLUDE BUT ARE NOT LIMITED TO KITCHENS, POWDER CENTER OREGON # : 5318

.
ROOMS, BATHROOMS, LIVING ROOMS, BEDROOMS OR HALLWAYS. AISLE PAINT THE WORDS
"NO PARKING" IN 12" HIGH 12" MIN. BORDER SLOPE OF CURB RAMPS.
CURB & NEVADA # : 2838
LETTERINGS MIN. CURB & GROOVES AT 3 4" THE SLOPE OF CURB RAMPS SHALL NOT EXCEED 1 UNIT VERT. TO 12 UNITS HORIZ. AND SHALL LIE, GENERALLY, IN A SINGLE
THE MINIMUM NUMBER OF MULTIFAMILY DWELLING UNITS WHICH MUST COMPLY WITH THIS SECTION SHALL BE CALCULATED GUTTER RAMP TEXAS # : 16533
GUTTER O.C. REFER TO SLOPED PLANE. TRANSITIONS FROM RAMPS TO WALKS, GUTTERS, OR STREETS SHALL BE FLUSH AND FREE OF ABRUPT
USING THE TOTAL NUMBER OF ALL MULTISTORY DWELLING UNITS IN BUILDINGS ON A SITE WHICH ARE SUBJECT TO THIS
GROOVING CHANGES. MAX. SLOPES OF ADJOINING GUTTERS, ROAD SURFACE IMMEDIATELY ADJACENT TO THE CURB RAMP, OR LANDING
SECTION. (ANY FRACTION THEREOF SHALL BE ROUNDED TO NEXT HIGHEST WHOLE NUMBER). TYP. PAVEMENT SIDE WALK UTAH # : 7288093-0301

18 LL
ST
DETAIL "11A-3K" ACCESSIBLE ROUTE SHALL NOT EXCEED 1 UNIT VERT. TO 20 UNITS HORIZ. WITHIN 4' OF THE TOP AND BOTTOM OF THE CURB

'-0 D
(C.B.C.-1102A.3.1) SIDE WALK

A
SYMBOL WASHINGTON # : 8895

" EP
RAMP. IF A CURB RAMP IS LOCATED WHERE PEDESTRIANS MUST WALK ACROSS THE RAMP, THEN IT SHALL HAVE FLARED SIDES;

M T
IN H
THE MAX. SLOPE OF THE FLARE SHALL BE 1 UNIT VERT. IN 10 UNITS HORIZ. CURB RAMPS WITH RETURNED CURBS MAY BE USED

RK O
G
.
TOP OF F.F.

N
WHERE PEDESTRIANS WOULD NOT NORMALLY WALK ACROSS THE RAMP. (FIG. 11A-3A THROUGH 11A-3M).

IN
MULTISTORY DWELLING UNITS IN BUILDINGS . ADDRESS:
IN H 11A-3A - CURB 11A-3B-CURB (C.B.C.-1112A.5) OR GROUND
(I.E. TOWN-HOUSE AND CONDOMINIUM-TYPE CONSTRUCTION ) WITH ONE OR MORE ELEVATORS: M IDT RAMP WITH HANDRAIL
" DETAIL DETAIL AND GUARDRAIL 1590 BARTLETT LN
-0 W

PA

1548, 1554, 1560, 1566, 1572, 1578, 1584, & 1590 Bartlett
FOR MULTISTORY DWELLING UNITS IN BUILDINGS WITH ELEVATORS, THE STORY OF THE UNIT THAT IS SERVED BY THE BUILDING 9' LL LEVEL LANDING. SACRAMENTO, CA 95815
A 5'-0" MIN. AT TYP.
ELEVATOR IS CONSIDERED A GROUND FLOOR AND PRIMARY ENTRY FLOOR TO THE UNIT AND THE PRIMARY ENTRY FLOOR TO ST ACCESSIBLE A LEVEL LANDING 48" DEEP SHALL BE PROVIDED AT THE UPPER END OF EACH CURB RAMP OVER ITS FULL WIDTH TO PERMIT
PROVIDE GUARD RAILS IF RAMP / LANDING IS MORE

.
THE UNIT & SHALL COMPLY WITH THE FOLLOWING: DIMENSION TO SAFE EGRESS FROM THE RAMP SURFACE, OR THE SLOPE OF THE FANNED SIDES OF THE CURB RAMP, SHALL NOT EXCEED 1
PARKING STALL 8'-0" THAN 30" ABOVE ADJACENT FLOOR OR GROUND
CENTERLINE OF UNIT VERT. TO 12 UNITS HORIZ. (C.B.C.-1112A.6)
MIN. AT VAN
1. AT LEAST ONE POWDER ROOM OR BATHROOM SHALL BE LOCATED ON THE PRIMARY ENTRY LEVEL. STRIPE TYPICAL ACCESSIBLE NOTES:
PROVIDE PER THE C.B.C. FINISH.
PARKING STALL MAXIMUM SLOPE OF RAMPS ON AN ACCESSIBLE ROUTE SHALL BE NO GREATER THAN 1:12
2016, SECTION 1109A.8.8 THE SURFACE OF EACH CURB RAMP AND ITS FLARED SIDES SHALL BE STABLE, FIRM, AND SLIP-RESISTANT AND SHALL BE OF
2. AT LEAST ONE KITCHEN SHALL BE LOCATED ON THE PRIMARY LEVEL. CROSS SLOPE OF RAMP SURFACES SHALL NOT EXCEED 1/4" PER FOOT.
REQUIREMENTS (TYPICAL) BACK OF CONTRASTING FINISH FROM THAT OF THE ADJACENT SIDEWALK. (C.B.C.-1112A.7) IF RAMP SLOPE LESS THAN 1:20 NO HANDRAIL NEEDED.
3. ALL ROOMS OR SPACES LOCATED ON THE PRIMARY ENTRY LEVEL SHALL BE SERVED BY AN ACCESSIBLE ROUTE AND SHALL SIDEWALK
11A-2C - DIAGONAL
COMPLY WITH DIVISION IV. PARKING STALLS SEE GROOVING BORDER.
(C.B.C.-1102A.3.2) DETAIL "11A-3K" ALL CURB RAMPS SHALL HAVE A GROOVED BORDER 12" WIDE AT THE LEVEL SURFACE OF THE SIDEWALK ALONG THE TOP AND TO SUIT
EACH SIDE APPROXIMATELY 3/4" ON CENTER. ALL CURB RAMPS CONSTRUCTED BETWEEN THE FACE OF THE CURB AND THE GUIDE RAIL
DESIGN

CROSSWALK
4" MIN. .
3. EACH SPACE SHALL BE DESIGNATED "VAN ACCESSIBLE" AS REQUIRED BY SECTION 1109A.8.8. STREET SHALL HAVE A GROOVED BORDER AT THE LEVEL SURFACE OF THE SIDEWALK. (FIG. 11A-3A THROUGH 11A-3K) CENTERED @
TEMPORARY RESTRICTIONS: HIGH
A A (C.B.C.-1112A.8) <4" HIGH
DURING PERIODS OF PARTIAL OR RESTRICTED USE OF A BUILDING OR FACILITY, THE ENTRANCES USED FOR PRIMARY ACCESS
4. ALL VAN ACCESSIBLE SPACES MAY BE GROUPED ON ONE LEVEL OF A MULTILEVEL PARKING FACILITY.

MIN.
48"
SHALL BE ACCESSIBLE TO AND USABLE BY PERSONS WITH DISABILITIES. (C.B.C.-1102A.4) A

D E V E L O P M E N T
.

.
MIN.
5. THE LOADING & UNLOADING ACCESS AISLE SHALL BE MARKED BY A BORDER PAINTED BLUE. WITHIN THE BLUE BORDER, WALKS & SIDEWALKS ON AN ACCESSIBLE ROUTE

MAX. 48"
GROUND FLOORS ABOVE GRADE: HATCHED LINES A MAXIMUM OF 36" ON CENTER SHALL BE PAINTED A COLOR CONTRASTING WITH THE PARKING SURFACE, (C.B.C.-1113A)
WHERE THE FIRST FLOOR CONTAINING DWELLING UNITS IN A BUILDING IS ABOVE GRADE, ALL UNITS ON THAT FLOOR SHALL BE PREFERABLY BLUE OR WHITE. THE WORDS "NO PARKING" SHALL BE PAINTED ON THE GROUND WITHIN EACH 5-FOOT WIDE

2%
SERVED BY AN ACCESSIBLE ROUTE. THIS FLOOR WILL BE CONSIDERED A GROUND FLOOR AND ALL DWELLING UNITS ARE LOADING & UNLOADING ACCESS AISLE. THIS NOTICE SHALL BE PAINTED IN WHITE LETTERS NO LESS THAN 12 INCHES HIGH 11A-5A (b) GUIDE RAIL DETAIL 11A-5A (c) GUIDE RAIL DETAIL

8.33 % MAX.
48" WIDTH AND CONTINUOUS SURFACE.
CONSIDERED COVERED MULTIFAMILY DWELLING UNITS. AND LOCATED SO THAT IT IS VISIBLE FROM THE ADJACENT VEHICULAR WAY. (FIG. 11A-2A, 2B & 2C)
MIN. WALKS AND SIDEWALKS SHALL HAVE A CONTINUOUS COMMON SURFACE, NOT INTERRUPTED BY STEPS OR BY ABRUPT
EXCEPTION: CARRIAGE UNITS AS DEFINED IN CHAPTER 2 & REGULATED ONLY BY DEPARTMENT OF HOUSING & COMMUNITY (C.B.C.-1109A.8.6) 10 % MAX.
CHANGES IN LEVEL EXCEEDING 1/2". (C.B.C.-1113A.1)
DEVELOPMENT AS REFERENCED IN SECTION 1.8.2.1.2. C.B.C.-1104A.2) AT CURB
HANDRAIL REQUIRED WIDTH HANDRAIL REQUIRED WIDTH
ADJACENT PARKING. FULL CURB WIDTH OF THE RAMP OF THE RAMP
SITE & BUILDING CHARACTERISTICS: PARKING SPACES ADJACENT TO ACCESSIBLE PARKING SPACES SHALL NOT BE CONSIDERED AS LOADING & UNLOADING ACCESS WALKS AND SIDEWALKS SHALL BE 48" MIN. IN WIDTH, EXCEPT THAT WALKS SERVING AN INDIVIDUAL DWELLING UNIT IN COVERED CURB, RAIL, WALL
HEIGHT
AISLES. (C.B.C.-1109A.8.7) MULTIFAMILY BUILDINGS MAY BE REDUCED TO 36" IN CLEAR WIDTH EXCEPT AT DOORS. (C.B.C.-1113A.1.1) OR BARRIER SHALL HANDRAIL
10 % MAX.
GENERAL.

GATEWAY
AT CURB BE PROVIDED THAT & CURB
A

VILLAGE-PHASE 2
COVERED MULTIFAMILY DWELLINGS WITH ELEVATORS SHALL BE DESIGNED & CONSTRUCTED TO PROVIDE AT LEAST ONE SURFACE CROSS SLOPES. PREVENTS THE
PARKING SIGNAGE.
ACCESSIBLE ENTRANCE ON AN ACCESSIBLE ROUTE, REGARDLESS OF TERRAIN OR UNUSUAL CHARACTERISTICS OF THE SITE. SURFACE CROSS SLOPES SHALL NOT EXCEED 1 UNIT VERTICAL IN 48 UNITS HORIZONTAL. (C.B.C.-1113A.1.2) PASSAGE OF A
CROSSWALK

34" TO 38"

34" TO 38"
EACH ACCESSIBLE PARKING SPACE RESERVED FOR PERSONS WITH DISABILITIES SHALL BE IDENTIFIED BY A REFLECTIVE SIGN
COVERED MULTIFAMILY DWELLINGS WITHOUT ELEVATORS SHALL BE DESIGNED & CONSTRUCTED TO PROVIDE AT LEAST ONE 3"±1" HIGH

34" TO 38"
4" DIAMETER SPHERE,

4" MAX.
CONSISTING OF THE "INTERNATIONAL SYMBOL OF ACCESSIBILITY" COMPLYING WITH SECTION 1143A.8. THE SIGN SHALL NOT BE
ACCESSIBLE ENTRANCE ON AN ACCESSIBLE ROUTE, UNLESS TERRAIN OR UNUSUAL CHARACTERISTICS OF THE SITE PREVENT WALKS WITH CONTINUOUS GRADIENTS. WHERE ANY PORTION WHEEL
SMALLER THAN 70 SQUARE INCHES AREA, AND SHALL BE POSTED 60 INCHES MINIMUM ABOVE THE FINISH FLOOR OR GROUND
AN ACCESSIBLE ROUTE BASE ON THE CONDITIONS LISTED BELOW: ALL WALKS ON AN ACCESSIBLE ROUTE WITH CONTINUOUS GRADIENTS SHALL HAVE LEVEL AREAS AT LEAST 60" IN LENGTH AT OF THE SPHERE IS 1'-0" MIN., TYP. GUIDE
SURFACE, MEASURED TO THE BOTTOM OF THE SIGN. SIGNS LOCATED ON ACCESSIBLE ROUTES SHALL BE POSTED AT A 4" MIN. HIGH
INTERVALS OF AT LEAST EVERY 400 FEET. (C.B.C.-1113A.2)

APARTMENTS
MINIMUM HEIGHT OF 80 INCHES ABOVE THE FINISH FLOOR OR GROUND SURFACE OF THE ACCESSIBLE ROUTE MEASURED TO 11A-3D - CURB WITHIN 4" OF THE
1. AN ACCESSIBLE ENTRANCE IS REQUIRED WHEN THERE IS AN ELEVATOR CONNECTING THE PARKING AREA WITH THE FLOOR OR GROUND CONTINUOUS
THE BOTTOM OF THE SIGN. DETAIL GUIDE CURB
DWELLING UNITS ON A GROUND FLOOR. (IN THIS CASE, THOSE DWELLING UNITS ON THE GROUND FLOOR SERVED BY AN 5% GRADIENT. SURFACE 48" MIN. CLR.

SACRAMENTO, CALIFORNIA
ELEVATOR, AND AT LEAST ONE OF EACH TYPE OF PUBLIC AND COMMON-USE AREAS, WOULD BE SUBJECT TO THESE WHEN THE SLOPE IN THE DIRECTION OF TRAVEL OF ANY WALK ON AN ACCESSIBLE ROUTE EXCEEDS 1 UNIT VERT. IN 20 UNITS EDGE PROTECTION -
SIGNS IDENTIFYING ACCESSIBLE PARKING SPACES SHALL BE VISIBLE FROM EACH PARKING SPACE THEY SERVE, AND SHALL BE
REQUIREMENTS) HORIZ, IT SHALL COMPLY WITH THE RAMP PROVISIONS OF SECTION 1114A. (C.B.C.-1113A.3 ) EDGE PROTECTION - EXTENDED SURFACE 11A-5A (c) WHEEL GUIDE
PERMANENTLY POSTED IMMEDIATELY ADJACENT TO THE PARKING SPACE OR WITHIN THE PROJECTED PARKING SPACE WIDTH IF RETAINING CURB A
AT THE HEAD END OF THE PARKING SPACE. SIGNS MAY ALSO BE PERMANENTLY POSTED ON A WALL AT THE INTERIOR END OF OR CURB OR BARRIER
2. WHEN ELEVATOR PROVIDED AS A MEANS OF ACCESS TO DWELLING UNITS OTHER THAN DWELLING UNITS ON A GROUND NECESSARY AT BACK DETAIL CAN BE USED IF LENGHT
B LEVEL AREAS.
THE PARKING SPACE. OF SIDEWALK OF THE RAMP LESS THAN 10'-0"
FLOOR, THE BUILDING IS AN ELEVATOR BUILDING. ALL DWELLING UNITS BECOME MULTIFAMILY DWELLING IN THAT BUILDING. WALKS ON AN ACCESSIBLE ROUTE SHALL BE PROVIDED WITH A LEVEL AREA AT EACH SIDE OF A DOOR OR GATE. LEVEL AREAS
THE ELEVATOR IN THAT BUILDING MUST PROVIDE ACCESSIBILITY TO ALL DWELLING UNITS IN THE BUILDING, REGARDLESS SHALL COMPLY WITH THE APPLICABLE REQUIREMENTS FOR MANEUVERING CLEARANCES IN SECTION 1126A.3.

MAX.

MAX.
VAN ACCESSIBLE SPACES SHALL COMPLY WITH SECTION 1109A.8.6 AND SHALL HAVE AN ADDITIONAL SIGN OR ADDITIONAL RETAINING CURB 11A-5A - RAMP &
OF THE SLOP OF THE NATURAL TERRAIN.

2%

2%
(C.B.C.-1113A.4 )
LANGUAGE STATING "VAN ACCESSIBLE" BELOW THE SYMBOL OF ACCESSIBILITY. SIDEWALK

MIN.
IF NECESSARY AT SEE GROOVING
C

48"
NOTE: WHERE A BUILDING ELEVATOR IS PROVIDED ONLY AS MEANS OF CREATING AN ACCESSIBLE ROUTE TO COVERED EDGE DETAIL "3K" GRATINGS. 1 14" MIN.
AN ADDITIONAL SIGN SHALL ALSO BE POSTED IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO OFF-STREET PARKING OF SIDEWALK 2 14" 1 14" MIN.
MULTIFAMILY DWELLING UNITS ON A GROUND FLOOR, THE BUILDING IS NOT CONSIDERED TO BE AN ELEVATOR BUILDING, GRID OPENINGS IN GRATINGS SHALL BE LIMITED TO 12" IN THE DIRECTION OF TRAFFIC FLOW. ELONGATED OPENINGS SHALL BE
FACILITIES OR IMMEDIATELY ADJACENT TO & VISIBLE FROM EACH STALL OR SPACE. THE SIGN SHALL NOT BE LESS THAN 17" BY 1
1 2" MIN. MAX. 2" MAX. 1 12" MIN. 1
ONLY DWELLING UNITS LOCATED ON THE GROUND FLOOR SHALL BE REQUIRED TO COMPLY WITH THIS CHAPTER. PLACED SO THAT THE LONG DIMENSION IS PERPENDICULAR TO THE DOMINANT DIRECTION OF TRAFFIC. (C.B.C.-1113A.5) 8" MIN. 1 1 4" MIN.
22" IN SIZE WITH LETTERING NOT LESS THAN 1" IN HEIGHT, AND SHALL CLEARLY AND CONSPICUOUSLY STATE THE FOLLOWING: 48" . . . . RADIUS

THAN 60"

MIN.
8.33 %

18"
8.33 % MIN. SEE 1 1/2" MIN.

MAX.
3. WHEN AN ELEVATED WALKWAY IS PLANNED BETWEEN A BUILDING ENTRANCE & A VEHICULAR OR PEDESTRIAN ARRIVAL FRONT EDGE OF (TYP.) 1 12"

MAX.
"UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOT DISPLAYING DISTINGUISHING PLACARDS OR 10 %

LESS

2%
POINT, AND THE PLANNED WALKWAY HAS A SLOPE NO GREATER THAN 10%, THE FLOOR BEING SERVED BY THE ELEVATED MAX. GROOVING SIDEWALK EXTERIOR RAMPS & LANDINGS ON ACCESSIBLE ROUTES
SPECIAL LICENSE PLATES ISSUED FOR PERSONS WITH DISABILITIES MAY BE TOWED AWAY AT OWNER'S EXPENSE. TOWED DETAIL "3K" MAX. (C.B.C.-1114A) 1 1 4" MIN. . .

PERIMETER
WALKWAY BECOMES A GROUND FLOOR AND ACCESSIBILITY TO ALL DWELLINGS ON THAT GROUND FLOOR IS REQUIRED.

1 12" MIN.
VEHICLES MAY BE RECLAIMED AT ---------------------------------------- OR BY TELEPHONING ----------------". 1 1/2"

.
2" MAX.

4"-6 1 4"
BANK SPACES ARE TO BE FILLED IN WITH APPROPRIATE INFORMATION AS A PERMANENT PART OF THE SIGN. 1
1 2" MAX.
NOTE: SINCE THE PLANNED WALKWAY MEETS THE 10% SLOPE CRITERION, IT IS REQUIRED TO PROVIDE AN ACCESSIBLE WIDTH 2 14" . .
(FIG. 11A-2A, 2B& 2C) (C.B.C.-1109A.8.8.1) MIN.
ROUTE TO THE ENTRANCE, AND THE SLOPE OF THE WALKWAY MUST BE REDUCED TO 1 UNIT VERTICAL IN 12 UNITS

WALL
A IN NO CASE SHALL WIDTH OF RAMPS BE LESS THAN 48 INCHES. MAX. 1 1/2"

.
HORIZONTAL MAX. C OR

D E B A R T O L O
B MIN.

.
(C.B.C.-1106A) 1
HANDRAILS MAY PROJECT INTO THE REQUIRED CLEAR WIDTH OF THE RAMP AT EACH SIDE 3 2 INCHES MAXIMUM AT THE

.
48"
HANDRAIL HEIGHT. CURBS, WHEEL GUIDES AND/OR APPURTENANCES SHALL NOT PROJECT INTO THE REQUIRED CLEAR WIDTH
MIN. TO SUIT
EXTERIOR ACCESSIBLE ROUTES: OF RAMPS. . DESIGN

.
(C.B.C.-1110A)
EXTERIOR FACILITIES - PARKING EXCEPTION: THE CLEAR WIDTH OF RAMPS SERVING ACCESSIBLE ENTRANCES TO COVERED MULTIFAMILY DWELLINGS WITH AN
11A-3F - CURB 11A-3E - CURB 3" MAX.
(C.B.C.-1109A) OCCUPANT LOAD OF 10 OR LESS MAY BE 36 INCHES MINIMUM BETWEEN HANDRAILS. (C.B.C.-1114A.1)
EXTERIOR ACCESSIBLE ROUTE. DETAIL DETAIL
(a) HANDRAILS (b) HANDRAILS (c) HANDRAILS (d) HANDRAILS
REQUIRED ACCESSIBLE PARKING SPACES. WHEN A BUILDING OR PORTION OF A BUILDING IS REQUIRED TO BE ACCESSIBLE OR ADAPTABLE, AN ACCESSIBLE ROUTE SHALL W/CIRCULAR CROSS W/NON-CIRCULAR LOCATED IN A W/EQUIVALENT
SLOPE
ACCESSIBLE PARKING SPACES SHALL BE PROVIDED AT THE MINIMUM RATE OF 2 % OF THE COVERED MULTIFAMILY DWELLING BE PROVIDED TO ALL PORTIONS OF THE BUILDING, ACCESSIBLE BUILDING ENTRANCES & BETWEEN THE BUILDING & THE PUBLIC SECTION CROSS SECTION RECESS GRIPPING SURFACES
THE MAX. SLOPE OF RAMPS ON AN ACCESSIBLE ROUTE SHALL BE NO GREATER THAN 1 UNIT VERT. IN 12 UNITS HORIZ.
UNITS. AT LEAST ONE SPACE OF EACH TYPE OF PARKING FACILITY SHALL BE MADE ACCESSIBLE EVEN IF THE TOTAL NUMBER WAY. THE ACCESSIBLE ROUTE SHALL BE THE MOST PRACTICAL DIRECT ROUTE & TO THE MAX. EXTENT FEASIBLE, COINCIDE
TRANSITIONS FROM RAMPS TO WALKS, GUTTERS OR STREETS SHALL BE FLUSH AND FREE OF ABRUPT CHANGES.
EXCEEDS 2 %. (C.B.C.-1109A.3) WITH THE ROUTE FOR THE GENERAL PUBLIC AND BUILDING RESIDENTS. 11A-6B - STAIR

ARDEN
EXCEPTION: RAMPS SERVING DECKS, PATIOS OR BALCONIES AS SPECIFIED IN SECTION 1132A.4. (C.B.C.-1114A.2) HANDRAILS
ASSIGNED ACCESSIBLE PARKING SPACES. EXTERIOR ACCESSIBLE ROUTES SHALL BE PROVIDED AS FOLLOWS:
WHEN ASSIGNED PARKING SPACES ARE PROVIDED FOR A RESIDENT OR A GROUP OF RESIDENTS, AT LEAST 2% OF THE CROSSWALK CROSS SLOPE.
ASSIGNED PARKING SPACES SERVING COVERED MULTIFAMILY DWELLING UNITS SHALL BE ACCESSIBLE IN EACH TYPE OF 1. AT LEAST ONE ACCESSIBLE ROUTE WITHIN THE BOUNDARY OF THE SITE SHALL BE PROVIDED FROM PUBLIC
SEE GROOVING THE CROSS SLOPE OF RAMP SURFACES SHALL BE NO GREATER THAN 1 UNIT VERTICAL IN 48 UNITS HORIZONTAL. 60" MIN. WHEN NO DOOR 6
TRANSPORTATION STOPS, ACCESSIBLE PARKING AND ACCESSIBLE PASSENGER LOADING & UNLOADING ZONES, AND PUBLIC
PARKING FACILITY. AT LEAST ONE SPACE OF EACH TYPE OF PARKING FACILITY SHALL BE MADE ACCESSIBLE EVEN IF THE TOTAL DETAIL "11A-3K"
12" MIN. BORDER (C.B.C.-1114A.2.1) SWINGS ONTO LANDING
E
SE E 1 MI 0"
STREETS OR SIDEWALKS TO ACCESSIBLE SIDEWALKS TO THE ACCESSIBLE BUILDING ENTRANCE THEY SERVE. WHERE MORE GROOVES AT T N.
NUMBER EXCEEDS 2%. WHEN ASSIGNED PARKING IS PROVIDED, SIGNAGE AS REQUIRED BY SECTION 1109A.8.8 SHALL NOT BE O
REQUIRED. (C.B.C.-1109A.4) THAN ONE ROUTE OF TRAVEL IS PROVIDED, ALL ROUTED SHALL BE ACCESSIBLE. 3 A N
4 " O.C. LOCATION OF LANDINGS.
M 8"

E
SE E 2
.
4
IN

LANDINGS SHALL BE PROVIDED AT THE TOP & BOTTOM OF EACH RAMP. INTERMEDIATE LANDINGS SHALL BE PROVIDED AT T
UNASSIGNED & VISITOR PARKING SPACES. 2. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE BUILDINGS, FACILITIES, ELEMENTS & SPACES THAT ARE NO
48" INTERVALS NOT EXCEEDING 30" OF VERTICAL RISE & AT EACH CHANGE OF DIRECTION. LANDING ARE NOT CONSIDERED IN
WHEN PARKING IS PROVIDED FOR COVERED MULTIFAMILY DWELLINGS AND IS NOT ASSIGNED TO A RESIDENT OR A GROUP OF ON THE SAME SITE. ACCESSIBLE ROUTES SHALL BE PROVIDED BETWEEN ACCESSIBLE BUILDINGS & ACCESSIBLE SITE A "
MIN. DETERMINING THE MAX. HORIZ. DISTANCE OF EACH RAMP. (C.B.C.-1114A.4.1) 60 .
FACILITIES WHEN MORE THAN ONE BUILDING OR FACILITY IS LOCATED ON A SITE. N
MI

MIN.
RESIDENTS AT LEAST 5% OF THE PARKING SPACES SHALL BE ACCESSIBLE AND PROVIDE ACCESS TO GRADE-LEVEL ENTRANCES

48"
OF COVERED MULTIFAMILY DWELLINGS & FACILITIES (E.G., SWIMMING POOLS, CLUB HOUSES, RECREATION AREAS, & LAUNDRY SIZE OF TOP LANDINGS.

MAX.
3. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE BUILDING OR FACILITY ENTRANCES WITH ALL E
ROOMS) THAT SERVE COVERED MULTIFAMILY DWELLINGS. (C.B.C.-1109A.5) 10 % MAX. SIDES SE E 2

2%
TOP LANDINGS SHALL NOT BE LESS THAN 60" WIDE & 60" MIN. LENGTH IN THE DIRECTION OF THE RAMP RUN. (C.B.C.-1114A.4.2)
MIN.

T
48"

ACCESSIBLE SPACES, ELEMENTS & COVERED MULTIFAMILY DWELLING UNITS. AT CURB O "
30 . TOP LEVEL
SEE GROOVING N X
MA PLATFORM
SIZE OF BOTTOM AND INTERMEDIATE LANDINGS. "

8.33 %
DETAIL "11A-3K" 72 .
M 8"

4. AN ACCESSIBLE ROUTE SHALL CONNECT AT LEAST ONE ACCESSIBLE ENTRANCE OF EACH COVERED MULTIFAMILY
.

MAX.
IN
4

10 % THE MIN. WIDTH OF BOTTOM & INTERMEDIATE LANDINGS SHALL NOT BE LESS THAN THE WIDTH OF THE RAMP. (C.B.C.-1114A.4.3) N
DWELLING UNIT WITH EXTERIOR SPACES AND FACILITIES THAT SERVE THE DWELLING UNIT. FRONT EDGE OF MI
LOCATION OF ACCESSIBLE PARKING SPACES. MAX. INTERMIDIATE
1. ACCESSIBLE PARKING SPACES SHALL BE LOCATED ON THE SHORTEST POSSIBLE ACCESS ROUT TO AN ACCESSIBLE SIDEWALK ENCROACHMENT OF DOORS. 60" MIN. WHEN NO DOOR 60
5. WHERE ELEVATORS ARE PROVIDED FOR VERTICAL ACCESS, ALL ELEVATORS SHALL BE ACCESSIBLE. SEE SECTION 1124A. LEVEL PLATFORM E MI "
BUILDING ENTRANCE. ALL VAN ACCESSIBLE SPACES MAY BE GROUPED ON ONE LEVEL OF A PARKING FACILITY. DOORS IN ANY POSITION SHALL NOT REDUCE THE MIN. DIMENSION OF THE LANDING TO LESS THAN 42" & SHALL NOT REDUCE SWINGS ONTO LANDING SE E 1 N.
NOTE: IF THE SLOPE OF THE FINISH GRADE BETWEEN COVERED MULTIFAMILY DWELLINGS AND SITE ARRIVAL POINTS, OT
THE REQUIRED WIDTH BY MORE THAN 3" WHEN FULLY OPEN. (11A-6D). (C.B.C.-1114A.4.4) N
PUBLIC USE OR COMMON USE FACILITIES (INCLUDING PARKING) EXCEEDS 1 UNIT VERT. IN 12 UNITS HORIZ., OR WHERE OTHER 4 0"
2. WHEN PARKING FACILITIES ARE LOCATED ADJACENT TO A BUILDING WITH MULTIPLE ACCESSIBLE ENTRANCES, M 8" A A E
PHYSICAL BARRIERS (NATURAL OR ARTIFICIAL) OR LEGAL RESTRICTIONS, ALL OF WHICH ARE OUTSIDE THE CONTROL OF THE IN 2% BOTTOM SE E 2
ACCESSIBLE PARKING SPACES SHALL BE DISPERSED AND LOCATED NEAR THE ACCESSIBLE BUILDING ENTRANCES. . CHANGE OF DIRECTION. O T
OWNER, PREVENT THE INSTALLATION OF AN ACCESSIBLE ROUTE, AN ACCEPTABLE ALTERNATIVE IS TO PROVIDE ACCESS BY A MAX. LEVEL N
INTERMEDIATE LANDINGS AT A CHANGE OF DIRECTION SHALL BE SIZED TO PROVIDE 60" TURNING SPACE COMPLYING WITH A
VEHICULAR ROUTE, PROVIDED : 48" 0" OR RE S PLATFORM "
60 .
3. WHEN PRACTICAL, THE ACCESSIBLE ROUTE SHALL NOT CROSS LANES FOR VEHICULAR TRAFFIC. WHEN CROSSING SECTION 1138A.1.3. INTERMEDIATE LANDINGS AT A CHANGE OF DIRECTION IN EXCESS OF 30° SHALL HAVE A LENGTH IN THE Q'D N
VEHICLE TRAFFIC LANES IS NECESSARY, THE ACCESSIBLE ROUTES SHALL BE DESIGNATED & MARKED AS A MIN. GREATER DIRECTION OF RAMP RUN OF NOT LESS THAN 72". (FIG. 11A-6C & 6D). (C.B.C.-1114A.4.6) MI
1. THERE IS ACCESSIBLE PARKING ON AN ACCESSIBLE ROUTE FOR AT LEAST 2% OF THE DWELLING UNITS, & 11A-6C (a) STRAIGHT RAMP RUN
CROSSWALK. E
2. NECESSARY SITE PROVISIONS SUCH AS PARKING SPACES & CURB RAMPS ARE PROVIDED AT THE PUBLIC USE OR SE E 2 TOP LEVEL
O T "
60 . PLATFORM
COMMON USE FACILITY. NOTE 1: WHEN DOOR N MA
X
4. PARKING FACILITIES THAT DO NOT SERVE A PARTICULAR BUILDING SHALL HAVE ACCESSIBLE PARKING SPACES 11A-3H - CURB 11A-3G - CURB RAMP HANDRAILS. (C.B.C.-1114A.6)
(C.B.C.-1110A.1) SWINGS ONTO "
LOCATED ON THE SHORTEST POSSIBLE ACCESSIBLE ROUTE TO AN ACCESSIBLE PEDESTRIAN ENTRANCE OF THE DETAIL DETAIL 72 .
LANDING, 42" MIN. PLUS N
PARKING FACILITY. WHERE REQUIRED: HANDRAILS SHALL BE PROVIDED AT EACH SIDE OF RAMPS WHEN THE SLOPE EXCEEDS 1 UNIT VERT. MI INTERMIDIATE
IN 20 UNITS HORIZ. DOOR WIDTH
LEVEL PLATFORM
5. ACCESSIBLE PARKING SPACES SHALL BE LOCATED SO THAT PERSONS WITH DISABILITIES ARE NOT COMPELLED TO PER ANSI
WHEEL OR WALK BEHIND PARKED CARS OTHER THAN THEIR OWN. EXCEPTIONS: NOTE 2: MAX. HORIZ. A117.1-2009
SIGNS. "
30 .
A A 1. CURB RAMPS. DISTANCE OF EACH 405.7 X INTERMIDIATE MILESTONE:
AT EVERY PRIMARY PUBLIC ENTRANCE & AT EVERY MAJOR JUNCTION WHERE THE ACCESSIBLE ROUTE DIVERGES FROM THE OR
SEE OR MA
EXCEPTION: WHEN THE ENFORCEMENT AGENCY DETERMINES THAT COMPLIANCE WITH THIS SECTION OR PROVIDING 2. RAMPS THAT SERVE AN INDIVIDUAL DWELLING UNIT MAY HAVE ONE HANDRAIL, EXCEPT THAT RAMPS OPEN ON ONE RAMP & RUN VARY TURNING PLATFORM THIRD CITY SUBMITTAL
CIRCULATION PATH ALONG OR LEADING TO AN ACCESSIBLE ROUTE, ENTRANCE OR FACILITY, THERE SHALL BE A SIGN B GROOVING B
EQUIVALENT FACILITATION WOULD CREATE AN UNREASONABLE HARDSHIP, PARKING SPACES MAY BE PROVIDED WHICH DETAIL OR BOTH SIDES SHALL HAVE HANDRAILS PROVIDED ON THE OPEN SIDE OR SIDES.
DISPLAYING THE "INTERNATIONAL SYMBOL OF ACCESSIBILITY." SIGNS SHALL INDICATE THE DIRECTION TO ACCESSIBLE 60
WOULD REQUIRE A PERSON WITH PHYSICAL DISABILITIES TO WHEEL OR WALK BEHIND OTHER THAN ACCESSIBLE PARKING 3. RAMPS AT EXTERIOR DOOR LANDING WITH LESS THAN 6" RISE OR LESS THAN 72" IN LENGTH. NOTE 3: THE MAXIMUM MI "
MAX.

BUILDING ENTRANCES & FACILITIES & SHALL COMPLY WITH THE REQUIREMENTS FOUND IN SECTION 1143A. (C.B.C.-1110A.2) "11A-3K" BOTTOM LEVEL

COM-2213627 to COM-2213634
2%

SPACES. FRONT SLOPE OF A RAMP N.

PLATFORM
MIN.

SEE GROOVING
MIN.

(C.B.C.-1109A.7) EDGE OF A A C A . (C.B.C.-1114A.6.2)

48"

48"

FLOOR AND GROUND SURFACES THAT SERVES ANY EXIT DRAWN: MH, NM
DETAIL "11A-3K"
MAX.

SIDEWALK WAY. PROVIDES

2%

FLOOR AND GROUND SURFACES SHALL BE STABLE, FIRM, AND SLIP RESISTANT. IF CARPET OR CARPET TILE IS USED IN A
ARRANGEMENT OF PARKING SPACES. A A THE TOP OF HANDRAILS SHALL BE 34" TO 38" ABOVE THE RAMP SURFACE. ACCESS FOR PERSONS 0"
CHECKED:
COMMON USE AREA OR PUBLIC USE AREA ON A GROUND OR FLOOR SURFACE, IT SHALL HAVE FIRM BACKING OR NO BACKING. JM
PARKING SPACES SHALL BE ARRANGED TO COMPLY WITH THE FOLLOWING: WITH DISABILITIES, OR 72
CARPET OR CARPET TILE SHALL HAVE A LEVEL LOOP, TEXTURED LOOP, LEVEL CUT PILE, OR LEVEL CUT/UNCUT PILE TEXTURE. 10 % MAX.
8.33 %

48" A A C HANDRAILS ON ALL RAMPS SHALL BE CONTINUOUS WITHIN THE THE FULL LENGTH OF EACH RAMP IS IN THE PATH OF MI " Monday, October 24, 2022
AS 'D PLOT DATE:
MAX.

THE MAXIMUM PILE HEIGHT SHALL BE 12 INCH. EXPOSED EDGES OF CARPET SHALL BE FASTENED TO FLOOR SURFACES AD HAVE N.
8.33 %

SIDE MIN. RUN. INSIDE HANDRAILS ON SWITCHBACK OR DOGLEG RAMPS SHALL BE CONTINUOUS BETWEEN RAMP RUNS.
1. IN EACH PARKING AREA, A BUMPER OR CURB SHALL BE PROVIDED & LOCATED TO PREVENT ENCROACHMENT OF CARS PLANTING PLANTING 11A-6C (b) RAMP WITH TURNING Q
MAX.

TRAVEL SHAL BE 1'

OVER THE REQUIRED WIDTH OF WALKWAYS.
TRIM ALONG THE ENTIRE LENGTH OF THE EXPOSED EDGE. CARPET EDGE TRIM SHALL COMPLY WITH SECTION 1111A SLOPE
AREA AREA RE
REQUIREMENTS FOR CHANGES IN LEVEL. 48" FRONT EDGE OF RISE IN 12' OF PLATFORM
10 %
2. RAMPS, INCLUDING CURB RAMPS, SHALL NOT ENCROACH INTO ANY ACCESSIBLE PARKING SPACE OR THE ADJACENT HANDRAIL EXTENSIONS: HANDRAILS SHALL EXTEND 12" MINIMUM HORIZ. ABOVE LANDINGS, BEYOND THE TOP AND HORIZONTAL RUN. E D A RC
ER
(C.B.C.-1110A.3) MIN. MAX. SIDEWALK
LOADING & UNLOADING ACCESS AISLE. BOTTOM OF THE RAMP RUNS. EXTENSIONS SHALL RETURN TO THE WALL, GUARD, OR THE WALKING SURFACE, OR SHALL
R Z JA

H
ST
(C.B.C.-1109A.8.2) BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT RAMP RUN. HANDRAIL EXTENSIONS SHALL BE IN THE SAME
MA
NOTE 4: THE CROSS
B

IT E
CHANGES IN LEVEL ON ACCESSIBLE ROUTES: DIRECTION AS THE RAMP RUNS. (FIG. 11A-5A) 11A-6C - RAMP DIMENSIONS

R EG I
A A SLOPE OF RAMP

FA RA
(REFER TO SHEETS A9-1.4 & A9-1.5 FOR DOOR THRESHOLD REQUIREMENTS AT COVERED MULTIFAMILY DWELLING UNITS)

BA
SLOPE OF ACCESSIBLE PARKING SPACES. OR OR
SURFACES SHALL BE

CT
(C.B.C.-1111A) B B
SURFACE SLOPES OF ACCESSIBLE PARKING SPACES & ACCESS AISLES SHALL BE THE MINIMUM POSSIBLE & SHALL NOT HANDRAIL PROJECTIONS: HANDRAILS PROJECTING FROM A WALL SHALL HAVE A SPACE OF 1 12" BETWEEN THE WALL & NO GREATER THAN

RI
No. C 15528

THIRD CITY SUBMITTAL 10/26/2022

EXCEED 1/4" PER FOOT IN ANY DIRECTION. (C.B.C.-1109A.8.3) THE HANDRAIL. HANDRAILS SHALL NOT REDUCE THE REQUIRED MIN. CLEAR WIDTH OF RAMPS. HANDRAILS MAY BE 1:48.
CHANGES IN LEVEL NOT EXCEEDING 1/2": LOCATED IN A RECESS IF THE RECESS IS A MAX. OF 3" DEEP & EXTENDS AT LEAST 18" ABOVE THE TOP OF THE RAIL
ABRUPT CHANGES IN LEVEL ALONG ANY ACCESSIBLE ROUTE SHALL NOT EXCEED 1/2". WHEN CHANGE IN LEVEL DO OCCUR, 60" MIN. WHEN NO DOOR
E 60
MI "
Exp. 03/31/23
________
THEY SHALL BE BEVELED WITH THE SLOPE NO GREATER THAN ONE UNIT VERT. IN TWO UNITS HORIZ. CHANGES IN LEVEL NOT
11A-3J - CURB 11A-3I - CURB SWINGS ONTO LANDING SE E 1 N.
ACCESSIBLE SINGLE PARKING SPACE. DETAIL DETAIL HANDRAIL GRIPPING SURFACES: HANDRAIL GRIPPING SURFACES SHALL BE CONTINUOUS ALONG THEIR LENGTH, AND O T
N TOP LEVEL TA

IA
EXCEEDING 1/4" MAY BE VERTICAL. (C.B.C.-1111A.1) N

S
WHERE ACCESSIBLE SINGLE SPACES ARE PROVIDED, THEY SHALL BE CONSTRUCTED IN ACCORDANCE WITH THE FOLLOWING: SHALL NOT BE OBSTRUCTED ALONG THEIR TOPS OR SIDES. THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL TE
O F CA L I F O R
PLATFORM 24" MIN.
NOT BE OBSTRUCTED FOR MORE THAN 20% OF THEIR LENGTH. WHEN PROVIDED, HORIZONTAL PROJECTIONS SHALL E EXTERIOR & 18"
1. SINGLE SPACES SHALL BE 14' WIDE & LINED TO PROVIDE A 9' WIDE PARKING AREA & 5' WIDE LOADING & UNLOADING ACCESS CHANGES GREATER THAN 1/2":
OCCUR 1 12" MIN. BELOW THE BOTTOM OF THE HANDRAIL GRIPPING SURFACE. THE DISTANCE BETWEEN HORIZONTAL SE E 2 MIN. INTERIOR
CHANGES IN LEVEL GREATER THAN 1/2" SHALL BE MADE BY MEANS OF A SLOPED SURFACE NOT GREATER THAN ONE UNIT VERT. O T
AISLE . ACCESS AISLE SHALL BE PERMITTED TO BE LOCATED ON EITHER SIDE OF THE VEHICLE, & SHALL EXTEND THE FULL APPROX. 3 4" EXCEPT PROJECTIONS AND THE BOTTOM OF THE GRIPPING SURFACE SHALL BE PERMITTED TO BE REDUCED BY 18" FOR EACH 12" N BEYOND THE
REQUIRED LENGTH OF PARKING SPACE THEY SERVE. (FIG. 11A-2A) IN 20 UNITS HORIZ., OR A CURB RAMP, RAMP, ELEVATOR OR SPECIAL ACCESS LIFT. STAIRS SHALL NOT BE PART OF AN APPROX. 1 12" ON SLOPING OF ADDITIONAL HANDRAIL PERIMETER DIMENSION THAT EXCEEDS 4". . STRIKE EDGE
ACCESSIBLE ROUTE. WHEN STAIRS ARE LOCATED ALONG OR ADJACENT TO AN ACCESSIBLE ROUTE THEY SHALL COMPLY WITH PORTION OF RAMP " OF A GATE OR PROJECT NO. 2021-051
2. WHEN MORE THAN ONE SPACE IS PROVIDED, TWO 9' WIDE PARKING SPACES MAY BE LINED ON EACH SIDE OF A 5' WIDE SECTION 1115A FOR EXTERIOR STAIRWAYS. (C.B.C.-1111A.2) EXCEPTION: WHERE HANDRAILS ARE PROVIDED ALONG WALKING SURFACES WITH SLOPES NOT STEEPER THAN 1 UNIT 72 . 60"
N DOOR ON THE
LOADING & UNLOADING ACCESS AISLE (FIG. 11A-2A, 11A-2B, & 11A-2C) This set of plans and specifications must be VERTICAL IN 20 UNITS HORIZONTAL, THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL BE PERMITTED TO BE MI MIN.
0" SIDE TOWARD PROJECT PHASE .
1/4" kept on the job at all times and it is unlawful to OBSTRUCTED ALONG THEIR ENTIRE LENGTH WHERE THEY ARE INTEGRAL TO CRASH RAILS OR BUMPER GUARDS. WHICH IT
3. THE MINIMUM LENGTH OF EACH PARKING SPACE SHALL BE 18'. CURB RAMPS ON ACCESSIBLE ROUTES: make any changes or alterations from the

.
" SWINGS SHEET TITLE
(C.B.C.-1112A) 72 .
same without written permission from the N
MI
1/4"

"
4. THE LOADING & UNLOADING ACCESS AISLE SHALL BE MARKED BY A BORDER PAINTED BLUE. WITHIN THE BLUE BORDER, 30 .
Building Inspection Division. CROSS SECTION: HANDRAIL GRIPPING SURFACES SHALL COMPLY WITH THIS SECTION, OR THE SHAPE SHALL PROVIDE X
MA
HATCHED LINES A MAXIMUM OF 36" ON CENTER SHALL BE PAINTED A COLOR CONTRASTING WITH THE PARKING SURFACE,
PREFERABLY BLUE OR WHITE. THE WORDS "NO PARKING" SHALL BE PAINTED ON THE GROUND WITHIN EACH 5-FOOT WIDE
GENERAL. The approval of this plan and specification EQUIVALENT GRIPPING SURFACE.
A
BOTTOM
DOOR WIDTH
PLUS 42"
PUBLIC AREA
CURB RAMPS WITHIN THE BOUNDARY OF THE SITE SHALL BE CONSTRUCTED AT EACH CORNER OF STREET INTERSECTIONS & SHALL NOT be held to permit or approve the RE S
LOADING & UNLOADING ACCESS AISLE. THIS NOTICE SHALL BE PAINTED IN WHITE LETTERS NO LESS THAN 12 INCHES HIGH
AND LOCATED SO THAT IT IS VISIBLE FROM THE ADJACENT VEHICULAR WAY. (C.B.C.-1109A.8.5)
WHERE A PEDESTRIAN WAY CROSSES A CURB. THE PREFERRED & RECOMMENDED LOCATION FOR CURB RAMPS IS IN THE
CENTER OF THE CROSSWALK OF EACH STREET CORNER. WHERE IT IS NECESSARY TO LOCATE A CURB RAMP IN THE CENTER OF
GROOVING DETAIL violation of any City Ordinance or State Law. 1. CIRCULAR CROSS SECTION. THE HANDRAIL GRIPPING SURFACES WITH A CIRCULAR CROSS SECTION SHALL NOT BE
LESS THAN 1 14" NOR MORE THAN 2" IN CROSS-SECTIONAL DIMENSION.
Q'D
A
LEVEL
PLATFORM CODE
RE S
VAN ACCESSIBLE PARKING SPACE.
ONE IN EVERY EIGHT ACCESSIBLE SPACES, BUT NOT LESS THAN ONE, SHALL BE VAN ACCESSIBLE & SHALL BE CONSTRUCTED IN
THE CURB RETURN, THE STREET SURFACES SHALL BE MARKED TO IDENTIFY PEDESTRIAN CROSSWALKS, & LOWER END OF THE
CURB RAMP SHALL TERMINATE WITHIN SUCH CROSSWALK AREAS. CURB RAMPS DO NOT REQUIRE HANDRAILS. 11A-3K - CURB 2. NONCIRCULAR CROSS SECTION. HANDRAIL GRIPPING SURFACES WITH A NONCIRCULAR CROSS SECTION SHALL
Q'D INTERMIDIATE
TURNING
REFERENCES
ISSUED BY
(C.B.C.-1112A.1) DETAIL HAVE A PERIMETER DIMENSION OF 4" MIN. AND 6 14" MAX., AND A CROSS-SECTION DIMENSION OF 2 1 4" MAX.
ACCORDANCE WITH THE FOLLOWING: PLATFORM
OBSTRUCTIONS. Community Development Department FITTINGS: HANDRAILS SHALL NOT ROTATE WITHIN THEIR FITTINGS. (C.B.C.-1114A.6.2.7) 11A-6D (a) RAMP WITH INTERMEDIATE 11A-6D (b) RAMP LANDING AT DOORWAY
1. EACH VAN-ACCESSIBLE PARKING SPACE SHALL BE 17 FEET WIDE MINIMUM, AND SHALL PROVIDE EITHER OF THE SHEET NO.
CURB RAMPS SHALL BE LOCATED OR PROTECTED TO PREVENT OBSTRUCTION BY PARKED CARS. BUILT-UP CURB RAMPS SHALL SWITCH BACK PLATFORM
FOLLOWING:
1.1 A 12-FOOT WIDE MINIMUM PARKING AREA AND A 5-FOOT WIDE MINIMUM LOADING & UNLOADING ACCESS AISLE.
BE LOCATED SO THAT THEY DO NOT PROJECT INTO VEHICULAR TRAFFIC LANES, PARKING SPACES, OR THE ADJACENT LOADING By: Ann Rosendale EDGE PROTECTION: RAMPS AND RAMP LANDINGS SHALL BE PROVIDED WITH A CONTINUOUS AND UNINTERRUPTED
BARRIER ON EACH SIDE ALONG THE ENTIRE LENGTH IN COMPLIANCE WITH SECTIONS 1010.10 AND 1010.10.1(FIG 11A-5A)

A9-1.1
& UNLOADING ACCESS AISLE. (C.B.C.-1112A.2)
1.2 A 9-FOOT WIDE MINIMUM PARKING AREA AND AN 8-FOOT WIDE MINIMUM LOADING & UNLOADING ACCESS AISLE. on Jan 20, 2023
WIDTH OF CURB RAMPS. NOTE: EXTENDED FLOORS OR GROUND SURFACES, AS PERMITTED IN SECTION 1010.10.2, ARE NOT ALLOWED FOR RAMPS 11A-6D - RAMP LANDING &
2. THE MINIMUM LENGTH OF EACH SPACE SHALL BE 18'. (C.B.C.-1109A.8.6) AND RAMP LANDINGS PART OF AN ACCESSIBLE ROUTE. DOORWAY
CURB RAMPS SHALL BE A MIN. OF 48" IN WIDTH. (C.B.C.-1112A.3)
(C.B.C.-1114A.6.2.4-5)
 NOTE: 60"
1. REFER TO SHEETS A9-1.5 FOR RESIDENTIAL UNIT ACCESSIBILITY REQUIREMENTS. HANDRAIL CONFIGURATION. (C.B.C.-1123A.6.2)
44" 60" 44"
2. ALL INFORMATION IS BASED ON C.B.C. 2019

JOB COPY
MIN. HANDRAIL HEIGHTS. CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS. (C.B.C.-1138A.1.4)
THE TOP OF HANDRAILS SHALL BE 34" TO 38" ABOVE THE NOSING OF THE TREADS. (C.B.C.-1123A.6.2.1)
EXTERIOR STAIRWAYS: (C.B.C.- 1126A.3.2.1#1) SIZE AND APPROACH.
(C.B.C.-1115A) THE MIN. CLEAR FLOOR OR GROUND SPACE SHALL BE 30" BY 48". (FIG. 11A-1G) (C.B.C.-1138A.1.4.1)
ALL IDEAS, DESIGN ARRANGEMENTS AND PLANS INDICATED OR REPRESENTED BY THIS DRAWING ARE OWNED BY AND THE PROPERTY OF ARK ARCHITECTS, INC. AND WERE CREATED EVOLVED AND DEVELOPED FOR USE ON AND IN CONNECTION WITH THE SPECIFIED PROJECT. NONE OF SUCH IDEAS ARRANGEMENTS OR PLANS SHALL BE USED BY OR DISCLOSED TO ANY PERSON FIRM OR CORPORATION FOR ANY PURPOSE WHATSOEVER WITHOUT THE WRITTEN PERMISSION OF ARK ARCHITECTS, INC.
HANDRAIL CONTINUITY. (C.B.C.- 1126A.3.2.1 #2)

GENERAL. EXTERIOR STAIRWAYS SERVING FLOORS OR DWELLING UNITS REQUIRED TO BE ACCESSIBLE SHALL COMPLY
HANDRAILS ON ALL STAIRWAYS SHALL BE CONTINUOUS WITHIN THE FULL LENGTH OF EACH STAIR FLIGHT, INSIDE
HANDRAILS ON SWITCHBACK OR DOGLEG STAIRS SHALL BE CONTINUOUS BETWEEN STAIR FLIGHTS. (C.B.C.-1123A.6.2.2)
PULL
SIDE 24" CLEAR @
12" RELATIONSHIP OF MANEUVERING CLEARANCES TO WHEELCHAIR SPACES. A R K

44"

44"
WITH THIS SECTION. MIN. PUSH ONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR OR GROUND SPACE FOR A WHEELCHAIR SHALL ADJOIN OR
MIN. EXTERIOR
PROVIDE ADDITIONAL OVERLAP AN ACCESSIBLE ROUTE OR ADJOIN ANOTHER WHEELCHAIR CLEAR FLOOR SPACE. IF A CLEAR FLOOR SPACE IS

60"
HANDRAIL EXTENSION. DOORS SIDE

MIN.
60"
OPEN RISERS. OPEN RISERS SHALL NOT BE PERMITTED ALONG ACCESSIBLE ROUTES. AT THE TOP OF STAIR FLIGHTS, HANDRAILS SHALL EXTEND A MIN. OF 12" HORIZONTALLY ABOVE LANDINGS, BEGINNING SPACE IF DOOR HAS LOCATED IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR A PART OF THREE SIDES, ADDITIONAL MANEUVERING
ARCHITECTS, INC.

MIN.
18" CLEAR @ INTERIOR

48"
DIRECTLY ABOVE THE FIRST RISER NOSING. EXTENSIONS SHALL RETURN TO A WALL, GUARD, OR THE WALKING BOTH LATCH & CLOSER CLEARANCES SHALL BE PROVIDED AS SHOWN IN (FIG. 11A-1H). (C.B.C.-1138A.1.4.2)
16" 44" MIN. DOORS
EXCEPTIONS: SURFACE, OR SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT STAIR FLIGHT. (C.B.C.-1126A.3.2.1#3)
1. AN OPENING OF NOT MORE THAN 1/2 " MAY BE PERMITTED BETWEEN THE BASE OF THE RISER AND THE TREAD.

OR LESS
2. RISERS CONSTRUCTED OF GRATING CONTAINING OPENINGS OF NOT MORE THAN 1/2 " MAY BE PERMITTED. AT THE BOTTOM OF THE STAIR FLIGHTS, HANDRAILS SHALL EXTEND AT THE SLOPE OF THE STAIR FLIGHT FOR A NOTE: Faramarz Jabbari, AIA

15"
(C.B.C.-1115A.2)

MAX.
(a) MIN. (b) MIN. WIDTH FOR (c) PASSING METHODS FOR CORRIDORS W/LENGTH DISTANCE EQUAL TO ONE TREAD DEPTH BEYOND THE LAST RISER NOSING. SUCH EXTENSION SHALL CONTINUE WITH 12" ALL DIMENSIONS

24"

30"
CORRIDOR CORRIDORS OVER 200' OVER 200' AND WIDTH LESS THAN 60" MIN. HORIZONTAL EXTENSION, SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT STAIR FLIGHT, OR SHALL SHOWN ARE MIN. CLEAR
NOSING. NOSING SHALL NOT PROJECT MORE THAN 1 1/4" PAST THE FACE OF THE RISER BELOW. RISERS SHALL BE SLOPED RETURN TO A WALL, GUARD, OR THE WALKING SURFACE. HANDRAIL HORIZONTAL EXTENSIONS SHALL BE IN THE SAME (C.B.C.-1126A.3.2 & DIMENSIONS FINISH TO
WIDTH

48"
OR THE UNDERSIDE OF THE NOSING SHALL HAVE AN ANGLE NOT MORE THAN 30° FROM THE VERTICAL (FIG.11A-6A). FRONT APPROACH 2240
DIRECTION AS THE STAIR FLIGHTS. (FIG. 11A-6A & 6E) (C.B.C.-1123A.6.2.3) 1132A.5.2) FINISH.
(C.B.C.-1115A.4) NOTE: (C.B.C.-1126A.3.2.1) Faraday Road
CORRIDOR OVER 200 FEET
ALL DIMENSIONS 48"
STRIPING FOR THE VISUALLY IMPAIRED. EXTERIOR STAIRS SERVING BUILDINGS ON A SITE CONTAINING MULTIFAMILY (FIG. 11A-1L)
SHOWN ARE MIN.
DWELLING UNITS SHALL HAVE THE UPPER APPROACH AND ALL TREADS MARKED BY A STRIPE PROVIDING CLEAR VISUAL CLEAR DIMENSIONS (FIG. 11B-305.5) (FIG. 11B-305.5)
54" Carlsbad, California
CONTRAST. THE STRIPE SHALL BE A MIN. OF 2" WIDE TO A MAX. OF 4" WIDE PLACED PARALLEL TO, AND NOT MORE THAN 1" CHANGES IN LEVEL ON ACCESSIBLE ROUTES. (C.B.C.-1121A) FINISH TO FINISH. 30"
MIN.
FROM, THE NOSE OF THE STEP OR UPPER APPROACH. THE STRIPE SHALL EXTEND THE FULL WIDTH OF THE STEP OR 92008
12"
UPPER APPROACH AND SHALL BE OF MATERIAL THAT IS AT LEAST AS SLIP RESISTANT AS THE OTHER TREADS OF THE CHANGES IN LEVEL NOT EXCEEDING 12". MIN. PULL (a) FORWARD APPROACH (b) PARALLEL APPROACH Tel: (858) 792-5997
STAIR. A PAINTED STRIPE SHALL BE ACCEPTABLE. GROOVES SHALL NOT BE USED TO SATISFY THIS REQUIREMENT. ABRUPT CHANGES IN LEVEL ALONG ANY ACCESSIBLE ROUTE SHALL NOT EXCEED 12". WHEN CHANGES IN LEVEL DO LANDING SIDE
PUSH Fax: (858) 792-5858

MIN.

44" MIN.
(C.B.C.-1115A.5) 36"

60"
OCCUR, THEY SHALL BE BEVELED WITH A SLOPE NO GREATER THAN 1 UNIT VERT. IN 2 UNITS HORIZ. CHANGES IN LEVEL STAIR HANDRAILS

OR MORE
SIDE
MAY NOT EXCEED 14" MAY BE VERTICAL. (C.B.C.-1121A.1) (FIG. 11A-6E)

X
X

24"
EXTERIOR STAIRWAY HANDRAILS

30"
CHANGES GREATER THAN 12". MIN.
WHERE REQUIRED. STAIRWAYS SHALL HAVE HANDRAILS ON EACH SIDE, INTERMEDIATE HANDRAILS SHALL BE LOCATED CHANGES IN LEVEL GREATER THAN 12" SHALL BE MADE BY MEANS OF A SLOPED SURFACE NOT GREATER THAN 1 UNIT 09/12/2022
EQUIDISTANT FROM THE SIDES OF THE STAIRWAY & COMPLY WITH SECTION 1012.9. VERT. IN 20 UNITS HORIZ., OR A CURB RAMP, RAMP, ELEVATOR OR PLATFORM (WHEELCHAIR) LIFT. (C.B.C.-1121A.2) A SECOND CITY SUBMITTAL
INNER
HANDRAIL (C.B.C.- 1126A.3.2.2 #1) 48" 1'-0" 10/26/2022
EXCEPTION: STAIRWAYS SERVING AN INDIVIDUAL DWELLING UNIT MAY HAVE ONE HANDRAIL, EXCEPT THAT STAIRWAYS HINGE - SIDE APPROACH NOTE: Y= 48" MIN. IF B THIRD CITY SUBMITTAL
1
OPEN ON ONE OR BOTH SIDES SHALL HAVE HANDRAILS ON THE OPEN SIDE OR SIDES. INTERIOR RAMPS & LANDINGS ON ACCESSIBLE ROUTES. 1 2" (C.B.C.-1126A.3.2.2) DOOR HAS BOTH
(FIG. 11B-305.7.1) (FIG. 11B-305.7.2) NOTE: IF X>15", THEN AN
(C.B.C.-1115A.6.1) (C.B.C.-1122A) LATCH & CLOSER 30" 6"
(C.B.C.-1126A.3.2.2 #2) ADDITIONAL 3 ----
MANEUVERING
HANDRAIL CONFIGURATION. (C.B.C.-1115A.6.2) X: EXTENSION OF HANDRAIL
NOTE: IF X>24", THEN AN CLEARANCE OF 12" SHALL
WIDTH. SHALL BE EQUAL TO THE 4
ADDITIONAL BE PROVIDED AS SHOWN. ----
HANDRAIL HEIGHTS. THE TOP OF HANDRAILS SHALL BE 34" TO 38" ABOVE THE NOSING OF THE TREADS. (C.B.C.-1115A.6.2.1) THE CLEAR WIDTH OF RAMPS SHALL BE CONSISTENT WITH THE REQUIREMENTS IN CHAPTER 10 OF THIS CODE, BUT IN NO TREAD WIDTH PLUS 12".
MANEUVERING
CASE SHALL BE LESS THAN 48 INCHES.
PULL PUSH

60' MIN.
NOTE: INNER HANDRAIL AT CLEARANCE OF 6" SHALL 5 ----
HANDRAIL CONTINUITY. HANDRAILS ON ALL STAIRWAYS SHALL BE CONTINUOUS WITHIN THE FULL LENGTH OF EACH STAIR

44" MIN.
SIDE SIDE BE PROVIDED AS SHOWN.
FLIGHT. INSIDE HANDRAILS ON SWITCHBACK OR DOGLEG STAIRS SHALL BE CONTINUOUS BETWEEN STAIR FLIGHTS. 1
HANDRAILS MAY PROJECT INTO THE REQUIRED CLEAR WIDTH OF THE RAMP AT EACH SIDE 3 2" MAX. AT THE HANDRAIL LANDINGS OF STAIRS THAT MIN. CLEAR FLOOR SPACE FOR

MIN.
DN.

Y
12"
(C.B.C.-1115A.6.2.2) HEIGHT. CURBS, WHEEL GUIDES AND/OR APPURTENANCES SHALL NOT PROJECT INTO THE REQUIRED CLEAR WIDTH OF UP DOUBLE BACK OR IMMEDIATELY 24" MIN. 24" WHEELCHAIRS (FIG. 11A-1H) 6 ----

X
RAMPS. TURN SHALL BE CONTINUOUS & MIN.
(C.B.C.- 1126A.3.2.1 #1)
HANDRAIL EXTENSION. AT THE TOP OF STAIR FLIGHTS, HANDRAILS SHALL EXTEND A MIN. OF 12" HORIZONTALLY ABOVE NEED NOT EXTEND INTO
LANDING LANDING OR PATH OF TRAVEL. 7 ----
LANDINGS, BEGINNING DIRECTLY ABOVE THE FIRST RISER NOSING. EXTENSIONS SHALL RETURN TO A WALL, GUARD, OR EXCEPTION: THE CLEAR WIDTH OF RAMPS SERVING ACCESSIBLE ENTRANCES TO COVERED MULTIFAMILY DWELLINGS GRATINGS.
THE WALKING SURFACE, OR SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT STAIR FLIGHT. WITH AN OCCUPANT LOAD OF 10 OR LESS MAY BE 36 INCHES MINIMUM BETWEEN HANDRAILS. GUARDRAIL MAY LATCH - SIDE APPROACH GRATINGS LOCATED IN GROUND & FLOOR SURFACES ALONG ACCESSIBLE ROUTES SHALL BE LIMITED TO SPACES NO
(C.B.C.-1122A.1) BE REQUIRED (C.B.C.- 1126A.3.2.3) NOTE: Y= 48" MIN. IF GREATER THAN 12" WIDE IN ONE DIRECTION. IF GRATINGS HAVE ELONGATED OPENINGS, THEY SHALL BE PLACED SO THAT 8 ----
AT THE BOTTOM OF STAIR FLIGHTS, HANDRAILS SHALL EXTEND AT THE SLOPE OF THE STAIR FLIGHT FOR A DISTANCE DOOR HAS CLOSER THE LONG DIMENSION IS PERPENDICULAR TO THE DOMINATE DIRECTION OF TRAFFIC. (C.B.C.-1138A.1.4.3.1)
EQUAL TO ONE TREAD DEPTH BEYOND THE LAST RISER NOSING. SUCH EXTENSION SHALL CONTINUE WITH 12" MIN. SLOPE. (C.B.C.-1126A.3.2.3 #2) 9 ----
HORIZONTAL EXTENSION, SHALL BE CONTINUOUS TO THE HANDRAIL OF AN ADJACENT STAIR FLIGHT, OR SHALL RETURN TO THE MAX. SLOPE OF RAMP ON AN ACCESSIBLE ROUTE SHALL BE NO GREATER THAN 1 UNIT VERT. IN 12 UNITS HORIZ.
HANDRAIL PROJECTIONS.
A WALL, GUARD, OR THE WALKING SURFACE. HANDRAIL HORIZONTAL EXTENSIONS SHALL BE IN THE SAME DIRECTION AS (C.B.C.-1122A.2) LONG
HANDRAILS PROJECTING FROM A WALL SHALL HAVE A SPACE OF 1 12" BETWEEN THE WALL & THE HANDRAIL.
THE STAIR FLIGHTS. (FIGURES 11A-6A & 6E). (C.B.C.-1115A.6.2.3) DIMENSION ARIZONA # : 27259
CROSS SLOPE. HANDRAILS MAY BE LOCATED IN A RECESS IF THE RECESS IS A MAX. OF 3" DEEP & EXTENDS AT LEAST 18" ABOVE THE PREDOMINANT
TOP OF THE RAIL. (FIG. 11A-6B) (C.B.C.-1123A.6.2.4) PERPENDICULAR
HANDRAIL PROJECTIONS. HANDRAILS PROJECTING FROM A WALL SHALL HAVE A SPACE OF 1 1/2" BETWEEN THE WALL AND THE CROSS SLOPE OF RAMP SURFACES SHALL BE NO GREATER THAN 1 UNIT VERT, IN 48 UNITS HORIZ. (C.B.C.-1122A.2.1) DIRECTION CALIFORNIA # : C15528
TO DIRECTION

.
THE HANDRAIL. HANDRAILS MAY BE LOCATED IN A RECESS IF THE RECESS IS A 3" MAX. DEEP & EXTENDS AT LEAST 18" OF TRAVEL OF TRAVEL COLORADO # : 304356
LOCATION OF LANDINGS. HANDRAIL GRIPS.
ABOVE THE TOP OF THE RAIL. (C.B.C.-1115A.6.2.4)
LANDING SHALL BE PROVIDED AT THE TOP & BOTTOM OF EACH RAMP. INTERMEDIATE LANDINGS SHALL BE PROVIDED AT HANDRAIL GRIPPING SURFACES SHALL BE CONTINUOUS ALONG THEIR LENGTH, AND SHALL NOT BE OBSTRUCTED ALONG OREGON # : 5318
INTERVALS NOT EXCEEDING 30" OF VERT. RISE & AT EACH CHANGE OF DIRECTION. LANDINGS ARE NOT CONSIDERED IN THEIR TOPS OR SIDES. THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL NOT BE OBSTRUCTED FOR MORE THAN
HANDRAIL GRIPPING SURFACES. HANDRAIL GRIPPING SURFACES SHALL BE CONTINUOUS ALONG THEIR LENGTH, AND LATCH SIDE APPROACH. NEVADA # : 2838
SHALL NOT BE OBSTRUCTED ALONG THEIR TOPS OR SIDES. THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL NOT DETERMINING THE MAX. HORIZ. DISTANCE OF EACH RAMP. (C.B.C.-1122A.3.1) 20% OF THEIR LENGTH. WHEN PROVIDED, HORIZONTAL PROJECTIONS SHALL OCCUR 1 12" MIN. BELOW THE BOTTOM OF 1/2" MAX. OPENING
THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS/GATES WITH LATCH SIDE APPROACH:
THE HANDRAIL GRIPPING SURFACE. THE DISTANCE BETWEEN HORIZONTAL PROJECTIONS AND THE BOTTOM OF THE REACH RANGES. (C.B.C.-1138A.3) TEXAS # : 16533
BE OBSTRUCTED FOR MORE THAN 20% OF THEIR LENGTH. WHEN PROVIDED, HORIZONTAL PROJECTIONS SHALL OCCUR 1 1. PULL SIDE APPROACH, DOORS/GATES WITH PULL SIDE APPROACH SHALL HAVE A LEVEL FLOOR OR LANDING NOT
1 SIZE OF TOP LANDINGS. GRIPPING SURFACE SHALL BE PERMITTED TO BE REDUCED BY 18" FOR EACH 12" OF ADDITIONAL HANDRAIL PERIMETER
2" MIN. BELOW THE BOTTOM OF THE HANDRAIL GRIPPING SURFACE. THE DISTANCE BETWEEN HORIZONTAL PROJECTIONS LESS THAN 60" IN DEPTH, & SHALL BE PROVIDED WITH A CLEAR & LEVEL AREA EXTENDING A MIN. OF 24" PAST THE UTAH # : 7288093-0301
TOP LANDINGS SHALL NOT BE LESS THAN 60" WIDE. TOP LANDINGS SHALL HAVE A MIN. LENGTH OF NOT LESS THAN 60" IN DIMENSION THAT EXCEEDS 4". FORWARD REACH.
AND THE BOTTOM OF THE GRIPPING SURFACE SHALL BE PERMITTED TO BE REDUCED BY 18" FOR EACH 12" OF ADDITIONAL STRIKE EDGE ON THE APPROACH SIDE OF THE DOOR/ GATE (FIG. 11A-8A(c))
THE DIRECTION OF THE RAMP RUN. (FIG. 11A-6C) (C.B.C.-1122A.3.2) 1. UNOBSTRUCTED: WHEN THE CLEAR FLOOR SPACE ALLOWS ONLY FORWARD APPROACH TO AN OBJECT, THE MAX. WASHINGTON # : 8895
HANDRAIL PERIMETER DIMENSION THAT EXCEEDS 4". (C.B.C.-1115A.6.2.5) 2. PUSH SIDE APPROACH, DOORS/GATES WITH PUSH SIDE APPROACH SHALL HAVE A LEVEL FLOOR OR LANDING NOT
HANDRAIL GRIPPING SURFACES AND ANY SURFACES ADJACENT TO THEM SHALL BE FREE OF SHARP OR ABRASIVE HIGH FORWARD REACH ALLOWED SHALL BE 48" & THE MIN. LOW FORWARD REACH SHALL BE UNOBSTRUCTED & NO
LESS THAN 44" IN DEPTH, & SHALL BE PROVIDED WITH A CLEAR & LEVEL AREA EXTENDING A MIN. OF 24" PAST THE
SIZE OF BOTTOM AND INTERMEDIATE LANDINGS. ELEMENTS, AND SHALL HAVE ROUNDED EDGES. (C.B.C.-1123A.6.2.5) LESS THAN 15" ABOVE THE FLOOR. (FIG. 11A-1I(A).
CROSS SECTION. HANDRAIL GRIPPING SURFACES SHALL COMPLY WITH THIS SECTION, OR THE SHAPE SHALL PROVIDE STRIKE EDGE ON THE APPROACH SIDE OF THE DOOR/GATE. DOORS/GATES WITH THE CLOSER SHALL HAVE A LEVEL ADDRESS:
THE MIN. WIDTH OF BOTTOM & INTERMEDIATE LANDINGS SHALL NOT LESS THAN THE WIDTH OF THE RAMP. INTERMEDIATE 2. OBSTRUCTED HEIGHT REACH: THE HIGH FORWARD REACH IS OVER AN OBSTRUCTION, THE CLEAR FLOOR SPACE
EQUIVALENT GRIPPING SURFACE. FLOOR OR LANDING NOT LESS THAN 48" DEPTH AT THE PUSH SIDE OF THE DOOR/GATE. (FIG. 11A-8A(c))
LANDINGS SHALL HAVE A LENGTH IN THE DIRECTION OF RAMP RUN OF NOT LESS THAN 60". BOTTOM LANDINGS SHALL CROSS SECTION. HANDRAIL GRIPPING SURFACES SHALL COMPLY WITH THIS SECTION, OR THE SHAPE SHALL PROVIDE SHALL EXTEND BENEATH THE ELEMENT FOR DISTANCE NOT LESS THAN THE REACH DEPTH OVER THE OBSTRUCTION.
(C.B.C.-1126A.3.2.3) 1590 BARTLETT LN
EQUIVALENT GRIPPING SURFACE.

1548, 1554, 1560, 1566, 1572, 1578, 1584, & 1590 Bartlett
HAVE A LENGTH IN THE DIRECTION OF RAMP RUN OF NOT LESS THAN 72". (C.B.C.-1122A.3.3) THE HIGH FORWARD REACH SHALL BE 48" MAX. WHEN THE REACH DEPTH EXCEEDS 20" BUT IS NOT MORE THAN 25"
1. CIRCULAR CROSS SECTION. THE HANDRAIL GRIPPING SURFACES WITH A CIRCULAR CROSS SECTION SHALL NOT BE SACRAMENTO, CA 95815
THE HIGH FORWARD REACH SHALL BE 44" MAX. (FIG. 11A-1I(B) .
LESS THAN 1 14" NOR MORE THAN 2" IN CROSS-SECTIONAL DIMENSION. SPACE BETWEEN CONSECUTIVE DOORS.
ENCROACHMENT OF DOORS. 1. CIRCULAR CROSS SECTION. THE HANDRAIL GRIPPING SURFACES WITH A CIRCULAR CROSS SECTION SHALL NOT BE (C.B.C.-1138A.3.1)
THE MIN. SPACE BETWEEN TWO HINGED OR PIVOTED DOORS IN SERIES, SERVING OTHER THAN A REQUIRED EXIT
2. NONCIRCULAR CROSS SECTION. HANDRAIL GRIPPING SURFACES WITH A NONCIRCULAR CROSS SECTION SHALL HAVE DOORS IN ANY POSITION SHALL NOT REDUCE THE MIN. DIMENSION OF THE LANDING TO LESS THAN 42" & SHALL NOT LESS THAN 1 14" NOR MORE THAN 2" IN CROSS-SECTIONAL DIMENSION.
STAIRWAY, SHALL PROVIDE A MIN. 48" PLUS THE WIDTH OF THE DOOR SWINGING INTO THE SPACE. DOORS IN A SERIES
A PERIMETER DIMENSION OF 4" MIN. AND 6 14" MAX., AND A CROSS-SECTION DIMENSION OF 2 14" MAX. REDUCE THE REQUIRED WIDTH BY MORE THAN 3" WHEN FULLY OPEN. (FIG. 11A-6D) (C.B.C.-1122A.3.4) SHALL SWING EITHER IN THE SAME DIRECTION OR AWAY FROM THE SPACE BETWEEN THE DOORS/GATES. SIDE REACH.
2. NONCIRCULAR CROSS SECTION. HANDRAIL GRIPPING SURFACES WITH A NONCIRCULAR CROSS SECTION SHALL 1. UNOBSTRUCTED. WHEN A CLEAR FLOOR SPACE ALLOWS PARALLEL APPROACH TO AN ELEMENT, AND THE SIDE
(C.B.C.-1115A.6.2.6) (FIG. 11A-8G & 8H)
CHANGE OF DIRECTION. HAVE A PERIMETER DIMENSION OF 4" MIN. AND 6 14" MAX., AND A CROSS-SECTION DIMENSION OF 2 1 4" MAX. REACH IS UNOBSTRUCTED, THE HIGH SIDE REACH SHALL BE 48" MAX.& THE LOW SIDE REACH SHALL BE 15" MIN.
INTERMEDIATE LANDINGS AT A CHANGE OF DIRECTION SHALL BE SIZED TO PROVIDE 60" TURNING SPACE. INTERMEDIATE (C.B.C.-1123A.6.2.6) ABOVE THE FINISH FLOOR (FIG. 11A-1J)(a & b).
FITTINGS: HANDRAILS SHALL NOT ROTATE WITHIN THEIR FITTINGS. (C.B.C.-1115A.6.2.7) WHERE THE DOOR OPENS INTO A STAIR OR SMOKEPROOF ENCLOSURE, THE LANDING NEED NOT HAVE A MIN. LENGTH OF
& BOTTOM LANDINGS AT A CHANGE OF DIRECTION IN EXCESS OF 30° SHALL HAVE A LENGTH IN THE DIRECTION OF RAMP 60". (FIG. 11A-8H) (C.B.C.-1126A.3.3)
RUN OF NOT LESS THAN 72". (FIG. 11A-6C & 6D) (C.B.C.-1122A.3.6) FITTINGS: HANDRAILS SHALL NOT ROTATE WITHIN THEIR FITTINGS. (C.B.C.-1123A.6.2.7) EXCEPTIONS:
HAND-ACTIVATED DOOR HARDWARE 1. AN OBSTRUCTION SHALL BE PERMITTED BETWEEN THE CLEAR FLOOR SPACE AND THE ELEMENT WHEN THE
RAMP HEIGHT. HAND-ACTIVATED DOOR LATCHING, LOCKING & OPENING HARDWARE SHALL BE CENTERED BETWEEN 30" & 44" ABOVE DEPTH OF OBSTRUCTION IS 10" MAX.
HAZARDS ON ACCESSIBLE ROUTES. (C.B.C.-1116A) 2. BOOKSHELVES SHALL BE PERMITTED TO BE 54" MAX. ABOVE FINISH FLOOR. BOOKSHELVES MAYBE
RAMPS MORE THAN 30" ABOVE THE ADJACENT FLOOR OR GROUND AND OPEN ON ONE OR BOTH SIDES SHALL BE THE FLOOR.
PROVIDED WITH GUARDRAILS. GUARDRAILS SHALL BE CONTINUOUS FROM THE TOP TO THE BOTTOM OF THE RAMP. HAZARDS ON ACCESSIBLE ROUTES. GREATER THAN 54" ABOVE FINISH FLOOR WHEN AN ATTENDANT IS AVAILABLE TO ASSIST PERSONS WITH DISABILITIES.
WARNING CURBS. ABRUPT CHANGES IN LEVEL EXCEEDING 4" IN VERT. DIMENSION, SUCH AS CHANGES IN LEVEL AT (C.B.C.-1125A)
(C.B.C.-1122A.4) EXCEPTION: ACCESS GATES IN BARRIER WALLS AND FENCES PROTECTING POOLS, SPAS, & HOT TUBS SHALL BE
PLANTERS OR FOUNTAINS LOCATED IN OR ADJACENT TO WALKS, SIDEWALKS OR OTHER PEDESTRIAN WAYS SHALL BE 2. OBSTRUCTED HIGH REACH. WHEN A CLEAR FLOOR SPACE ALLOWS A PARALLEL APPROACH TO AN ELEMENT AND THE
PERMITTED TO HAVE OPERABLE PARTS OF THE RELEASE OF LATCH ON SELF-LATCHING DEVICES AT 54" MAX. ABOVE

D E V E L O P M E N T
IDENTIFIED BY CURBS OR OTHER APPROVED BARRIERS PROJECTING AT LEAST 6" IN HEIGHT ABOVE THE WALK OR HIGH SIDE REACH IS OVER AN OBSTRUCTION, THE HEIGHT OF OBSTRUCTION SHALL BE 34" MAX. AND THE DEPTH OF
SIDEWALK SURFACE TO WARN THE BLIND OF A POTENTIAL DROP-OFF. WARNING CURBS. THE FINISHED FLOOR OR GROUND PROVIDED THE SELF LATCHING DEVICES ARE NOT ALSO THE SELF LOCKING DEVICES
OPERATED BY MEANS OF A KEY, ELECTRONIC OPENER OR INTEGRAL COMBINATION LOCK. THE OBSTRUCTION SHALL BE 24" MAX. THE HIGH SIDE REACH SHALL BE 48" MAX FOR REACH DEPTH OF 10" MAX.
ABRUPT CHANGES IN LEVEL EXCEEDING 4" IN VERTICAL DIMENSION, SUCH AS CHANGES IN LEVEL OF PLANTERS, OR
RAMP HANDRAILS. (C.B.C.-1122A.5) (C.B.C.-1126A.6) WHEN THE REACH DEPTH EXCEEDS 10" BUT NO MORE THAN 24", THE HIGH SIDE REACH SHALL BE 46" MAX
EXCEPTIONS: FOUNTAINS LOCATED IN OR ADJACENT TO WALKS, HALLS, CORRIDORS, PASSAGEWAYS, AISLES, PEDESTRIAN WAYS &
(FIG. 11A-1J(c)).
1. BETWEEN A WALK OR SIDEWALK & AN ADJACENT STREET OR DRIVEWAY. WHERE REQUIRED. OTHER CIRCULATION SPACES SHALL BE IDENTIFIED BY CURBS PROJECTING AT LEAST 6" IN HEIGHT ABOVE THE WALK OR SMOOTH SURFACE.
HANDRAILS SHALL BE PROVIDED AT EACH SIDE OF RAMPS WHEN THE SLOPE EXCEEDS 1 UNIT VERT. IN 20 UNITS HORIZ. SIDEWALK SURFACE TO WARN THE BLIND OF A POTENTIAL DROP-OFF. SWINGING DOOR OR GATE SURFACES WITHIN 10 INCHES OF THE FINISH FLOOR OR GROUND MEASURED VERTICALLY EXCEPTION: KITCHEN COUNTERTOPS IN DWELLING UNITS, AND THE TOP OF WASHING MACHINES AND CLOTHES
2. WHEN A GUARDRAIL OR HANDRAIL IS PROVIDED WITH EDGE PROTECTION IN ACCORDANCE WITH SECTION 1010.10.1 SHALL HAVE A SMOOTH SURFACE ON THE PUSH SIDE EXTENDING THE FULL WIDTH OF THE DOOR OR GATE. PARTS DRYER SHALL BE PERMITTED TO BE 36" MAX. ABOVE FINISH FLOOR.
(C.B.C.-1116A.1) EXCEPTION: WHEN A GUARDRAIL OR HANDRAILS IS PROVIDED WITH EDGE PROTECTION IN ACCORDANCE WITH SECTION
EXCEPTIONS: CREATING HORIZONTAL OR VERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN 116" OF THE SAME PLANE AS THE (C.B.C.-1138A.3.2)
1. CURB RAMPS. 1010.10.1. (C.B.C.-1125A.1) OTHER AND BE FREE OF SHARP OR ABRASIVE EDGES. CAVITIES CREATED BY ADDED KICK PLATES SHALL BE CAPPED.
HEADROOM CLEARANCE. WALKS, PEDESTRIAN WAYS AND OTHER CIRCULATION SPACES WHICH ARE PART OF THE 2. RAMPS THAT SERVE AN INDIVIDUAL DWELLING UNIT MAY HAVE ONE HANDRAIL, EXCEPT THAT RAMPS OPEN ON ONE OR
REQUIRED EGRESS SYSTEM SHALL HAVE A MINIMUM CLEAR HEADROOM AS REQUIRES IN SECTION 1103.2 : NOT LESS HEADROOM CLEARANCE. EXCEPTIONS: 48" 48"
BOTH SIDES SHALL HAVE HANDRAILS PROVIDED ON THE OPEN SIDE OR SIDES.
WALKS, HALLS, CORRIDORS, PASSAGEWAYS, AISLES, PEDESTRIAN WAYS & OTHER CIRCULATION SPACES WHICH ARE MIN.

GATEWAY
THAN 7'-6". OTHER WALKS, PEDESTRIAN WAYS & CIRCULATION SPACES SHALL HAVE A MIN. CLEAR HEADROOM OF 80" (C.B.C.-1122A.5.1) 1. AUTOMATIC DOORS OR GATES.

VILLAGE-PHASE 2
(6'-8"). IF THE VERTICAL CLEARANCE OF AN AREA ADJOINING AN ACCESSIBLE ROUTE IS REDUCED TO LESS THAN 80" PART OF THE REQUIRED EGRESS SYSTEM SHALL HAVE A MIN. CLEAR HEADROOM AS REQUIRED IN SECTION 1003.2. OTHER 2. TEMPERED GLASS DOORS WITHOUT STILES & HAVING A BOTTOM RAIL OR SHOE WITH THE TOP LEADING EDGE
NOMINAL DIMENSION, A GUARDRAIL OR OTHER BARRIER HAVING ITS LEADING EDGE AT OR BELOW 27" ABOVE THE HANDRAIL CONFIGURATION. (C.B.C.-1122A.5.2) WALKS, PEDESTRIAN WAYS & CIRCULATION SPACES SHALL HAVE A MIN. CLEAR HEADROOM OF 80" (6'-8") TAPERED AT 60° MINIMUM FROM THE HORIZONTAL.
(a) UNOBSTRUCTED FORWARD REACH

MIN.
FINISHED FLOOR SHALL BE PROVIDED. 3. DOORS/GATES THAT DO NOT EXTEND TO WITHIN 10" OF THE FINISH FLOOR OR GROUND.

30"
48" MAX.
EXCEPTION: DOORWAYS & ARCHWAYS LESS THAN 24" IN DEPTH MAY HAVE A MIN. CLEAR HEADROOM OF 80" (6'-8")
HANDRAIL HEIGHTS. (C.B.C.-1126A.7)
EXCEPTION: DOORWAYS AND ARCHWAYS LESS THAN 24" IN DEPTH MAY HAVE A MIN. CLEAR HEADROOM OF 80" (6'-8") THE TOP OF HANDRAILS SHALL BE 34" TO 38" ABOVE THE RAMP SURFACE. (C.B.C.-1122A.5.2.1) (C.B.C.-1125A.2)
NOMINAL.

APARTMENTS
MIN.
(C.B.C.-1116A.2) OVERHANGING OBSTRUCTIONS.

15"
HANDRAIL CONTINUITY. 48" 48"
ANY OBSTRUCTION THAT OVERHANGS A PEDESTRIAN WAY SHALL BE A MIN. OF 80" (6'-8") ABOVE THE WALKING SURFACE (FIG. 11B-305.3)
HANDRAIL ON ALL RAMPS SHALL BE CONTINUOUS WITHIN THE FULL LENGTH OF EACH RAMP RUN. INSIDE HANDRAIL ON

SACRAMENTO, CALIFORNIA
MIN. MIN.
OVERHANGING OBSTRUCTIONS. ANY OBSTRUCTION THAT OVERHANGS A PEDESTRIAN WAY SHALL BE A MIN. OF 80". SWITCHBACK OR DOGLEG RAMPS SHALL BE CONTINUOUS BETWEEN RAM RUNS. (C.B.C.-1122A.5.2.2) AS MEASURED FROM THE BOTTOM OF THE OBSTRUCTION (FIG. 11A-1B). WHERE A GUY SUPPORT IS USED PARALLEL TO A
(SEE SECTION 1126A FOR DOOR REQUIRED) (FIG. 11A-1B) . PATH OF TRAVEL, INCLUDING, BUT NOT LIMITED TO, SIDEWALKS, A GUY BRACE, SIDEWALK GUY OR SIMILAR DEVICE SHALL (FIG. 11B-308.2.1)
BE USED TO PREVENT AN OVERHANGING OBSTRUCTION (SEE SECTION 1125A.2). 20" < Y < 25"
HANDRAIL EXTENSION. 20" MAX.
EXCEPTION: DOOR CLOSER & DOOR STOPS SHALL BE PERMITTED TO BE 78" MIN. ABOVE THE FINISH FLOOR. HANDRAILS SHALL EXTEND A MIN. OF 12" HORIZONTALLY ABOVE LANDINGS, BEYOND THE TOP & BOTTOM OF THE RAMP
(C.B.C.-1116A.3) RUNS. EXTENSIONS SHALL RETURN TO A WALL, GUARD, OR THE WALKING SURFACE, OR SHALL BE CONTINUOUS TO THE EXCEPTION: DOOR CLOSERS AND DOOR STOPS SHALL BE PERMITTED TO BE 78 INCHES MIN. ABOVE THE FINISH FLOOR OR
HANDRAIL OF AN ADJACENT RAMP RUN. HANDRAIL EXTENSIONS SHALL BE IN THE SAME DIRECTION AS THE RAMP RUNS GROUND. (C.B.C.-1125A.3)
(FIG. 11A-5A). (C.B.C.-1122A.5.2.3)
GENERAL REQUIREMENTS FOR ACCESSIBLE ENTRANCES, EXITS,

12" *

12" *

48" MAX.

44" MAX.
12" *

MIN.

MIN.
30"

30"
* PROVIDE THIS ADDITIONAL

MIN.

MIN.
INTERIOR ROUTES OF TRAVEL & FACILITY ACCESSIBILITY. (SEE ALSO CHAPTER 10): HANDRAIL PROJECTIONS. DOORS, GATES AND WINDOWS.

MIN.

MIN.
18"
(C.B.C.-1126A) SPACE IF DOOR IS EQUIPPED
(C.B.C.-1117A) HANDRAILS PROJECTING FROM A WALL SHALL HAVE A SPACE OF 1 12" BETWEEN THE WALL & THE HANDRAIL.
WITH BOTH A LATCH & A CLOSER
HANDRAILS MAY BE LOCATED IN A RECESS IF THE RECESS IS A MAX. OF 3" DEEP & EXTENDS AT LEAST 18" ABOVE THE TOP
NOTE: IN ADDITION TO PROVISIONS OF THIS DIVISION, INTERIOR ROUTES OF TRAVEL THAT PROVIDE ACCESS TO, OR OF THE RAIL (FIG. 11A-6B). (C.B.C.-1122A.5.2.4) WIDTH & HEIGHT OF DOORS AND GATES:
DOORWAYS WHICH PROVIDE ACCESS TO COMMON USE AREAS OR COVERED MULTIFAMILY DWELLINGS SHALL COMPLY 20" MAX. 20" < Y < 25"
EGRESS FROM, BUILDINGS FOR PERSONS WITH DISABILITIES SHALL ALSO COMPLY WITH CHAPTER 10. NOTE:
HANDRAIL GRIPPING SURFACES. WITH THE FOLLOWING: (b) BOTH DOORS X>20" X>20" X>Y X>Y
(a) DOOR IN SERIES ALL DIMENSIONS SHOWN ARE
HANDRAIL GRIPPING SURFACES SHALL BE CONTINUOUS ALONG THEIR LENGTH, AND SHALL NOT BE OBSTRUCTED ALONG 1. PERMIT THE INSTALLATION OF A DOOR OR GATE NOT LESS THAN 36" IN WIDTH, NOT LESS THAN 80" (6'-8") IN HEIGHT & VESTIBULE OPEN OUT
GENERAL. MIN. CLEAR DIMENSIONS FINISH 48" MIN. 48" 48" MIN. 48"
THEIR TOPS OR SIDES. THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL NOT BE OBSTRUCTED FOR MORE THAN PROVIDE A CLEAR OPENING OF NOT LESS THAN 32", MEASURED WITH THE DOOR POSITIONED AT THE ANGLE OF 90° (FIG. 11A-8G)
WHEN BUILDINGS ARE REQUIRED TO BE ACCESSIBLE, BUILDING FACILITIES SHALL BE ACCESSIBLE AS PROVIDED IN THIS TO FINISH.
DIVISION. WHERE SPECIFIC FLOORS OF A BUILDING ARE REQUIRED TO BE ACCESSIBLE, THE REQUIREMENTS OF THIS 20% OF THEIR LENGTH. WHEN PROVIDED, HORIZONTAL PROJECTIONS SHALL OCCUR 1 12" MIN. BELOW THE BOTTOM OF THE FROM ITS CLOSED POSITION. (FIG. 11B-308.2.2) (FIG. 11B-308.2.2)
DIVISION SHALL APPLY ONLY TO THE FACILITIES LOCATED ON ACCESSIBLE FLOORS. (C.B.C.-1117A.1) HANDRAIL GRIPPING SURFACE. THE DISTANCE BETWEEN HORIZONTAL PROJECTIONS AND THE BOTTOM OF THE GRIPPING 2. DOORS OR GATES SHALL BE CAPABLE OF OPENING AT LEAST 90°.

D E B A R T O L O
SURFACE SHALL BE PERMITTED TO BE REDUCED BY 18" FOR EACH 12" OF ADDITIONAL HANDRAIL PERIMETER DIMENSION 3. A PAIR OF DOORS OR GATES, MANUAL OR AUTOMATIC, MUST HAVE AT LEAST ONE HALF WHICH PROVIDES A CLEAR (b) FORWARD REACH OVER OBSTRUCTION
PRIMARY ENTRANCES & EXTERIOR EXIT DOORS. THAT EXCEEDS 4". WIDTH OF NOT LESS THAN 32", MEASURED WITH THE DOOR OR GATE POSITIONED AT AN ANGLE OF 90° FROM ITS
CLOSED POSITION. FORWARD REACH
ALL PRIMARY ENTRANCES & EXTERIOR GROUND FLOOR EXIT DOORS TO BUILDINGS AND FACILITIES ON ACCESSIBLE 48"
HANDRAIL GRIPPING SURFACES AND ANY SURFACES ADJACENT TO THEM SHALL BE FREE OF SHARP OR ABRASIVE 4. THE WIDTH OF ANY COMPONENT IN THE EGRESS SYSTEM SHALL NOT BE LESS THAN THE MIN. WIDTH REQUIRED BY (FIG. 11A-1I)
ROUTES SHALL BE ACCESSIBLE TO PERSONS WITH DISABILITIES. (C.B.C.-1117A.2) MIN.
ELEMENTS, AND SHALL HAVE ROUNDED EDGES. SECTION 1005.
MULTIPLE ENTRANCES. 5. REVOLVING DOORS OR GATES SHALL NOT BE USED AS REQUIRED ENTRANCES FOR PERSONS WITH DISABILITIES,
ONLY ONE ENTRANCE TO COVERED MULTIFAMILY BUILDINGS IS REQUIRED TO BE ACCESSIBLE TO ANY ONE GROUND EXCEPTION: WHERE HANDRAILS ARE PROVIDED ALONG WALKING SURFACES WITH SLOPES NOT STEEPER THAN 1 UNIT AND SHALL NOT BE PART OF AN ACCESSIBLE ROUTE.

M 8"
.
4
IN
FLOOR OF A BUILDING. EXCEPT IN CASES WHERE AN INDIVIDUAL DWELLING UNIT HAS A SEPARATE EXTERIOR ENTRANCE. VERTICAL IN 20 UNITS HORIZONTAL, THE BOTTOMS OF HANDRAIL GRIPPING SURFACES SHALL BE PERMITTED TO BE (C.B.C.-1126A.1)
WHERE THE BUILDING CONTAINS CLUSTERS OF DWELLING UNITS WITH EACH CLUSTER SHARING A DIFFERENT EXTERIOR OBSTRUCTED ALONG THEIR ENTIRE LENGTH WHERE THEY ARE INTEGRAL TO CRASH RAILS OR BUMPER GUARDS.
(C.B.C.-1122A.5.2.5) LEVEL FLOOR OR LANDING.

48"
ENTRANCE, MORE THAN ONE ENTRANCE MAY BE REQUIRED TO BE ACCESSIBLE, AS DETERMINED BY ANALYSIS OF THE

48"

48"
SITE. IN EVERY CASE, THE ACCESSIBLE ENTRANCE SHALL BE ON AN ACCESSIBLE ROUTE TO THE COVERED DWELLING THE FLOOR OR LANDING ON EACH SIDE OF AN EXIT DOOR OR GATE SHALL BE LEVEL SEE CHAPTER 10 (C.B.C.-1126A.2)

ARDEN
UNITS IT SERVES. (C.B.C.-1117A.4) EDGE PROTECTION.

MIN.

MIN.
RAMPS AND RAMP LANDINGS SHALL BE PROVIDED WITH A CONTINUOUS AND UNINTERRUPTED BARRIER ON EACH SIDE THRESHOLDS & CHANGES IN ELEVATION AT DOORS.

18"

18"
ENTRANCES FROM PARKING STRUCTURES, TUNNELS, OR ELEVATED WALKWAYS. ALONG THE ENTIRE LENGTH. (FIG. 11A-5A) THE FLOOR OR LANDING SHALL NOT BE MORE THAN 12" LOWER THAN THE TOP OF THE THRESHOLD OF THE DOORWAY.
WHERE DIRECT ACCESS FOR PEDESTRIANS IS PROVIDED FROM A PARKING STRUCTURE TO A BUILDING OF FACILITY, EACH (C.B.C.-1122A.6) (FIG. 11A-8I)
30" 10" 30" 24" MAX. 30"
DIRECT ACCESS TO THE BUILDING OR FACILITY ENTRANCE SHALL BE ACCESSIBLE. (C.B.C.-1117A.5) 8H(b) DOORS AT MAX.
1 1
CHANGES IN LEVEL BETWEEN 4" & 2" SHALL BE BEVELED WITH A SLOPE NO GREATER THAN 1 UNIT VERT. IN 2 UNITS OPPOSITE WALLS
HORIZ. CHANGES IN LEVEL GREATER THAN 1 2" SHALL BE ACCOMPLISHED BY MEANS OF A RAMP. (C.B.C.-1126A.2.1) CLEAR FLOOR SPACE CLEAR FLOOR SPACE CLEAR FLOOR SPACE
INTERIOR STAIRWAYS 32"
PARALLEL APPROACH PARALLEL APPROACH PARALLEL APPROACH
INTERIOR ROUTES OF TRAVEL: (C.B.C.-1123A) 8H(a) DOORS
MANEUVERING CLEARANCES AT DOORS. (C.B.C.-1126A.3)
(C.B.C.- 1119A) ADJACENT WALLS VESTIBULE AN ADULT SIZE
GENERAL. 30" 10" 30" 30" 24"
GENERAL. (FIG. 11A-8H) WHEELCHAIR
GENERAL. INTERIOR STAIRWAYS SERVING BUILDINGS CONTAINING COVERED MULTIFAMILY DWELLING UNITS SHALL COMPLY WITH MAX. MAX.
THE MINIMUM MANEUVERING CLEARANCE AT DOORS OR GATES SHALL COMPLY WITH SECTIONS 1126A.3.2, 1126A.3.3, AND AVERAGES 27" IN
WHEN A BUILDING OR PORTION OF THE BUILDING IS REQUIRED TO BE ACCESSIBLE OR ADAPTABLE, AN ACCESSIBLE ROUTE THIS SECTION. 1126A.3.4. THE FLOOR OR LANDING ARE WITHIN THE REQUIRED MANEUVERING CLEARANCE SHALL BE LEVEL AND CLEAR. (SERVING OTHER THAN A WIDTH. THE REQUIRED
SHALL BE PROVIDED TO ALL PORTIONS OF THE BUILDING. ACCESSIBLE BUILDING ENTRANCES & TO COVERED MULTIFAMILY THE REQUIRED LENGTH SHALL BE MEASURED AT RIGHT ANGLES TO THE PLANE OF THE DOOR OR GATE IN ITS CLOSED REQUIRED EXIT STAIRWAY) 32" CLEAR OPENING
DWELLING UNITS. THE ACCESSIBLE ROUTE SHALL, TO THE MAXIMUM EXTENT FEASIBLE, COINCIDE WITH THE ROUTE FOR OPEN RISERS. POSITION. MANEUVERING CLEARANCES SHALL EXTEND THE FULL WIDTH OF THE DOORWAY AND THE REQUIRED LATCH ALLOWS 2 12" ON EACH

48" MAX.

48" MAX.
THE GENERAL PUBLIC AND OTHER BUILDING RESIDENTS. ACCESSIBLE ROUTES SHALL NOT PASS THROUGH KITCHENS, OPEN RISERS SHALL NOT BE PERMITTED ON INTERIOR STAIRWAYS. SIDE OR HINGE SIDE CLEARANCES (STRIKE EDGE MANEUVERING CLEARANCES). (C.B.C.-1126A.3.1) SIDE FOR HANDS.

MAX.
STORAGE ROOMS, RESTROOMS, CLOSETS OR OTHER SPACES USED FOR SIMILAR PURPOSES EXCEPT WITHIN AN EXCEPTION: STAIRWAYS WITHIN AN INDIVIDUAL

46"
MAX.
INDIVIDUAL DWELLING UNIT. (C.B.C.-1123A.2)

34"
PASSAGE CLEARANCE
(FIG. 11B-5B)

MIN.

MIN.
ACCESSIBLE ROUTES SHALL BE PROVIDED AS FOLLOWS: TREADS.

15"

15"
1. WHERE MORE THAN ONE ROUTE OF TRAVEL IS PROVIDED, ALL ROUTES SHALL BE ACCESSIBLE. ALL TREAD SURFACES SHALL BE STABLE, FIRM AND SLIP RESISTANT, AND SHALL COMPLY WITH SECTION 1119A.2.
2. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE BUILDING OR FACILITY ENTRANCES WITH ALL TREADS SHALL HAVE SMOOTH, ROUNDED OR CHAMFERED EXPOSED EDGES AND NO ABRUPT EDGES AT THE NOSING
42" MIN.

SPACE ALLOWANCES & REACH RANGES IN COMMON USE AREAS:

48" MIN.

ACCESSIBLE SPACES, ELEMENTS & COVERED MULTIFAMILY DWELLING UNITS. (LOWER FRONT EDGE). (C.B.C.-1123A.3) HIGH & LOW SIDE HIGH & LOW SIDE HIGH & LOW SIDE
3. AN ACCESSIBLE ROUTE SHALL CONNECT AT LEAST ONE ACCESSIBLE PRIMARY ENTRANCE OF EACH COVERED 22" (C.B.C.-1138A) REACH LIMITS REACH LIMITS REACH LIMITS
MULTIFAMILY DWELLING UNIT WITH INTERIOR & EXTERIOR SPACES & FACILITIES THAT SERVE THE UNIT. NOSING.

@ 1:2 SLOPE
4. WHERE ELEVATORS ARE PROVIDED FOR VERTICAL ACCESS, ALL ELEVATORS SHALL BE ACCESSIBLE. NOSING SHALL NOT PROJECT MORE THAN 1 14" PAST THE FACE OF THE RISER BELOW. RISERS SHALL BE SLOPED OR THE SPACE ALLOWANCES. (C.B.C.-1138A.1)
(C.B.C.-1119A.1) UNDERSIDE OF THE NOSING SHALL HAVE AN ANGLE NOT MORE THAN 30° FROM THE VERTICAL. (FIG. 11A-6A) (a) UNOBSTRUCTED (b) SIDE REACH OVER (c) SIDE REACH OVER SIDE REACH
(C.B.C.-1123A.4) 2 SINGLE WHEELCHAIR PASSAGE WIDTH SIDE REACH OBSTRUCTION 10" MAX. OBSTRUCTION > 10" AND 24" MAX. (FIG. 11A-1J)

MAX.
1/2"
FLOOR AND GROUND SURFACES. POCKET OR HINGE 1 THE MIN. CLEAR WIDTH FOR SINGLE WHEELCHAIR PASSAGE SHALL BE 36" CONTINUOUSLY. (FIG. 11A-1E). (FIG. 11B-308.3.1) (FIG. 11B-308.3.2)
FLOOR AND GROUND SURFACES SHALL BE STABLE, FIRM, AND SLIP RESISTANT. IF CARPET OR CARPET TILE IS USED IN A STRIPING FOR THE VISUALLY IMPAIRED. FRONT APPROACH SIDE APPROACH
COMMON USE AREA OR PUBLIC USE AREA ON A GROUND OR FLOOR SURFACE, IT SHALL HAVE FIRM BACKING OR NO INTERIOR STAIRS SHALL HAVE THE UPPER APPROACH & LOWER TREAD MARKED BY A STRIPE PROVIDING CLEAR VISUAL (C.B.C.-1126A.3.4.1) (C.B.C.-1126A.3.4.3) EXCEPTION: 32" IN WIDTH IS ACCEPTABLE AT A POINT NOT TO EXCEED 24" IN LENGTH. THE SEGMENTS WITH REDUCED
BACKING. CARPET OR CARPET TILE SHALL HAVE A LEVEL LOOP, TEXTURED LOOP, LEVEL CUT PILE, OR LEVEL CUT/UNCUT CONTRAST. THE STRIPE SHALL BE A MIN. 2" WIDE TO A MAX.OF 4" WIDE PLACED PARALLEL TO, & NOT MORE THAN 1" WIDTH SHALL BE SEPARATED BY SEGMENTS THAT ARE 48" LONG MINIMUM AND 36" WIDE MINIMUM. (C.B.C.-1138A.1.1)

MAX.
CONTROL & OPERATING MECHANISMS. (C.B.C.-1138A.4)

1/4"
SLIDING DOORS
PILE TEXTURE. THE MAXIMUM PILE HEIGHT SHALL BE 12 INCH. EXPOSED EDGES OF CARPET SHALL BE FASTENED TO FLOOR FROM, THE NOSE OF THE STEP OR UPPER APPROACH. THE STRIPE SHALL EXTEND THE FULL WIDTH OF THE STEP OR
SURFACES AD HAVE TRIM ALONG THE ENTIRE LENGTH OF THE EXPOSED EDGE. CARPET EDGE TRIM SHALL COMPLY WITH (C.B.C.-1126A.3.4) WIDTH FOR TWO WHEELCHAIR PASSING.
UPPER APPROACH AND SHALL BE OF MATERIAL THAT IS AT LEAST AS SLIP RESISTANT AS THE OTHER TREADS OF THE GENERAL.
SECTION 1121A REQUIREMENTS FOR CHANGES IN LEVEL. (C.B.C.-1119A.2) SLIDING DOORS THE MIN. WIDTH FOR TWO WHEELCHAIRS TO PASS IS 60". (FIG. 11A-1E) MILESTONE:
STAIR. A PAINTED STRIPE SHALL BE ACCEPTABLE. GROOVES SHALL NOT BE USED TO SATISFY THIS REQUIREMENT. CONTROL & OPERATING MECHANISMS IN ACCESSIBLE SPACES, ALONG ACCESSIBLE ROUTES OR AS PART OF ACCESSIBLE
(C.B.C.-1126A.3.4) AN ACCESSIBLE ROUTE WITH A CLEAR WITH LESS THAN 60" SHALL PROVIDE SPACES AT INTERVALS OF 200' MAX. PASSING THIRD CITY SUBMITTAL
ELEMENTS SHALL COMPLY WITH THIS SECTION. (C.B.C.-1138A.4.1)
RECESSED DOORMATS. EXCEPTION: STRIPING IS NOT REQUIRED FOR STAIRWAYS WITHIN INDIVIDUAL DWELLING UNITS. FINISH SPACES SHALL BE EITHER: A SPACE 60" MIN. ; OR AN INTERSECTION OF TWO WALKING SURFACES PROVIDING T-SHAPED
RECESSED DOORMATS SHALL BE ADEQUATELY ANCHORED TO PREVENT INTERFERENCE WITH WHEELCHAIR TRAFFIC. (C.B.C.-1123A.5) SPACE COMPLYING WITH SECTION 1138A.1.3.1 WHERE THE BASE AND ARMS OF THE T-SHAPED SPACE EXTEND 48" MIN.

COM-2213627 to COM-2213634
FLOOR EVEN CLEAR FLOOR SPACE.
42" MIN.

(C.B.C.-1119A.2.1) BEYOND THE INTERSECTION (FIG. 11A-1L). (C.B.C.-1138A.1.2) CLEAR FLOOR SPACE COMPLYING WITH SECTION 1138A.1.4 THAT ALLOWS A FORWARD OR PARALLEL APPROACH BY A
.

INTERIOR STAIRWAY HANDRAILS. DRAWN: MH, NM

PERSON USING A WHEELCHAIR SHALL BE PROVIDED AT ALL CONTROLS AND OPERATING MECHANISMS. (C.B.C.-1138.4.2)
42" MIN.

WIDTHS. (C.B.C.-1123A.6) WHEELCHAIR TURNING SPACE.

INTERIOR ACCESSIBLE ROUTES SERVING AN OCCUPANT LOAD OF 10 OR MORE SHALL NOT BE LESS THAN 44" IN WIDTH. 24" MIN. COMPRESSED THE SPACE REQUIRED FOR A WHEELCHAIR TO MAKE A 180° TURN IS A CLEAR SPACE OF 60" DIAMETER MIN. (FIG. 11A-1D(a), CHECKED: JM
HEIGHT.
INTERIOR ACCESSIBLE ROUTES SERVING AN OCCUPANT LOAD OF LESS THAN 10 SHALL NOT BE LESS THAN 36" IN WIDTH. WHERE REQUIRED. CARPET 14" MAX. OR A T-SHAPED SPACE, (FIG. 11A-1D(b) . THE CIRCULAR TURNING SPACE SHALL BE PERMITTED TO INCLUDE KNEE AND TOE CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER THAN 48", AND NO LOWER THAN 15", ABOVE PLOT DATE: Monday, October 24, 2022
IF A PERSON IN A WHEELCHAIR MUST MAKE A TURN AROUND A CORNER OR AN OBSTRUCTION, THE MIN. CLEAR WIDTH OF STAIRWAYS SHALL HAVE HANDRAILS ON EACH SIDE. INTERMEDIATE HANDRAILS SHALL BE LOCATED EQUIDISTANT FROM BELOW THRESHOLD CLEARANCE COMPLYING WITH SECTION 1138A.2. (C.B.C.-1138A.1.3) THE FINISHED FLOOR MEASURED TO THE CENTER OF THE GRIP. IF THE REACH IS OVER AN OBSTRUCTION (F.G., WASHER &
THE ACCESSIBLE ROUTE SHALL BE SPECIFIED IN SECTION 1138A.1.5. (FIG. 11A-1C) (C.B.C.-1119A.3) THE SIDES OF THE STAIRWAY AND COMPLY WITH SECTION 1012.9. SIDE APPROACH DOORWAYS
DRYER), CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED WITHIN THE REACH RANGES SPECIFIED IN
W/OUT DOORS/ GATES T-SHAPED TURNING SPACE. SECTION 1138A.3. CONTROLS AND OPERATING MECHANISMS THAT DO NOT SATISFY THESE SPECIFICATIONS ARE E D A RC
ER
INTERIOR ACCESSIBLE ROUTES OVER 200'. EXCEPTION: STAIRWAYS SERVING AN INDIVIDUAL DWELLING UNIT MAY HAVE ONE HANDRAIL, EXCEPT THAT STAIRWAYS (C.B.C.-1126A.3.4.2) STOP OR LATCH SHALL BE WITHIN A 60 INCH SQUARE MIN. WITH ARMS AND BASE 36" WIDE MIN. EACH ARM OF THE T SHALL BE CLEAR OF ACCEPTABLE, PROVIDED THAT COMPARABLE MECHANISMS, CONTROLS, OR OUTLETS, THAT PERFORM THE SAME
INTERIOR ACCESSIBLE ROUTES THAT EXCEED 200' IN LENGTH SHALL COMPLY WITH SECTION 1138A.1.2. (FIG. 11A-1L) OPEN ON ONE OR BOTH SIDES SHALL HAVE HANDRAILS ON THE OPEN SIDE OR SIDES. OBSTRUCTIONS 12" MIN. IN EACH DIRECTION, AND THE BASE SHALL BE CLEAR OF OBSTRUCTIONS 24" MIN. THE SPACE
SIDE APPROACH R Z JA

H
FUNCTIONS, ARE PROVIDED WITHIN THE SAME AREA AND ARE ACCESSIBLE. (C.B.C.-1138A.4.3)

ST
(C.B.C.-1119A.4) (C.B.C.-1123A.6.1) SHALL BE PERMITTED TO INCLUDE KNEE AND TOE CLEARANCE COMPLYING WITH SECTION 1138A.2 PNLY AT THE END OF MA B

IT E
(C.B.C.-1126A.3.4.4)

R EG I
FA RA
THRESHOLDS EITHER THE BASE OR ONE ARM (FIG. 11A-1D(b) . (C.B.C.-1138A.1.3.1)

BA
CHANGES IN ELEVATION. (FIG. 11A-8I)

CT
INDICATES DIRECTION

RI
INTERIOR ACCESSIBLE ROUTES WHICH HAVE CHANGE IN ELEVATION SHALL BE TRANSITIONED AND COMPLY WITH SECTION 1 1/4" MAX. 1 1/4" MAX. OF APPROACH STORAGE: No. C 15528

THIRD CITY SUBMITTAL 10/26/2022

1121A OR 1122A. MANEUVERING CLEARANCE AT DOOR WAYS (C.B.C.- 1127A.11)
36" MIN.
Exp. 03/31/23
________
EXCEPTION: DOORS AND THRESHOLDS AS PROVIDED IN SECTION 1126A. (C.B.C.-1119A.5) 60°
GENERAL.
TA

IA
MIN. 32" MIN. N

S
TE
O F CA L I F O R
SWINGING DOORS AND GATES. (C.B.C.-1126A.3.2) IF FIXED STORAGE FACILITIES SUCH AS CABINETS, SHELVES, CLOSETS OR DRAWERS ARE PROVIDED WHERE ACCESS IS
12" 12"
REQUIRED BY SECTIONS 1.8.2.1.2 AND 1102A, AT LEAST ONE OF EACH TYPE OF FACILITY PROVIDED SHALL COMPLY WITH
MIN. 36" MIN. MIN.
STAIRS 60" THIS SECTION. ADDITIONAL STORAGE MAY BE PROVIDED OUTSIDE OF THE REACH RANGES SPECIFIED IN SECTION 1138A.3.

MAX.
FRONT APPROACH.THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS WITH FRONT APPROACH:

24"
60" MIN.

(FIG. 11A-1J & FIG. 11B-5D). (C.B.C.- 1127A.11.1)

MIN.
3'-0"

24" MIN.

1. PULL SIDE APPROACH, THE LEVEL FLOOR OR LANDING SHALL EXTEND IN THE DIRECTION OF THE DOOR SWING AT
MIN.
4'-0"

60" MIN.
LEAST 60". (FIG. 11A-8A) CLEAR FLOOR SPACE. PROJECT NO. 2021-051
2. PUSH SIDE APPROACH, THE LEVEL FLOOR OR LANDING SHALL EXTEND OPPOSITE THE DIRECTION OF THE DOOR SWING A CLEAR FLOOR SPACE AT LEAST 30" X 48" COMPLYING WITH SECTION 1138A.1.4 THAT ALLOWS EITHER A FORWARD OR

60" MIN.
GUARDRAILS SHALL BE LOCATED PARALLEL APPROACH BY A PERSON USING A WHEELCHAIR SHALL BE PROVIDED AT ACCESSIBLE STORAGE FACILITIES.

48"MIN.
AT LEAST 48". (FIG. 11A-8A) PROJECT PHASE .
LESS
60"

LESS ALONG OPEN-SIDED STAIRWAYS & 3. DOORS OR GATES WITH PUSH SIDE APPROACH HAVING BOTH A CLOSER & A LATCH SHALL BE PROVIDED WITH THE (C.B.C.-1127A.11.2)
THAN 48"
36" MIN.

THAN 48" LANDINGS THAT ARE LOCATED CLEAR & LEVEL AREA EXTENDING A MIN. OF 12" PAST THE STRIKE EDGE ON THE APPROACH SIDE OF THE DOOR OR SHEET TITLE
3'-6" . 3'-6" 3'-0" . 3'-0" MORE THAN 30" ABOVE THE FLOOR GATE. (FIG. 11A-8A) HEIGHT.
3'-0" 4'-0" 3'-0" OR GRADE BELOW AT ANY POINT ACCESSIBLE STORAGE SPACES AND CLOTHES RODS SHALL BE WITHIN AT LEAST ONE OF THE REACH RANGES ON
MIN. OR GREATER MIN.
MIN. MIN. MIN. MIN.
WITHIN 36" HORIZ. TO THE EDGE OF
4. STRIKE EDGE MANEUVERING SPACE. THE WIDTH OF THE LEVEL AREA ON THE SIDE TO WHICH THE DOOR OR GATE
SWINGS SHALL EXTEND AT LEAST 24" PAST THE STRIKE EDGE FOR EXTERIOR DOORS OR GATES & AT LEAST 18" PAST
32" MIN.
60" MIN.
(FIG. 11A-1J) & (FIG. 11A-1I). (C.B.C.-1127A.11.3) PUBLIC AREA

MAX.
THE OPEN SIDE.

24"
THE STRIKE EDGE FOR INTERIOR DOORS OR GATES. (C.B.C.-1126A.3.2.1)
(a) 90° TURN AROUND OBSTRUCTION (b) 180° TURN AROUND OBSTRUCTION
(C.B.C.-1015.2)
(FIG. 11B-304.3.2)
HARDWARE.
ACCESSIBLE STORAGE FACILITIES SHALL COMPLY WITH SECTION 1138A.4. TOUCH LATCHES AND U-SHAPED PULLS ARE
CODE
WIDTH OF ACCESSIBLE ROUTE 36" MIN.
AT TURNS (FIG. 11A-1C)
NOTE:
1). IF CARPET OR CARPET TILE
GUARDRAILS SHALL FORM
PROTECTIVE BARRIER NOT LESS HINGE SIDE APPROACH.
ACCEPTABLE. (C.B.C.-1127A.11.4)
REFERENCES
IS USED ON A GROUND OR THAN 42" HIGH, MEASURED THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS OR GATES WITH HINGE SIDE APPROACH: (a) 60 INCHES (b) T-SHAPED SPACE FOR 180° MIN. CLEAR WIDTH FOR MIN. CLEAR WIDTH FOR
This set of plans and specifications must be
ISSUED BY
FLOOR SURFACE, THE MAX. VERTICALLY ABOVE THE LEADING 1. PULL SIDE APPROACH, DOORS/GATES WITH PULL SIDE APPROACH SHALL BE PROVIDED WITH A LEVEL FLOOR OR DIAMETER SPACE TURN SINGLE WHEELCHAIR TWO WHEELCHAIRS
kept on the job at all times and it is unlawful to
1/4" MAX.

LANDING NOT LESS THAN 60" IN DEPTH. A CLEAR & LEVEL AREA SHALL EXTEND A MIN. OF 36" PAST THE STRIKE EDGE
MAX.

2 PILE HEIGHT SHALL BE 12". EDGE OF THE TREAD. SHEET NO.

ON THE APPROACH SIDE OF THE DOOR OR GATE (FIG. 11A-8A(b)) make any changes or alterations from the Community Development Department
1 (C.B.C.-1119A.2) (C.B.C.-1015.3)
4"

CHANGE IN LEVEL WARNING STRIPING & HANDRAIL EXTENSIONS WHEELCHAIR TURNING SPACE WHEELCHAIR PASSAGE WIDTH same without written permission from the
Ann Rosendale
1

2"

By:

A9-1.2
Building Inspection Division.
1

(FIG. 11A-1F) 2). ALL DIMENSIONS SHOWN (FIG. 11A-6A) 2. PUSH SIDE APPROACH, DOORS OR GATES WITH PUSH SIDE APPROACH SHALL HAVE A LEVEL FLOOR OR LANDING NOT (FIG. 11A-1D) (FIG. 11A-1E)
ARE MIN. CLEAR DIMENSIONS LESS THAN 44" IN DEPTH, & SHALL BE PROVIDED WITH A CLEAR & LEVEL AREA EXTENDING A MIN.OF 54" FROM THE The approval of this plan and specification
NOTE: on Jan 20, 2023
4"

FINISH TO FINISH. STRIKE EDGE OF THE DOOR/GATE JAMB PAST THE HINGE SIDE OF THE DOOR/GATE. DOORS/GATES WITH THE LATCH & SHALL NOT be held to permit or approve the
1

ALL DIMENSIONS SHOWN ARE

CLOSER SHALL HAVE A LEVEL FLOOR OR LANDING NOT LESS THAN 48" DEPTH AT THE PUSH SIDE OF THE DOOR OR violation of any City Ordinance or State Law.
(a) VERTICAL CHANGE IN (b) BEVELED CHANGE IN MIN. CLEAR DIMENSIONS
LEVEL GATE. (FIG. 11A-8A(b)) (C.B.C.-1126A.3.2.2)
LEVEL FINISH TO FINISH.
 ENCLOSURES. CONTROLS AND OPERATING MECHANISMS. CONTROLS.
ACCESSIBLE LAVATORIES. WHEN PROVIDED FOR SHOWER COMPARTMENTS, SHALL NOT OBSTRUCT CONTROLS, FAUCETS, SHOWER SPRAY UNITS. CLOTHES WASHERS & DRYERS INCLUDING STACKED CLOTHES WASHERS & DRYERS REQUIRED TO BE ACCESSIBLE SHALL TELEPHONES SHALL HAVE PUSH-BUTTON CONTROLS WHERE SERVICE FOR SUCH EQUIPMENT IS AVAILABLE. MULTIPLE-ACCOMMODATION TOILET FACILITIES, (C.B.C.-1127A.2.1)

JOB COPY
(C.B.C.-1127A.3) AND TRANSFER FROM WHEELCHAIR ONTO SHOWER SEATS. (C.B.C.-1127A.5.3.3) HAVE CONTROLS & OPERATING MECHANISMS (INCLUDING DOORS, COIN SLOTS, LINT SCREENS, DETERGENT AND BLEACH ( C.B.C.-1140A.8) SHALL HAVE THE FOLLOWING:
COMPARTMENTS) & WITHIN THE REACH RANGE OF A SEATED USER. CONTROLS & OPERATING MECHANISMS SHALL BE NOTES: A. SEE DEFINITION IN CHAPTER 2.
FLOOR. LOCATED NO HIGHER THAN 48", & NO LOWER THAN 15", ABOVE THE FINISHED FLOOR MEASURED TO THE CENTER OF THE CORD LENGTH. B. SEE (FIG. 11A-9A)
NOTE:
SHOWER COMPARTMENT FLOOR SURFACES SHALL BE STABLE, FIRM, AND SLIP RESISTANT. THE MAX. SLOPE OF THE GRIP. IF THE REACH IS OVER AN OBSTRUCTION (FOR EXAMPLE, WASHER OR DRYER), OPERATING MECHANISMS SHALL BE THE CORD FROM THE TELEPHONE TO THE HANDSET SHALL BE AT LEAST 29" LONG. ( C.B.C.-1140A.9)
ALL IDEAS, DESIGN ARRANGEMENTS AND PLANS INDICATED OR REPRESENTED BY THIS DRAWING ARE OWNED BY AND THE PROPERTY OF ARK ARCHITECTS, INC. AND WERE CREATED EVOLVED AND DEVELOPED FOR USE ON AND IN CONNECTION WITH THE SPECIFIED PROJECT. NONE OF SUCH IDEAS ARRANGEMENTS OR PLANS SHALL BE USED BY OR DISCLOSED TO ANY PERSON FIRM OR CORPORATION FOR ANY PURPOSE WHATSOEVER WITHOUT THE WRITTEN PERMISSION OF ARK ARCHITECTS, INC.
A R K
1. REFER TO SHEETS A9-1.5 FOR RESIDENTIAL UNIT ACCESSIBILITY REQUIREMENTS. 1. WHEELCHAIR TURNING SPACE.
FLOOR SHALL BE 14" PER FOOT IN ANY DIRECTION. WHEN DRAINS ARE PROVIDED, GRATE OPENINGS SHALL BE 14" MAX. LOCATED WITHIN THE REACH RANGES SPECIFIED IN SECTION 1138.3. CONTROLS & OPERATING MECHANISMS THAT DO
2. ALL INFORMATION IS BASED ON C.B.C. 2019
AND LOCATED FLUSH WITH THE FLOOR SURFACE. (C.B.C.-1127A.5.3.4) NOT SATISFY THESE SPECIFICATIONS ARE ACCEPTABLE, PROVIDED THAT COMPARABLE MECHANISMS, CONTROLS OR TELEPHONE BOOKS. TURNING SPACE OF SUFFICIENT SIZE TO INSCRIBE A CIRCLE WITH A DIAMETER NOT LESS THAN 60" OR A T-SHAPED SPACE
WHEN COMMON USE LAVATORIES ARE PROVIDED FOR RESIDENTS OR GUESTS, AT LEAST ONE, AND NOT LESS THAN 1% OUTLETS THAT PERFORM THE SAME FUNCTIONS ARE PROVIDED WITHIN THE SAME AREA AND ARE ACCESSIBLE. IF TELEPHONE BOOKS ARE PROVIDED, THEY SHALL BE LOCATED IN A POSITION THAT COMPLIES WITH THE REACH SHALL BE PROVIDED WITHIN THE TOILET FACILITY. THE WHEELCHAIR TURNING SPACE SHALL COMPLY WITH SECTION
OF ALL LAVATORIES, SHALL COMPLY WITH THE FOLLOWING: CONTROLS: RANGES IN SECTION 1138A.3.(FIG. 11A-1I, & 1J) . (C.B.C.-1140A.10) 1138A.1.3 OTHER THAN THE DOOR TO THE ACCESSIBLE WATER CLOSET COMPARTMENT, A DOOR, IN ANY POSITION, MAY
CONTROLS, FAUCETS AND SHOWER SPRAY UNITS IN SHOWER COMPARTMENTS SHALL BE OPERABLE WITH ONE HAND, WASHING MACHINES & CLOTHES DRYER. ENCROACH INTO THIS SPACE BY NOT MORE THAN 12". (C.B.C.-1127A.2.1#1)
1. LOCATION. AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE WASHING MACHINES & CLOTHES DRYERS IN ACCESSIBLE COMMON USE LAUNDRY ROOMS SHALL BE FRONT LOADING. SHELF. ARCHITECTS, INC.
LAVATORIES SHALL BE INSTALLED WITH THE CENTERLINE OF THE FIXTURE A MIN. OF 18" HORIZ. FROM AN ADJOINING OPERABLE PARTS SHALL BE 5 LBS. MAX. ALL CONTROLS AND FAUCETS SHALL BE OF A SINGLE-LEVER DESIGN. (C.B.C.-1127A.10 ) PUBLIC PAY TELEPHONES REQUIRED TO ACCOMMODATE A PORTABLE TTY SHALL BE EQUIPPED WITH A SHELF AND 2. CLEAR SPACE AT FIXTURES.
FIXED OR BUILT-IN SEATING, TABLES & COUNTERS:
WALL OR FIXTURE. THE TOP OF THE FIXTURE RIM SHALL BE A MAX. OF 34" ABOVE THE FINISHED FLOOR. (C.B.C.-1127A.5.3.5) AN ELECTRICAL OUTLET WITHIN OR ADJACENT TO THE TELEPHONE ENCLOSURE. THE TELEPHONE HANDSET SHALL DOORS SHALL NOT SWING INTO THE FLOOR SPACE REQUIRED FOR ANY FIXTURE. REQUIRED CLEAR FLOOR SPACE,
(C.B.C.-1127A.12)
BE CAPABLE OF BEING PLACED FLUSH ON THE SURFACE OF THE SHELF. THE SHELF SHALL BE CAPABLE OF CLEARANCE AT FIXTURE AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP. (C.B.C.-1127A.2.1#2)
Faramarz Jabbari, AIA
2. FLOOR SPACE. STANDARD ROLL-IN SHOWER COMPARTMENTS. ACCOMMODATING A TTY AND SHALL HAVE 6" MIN. VERTICAL CLEARANCE ABOVE THE AREA WHERE THE TTY IS TO BE
30" 42" PLACED. (C.B.C.-1140A.11) 3. ACCESSIBLE WATER CLOSET COMPARTMENT.
A CLEAR FLOOR SPACE AT LEAST 30" BY 48' SHALL BE PROVIDED IN FRONT OF ACCESSIBLE LAVATORIES TO ALLOW OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE INSTALLED ON THE BACK WALL OF THE COMPARTMENT
MIN. MIN. ACCESSIBLE WATER CLOSETS COMPARTMENTS SHALL BE 60" WIDE MIN. MEASURED PERPENDICULAR TO THE SIDE WALL,
FORWARD APPROACH. SUCH CLEAR SPACE SHALL ADJOIN OR OVERLAP AN ACCESSIBLE ROUTE OR ANOTHER CLEAR ADJACENT TO THE SEAT WALL, 19" MIN. AND 27" MAX. FROM THE SEAT WALL.
56" DEEP MIN. FOR WALL HUNG WATER CLOSETS AND 59 INCHES DEEP MIN. FOR FLOOR MOUNTED WATER CLOSETS 2240

MAX.
SPACE.

10"
OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48" MEASURED PERPENDICULAR TO REAR WALL (FIG. 11A-9A(c)). (C.B.C.-1127A.2.1#3)
NOTE: Faraday Road
3. KNEE & TOE SPACE. ABOVE THE SHOWER FLOOR, WITH THEIR CENTERLINE AT 39" MIN. AND 41" MAX. ABOVE THE SHOWER FLOOR. ANY
ALL DIMENSIONS WATER CLOSETS FIXTURES LOCATED IN ACCESSIBLE WATER CLOSETS COMPARTMENTS SHALL BE POSITIONED WITH A
A CLEAR AND OBSTRUCTED KNEE AND TOE SPACE, COMPLYING WITH SECTION 1138A.2, SHALL BE PROVIDED 30" X 48"

48"
SHOWN ARE MIN. (a) PARALLEL APPROACH WALL OR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE WATER CLOSET SHALL BE 17" MIN. TO 18"
UNDERNEATH THE LAVATORY, AND SHALL BE CENTERED ON THE FIXTURE. THE FLOOR CLEAR SPACE REQUIRED BY ITEM 2 OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE INSTALLED ON THE BACK WALL MIN. CLR. WIDTH
CLEAR DIMENSIONS MAX. FROM THE SIDE WALL OR PARTITION. Carlsbad, California
SHALL NOT EXTEND INTO THE KNEE & TOE SPACE MORE THAN 19". (FIG. 11A-9D) ADJACENT TO THE SEAT WALL, 19" MIN. AND 27" MAX. FROM THE SEAT WALL. FLR. SPACE
FINISH TO FINISH. OPTIONAL 92008
4. FINISHED FLOOR. OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE LOCATED ABOVE THE GRAB BAR, POST & BASE IN AMBULATORY ACCESSIBLE TOILET COMPARTMENTS SPECIFIED IN ITEM 6 OF THIS SECTION, THE WATER CLOSET SHALL
PLAN Tel: (858) 792-5997
THE FINISHED FLOOR BENEATH THE LAVATORY SHALL BE EXTENDED TO THE WALL. BUT NO HIGHER THAN 48" ABOVE THE SHOWER FLOOR (MEASURED TO THE TOP OF THE MOUNTING BRACKET). BE 17" MIN. AND 19" MAX. FROM THE SIDE WALL OR PARTITION (FIG. 11A-9A (d)).

48" MAX.
TELEPHONES Fax: (858) 792-5858
(C.B.C.-1127A.5.3.5.1)
5. PLUMBING PROTECTION. ACCESSIBLE PATH OF TRAVEL (FIGURE 11A-11B) CLEARANCE AROUND A WATER CLOSET SHALL BE 60" MIN. MEASURED PERPENDICULAR FROM THE SIDE WALL AND 56" MIN.
WATER SUPPLY & DRAIN PIPES UNDER LAVATORIES SHALL BE INSULATED OR OTHERWISE COVERED. (FIG. 11A-9D) MEASURED PERPENDICULAR FROM THE REAR WALL. THE REQUIRED CLEARANCE AROUND THE WATER CLOSET SHALL BE
ALTERNATE ROLL-IN SHOWER COMPARTMENTS: PERMITTED TO OVERLAP THE WATER CLOSET, ASSOCIATED GRAB BARS, DISPENSERS, SANITARY NAPKINS DISPOSAL

24" MAX.

20" MAX.

.
(C.B.C.-1127A.3) OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE INSTALLED ON THE SIDE WALL OF THE COMPARTMENT 30" X 48" UNITS, COAT HOOKS, SHELVES, ACCESSIBLE ROUTES, CLEAR FLOOR SPACE AND CLEARANCES REQUIRED AT OTHER 09/12/2022
ADJACENT TO THE SEAT WALL, 19" MIN. AND 27" MAX. FROM THE SEAT WALL. MIN. CLEAR FIXTURES, AND THE THE TURNING SPACE. NO OTHER FIXTURES OR OBSTRUCTIONS SHALL BE LOCATED WITHIN THE
8" A SECOND CITY SUBMITTAL
AREA REQUIRED WATER CLOSET CLEARANCE.
25" MAX. 17"-25"

MIN.
MIN.

30"
OPERABLE PARTS OF CONTROLS AND FAUCETS SHALL BE LOCATED ABOVE THE GRAB BAR, BUT NO HIGHER THAN 48" (b) FORWARD APPROACH ELEVATION 10/26/2022
ABOVE THE SHOWER FLOOR, WITH THEIR CENTERLINE AT 39" MIN. AND 41" MAX. ABOVE THE SHOWER FLOOR. A MIN. 48" DEEP AND 60" WIDE CLEAR MANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET IF THE B THIRD CITY SUBMITTAL
COMPARTMENT HAS AN END-OPENING DOOR (FACING THE WATER CLOSET). A MIN. 60" DEEP AND 60" WIDE CLEAR
OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE INSTALLED ON THE FOLLOWING PLAN
MIN.

MIN.
MANEUVERING SPACE SHALL BE PROVIDED IN A COMPARTMENT WITH THE DOOR LOCATED AT THE SIDE (FIG. 11A-9A). 3

MIN.
30"

30"
----
27" MIN.

19"
LOCATIONS: (C.B.C.-1127A.2.1#3)
1. ON THE SIDE OF THE WALL OF THE COMPARTMENT ADJACENT TO THE SEAT WALL, 17" MIN. AND 19" MAX. FROM THE MINIMUM CLEARANCES FOR 4. GRAB BARS.
TOILET / BATHING SIGNS
MIN.

MIN.
SEAT WALL; OR SEATING & TABLE (FIG. 11A-1K) GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSET TO THE WATER CLOSET AND ON THE REAR WALL.GRAB 4 ----
9"

9"
(C.B.C.-1127A.7 & 1143A)
11"

MIN.
2. ON THE BACK WALL OPPOSITE THE SEAT, 15" MAX., LEFT OR RIGHT, OF THE CENTERLINE OF THE SEAT. BARS SHALL COMPLY WITH THIS SECTION AND SECTION 1127A.4.

30"
MIN. 6" MAX. GENERAL. 5 ----
OPERABLE PARTS OF THE SHOWER SPRAY UNIT, INCLUDING THE HANDLE, SHALL BE LOCATED ABOVE THE GRAB BAR, ALL ACCESSIBLE TOILET& BATHING FACILITIES SHALL BE IDENTIFIED BY THE "INTERNATIONAL SYMBOL OF THE SIDE WALL GRAB BAR SHALL BE 42" LONG MIN., LOCATED 12" MAX. FROM THE REAR WALL AND EXTENDED 54" MIN.
(a) KNEE SPACE - GENERAL REQUIREMENTS (b) TOE SPACE - GENERAL REQUIREMENTS BUT NO HIGHER THAN 48" ABOVE THE SHOWER FLOOR. (C.B.C.-1127A.5.3.5.2) ACCESSIBILITY." SIGNS NEED NOT BE PROVIDED FOR FACILITIES WITHIN A DWELLING UNIT OR GUESTROOM. FROM THE REAR WALL. THE FRONT END OF THE SIDE GRAB BAR SHALL BE POSITIONED 24" MIN. IN FRONT OF THE WATER
CLOSET. 6 ----
30" (C.B.C.-1127A.7.1)
MIN. IDENTIFICATION SYMBOLS.
17" HAND-HELD SPRAYER UNIT: DOORWAYS LEADING TO SANITARY FACILITIES ( TOILET OR BATHING ROOM) SHALL BE IDENTIFIED BY A GEOMETRIC THE REAR WALL GRAB BAR SHALL BE 36" LONG MIN. AND EXTEND FROM THE CENTERLINE OF THE WATER CLOSET 12" 7
MIN. ----
A FLEXIBLE HAND-HELD SHOWER SPRAY UNIT WITH A HOSE AT LEAST 59" LONG THAT CAN BE USED BOTH AS A FIXED 48" 19" SYMBOL IN COMPLIANCE WITH THIS SECTION. GEOMETRIC SYMBOLS SHALL BE CENTERED HORIZONTALLY ON THE MIN. ON ONE SIDE AND 24" MIN. ON THE OTHER SIDE.
SHOWER HEAD AND AS A HAND-HELD SHOWER SHALL BE PROVIDED (C.B.C.-1127A.5.3.6) MIN. MIN. DOOR AT THE HEIGHT OF 58" MIN. & 60" MAX. ABOVE THE FINISH FLOOR MEASURED TO THE CENTERED OF THE
MIN.

K-T13140-3B
PINSTRIPE
FAUCETS
BRASS
18"

LAVATORY)
----
(TO RIM OF
CLEAR SYMBOL. WHEN A DOOR IS PROVIDED,THE SYMBOL SHALL BE MOUNTED WITHIN 1" OF THE VERTICAL CENTERLINE OF EXCEPTIONS:
MIN.

SHOWER COMPARTMENT SEATS: MINIMUM SEATING: WHERE FIXED OR BUILT-IN SEATING, TABLES OR COUNTERS ARE PROVIDED FOR RESIDENTS OR 1. THE REAR GRAB BAR SHALL BE PERMITTED TO BE 24" LONG MIN., CENTERED ON THE WATER CLOSET, WHEN WALL
30"

MAX.*
FLOOR CL THE DOOR. DIRECTIONAL SIGNS INDICATING THE LOCATION OF THE NEAREST ACCESSIBLE TOILET OR BATHING
VITREOUS CHINA
PENNINGTON
LAVATORY
K-2196-8

34"
MIN.

A SEAT IN A STANDARD ROLL-IN SHOWER COMPARTMENT SHALL BE A FOLDING TYPE, INSTALLED ON THE SIDE WALL GUESTS, 5%, BUT NOT LESS THAN ONE, SHALL BE ACCESSIBLE AS PROVIDED IN THIS SECTION. (C.B.C.-1127A.12.1) SPACE DOES NOT PERMIT A LENGTH OF 36" MIN. DUE TO THE LOCATION OF A RECESSED FIXTURE ADJACENT TO THE 9
29"

SPACE ROOMS SHALL BE PROVIDED. SUCH DIRECTIONAL SIGNS SHALL COMPLY WITH SECTION 1143.5 AND SHALL INCLUDE
MIN.

----
27"

ADJACENT TO THE CONTROLS. THE SEAT SHALL EXTEND FROM THE BACK WALL TO THE POINT WITH IN 3" OF THE THE INTERNATIONAL SYMBOL OF ACCESSIBILITY. EDGES OF ACCESSIBILITY SIGNAGE SHALL BE ROUNDED, WATER CLOSET.
MIN.

CLEAR FLOOR SPACE: WHEN SEATING SPACES FOR PERSONS IN WHEELCHAIRS ARE PROVIDED AT FIXED TABLES OR
9"

19" COMPARTMENT ENTRY. A SEAT IN AN ALTERNATE ROLL-IN TYPE SHOWER COMPARTMENT SHALL BE A FOLDING TYPE CHAMFERED OR EASED CORNERS SHALL HAVE A MINIMUM RADIUS OF 1/8". SEE SECTION 1143A FOR ADDITIONAL 2. WHEN THE ENFORCING AGENCY REQUIRES FLUSH VALVES TO BE LOCATED IN A POSITION THAT CONFLICTS WITH
PLAN VIEW SIDE ELEVATION INSTALLED ON A FRONT WALL OPPOSITE THE BACK WALL & SHALL EXTEND FROM THE ADJACENT SIDE WALL TO A POINT COUNTERS, CLEAR FLOOR SPACE COMPLYING WITH SECTION 1138A.1.4 POSITIONED FOR A FORWARD APPROACH SHALL SIGNAGE REQUIREMENTS APPLICABLE TO SANITARY FACILITIES. (C.B.C.-1127A.7.2) THE LOCATION OF THE REAR GRAB BAR, THE THE REAR GRAB BAR SHALL BE PERMITTED TO BE SPLIT OR SHIFTED ARIZONA # : 27259
MAX. 8" 6" TOE CLEARANCE*
48" WITH-IN 3" OF THE COMPARTMENT ENTRY. SHOWER COMPARTMENT SEATS SHALL COMPLY WITH SECTION 1127A.4.4 BE PROVIDED. SUCH CLEAR FLOOR SPACE SHALL NOT OVERLAP THE REQUIRED KNEE AND TOE SPACE BY MORE THAN 19". TO THE OPEN SIDE OF THE TOILET AREA. (C.B.C.-1127A.2.1#4)
MIN. MAX. CALIFORNIA # : C15528
MIN. * NOTE: IF A MIN. 9" HEIGHT OF TOE SHALL BE LOCATED 27" OF THE SHOWER CONTROLS. THE TOP OF THE SEATS SHALL BE 17" MIN. & 19" MAX. ABOVE THE (FIG. 11A-1K) (C.B.C.-1127A.12.2) VISUAL CHARACTERS (C.B.C.-1143A.5)
17"MIN. BATHROOM FINISH FLOOR WHEN FOLDED, THE SEAT SHALL NOT EXTEND MORE THAN 6" FROM THE MOUNTING WALL. 5. COMPARTMENT DOORS. COLORADO # : 304356
CLEARANCE IS PROVIDED, A MAX. OF 6"
OF THE 48" OF CLEAR FLOOR SPACE (FIG. 11A-9H, 9I & 9J) (C.B.C.-1127A.5.3.7) KNEE AND TOE SPACE: WHEN SEATING FOR PERSONS IN WHEELCHAIRS IS PROVIDED AT FIXED TABLES OR COUNTERS, 1.FINISH & CONTRAST. COMPARTMENT DOORS SHALL COMPLY WITH SECTION 1126A AND THE FOLLOWING:
(c) KNEE AND TOE SPACE FOR LAVORATORIES 25"MAX. OREGON # : 5318
REQUIRED AT THE FIXTURE MAY EXTEND KNEE AND TOE SPACE COMPLYING WITH SECTION 1138A.2 SHALL BE PROVIDED. (FIGURE 11A-1K) CHARACTERS & THEIR BACKGROUND SHALL HAVE A NON GLARE FINISH. AND SHALL CONTRAST WITH THEIR
INTO THE TOE SPACE. GRAB BARS: (C.B.C.-1127A.12.3 ) BACKGROUND. THE WATER CLOSET COMPARTMENT SHALL BE EQUIPPED WITH A DOOR THAT HAS AN AUTOMATIC-CLOSING DEVICE, NEVADA # : 2838
ACCESSIBLE SHOWER COMPARTMENTS SHALL BE PROVIDED WITH GRAB BARS, INSTALLED IN ACCORDANCE WITH AND SHALL HAVE A CLEAR, UNOBSTRUCTED OPENING WIDTH OF 32" WHEN LOCATED AT THE END AND 34" WHEN LOCATED
KNEE CLEARANCE HEIGHT OF WORK SURFACES: THE TOPS OF TABLES AND COUNTERS SHALL BE 28" TO 34" FROM THE FINISH FLOOR. TEXAS # : 16533
SECTION 1127A.5.3.8.1 OR SECTION 1127A.5.3.8.2. GRAB BARS SHALL ALSO COMPLY WITH SECTION 1127A.4. 4. CHARACTER HEIGHT: VISUAL CHARACTERS SHALL BE SIZED IN ACCORDANCE WITH TABLE 1143A.5. VIEWING AT THE SIDE WITH THE DOOR POSITIONED AT AN ANGLE OF 90° FROM ITS CLOSED POSITION.
(FIG. 11A-9D)
(FIG. 11A-9H & 9I) (C.B.C.-1127A.5.3.8) DISTANCE SHALL BE MEASURED AS THE HORIZONTAL DISTANCE BETWEEN THE CHARACTER AND AN OBSTRUCTION UTAH # : 7288093-0301
EXCEPTION: WHEN FOOD OR DRINK IS SERVED FOR CONSUMPTION AT A COUNTER EXCEEDING 34" IN HEIGHT, ONLY A PREVENTING FURTHER APPROACH TOWARDS THE SIGN. CHARACTER HEIGHT SHALL BE BASED ON THE UPPERCASE 5.2. WHEN STANDARD COMPARTMENT DOORS ARE USED, WITH MIN. 9" CLEARANCE FOR FOOTRESTS UNDERNEATH & THE
PORTION OF THE MAIN COUNTER, 60" MIN. IN LENGTH, SHALL BE PROVIDED IN COMPLIANCE WITH THIS SECTION. WASHINGTON # : 8895
SOAP DISH: LETTER "I". SELF-CLOSING DEVICE, CLEARANCE AT THE STRIKE EDGE AS SPECIFIED IN SECTION 1126A.3.2 IS NOT REQUIRED.
GRAB BARS, TUB & SHOWER SEATS FASTENERS & MOUNTING DEVICES WHEN A SOAP DISH IS PROVIDED, IT SHALL BE LOCATED ON THE CONTROL WALL AT A MAX. HEIGHT OF 40" ABOVE THE (C.B.C.-1127A.12.4)
(C.B.C. - 1127A.4) SHOWER FLOOR, AND WITHIN THE REACH LIMITS FROM THE SEAT. RAISED CHARACTERS AND PICTORIALS SYMBOL SIGNS (C.B.C.-1143A.6) 5.3. THE INSIDE AND OUTSIDE OF THE COMPARTMENT DOOR SHALL BE EQUIPPED WITH A LOOP OR U-SHAPED HANDLE ADDRESS:
(C.B.C.-1127A.5.3.9) IMMEDIATELY BELOW THE LATCH.
ACCESSIBLE DRINKING FOUNTAINS: 1 1590 BARTLETT LN
CHARACTER TYPE: RAISED CHARACTERS ON SIGNS SHALL BE 32" MIN. ABOVE THEIR BACKGROUND.

1548, 1554, 1560, 1566, 1572, 1578, 1584, & 1590 Bartlett
GRAB BARS LOCATION.
OPEN SHOWERS. (C.B.C.-1139A) 5.4. EXCEPT FOR DOOR-OPENING WIDTHS & DOOR SWINGS, A CLEAR, UNOBSTRUCTED ACCESS OF NOT LESS THAN 44" SACRAMENTO, CA 95815
GRAB BARS SHALL BE INSTALLED IN A HORIZONTAL POSITION, 33" MIN. AND 36" MAX ABOVE THE FINISHED FLOOR,
MEASURED TO THE TOP OF GRIPPING SURFACE. EXCEPTION: THE HEIGHT OF THE LOWER GRAB BAR ON THE BACK WALL WHERE NO SEPARATE SHOWER COMPARTMENTS ARE PROVIDED, THE SHOWER FOR PERSONS WITH DISABILITIES SHALL CHARACTER HEIGHT: CHARACTER HEIGHT MEASURED VERTICALLY FROM THE BASELINE OF THE CHARACTER SHALL SHALL BE PROVIDED TO WATER CLOSET COMPARTMENT DESIGNED FOR USE BY PERSONS WITH DISABILITIES, & THE
OF A BATHTUB SHALL COMPLY WITH SECTION 1127A.5.2. (FIG. 11A-9A & 11A-9B) BE LOCATED IN A CORNER WITH L-SHAPED GRAB BARS EXTENDING ALONG TWO ADJACENT WALLS WITH A FOLDING SEAT GENERAL. BE A MIN. OF 5 8" & A MAX. 2" BASED ON THE HEIGHT OF THE UPPERCASE LETTER "I". SPACE IMMEDIATELY IN FRONT OF A WATER CLOSET COMPARTMENT SHALL NOT BE LESS THAN 48" AS MEASURED AT
ADJACENT TO THE SHOWER CONTROLS, (FIG. 11A-9H, 9I, 9J & 9K). DRINKING FOUNTAINS & WATER COOLERS IN COMMON USE AREAS AND/ OR SITES SHALL COMPLY WITH THIS RIGHT ANGLES TO COMPARTMENT DOOR IN ITS CLOSED POSITION.
DIAMETER OR WIDTH (C.B.C.-1127A.5.3.10) SECTION. A SIDE APPROACH DRINKING FOUNTAIN IS NOT ACCEPTABLE. (C.B.C.-1139A.1) LOCATION: WHEN A TACTILE SIGN IS PROVIDED AT A DOOR, THE SIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT
THE LATCH SIDE. WHEN TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN SHALL BE 5.5. DOORS SHALL BE LOCATED IN THE FRONT OR IN THE SIDE WALL OR PARTITION FARTHEST FROM THE WATER
1. CIRCULAR CROSS SECTION. SHALL HAVE AN OUTSIDE DIAMETER OF 1 14" MIN. AND 2" MAX.
MULTIPLE SHOWERS. ACCESSIBLE ROUTE. LOCATED ON THE INACTIVE LEAF. WHEN TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH TWO ACTIVE LEAFS, CLOSET. LOCATED IN THE FRONT PARTITION THE DOOR OPENING SHALL BE 4" MAX. FROM THE SIDE WALL. LOCATED IN
2. NONCIRCULAR CROSS SECTION. SHALL HAVE DIMENSION OF 2" MAX. THE PERIMETER DIMENSION SHALL BE 4" MIN
AND 4.8" MAX. WHERE TWO OR MORE ACCESSIBLE SHOWERS ARE PROVIDED WITH-IN THE SAME FUNCTIONAL AREA, THERE SHALL BE DRINKING FOUNTAINS & WATER COOLERS SHALL BE ON AN ACCESSIBLE ROUTE. (C.B.C.-1139A.2) THE SIGN SHALL BE LOCATED TO THE RIGHT OF THE RIGHT HAND DOOR. WHEN THERE IS NO WALL SPACE AT THE THE SIDE WALL, THE DOOR OPENING SHALL BE 4" FROM THE FRONT WALL OR PARTITION. (C.B.C.-1127A.2.1#5)
3. L-SHAPED OR U-SHAPED GRAB SHALL BE PERMITTED. (FIG. 11A-9C) AT LEAST ONE SHOWER CONSTRUCTED OPPOSITE HAND FROM THE OTHER OR OTHERS (I.E., ONE LEFT-HAND CONTROL LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF DOUBLE DOORS, SIGNS SHALL BE LOCATED ON THE
VERSUS RIGHT-HAND CONTROLS). 6. AMBULATORY ACCESSIBLE COMPARTMENTS.
(C.B.C.-1127A.4.3) DEPTH. NEAREST ADJACENT WALL. SIGNS CONTAINING TACTILE CHARACTERS SHALL BE LOCATED SO THAT A CLEAR FLOOR
(C.B.C.-1127A.5.3.11) WHEN SIX OR MORE TOILET COMPARTMENTS ARE PROVIDED WITHIN A MULTIPLE-ACCOMMODATION TOILET ROOM, OR
2" DRINKING FOUNTAINS SHALL BE A MIN. OF 18" AND A MAX. OF 19" IN DEPTH. (C.B.C.-1139A.3) SPACE OF 18" MIN. X 18" MIN. CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF ANY
2" WHEN THE COMBINATION OF URINALS AND WATER CLOSETS TOTAL SIX OR MORE FIXTURES, AT LEAST ONE
MAX. MAX. DOOR SWING BETWEEN THE CLOSED POSITION AND 45° OPEN POSITION. WHEN PERMANENT IDENTIFICATION
1 1/4" TO 2" LOCKERS. COMPARTMENT SHALL COMPLY WITH SECTION 1127A.2.1, ITEMS 2 & 3. AT LEAST ONE ADDITIONAL AMBULATORY
CLEAR FLOOR SPACE. SIGNAGE IS PROVIDED FOR ROOMS AND SPACES THEY SHALL BE LOCATED ON THE APPROACH SIDE OF THE DOOR
NOMINAL WHERE LOCKERS ARE PROVIDED FOR RESIDENTS OR GUESTS, AT LEAST ONE LOCKER & NOT LESS THAN 1% OF ALL COMPARTMENT SHALL HAVE A DEPTH OF 60" MIN. AND A WIDTH OF 35" MIN. & 37" MAX.
DRINKING FOUNTAINS SHALL BE PROVIDED WITH 30" BY 48" CLEAR FLOOR SPACE, CENTERED ON THE UNIT. THE AS ONE ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALL BE LOCATED ON THE APPROACH SIDE OF
DIAMETER LOCKERS SHALL BE ACCESSIBLE TO PERSONS WITH DISABILITIES. AN ACCESSIBLE ROUTE NOT LESS THAN 36" IN CLEAR THE DOOR AS ONE EXITS THE ROOM OR SPACE. (C.B.C.-1143A.6 #8)
(a) SECTION THROUGH .. (b) NON-CIRCULAR CLEAR FLOOR SPACE SHALL BE POSITIONED FOR A FORWARD APPROACH. (C.B.C.-1139A.4) THE AMBULATORY ACCESSIBLE COMPARTMENT SHALL HAVE A SELF CLOSING DOOR, WHICH SHALL NOT SWING INTO THE
WIDTH SHALL BE PROVIDED TO THESE LOCKERS. (SEE SECTION 1138A FOR OTHER REQUIREMENTS)

D E V E L O P M E N T
TYPICAL CIRCULAR CROSS SECTIONS MIN. REQUIRED COMPARTMENT AREA. GRAB BARS, COMPLYING WITH SECTIONS 1127A.4.2, 1127A.4.3, 1127A.4.4 & 1127A.4.5
GRAB BAR (C.B.C.-1127A.6) 60" MIN. KNEE AND TOE SPACE. HEIGHT: WITH RAISED CHARACTERS SHALL BE LOCATED 48" MIN. ABOVE FINISH FLOOR, MEASURED FROM
1 12" SHALL BE INSTALLED ON EACH COMPARTMENT SIDE WALL (FIG. 11A-9A(d)).
WALL INSIDE FACE OF FINISH DRINKING FOUNTAINS SHALL BE PROVIDED WITH A CLEAR AND UNOBSTRUCTED KNEE AND TOE SPACE. THE BASELINE OF THE LOWEST BRAILLE CELLS AND 60" MAX. ABOVE THE FINISH FLOOR, MEASURED FROM THE
(C.B.C.-1127A.2.1#6)
4"-4.8" PERIMETER LOCATIONS OF (FIGURE 11A-9D) (C.B.C.-1139A.4.1) BASELINE OF THE HIGHEST LINE OF RAISED CHARACTERS.
GRAB BAR SECTION SINGLE LEVER 19"-27"
(FIG. 11B-609.2.2) CONTROLS SINGLE-ACCOMMODATION TOILET FACILITIES, (1127A.2.2)
(FIG. 11A-9C) CONTROLS MAX. PICTORIAL SYMBOL SIGNS (PICTOGRAMS): PICTORIAL SYMBOL SIGNS (PICTOGRAMS) SHALL BE ACCOMPANIED BY A
SPOUT LOCATION. SHALL COMPLY WITH THE FOLLOWING:
SPOUT LOCATION SHALL BE LOCATED 15" MIN. FROM THE VERTICAL SUPPORT AND 5" MAX. FROM THE FRONT EDGE TEXT DESCRIPTION LOCATED DIRECTLY BELOW THE PICTOGRAM FIELD. THE OUTSIDE DIMENSION OF THE

INSIDE FACE
TOP OF
FOLDING SEAT OF THE DRINKING FOUNTAIN, INCLUDING BUMPERS. SPOUT OUTLETS SHALL BE 36" MAX. ABOVE FINISH FLOOR. PICTOGRAM FIELD SHALL BE A MIN. OF 6" IN HEIGHT

30" MIN.
NOTE: SEE FIGURES 11A-9A AND 11A-9B.

OF FINISH
MOUNTING
3" MAX. FROM (C.B.C.-1139A.5)
BATHING FACILITIES: BRACKET
COMPARTMENT BRAILLE (C.B.C.-1143A.7) 1. WHEELCHAIR CLEARANCE.
(C.B.C. - 1127A.5)
ENTRY WATER FLOW. THERE SHALL BE SUFFICIENT SPACE IN THE TOILET ROOM FOR A WHEELCHAIR MEASURING 30" WIDE BY 48" LONG TO
17"-19"

GATEWAY
19" THE SPOUT SHALL PROVIDE A FLOW OF WATER AT LEAST 4" HIGH TO ALLOW THE INSERTION OF A CUP OR GLASS POSITION: BRAILLE SHALL BE POSITIONED BELOW THE CORRESPONDING TEXT IN A HORIZONTAL FORMAT, FLUSH ENTER THE ROOM & PERMIT THE DOOR TO CLOSE. THERE SHALL BE IN THE ROOM A CLEAR FLOOR SPACE OF AT LEAST 60"
GENERAL.

VILLAGE-PHASE 2
MIN. LEFT OR CENTERED. IF TEXT IS MULTI-LINED, BRAILLE SHALL BE PLACED BELOW THE ENTIRE TEXT. BRAILLE SHALL BE
MAX.

1
2 " MAX. BEVELED
UNDER THE FLOW OF WATER. THE ANGLE OF THE WATER STREAM SHALL BE MEASURED HORIZONTALLY RELATIVE IN DIAMETER OR A T-SHAPED SPACE COMPLYING WITH SECTION 1138A.1.3. REQUIRED CLEAR FLOOR SPACE, CLEARANCE
39"-41"

30" MIN.
48"

WHEN COMMON USE BATHING FACILITIES ARE PROVIDED FOR RESIDENTS OR GUESTS, INCLUDING SHOWERS, BATHTUBS
33"-36"

THRESHOLD TO THE FRONT FACE OF THE UNIT.WHEN SPOUTS ARE LOCATED LESS THAN 3" FROM THE FRONT OF THE UNIT, THE SEPARATED 3 8" MIN. AND 12" MAX. FROM ANY OTHER TACTILE CHARACTERS AND 3 8" MIN. FROM RAISED BORDERS AND AT FIXTURE AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP.
OR LOCKERS, AT LEAST ONE OF EACH TYPE OF FIXTURE IN EACH FACILITY, AND NOT LESS THAN 1% OF ALL FIXTURES,
ANGLE OF THE WATER STREAM SHALL BE 30° MAX. WHEN SPOUTS ARE LOCATED BETWEEN 3" & 5" MAX. FROM THE DECORATIVE ELEMENTS. (C.B.C.-1143A.7.2)
SHALL COMPLY WITH THIS SECTION. FOLDING
FRONT OF THE UNIT, THE ANGLE OF THE WATER STREAM SHALL BE 15° MAX. (C.B.C.-1139A.6) 2. ENCROACHMENT OF DOORS.
SEAT
BATHTUB SHALL COMPLY WITH THE FOLLOWING: PLAN DOORS SHALL NOT ENCROACH INTO THE CLEAR FLOOR SPACE SPECIFIED IN ITEM 1 OF THIS SECTION BY MORE THAN 12",
60" MIN.

APARTMENTS
CONTROLS AND OPERATING MECHANISMS.
THE FLOW OF THE WATER SHALL BE ACTIVATED BY MANUALLY OR ELECTRONICALLY OPERATED CONTROLS. THE 3. ACCESSIBLE WATER CLOSET.
FLOOR SPACE. FOR CLEAR FLOOR SPACE SEE (FIG. 11A-9E). (a) 60" X 30" ROLL-IN SHOWER MANUALLY OPERATED CONTROLS SHALL BE FRONT MOUNTED OR SIDE MOUNTED, LOCATED WITHIN 6" OF THE A WATER CLOSET FIXTURE LOCATED IN A SINGLE-ACCOMMODATION TOILET FACILITY SHALL BE POSITIONED WITH A WALL

12

SACRAMENTO, CALIFORNIA
"
FRONT EDGE OF THE FOUNTAIN. THE FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5LBS. OR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE WATER CLOSET SHALL BE 17" MIN. TO 18" MAX.

12"

12"
SEAT. FOR AN IN-TUB SEAT OR A SEAT AT THE HEAD END OF THE TUB SEE (FIG. 11A-9E & 9F).
(C.B.C.-1139A.7) FROM THE SIDE WALL OR PARTITION. (1127A.2.2 #1,2,&3)
SEATS SHALL NOT SLIP DURING USE.
CONTROLS & HANDHELD SHOWER HOSE
42" MIN. 19"-27" FROM THE FOLDING SEAT. THE LOCATION. WOMEN MEN UNISEX 4. GRAB BARS.
GRAB BARS. FOR GRAB BARS SEE (FIG. 11A-9F & 9F).
INSIDE FACE HANDHELD SHOWERHEAD SHALL HAVE A DRINKING FOUNTAINS SHALL BE LOCATED COMPLETELY WITHIN ALCOVES, BETWEEN WING WALLS, OR OTHERWISE GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSET TO THE WATER CLOSET AND ON THE REAR WALL.GRAB
OF FINISH DIVERTER FROM THE FIXED SHOWERHEAD POSITIONED SO AS NOT TO ENCROACH INTO PEDESTRIAN WAYS. THE ALCOVE OR OTHERWISE PROTECTED AREA IN BARS SHALL COMPLY WITH THIS SECTION AND SECTION 1127A.4. (1127A.2.2 #4)
CONTROLS. FOR FAUCETS & OTHER CONTROLS SEE (FIG. 11A-9F). WALL MOUNTED IDENTIFICATION SYMBOLS
ON THE OPPOSITE WALL WHICH THE DRINKING FOUNTAIN IS LOCATED SHALL NOT BE LESS THAN 32" IN WIDTH AND 18" IN DEPTH. WHEN THE
19"-27" SIGNAGE TO BE (C.B.C.-1127A.7.2)
DEPTH OF THE PROTECTED AREA WHERE THE DRINKING FOUNTAIN IS LOCATED EXCEEDS 24", ADDITIONAL THE SIDE WALL GRAB BAR SHALL BE 42" LONG MIN., LOCATED 12" MAX. FROM THE REAR WALL AND EXTENDED 54" MIN.
SHOWER SPRAY UNIT. A SHOWER SPRAY UNIT WITH A HOSE AT LEAST 59" LONG THAT CAN BE USED BOTH AS A FIXED LOCATED ON LATCH
SHOWER HEAD & AS A HAND-HELD SHOWER SHALL BE PROVIDED. MANEUVERING CLEARANCE SHALL BE PROVIDED IN ACCORDANCE WITH SECTION 1138A.1.4.2 AND (FIGURE 11A-1H) . FROM THE REAR WALL. THE FRONT END OF THE SIDE GRAB BAR SHALL BE POSITIONED 24" MIN. IN FRONT OF THE WATER
SIDE DOOR, CLEAR OF
STANDARD FIXED SHOWERHEAD CLOSET.
INSIDE FACE

DOOR SWING.
OF FINISH

LOCATED ON OPPOSITE WALL WHEN PROVIDED, WING WALLS SHALL PROJECT OUT FROM THE SUPPORTING WALL AT LEAST AS FAR AS THE
4'-0" MIN.

BATHTUB ENCLOSURES. WHEN PROVIDED, ENCLOSURES FOR BATHTUBS SHALL NOT OBSTRUCT, CONTROLS FACETS DOOR
MOUNT AT 60" TO
PLAN DRINKING FOUNTAIN TO WITHIN 6" VERTICALLY FROM THE FINISH FLOOR. MOUNTED THE REAR WALL GRAB BAR SHALL BE 36" LONG MIN. AND EXTEND FROM THE CENTERLINE OF THE WATER CLOSET 12"
SHOWER & SPRY UNITS, OR OBSTRUCT TRANSFER FROM WHEELCHAIRS ON TO BATHTUB SEATS OR INTO BATHTUBS. CENTERLINE OF SIGN
HALL NOT OBSTRUCT CONTROLS OR TRANSFER FROM WHEELCHAIRS ONTO BATHTUB SEATS OR INTO TUBS. SIGNAGE MIN. ON ONE SIDE AND 24" MIN. ON THE OTHER SIDE.
SEAT EXTENSION FOR FROM FLOOR
ENCLOSURES ON BATHTUBS SHALL NOT HAVE TRACKS INSTALLED ON THE RIM ON THE OPEN FACE OF THE BATHTUB. PROTRUDING OBJECTS LOCATED IN ALCOVES OR OTHERWISE POSITIONED SO AS TO LIMIT ENCROACHMENT INTO
SHOWER STALLS OVER (C.B.C.- 1143A.6 #8)
PEDESTRIAN WAYS ARE PERMITTED TO PROJECT 4" INTO WALKS, HALLS, CORRIDORS, PASSAGEWAYS OR AISLES. EXCEPTIONS:
(C.B.C.-1127A.6) 36" DEEP
ROLL-IN SHOWER (FIGURE 11A-11A) (C.B.C.-1139A.8) 1. THE REAR GRAB BAR SHALL BE PERMITTED TO BE 24" LONG MIN., CENTERED ON THE WATER CLOSET, WHEN WALL
(FIG. 11A-9H) SPACE DOES NOT PERMIT A LENGTH OF 36" MIN. DUE TO THE LOCATION OF A RECESSED FIXTURE ADJACENT TO THE
15"-16" 15"-16" 15" MIN. 1
2' MAX. BEVELED UPPERCASE WATER CLOSET.
(b) 42" X 48" ROLL-IN SHOWER

D E B A R T O L O
BACK WALL BACK WALL BACK WALL THRESHOLD MEN
2. WHEN THE ENFORCING AGENCY REQUIRES FLUSH VALVES TO BE LOCATED IN A POSITION THAT CONFLICTS WITH
5"MAX. 18"-19" LETTERING MEN
-19"{

THE LOCATION OF THE REAR GRAB BAR, THE THE REAR GRAB BAR SHALL BE PERMITTED TO BE SPLIT OR SHIFTED TO
RAISED 132"

18"
END WALL

END WALL

END WALL
CONTROL

18"MIN.
CONTROL

CONTROL
HEAD END

HEAD END

HEAD END

" MAX.

5
18"MIN. THE OPEN SIDE OF THE TOILET AREA. AB BAR, THE THE REAR GRAB BAR SHALL BE PERMITTED TO BE SPLIT OR SHIFTED
SEAT

5"MAX. (C.B.C.-
SEAT

SEAT

18"-1
WALL

WALL

WALL

9"{
TO THE OPEN SIDE OF THE TOILET AREA. (1127A.2.2 #4)

18"
-19"{

1143A.6, #1)

5
" MAX.

6" 6" 6" 5 5. ACCESSIBLE ROUTE.

8"
MIN.
MIN. MIN. MIN. ALL DOORS, FIXTURES AND CONTROLS SHALL BE ON AN ACCESSIBLE ROUTE. THE MIN. CLEAR WIDTH OF AN ACCESSIBLE
2" MAX.
CLEAR BACK WALL BACK WALL ROUTE SHALL BE 36" EXCEPT AT DOORS (SEE SECTION 1126A). IF A PERSON IN A WHEELCHAIR MUST MAKE A TURN
MAX.

MAX.

CLEAR CLEAR (C.B.C.-

5'-0"
MIN.

MIN.

6"

6"

AROUND AN OBSTRUCTION, THE MIN. CLEAR WIDTH OF THE ACCESSIBLE ROUTE SHALL BE AS SPECIFIED IN SECTION
30"

30"

FLOOR
48" MIN.

FLOOR FLOOR 1143A.6, #2)

SIDE WALL

SIDE WALL

1138A.1.5.
SIDE WALL

SIDE WALL

SPACE SPACE SPACE SHOWER SEATS (C.B.C.-1127A.2.2 #5) This set of plans and specifications must be
MEN

.
AND GRAB BARS (a) GRAB BARS kept on the job at all times and it is unlawful to

ARDEN
LENGTH OF BATHTUB LENGTH OF BATHTUB 12"MIN (FIG. 11A-9I) make any changes or alterations from the
" MAX.
5

27" MIN.

same without written permission from the

27" MIN.
36" MAX.

36" MAX.
5
" MAX.

LENGTH OF BATHTUB FRONT FRONT 6"MAX. 60" MIN. Building Inspection Division.
WALL WALL (*) 36" MIN. IF WING CORRESPONDING MOUNTING LOCATION & HEIGHT.
6"MAX. FLUSH The approval of this plan and specification
WALL DEPTH IS >24" GRADE II BRAILLE (C.B.C.-1143A.6) ACTIVATOR 17"-18" 18" SHALL NOT be held to permit or approve the
(a) REMOVABLE SEAT IN TUB - (b) REMOVABLE SEAT IN TUB - (b) PERMANENT SEAT IN TUB - (FIG. 11B-3A) (C.B.C.- 1143A.7)

.XAM "6
ALTERNATE ROLL-IN SHOWER STANDARD ROLL-IN SHOWER ON WIDE SIDE MIN. violation of any City Ordinance or State Law.
FRONT APPROACH SIDE APPROACH FRONT APPROACH
(FIG. 11B-608.3.3) (FIG. 11B-608.3.2)

MAX.
22"-23" (b) SINGLE-ACCOMMODATION

12"

.
15" MIN.

IN
TOILET FACILITY

" M
VITREOUS CHINA
PENNINGTON
K-T13140-3B
LAVATORY
PINSTRIPE
FAUCETS
K-2196-8
BRASS
BACK WALL

60
) (*)
. (*

54"MIN.
. (C.B.C.-1127A)
R LR
END WALL

CL
CONTROL

HEAD END

SEAT SEAT
N. .C
1 12" MAX.

1 12" MAX.
SEAT

MI IN
WALL

(b) SHOWER SEATS NOTE: FOR PUBLIC USE FACILITIES.

(a) ALCOVE
32
" (b) NON-ALCOVE WING "M
32 (SEE CHAPTER 11B - C.B.C. 2016)

48" MIN. CLR.

1 1

24"
INDICATES DIRECTION 2 2" MAX. 2 2" MAX. INSTALLATION WALL INSTALLATION
OF APPROACH GENERAL.
WHEN PROVIDED, COMMON USE AREAS & FACILITIES IN COVERED MULTIFAMILY HOUSING DEVELOPMENTS SHALL BE
(d) PERMANENT SEAT IN TUB - ACCESSIBLE TO PERSONS WITH DISABILITIES. COMMON USE FACILITIES INCLUDE, BUT ARE NOT LIMITED TO, LOBBIES, MULTIPLE ACCOMMODATION
CLEAR SIDE APPROACH 15"-16" 15"-16" DRINKING FOUNTAINS
TOILET & BATHING FACILITIES, LAUNDRY FACILITIES, COMMUNITY ROOMS, CLUBHOUSES, HEALTH & FITNESS FACILITIES, TOILET FACILITY
MIN.
30"

FLOOR (FIGURE 11A-11A)

(FIG. 11B-610.3.1) (FIG. 11B-610.3.2) GAME ROOMS & PORTIONS OF COMMON USE TENANT STORAGE. ALL ENTRANCES, DOORS, FIXTURES & CONTROLS SHALL (FIG. 11A-9A)
SPACE CLEAR FLOOR SPACE AT BATHTUBS
(FIG. 11A-9E & 11B-607.2) BE ON AN ACCESSIBLE ROUTE. FACILITIES & FIXTURES REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH THE

LENGTH OF BATHTUB 12"MIN

OPEN SHOWER
(FIG. 11A-9J) 24"
SINGLE LEVER
MIXING VALVE 24"
ACCESSIBLE TELEPHONES:
FOLLOWING PROVISIONS:
ISSUED BY
(C.B.C.-1140A) 18" 32" MIN. Community Development Department
MAX. CONTROL 1.DOORS: DOORS TO ACCESSIBLE BATHROOMS SHALL COMPLY WITH SECTION 1126A. DOORS SHALL NOT SWING INTO
MIN. CLR.
19" THE FLOOR SPACE REQUIRED FOR ANY FIXTURE.
TOP OF HOSE DESIGN OPTION
GENERAL.
By: Ann Rosendale
GRAB BARS @ BATHTUBS SEAT MOUNTING STANDARD HEAD 2. CLEAR FLOOR SPACE: ALL FIXTURES & CONTROLS SHALL BE ON AN ACCESSIBLE ROUTE. CLEAR FLOOR SPACES AT
35"-37"

(FIG. 11A-9F, 11B-607.4.1 & 12" 24" 24" 36" MIN. BRACKET
WHEN PUBLIC TELEPHONES PROVIDED, THEY SHALL COMPLY WITH THIS SECTION. ON FLOORS WHERE PUBLIC
FIXTURES & CONTROLS, THE ACCESSIBLE ROUTE & THE TURNING SPACE MAY OVERLAP. THIS CLEAR SPACE SHALL on Jan 20, 2023
11B-607.4.2) 24" GRAB BAR FLEXIBLE TELEPHONES ARE PROVIDED, AT LEAST ONE TELEPHONE SHALL BE ACCESSIBLE. ON ANY FLOOR WHERE TWO OR
MIN. MAX. MIN. MAX. COMPLY WITH SECTIONS 1138A.1.4 & 1138A.3.
SHOWER SPRAY MORE BANKS OF MULTIPLE TELEPHONES ARE PROVIDED, AT LEAST ONE TELEPHONE IN EACH BANK SHALL BE FLUSH ACTIVATOR FLUSH ACTIVATOR
CONTROL 12"
24" MIN. HOSE - 59" LONG ACCESSIBLE. (C.B.C.-1140A.1) 17"-18" ON WIDE SIDE 17"-19" ON WIDE SIDE
17"-19"

AREA MIN. 3. WATER CLOSETS: WHERE A TOILET STALL IS PROVIDED, IT SHALL COMPLY WITH SECTION 1127A.2.1 OR 1127A.2.2, & ITS
48" MAX.
8"-10"

12" MIN. 24" MAX. 24" MIN.

WATER CLOSET SHALL COMPLY WITH SECTION 1127A.2.3.
39"-41"

GRAB BAR CLEAR FLOOR OR GROUND SPACE.

33"-36"

BACK WALL
12" MIN.

SEAT

MAX.

MAX.
A CLEAR FLOOR OR GROUND SPACE AT LEAST 30" BY 48" THAT ALLOWS EITHER FORWARD OR PARALLEL APPROACH

FOR FLOOR-MOUNTED W.C.

GRAB BAR
HEAD END

4. LAVATORY & MIRRORS: WHERE A LAVATORY AND/OR MIRROR IS PROVIDED, IT SHALL COMPLY WITH SECTIONS1127A.3

12"

12"
FOR WALL-MOUNTED W.C.
BY A PERSON USING A WHEELCHAIR SHALL BE PROVIDED AT TELEPHONES. THE CLEAR FLOOR OR GRUND SPACE
33"-36"

SEAT MILESTONE:
WALL

AND/OR 1127A.8.3.
24" MIN.

MIN. SHALL COMPLY WITH SECTION1138 A.1.4. BASES, ENCLOSURES & FIXED SEATS SHALL NOT IMPEDE APPROACHES TO THIRD CITY SUBMITTAL

54" MIN.

54" MIN.
TELEPHONES BY PEOPLE WHO USE WHEELCHAIRS. (FIG. 11A-11B).
5. CONTROLS & DISPENSERS: WHERE CONTROLS, DISPENSERS, RECEPTACLES OR OTHER TYPES OF EQUIPMENT ARE
PROVIDED, AT LEAST ONE OF EACH SHALL COMPLY WITH SECTIONS1127.8 & 1138A.3.

COM-2213627 to COM-2213634
56" MIN.

59" MIN.

60" MIN.
(a) PLAN (b) ELEVATION CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS MAY BE PART OF THE KNEE SPACE REQUIRED UNDER SOME
OBJECTS. (C.B.C.-1140A.2)

48" MIN. CLR.

END WALL

PLAN CONTROL END (FOOT) WALL BACK WALL HEAD END WALL
CONTROL

24"

24"
6. BATHING & SHOWER FACILITIES: WHERE BATHTUBS OR SHOWERS ARE PROVIDED, AT LEAST ONE FIXTURE OF EACH DRAWN: MH, NM
TYPE PROVIDED SHALL BE ACCESSIBLE PER ROOM. FOR BATHTUBS, SEE SECTION1127A.5.2. FOR SHOWERS, SEE
(a) WITH REMOVABLE SEAT IN TUB RELATIONSHIP OF MANEUVERING CLEARANCES TO WHEELCHAIR SPACES. CHECKED:
SECTION 1127A.5.3. JM
ONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR OR GROUND SPACE FOR A WHEELCHAIR SHALL ADJOIN 4"
48" 15" TOILET ROOM FIXTURES & ACCESSORIES: (C.B.C.-1127A.8) ANOTHER WHEELCHAIR CLEAR FLOOR SPACE. IF A CLEAR FLOOR SPACE IS LOCATED IN AN ALCOVE OR OTHERWISE MAX. PLOT DATE: Monday, October 24, 2022
24" 12" 7. TOILET FACILITIES: TOILET FACILITIES SHALL COMPLY WITH SECTION 1127A.2.
CONFINED ON ALL OR PART OF THREE SIDES, ADDITIONAL MANEUVERING CLEARANCES SHALL BE PROVIDED. 60" MIN. 35"-37" MIN.
MIN. MAX. MIN. MAX.
TOWEL, SANITARY NAPKINS, WASTE RECEPTACLES: (C.B.C.-1140A.3)
CONTROL 8. LAUNDRY FACILITIES: LAUNDRY FACILITIES SHALL COMPLY WITH SECTION 1127A.10
12" MIN. 15" MIN. WHERE TOWEL, SANITARY NAPKINS, WASTE RECEPTACLES & OTHER SIMILAR DISPENSING & DISPOSAL FIXTURES ARE E D A RC
AREA
ER
8"-10"

PROVIDED, AT LEAST ONE OF EACH TYPE SHALL BE LOCATED WITH ALL OPERABLE PARTS, INCLUDING COINS SLOTS, MOUNTING HEIGHT.
9. STORAGE FACILITIES: STORAGE FACILITIES SHALL COMPLY WITH SECTION 1127A.11. 18" 32" MIN.
R Z JA

H
ST
WITHIN 40" FROM THE FINISHED FLOOR. CONTROLS AND OPERATING MECHANISMS SHALL COMPLY WITH SECTION 1138A.4. THE HIGHEST OPERABLE PART OF THE TELEPHONE SHALL BE WITHIN THE REACH RANGES SPECIFIED IN SECTION
MIN. CLR. MA B

IT E
(C.B.C.-1127A.8.1) 1138A.3. (FIG. 11A-11B) (C.B.C.-1140A.4)
HEAD END

R EG I
10. FIXED OR BUILT-IN SEATING, TABLES & COUNTERS: FIXED OR BUILT-IN SEATING, TABLES & COUNTERS SHALL COMPLY

FA RA
33"-36"
SEAT

BA
WALL
24" MIN.

WITH SECTION1127A.12.

CT
TOILET TISSUE DISPENSERS, ENCLOSURES.

RI
(C.B.C.-1127A.1)
No. C 15528

THIRD CITY SUBMITTAL 10/26/2022

SHALL BE LOCATED ON THE WALL OR PARTITION WITHIN 7" MIN. & 9" MAX. OF THE FRONT EDGE OF THE WATER CLOSET IF TELEPHONE ENCLOSURES ARE PROVIDED, THEY SHALL COMPLY WITH SECTIONS 1140A.5.1 & 1140A.5.2. (c) ACCESSIBLE W.C. COMPARTMENT WITHIN A (d) AMBULATORY ACCESSIBLE
MEASURED TO THE CENTERLINE OF THE DISPENSER. THE OUTLET OF DISPENSER SHALL BE BELOW THE GRAB BAR, 19" MULTIPLE-ACCOMMODATION TOILET FACILITY COMPARTMENT
MIN. ABOVE THE FINISHED FLOOR. THE OUTLET DISPENSER SHALL NOT BE LOCATED BEHIND THE GRAB BARS. PARALLEL APPROACH. WHERE PARALLEL APPROACH IS PROVIDED, THE DISTANCE FROM THE EDGE OF THE NOTE:
Exp. 03/31/23
________
(FIG. 11B-604.2) (FIG. 11B-604.2)
END WALL

PLAN CONTROL END (FOOT) WALL BACK WALL HEAD END WALL TELEPHONE ENCLOSURE TO THE FACE OF TELEPHONE UNIT SHALL BE 10" MAX. (C.B.C.-1140A.5.1.)
CONTROL

DISPENSERS SHALL NOT BE OF A TYPE THAT CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS PAPER ALL DIMENSIONS SHOWN ARE
TA

IA
N

S
FLOW. (FIG. 11A-9B). (C.B.C.-1127A.8.2) TE
O F CA L I F O R
MIN. CLEAR DIMENSIONS FINISH 36" MIN.
(a) WITH PERMANENT SEAT AT HEAD OF TUB FORWARD APPROACH. 60" TO FINISH. GRAB BAR
MIRRORS. WHERE A FORWARD APPROACH PROVIDED, THE COUNTER MAY EXTEND BEYOND THE FACE OF THE TELEPHONE 20" MIN. 36"MIN.
42" MIN. GRAB BAR 54" MIN.
WHERE MIRRORS ARE PROVIDED, AT LEAST ONE SHALL BE MOUNTED WITH THE BOTTOM EDGE OF REFLECTING SURFACE MAX. INTO THE REQUIRED CLEAR FLOOR OR GROUND SPACE, & ENCLOSURE MAY EXTEND BEYOND THE FACE OF GRAB BAR
NO HIGHER THAN 40" MAX. ABOVE THE FINISH FLOOR WHEN LOCATED ABOVE COUNTERTOPS. MIRRORS NOT LOCATED THE TELEPHONE 24" MAX. IF AN ADDITIONAL 6" IN WIDTH OF CLEAR FLOOR SPACE IS PROVIDED, CREATING A CLEAR 12" 12" 24"
SHOWERS: ALL DISPENSERS
ABOVE A COUNTERTOP SHALL BE INSTALLED WITH BOTTOM EDGE OF REFLECTING SURFACE 35" FROM THE FINISH FLOOR SPACE OF 36" x 48", THE ENCLOSURE MAY EXTEND MORE THAN 24" BEYOND THE FACE OF THE TELEPHONE.

MIN. CLR.
(C.B.C. - 1127A.5.3) +40" MAX. TO MAX. PROJECT NO. 2021-051

VITREOUS CHINA
PENNINGTON
K-T13140-3B
LAVATORY
PINSTRIPE
FAUCETS
K-2196-8
BRASS

VITREOUS CHINA
PENNINGTON
K-T13140-3B
LAVATORY
PINSTRIPE
FAUCETS
K-2196-8
BRASS

VITREOUS CHINA
PENNINGTON
K-T13140-3B
LAVATORY
PINSTRIPE
FAUCETS
K-2196-8
BRASS
FLOOR. (C.B.C.-1127A.8.3) (C.B.C.-1140A.5.2)

R.
HIGHEST 7"-9"

CL
34"

33" - 36"
SHOWER SHALL COMPLY WITH THE FOLLOWING (FIG. 11A-9H - 11A-9K): OPERABLE PART .

33"-36"
PROJECT PHASE

.
IN 60"
EQUIPMENT FOR HEARING IMPAIRED PEOPLE.

IA
TRANSFER

.D

MIN. CLR.
COMMON ACCESSIBLE LAUNDRY ROOMS. TELEPHONES SHALL BE EQUIPPED WITH THE RECEIVER THAT GENERATES A MAGNETIC FIELD IN THE AREA OF THE SIDE

17"-19"
MIN.
.
SHEET TITLE

19"
SIZE AND CLEARANCE. RECEIVER CAP. A REASONABLE NUMBER OF THE PUBLIC TELEPHONES PROVIDED, BUT ALWAYS AT LEAST ONE ON

44"
(C.B.C.-1127A.10)

M
1. STANDARD ROLL-IN SHOWER COMPARTMENTS SHALL MEET ONE OF THE FOLLOWING: 30" X 48"
EACH FLOOR OR IN EACH BANK, WHICHEVER IS MORE, IN A BUILDING OR FACILITY, SHALL BE EQUIPPED WITH THE
PUBLIC AREA
MIN.

MIN.
1.1. 30" MIN. IN DEPTH AND 60" MIN. IN WIDTH BETWEEN WALL SURFACES MEASURED AT CENTER POINTS OF 18" CLR. SPACE
60"

VOLUME CONTROL. (FIG. 11A-11D). (C.B.C.-1140A.6) 42" MIN.

WHEN DOOR SWINGS IN

WHEN DOOR SWINGS IN

OPPOSING SIDES, WITH A FULL OPENING WIDTH ON THE LONG SIDE. A CLEAR FLOOR SPACE 30" MIN. BY 60" MIN. GENERAL.
FLOOR MOUNTED W.C.

GRAB BAR (a) SIDE ELEVATION (b) FRONT VIEW

WALL MOUNTED W.C.

SHALL BE PROVIDED ADJACENT TO THE OPEN FACE OF THE SHOWER COMPARTMENT. WHERE COMMON USE LAUNDRY ROOMS ARE PROVIDED, AT LEAST ONE OF EACH TYPE OF APPLIANCE PROVIDED IN EACH
TEXT TELEPHONES.
CODE
59" MIN. @

54" MIN. @

1.2. 42" IN WIDTH BETWEEN WALL SURFACES, AND 48" MIN. DEPTH WITH AN ENTRANCE OPENING OF 42". LAUNDRY AREA SHALL BE ACCESSIBLE, SHALL BE ON AN ACCESSIBLE ROUTE AND SHALL COMPLY WITH THIS SECTION.
IF A TOTAL OF FOUR OR MORE PUBLIC PAY TELEPHONES ARE PROVIDED AT THE INTERIOR & EXTERIOR OF THE SITE,
32"
MIN.

SUCH APPLIANCES INCLUDE CLOTHES WASHING MACHINES, DRYERS, SOAP DISPENSERS & ANY RELATED FEATURES
24"

AND IF AT LEAST ONE OF THE TOTAL NUMBER PROVIDED IS LOCATED IN AN INTERIOR LOCATION, AT LEAST ONE
REFERENCES

56" MIN.
2. ALTERNATE ROLL-IN SHOWER COMPARTMENTS. SHALL BE 36" MIN. IN DEPTH AND 60" MIN. IN WIDTH BETWEEN WALL SUCH AS WASH SINKS, TABLES & STORAGE AREAS. MIN. CLR.
INTERIOR PUBLIC TEXT TELEPHONE SHALL BE PROVIDED. (C.B.C.-1140A.7) 32"
SURFACE MEASURED AT CENTER POINTS OF OPPOSING SIDES. A 36" WIDE MIN. ENTRY SHALL BE PROVIDED AT ONE WHERE LAUNDRY ROOMS ARE PROVIDED ON FLOORS OF AN ELEVATOR BUILDING, EACH LAUNDRY ROOM SHALL BE
MIN.

MIN. CLR.
54"

END OF THE LONG SIDE OF THE COMPARTMENT. ACCESSIBLE. WHERE THERE IS ONE LAUNDRY ROOM ON A GROUND FLOOR IN EACH BUILDING, EACH LAUNDRY ROOM * REAR GRAB BAR
SIGNAGE.
(C.B.C.-1127A.5.3.1) SHALL BE ACCESSIBLE. WHERE THERE IS A LAUNDRY ROOM ON THE GROUND FLOOR OF A BUILDING & ANOTHER LOCATED ALLOWED AT 36" A.F.F.
TEXT TELEPHONES SHALL BE IDENTIFIED BY THE INTERNATIONAL TTY SYMBOL (FIG. 11A-11C) . IF A FACILITY HAS A WATER CLOSETS
IN THE BASEMENT, IT IS ACCEPTABLE TO HAVE ONLY THE GROUND FLOOR LAUNDRY ROOM ACCESSIBLE. AT TANK-TYPE TOILET
PUBLIC TEXT TELEPHONE, DIRECTIONAL SIGNAGE INDICATING THE LOCATION OF THE NEAREST SUCH TELEPHONE (FIG. 11A-9B) SHEET NO.
THRESHOLDS. (C.B.C.-1127A.10.1)
SHALL BE PLACED ADJACENT TO ALL BANKS OF TELEPHONES THAT DO NOT CONTAIN A TEXT TELEPHONE. SUCH 60" X 60"
THRESHOLDS IN A ROLL-IN SHOWER COMPARTMENTS SHALL BE 12" MAX. IN HEIGHT AND SHALL BE BEVELED WITH A

A9-1.3
DIRECTIONAL SIGNAGE SHALL INCLUDE THE INTERNATIONAL TTY SYMBOL. IF A FACILITY HAS NO BANKS OF LEVEL & CLR. 60" MIN.
SLOPE NO GREATER THAN 1 UNIT VERTICAL IN 2 UNITS HORIZONTAL (50% SLOP). CLEAR FLOOR SPACE. (FIG. 11B-1B)
TELEPHONES, THE DIRECTIONAL SIGNAGE SHALL BE PROVIDED AT THE ENTRANCE OR IN A BUILDING DIRECTORY.
12" MAX.

THERE SHALL BE A MIN. CLEAR SPACE 30" PERPENDICULAR BY 48" PARALLEL IN FRONT OF CLOTHES WASHER & DRYERS 36" MIN. GRAB BAR
(C.B.C.-1140A.7.1) 17"-18" MULTIPLE ACCOMMODATION TOILET (c) CLEAR FLOOR SPACE AT
EXCEPTION: CHANGES IN LEVEL NOT EXCEEDING 1/4" SHALL BE PERMITTED VERTICAL. (FIG. 11A-1F) (C.B.C.-1127A.5.3.2) REQUIRED TO BE ACCESSIBLE. THERE SHALL BE A MIN. CLEAR SPACE 30" X 48" PROVIDED FOR AT LEAST ONE OF EACH
FACILITY (FIG. 11A-9A) WATER CLOSETS
TYPE OF FIXTURE OR APPLIANCE PROVIDED IN THE LAUNDRY ROOM (E.G.SOAP DISPENSERS, WASH SINKS, TABLES, FLUSH ACTIVATOR
HEIGHT.
STORAGE AREAS). (C.B.C.-1127A.10.2) ON WIDE SIDE
WHEN IN USE, THE TOUCH SURFACE OF TTY KEYPAD SHALL BE 34" MIN. ABOVE FINISHED FLOOR. (C.B.C.-1140A.7.2)
 WATER CLOSETS. A ( A ) . (C.B.C.-1124A.11)

JOB COPY
WATER CLOSETS REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH THE FOLLOWING: GENERAL. DIRECTIONAL / INFORMATIONAL SIGNAGE
PLATFORM (WHEELCHAIR) LIFTS MAY BE PROVIDED BETWEEN LEVELS, IN LIEU OF PASSENGER ELEVATORS, WHEN THE (C.B.C.-1143A)
1. HEIGHT. THE HEIGHT OF ACCESSIBLE WATER CLOSETS SHALL BE MIN. 17" TO A MAX. 19" MEASURED TO THE TOP OF VERTICAL DISTANCE BETWEEN LANDINGS, AS WELL AS THE STRUCTURAL DESIGN AND SAFEGUARDS ARE AS ALLOWED

ALL IDEAS, DESIGN ARRANGEMENTS AND PLANS INDICATED OR REPRESENTED BY THIS DRAWING ARE OWNED BY AND THE PROPERTY OF ARK ARCHITECTS, INC. AND WERE CREATED EVOLVED AND DEVELOPED FOR USE ON AND IN CONNECTION WITH THE SPECIFIED PROJECT. NONE OF SUCH IDEAS ARRANGEMENTS OR PLANS SHALL BE USED BY OR DISCLOSED TO ANY PERSON FIRM OR CORPORATION FOR ANY PURPOSE WHATSOEVER WITHOUT THE WRITTEN PERMISSION OF ARK ARCHITECTS, INC.
2.
A MAX. 2" HIGH TOILET SEAT.

CONTROLS. FLUSH CONTROLS SHALL BE HAND OPERATED OR AUTOMATIC. HAND OPERATED CONTROLS SHALL BE
BY ASME A18.1 (SAFETY STANDARD FOR PLATFORM LIFTS AND STAIRWAY CHAIR LIFTS), CALIFORNIA CODE OF
REGULATIONS, TITLE 8 (ELEVATOR SAFETY ORDERS), AND ANY APPLICABLE SAFETY REGULATIONS OF OTHER
ADMINISTRATIVE AUTHORITIES HAVING JURISDICTION.
NOTE:
THE AUTOMATIC DOOR REOPENING DEVICE IS ACTIVATED IF AN OBJECT
PASSES THROUGH EITHER LINE "A" OR "B". LINE "A" & LINE "B" REPRESENT
3" MIN.
GENERAL.
WHERE SIGNS AND OR IDENTIFICATION DEVICES ARE PROVIDED THEY SHALL COMPLY WITH SECTION 1143A.
EXCEPTION: SIGNS NEED NOT BE PROVIDED WITHIN DWELLING UNITS.
SIGNAGE REQUIREMENTS. (INTERIOR EXIT STAIRWAYS AND RAMPS SECTION 1023)
STAIRWAY IDENTIFICATION SIGNS SHALL COMPLY WITH THE FOLLOWING REQUIREMENTS: A R K
OPERATED WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING OR TWISTING. CONTROLS FOR 1. THE SIGNS SHALL BE A MINIMUM SIZE OF 18" x 12".
THE VERTICAL LOCATIONS OF THE DOOR REOPENING DEVICE NOT (C.B.C.-1143A.1)
THE FLUSH VALVES SHALL BE MOUNTED ON THE OPEN SIDE OF THE WATER CLOSET NO MORE THAN 44" ABOVE THE IF LIFTS ARE PROVIDED, THEY SHALL BE DESIGNED AND CONSTRUCTED TO FACILITATE UNASSISTED ENTRY, OPERATION 2. THE LETTERS DESIGNATING THE IDENTIFICATION OF THE INTERIOR EXIT STAIRWAY AND RAMP, SUCH AS "STAIR
REQUIRING CONTACT.
FLOOR. THE FORCE REQUIRED TO ACTIVATE CONTROL SHALL BE NO GREATER THAN 5 POUNDS. AND EXIT FROM THE LIFT, AND SHALL COMPLY WITH RESTRICTIONS AND ENHANCEMENTS OF THIS SECTION IN
IDENTIFICATION SIGNS. NO. 1" OR "WEST STAIR", SHALL BE PLACED AT THE TOP OF THE SIGN AND SHALL BE A MINIMUM OF 1-1/2" IN ARCHITECTS, INC.

3" MIN.
CONJUNCTION WITH TITLE 8 OF THE CALIFORNIA CODE OF REGULATIONS. (C.B.C.-1124A.11.1) HEIGHT BLOCK LETTERING WITH 14" STROKES.
WHEN SIGNS IDENTIFY PERMANENT ROOMS AND SPACES OF A BUILDING OR SITE, THEY SHALL COMPLY WITH SECTIONS
3. TOILET SEATS. SEATS SHALL NOT BE SPRUNG TO RETURN TO A LIFTED POSITION. FLOOR SIGNAGE ON 3. THE NUMBER DESIGNATING THE FLOOR LEVEL SHALL BE A MINIMUM OF 5" IN HEIGHT WITH 3 4" STROKES AND
1143A.1, 1143A.5, 1143A.6, 1143A.7,
(C.B.C.-1127A.2.3) SIZE AND CLEAR FLOOR SPACE. LANDING JAMB LOCATED IN THE CENTER OF THE SIGN. THE MEZZANINE LEVELS SHALL HAVE THE LETTER "M" PRECEDING THE
EXCEPTION: EXTERIOR SIGNS THAT ARE NOT LOCATED AT THE DOOR TO THE SPACE THEY SERVE SHALL NOT BE Faramarz Jabbari, AIA
PLATFORM (WHEELCHAIR) LIFTS SHALL BE OF SUFFICIENT SIZE TO ACCOMMODATE A WHEELCHAIR IN ACCORDANCE WITH (SEE DETAIL BELOW) FLOOR LEVEL. BASEMENT LEVELS SHALL HAVE THE LETTER "B" PRECEDING THE FLOOR NUMBER.
REQUIRED TO COMPLY WITH SECTION 1143A.6.
ACCESSIBLE URINALS. SECTION 1138A.1.4. (C.B.C.-1124A.11.2) 4. OTHER LETTERING AND NUMBERS SHALL BE A MINIMUM OF 1" IN HEIGHT.
(C.B.C.-1143A.2)
5. THE STAIRWAY'S UPPER TERMINUS, SUCH AS ROOF ACCESS OR NO ROOF ACCESS, SHALL BE PLACED UNDER
WHEN URINALS ARE PROVIDED, AT LEAST ONE SHALL COMPLY WITH THE FOLLOWING: LIFT ACCESS. THE STAIRWAY IDENTIFICATION IN 1" HIGH BLOCK LETTERING WITH 14" STROKES. 2240
DIRECTION AND INFORMATIONAL SIGNS.
THERE SHALL BE A LEVEL AND CLEAR FLOOR AREA OR LANDING AT EACH FLOOR OR LEVEL SERVED BY PLATFORM 6. THE LOWER AND UPPER TERMINUS OF THE STAIR WAY SHALL BE PLACED AT THE BOTTOM OF THE SIGN IN 1"
WHEN SIGNS DIRECT TO OR GIVE INFORMATION ABOUT PERMANENT ROOMS AND SPACES OF A BUILDING OR SITE, THEY Faraday Road
1. HEIGHT AND WALL PROJECTION. URINALS SHALL BE FLOOR MOUNTED (STALL TYPE) OR WALL HUNG. THE RIM OF THE (WHEELCHAIR) LIFTS. CLEAR FLOOR AREAS OR LANDINGS SHALL MEET THE APPLICABLE "ACCESSIBLE ROUTE" HIGH BLOCK LETTERING WITH 14" STROKES.
EMERGENCY 2 1/2" H, 2 12" W SHALL COMPLY WITH SECTIONS 1143A.5,
WALL HUNG URINALS SHALL BE 17" MAX. ABOVE FINISH FLOOR. URINALS (FLOOR MOUNTED & WALL HUNG) SHALL BE REQUIREMENTS. (C.B.C.-1124A.11.3) 7. CHARACTERS AND THEIR BACKGROUND SHALL HAVE A NON-GLARE FINISH. CHARACTERS SHALL CONTRAST
SERVICE (1124A.6 #1) (C.B.C.-1143A.3)
1312" DEEP MIN. MEASURED FROM THE OUTER FACE OF THE RIM TO THE BACK OF THE FIXTURE. WITH THEIR BACKGROUND, WITH EITHER LIGHT CHARACTERS ON A DARK BACKGROUND OR DARK
STANDBY POWER. SIGNAGE EACH Carlsbad, California
36" MIN. ACCESSIBILITY SIGNS. CHARACTERS ON A LIGHT BACKGROUND.
TO ENSURE CONTINUED OPERATION IN CASE OF PRIMARY POWER LOSS, PLATFORM (WHEELCHAIR) LIFTS SHALL BE SIDE (WHERE HALL
2. FLUSH CONTROLS. FLUSH CONTROLS SHALL BE HAND OPERATED OR AUTOMATIC. HAND OPERATED CONTROLS (1124A.3.2.1) WHEN SIGNS IDENTIFY, DIRECT OR GIVE INFORMATION ABOUT ACCESSIBLE ELEMENTS AND FEATURES OF A BUILDING OR 8. WHEN SIGNS REQUIRED BY SECTION 1023.9 ARE INSTALLED IN INTERIOR EXIT STAIRWAYS AND RAMPS OF 92008
PROVIDED WITH STANDBY POWER OR WITH SELF-RECHARGEABLE BATTERY POWER THAT PROVIDES SUFFICIENT POWER OCCURS) LANTERN
SHALL BE OPERABLE WITH ONE HAND, SHALL NOT REQUIRE TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST SITE, THEY SHALL INCLUDE THE APPROPRIATE SYMBOL OF ACCESSIBILITY AND SHALL COMPLY WITH SECTION 1143A.5. BUILDINGS SUBJECT TO SECTION 1025, THE SIGNS SHALL BE MADE OF THE SAME MATERIAL AS REQUIRED BY
TO OPERATE ALL PLATFORM LIFT FUNCTIONS FOR A MINIMUM OF FIVE UPWARD AND DOWNWARD TRIPS. AUTOMATIC DOOR Tel: (858) 792-5997
& SHALL BE MOUNTED NO MORE THAN 44" ABOVE FLOOR. THE FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE (C.B.C.-1143A.4) SECTION 1025.4.
(C.B.C.-1124A.11.4) REOPENING DEVICES Fax: (858) 792-5858
NO GREATER THAN 5 POUNDS. ELECTRONIC AUTOMATIC FLUSHING CONTROLS PREFERABLE. (C.B.C. 1023.9.1)
(1124A.9)
VISUAL CHARACTERS.
3. CLEAR FLOOR SPACE. A CLEAR FLOOR SPACE 30" BY 48" SHALL BE PROVIDED IN FRONT OF THE URINAL TO ALLOW OPENNESS.
SIGNS WITH VISUAL CHARACTERS SHALL COMPLY WITH THIS SECTION. (C.B.C.-1143A.5)
FORWARD APPROACH. THE CLEAR FLOOR SPACE SHALL COMPLY WITH SECTION 1138.1.4. PLATFORM (WHEELCHAIR) LIFTS ON AN ACCESSIBLE MEANS OF EGRESS SHALL NOT BE INSTALLED IN A FULLY ENCLOSED

1-1/2"
HALL CALL
(C.B.C.-1127A.2.4) HOISTWAY. (C.B.C.-1124A.11.5) BUTTONS

48" MIN. - 60" MAX.

1. FINISH & CONTRAST: CHARACTERS & THEIR BACKGROUND SHALL HAVE A NON GLARE FINISH. AND SHALL 09/12/2022
(1124A.4) CONTRAST WITH THEIR BACKGROUND, EITHER LIGHT ON DARK BACKGROUND OR DARK ON LIGHT BACKGROUND. A SECOND CITY SUBMITTAL
ACCESSIBLE LAVATORIES.
DOORS AND GATES.
LIFTS SHALL HAVE LOW ENERGY POWER-OPERATED DOORS AND GATES, WHICH SHALL REMAIN OPEN FOR 20 SECONDS
2. CHARACTER TYPE: CHARACTERS SHALL BE UPPERCASE, LOWERCASE, OR A COMBINATION OF BOTH. CHARACTERS WEST STAIR 10/26/2022

(1124A.8)
MINIMUM. END DOORS SHALL HAVE 32 INCHES MINIMUM CLEAR OPENING WIDTH. SIDE DOORS CLEAR OPENING WIDTH B THIRD CITY SUBMITTAL
SHALL BE CONVENTIONAL IN FORM, AND SHALL NOT BE ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF OTHER

(1124A.6 #3)
72" MIN.
WHEN COMMON USE LAVATORIES ARE PROVIDED FOR RESIDENTS OR GUEST, AT LEAST ONE, AND NOT LESS THAN 1 %
NO ROOF ACCESS

.
SHALL BE 42 INCHES MINIMUM.

1"
OF ALL LAVATORIES, SHALL COMPLY WITH THE FOLLOWING: UNUSUAL FORMS.
3 ----
EXCEPTION: LIFTS HAVING DOORS OR GATES ON OPPOSITE SIDES SHALL BE PERMITTED TO HAVE SELF-CLOSING B
1. LOCATION. LAVATORIES SHALL BE INSTALLED WITH THE CENTERLINE OF THE FIXTURE A MIN. 18" HORIZONTALLY 3. PROPORTIONS: CHARACTERS ON SIGNS SHALL BE SELECTED FROM FONTS WHERE THE WIDTH OF THE UPPERCASE

2
MANUAL DOORS AND GATES. (C.B.C.-1124A.11.6)
FROM AN ADJOINING WALL, PARTITION OR FIXTURE. THE TOP OF THE FIXTURE RIM SHALL BE A MAX. OF 34" ABOVE 3
4" MIN. DIA. &
LETTER "O" IS 60% MIN. & 110% MAX. OF THE HEIGHT OF THE UPPERCASE LETTER "I". 4 ----
THE FINISH FLOOR. RESTRICTION SIGN. SHALL BE

(1124A.4)
42"
RAISED 18"±132" 4. CHARACTER HEIGHT: VISUAL CHARACTERS SHALL BE SIZED IN ACCORDANCE TO TABLE 1143A.5. VIEWING
A SIGN COMPLYING WITH SECTION 1143A SHALL BE SECURELY FASTENED IN A CONSPICUOUS PLACE AT EACH LANDING

12"
5

5"
2. FLOOR SPACE. A CLEAR FLOOR SPACE AT LEAST 30" BY 48" SHALL BE PROVIDED IN FRONT OF ACCESSIBLE (1124A..4) DISTANCE SHALL BE MEASURED AS THE HORIZONTAL DISTANCE BETWEEN THE CHARACTER AND AN OBSTRUCTION ----
AND ON THE PLATFORM. THE SIGN SHALL STATE "NO FREIGHT" IN LETTERS NOT LESS THAN 5 8 INCH HIGH AND INCLUDE

29"
LAVATORIES TO ALLOW FORWARD APPROACH. SUCH CLEAR FLOOR SPACE SHALL ADJOIN OR OVERLAP AN PREVENTING FURTHER APPROACH TOWARDS THE SIGN. CHARACTER HEIGHT SHALL BE BASED ON THE UPPERCASE
THE "INTERNATIONAL SYMBOL OF ACCESSIBILITY". (C.B.C.-1124A.11.7)
ACCESSIBLE ROUTE OR ANOTHER CLEAR FLOOR SPACE. LETTER "I". 6 ----
A
3. KNEE AND TOE SPACE. A CLEAR & UNOBSTRUCTED KNEE & TOE SPACE, COMPLYING WITH SECTION 1138A.2, SHALL 80" MIN. VISUAL CHARACTER HEIGHT (TABLE 1143A.5 & 11B-703.5.5) MIN. 7 ----

5"
BE PROVIDED UNDERNEATH THE LAVATORY. THE KNEE & TOE SPACE SHALL BE CENTERED ON THE FIXTURE. THE 68" MIN.
HEIGHT TO FINISH FLOOR FROM HORIZONTAL VIEWING MINIMUM CHARACTER
FLOOR 1 TO 5

1"
CLEAR FLOOR SPACE REQUIRED BY ITEM 2 SHALL NOT EXTEND INTO THE KNEE & TOE SPACE MORE THAN 19". (SEE BASELINE OF CHARACTER DISTANCE HEIGHT
FIG. 11A-9D) 8 ----
40" TO LESS THAN OR EQUAL TO 70" LESS THAN 72" 5
8" GRADE II BRAILLE
5
4. FINISHED FLOOR. THE FINISHED FLOOR BENEATH THE LAVATORY SHALL BE EXTENDED TO THE WALL. 72" AND GREATER 8 ", PLUS 18" PER FOOT OF VIEWING DISTANCE ABOVE 72" 9 ----
TYPICAL ELEVATOR ELEVATION GREATER THAN 70" TO LESS THAN LESS THAN 180" 2"
5. PLUMBING PROTECTION. WATER SUPPLY & DRAIN PIPES ACCESSIBLE UNDER LAVATORIES SHALL BE INSULATED OR ON GRADE LEVEL, A
OR EQUAL TO 120" 180" AND GREATER 2", PLUS 18" PER FOOT OF VIEWING DISTANCE ABOVE 180" 18"
OTHERWISE COVERED TO PROTECT AGAINST CONTACT. THERE SHALL BE NO SHARP OR ABRASIVE SURFACE UNDER RAISED FIVE-POINTED ARIZONA # : 27259

51" MIN.

51" MIN.
3"

54" MIN.

54" MIN.
LAVATORIES. STAR SHALL BE LESS THAN 21'
GREATER THAN 120"
PLACED TO THE LEFT 21' AND GREATER 3", PLUS 18" PER FOOT OF VIEWING DISTANCE ABOVE 21' CALIFORNIA # : C15528
6. LAVATORY FAUCET CONTROLS. FAUCET CONTROLS & OPERATION MECHANISMS SHALL BE OPERABLE WITH ONE OF THE RAISED COLORADO # : 304356
ALTERNATE 5. HEIGHT FROM FINISH FLOOR: VISUAL CHARACTERS SHALL BE 40" MIN. ABOVE FINISH FLOOR.
HAND & SHALL NOT REQUIRE TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO CHARACTER W/ 2"
LOCATION OF EXCEPTIONS: ELEVATOR CAR TO ACCOMMODATE GURNEY: OREGON # : 5318
ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 POUNDS. LEVER OPERATED, PUSH TYPE & ELECTRONICALLY OUTSIDE DIA.
PANEL 1. VISUAL CHARACTERS INDICATING ELEVATOR CAR CONTROLS.
CONTROLLED MECHANISMS ARE EXAMPLES OF ACCEPTABLE DESIGNS. HAND OPERATED METERING FAUCETS ARE (1124A.8) FLOOR LANDING NEVADA # : 2838
ALLOWED IF THE FAUCET REMAINS OPEN FOR AT LEAST 10 SECONDS. SIGNAGE IS 2. FLOOR-LEVEL EXIT SIGNS COMPLYING WITH CHAPTER 10, SECTION 1011.6.
2" MIN. 2" TEXAS # : 16533
(C.B.C.-1127A.3) REQUIRED ON JAMB
HEIGHT 6. STROKE THICKNESS: STROKE THICKNESS OF THE UPPERCASE LETTER "I" SHALL BE 10% MIN. AND 20% MAX. OF ELEVATOR CAR TO ACCOMMODATE GURNEY
(1124A.8) PANELS ON BOTH AT LEAST ONE ELEVATOR PER BUILDING SHALL BE SIZED TO ACCOMMODATE A GURNEY THAT IS 24 BY 84 INCHES WITH UTAH # : 7288093-0301
36" 42" SIDES OF ELEVATOR THE HEIGHT OF THE CHARACTER.
MINIMUM 5" RADIUS CORNERS. THE ELEVATOR ENTRANCE SHALL HAVE CLEAR DIMENSIONS OF NOT LESS THAN 42 INCHES
MIN. MIN. 5 DOOR NOTE: WASHINGTON # : 8895

.
7. CHARACTER SPACING: CHARACTER SPACING SHALL BE MEASURED BETWEEN THE TWO CLOSEST POINTS OF WIDE BY 78 INCHES HIGH. THE ELEVATOR CAR SHALL HAVE A MINIMUM CLEAR DISTANCE BETWEEN WALLS OR BETWEEN
ELEVATORS & SPECIAL ACCESS (WHEELCHAIR) LIFTS (1124A.8) THE AUTOMATIC DOOR REOPENING
ADJACENT CHARACTERS, EXCLUDING WORD SPACES. SPACING BETWEEN INDIVIDUAL CHARACTERS SHALL BE 10% WALL AND DOOR OF NOT LESS THAN 80 INCHES BY 65 INCHES.
(C.B.C.-1124A) (a) SIDE OPENING DOOR (b) CENTER OPENING DOOR DEVICE IS ACTIVATED IF AN OBJECT ADDRESS:
(1124A.3.2) (1124A.3.2) PASSES THROUGH EITHER LINE "A" MIN. AND 35% MAX. OF CHARACTER HEIGHT.
CORRESPONDING LETTERING OR LINE "B".
GENERAL. 1590 BARTLETT LN

1548, 1554, 1560, 1566, 1572, 1578, 1584, & 1590 Bartlett
GRADE II BRAILLE RAISED 132" MIN. LINE "A" & LINE "B" REPRESENT THE 8. LINE SPACING: SPACING BETWEEN THE BASELINE OF SEPARATE LINES OF CHARACTERS WITHIN A MESSAGE SACRAMENTO, CA 95815
ELEVATORS PROVIDED IN COVERED MULTIFAMILY BUILDINGS SHALL BE ACCESSIBLE & COMPLY WITH THIS CHAPTER, ASME
(1124A.3.3.2) (1124A.8 #1) VERTICAL LOCATION OF THE DOOR SHALL BE 135% MIN. AND 170% MAX. OF THE CHARACTER HEIGHT. 24" X 84" 80" MIN.
A17.1 (SAFETY CODE FOR ELEVATORS AND ESCALATORS), TITLE 8 OF THE CALIFORNIA CODE OF REGULATIONS & ANY 60" MIN. 54" MIN.
REOPENING DEVICE NOT GURNEY
OTHER APPLICABLE SAFETY REGULATIONS OF OTHER ADMINISTRATIVE AUTHORITIES HAVING JURISDICTION.
REQUIRING CONTACT. 9. CHARACTER FORMAT: TEXT SHALL BE IN A HORIZONTAL FORMAT.
EXCEPTION: PRIVATE ELEVATORS SERVING ONLY ONE DWELLING UNIT. FLOOR SIGNAGE ON LANDING
(C.B.C.-1124A.1) JAMBS DETAIL
RAISED CHARACTERS & PICTORIAL SYMBOLS.
LOCATION. WHEN RAISED CHARACTERS ARE REQUIRED OR WHEN PICTORIAL SYMBOLS ARE USED ON SUCH SIGNS, THEY SHALL

65" MIN.
PASSENGER ELEVATORS SHALL BE LOCATED ON A MAJOR ACCESSIBLE ROUTE & PROVISIONS SHALL BE MADE TO ENSURE COMPLY WITH THIS SECTION. RAISED CHARACTERS & PICTORIAL SYMBOLS SHALL BE DUPLICATED IN BRAILLE
60" MIN.

THAT THEY REMAIN ACCESSIBLE AND USABLE AT ALL TIMES THAT THE BUILDING IS OCCUPIED. (C.B.C.-1124A.2) COMPLYING WITH SECTION 1143A.7. (C.B.C.-1143A.6)
(c) DOOR AT ANY LOCATION
1. CHARACTER TYPE: RAISED CHARACTERS ON SIGNS SHALL BE 132" MIN. ABOVE THEIR BACKGROUND. CHARACTERS

80" MIN.
(1124A.3.2)
SIZE OF CAB & CONTROL LOCATIONS. (C.B.C.-1124A.3) FLOOR LANDING NUMBER SHALL BE SANS SERIF UPPERCASE, AND SHALL NOT BE ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF
ON BOTH SIDES OF DOOR OTHER UNUSUAL FORMS.
GENERAL. JAMB
ELEVATORS SERVING COVERED MULTIFAMILY BUILDINGS SHALL BE SIZED TO ACCOMMODATE A WHEELCHAIR IN 2. CHARACTER HEIGHT: CHARACTER HEIGHT MEASURED VERTICALLY FROM THE BASELINE OF THE CHARACTER

D E V E L O P M E N T
ACCORDANCE WITH THIS SECTION. SHALL BE 5 8" MIN. & 2" MAX. BASED ON THE HEIGHT OF THE UPPERCASE LETTER "I".
(C.B.C.-1124A.3.1)
36" 3. CHARACTER FORMAT: CHARACTERS AND BRAILLE SHALL BE IN A HORIZONTAL FORMAT 42" W X 72" H
CAR INSIDE.
MIN.
THE ELEVATOR CAR SHALL BE DESIGNED TO COMPLY WITH ONE OF THE FOLLOWING: 4. PROPORTIONS: RAISED CHARACTERS ON SIGNS SHALL BE SELECTED FROM FONTS WHEN THE WIDTH OF THE
UPPERCASE LETTER "O" IS 60% MIN. AND 110% MAX. OF THE HEIGHT OF THE UPPERCASE LETTER "I".
1. DOOR CENTERED ON THE WALL: WHEN THE DOOR IS CENTERED ON THE CAR WALL, IT SHALL PROVIDE A CLEAR WIDTH
OF 42" MIN., AND THE CLEAR DISTANCE BETWEEN SIDE CAR WALLS SHALL BE 80" MIN. THE CLEAR DISTANCE BETWEEN THE 5. STROKE THICKNESS: STROKE THICKNESS OF THE UPPERCASE LETTER "I" SHALL BE 15% MAX. OF THE HEIGHT OF
BACK WALL AND THE RETURN PANEL SHALL BE 51" MIN. THE CLEAR DISTANCE BETWEEN THE BACK WALL AND THE INSIDE 36"
MIN. THE CHARACTER.
FACE OF THE DOOR SHALL BE 54" MIN.
6. CHARACTER SPACING: CHARACTER SPACING SHALL BE MEASURED BETWEEN THE TWO CLOSEST POINTS OF

GATEWAY
.NIM "27
2. DOOR NOT CENTERED ON THE WALL: WHEN THE DOOR IS NOT CENTERED ON THE CAR WALL, IT SHALL PROVIDE A CLEAR MIN. DIMENSIONS OF ELEVATOR CARS

VILLAGE-PHASE 2
CALL ADJACENT RAISED CHARACTERS WITHIN A MESSAGE, EXCLUDING WORD SPACES. WHEN CHARACTERS HAVE
WIDTH OF 36" MIN., AND THE CLEAR DISTANCE BETWEEN THE BACK WALL AND THE RETURN PANEL SHALL BE 51" MIN. THE (C.B.C. 2019) CHAPTER 12:
(FIG. 11A-7A) BUTTON RECTANGULAR CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED CHARACTERS SHALL BE 18" MIN. AND 4
CLEAR DISTANCE BETWEEN THE BACK WALL AND THE INSIDE FACE OF THE DOOR SHALL BE 54" MIN. INTERIOR ENVIRONMENT
TIMES THE RAISED CHARACTER STROKE WIDTH MAX. WHEN CHARACTERS HAVE OTHER CROSS SECTIONS, SPACING

.XAM "06 - .NIM "84

B BETWEEN INDIVIDUAL RAISED CHARACTERS SHALL BE 116" MIN. AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH
3. DOOR AT ANY LOCATION: AN ELEVATOR DOOR WITH 36" MIN. CLEAR WIDTH MAY BE INSTALLED AT ANY LOCATION IF ONE
MAX. AT THE BASE OF THE CROSS SECTIONS, AND 18" MIN. AT AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH
OF THE FOLLOWING IS MET: SECTION 1201, GENERAL :

APARTMENTS
SEE 5/8" MIN. 3/4" MIN. MAX. AT THE TOP OF THE CROSS SECTIONS. CHARACTERS SHALL BE SEPARATED FROM RAISED BORDERS AND
3.1 THE CAR INSIDE, WITH THE DOOR CLOSED, SHALL PROVIDE A TURNING CLEAR SPACE AT LEAST 60" IN DIAMETER DETAIL NUMBERAL BUTTON DECORATIVE ELEMENTS 3 8" MIN. SCOPE. THE PROVISIONS OF THIS CHAPTER SHALL GOVERN VENTILATION, TEMPERATURE CONTROL, LIGHTING, YARDS AND COURTS,
BELOW HEIGHT . DIA.,RAISED CONTROL SOUND TRANSMISSION, ROOM DIMENSIONS, SURROUNDING MATERIAL SAND RODENT PROOFING ASSOCIATED WITH THE INTERIOR SPACES OF

SACRAMENTO, CALIFORNIA
TO ALLOW FOR THE TURNING OF A WHEELCHAIR.

29"
1 1 PANEL, SEE (a) 7. LINE SPACING: SPACING BETWEEN THE BASELINES OF SEPARATE LINES OF RAISED CHARACTERS WITHIN A BUILDINGS. (SECTION - 1201.1)
PLACE STAR 8"± 32"
ALONGSIDE MESSAGE SHALL BE 135% MIN. AND 170% MAX. OF THE RAISED CHARACTER HEIGHT.
3.2 THE CLEAR DISTANCE BETWEEN CAR SIDE WALLS SHALL BE 54" MIN. THE CLEAR DISTANCE BETWEEN THE SECTION 1203, VENTILATION :
A
FRONT APPROACH

BACK WALL AND THE BACK PANEL AND THE RETURN PANEL SHALL BE 80" MIN. THE CLEAR DISTANCE BETWEEN THE MAIN EXIT 5 6 3
8"
MIN.
.

SIDE APPROACH

SEPARATION HANDRAIL 8. LOCATION: WHEN A TACTILE SIGN IS PROVIDED AT A DOOR, THE SIGN SHALL BE LOCATED ALONGSIDE THE DOOR
BACK WALL AND THE INSIDE FACE OF THE DOOR SHALL BE 80" MIN. FLOOR NUMBER
3 4 GENERAL. BUILDINGS SHALL BE PROVIDED WITH NATURAL VENTILATION IN ACCORDANCE WITH SECTION 1202.5, OR MECHANICAL

"5
AT THE LATCH SIDE. WHEN TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN SHALL
48" MAX. FOR

54" MAX. FOR

(C.B.C.-1124A.3.2) VENTILATION IN ACCORDANCE WITH THE CALIFORNIA MECHANICAL CODE. (SECTION - 1202.1)
.

1 2

48" MAX.
DOOR OPEN DOOR BE LOCATED ON THE INACTIVE LEAF. WHEN TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH TWO ACTIVE LEAFS,
1 1/2"
S B

32" MIN.
THE SIGN SHALL BE LOCATED TO THE RIGHT OF THE RIGHT HAND DOOR. WHEN THERE IS NO WALL SPACE AT THE
.

CLOSED NATURAL VENTILATION.

MIN.

A . (C.B.C.-1124A.3.3)
35"

EMERGENCY OPEN CLOSE

MIN. LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF DOUBLE DOORS, SIGNS SHALL BE LOCATED ON THE
ALARM ALARM STOP
EMERGENCY STOP NEAREST ADJACENT WALL. SIGNS CONTAINING TACTILE CHARACTERS SHALL BE LOCATED SO THAT A CLEAR FLOOR NATURAL VENTILATION OF AN OCCUPIED SPACE SHALL BE THROUGH WINDOWS, DOORS, LOUVERS OR OTHER OPENINGS TO THE OUTDOORS.
CAR CONTROL LOCATION. CL X (OCTAGONAL SYMBOL SPACE OF 18" X18" MIN., CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF ANY DOOR THE OPERATING MECHANISM FOR SUCH OPENINGS SHALL BE PROVIDED WITH READY ACCESS SO THAT THE OPENINGS ARE READILY
ABOVE FLOOR.

ELEVATOR FLOOR BUTTONS SHALL BE LOCATED WITHIN ONE OF THE REACH RANGES SPECIFIED IN SECTION 1138A.3. SHALL BE RAISED BUT SWING BETWEEN THE CLOSED POSITION AND 45° OPEN POSITION. WHEN PERMANENT IDENTIFICATION SIGNAGE IS CONTROLLABLE BY THE BUILDING OCCUPANTS. (SECTION - 1203.5)
EXCEPT FOR PHOTOELECTRIC TUBE BYPASS SWITCHES, EMERGENCY CONTROL, INCLUDING THE EMERGENCY STOP & THE "X" IS NOT) PROVIDED FOR ROOMS AND SPACES THEY SHALL BE LOCATED ON THE APPROACH SIDE OF THE DOOR AS ONE
ALARM, SHALL BE GROUPED IN OR ADJACENT TO THE BOTTOM OF THE PANEL & SHALL BE NO LOWER THAN 35" FROM THE VENTILATION AREA REQUIRED:
35" MIN.

ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALL BE LOCATED ON THE APPROACH SIDE OF THE
FLOOR. FOR MULTIPLE CONTROLS ONLY, ONE SET MUST COMPLY WITH THESE HEIGHT REQUIREMENTS. FLOOR BUTTONS DOOR AS ONE EXITS THE ROOM OR SPACE.
11A-7C- HOISTWAY & THE OPENABLE AREA OF THE OPENINGS TO THE OUTDOORS SHALL BE NOT LESS THAN 4 PERCENT OF THE FLOOR AREA BEING VENTILATED.
SHALL BE PROVIDED WITH VISUAL INDICATORS TO SHOW WHEN EACH CALL IS REGISTERED. THE VISUAL INDICATORS (a) ELEVATOR CONTROL (b) MAXIMUM INSTALLATION ELEVATOR ENTRANCES (SECTION - 1202.5.1)
SHALL BE EXTINGUISHED WHEN EACH CALL IS ANSWERED. (C.B.C.-1124A.3.3.1) PANEL DETAIL HEIGHTS ABOVE CAB FLOOR 9. HEIGHT: SIGNS WITH RAISED CHARACTERS SHALL BE LOCATED 48" MIN. ABOVE FINISH FLOOR, MEASURED FROM
(1124A.3.3.2) (1124A.3.3.1) THE BASELINE OF THE LOWEST BRAILLE CELLS AND 60" MAX. ABOVE FINISH FLOOR, MEASURED FROM THE BASELINE ADJOINING SPACES.
CAR CONTROL BUTTONS. ELEVATOR CONTROL PANEL WHERE ROOMS AND SPACES WITHOUT OPENINGS TO THE OUTDOORS ARE VENTILATED THROUGH AN ADJOINING ROOM, THE OPENING TO THE
OF THE HIGHEST LINE OF RAISED CHARACTERS.
ADJOINING ROOM SHALL BE UNOBSTRUCTED AND SHALL HAVE AN AREA OF NOT LESS THAN 8 PERCENT OF THE FLOOR AREA OF THE INTERIOR
PASSENGER ELEVATOR CAR CONTROLS SHALL HAVE A MIN. DIMENSION OF 3 4" & SHALL BE RAISED 18"± 132" ABOVE THE (FIG. 11A-7B)

D E B A R T O L O
EXCEPTION: TACTILE CHARACTERS FOR ELEVATOR CAR CONTROLS SHALL NOT BE REQUIRED TO COMPLY WITH THIS ROOM OR SPACE, BUT NOT LESS THAN 25 SQUARE FEET. THE OPENABLE AREA OF THE OPENINGS TO THE OUTDOORS SHALL BE BASED ON THE
SURROUNDING SURFACE. CONTROL BUTTONS SHALL BE ILLUMINATED, SHALL HAVE SQUARE SHOULDERS & SHALL BE

CL OF FARTHEST
SECTION. TOTAL FLOOR AREA BEING VENTILATED.
ACTIVATED BY A MECHANICAL MOTION THAT IS DETECTABLE. ALL CONTROL BUTTONS SHALL BE DESIGNATED BY A 5 8" MIN.

ENTRANCE
RAISED CHARACTERS AND STANDARD RAISED SYMBOL IMMEDIATELY TO THE LEFT OF THE CONTROL BUTTON. 10. PICTORIAL SYMBOL SIGNS (PICTOGRAMS): PICTORIAL SYMBOL SIGNS (PICTOGRAMS) SHALL BE ACCOMPANIED BY EXCEPTION:

CL OF CALL
CONTRACTED GRADE 2 BRAILLE SYMBOL SHALL BE LOCATED IMMEDIATELY BELOW THE NUMERAL, CHARACTER OR CAR CONTROL BUTTONS ELEVATOR FLOOR BUTTONS HEIGHT: EXTERIOR OPENINGS REQUIRED FOR VENTILATION SHALL BE ALLOWED TO OPEN INTO A SUNROOM WITH THERMAL ISOLATION OR A PATIO

BUTTON
A TEXT DESCRIPTION PLACED DIRECTLY BELOW THE PICTOGRAM. THE TEXT DESCRIPTION SHALL COMPLY WITH COVER PROVIDED THAT THE OPENABLE AREA BETWEEN THE SUNROOM ADDITION OR PATIO COVER AND THE INTERIOR ROOM SHALL HAVE AN
SYMBOL. A MIN. CLEAR SPACE OF 3 8" OR OTHER SUITABLE MEANS OF SEPARATION SHALL BE PROVIDED BETWEEN ROWS SHALL HAVE 3 4" (DIA.) 54" MAX. A.F.F. SECTIONS 1143A.6 & 1143A.7. THE OUTSIDE DIMENSION OF THE PICTOGRAM FIELD SHALL BE A MIN. OF 6" IN HEIGHT. AREA OF NOT LESS THAN 8 PERCENT OF THE FLOOR AREA OF THE INTERIOR ROOM OR SPACE, BUT NOT LESS THAN 20 SQUARE FEET
OF CONTROL BUTTONS. (FIG. 11A-7B). THE RAISED CHARACTERS & SYMBOLS SHALL BE WHITE ON A BLACK BACKGROUND. MIN. & TO BE RAISED FOR SIDE APPROACH ELEVATOR CHARACTERS AND BRAILLE SHALL NOT BE LOCATED IN THE PICTOGRAM FIELD. THE OPENABLE AREA OF THE OPENINGS TO THE OUTDOORS SHALL BE BASED ON THE TOTAL FLOOR AREA BEING VENTILATED.
.....THE CALL BUTTON FOR THE MAIN ENTRY FLOOR SHALL BE DESIGNATED BY A RAISED STAR AT THE LEFT OF THE FLOOR 1 "± 1 " ABOVE THE
8 32
(SECTION - 1202.5.1.1)
DESIGNATION. (C.B.C.-1124A.3.3.2) SURROUNDING SURFACE 48" MAX. A.F.F. BRAILLE CONTRACTED GRADE 2 BRAILLE SHALL BE USED WHEREVER BRAILLE IS REQUIRED IN OTHER PORTIONS OF
& SHALL BE ILLUMINATED FOR FRONT APPROACH ELEVATOR THESE STANDARDS. OPENINGS BELOW GRADE:
(1124A.3.3.2) (C.B.C.-1143A.7)
EMERGENCY TELEPHONE. 35" MIN. A.F.F. FOR BOTH

ARDEN
WHERE OPENINGS BELOW GRADE PROVIDE REQUIRED NATURAL VENTILATION, THE OUTSIDE HORIZONTAL CLEAR SPACE MEASURED
THE EMERGENCY TELEPHONE HANDSET SHALL BE POSITIONED NO HIGHER THAN 48" ABOVE THE FLOOR, & THE HANDSET 5 (1124A.3.3.1) DIMENSION & CAPITALIZATION: BRAILLE DOTS SHALL HAVE A DOMED OR ROUNDED SHAPE AND SHALL COMPLY WITH PERPENDICULAR TO THE OPENING SHALL BE ONE AND ONE-HALF TIMES THE DEPTH OF THE OPENING. THE DEPTH OF THE OPENING
CORD SHALL BE A 29" MIN. IN LENGTH. IF TELEPHONE SYSTEM IS LOCATED IN A CLOSED COMPARTMENT, THE 8" MIN.
SHALL BE MEASURED FROM THE AVERAGE ADJOINING GROUND LEVEL TO THE BOTTOM OF THE OPENING. (SECTION - 1202.5.1.2)
E TABLE 1143A.7.1. THE INDICATION OF AN UPPERCASE LETTER OF LETTERS SHALL ONLY BE USED BEFORE THE FIRST
COMPARTMENT DOOR HARDWARE SHALL CONFORM TO THE PROVISIONS OF SECTION 1138.4.4.
RAISED CHARACTERS TO A NC WORD OF SENTENCES, PROPER NOUNS AND NAMES, INDIVIDUAL LETTERS OF THE ALPHABET, INITIALS, AND
EMERGENCY INTERCOMMUNICATION SHALL NOT REQUIRE VOICE COMMUNICATION. (C.B.C.-1124A.3.4) 5 IST
.

LD ACRONYMS. (C.B.C.-1143A.7.1)
60"

BE WHITE ON A BLACK OPENINGS ON YARDS OR COURTS:

BACKGROUND AVE
HALL CALL BUTTONS. TR WHERE NATURAL VENTILATION IS TO BE PROVIDED BY OPENINGS ONTO YARDS OR COURTS, SUCH YARDS OR COURTS SHALL COMPLY WITH
CALL OPERATION BUTTONS AND KEYPADS SHALL BE LOCATED WITHIN ONE OF THE REACH RANGES SPECIFIED IN
(1124A.3.3.2) D= SECTION 1205. (SECTION - 1202.5.3)
DOOR DELAY FOR ELEVATORS
SECTION 1138A.3 MEASURED TO THE CENTERE LINE TO THE HIGHEST OPERABLE PART. BUTTONS SHALL HAVE SQUARE CORRESPONDING GRADE II ELEVATOR CAR CONTROL
BRAILLE OTHER VENTILATION AND EXHAUST SYSTEMS:
SHOULDERS, SHALL BE A MIN. OF 3 4" IN SIZE & SHALL BE RAISED 18" ± 132" ABOVE THE SURROUNDING SURFACE. BUTTON DETAIL BRAILLE DIMENSIONS (TABLE 1143A.7.1 & 11B-703.3.1)
(C.B.C.-1124A.4) (1124A.3.3.2)
VENTILATION AND EXHAUST SYSTEMS FOR OCCUPANCIES AND OPERATIONS INVOLVING FLAMMABLE OR COMBUSTIBLE HAZARDS OR OTHER
MINIMUM ILLUMINATION. MINIMUM IN INCHES CONTAMINANT SOURCES AS COVERED IN THE CALIFORNIA MECHANICAL CODE OR THE CALIFORNIA FIRE CODE SHALL BE PROVIDED AS
MEASUREMENT RANGE
THE MINIMUM ILLUMINATION AT THE CAR CONTROLS THRESHOLD AND THE LANDING WHEN THE CAR AND LANDING DOORS MAXIMUM IN INCHES REQUIRED BY BOTH CODES. (SECTION - 1202.6)
ARE OPEN SHALL NOT BE LESS THAN 5 FOOT-CANDLES (54 LX). (C.B.C.-1124A.5) REINFORCING FOR GRAB BARS @ BATHTUB, SHOWER & WATER CLOSET: DOT BASE DIAMETER 0.059 TO 0.063
(C.B.C. 2019 - 1134A) (1. ) DISTANCE BETWEEN 2 DOTS IN THE SAME CELL¹ 0.100
HALL LANTERN. SECTION 1204 LIGHTING:
A VISUAL & AUDIBLE SIGNAL SHALL BE PROVIDED AT EACH HOISTWAY ENTRANCE INDICATING TO THE PROSPECTIVE DISTANCE BETWEEN CORRESPONDING DOTS IN ADJACENT
BATHTUBS T= TOTAL TIME IN SECONDS (BEGINS WHEN THE 0.300 GENERAL.
PASSENGER THE CAR ANSWERING THE CALL & ITS DIRECTION OF TRAVEL AS FOLLOWS: CELLS¹ EVERY SPACE INTENDED FOR HUMAN OCCUPANCY SHALL BE PROVIDED WITH NATURAL LIGHT BY MEANS OF EXTERIOR GLAZED OPENINGS IN
ACCEPTABLE LANTERN IS VISIBLE FROM THE VICINITY OF HALL
2. REINFORCED WALLS FOR GRAB BARS : DOT HEIGHT 0.025 TO 0.037 ACCORDANCE WITH SECTION 1204.2 OR SHALL BE PROVIDED WITH ARTIFICIAL LIGHT IN ACCORDANCE WITH SECTION 1204.3. EXTERIOR GLAZED
CALL BUTTONS & AN AUDIBLE SIGNAL IS SOUNDED).
1. THE VISUAL SIGNAL FOR EACH DIRECTION SHALL BE A MIN. OF 2 12" HIGH BY 2 12" WIDE, AND VISIBLE FROM THE 13 OPENINGS SHALL OPEN DIRECTLY ONTO A PUBLIC WAY OR ONTO A YARD OR COURT IN ACCORDANCE WITH SECTION 1205. (SECTION - 1204.1)
A BATHTUB INSTALLED WITHOUT SURROUNDING WALLS SHALL PROVIDE REINFORCED AREAS FOR THE
UNACCEPTABLE

(1124A.7)
PROXIMITY OF THE HALL CALL BUTTON. DISTANCE BETWEEN CORRESPONDING DOTS FROM ONE 0.395 TO 0.400
"T" =TIME IN

INSTALLATION OF FLOOR-MOUNTED GRAB BARS. NATURAL LIGHT.

CELL DIRECTLY BELOW¹
SECONDS

9
2. THE AUDIBLE SIGNAL SHALL SOUND ONCE FOR THE "UP" DIRECTION & TWICE FOR THE "DOWN" DIRECTION OR OF A D= DISTANCE FROM A POINT IN THE LOBBY OR
WHERE A BATHTUB IS INSTALLED WITH SURROUNDING WALLS, GRAB BAR REINFORCEMENT SHALL BE LOCATED ON 1.MEASURED CENTER TO CENTER THE MINIMUM NET GLAZED AREA SHALL BE NOT LESS THAN 8 PERCENT OF THE FLOOR AREA OF THE ROOM SERVED. (SECTION - 1204.2)
CONFIGURATION WHICH DISTINGUISHES BETWEEN UP & DOWN ELEVATOR TRAVEL.... LANDING AREA, 60" DIRECTLY IN FRONT OF THE
EACH END OF THE BATHTUB, 32 INCHES TO 38 INCHES ABOVE THE FLOOR, EXTENDING A MINIMUM OF 24 INCHES 5 FARTHEST CALL BUTTON CONTROLLING THE CAR ADJOINING SPACES.
FROM THE FRONT EDGE OF THE BATHTUB TOWARD THE BACK WALL OF THE BATHTUB. THE GRAB BAR TO THE CENTERLINE OF ITS HOISTWAY DOOR.
3. THE CENTER LINE OF THE FIXTURE SHALL BE LOCATED A MIN. OF 6'-0" IN HEIGHT ABOVE FINISH FLOOR. REINFORCEMENT SHALL BE A MINIMUM OF 6 INCHES NOMINAL IN HEIGHT (FIGURE 11A-9G.) POSITION: BRAILLE SHALL BE POSITIONED BELOW THE CORRESPONDING TEXT IN A HORIZONTAL FORMAT, FLUSH
(1124A.7) FOR THE PURPOSE OF NATURAL LIGHTING, ANY ROOM IS PERMITTED TO BE CONSIDERED AS A PORTION OF AN ADJOINING ROOM WHERE
1 LEFT OR CENTERED. IF TEXT IS MULTI-LINES, BRAILLE SHALL BE PLACED BELOW THE ENTIRE TEXT. BRAILLE SHALL BE ONE-HALF OF THE AREA OF THE COMMON WALL IS OPEN AND UNOBSTRUCTED AND PROVIDES AN OPENING OF NOT LESS THAN ONE-TENTH OF
4. THE USE OF THE IN-CAR LANTERNS, LOCATED IN OR ON THE CAR DOORJAMBS, VISIBLE FROM THE PROXIMITY OF THE GRAB BAR REINFORCEMENT SHALL BE INSTALLED ON THE BACK WALL OF THE BATHTUB A MAXIMUM OF 6 INCHES 5 8 13 18 SEPARATED 3 8" MIN. AND 12" MAX. FROM ANY OTHER TACTILE CHARACTERS AND 3 8" MIN. FROM RAISED BORDERS AND THE FLOOR AREA OF THE INTERIOR ROOM OR 25 SQUARE FEET, WHICHEVER IS GREATER.
HALL CALL BUTTONS AND CONFORMING TO THE ABOVE REQUIREMENTS OF THIS SECTION, SHALL BE ACCEPTABLE. ABOVE THE BATHTUB RIM EXTENDING UPWARD TO AT LEAST 38 INCHES ABOVE THE FLOOR. GRAB BAR BACKING (D) =DISTANCE DECORATIVE ELEMENTS.
GRAPH OF TIMING EQUATION EXCEPTION:
SHALL BE INSTALLED HORIZONTALLY TO PERMIT THE INSTALLATION OF A 48-INCH GRAB BAR WITH EACH END A IN FEET (FIG. 11A-7D)
NOTE: THE USE OF ARROW SHAPES ARE PREFERRED FOR VISIBLE SIGNALS. OPENINGS REQUIRED FOR NATURAL LIGHT SHALL BE PERMITTED TO OPEN INTO A SUNROOM WITH THERMAL ISOLATION OR A PATIO COVER
MAXIMUM OF 6 INCHES FROM THE END WALLS OF THE BATHTUB. THE GRAB BAR REINFORCEMENT SHALL BE A EXCEPTION: BRAILLE PROVIDED ON ELEVATOR CAR CONTROLS SHALL BE SEPARATED 3 16" MIN. AND SHALL BE WHERE THE COMMON WALL PROVIDES A GLAZED AREA OF NOT LESS THAN ONE-TENTH OF THE FLOOR AREA OF THE INTERIOR ROOM OR 20
(C.B.C.-1124A.6) MINIMUM OF 6 INCHES NOMINAL IN HEIGHT. (C.B.C. 2016, 1134A.5.2) LOCATED DIRECTLY BELOW THE CORRESPONDING RAISED CHARACTERS OR SYMBOLS. (C.B.C.-1143A.7.2) SQUARE FEET WHICHEVER IS GREATER. (SECTION - 1204.2.1)

SHOWERS SYMBOLS OF ACCESSIBILITY: SYMBOLS OF ACCESSIBILITY AND THEIR BACKGROUND SHALL HAVE A NON-GLARE
FINISH. SYMBOLS OF ACCESSIBILITY SHALL CONTRAST WITH THEIR BACKGROUND WITH EITHER A LIGHT SYMBOL ON ARTIFICIAL LIGHT:
DOOR DELAY. (C.B.C.-1124A.7) MILESTONE:
4. REINFORCED WALLS FOR GRAB BARS : A DARK BACKGROUND OR A DARK SYMBOL ON A LIGHT BACKGROUND. SYMBOLS OF ACCESSIBILITY SHALL COMPLY ARTIFICIAL LIGHT SHALL BE PROVIDED THAT IS ADEQUATE TO PROVIDE AN AVERAGE ILLUMINATION OF 10 FOOTCANDLES OVER THE AREA OF THE THIRD CITY SUBMITTAL
HALL CALL. GRAB BAR REINFORCEMENT SHALL BE INSTALLED CONTINUOUS IN THE WALLS OF SHOWERS 32 INCHES TO 38 WITH THE FOLLOWING: ROOM AT A HEIGHT OF 30 INCHES ABOVE THE FLOOR LEVEL. (SECTION - 1204.3)
THE MIN. ACCEPTABLE TIME FROM NOTIFICATION THAT A CAR IS ANSWERING A CALL (LANTERN & AUDIBLE SIGNAL) INCHES ABOVE THE FLOOR. THE GRAB BAR REINFORCEMENT SHALL BE A MINIMUM OF 6 INCHES NOMINAL IN

COM-2213627 to COM-2213634
UNTIL THE DOORS OF THE CAR START TO CLOSE SHALL BE CALCULATED BY THE FOLLOWING EQUATIONS BUT SHALL HEIGHT. GLASS-WALLED SHOWER STALLS SHALL PROVIDE REINFORCEMENT FOR INSTALLATION OF PHOTOELECTRIC TUBE 1. INTERNATIONAL SYMBOL OF ACCESSIBILITY: "THE INTERNATIONAL SYMBOL OF ACCESSIBILITY" SHALL CONSIST
BE NO LESS THAN 5 SECONDS: (1. ). FLOOR-MOUNTED OR CEILING-MOUNTED GRAB BARS. (C.B.C. 2016, 1134A.6.4) BYPASS SWITCH OF A WHITE FIGURE ON A BLUE BACKGROUND. THE COLOR BLUE SHALL APPROXIMATE FS 15090 IN FEDERAL SECTION 1207
STANDARD 595C. (FIG. 11A-1A) INTERIOR SPACE DIMENSIONS: DRAWN: MH, NM
WHERE "T" IS THE TOTAL TIME IN SECONDS & "D" IS THE DISTANCE FROM A POINT IN THE LOBBY OR LANDING AREA 60" 6" 48" MIN. 6" 2. INTERNATIONAL SYMBOL OF TTY. (FIG. 11A-11C)
24" MINIMUM ROOM WIDTHS. CHECKED: JM
DIRECTLY IN FRONT OF THE FARTHEST CALL BUTTON CONTROLLING THAT CAR TO THE CENTERLINE OF ITS HOISTWAY MAX. MAX. HALL LANTERN CL OF HIGHEST 3. VOLUME CONTROL TELEPHONES. (FIG. 11A-11D) HABITABLE SPACES, OTHER THAN A KITCHEN, SHALL BE NOT LESS THAN 7 FEET IN ANY PLAN DIMENSION. KITCHENS SHALL HAVE A CLEAR
MIN.
DOOR (FIG. 11A-7D). FOR CARS WITH-IN CAR LANTERNS, "T" BEGINS WHEN THE LANTERN IS VISIBLE FROM THE VICINITY BUTTON 4. ASSISTIVE LISTENING SYSTEMS. (FIG. 11A-11E)
6" MAX.

PASSAGEWAY OF NOT LESS THAN 3 FEET BETWEEN COUNTER FRONTS AND APPLIANCES OR COUNTER FRONTS AND WALLS. PLOT DATE: Monday, October 24, 2022
OF HALL CALL BUTTONS & AN AUDIBLE SIGNAL IS SOUNDED. (C.B.C.-1124A.7.1) 5. CLEANER AIR SYMBOL. (CHAPTER 11B) (SECTION - 1207.1)
6. TOILET AND BATHING FACILITIES GEOMETRIC SYMBOLS. (SECTION 1127A.7)
MINIMUM CEILING HEIGHTS.
DOOR DELAY FOR CAR CALLS. CL OF (C.B.C.-1143A.8) E D A RC
6" MIN.

6" MIN.
32" MAX.

32" MAX.

32" MAX.

ER
38" MIN.

OCCUPIABLE SPACES, HABITABLE SPACES AND CORRIDORS SHALL HAVE A CEILING HEIGHT OF NOT LESS THAN 7 FEET 6 INCHES. BATHROOMS,
THE MIN. ACCEPTABLE TIME FOR THE DOOR TO REMAIN FULLY OPEN AFTER RECEIVING A CALL SHALL NOT BE LESS EMERGENCY TOILET ROOMS, KITCHENS, STORAGE ROOMS AND LAUNDRY ROOMS SHALL HAVE A CEILING HEIGHT OF NOT LESS THAN 7 FEET ABOVE THE
R Z JA

H
ST
THAN 5 SECONDS. (C.B.C.-1124A.7.2) BUTTON
72" MIN.

FINISH FLOOR.
MA B

IT E
RAISED CHARACTER AND BRAILLE EXIT SIGNS. TACTILE EXIT SIGNS SHALL BE REQUIRED AT THE FOLLOWING

R EG I
FA RA
LOCATIONS: EXCEPTIONS:

BA
DOOR JAMB MARKING.
X= 48" MAX. FOR FRONT APPROACH.

1. IN ONE- AND TWO-FAMILY DWELLINGS, BEAMS OR GIRDERS SPACED NOT LESS THAN 4 FEET ON CENTER SHALL BE PERMITTED TO PROJECT

CT
THE FLOOR LEVEL AT ALL ELEVATOR HOISTWAY ENTRANCES SHALL BE DESIGNED BY RAISED CHARACTERS PROVIDED CONTROL END (FOOT) WALL BACK WALL

RI
BACK SIDE NOT MORE THAN 6 INCHES BELOW THE REQUIRED CEILING HEIGHT.
(1124A.3.3.1)

No. C 15528
54" MAX. FOR SIDE APPROACH.

THIRD CITY SUBMITTAL 10/26/2022

ON BOTH JAMBS. CHARACTERS SHALL BE 2" IN HEIGHT LOCATED 48" MIN. ABOVE THE FINISH FLOOR. RAISED RAISED & HEAD END WALL(O.H.) EMERGENCY 1. EACH GRADE-LEVEL EXTERIOR DOOR THAT IS REQUIRED TO COMPLY WITH SECTION 1013.1, SHALL BE
35" MIN.

CHARACTERS PROVIDED ON BOTH JAMBS. SHALL BE 2" IN HEIGHT LOCATED 48" MIN. ABOVE THE FINISHED FLOOR, ... AND TELEPHONE IDENTIFIED BY A TACTILE EXIT SIGN WITH THE WORD, "EXIT". 2. IF ANY ROOM IN A BUILDING HAS A SLOPED CEILING, THE PRESCRIBED CEILING HEIGHT FOR THE ROOM IS REQUIRED IN ONE-HALF THE AREA
60" MAX. ABOVE THE FINISH FLOOR MEASURED FROM THE BASELINE OF THE HIGHEST LINE OF RAISED CHARACTERS. GRAB BAR REINFORCEMENT FOR ADAPTABLE BATHTUBS GRAB BAR REINFORCEMENT FOR ADAPTABLE SHOWERS THEREOF. ANY PORTION OF THE ROOM MEASURING LESS THAN 5 FEET FROM THE FINISHED FLOOR TO THE CEILING SHALL NOT BE INCLUDED IN Exp. 03/31/23
________
2. EACH EXTERIOR DOOR THAT IS REQUIRED TO COMPLY WITH SECTION 1013.1, AND THAT DIRECTLY TO A ANY COMPUTATION OF THE MINIMUM AREA THEREOF.
TA

IA
N

S
ON THE MAIN ENTRY LEVEL, A RAISED FIVE - POINTED STAR SHALL BE PLACED TO THE LEFT OF THE RAISED CHARACTER. GRADE-LEVEL EXTERIOR EXIT BY MEANS OF A STAIRWAY OR RAMP SHALL BE IDENTIFIED BY A TACTILE EXIT SIGN TE
O F CA L I F O R
3. THE HEIGHT OF MEZZANINES AND SPACES BELOW MEZZANINES SHALL BE IN ACCORDANCE WITH SECTION 505.2.
48" MAX.

WITH THE FOLLOWING WORDS AS APPROPRIATE:

(1124A.3.4)

THE OUTSIDE DIAMETER OF THE STAR SHALL BE 2" AND ALL POINTS SHALL BE OF EQUAL LENGTH. THE RAISED WATER CLOSETS
CHARACTERS AND THE STAR SHALL BE WHITE ON A BLACK BACKGROUND. CONTRACTED GRADE 2 BRAILLE, 2.1. "EXIT STAIR DOWN" 4. CORRIDORS CONTAINED WITHIN A DWELLING UNIT OR SLEEPING UNIT IN A GROUP R OCCUPANCY SHALL HAVE A CEILING HEIGHT OF NOT LESS
.2)

(1124A.3.3.1)
IN.

CONFORMING TO SECTION 1143A.7, SHALL BE PLACED BELOW THE CORRESPONDING RAISED CHARACTERS AND THE 2.2. "EXIT RAMP DOWN" THAN 7 FEET.
(112 IN.

2. REINFORCED WALLS FOR GRAB BARS : WHERE THE

4A.3
51" M

STAR. THE BRAILLE TRANSLATION FOR THE STAR SHALL STATE "MAIN". THE RAISED CHARACTERS SHALL COMPLY WITH 2.3. "EXIT STAIR UP"
54" M

WATER CLOSET IS NOT PLACED ADJACENT TO A 5. [OSHPD 1, 1R, 2, 3 & 5 I MINIMUM CEILING HEIGHTS SHALL COMPLY WITH SECTION 1224.4.10.
SECTION 1143.6. (FIG. 11A-7C) SIDE WALL CAPABLE OF ACCOMMODATING A GRAB 2.4. "EXIT RAMP UP"
PROJECT NO. 2021-051
(C.B.C.-1124A.8) BAR, THE BATHROOM SHALL HAVE PROVISIONS FOR 68" 6. [OSHPD 4] MINIMUM CEILING HEIGHTS SHALL COMPLY WITH SECTION 1227.8, (SECTION - 1207.2)
DOOR PROTECTIVE & REOPENING DEVICES. INSTALLATION OF FLOOR-MOUNTED, FOLDAWAY OR (112 TO 80" 3. EACH EXIT DOOR THAT IS REQUIRED TO COMPLY WITH SECTION 1013.1, AND THAT LEADS DIRECTLY TO A
4A.3 PROJECT PHASE .
DOORS CLOSED BY AUTOMATIC MEANS SHALL BE PROVIDED WITH A DOOR-REOPENING DEVICE THAT WILL FUNCTION TO SIMILAR ALTERNATIVE GRAB BARS. .2) GRADE-LEVEL EXTERIOR EXIT BY MEANS OF AN EXIT ENCLOSURE OR AN EXIT PASSAGEWAY SHALL BE FURRED CEILING:
IDENTIFIED BY A TACTILE EXIT SIGN WITH THE WORDS, "EXIT ROUTE". ANY ROOM WITH A FURRED CEILING SHALL BE REQUIRED TO HAVE THE MINIMUM CEILING HEIGHT IN TWO-THIRDS OF THE AREA THEREOF, BUT IN
STOP AND REOPEN A CAR DOOR & ADJACENT HOISTWAY DOOR IN CASE THE CAR DOOR IS OBSTRUCTED WHILE CLOSING. 40"MIN. NO CASE SHALL THE HEIGHT OF THE FURRED CEILING BE LESS THAN 7 FEET. (SECTION - 1207.2.1) SHEET TITLE
WHERE THE WATER CLOSET IS PLACED ADJACENT
THIS REOPENING DEVICE SHALL ALSO BE CAPABLE OF SENSING AN OBJECT OR PERSON IN THE PATH OF A CLOSING DOOR TO A SIDE WALL, REINFORCEMENT SHALL BE 12" 42" MIN. 4. EACH EXIT DOOR FROM AN INTERIOR ROOM OR AREA TO A CORRIDOR OR HALLWAY THAT IS REQUIRED TO ROOM AREA:
WITHOUT REQUIRING CONTACT FOR ACTIVATION AT THE NOMINAL 5" & 29" ABOVE THE FLOOR. INSTALLED ON BOTH SIDES OR ONE SIDE AND THE
BACK. IF REINFORCEMENT IS INSTALLED AT THE
MAX. COMPLY WITH SECTION 1013.1, SHALL BE IDENTIFIED BY A TACTILE SIGN WITH THE WORDS, "EXIT ROUTE". EVERY DWELLING UNIT SHALL HAVE NO FEWER THAN ONE ROOM THAT SHALL HAVE NOT LESS THAN 120 SQUARE FEET OF NET FLOOR AREA.
OTHER HABITABLE ROOMS SHALL HAVE A NET FLOOR AREA OF NOT LESS THAN 70 SQUARE FEET.
PUBLIC AREA
3/4" MIN.

5
RAISED CHARACTERS AND
5/8" MIN.

SYMBOLS SHALL BE WHITE ON A

CODE
BLACK BACKGROUND.

DOOR-REOPENING DEVICES SHALL REMAIN EFFECTIVE FOR A PERIOD OF NOT LESS THAN 20 SECONDS. AFTER SUCH AN BACK, IT SHALL BE INSTALLED BETWEEN 32 INCHES 26" 5. EACH EXIT DOOR THROUGH A HORIZONTAL EXIT THAT IS REQUIRED TO COMPLY WITH SECTION 1013.1, SHALL BE
32" MAX.

32" MAX.
38" MIN.

38" MIN.

EXCEPTION: KITCHENS ARE NOT REQUIRED TO BE OF A MINIMUM FLOOR AREA. (SECTION - 1207.3)
INTERVAL, THE DOORS MAY CLOSE IN ACCORDANCE WITH THE REQUIREMENTS OF ASME 17.1. AND 38 INCHES ABOVE THE FLOOR. THE GRAB BAR MIN. IDENTIFIED BY A SIGN WITH THE WORDS, "TO EXIT".
(C.B.C.-1124A.9) REINFORCEMENT SHALL BE A MINIMUM OF 6 INCHES (C.B.C.-1013.4)
NOMINAL IN HEIGHT. THE BACKING SHALL BE A
CORRESPONDING
GRADE II BRAILLE
REFERENCES
NUMERICAL HEIGHT

OPERATION & LEVELING. MINIMUM OF 40 INCHES IN LENGTH. 3 " MIN.

4

This set of plans and specifications must be

SEPARATION
8 " MIN.

BUTTON DIA.
THE ELEVATOR SHALL BE AUTOMATIC & BE PROVIDED WITH A SELF-LEVELING FEATURE THAT WILL AUTOMATICALLY REINFORCEMENT INSTALLED AT THE SIDE OF THE
ISSUED BY
SIDE WALL GRAB BAR
8 " MIN.

REAR WALL GRAB BAR

ELEVATOR -
5

BRING THE CAR TO THE FLOOR LANDINGS WITHIN A TOLERANCE OF 12" ± UNDER RATED LOADING TO ZERO LOADING WATER CLOSET SHALL BE INSTALLED 32 INCHES TO kept on the job at all times and it is unlawful to
3

(FIG. 11B-604.5.1) (FIG. 11B-604.5.2) GENERAL REQUIREMENTS

PLACE STAR
5 6
CONDITIONS. THIS SELF-LEVELING SHALL, WITHIN ITS ZONE, BE ENTIRELY AUTOMATIC AND INDEPENDENT OF THE 38 INCHES ABOVE THE FLOOR. THE
ALONGSIDE MAIN
EXIT FLOOR
NUMBER
3 4 make any changes or alterations from the Community Development Department
SHEET NO.
1 2 same without written permission from the
OPERATING DEVICE & SHALL CORRECT THE OVERTRAVEL OR UNDERTRAVEL. THE CAR SHALL ALSO BE MAINTAINED REINFORCEMENT SHALL BE INSTALLED A MAXIMUM S B
Ann Rosendale
By:

A9-1.4
OPEN CLOSE

APPROXIMATELY LEVEL WITH THE LANDING, IRRESPECTIVE OF LOAD. THE CLEARANCE BETWEEN THE CAR PLATFORM OF 12 INCHES FROM THE REAR WALL AND SHALL GRAB BAR REINFORCEMENT FOR WATER CLOSETS ALARM STOP Building Inspection Division.
X
SILL & THE EDGE OF THE HOISTWAY LANDING SHALL BE NO GREATER THAN 1 14" . EXTEND A MINIMUM OF 26 INCHES IN FRONT OF THE The approval of this plan and specification
ABV. FLR.
35" MIN.

(C.B.C.-1124A.10) WATER CLOSET. THE GRAB BAR REINFORCEMENT (b) ELEVATOR CONTROL PANEL DETAIL
SHALL NOT be held to permit or approve the on Jan 20, 2023
SHALL BE A MINIMUM OF 6 INCHES NOMINAL IN violation of any City Ordinance or State Law.
HEIGHT. (C.B.C. 2016, 1134A.7.2)
 NOTE:
ALL INFORMATION IS BASED ON C.B.C. 2019:

JOB COPY
DOORS: DOOR THRESHOLD DETAILS: (C.B.C.-1132A.4) NOTE: THESE CONDITIONS APPLY WATER CLOSET: (C.B.C.-SECTION 1134A)
(C.B.C.-1132A) (F.H.A.- CHAPTER 4) TO ALL COVERED DWELLING (INCLUDING F.H.A., CHAPTER 7)
UNITS.

ALL IDEAS, DESIGN ARRANGEMENTS AND PLANS INDICATED OR REPRESENTED BY THIS DRAWING ARE OWNED BY AND THE PROPERTY OF ARK ARCHITECTS, INC. AND WERE CREATED EVOLVED AND DEVELOPED FOR USE ON AND IN CONNECTION WITH THE SPECIFIED PROJECT. NONE OF SUCH IDEAS ARRANGEMENTS OR PLANS SHALL BE USED BY OR DISCLOSED TO ANY PERSON FIRM OR CORPORATION FOR ANY PURPOSE WHATSOEVER WITHOUT THE WRITTEN PERMISSION OF ARK ARCHITECTS, INC. ACCESSIBLE ROUTE WITHIN COVERED MULTIFAMILY
DWELLING UNITS:
AN ACCESSIBLE ROUTE SHALL BE PROVIDED
1. EXTERIOR LANDING OF IMPERVIOUS
CONSTRUCTION (E.G., CONCRETE, BRICK,
FLAGSTONE) SERVING PRIMARY ENTRY DOORS &
THRESHOLD @ THE PRIMARY ENTRY &
REQUIRED EXIT DOORS SHALL BE NO HIGHER
THAN 1/2".
WATER CLOSETS IN BATHROOMS OR POWDER ROOMS REQUIRED
TO BE ACCESSIBLE SHALL COMPLY WITH THE FOLLOWING :
1. FLOOR SPACE & LOCATION: 3'-0"
RE: ONE SIDE
WALL DETAIL 1'-0"
A R K
3'-4" REINFORCED AREA
THROUGH ALL ROOMS AND SPACES OF THE REQUIRED EXIT DOORS ARE LIMITED TO NOT MORE SECONDARY WATER CLOSET SHALL BE 48" IN CLEAR WIDTH. THE CLEAR FLOOR MIN. (12" W MIN. X
DWELLING UNIT. THE ACCESSIBLE ROUTE SHALL BE THAN 12" OF CHANGE IN HEIGHT BETWEEN FLOOR THRESHOLD @ THE SECONDARY EXTERIOR EXT. SWING SPACE SHALL EXTEND PAST THE FRONT EDGE OF THE WATER EQ. EQ. EDGE OF MAX.
PASS THROUGH THE PRIMARY ENTRY DOOR, AND SURFACES. DOORS INCLUDING SLIDING DOOR TRACKS, PRIMARY DOOR CLOSET AT LEAST 36"
REINFORCING
18" CLR. 40" L MIN.) 42" MIN. ARCHITECTS, INC.
EXCEPTION: THE 48" MIN. CLEAR WIDTH MAY BE REDUCED TO 36" GRAB BAR
SHALL CONNECT WITH ALL ADDITIONAL EXTERIOR CHANGES IN LEVEL SHALL COMPLY WITH SECTION SHALL BE NO HIGHER THAN 3/4". UNIT ENTRY/ (C.B.C.- FINISHED WING WALL,
FOR LAVATORIES, CABINETS, WING WALLS OR PRIVACY WALLS

MAX.
SECONDARY

2'-0"
DOORS, REQUIRED CLEAR FLOOR SPACES AT 1131A. EXIT DOOR 1132A.4.1) LOCATED IMMEDIATELY ADJACENT TO A WATER CLOSET WHICH WALL OR VANITY OR
KITCHEN APPLIANCES AND BATHROOM FIXTURES. 2. EXTERIOR LANDINGS OF PERVIOUS CHANGES IN HEIGHT @ INTERIOR DOOR 1:2 EXT. SLIDING Faramarz Jabbari, AIA

2'-93 4"
MAX.
TRANSITION EXTEND NO MORE THAN 24" IN DEPTH. BATHTUB EDGE OF C
L OF

3'-0"

MIN.

2'-9"
(C.B.C.-1130A) CONSTRUCTION(E.G., WOOD DECKING WITH SPACES) THRESHOLDS (E.G. FLOOR MATERIAL CHANGES SLOPE MAX. DOOR LAVATORY, 24"
RAMP REINFORCEMENT

MAX.
2'-2"

3/4"
(F.H.A.-P.12)

MIN.
AT DOOR THRESHOLDS) SHALL NOT EXCEED 1/2". INT. EXT. WATER CLOSETS SHALL BE LOCATED WITHIN BATHROOMS IN A

MAX.

38"
SHALL BE THE SAME LEVEL AS THE INTERIOR

1/4"
MAX. DEPTH.

MAX.
COMPLYING WITH PERVIOUS MIN.

2'-8"
LANDING, EXCEPT THAT SECONDARY EXTERIOR MANNER THAT PERMITS A GRAB BAR TO BE INSTALLED ON

MAX.

MAX.
CHANGES IN LEVEL ON ACCESSIBLE ROUTES: C.B.C.- (1131A.1 - SURFACE (F.H.A.-P.7.44)

3/4"
2240

1/2"
MAX.
1/2"
AT LEAST ONE SIDE OF THE FIXTURE.
DOORS MAY HAVE NO MORE THAN 12" OF CHANGE IN THRESHOLD SHALL COMPLY WITH THE 1122A.2)

MAX.

MIN.
3'-0"
HEIGHT BETWEEN FLOOR SURFACES. CHANGES IN FOLLOWING: 3'-412" R.O. Faraday Road

1/2"
CHANGES IN LEVEL NOT EXCEEDING 1 2".

MAX.
THE CENTERLINE OF THE WATER CLOSET SHALL BE 17" MIN. TO 18"
LEVEL SHALL COMPLY WITH SECTION 1131A. 1) THRESHOLD WITH THE CHANGES IN HEIGHT

4"
ABRUPT CHANGES IN LEVEL ALONG ANY ACCESSIBLE IMPERVIOUS MAX. FROM A GRAB BAR WALL OR PARTITION. IN LOCATIONS WHERE 36"X48" MIN. ELEVATION FOR BACKING SIDE ELEVATION
OF NOT MORE THAN 1/4" MAY BE VERTICAL. (C.B.C.- (C.B.C. 1132A.4 #3 & C.B.C.- WATER CLOSETS ARE ADJACENT TO NON-GRAB BAR WALLS,
ROUTE SHALL NOT EXCEED 12". SURFACE CLR. SPACE 18" CLR. (C.B.C.-1134A.7.2)
3. SECONDARY EXTERIOR DOORS ONTO DECKS, IMPERVIOUS SURFACE 1132A.4.1) 1132A.4.1 & VANITIES, LAVATORIES OR BATHTUBS, THE CENTERLINE OF THE
WHEN CHANGES IN LEVEL DO OCCUR, THEY SHALL BE F.H.A.-P 4.13) Carlsbad, California
PATIOS OR BALCONY SURFACES CONSTRUCTED OF 2) THRESHOLD WITH THE CHANGE IN HEIGHT 1/8" SLOPE MAX. (F.H.A.- FIXTURE SHALL BE A MINIMUM OF 18" FROM THE OBSTACLE. F.H.A.-
BEVELED WITH THE SLOPE NO GREATER THAN 1 UNIT 4'-0" 15 3/4" 18"
IMPERVIOUS MATERIALS (E.G., CONCRETE, BRICK, BETWEEN 1/4" & 3/4" SHALL BE BEVELED WITH P/FT. (F.H.A.-P.4.11) P 4.14) P .7 36" MIN. 92008
VERT. IN 2 UNITS HORIZ. 2. REINFORCED WALLS FOR GRAB BARS. MIN. * MIN.
FLAGSTONE) MAY HAVE A MAX. CHANGE IN HEIGHT THE SLOPE NO GREATER THAN 1 UNIT VERTICAL GRAB BAR Tel: (858) 792-5997
CHANGES IN LEVEL NOT EXCEEDING 14" MAY BE WHERE THE WATER CLOSET IS NOT PLACED ADJACENT TO A SIDE REINFORCED AREA
IN 2 UNITS HORIZONTAL (50 % SLOPE). PRIMARY ENTRY/ EXIT SECONDARY EXIT SWING SECONDARY EXIT SLIDING DR./ GRAB BAR
VERTICAL. FROM THE INTERIOR LANDING OF 4". WALL CAPABLE OF ACCOMMODATING A GRAB BAR, THE BATHROOM 17"-18" EQ. (6"W MIN. X 40"L MIN.) Fax: (858) 792-5858
(C.B.C.- 1132A.4.1) DR./ IMPERVIOUS DR./ IMPERVIOUS SURFACE PERVIOUS SURFACE (FOLD AWAY) FINISHED WALL,
CHANGES GREATER THAN 12". CHANGES IN HEIGHT GREATER THAN 12" SHALL BE SHALL HAVE PROVISIONS FOR INSTALLATION OF FLOOR-MOUNTED,
ACCOMPLISHED BY MEANS OF A RAMP. SURFACE N.T.S. N.T.S. FOLDAWAY OR SIMILAR ALTERNATIVE GRAB BARS. REQUIRED CLEARANCE VANITY OR EDGE
CHANGES IN LEVEL GREATER THAN 12" SHALL BE WALL OR
N.T.S. WHERE THE WATER CLOSET IS PLACED ADJACENT TO A SIDE WALL, FLOOR SPACE. & LANDING OF LAVATORY
MADE BY MEANS OF A RAMP, ELEVATOR OR REINFORCEMENT SHALL BE INSTALLED ON BOTH SIDES OR ONE
EDGE OF
5. IN BUILDING CONTAINING COVERED MULTIFAMILY THE FINISHED SURFACE OUTSIDE THE PRIMARY (C.B.C.-1134A.7 #1& BATHTUB

3'-2"
PLATFORM (WHEELCHAIR) LIFT. SECONDARY ONE SIDE WALL.

MIN.

2'-8"
MAX.
SIDE AND THE BACK. 09/12/2022
DWELLING UNITS, THE FLOOR OR LANDING ENTRY DOOR MAY BE SLOPED @ 1/8" MAX. P/FT. F.H.A. - P.7.43) (C.B.C.-1134A.7.2)
(C.B.C.-1131A) EXT. SLIDING IF REINFORCEMENT IS INSTALLED AT THE BACK, IT SHALL BE
INDICATES DIRECTION A SECOND CITY SUBMITTAL
IMMEDIATELY OUTSIDE THE ENTRY MAY BE SLOPED (F.H.A. - P.4.11) DOOR INSTALLED BETWEEN 32" AND 38" ABOVE THE FLOOR. THE GRAB PLAN
UP TO 14" PER FOOT, IN A DIRECTION AWAY FROM THE BAR REINFORCEMENT SHALL BE A MINIMUM OF 6" NOMINAL IN OF APPROACH
10/26/2022
PRIMARY ENTRY DOORS AND REQUIRED EXIT PRIMARY ENTRANCE OF THE DWELLING UNIT FOR SECONDARY HEIGHT. THE BACKING SHALL BE A MINIMUM OF 40" IN LENGTH. B
WHEN MEASURING THE DISTANCE BETWEEN THE THIRD CITY SUBMITTAL
DOORS. DRAINAGE. FLUSH (C.B.C. 1132A.4.2) EXT. SWING REINFORCEMENT INSTALLED AT THE SIDE OF THE WATER CLOSET 18" CLR. REINFORCED AREA ELEVATION
FLOOR INSIDE AND THE OUTSIDE SURFACE, THE
THE REQUIREMENTS OF SECTIONS 1126A.3 SHALL (C.B.C.-1132A.4) PRIMARY DOOR SHALL BE INSTALLED 32"TO 38" ABOVE THE FLOOR. (12" W MIN. X
INTERIOR FLOOR LEVEL MUST BE CALCULATED THE REINFORCEMENT SHALL BE INSTALLED A MAXIMUM EDGE OF 3
APPLY TO MANEUVERING CLEARANCES AT THE SIDE (C.B.C.- UNIT ENTRY/ (C.B.C.- 37"L MIN.) ----
FROM THE FINISHED FLOOR AND NOT FROM THE OF 12" FROM THE REAR WALL AND SHALL EXTEND A MINIMUM OF 26" REFER TO BASIS OF REINFORCING
OF THE DOOR EXPOSED TO COMMON OR PUBLIC MANEUVERING CLEARANCES AT DOORS: 1132A.4.1) EXIT DOOR 1132A.4.1) FINISHED
SUBFLOOR. IF CARPET IS TO BE INSTALLED, THE IN FRONT OF THE WATER CLOSETS THE GRAB BAR REINFORCEMENT DESIGN NOTES CL OF 3'-41 2" R.O.
USE SPACES (E.G. ENTRY OR EXIT DOORS WHICH CL WALL 4
MEASUREMENT SHOULD BE CALCULATED W/ THE TRANSITION PERVIOUS SHALL BE A MINIMUM OF 6" NOMINAL IN HEIGHT.(C.B.C.-1134A.7 REINFORCEMENT ----
OPEN FROM THE COVERED MULTIFAMILY DWELLING F.H.A. P.6.5 FOR BACKING

MAX.
GENERAL. RAMP INT. EXT.

MAX.
FULL COMPRESSED CARPET AND, IF PRESENT, #1& 2)

3'-0"
PERVIOUS

MAX.

3/4"
SURFACE
IN.

2'-9"
GRAB BAR

3/4"
UNIT UNTO A CORRIDOR, HALLWAY OR LOBBY, OR THE FLOOR OR LANDING ON THE DWELLING UNIT SIDE OF THE COMPLYING WITH REINFORCING 23 17"-18" 36" MIN. GRAB BAR
THE PAD. M
DIRECTLY TO THE OUTSIDE). PRIMARY ENTRY DOOR AND ANY REQUIRED EXIT DOOR SHALL SURFACE BEHIND WATER 40" /4" 5/8 (FOLD AWAY) 5 ----
43

MAX.

MAX.
1/2"
(F.H.A. - P. 4.11) C.B.C.- (1131A.1 - " " (F.H.A.-P.6.5)
36

1/2"
(C.B.C.-1132A.1) HAVE A MINIMUM LENGTH OF NOT LESS THAN 44", CLOSET

MAX.
1122A.2)

12"
WIDTH & HEIGHT OF INTERIOR DOOR & SECONDARY ( F.H.A.-P 4.14) SEAT HEIGHT. ELEVATION FINISHED WALL, 6 ----

MAX.
SECTION 1126A.3 SHALL APPLY TO MANEUVERING CLEARANCES IMPERVIOUS
EXTERIOR DOORS. MAX. ALLOWABLE HEIGHT: (DIFFERENCE WATER CLOSET SEAT HEIGHT SHALL BE (15" ) TO (19")

4"
AT THE SIDE OF THE DOOR EXPOSED TO COMMON OR PUBLIC SURFACE CL 3'-11 2" R.O. VANITY OR EDGE
USE SPACES. BETWEEN INT. & EXT. FLOOR LEVEL ) ABOVE FINISH FLOOR. GRAB BAR GRAB BAR OF LAVATORY 7
* F.H.A. FOR BACKING ----
DOORS SHALL COMPLY WITH THE FOLLOWING: CONSTRUCTION MATERIAL (F.H.A., P.7.60 & ANSI 1003.11.7.4 P.91) 33" MIN. (C.B.C.-
MANUEVERING CLEARANCES AT INTERIOR DOORS SHALL (P 6.7) FINISHED WALL,
1. DOORS SHALL NOT BE LESS THAN 6'-8" IN HEIGHT. DOOR A.F.F. 15 3/4" 18 3/4" 1134A.7.2) 42" MIN. GRAB BAR
PROVIDE A MINIMUM LENGTH ON BOTH SIDES OF THE DOOR OF PERVIOUS IMPERVIOUS BASIS OF DESIGN NOTES: VANITIES OR 8
GRAB BAR * MIN. (F.H.A.-P.6.5) ----
AT LEAST 42" MEASURED AT A RIGHT ANGLE TO THE PLANE PRIMARY SECONDARY EXIT SLIDING PRIMARY ENTRY/ EXIT DR./ SECONDARY EXIT SWING DR./ EDGE OF FINISHED
2. SWING DOORS SHALL PROVIDE A NET CLEAR OF THE DOOR IN ITS CLOSED POSITION. 0" 1/2" 1) FOLD-AWAY GRAB BAR MOUNTING PLATE SHOWN (FOLD AWAY) LAVATORIES,

8 1/4"
OPENING WIDTH OF NOT LESS THAN 32", MEASURED ENTRY DOOR DR./ IMPERVIOUS SURFACE PERVIOUS SURFACE PERVIOUS SURFACE IS 4 3/4" WIDE. PLEASE NOTE THAT ANY WIDER PLATE WALL
24" MAX. DEPTH ONE SIDE WALL. 9 ----
WITH THE DOOR OR DOORS POSITIONED AT AN EXCEPTION: A 39" LENGTH IS ACCEPTABLE AT INTERIOR DOORS SECONDARY EXT. N.T.S. N.T.S. N.T.S. WILL REQUIRE MODIFICATIONS TO THE MIN. (C.B.C.-1134A.7 #1)
1/2" 4" FOLD-UP SIDEWISE WALL OR OF WALL. PLAN
ANGLE OF 90° FROM THE CLOSED POSITION. WHEN A MINIMUM CLEAR OPENING WIDTH OF 34" IS PROVIDED. DOOR EXIT (ONTO DIMENSIONS SHOWN. ROTATING SAFETY BAR EDGE OF
(C.B.C.-1132A.5.1) (F.H.A.-P.7.44)
DECK, PATIO OR 2) MIN. DIMENSIONS SHOWN WHICH ARE GREATER 36" MAX. A.F.F. BATHTUB ARIZONA # : 27259
3. SWINGING DOORS SHALL BE CAPABLE OF STRIKE EDGE MANEUVERING SPACE AT DOORS: BALCONY) THAN CODE REQUIREMENTS ARE DUE TO BY BARRIER FREE
OPENING AT LEAST 90° CONSTRUCTABILITY CONCENS REGARDING BACKING ONE SIDE WALL. CALIFORNIA # : C15528
THE WIDTH OF THE LEVEL AREA ON THE SIDE TO (F.H.A.-P.4.11) LIVING OR EQUAL PLAN
& POTENTIAL CONFLICTS BETWEEN ELEMENTS. (C.B.C.-1134A.7 #1)
WHICH THE DOOR SWINGS SHALL BE EXTEND 18" PAST COLORADO # : 304356
4. A NOMINAL 32" CLEAR OPENING PROVIDED BY A THE STRIKE EDGE FOR ALL DOORS.THE WIDTH OF THE
STANDARD 6'-0" WIDE SLIDING PATIO DOOR 18" CLR. OREGON # : 5318
LEVEL AREA AT THE EXTERIOR SIDE OF THE PRIMARY
ASSEMBLY IS ACCEPTABLE. ENTRY DOOR AND ANY REQUIRED EXIT DOORS SHALL NEVADA # : 2838
COMPLY WITH SECTION 1126A.
5. A PAIR OF DOORS, MANUAL OR AUTOMATIC, MUST TEXAS # : 16533
NOTES:
HAVE AT LEAST ONE LEAF WHICH PROVIDES A 1). SEE SECTION 1134A FOR BATHROOMS THAT ARE UTAH # : 7288093-0301
CLEAR WIDTH OF NOT LESS THAN 32", MEASURED REQUIRED TO BE ACCESSIBLE LAVATORIES, VANITIES, MIRRORS & TOWEL FIXTURES: BATHTUBS, CLEAR FLOOR SPACE & GRAB BARS: SHOWERS: (C.B.C.-1134A.6)
KITCHENS: (C.B.C.-1133A) WASHINGTON # : 8895
WITH THE DOOR POSITIONED AT ANGLE OF 90° FROM 2). 24" IS PREFERRED FOR STRIKE EDGE CLEARANCE. (INCLUDING F.H.A. REQUIREMENTS) (C.B.C.-1134A.8) (INCLUDING F.H.A. & ANSI REQUIREMENTS)
ITS CLOSED POSITION. (C.B.C.-1132A.5.2)
(C.B.C.-1132A.3) FLOOR SPACE. CLEARANCE;
SMOOTH SURFACE. ADDRESS:
BATHROOMS OR POWDER ROOMS REQUIRED TO BE KITCHENS: THERE SHALL BE A MINIMUM CLEAR FLOOR SPACE 48" PARALLEL BY A CLEARANCE IN FRONT OF BATHTUBS EXTENDING
SWINGING DOOR OR GATE SURFACES WITHIN 10" OF THE FINISH REPOSITIONABLE COUNTERTOPS. 1. SIZE WHEN ONE OR MORE SHOWER STALLS ARE
ACCESSIBLE SHALL HAVE AT LEAST ONE ACCESSIBLE KITCHENS SHALL BE ON AN ACCESSIBLE ROUTE. 30" PERPENDICULAR TO THE SIDE OF A BATHTUB OR BATHTUB- 1590 BARTLETT LN
FLOOR OR GROUND MEASURED VERTICALLY SHALL HAVE A REPOSITIONABLE COUNTERTOPS SHALL BE PROVIDED IN A THE LENGTH OF THE BATHTUB & 30" MIN. IN DEPTH PROVIDED WITHIN THE SAME DWELLING UNITS, AT 42"

1548, 1554, 1560, 1566, 1572, 1578, 1584, & 1590 Bartlett
DOORS TO THE CABINET (C.B.C.-1133A.1) SHOWER COMBINATION. THE CONTROLS SHALL BE ON THE WALL AT
SMOOTH SURFACE ON THE PUSH SIDE EXTENDING THE FULL LAVATORY. MINIMUM OF 5% OF THE COVERED MULTIFAMILY DWELLING SHALL BE PROVIDED. WHERE A PERMANENT SEAT IS LEAST ONE SHOWER STALL COMPLY WITH ONE OF THE MIN. SACRAMENTO, CA 95815

K-T13140-3B
PINSTRIPE
FAUCETS
BRASS
CLEAR FLOOR SPACE. THE FOOT OF THE BATHTUB. THE EDGE OF THE CLEAR FLOOR SPACE
BENEATH THE LAVATORY

MAX.
WIDTH OF THE DOOR OR GATE. PARTS CREATING HORIZONTAL WHERE MIRRORS AND TOWEL FIXTURES ARE PROVIDED, UNITS. PROVIDED, THE CLEARANCE SHALL BE EXTEND 12" FOLLOWING REQUIREMENTS:
1. A CLEAR FLOOR SPACE AT LEAST 30" X 48" SHALL BE FLUSH WITH THE CONTROL WALL SURFACE.

6"
SHALL BE REMOVABLE OR REPOSITIONABLE COUNTERTOPS SHALL COMPLY WITH THE

MAX.*
OR VERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN AT LEAST ONE OF EACH SHALL BE ACCESSIBLE. MIN. BEYOND THE WALL AT THE HEAD END OF THE
THE AREA UNDER A LAVATORY, LOCATED AT THE CONTROL END OF

VITREOUS CHINA
PENNINGTON
LAVATORY
K-2196-8
THAT ALLOWS A PARALLEL APPROACH BY A PERSON IN A

34"
MIN.
1/16" OF THE SAME PLANE AS THE OTHER AND BE FREE OPENABLE TO PROVIDE THE FOLLOWING: SEAT

29"
(C.B.C.-1134A.8) 1.1. THE SHOWER STALL SHALL MEASURE AT LEAST

MIN.
LEVEL FLOOR OR LANDING:

27"
WHEELCHAIR SHALL BE PROVIDED AT THE RANGE OR 1. SINKS AND WORK SURFACES SHALL BE DESIGNED TO THE TUB, MAY BE INCLUDED IN THE CLEAR FLOOR SPACE PROVIDED BATHTUB. (ANSI 2003-607.2- P. 54)
OF SHARP OR ABRASIVE EDGES. CAVITIES CREATED BY ADDED REQUIRED UNOBSTRUCTED 42" WIDE BY 48" DEEP WITH AN ENTRANCE
THE LAVATORY IS 19" MAXIMUM DEEP.

MIN.
THE FLOOR OR LANDING ON EACH SIDE OF A DOOR COOKTOP. ENABLE REPOSITIONING TO A MINIMUM HEIGHT OF 28".

MIN.
KICK PLATES SHALL BE CAPPED. OPENING OF AT LEAST 36"; OR

48"
KNEE AND TOE SPACE.

9"
SHALL BE LEVEL. 2. BASE CABINETS DIRECTLY UNDER SINKS AND WORK CABINETS UNDER LAVATORIES AND TOILETS SHALL NOT ENCROACH SEATS;
EXCEPTIONS: 1.2. THE SHOWER STALL SHALL MEASURE AT LEAST
PRIMARY ENTRY DOORS, REQUIRED EXIT DOORS OR 1) LOCATION. 8" 6" (C.B.C.-1134A.8#4.3) 2. A CLEAR FLOOR SPACE AT LEAST 30"X48" THAT SURFACES SHALL BE REMOVABLE. INTO THE CLEAR FLOOR SPACE. (C.B.C. 1134A.5.1) IF THE PLAN INDICATE A PERMANENT SEAT AT THE HEAD
1. AUTOMATIC DOORS. 30" DEEP BY 60" WIDE WITH AN ENTRANCE
(ANSI - ALLOWS EITHER A PARALLEL OR FORWARD APPROACH 2. REINFORCED WALLS FOR GRAB BARS. END OF THE BATHTUB, THE SEAT SHALL BE PROVIDED AS
SECONDARY EXTERIOR DOORS WITH CHANGES IN 2. TEMPERED GLASS DOORS WITHOUT STILES AND HAVING VANITIES AND LAVATORIES SHALL BE INSTALLED WITH MIN. MAX. 606.3 #1) * TOP OF LAVATORY'S 3. THE SIDES OF ADJACENT CABINETS AND THE BACK OPENING OF AT LEAST 60". A WATER CLOSET
SHALL BE PROVIDED AT THE KITCHEN SINK AND ALL OTHER WALL, WHICH MAY BECOME EXPOSED TO MOISTURE OR FOOD A BATHTUB INSTALLED WITHOUT SURROUNDING WALLS SHALL
HEIGHT BETWEEN THE INTERIOR SURFACE OF FLOOR A BOTTOM RAIL OR SHOE WITH THE TOP LEADING EDGE THE CENTERLINE OF THE FIXTURE A MIN. OF 18" 17" RIM A.F.F. FOLLOWS: MAY PROJECT A MAXIMUM OF 12" INTO THE
FIXTURES OR APPLIANCES INCLUDING THE OVEN, HANDLING WHEN A COUNTERTOP IS LOWERED, SHALL BE PROVIDE REINFORCED AREAS FOR THE INSTALLATION OF
LEVEL & THE EXTERIOR SURFACE OR FLOOR LEVEL TAPERED AT 60 DEGREES MINIMUM FROM THE HORIZONTAL. HORIZONTALLY FROM AN ADJOINING WALL OR FIXTURE MIN. THE HEIGHT OF BATHTUB SEATS SHALL BE 17"-19" ABOVE OPENING, PROVIDED THAT A MINIMUM OF 36"
DISHWASHER, REFRIGERATOR/FREEZER AND TRASH FLOOR-MOUNTED GRAB BARS.
3. DOORS OR GATES THAT DO NOT EXTEND TO WITHIN 10" KNEE & TOE SPACE: CONSTRUCTED OF DURABLE, NONABSORBENT MATERIALS
THE BATHROOM FLOOR. REMOVABLE IN-TUB SEATS SHALL CLEAR SPACE IS MAINTAINED BETWEEN THE 36"
SHALL COMPLY WITH THE FOLLOWING: TO ALLOW FOR FORWARD APPROACH. WHEN PARALLEL SIDE ELEVATION COMPACTOR. APPROPRIATE FOR SUCH USES.
OF THE FINISH FLOOR. (C.B.C.-1132A.9) (C.B.C.-1134A.8 #4, 11B-1D & BE 15"-16" IN DEPTH & CAPABLE OF SECURE PLACEMENT. WATER CLOSET AND THE SHOWER WALL OR; MIN.
APPROACH IS PROVIDED, LAVATORIES SHALL BE 3. A CLEAR FLOOR SPACE AT LEAST 30"X48" THAT 4. FINISHED FLOORING SHALL BE EXTENDED TO THE WALL WHERE A BATHTUB IS INSTALLED WITH SURROUNDING WALLS, GRAB CLEAR
F.H.A.- P.52) BAR REINFORCEMENT SHALL BE LOCATED ON EACH END OF THE PERMANENT SEATS SHALL BE 15" MIN. DEPTH & SHALL 1.3. OTHER SHOWER STALL CONFIGURATIONS SHALL
INSTALLED WITH THE CENTERLINE OF THE FIXTURE A MIN. ALLOWS EITHER A PARALLEL OR A FORWARD APPROACH BENEATH THE SINK AND WORK SURFACE. FLOOR
BATHTUB, 32" TO 38" ABOVE THE FLOOR, EXTENDING A MINIMUM OF 24" MEASURE AT LEAST 36" DEEP BY 60" WIDE WITH
OF 24" HORIZONTALLY FROM AN ADJOINING WALL OR SHALL BE PROVIDED AT THE WORK SURFACE REQUIRED BY EXTEND FROM THE BACK WALL TO OR BEYOND THE AN ENTRANCE OPENING OF AT LEAST 36" INCHES SPACE
SECTION 1133A.4. FROM THE FRONT EDGE OF THE BATHTUB TOWARD THE BACK WALL
FIXTURE. ADJOINING EXCEPTIONS: OUTER EDGE OF THE BATHTUB & POSITIONED AT THE WHEN A WALL IS INSTALLED ON THE OPENING
DOOR SIGNAL DEVICES: 17" 4. THE CENTERLINE OF THE 30"X48" CLEAR FLOOR 1. STONE, CULTURED STONE AND TILED COUNTERTOPS OF THE BATHTUB. THE GRAB BAR REINFORCEMENT SHALL BE A
THE TOP OF THE FIXTURE RIM SHALL BE A MAX. OF 34" WALL HEAD END OF THE BATHTUB. SIDE. (C.B.C.-1134A.6.#1) FIGURE "A"

D E V E L O P M E N T
SPACE PROVIDED FOR PARALLEL OR FORWARD APPROACH MAY BE USED WITHOUT MEETING THE REPOSITIONING MINIMUM OF 6" NOMINAL IN HEIGHT.
EVERY PRIMARY ENTRANCE TO A COVERED ABOVE THE FINISHED FLOOR. (C.B.C.-1134A.8 #1) MIN. (C.B.C.- (ANSI 2003-610.2- P.62)
SHALL BE ALIGNED WITH THE CENTERLINE OF THE WORK REQUIREMENTS. GRAB BAR REINFORCEMENT SHALL BE INSTALLED ON THE
MULTIFAMILY DWELLING UNIT SHALL BE PROVIDED 1127A.3 #1) 2. SLOPE

MIN.
BACK WALL OF THE BATHTUB A MAXIMUM OF 6" ABOVE THE BATHTUB
SPACE, APPLIANCE OR FIXTURE. (C.B.C.-1133A.2) 2. TWO 15" WIDE MIN. BREADBOARDS MAY BE PROVIDED IN

18"
WITH A DOOR BUZZER, BELL, CHIME OR EQUIVALENT, CLEAR RIM EXTENDING UPWARD TO AT LEAST 38" ABOVE THE FLOOR. ENCLOSURES FOR BATHTUBS SHALL NOT OBSTRUCT THE MAXIMUM SLOPE OF THE SHOWER FLOOR SHALL
2) FLOOR SPACE. CLEAR WIDTH. LIEU OF THE REQUIRED 30" OF COUNTERTOP WORK SURFACE, CONTROLS OR TRANSFER FROM WHEELCHAIRS ONTO BE 12" PER FOOT IN ANY DIRECTION AND SHALL SLOPE

MIN.
THE ACTIVATING MECHANISM SHALL BE MOUNTED A

30"
A CLEAR MANEUVERING SPACE AT LEAST (30" X 48") FLOOR CL AND USED WITHOUT MEETING THE REPOSITIONING GRAB BAR BACKING SHALL BE INSTALLED HORIZONTALLY TO PERMIT
KITCHENS SHALL HAVE A MINIMUM CLEAR WIDTH MEASURED
MAX. OF 48" ABOVE THE FLOOR AND CONNECTED TO THE INSTALLATION OF A 48" GRAB BAR WITH EACH BATHTUB SEATS OR INTO BATHTUBS AND SHALL NOT TO DRAIN. THE FLOOR SURFACES SHALL BE OF
SHALL BE PROVIDED AT LAVATORIES AND SHALL BE SPACE PLAN VIEW BETWEEN ANY CABINET, COUNTERTOP OR THE FACE OF ANY REQUIREMENTS. (C.B.C.-1133A.4.1)
PERMANENT WIRING. (C.B.C.-1132A.10) END A MAXIMUM OF 6" FROM THE END WALLS OF THE BATHTUB. THE HAVE TRACKS INSTALLED ON THE RIM OF THE CARBORUNDUM OR GRIT-FACED TILE OR OF MATERIAL
CENTERED ON THE LAVATORY. (C.B.C.-1134A.8 #2) APPLIANCE (EXCLUDING HANDLES AND CONTROLS)
FORWARD APPROACH GRAB BAR REINFORCEMENT SHALL BE A MINIMUM OF 6" NOMINAL IN BATHTUB. (ANSI 2003-607.7-P.56) PROVIDING EQUIVALENT SLIP RESISTANCE.

MIN.
THAT PROJECTS INTO THE KITCHEN AND THE OPPOSING

38"
MAX.
19" LOWER SHELVING. HEIGHT. (C.B.C. 1134A5.2)

32"
(C.B.C.- 1126A.3.2.1#1) (C.B.C.-1134.8 #1 & CABINET, COUNTERTOP, APPLIANCE OR WALL AS FOLLOWS:

MIN.
CABINETS. MAX. LOWER SHELVING AND/OR DRAWER SPACE SHALL BE

24"
4. SHOWER UNIT. 3. FLOOR SPACE
(C.B.C.- 1126A.3.2.1 #2) 48" MIN. 11B-1D) 1. U-SHAPED KITCHENS, DESIGNED WITH PARALLEL PROVIDED IN THE KITCHEN AT A HEIGHT OF NO MORE THAN *** ALTHOUGH NOT A C.B.C. CODE REQUIREMENT, F.H.A. 6"
CABINETS UNDER LAVATORIES ARE ACCEPTABLE A SHOWER SPRAY UNIT IS NOT REQUIRED IN BATHTUBS. A CLEAR MANEUVERING SPACE AT LEAST 30" IN WIDTH DRAIN
PULL APPROACH AT A RANGE OR COOKTOP LOCATED AT THE 48"ABOVE THE FLOOR. (C.B.C.-1133A.5) RECOMMENDS THE PROVISION OF BACKING TO ACCEPT BY 48" IN LENGTH SHALL BE LOCATED OUTSIDE THE
PROVIDED THE BATHROOM HAS SPACE TO ALLOW A (C.B.C.-1127A.3 #2) (C.B.C. 1134A.5.4)
12" ADJOINING BASE OF THE U, SHALL HAVE A MINIMUM CLEAR WIDTH OF AT KITCHEN SINK FAUCET CONTROLS. A VERT. GRAB BAR 18" MIN. IN LENGTH ON THE CONTROL
SIDE 24" CLEAR @ BATHTUB ENCLOSURES. SHOWER, FLUSH AND PARALLEL TO THE CONTROL
PARALLEL APPROACH BY A PERSON IN A WHEELCHAIR LEAST 60" END WALL, 3" TO 6" ABOVE THE HORIZONTAL GRAB BAR

GATEWAY
MIN. PUSH WALL FAUCET CONTROLS AND OPERATING MECHANISMS SHALL BE DOORS AND PANELS OF BATHTUB ENCLOSURES SHALL BE WALL. (C.B.C.-1134A.6.#3) SIDE BACK CONTROL
MIN. EXTERIOR AND THE LAVATORY CABINETS ARE DESIGNED WITH 2. U-SHAPED KITCHENS, DESIGNED WITH A COOKTOP OR

VILLAGE-PHASE 2
PROVIDE ADDITIONAL OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT SUBSTANTIALLY CONSTRUCTED FROM APPROVED, AND 4" MAX. INWARD FROM THE FRONT EDGE OF THE WALL SIDE
DOORS SIDE SINK LOCATED AT THE BASE OF THE U, WHICH PROVIDES A
MIN.

ADAPTABLE KNEE AND TOE SPACE. (C.B.C.-1134A.8 #3) GRASPING, PINCHING OR TWISTING OF THE WRIST. THE FORCE 4. REINFORCED WALLS FOR GRAB BARS
60"

SPACE IF DOOR HAS KNEE. TO ALLOW FOR A FORWARD APPROACH, SHALL HAVE
SHATTER-RESISTANT MATERIALS. HINGED DOORS SHALL OPEN BATHTUB. (ANSI 607.4.2.2.2 -P.55)

MIN.
LOCATION OF GRAB BAR REINFORCEMENTS
MIN.

18" CLEAR @ INTERIOR REQUIRED TO ACTIVATE CONTROLS SHALL BE NO GREATER GRAB BAR REINFORCEMENT SHALL BE INSTALLED

24"
48"

BOTH LATCH & CLOSER OUTWARD. GLAZING USED IN DOORS AND PANELS OF BATHTUB
A CLEAR WIDTH OF AT LEAST 48"
MIN. DOORS 5) FINISHED FLOOR . CLEAR THAN 5 POUNDS LEVER-OPERATED, PUSH-TYPE AND ENCLOSURES SHALL BE FULLY TEMPERED, LAMINATED SAFETY GLASS CONTINUOUS IN THE WALLS OF SHOWERS 32" TO 38"
(C.B.C.-1126A.3.2.1#3) 3. ALL OTHER KITCHEN DESIGNS SHALL PROVIDE A ELECTRONICALLY CONTROLLED MECHANISMS ARE EXAMPLES
MIN.

OR APPROVED PLASTIC. (C.B.C. 1134A5.5) ABOVE THE FLOOR. THE GRAB BAR REINFORCEMENT
48"

THE FINISHED FLOOR BENEATH THE LAVATORY SHALL BE FLOOR CL MINIMUM CLEAR WIDTH OF AT LEAST 48" (C.B.C.-1133A.2.1) OF ACCEPTABLE DESIGNS. SELF-CLOSING VALVES ARE BACK WALL SHALL BE A MINIMUM OF 6" NOMINAL IN HEIGHT.
EXTENDED TO THE WALL. (C.B.C.-1134A.8 #5) SPACE REMOVABLE BASE CABINETS.

APARTMENTS
ALLOWED IF THE FAUCET REMAINS OPEN FOR AT LEAST 10
PLAN VIEW BASE CABINETS DIRECTLY UNDER KITCHEN SINKS AND SECONDS. (C.B.C.-1133A.6) GLASS-WALLED SHOWER STALLS SHALL PROVIDE 36"
30" WORK SURFACES SHALL BE REMOVABLE WITHOUT THE USE FRONT FACE OF
6) PLUMBING PROTECTION. REINFORCEMENT FOR INSTALLATION OF MIN.
MIN. PARALLEL APPROACH 15"-16"

SACRAMENTO, CALIFORNIA
WATER SUPPLY AND DRAIN PIPES UNDER LAVATORIES OF SPECIALIZED TOOLS OR SPECIALIZED KNOWLEDGE IN FLOOR-MOUNTED OR CEILING-MOUNTED GRAB BARS. VANITY OR
(C.B.C.-1126A.3.2 & (C.B.C.-1134A.8 #1)
KNEE AND TOE SPACE. 15"-16" BACK WALL BACK WALL
SHALL BE INSULATED OR OTHERWISE COVERED TO ORDER TO PROVIDE KNEE AND TOE SPACE. THE FINISH (C.B.C.-1134A.6.#4) WALL-HUNG
1132A.5.2) FRONT APPROACH BACK WALL

END WALL
CLEAR

MIN. END WALL

FLOOR BENEATH KITCHEN SINKS AND WORK SURFACES

CONTROL
LAVATORY IN LINE

15" CONTROL
1. THE KNEE AND TOE SPACE SHALL BE CLEAR AND

HEAD END
PROTECT AGAINST CONTACT. THERE SHALL BE NO SHARP

HEAD END
(C.B.C.-1126A.3.2.1) SHALL BE EXTENDED TO THE WALL. (C.B.C.-1133A.3)

END WALL
FLOOR

SEAT
CONTROL
UNOBSTRUCTED,OR REMOVABLE BASE CABINETS PROVIDED. 5. THRESHOLDS WITH CONTROL

HEAD END
OR ABRASIVE SURFACES UNDER LAVATORIES.

MIN.
36"
COUNTERTOPS.

SEAT
2. THE KNEE AND TOE SPACE SHALL BE 30" WIDE MIN, WHEN A THRESHOLD IS USED, IT SHALL BE A MAXIMUM WALL SPACE

WALL
WALL
(C.B.C.-1134A.8 #6) 1. A MINIMUM LINEAR LENGTH OF 30" OF COUNTERTOP CENTERED ON THE SINK, COUNTERTOP OR APPLIANCE. OF 2" IN HEIGHT AND HAVE A BEVELED OR SLOPED F.H.A.-P.7.

WALL
SHALL BE PROVIDED FOR THE KITCHEN SINK INSTALLATION. 3. A CLEAR FLOOR SPACE SHALL NOT EXTEND INTO THE ANGLE NOT EXCEEDING 1 UNIT VERTICAL IN 2 UNITS
54" 8) MIRRORS AND TOWEL FIXTURES. 2. A MINIMUM LINEAR LENGTH OF 30" OF COUNTERTOP KNEE AND TOE SPACE MORE THAN 19" (C.B.C.-1133A.7) HORIZONTAL. THRESHOLDS 1/2"OR LESS IN HEIGHT
MIN. WHERE MIRRORS OR TOWEL FIXTURES ARE PROVIDED TOWEL SHALL BE PROVIDED FOR A WORK SURFACE. MAY HAVE A BEVELED OR SLOPED ANGLE NOT
FIXTURE 3. SINKS AND WORK SURFACES MAY BE A SINGLE CLEAR 30"X CLEAR

MIN.
THEY SHALL BE MOUNTED WITH THE BOTTOM EDGE OF THE PLUMBING PROTECTION. EXCEEDING 1 UNIT VERTICAL IN 1 UNIT HORIZONTAL.

30"
PULL CL INTEGRAL UNIT A MINIMUM OF 60 INCHES (1524 MM) IN CLEAR CL FLOOR 48" MIN. FLOOR

MIN.
REFLECTIVE SURFACE NO HIGHER THAN 40" FROM THE WATER SUPPLY AND DRAIN PIPES UNDER KITCHEN SINKS (C.B.C.-1134A.6.#5)

30"

F.H.A.(P.7.53-55)
(C.B.C.-1134A.5 )
SIDE LENGTH, OR BE SEPARATE COMPONENTS. FLOOR SPACE SPACE

MIN.
PUSH SHALL BE INSULATED OR OTHERWISE COVERED TO PROTECT

48"
FLOOR. (C.B.C.-1134A.8 #8)
44" MIN.
MIN.

36" BOTTOM EDGE OF

60"

(C.B.C.-1134A.5 )
SIDE AGAINST CONTACT. THERE SHALL BE NO SHARP OR ABRASIVE SPACE 7. SHOWER ENCLOSURES
MAX.

REFLECTIVE SURFACE EXCEPTION: TWO 15"WIDE MINIMUM BREADBOARDS MAY BE FIGURE "B"
40"

SURFACES UNDER KITCHEN SINKS. (C.B.C.-1133A.7.1) 19" DOORS AND PANELS OF SHOWER ENCLOSURES SHALL
Y

PROVIDED IN LIEU OF THE REQUIRED 30" OF COUNTERTOP

19" MAX. LENGTH OF BATHTUB BE SUBSTANTIALLY CONSTRUCTED FROM APPROVED,
MIRROR & TOWEL FIXTURE: SURFACE. SHATTER-RESISTANT MATERIALS. HINGED SHOWER
MIN. MAX. 21"
(C.B.C.-1134A.8#8) (C.B.C.-1133A.4) BATHTUB DOORS SHALL OPEN OUTWARD. GLAZING USED IN
F.F. 21"
LENGTH OF BATHTUB CLEARANCE DOORS AND PANELS OF SHOWER ENCLOSURES SHALL
LENGTH OF BATHTUB THE EDGE OF THE BE FULLY TEMPERED, LAMINATED SAFETY GLASS OR 36"
SIDE APPROACH CLEAR FLOOR SPACE APPROVED PLASTIC.
(C.B.C.- 1126A.3.2.2 #1) MIN.

12"
HINGE - SIDE APPROACH NOTE: Y= 48" MIN. IF FRONT APPROACH REMOVABLE SEAT (30"X48") MIN.; SHALL (C.B.C.-1134A.6.#7) ADDITIONAL 12"

D E B A R T O L O
(C.B.C.-1126A.3.2.2) DOOR HAS BOTH REMOVABLE SEAT BE FLUSH WITH THE CLEAR FLOOR
RECOMMENDED 18" MAX. SPACE.
LATCH & CLOSER 15" 15" CONTROL WALL
FOR DEPTH OF PANTRY F.H.A.-P.7.
(C.B.C.-1126A.3.2.2 #2) MIN. MIN. SURFACE
(F.H.A.-P.7.17) BACK WALL BACK WALL CLEAR

MIN.
42"
BATHING & TOILET FACILITIES WITHIN COVERED

MIN.
(P.54, 62 & 93)

(P.54, 62 & 93)

(C.B.C.-1134A.5 #1)

ANSI
ANSI

48"
REINFORCING FOR WALL HUNG BENCH SEAT IS EDGE OF WALL FLOOR

END WALL

END WALL
MULTIFAMILY DWELLING UNITS:(C.B.C.- 1134A)

CONTROL

CONTROL
HEAD END

HEAD END
LOCATED ON THE WALL OPPOSITE THE HUNG LAVATORY SPACE

SEAT

SEAT
CABINETS UNDER CONTROLS & MUST RUN THE FULL WIDTH OF
BATHROOMS SHALL BE DESIGNED TO COMPLY WITH ONE OF THE FOLLOWING OPTIONS:
LAVATORIES & TOILETS

MAX.
PULL PUSH
60' MIN.

WALL

WALL
THE STALL, STARTING @ THE FLOOR TO 24" MIN.

6"
44" MIN.

SIDE SIDE SHALL NOT ENCROACH HEIGHT.

ALL BATHROOMS WITHIN THE DWELLING UNIT SHALL ONLY ONE BATHROOM WITHIN THE INTO THE CLEAR
OPTION I : OPTION II : (F.H.A.-P.6.13)
Y

24" MIN. 24" COMPLY WITH THE FOLLOWING: DWELLING UNIT SHALL COMPLY WITH SPACE
MIN. THE FOLLOWING: CLEAR CLEAR

(C.B.C.-1134A.5 )
(C.B.C.-1134A.5 )
(C.B.C.- 1126A.3.2.1 #1) 1. TOILET, BATHING & SHOWER FACILITIES SHALL COMPLY WITH (C.B.C.-1134A.5 #1)

MIN.
30"
FLOOR FLOOR FIGURE "C"

ARDEN
(C.B.C.- 1134A.4) #: 1, 2, 3, 4 & 5, THE SAME AS ABOVE ITEMS (FOR GLASS SHOWER STALLS ARE NOT REQUIRED TO

MIN.
SPACE SPACE

48"
OPTION I ) HAVE THE WATERPROOF PAN OR FLOOR SEAL
LATCH - SIDE APPROACH 2. BATHTUBS SHALL COMPLY WITH (C.B.C.1134A.5) PIERCED TO RECEIVE SCREWS/BOLTS FOR
(C.B.C.- 1126A.3.2.3) NOTE: Y= 48" MIN. IF 2'-6" FLOOR MOUNTED GRAB BARS.
6. WHERE BOTH A TUB & SHOWER ARE PROVIDED LENGTH OF BATHTUB 12" LENGTH OF BATHTUB 12"
DOOR HAS CLOSER MIN.
3. SHOWERS SHALL COMPLY WITH (C.B.C.-1134A.6) IN THE BATHROOM, AT LEAST ONE SHALL BE MIN.* MIN.* (F.H.A.-P.6.12) PREFERRED LOCATION
(C.B.C.-1126A.3.2.3 #2) MADE ACCESSIBLE. 48" FOR CONTROLS
INDICATES DIRECTION
42" MIN.

FRONT APPROACH SIDE APPROACH F.H.A.-P.7. 7

4. WATER CLOSETS SHALL COMPLY WITH (C.B.C.- 1134A.7) * ANSI * ANSI OF APPROACH IN GLASS SHOWER STALLS, ONLY THOSE WALLS

28" TO 34"
ADDITIONAL REQUIREMENTS APPLY TO DWELLING PERMANENT SEAT PERMANENT SEAT
(607.2-P.54) (607.2-P.54)
UNITS CONTAINING TWO OR MORE BATHROOMS THAT ARE SOLID CONSTRUCTION MUST HAVE
5. LAVATORIES, VANITIES, MIRRORS & TOWEL FIXTURES REINFORCED AREAS.
WHEN A BATHTUB IS PROVIDED AS THE
SHALL COMPLY WITH (C.B.C.- 1134A.8) 60" MIN. (F.H.A.-P.6.12)

12"
ACCESSIBLE BATHING FIXTURE.
6. BATHROOMS SHALL BE PROVIDED WITH AN ACCESSIBLE

48"
SIDE APPROACH DOORWAYS ROUTE INTO & THROUGH THE BATHROOM. 60" CLEAR MIN. BETWEEN
WHERE TWO OR MORE BATHROOMS ARE
W/OUT DOORS/ GATES FACES OF REINFORCING FOR GRAB BARS @ BATHTUB: WHERE MULTIPLE GRAB BARS ARE USED, CLEAR
7. IF A DOOR PROVIDED, IT SHALL COMPLY WITH THE PROVIDED WITHIN THE SAME DWELLING UNIT AND REPOSITIONABLE EDGE OF
(C.B.C.-1126A.3.4.2) CABINETS,COUNTERTOPS, (C.B.C.-1134A.5.2) REQUIRED HORIZONTAL GRAB BARS SHALL BE FLOOR
REQUIREMENTS OF (C.B.C.-1132A.5) A BATHTUB IS INSTALLED TO COMPLY WITH OPTION COUNTERTOP AND VANITY
FIXTURES OR INSTALLED AT THE SAME HEIGHT ABOVE THE SPACE
II, ITEM 6 IN ONE BATHROOM AND A SHOWER STALL SINK WITH
8. A MIN. 18" CLEAR MANEUVERING SPACE SHALL BE PROVIDED APPLIANCES. FLOOR.
REMOVABLE BASE VERTICAL VERTICAL
ON THE SWING SIDE OF THE DOOR AT THE STRIKE EDGE OF THE U-SHAPED KITCHENS, DESIGNED WITH PARALLEL NOTE:
IS PROVIDED IN A SUBSEQUENT BATHROOM, BOTH GRAB BAR GRAB BAR 6" 52" 6" (ANSI P.57) 32" NOMINAL CLEAR
APPROACH @ A RANGE OR COOKTOP LOCATED AT ALL DIMENSIONS CABINET
DOOR 6" MAX. 52" 6" MAX.
48" MIN.

THE BATHTUB SELECTED TO COMPLY WITH OPTION (ANSI P.55) (ANSI P.55) MAX. MIN. MAX. WIDTH FOR STALL
42" MIN.

42" MIN.

THE BASE OF THE "U", SHALL HAVE A MIN. CLEAR SHOWN ARE MIN. FINISH FLOOR MIN.
24" MIN. 9. SWITCHES, OUTLETS AND CONTROLS SHALL COMPLY WITH II ITEM 6 AND AT LEAST ONE SHOWER STALL CLEAR DIMENSIONS MATERIAL SHALL BE DOOR
WIDTH OF AT LEAST 60".

33"-36" 3"-6" 18"

33"-36" 3"-6" 18"

22" WITHIN THE DWELLING UNIT SHALL MEET ALL THE ***(FIGURES "B", "C" & "D" APPLY TO SECONDARY FIGURE "D"
(C.B.C. 1142A) FINISH TO FINISH. CONTINUOUS AND
(C.B.C.-1133A.2.1 #1) SHOWERS, WHICH DO NOT REQUIRE THE MIN.
APPLICABLE ACCESSIBILITY REQUIREMENTS COOKTOP OR SINK. THE WALL BEHIND & REQUIREMENTS FOR CLEAR FLOOR SPACE
10. REINFORCED WALLS TO ALLOW FOR THE FUTURE DIMENSIONS SHOWN ON THE PRIMARY BATHING
PROVIDED IN SECTION 1134.(SEE SECTION 1134.5 W/ 30" KNEESPACE SURROUNDING BASE
INSTALLATION OF GRAB BARS SHALL COMPLY WITH FACILITY.)
FOR BATHTUBS OR SECTION 1134.6 FOR SHOWERS) TO A HEIGHT OF 27" CABINET ARE TO BE
(C.B.C.-1134A.5) FOR BATHTUBS, (1134A.6) FOR SHOWERS &

MAX.

MAX.
MIN.

MIN.
(1134A.7) FOR WATER CLOSETS. GRAB BARS SHALL COMPLY WITH FINISHED

38"

38"
FRONT APPROACH POCKET OR HINGE STOP OR LATCH

6"

6"
7. WHEN TWO OR MORE LAVATORIES ARE
(C.B.C.-1126A.3.4.1) SIDE APPROACH SIDE APPROACH (C.B.C.-1127A.4) , & (C.B.C.-1127A.2.2,item 4) .
PROVIDED, AT LEAST ONE SHALL BE MADE
(C.B.C.-1126A.3.4.3) (C.B.C.-1126A.3.4.4) SEAT
ACCESSIBLE & COMPLY WITH SECTION 1134A.8. NOTE:
SLIDING DOORS INDICATES DIRECTION FOR NON-ACCESSIBLE SHOWER REQUIREMENTS REFER TO U.C.P.C. 2001, SECTION 411.7
BACK BACK
(C.B.C.-1126A.3.4) OF APPROACH SUFFICIENT MANEUVERING SPACE. POWDER ROOMS:(C.B.C.-1134A.3)
(C.B.C.-1134A.4) WITH SEAT IN TUB WITH PERMANENT SEAT
ALL POWDER ROOMS SHALL BE DESIGNED TO (C.B.C.- 1134A.5#2)
PULL
BATHING & TOILET FACILITIES REQUIRED TO BE ADAPTABLE COMPLY WITH SECTION 1134A.2 , OPTION II ITEMS 8
SIDE 24" CLEAR @ EXT. RECOMMENDED 28" TEMPORARY GARBAGE STORAGE CLEAR DOOR ACCESS:
SHALL PROVIDE SUFFICIENT MANEUVERING SPACE FOR A THROUGH. 12 MILESTONE:
MIN. DOORS PUSH PUSH PERSON USING A WHEELCHAIR OR OTHER MOBILITY AID TO WORK BACKING FOR MIN. (C.B.C.-1126A.1)
** ANSI THIRD CITY SUBMITTAL
SIDE SIDE WHEN THE POWDER ROOM IS THE ONLY TOILET 6"
MIN.

ENTER & CLOSE THE DOOR, USE THE FIXTURES, REOPEN THE SURFACE VERT. GRAB BAR,
48" MIN.

48" MIN.
60"

(P.56) 33"
18" CLEAR @ INT. 12" DOOR & EXIT. FACILITY LOCATED ON AN ACCESSIBLE LEVEL, IT (ANSI P.55) MIN.** 2'-10"CLR. 3'-0"CLR.
2'-6"

COM-2213627 to COM-2213634
MIN. DOORS SHALL COMPLY WITH THE OPTION II ITEMS PLUS ALL 28" 1126A.1 WIDTH AND HEIGHT OF 5 5 2'-95 8" 13 "
MIN. 8" 2'-8" 13 8" 8" 4
WHERE THE DOOR SWINGS INTO THE BATHROOM OR POWDER ADDITIONAL REQUIREMENTS LOCATED IN SECTIONS MIN. DOORS AND GATES. DOORWAYS
DRAWN: MH, NM
X>8"

X>8"

MIN. 1134.7 & 1134.8. WHICH PROVIDE ACCESS TO

X>8"

ROOM, THERE SHALL BE A CLEAR MANEUVERING SPACE OUTSIDE

MAX.
7"
COMMON USE AREAS OR COVERED
28" TO 34"

MIN.**
DISPOSAL
THE SWING OF THE DOOR OF AT LEAST 30"X48" WITHIN THE CHECKED:
MULTIFAMILY DWELLINGS SHALL JM

59"
ROOM. THE CLEAR MANEUVERING SPACE SHALL ALLOW THE 48" MIN. (2) 12"W X 18"H X
COMPLY WITH THE FOLLOWING:

34"
24"D= 3 CUBIC
USER TO POSITION A WHEELCHAIR OR OTHER MOBILITY AID KIT. PLOT DATE: Monday, October 24, 2022

MIN.

MIN.
38"

38"
MAX.

MAX.
PULLSIDE APPROACH PUSHSIDE APPROACH PUSHSIDE APPROACH 48" CLEAR MIN. BETWEEN SINK

32"

32"
CLEAR OF THE PATH OF THE DOOR AS IT IS CLOSED AND TO 31.5"W X 8.75"H
1. PERMIT THE INSTALLATION OF A 34" INTERIOR DOOR 36" EXTERIOR DOOR
(C.B.C.-1126A.3.2.1#1) (C.B.C.-1126A.3.2.1#2) DOOR WITH BOTH, PERMIT USE OF FIXTURES. FACES OF CABINETS, DOOR OR GATE NOT LESS THAN 36" (34"W X 1 3/8"T X 80" HT.) (36"W X 1 3/4"T X 84" HT.)
X 20"D= 3 CUBIC
LATCH & CLOSER COUNTERTOPS, FIXTURES IN WIDTH, NOT LESS THAN 80" IN E D A RC
(C.B.C.-1126A.3.2.1#3) DOORS MAY SWING INTO THE REQUIRED CLEAR SPACE AT ANY OR APPLIANCES. REMOVABLE BASE LOCATION OF TEMP. GARBAGE,
RECYCLING & ORGANICS
HEIGHT, AND PROVIDE A CLEAR ER
OPENING OF NOT LESS THAN 32",
R Z JA

H
ST
FIXTURE WHEN A CLEAR MANEUVERING SPACE IS PROVIDED CABINET
MA
STORAGE IN ALL UNITS
HEAD FOOT MEASURED WITH THE DOOR B

IT E
U-SHAPED KITCHENS, DESIGNED WITH A COOKTOP
OUTSIDE THE SWING ARC OF THE DOOR SO IT CAN BE CLOSED.

R EG I
FA RA
OR SINK LOCATED AT THE BASE OF THE "U" WHICH NOTE: UNITS WITH 36" COUNTERTOP POSITIONED AT AN ANGLE OF 90 WIDTH, HEIGHT & CLEAR OPENING FOR INTERIOR & EXTERIOR

BA
KITCHEN HEIGHT, ARE SIM. DOORS OF COVERED MULTIFAMILY DWELLINGS (C.B.C. 1126A.1)
FINISH FLOOR DEGREES FROM ITS CLOSED

CT
PROVIDES A 30" KNEE SPACE TO A HEIGHT OF 27"
MATERIAL SHALL BE POSITION. (C.B.C.-1126A.1)

RI
ABOVE THE FLOOR TO ALLOW FOR A FORWARD No. C 15528

THIRD CITY SUBMITTAL 10/26/2022

APPROACH, SHALL HAVE A CLEAR WIDTH OF AT CONTINUOUS AND THE
DEFINITIONS: WALL BEHIND &
(C.B.C.-CHAPTER 2, DEFINITIONS) LEAST 48".
SURROUNDING BASE
ELECTRICAL RECEPTACLE, SWITCH AND CONTROL HEIGHTS: Exp. 03/31/23
________
(C.B.C.-1133A.2. #2) (C.B.C.1136A.1 & 2 ALSO 1142A)
CABINET ARE TO BE TA

IA
N

S
TE
O F CA L I F O R
COVERED MULTIFAMILY DWELLINGS : ACCESSIBLE ROUTE : FINISHED
“COVERED MULTIFAMILY DWELLINGS” MEANS EITHER OF THE WHERE THE DOOR SWINGS INTO THE BATHROOM (OR
A CONTINUOUS UNOBSTRUCTED PATH CONNECTING
FOLLOWING: POWDER ROOM ), THERE SHALL BE A CLEAR X
ACCESSIBLE ELEMENTS AND SPACES OF AN ACCESSIBLE SITE,
1. BUILDINGS THAT CONSIST OF AT LEAST FOUR BUILDING OR FACILITY THAT CAN BE MANEUVERING SPACE OUTSIDE THE SWING OF THE
CONDOMINIUM DWELLING UNITS OR AT LEAST THREE DOOR OF AT LEAST 30"X48" WITHIN THE ROOM TOP & BOTTOM OF

MAX.
NEGOTIATED BY A PERSON WITH A DISABILITY USING A

48"
APARTMENT DWELLING UNITS IF THE BUILDINGS HAVE (C.B.C.-1134A.4) KITCHEN RECEPTACLE OUTLETS,
Y

WHEELCHAIR, AND THAT IS ALSO SAFE FOR AND USABLE BY

MAX.

AT LEAST ONE ELEVATOR. SWITCHES & CONTROL PROJECT NO. 2021-051

34"

PERSONS WITH OTHER DISABILITIES. BASE

VITREOUS CHINA
PENNINGTON
K-T13140-3B
LAVATORY
PINSTRIPE
FAUCETS
K-2196-8
BRASS

2. THE GROUND FLOOR DWELLING UNITS IN BUILDINGS INTERIOR ACCESSIBLE ROUTES MAY INCLUDE CORRIDORS, BOXES HEIGHT.
CABINET

MIN.
15"
THAT CONSIST OF AT LEAST FOUR CONDOMINIUM DWELLING HALLWAYS, FLOORS, RAMPS, ELEVATORS AND LIFTS. EXTERIOR THERE SHALL BE A MIN. CLEAR FLOOR SPACE 48" (C.B.C.-1136A.2) PROJECT PHASE .
UNITS OR AT LEAST THREE APARTMENT DWELLING UNITS IF THE ACCESSIBLE ROUTES MAY INCLUDE PARKING ACCESS AISLES, PARALLEL BY 30" PERPENDICULAR TO THE SIDE OF F.F.
BUILDING DOES NOT HAVE AN ELEVATOR. CURB RAMPS, CROSSWALKS AT VEHICULAR WAYS, WALKS, THE BATHTUB OR BATHTUB -SHOWER COMBINATION (2) 15" MIN. WIDTH SHEET TITLE
COVERED MULTIFAMILY DWELLINGS INCLUDE DWELLINGS RAMPS AND LIFTS. MOUNTING HEIGHT FOR OUTLETS,
(MEASURED FROM THE FOOT OR DRAIN END OF THE BREADBOARDS MAX. REACH OVER AN
LISTED IN SECTION 1102A.1. FOR PURPOSES OF THIS
(C.B.C.-SECTION 202, DEFINITIONS) BATHTUB) TO PROVIDE FOR THE MANEUVERING OF A (C.B.C.-1133A.4 #3) OBSTRUCTION SWITCHES & CONTROL BOXES
DEFINITION,
DWELLING UNITS WITHIN A SINGLE STRUCTURE SEPARATED BY
FIREWALLS DO NOT CONSTITUTE SEPARATE BUILDINGS. COMMON USE AREAS :
WHEELCHAIR AND TRANSFER TO AND FROM THE
BATHING FACILITIES... CABINET UNDER LAVATORIES
RESIDENTIAL
(C.B.C.-SECTION 202, DEFINITIONS) PRIVATE USE AREAS WITHIN MULTIFAMILY RESIDENTIAL
FACILITIES WHERE THE USE OF THESE AREAS IS LIMITED
EXCLUSIVELY TO OWNERS, RESIDENTS AND THEIR GUESTS THE
AND TOILETS SHALL NOT ENCROACH INTO THE CLEAR
FLOOR SPACE.
B18 B18
REACH LIMITS OVER AN OBSTRUCTION
ELECTRICAL
OUTLET CODE
ACCESSIBLE : (C.B.C.-1134A.5) MOUNTED 46"
A SITE, BUILDING, FACILITY, OR PORTION THEREOF THAT IS
AREAS MAY BE DEFINED AS ROOMS OR SPACES OR ELEMENTS "X" "Y" A.F.F. MAX. REFERENCES
MIN.

INSIDE OR OUTSIDE OF A BUILDING.

36"

APPROACHABLE AND USABLE BY PERSONS WITH DISABILITIES IN

COMPLIANCE WITH THIS CODE. (C.B.C.-SECTION 202, DEFINITIONS) 48" MIN. BASE CABINET LESS THAN 20" 48" MAX. STANDARD 24" This set of plans and specifications must be
(C.B.C.-SECTION 202, DEFINITIONS)
ACCESSIBILITY :
ADAPTABLE DWELLING UNIT :
AN ACCESSIBLE DWELLING UNIT WITHIN A COVERED
48" CLEAR BETWEEN
(18" MIN. WIDTH),
FOR BREAD BOARD 44" MAX.FORWARD
DEEP COUNTER
& BASE
kept on the job at all times and it is unlawful to ISSUED BY SHEET NO.
FACES OF CABINETS, BETWEEN 20" & 25" make any changes or alterations from the Community Development Department
THE COMBINATION OF VARIOUS ELEMENTS IN A BUILDING, MULTIFAMILY BUILDING AS DESIGNED WITH ELEMENTS AND LOWER SHELVING: INSTALLATION APPROACH. CABINETS
COUNTERTOPS, same without written permission from the
FACILITY, SITE, OR AREA, OR PORTION THEREOF WHICH SPACES ALLOWING THE DWELLING UNIT TO BE ADAPTED OR ELECTRICAL OUTLETS
Ann Rosendale
46" MAX.
FIXTURES OR 24" MAX. PLAN Building Inspection Division. By:

A9-1.5
ALLOWS ACCESS, CIRCULATION AND THE FULL USE OF THE ADJUSTED TO ACCOMMODATE THE USER. ON WALLS OVER
APPLIANCES. LOWER SHELVING AND/ OR DRAWER SPACE SHALL SIDE APPROACH. The approval of this plan and specification
BUILDING AND FACILITIES BY PERSONS WITH DISABILITIES IN (C.B.C.-SECTION 202, DEFINITIONS) BE PROVIDED IN THE KITCHEN AT THE HEIGHT OF NO CABINETS MUST BE A
COMPLIANCE WITH THIS CODE. ALL OTHER KITCHEN DESIGNS SHALL PROVIDE A MIN.
NOTE: OBSTRUCTIONS SHALL NOT EXTEND SHALL NOT be held to permit or approve the on Jan 20, 2023
CLEAR WIDTH OF AL LEAST 48". MORE THAN 48" ABOVE THE FLOOR. MIN. 36" FROM A
(C.B.C.-SECTION 202, DEFINITIONS) violation of any City Ordinance or State Law.
(C.B.C.-1133A.5) MORE THAN 25" FROM THE WALL BENEATH CORNER. F.H.A.
(C.B.C.- 1133A.2.1 #3)
THE RECEPTACLE. (P. 5.6-5.8)