Name : Sewbesew Yimer

Exercise 2: Subnetting Scenario 2 (Classful Addressing)

Topology Diagram
Addressing Table

Device Interface IP Address Subnet Mask Default Gateway

ISP S0/0/0 209.165.200.227 255.255.255.224 N/A

Fa0/0 172.16.16.1 255.255.254.0 N/A
S0/0/0 172.16.14.1 255.255.254.0 N/A
HQ
S0/0/1 172.16.18.1 255.255.254.0 N/A
S0/1/0 209.165.200.226 255.255.255.224 N/A
Fa0/0 172.16.12.1 255.255.254.0 N/A
S0/0/0 172.16.15.254 255.255.254.0 N/A
West
S0/0/1 172.16.8.1 255.255.254.0 N/A
S0/1/0 172.16.10.1 255.255.254.0 N/A
Fa0/0 172.16.20.1 255.255.254.0 N/A
S0/0/0 172.16.19.254 255.255.254.0 N/A
East
S0/0/1 172.16.22.1 255.255.254.0 N/A
S0/1/0 172.16.24.1 255.255.254.0 N/A
Fa0/0 172.16.2.1 255.255.254.0 N/A
Branch 1 S0/0/0 172.16.9.254 255.255.254.0 N/A
S0/0/1 172.16.6.1 255.255.254.0 N/A
Fa0/0 172.16.4.1 255.255.254.0 N/A
Branch 2 S0/0/0 172.16.11.254 255.255.254.0 N/A
S0/0/1 172.16.7.254 255.255.254.0 N/A
Fa0/0 172.16.28.1 255.255.254.0 N/A
Branch 3 S0/0/0 172.16.23.254 255.255.254.0 N/A
S0/0/1 172.16.26.1 255.255.254.0 N/A
Fa0/0 172.16.30.1 255.255.254.0 N/A
Branch 4 S0/0/0 172.16.25.254 255.255.254.0 N/A
S0/0/1 172.16.27.254 255.255.254.0 N/A
PC1 NIC 172.16.17.254 255.255.254.0 172.16.16.1
PC2 NIC 172.16.13.254 255.255.254.0 172.16.12.1
PC3 NIC 172.16.21.254 255.255.254.0 172.16.20.1
PC4 NIC 172.16.3.254 255.255.254.0 172.16.2.1
PC5 NIC 172.16.5.254 255.255.254.0 172.16.4.1
PC6 NIC 172.16.29.254 255.255.254.0 172.16.28.1
PC7 NIC 172.16.31.254 255.255.254.0 172.16.30.1

Learning Objectives
Upon completion of this lab, you will be able to:

2
  Determine the number of subnets needed.
 Determine the number of hosts needed.
 Design an appropriate addressing scheme.
 Assign addresses and subnet mask pairs to device interfaces and hosts.
 Examine the use of the available network address space.
 Determine how static routing could be applied to the network.

Scenario
In this lab, you have been given the network address 172.16.0.0/16 to subnet and provide the IP
addressing for the network shown in the Topology Diagram. The network has the following addressing
requirements:
 The Branch 1 LAN will require 100 host IP addresses.
 The Branch 2 LAN will require 100 host IP addresses.
 The Branch 3 LAN will require 100 host IP addresses.
 The Branch 4 LAN will require 100 host IP addresses.
 The West LAN will require 400 hosts.
 The East LAN will require 400 hosts.
 The HQ LAN will require 500 host IP addresses.
 The links between each of the routers will require an IP address for each end of the link.
The IP addresses for the link from the HQ router to the ISP have already been assigned. The Serial 0/2
address of the HQ router is 209.165.200.226/27. The IP address of the Serial 0/0 of the ISP router is
209.165.200.227/27.

Task 1: Examine the Network Requirements.

Examine the network requirements and answer the questions below. Keep in mind that IP addresses will
be needed for each of the LAN interfaces.
How many subnets are needed? 15
What is the maximum number of IP addresses that are needed for a single subnet? 500
How many IP addresses are needed for each of the branch LANs? 100
How many IP addresses are needed for all of the connections between routers? 16
What is the total number of IP addresses that are needed? 1716

Task 2: Design an IP Addressing Scheme.

Step 1: Subnet the 172.16.0.0 network into the appropriate number of subnets.
What will the subnet mask be for the subnetworks? 255.255.254.0 or /23
How many usable host IP addresses are there per subnet? 510
Fill in the following chart with the subnet information.

Subnet Subnet IP First Usable Host IP Last Usable Host IP Broadcast

Number Address
0 172.16.0.0 172.16.0.1 172.16.1.254 172.16.1.255
1 172.16.2.0 172.16.2.1 172.16.3.254 172.16.3.255
2 172.16.4.0 172.16.4.1 172.16.5.254 172.16.5.255
3 172.16.6.0 172.16.6.1 172.16.7.254 172.16.7.255
4 172.16.8.0 172.16.8.1 172.16.9.254 172.16.9.255
3
 5 172.16.10.0 172.16.10.1 172.16.11.254 172.16.11.255
6 172.16.12.0 172.16.12.1 172.16.13.254 172.16.13.255
7 172.16.14.0 172.16.14.1 172.16.15.254 172.16.15.255
8 172.16.16.0 172.16.16.1 172.16.17.254 172.16.17.255
9 172.16.18.0 172.16.18.1 172.16.19.254 172.16.19.255
10 172.16.20.0 172.16.20.1 172.16.21.254 172.16.21.255
11 172.16.22.0 172.16.22.1 172.16.23.254 172.16.23.255
12 172.16.24.0 172.16.24.1 172.16.25.254 172.16.25.255
13 172.16.26.0 172.16.26.1 172.16.27.254 172.16.27.255
14 172.16.28.0 172.16.28.1 172.16.29.254 172.16.29.255
15 172.16.30.0 172.16.30.1 172.16.31.254 172.16.31.255

Step 2: Assign the subnets to the network shown in the Topology Diagram.
When assigning the subnets, keep in mind that routing will need to occur to allow information to be sent
throughout the network. The subnets will be assigned to the networks to allow for route summarization on
each of the routers.
1. Assign subnet 1 to the Branch 1 LAN subnet: 172.16.2.0 /23
2. Assign subnet 2 to the Branch 2 LAN subnet: 172.16.4.0 /23
3. Assign subnet 3 to the link between the Branch 1 and Branch 2 routers: 172.16.6.0 /23
4. Assign subnet 4 to the link between the Branch 1 and West routers: 172.16.8.0 /23
5. Assign subnet 5 to the link between the Branch 2 and West routers: 172.16.10.0 /23
6. Assign subnet 6 to the West LAN subnet: 172.16.12.0 /23
7. Assign subnet 7 to the link between the West and HQ routers: 172.16.14.0 /23
8. Assign subnet 8 to the HQ LAN subnet: 172.16.16.0 /23
9. Assign subnet 9 to the link between the HQ and East routers: 172.16.18.0 /23
10. Assign subnet 10 to the East LAN subnet: 172.16.20.0 /23
11. Assign subnet 11 to the link between the Branch 3 and East routers: 172.16.22.0 /23
12. Assign subnet 12 to the link between the Branch 4 and East routers: 172.16.24.0 /23
13. Assign subnet 13 to the link between the Branch 3 and Branch 4 routers: 172.16.26.0 /23
14. Assign subnet 14 to the Branch 3 subnet: 172.16.28.0 /23
15. Assign subnet 15 to the Branch 4 subnet: 172.16.30.0 /23

Task 3: Assign IP Addresses to the Network Devices.

Assign the appropriate addresses to the device interfaces. Document the addresses to be used in the
Addressing Table provided under the Topology Diagram.

Step 1: Assign addresses to the HQ router.

1. Assign the first valid host address in the HQ LAN subnet to the LAN interface.
2. Assign the first valid host address in the link from HQ to West subnet to the S0/0/0 interface.
3. Assign the first valid host address in the link from HQ to East subnet to the S0/0/1 interface.

Step 2: Assign addresses to the West router.

1. Assign the first valid host address in the West LAN subnet to the LAN interface.
2. Assign the last valid host address in the link from HQ to West subnet to the S0/0/0 interface.

4
 3. Assign the first valid host address in the link from West to Branch 1 subnet to the S0/0/1
interface.
4. Assign the first valid host address in the link from West to Branch 2 subnet to the S0/1/0
interface.

Step 3 Assign addresses to the East router.

1. Assign the first valid host address in the East LAN subnet to the LAN interface.
2. Assign the last valid host address in the link from HQ to East subnet to the S0/0/0 interface.
3. Assign the first valid host address in the link from East to Branch 3 subnet to the S0/0/1 interface.
4. Assign the first valid host address in the link from East to Branch 4 subnet to the S0/1/0 interface.

Step 4 Assign addresses to the Branch 1 router.

1. Assign the first valid host address in the Branch 1 LAN subnet to the LAN interface.
2. Assign the last valid host address in the link from West to Branch 1 subnet to the S0/0/0 interface.
3. Assign the first valid host address in the link from Branch 1 to Branch 2 subnet to the S0/0/1
interface.

Step 5 Assign addresses to the Branch 2 router.

1. Assign the first valid host address in the Branch 2 LAN subnet to the LAN interface.
2. Assign the last valid host address in the link from West to Branch 2 subnet to the S0/0/0 interface.
3. Assign the last valid host address in the link from Branch 1 to Branch 2 subnet to the S0/0/1
interface.

Step 6 Assign addresses to the Branch 3 router.

1. Assign the first valid host address in the Branch 3 LAN subnet to the LAN interface.
2. Assign the last valid host address in the link from East to Branch 3 subnet to the S0/0/0 interface.
3. Assign the first valid host address in the link from Branch 3 to Branch 4 subnet to the S0/0/1
interface.

Step 7 Assign addresses to the Branch 4 router.

1. Assign the first valid host address in the Branch 4 LAN subnet to the LAN interface.
2. Assign the last valid host address in the link from East to Branch 4 subnet to the S0/0/0 interface.
3. Assign the last valid host address in the link from Branch 3 to Branch 4 subnet to the S0/0/1
interface.

Step 8 Assign addresses to the host PCs

1. Assign the last valid host address in the HQ LAN subnet to PC1.
2. Assign the last valid host address in the West LAN subnet to PC2.
3. Assign the last valid host address in the East 1 LAN subnet to PC3.
4. Assign the last valid host address in the Branch 1 LAN subnet to PC4.
5. Assign the last valid host address in the Branch 2 LAN subnet to PC5.
6. Assign the last valid host address in the Branch 3 LAN subnet to PC6.
7. Assign the last valid host address in the Branch 4 LAN subnet to PC7.