Scribd
Upload
16 views3 pages

12 Assignment 11

Uploaded by

Vishal kaundal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
16 views3 pages

12 Assignment 11

Uploaded by

Vishal kaundal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

LAB: Assignment 11

Objective: Configure a Routing Internet Protocol (RIP) Using GNS.

Instructions: The instructor is required to discuss the following questions with the students.
Students are required to make solution and check connectivity using PING command.

Procedure:
1. Create a topology as shown in the figure.
2. Configure all the routers.
3. Implement RIP protocols in the router to configure the network.

Configuration for Router 0:

R0>en
R0#conf t
R0(config)#int lo0 //loopback interface
R0(config-if)#ip add 10.1.1.1 255.255.255.0
R0(config-if)#no shut

R0(config-if)#int s0/0
R0(config-if)#ip address 10.1.12.1 255.255.255.0
R0(config-if)#no shut

R0(config-if)#int s0/1
R0(config-if)#ip address 10.1.14.1 255.255.255.0
R0(config-if)#no shut
R0(config-if)#end
R0#wr

RIP Configuration Commands for R0:

R0>en
R0#conf t
R0(config)#router rip
R0(config-router)#net 10.0.0.0
R0(config-router)#
R0(config-router)#end
R0#show ip route

Configuration for R1:

R1>en
R1#conf t
R1(config)#int lo0 //loopback interface
R1(config-if)#ip add 10.1.2.1 255.255.255.0
R1(config-if)#no shut

R1(config-if)#int s0/1
R1(config-if)#ip address 10.1.23.1 255.255.255.0
R1(config-if)#no shut

R1(config-if)#int s0/0
R1(config-if)#ip address 10.1.12.2 255.255.255.0
R1(config-if)#no shut

R1(config-if)#end
R1#wr

RIP Configuration Commands for R1:

R1>en
R1#conf t
R1(config)#router rip
R1(config-router)#net 10.0.0.0
R1(config-router)#
R1(config-router)#end
R1#show ip route

Configuration for R2:

R2>en
R2#conf t
R2(config)#int lo0 //loopback interface
R2(config-if)#ip add 10.1.3.1 255.255.255.0
R2(config-if)#no shut
R2(config-if)#int s0/0
R2(config-if)#ip address 10.1.23.2 255.255.255.0
R2(config-if)#no shut

R2(config-if)#int s0/1
R2(config-if)#ip address 10.1.34.1 255.255.255.0
R2(config-if)#no shut

R2(config-if)#end
R2#wr
R2#en
R2#sh ip route

RIP Configuration Commands for R2:

R2>en
R2#conf t
R2(config)#router rip
R2(config-router)#net 10.0.0.0
R2(config-router)#
R2(config-router)#end
R2#show ip route

Configuration for R3:

R3>en
R3#conf t
R3(config)#int lo0 //loopback interface
R3(config-if)#int s0/0
R3(config-if)#ip add 10.1.34.2 255.255.255.0
R3(config-if)#no shut

R3(config-if)#int s0/1
R3(config-if)#ip address 10.1.14.2 255.255.255.0
R3(config-if)#no shut
R3(config-if)#end
R3#wr
R3#show ip route

RIP Configuration Commands for R3:

R3>en
R3#conf t
R3(config)#router rip
R3(config-router)#net 10.0.0.0
R3(config-router)#
R3(config-router)#end
R3#show ip route

You might also like