PROPOSED 2-

STOREY
RESIDENTIAL
BLOCK 7, LOT 1, REMEDIOS ST. BRGY. DALIG,
ANTIPOLO CITY

This report discusses the load criteria, combinations and member fixity of the
PROPOSED 2-STOREY RESIDENTIAL. The structure utilized reinforced concrete
members and designed using NCSP 2015 Provisions and ACI Code.
PROPOSED 2-STOREY
RESIDENTIAL
BLOCK 7, LOT 1, REMEDIOS ST. BRGY. DALIG,
ANTIPOLO CITY

STRUCTURAL
CALCULATION REPORT
OCTOBER 2023
This report discusses briefly the design, criteria, assumptions, and design calculation
of the structural members for the PROPOSED 2-STOREY RESIDENTIAL. The
analysis was carried out using ETABS. The load cases and combinations are based
on the latest edition of The National Structural Code of the Philippines.
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
LOCATION: BLOCK 7, LOT 1, REMEDIOS ST. BRGY. DALIG, ANTIPOLO CITY DATE: 17/10/2023
OWNER: GIANFRANCO L. FILART SHEET NO.: 1

DESIGN BRIEF
A. DESIGN CONCEPT
The structure shall be modeled as three - dimensional space frame using
Structural Analysis and Design software (STAAD ProV8i) or Extended Three-Dimensional
Analysis for Building System (ETABS) or RAM Structural System (RAM).

B. CODE AND REFERENCE

NSCP 7th Edition. National Structural Code of the Philippines 2015. Volume 1

C. DESIGN LOADS
I. Dead Load
Unit Weight of Concrete = 23.54 kN/m³
Unit Weight of Light Weight Concrete = 16.50 kN/m³
Unit Weight of Steel = 77.30 kN/m³

II. Live Load

Roof Live (Rafter) = 1.00 kPa
Roof Live (Purlin) = 1.00 kPa
Floor Live (Residential) = 1.90 kPa

III. Wind Load/ Static Seismic Load

Conforming to the requirements of the National Structural Code of the
Philippines (NSCP) Volume 1, 7th Edition, 2015.

E. DESIGN LOAD COMBINATIONS

The combination of load and forces listed below are besed on Section 203
of NSCP. This shall be considered for the design of all structural members.

I. Service II. Ultimate

DL 1.4DL 0.9DL + 1.6WL
DL + LL 1.2DL + 1.6LL + 0.5LR 0.9DL + EQh + EQv
DL + LR 1.2DL + 1.6LR + 0.8WL
DL + 0.75(LL+ LR) 1.2DL + 1.6LR + LL
DL +WL 1.2DL + 1.6WL + LL + 0.5LR
DL + (EQh + EQv)/1.4 1.2DL + EQh + EQv + LL

F. MATERIAL PROPERTIES AND STRENGTH

I. Concrete
Modulus of Elasticity = 21383.71 MPa
Poisson Ratio = 0.17
Allowable compressive strength after 28 days
Column & Beam = 20.70 MPa
Slab = 20.70 MPa
Footing = 20.70 MPa
CHB = 2.70 MPa

II. Structural Steel

Modulus of Elasticity = 200000 MPa
Poisson Ratio = 0.30
Reinforcing Bars
ø > 12 mm = 414 MPa
ø ≤ 12 mm = 276 MPa
Yield Strength = 414 Mpa

E. FOUNDATION
Allowable Soil Bearing Capacity (Assumed) = 150 kPa
 ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm
October 17, 2023 10:31 PAGE 1

S T O R Y D A T A

STORY SIMILAR TO HEIGHT ELEVATION

RF None 3000.000 7500.000

2F None 3000.000 4500.000
GF None 1500.000 1500.000
BASE None 0.000

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 2

S T A T I C L O A D C A S E S

STATIC CASE AUTO LAT SELF WT NOTIONAL

NOTIONAL
CASE TYPE LOAD MULTIPLIER FACTOR
DIRECTION

DEAD DEAD N/A 1.0000

LIVE LIVE N/A 0.0000
SDEAD SUPER DEAD N/A 0.0000
EQXPE QUAKE UBC97 0.0000
EQYPE QUAKE UBC97 0.0000

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 3

A U T O S E I S M I C U B C 9 7
Case: EQXPE

AUTO SEISMIC INPUT DATA

Direction: X + EccY
Typical Eccentricity = 5%
Eccentricity Overrides: No

Period Calculation: Program Calculated

Ct = 0.03 (in feet units)

Top Story: RF
Bottom Story: GF

R = 8.5
I = 1
hn = 6000.000 (Building Height)

1
 Soil Profile Type = SD
Z = 0.4
Ca = 0.4400
Cv = 0.6400

Seismic Source Type = A

Distance to Source = 15 km
Na = 1.0000
Nv = 1.0000

AUTO SEISMIC CALCULATION FORMULAS

Ta = Ct (hn^(3/4))

If Z >= 0.35 (Zone 4) then: If Tetabs <= 1.30 Ta then T

= Tetabs, else T = 1.30 Ta
If Z < 0.35 (Zone 1, 2 or 3) then: If Tetabs <= 1.40 Ta then T
= Tetabs, else T = 1.40 Ta

V = (Cv I W) / (R T)
(Eqn. 1)
V <= 2.5 Ca I W / R
(Eqn. 2)
V >= 0.11 Ca I W
(Eqn. 3)
V >= 0.8 Z Nv I W / R, if Z = 0.40 and Ca & Cv from code
(Eqn. 4)

If T <= 0.7 sec, then Ft = 0

If T > 0.7 sec, then Ft = 0.07 T V <= 0.25 V

AUTO SEISMIC CALCULATION RESULTS

Ta = 0.2804 sec
T Used = 0.3645 sec
W Used = 3124531.97

V (Eqn 1) = 0.2066W
V (Eqn 2) = 0.1294W
V (Eqn 3) = 0.0484W
V (Eqn 4) = 0.0376W

V Used = 0.1294W = 404351.20

Ft Used = 0.00

AUTO SEISMIC STORY FORCES

STORY FX FY FZ MX

2
MY MZ

RF 134954.25 0.00 0.00 0.000

0.000 -82322095.3
2F 269396.94 0.00 0.00 0.000
0.000-152614900.0
GF 0.00 0.00 0.00 0.000
0.000 0.000

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 4

A U T O S E I S M I C U B C 9 7
Case: EQYPE

AUTO SEISMIC INPUT DATA

Direction: Y + EccX
Typical Eccentricity = 5%
Eccentricity Overrides: No

Period Calculation: Program Calculated

Ct = 0.03 (in feet units)

Top Story: RF
Bottom Story: GF

R = 8.5
I = 1
hn = 6000.000 (Building Height)

Soil Profile Type = SD

Z = 0.4
Ca = 0.4400
Cv = 0.6400

Seismic Source Type = A

Distance to Source = 15 km
Na = 1.0000
Nv = 1.0000

AUTO SEISMIC CALCULATION FORMULAS

Ta = Ct (hn^(3/4))

If Z >= 0.35 (Zone 4) then: If Tetabs <= 1.30 Ta then T

= Tetabs, else T = 1.30 Ta
If Z < 0.35 (Zone 1, 2 or 3) then: If Tetabs <= 1.40 Ta then T
= Tetabs, else T = 1.40 Ta

3
 V = (Cv I W) / (R T)
(Eqn. 1)
V <= 2.5 Ca I W / R
(Eqn. 2)
V >= 0.11 Ca I W
(Eqn. 3)
V >= 0.8 Z Nv I W / R, if Z = 0.40 and Ca & Cv from code
(Eqn. 4)

If T <= 0.7 sec, then Ft = 0

If T > 0.7 sec, then Ft = 0.07 T V <= 0.25 V

AUTO SEISMIC CALCULATION RESULTS

Ta = 0.2804 sec
T Used = 0.3645 sec
W Used = 3124531.97

V (Eqn 1) = 0.2066W
V (Eqn 2) = 0.1294W
V (Eqn 3) = 0.0484W
V (Eqn 4) = 0.0376W

V Used = 0.1294W = 404351.20

Ft Used = 0.00

AUTO SEISMIC STORY FORCES

STORY FX FY FZ MX
MY MZ

RF 0.00 134954.25 0.00 0.000

0.000124287978.63
2F 0.00 269396.94 0.00 0.000
0.000219684676.65
GF 0.00 0.00 0.00 0.000
0.000 0.000

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 5

M A S S S O U R C E D A T A

MASS LATERAL LUMP MASS

FROM MASS ONLY AT STORIES

Loads Yes Yes

4
 M A S S S O U R C E L O A D S

LOAD MULTIPLIER

DEAD 1.0000
LIVE 0.1000
SDEAD 1.0000

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 6

D I A P H R A G M M A S S D A T A

STORY DIAPHRAGM MASS-X MASS-Y MMI

X-M Y-M

RF D1 6.382E+01 6.382E+01 3.133E+09

8933.805 6198.424
2F D1 2.471E+02 2.471E+02 1.107E+10
8752.972 6013.591

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 7

A S S E M B L E D P O I N T M A S S E S

STORY UX UY UZ RX
RY RZ

RF 6.382E+01 6.382E+01 0.000E+00 0.000E+00

0.000E+00 3.133E+09
2F 2.548E+02 2.548E+02 0.000E+00 0.000E+00
0.000E+00 1.107E+10
GF 8.476E+01 8.476E+01 0.000E+00 0.000E+00
0.000E+00 0.000E+00
BASE 3.442E+00 3.442E+00 0.000E+00 0.000E+00
0.000E+00 0.000E+00
Totals 4.068E+02 4.068E+02 0.000E+00 0.000E+00
0.000E+00 1.421E+10

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 8

C E N T E R S O F C U M U L A T I V E M A S S & C E N
T E R S O F R I G I D I T Y

STORY DIAPHRAGM /----------CENTER OF MASS----------//--

CENTER OF RIGIDITY--/
LEVEL NAME MASS ORDINATE-X ORDINATE-Y
ORDINATE-X ORDINATE-Y

RF D1 6.382E+01 8933.805 6198.424

5
8724.767 6308.739
2F D1 3.109E+02 8790.087 6051.526
8722.872 6268.157

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 9

MODAL INFORMATION

Modal Analysis not done.

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 10

TOTAL REACTIVE FORCES (RECOVERED LOADS) AT ORIGIN

LOAD FX FY FZ MX
MY MZ

DEAD 2.693E-10 -8.124E-09 1.862E+06 1.150E+

10 -1.655E+10 -9.433E-05
LIVE 8.501E-11 -3.316E-09 5.824E+05 3.437E+
09 -5.171E+09 -3.965E-05
SDEAD 3.938E-10 -1.076E-08 2.137E+06 1.317E+
10 -1.827E+10 -1.221E-04
EQXPE -4.044E+05 -1.839E-08 -1.746E-10
8.488E-05 -2.224E+09 2.691E+09
EQYPE -1.235E-09 -4.044E+05 -2.765E-10 2.224E+
09 -4.053E-06 -3.908E+09

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 11

S T O R Y F O R C E S

STORY LOAD P VX VY
T MX MY

RF EQXPE -2.456E-11 -1.350E+05 -1.249E-09

9.188E+08 3.688E-06 -4.049E+08
2F EQXPE -9.823E-11 -4.044E+05 -1.809E-08
2.691E+09 5.731E-05 -1.618E+09
GF EQXPE -1.746E-10 -4.044E+05 -1.839E-08
2.691E+09 8.488E-05 -2.224E+09
RF EQYPE -2.274E-10 -2.174E-10 -1.350E+
05 -1.330E+09 4.049E+08 9.835E-07
2F EQYPE -3.492E-10 -1.303E-09 -4.044E+
05 -3.908E+09 1.618E+09 -8.345E-07
GF EQYPE -2.765E-10 -1.235E-09 -4.044E+
05 -3.908E+09 2.224E+09 -4.053E-06

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

6
October 17, 2023 10:31 PAGE 12

STORY DRIFTS

STORY DIRECTION LOAD MAX DRIFT

RF X EQXPE 1/311
2F X EQXPE 1/147
GF X EQXPE 1/140
RF Y EQYPE 1/616
2F Y EQYPE 1/330
GF Y EQYPE 1/292

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 13

DISPLACEMENTS AT DIAPHRAGM CENTER OF MASS

STORY DIAPHRAGM LOAD UX UY

RZ

RF D1 EQXPE
38.0864 -0.6849 -0.00014
2F D1 EQXPE
29.5179 -0.5080 -0.00011
RF D1 EQYPE -0.6165 15.7635
0.00036
2F D1 EQYPE -0.4338 11.7210
0.00026

ETABS v9.7.4 File:PROPOSED 2-STOREY RESIDENTIAL Units:N-mm

October 17, 2023 10:31 PAGE 14

STORY MAXIMUM AND AVERAGE LATERAL DISPLACEMENTS

STORY LOAD DIR MAXIMUM AVERAGE RATIO

RF EQXPE X 38.7213 38.1280 1.016

2F EQXPE X 30.0256 29.5695 1.015
RF EQYPE Y 19.1062 15.8371 1.206
2F EQYPE Y 14.2332 11.8230 1.204

7
 ACI 318-08/IBC 2009
Concrete Frame Design Report

Prepared by

Model Name: PROPOSED 2-STOREY RESIDENTIAL.edb

17 October 2023
Concrete Column Design - P-M-M Interaction & Shear Design
Concrete Column Design - P-M-M Interaction & Shear Design
Story Column Section Column PMM Ratio Flexural Shear22 Shear33
Level Line Name End or Rebar % Rebar Area Rebar Area Rebar Area
RF C1 3C-200X500-10-20D Top 0.311 3140.000 0.448 0.429
RF C1 3C-200X500-10-20D Bottom 0.726 3140.000 0.448 0.429
2F C1 3C-200X500-10-20D Top 0.619
2F C1 3C-200X500-10-20D Bottom 0.508 3140.000 0.629 0.531
GF C1 3C-200X500-10-20D Top 0.301 3140.000 0.205 0.596
GF C1 3C-200X500-10-20D Bottom 0.474 3140.000 0.205 0.596
RF C2 3C-200X500-10-20D Top 0.458 3140.000 0.721 0.533
RF C2 3C-200X500-10-20D Bottom 0.859 3140.000 0.721 0.533
2F C2 3C-200X500-10-20D Top 0.979
2F C2 3C-200X500-10-20D Bottom 0.912 3140.000 0.729 0.000
GF C2 3C-200X500-10-20D Top 0.814
GF C2 3C-200X500-10-20D Bottom 0.628 3140.000 0.000 0.000
RF C3 2C-200X500-10-16D Top 0.395 2010.000 0.746 0.453
RF C3 2C-200X500-10-16D Bottom 0.759 2010.000 0.746 0.453
2F C3 2C-200X500-10-16D Top 0.596
2F C3 2C-200X500-10-16D Bottom 0.600 2010.000 0.693 0.000
GF C3 2C-200X500-10-16D Top 0.457 2010.000 0.000 0.000
GF C3 2C-200X500-10-16D Bottom 0.221 2010.000 0.000 0.000
RF C4 3C-200X500-10-20D Top 0.168 3140.000 0.728 0.546
RF C4 3C-200X500-10-20D Bottom 0.129 3140.000 0.728 0.546
2F C4 3C-200X500-10-20D Top 0.292
2F C4 3C-200X500-10-20D Bottom 0.225 3140.000 0.736 0.000
GF C4 3C-200X500-10-20D Top 0.030
GF C4 3C-200X500-10-20D Bottom 0.052 3140.000 0.000 0.000
RF C5 3C-200X500-10-20D Top 0.256 3140.000 0.488 0.427
RF C5 3C-200X500-10-20D Bottom 0.568 3140.000 0.488 0.427
2F C5 3C-200X500-10-20D Top 0.420
2F C5 3C-200X500-10-20D Bottom 0.708 3140.000 0.665 0.505
GF C5 3C-200X500-10-20D Top 0.784 3140.000 0.298 0.574
GF C5 3C-200X500-10-20D Bottom 0.434 3140.000 0.298 0.574
RF C6 1C-200X400-6-16D Top 0.420 1608.000 0.414 0.078
RF C6 1C-200X400-6-16D Bottom 0.454 1608.000 0.414 0.078
2F C6 1C-200X400-6-16D Top 0.580 1608.000 0.359 0.391
2F C6 1C-200X400-6-16D Bottom 0.121 1608.000 0.359 0.391
GF C6 1C-200X400-6-16D Top 0.437 1608.000 0.487 0.595
GF C6 1C-200X400-6-16D Bottom 0.030 1608.000 0.487 0.553
RF C7 3C-200X500-10-20D Top 0.877 3140.000 0.414 0.450
RF C7 3C-200X500-10-20D Bottom 0.147 3140.000 0.414 0.450
2F C7 3C-200X500-10-20D Top 0.397
2F C7 3C-200X500-10-20D Bottom 0.425 3140.000 0.000 0.000
GF C7 3C-200X500-10-20D Top 0.517 3140.000 0.000 0.000
GF C7 3C-200X500-10-20D Bottom 0.882 3140.000 0.000 0.000
RF C8 4C-225X400-8-20D Top 0.425 2512.000 0.507 0.042
RF C8 4C-225X400-8-20D Bottom 0.803 2512.000 0.507 0.042
2F C8 4C-225X400-8-20D Top 0.277 2512.000 0.577 0.499
2F C8 4C-225X400-8-20D Bottom 0.280 2512.000 0.577 0.499

Page 2
 Concrete Column Design - P-M-M Interaction & Shear Design
Story Column Section Column PMM Ratio Flexural Shear22 Shear33
Level Line Name End or Rebar % Rebar Area Rebar Area Rebar Area
GF C8 4C-225X400-8-20D Top 0.335 2512.000 0.000 0.000
GF C8 4C-225X400-8-20D Bottom 0.440 2512.000 0.000 0.000
RF C9 3C-200X500-10-20D Top 0.955 3140.000 0.435 0.488
RF C9 3C-200X500-10-20D Bottom 0.747 3140.000 0.435 0.488
2F C9 3C-200X500-10-20D Top 0.831
2F C9 3C-200X500-10-20D Bottom 0.846 3140.000 0.000 0.000
GF C9 3C-200X500-10-20D Top 0.893 3140.000 0.000 0.000
GF C9 3C-200X500-10-20D Bottom 0.269 3140.000 0.000 0.000
RF C10 1C-200X400-6-16D Top 0.017 1608.000 0.521 0.076
RF C10 1C-200X400-6-16D Bottom 0.848 1608.000 0.521 0.076
2F C10 1C-200X400-6-16D Top 0.760 1608.000 0.510 0.375
2F C10 1C-200X400-6-16D Bottom 0.408 1608.000 0.510 0.375
GF C10 1C-200X400-6-16D Top 0.968 1608.000 0.612 0.560
GF C10 1C-200X400-6-16D Bottom 0.551 1608.000 0.612 0.560
RF C11 2C-200X500-10-16D Top 0.230 2010.000 0.385 0.473
RF C11 2C-200X500-10-16D Bottom 0.319 2010.000 0.385 0.473
2F C11 2C-200X500-10-16D Top 0.013 2010.000 0.337 0.992
2F C11 2C-200X500-10-16D Bottom 0.028 2010.000 0.337 0.557
GF C11 2C-200X500-10-16D Top 0.574 2010.000 0.413 0.704
GF C11 2C-200X500-10-16D Bottom 0.119 2010.000 0.413 0.704
RF C12 2C-200X500-10-16D Top 0.510 2010.000 0.418 0.542
RF C12 2C-200X500-10-16D Bottom 0.364 2010.000 0.418 0.542
2F C12 2C-200X500-10-16D Top 0.593 2010.000 0.000 0.000
2F C12 2C-200X500-10-16D Bottom 0.400 2010.000 0.000 0.000
GF C12 2C-200X500-10-16D Top 0.129 2010.000 0.000 0.000
GF C12 2C-200X500-10-16D Bottom 0.624 2010.000 0.000 0.000
RF C13 2C-200X500-10-16D Top 0.836 2010.000 0.402 0.483
RF C13 2C-200X500-10-16D Bottom 0.133 2010.000 0.402 0.483
2F C13 2C-200X500-10-16D Top 0.283 2010.000 0.000 0.000
2F C13 2C-200X500-10-16D Bottom 0.514 2010.000 0.000 0.000
GF C13 2C-200X500-10-16D Top 0.067 2010.000 0.000 0.000
GF C13 2C-200X500-10-16D Bottom 0.112 2010.000 0.000 0.000
RF C14 3C-200X500-10-20D Top 0.483 3140.000 0.457 0.724
RF C14 3C-200X500-10-20D Bottom 0.922 3140.000 0.457 0.724
2F C14 3C-200X500-10-20D Top 0.185 3140.000 0.000 0.000
2F C14 3C-200X500-10-20D Bottom 0.842 3140.000 0.000 0.000
GF C14 3C-200X500-10-20D Top 0.442 3140.000 0.000 0.000
GF C14 3C-200X500-10-20D Bottom 0.339 3140.000 0.000 0.000
RF C15 3C-200X500-10-20D Top 0.293 3140.000 0.485 0.468
RF C15 3C-200X500-10-20D Bottom 0.172 3140.000 0.485 0.468
2F C15 3C-200X500-10-20D Top 0.688 3140.000 0.474 1.030
2F C15 3C-200X500-10-20D Bottom 0.728 3140.000 0.474 1.030
GF C15 3C-200X500-10-20D Top 0.121 3140.000 0.579 0.650
GF C15 3C-200X500-10-20D Bottom 0.302 3140.000 0.579 0.650
RF C16 1C-200X400-6-16D Top 0.998 1608.000 0.382 0.381
RF C16 1C-200X400-6-16D Bottom 0.360 1608.000 0.382 0.381
2F C16 1C-200X400-6-16D Top 0.943 1608.000 0.296 0.756
2F C16 1C-200X400-6-16D Bottom 0.191 1608.000 0.296 0.756

Page 3
 Concrete Column Design - P-M-M Interaction & Shear Design
Story Column Section Column PMM Ratio Flexural Shear22 Shear33
Level Line Name End or Rebar % Rebar Area Rebar Area Rebar Area
GF C16 1C-200X400-6-16D Top 0.581 1608.000 0.252 0.560
GF C16 1C-200X400-6-16D Bottom 0.514 1608.000 0.252 0.560
RF C17 2C-200X500-10-16D Top 0.473 2010.000 0.450 0.417
RF C17 2C-200X500-10-16D Bottom 0.069 2010.000 0.450 0.417
2F C17 2C-200X500-10-16D Top 0.389 2010.000 0.313 0.068
2F C17 2C-200X500-10-16D Bottom 0.541 2010.000 0.313 0.068
GF C17 2C-200X500-10-16D Top 0.442 2010.000 0.229 0.073
GF C17 2C-200X500-10-16D Bottom 0.845 2010.000 0.229 0.073
RF C18 2C-200X500-10-16D Top 0.687 2010.000 0.437 0.409
RF C18 2C-200X500-10-16D Bottom 0.244 2010.000 0.437 0.409
2F C18 2C-200X500-10-16D Top 0.812 2010.000 0.281 1.039
2F C18 2C-200X500-10-16D Bottom 0.465 2010.000 0.281 1.039
GF C18 2C-200X500-10-16D Top 0.444 2010.000 0.246 0.066
GF C18 2C-200X500-10-16D Bottom 0.186 2010.000 0.246 0.066
RF C19 2C-200X500-10-16D Top 0.842 2010.000 0.468 0.642
RF C19 2C-200X500-10-16D Bottom 0.212 2010.000 0.468 0.642
2F C19 2C-200X500-10-16D Top 0.066 2010.000 0.346 0.019
2F C19 2C-200X500-10-16D Bottom 0.291 2010.000 0.346 0.019
GF C19 2C-200X500-10-16D Top 0.358 2010.000 0.272 0.010
GF C19 2C-200X500-10-16D Bottom 0.352 2010.000 0.272 0.010
RF C20 1C-200X400-6-16D Top 0.593 1608.000 0.498 0.386
RF C20 1C-200X400-6-16D Bottom 0.741 1608.000 0.498 0.386
2F C20 1C-200X400-6-16D Top 0.906 1608.000 0.366 0.802
2F C20 1C-200X400-6-16D Bottom 0.996 1608.000 0.366 0.453
GF C20 1C-200X400-6-16D Top 0.735 1608.000 0.383 0.408
GF C20 1C-200X400-6-16D Bottom 0.269 1608.000 0.383 0.408

Concrete Column Joint Design - Beam to Column D/C Ratios & Joint Shear Check
Concrete Column Joint Design - Beam to Column D/C Ratios & Joint Shear Check
Story Column Section (6/5)Beam-Column (6/5)Beam-Column Joint Shear Joint Shear
Level Line Name Ratio Major Ratio Minor Ratio Major Ratio Minor
RF C1 3C-200X500-10-20D 0.286 0.450 0.389 0.316
2F C1 3C-200X500-10-20D 0.310 0.418 0.207 0.313
GF C1 3C-200X500-10-20D 0.997 0.059 0.127 0.227
RF C2 3C-200X500-10-20D 0.324 0.405 0.878 0.217
2F C2 3C-200X500-10-20D 0.657 0.740 0.956 0.396
GF C2 3C-200X500-10-20D 0.711 0.572 0.345 0.546
RF C3 2C-200X500-10-16D 0.961 0.547 0.191 0.909
2F C3 2C-200X500-10-16D 0.225 0.956 0.833 0.962
GF C3 2C-200X500-10-16D 0.821 0.608 0.675 0.690
RF C4 3C-200X500-10-20D 0.163 0.266 0.962 0.293
2F C4 3C-200X500-10-20D 0.764 0.766 0.530 0.069
GF C4 3C-200X500-10-20D 0.356 0.497 0.912 0.824
RF C5 3C-200X500-10-20D 0.371 0.954 0.458 0.201
2F C5 3C-200X500-10-20D 0.866 0.250 0.870 0.532
GF C5 3C-200X500-10-20D 0.488 0.110 0.457 0.992
RF C6 1C-200X400-6-16D 0.665 0.015 0.922 0.995

Page 4
 Concrete Column Joint Design - Beam to Column D/C Ratios & Joint Shear Check
Story Column Section (6/5)Beam-Column (6/5)Beam-Column Joint Shear Joint Shear
Level Line Name Ratio Major Ratio Minor Ratio Major Ratio Minor
2F C6 1C-200X400-6-16D 0.478 0.850 0.408 0.795
GF C6 1C-200X400-6-16D 0.879 0.799 0.339 0.917
RF C7 3C-200X500-10-20D 0.460 0.338 0.248 0.769
2F C7 3C-200X500-10-20D 0.902 0.166 0.546 0.134
GF C7 3C-200X500-10-20D 0.749 0.525 0.760 0.329
RF C8 4C-225X400-8-20D 0.798 0.001 0.176 0.935
2F C8 4C-225X400-8-20D 0.951 0.525 0.642 0.357
GF C8 4C-225X400-8-20D 0.913 0.662 0.645 0.654
RF C9 3C-200X500-10-20D 0.252 0.578 0.325 0.972
2F C9 3C-200X500-10-20D 0.886 0.130 0.923 0.193
GF C9 3C-200X500-10-20D 0.182 0.552 0.392 0.503
RF C10 1C-200X400-6-16D 0.913 0.867 0.246 0.199
2F C10 1C-200X400-6-16D 0.858 0.460 0.452 0.759
GF C10 1C-200X400-6-16D 0.508 0.803 0.972 0.977
RF C11 2C-200X500-10-16D 0.976 0.045 0.480 0.504
2F C11 2C-200X500-10-16D 0.943 0.798 0.184 0.166
GF C11 2C-200X500-10-16D 0.444 0.542 0.884 0.132
RF C12 2C-200X500-10-16D 0.836 0.516 0.575 0.646
2F C12 2C-200X500-10-16D 0.410 0.278 0.869 0.303
GF C12 2C-200X500-10-16D 0.490 0.785 0.593 0.059
RF C13 2C-200X500-10-16D 0.909 0.766 0.804 0.743
2F C13 2C-200X500-10-16D 0.113 0.379 0.009 0.471
GF C13 2C-200X500-10-16D 0.451 0.757 0.453 0.568
RF C14 3C-200X500-10-20D 0.870 0.600 0.131 0.800
2F C14 3C-200X500-10-20D 0.215 0.879 0.238 0.199
GF C14 3C-200X500-10-20D 0.627 0.399 0.214 0.566
RF C15 3C-200X500-10-20D 0.915 0.210 0.740 0.976
2F C15 3C-200X500-10-20D 0.936 0.193 0.887 0.357
GF C15 3C-200X500-10-20D 0.348 0.997 0.127 0.991
RF C16 1C-200X400-6-16D 0.641 0.646 0.597 0.987
2F C16 1C-200X400-6-16D 0.524 0.657 0.657 0.335
GF C16 1C-200X400-6-16D 0.484 0.750 0.805 0.567
RF C17 2C-200X500-10-16D 0.708 0.658 0.604 0.938
2F C17 2C-200X500-10-16D 0.490 0.516 0.349 0.165
GF C17 2C-200X500-10-16D 0.016 0.983 0.219 0.508
RF C18 2C-200X500-10-16D 0.157 0.482 0.747 0.045
2F C18 2C-200X500-10-16D 0.869 0.565 0.929 0.648
GF C18 2C-200X500-10-16D 0.408 0.131 0.625 0.216
RF C19 2C-200X500-10-16D 0.396 0.104 0.979 0.855
2F C19 2C-200X500-10-16D 0.076 0.035 0.082 0.562
GF C19 2C-200X500-10-16D 0.960 0.307 0.409 0.763
RF C20 1C-200X400-6-16D 0.560 0.902 0.415 0.363
2F C20 1C-200X400-6-16D 0.407 0.910 0.546 0.584
GF C20 1C-200X400-6-16D 0.319 0.946 0.537 0.733

Page 5
Concrete Beam Design - Flexural & Shear Design Rebar Areas
Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
RF B1 G200X400 End-I 12.058 59.305 0.000
RF B1 G200X400 Middle 12.058 78.975 0.000
RF B1 G200X400 End-J 48.463 33.162 0.000
RF B2 G200X400 End-I 48.559 24.202 0.000
RF B2 G200X400 Middle 16.259 45.908 0.000
RF B2 G200X400 End-J 65.456 32.588 0.000
RF B3 G200X400 End-I 65.427 32.574 0.000
RF B3 G200X400 Middle 16.252 47.495 0.000
RF B3 G200X400 End-J 46.415 23.137 0.000
RF B4 G200X400 End-I 46.514 33.013 0.000
RF B4 G200X400 Middle 11.576 76.540 0.000
RF B4 G200X400 End-J 11.576 57.315 0.000
RF B5 G200X400 End-I 0.655 0.327 0.385
RF B5 G200X400 Middle 209.694 79.188 0.489
RF B5 G200X400 End-J 245.555 160.073 0.523
RF B6 G200X400 End-I 0.000 0.569 0.823
RF B6 G200X400 Middle 319.921 152.428 1.046
RF B6 G200X400 End-J 489.735 233.558 1.120
RF B7 G200X400 End-I 0.000 0.174 0.835
RF B7 G200X400 Middle 323.313 155.163 1.058
RF B7 G200X400 End-J 499.238 237.846 1.132
RF B8 G200X400 End-I 0.000 0.558 0.815
RF B8 G200X400 Middle 316.899 151.150 1.037
RF B8 G200X400 End-J 485.303 231.554 1.112
RF B9 G200X400 End-I 0.639 0.319 0.381
RF B9 G200X400 Middle 208.882 79.008 0.485
RF B9 G200X400 End-J 244.976 159.705 0.520
RF B10 G200X400 End-I 188.092 92.870 0.248
RF B10 G200X400 Middle 48.662 46.152 0.196
RF B10 G200X400 End-J 127.799 79.866 0.223
RF B11 G200X400 End-I 105.047 71.160 0.192
RF B11 G200X400 Middle 32.827 50.098 0.154
RF B11 G200X400 End-J 133.046 65.939 0.207
RF B12 G200X400 End-I 133.536 66.180 0.208
RF B12 G200X400 Middle 32.947 50.935 0.156
RF B12 G200X400 End-J 104.449 71.993 0.192
RF B13 G200X400 End-I 129.359 77.499 0.221
RF B13 G200X400 Middle 47.578 46.592 0.191
RF B13 G200X400 End-J 189.922 93.762 0.245
RF B18 G200X400 End-I 201.752 99.520 0.450
RF B18 G200X400 Middle 49.435 56.324 0.350
RF B18 G200X400 End-J 54.401 77.486 0.321
RF B19 G200X400 End-I 226.494 125.338 0.480
RF B19 G200X400 Middle 62.151 91.664 0.391
RF B19 G200X400 End-J 77.761 110.030 0.363
RF B20 G200X400 End-I 226.494 138.409 0.470
RF B20 G200X400 Middle 68.572 84.318 0.379

Page 6
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
RF B20 G200X400 End-J 85.338 98.745 0.351
RF B21 G200X400 End-I 226.494 135.105 0.594
RF B21 G200X400 Middle 66.950 93.432 0.450
RF B21 G200X400 End-J 101.186 125.834 0.445
RF B22 G200X400 End-I 226.494 112.929 0.481
RF B22 G200X400 Middle 56.044 65.022 0.379
RF B22 G200X400 End-J 92.962 101.586 0.378
RF B27 G200X400 End-I 69.189 53.221 0.172
RF B27 G200X400 Middle 33.033 40.677 0.155
RF B27 G200X400 End-J 133.893 66.355 0.207
RF B30 G200X400 End-I 77.792 58.387 0.160
RF B30 G200X400 Middle 24.698 53.695 0.131
RF B30 G200X400 End-J 99.767 49.556 0.183
RF B31 G200X400 End-I 101.754 50.536 0.187
RF B31 G200X400 Middle 25.185 55.395 0.134
RF B31 G200X400 End-J 76.131 60.700 0.160
RF B34 G200X400 End-I 143.852 71.242 0.188
RF B34 G200X400 Middle 35.455 51.626 0.146
RF B34 G200X400 End-J 75.091 55.616 0.160
RF B35 G200X400 End-I 179.160 88.514 0.555
RF B35 G200X400 Middle 44.000 59.274 0.459
RF B35 G200X400 End-J 44.741 136.523 0.364
RF B36 G200X400 End-I 226.494 112.641 0.671
RF B36 G200X400 Middle 55.903 64.913 0.536
RF B36 G200X400 End-J 66.803 140.773 0.459
RF B37 G200X400 End-I 218.126 107.475 0.634
RF B37 G200X400 Middle 53.358 65.397 0.496
RF B37 G200X400 End-J 78.547 132.646 0.453
RF B38 G200X400 End-I 226.494 123.423 0.695
RF B38 G200X400 Middle 61.209 68.004 0.555
RF B38 G200X400 End-J 89.813 159.771 0.489
RF B39 G200X400 End-I 218.218 107.520 0.635
RF B39 G200X400 Middle 53.380 69.118 0.534
RF B39 G200X400 End-J 85.958 172.942 0.438
RF B44 G200X400 End-I 202.704 99.983 0.262
RF B44 G200X400 Middle 56.653 49.663 0.210
RF B44 G200X400 End-J 127.620 83.023 0.229
RF B45 G200X400 End-I 105.784 73.700 0.194
RF B45 G200X400 Middle 33.551 51.056 0.158
RF B45 G200X400 End-J 136.021 67.400 0.210
RF B46 G200X400 End-I 134.452 67.971 0.208
RF B46 G200X400 Middle 33.169 49.330 0.155
RF B46 G200X400 End-J 113.371 74.650 0.196
RF B47 G200X400 End-I 177.862 87.881 0.249
RF B47 G200X400 Middle 61.801 96.523 0.232
RF B47 G200X400 End-J 226.494 124.625 0.274
RF B48 G200X400 End-I 173.109 85.560 0.519
RF B48 G200X400 Middle 42.540 42.652 0.430

Page 7
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
RF B48 G200X400 End-J 65.157 114.907 0.360
RF B49 G200X400 End-I 84.068 138.135 0.458
RF B49 G200X400 Middle 48.176 63.600 0.508
RF B49 G200X400 End-J 196.511 96.970 0.634
RF B50 G200X400 End-I 191.001 94.287 0.614
RF B50 G200X400 Middle 46.852 67.531 0.488
RF B50 G200X400 End-J 101.710 141.017 0.473
RF B51 G200X400 End-I 210.180 103.617 0.638
RF B51 G200X400 Middle 51.456 60.105 0.527
RF B51 G200X400 End-J 109.307 153.203 0.480
RF B52 G200X400 End-I 10.336 37.802 0.000
RF B52 G200X400 Middle 10.336 63.540 0.000
RF B52 G200X400 End-J 41.512 21.434 0.000
RF B53 G200X400 End-I 206.321 101.742 0.562
RF B53 G200X400 Middle 50.531 50.531 0.490
RF B53 G200X400 End-J 109.825 150.908 0.423
RF B54 G200X400 End-I 140.721 83.607 0.204
RF B54 G200X400 Middle 34.694 52.851 0.152
RF B54 G200X400 End-J 126.602 71.242 0.203
RF B55 G200X400 End-I 120.331 61.802 0.191
RF B55 G200X400 Middle 29.728 47.066 0.139
RF B55 G200X400 End-J 113.498 65.542 0.186
RF B56 G200X400 End-I 111.305 70.067 0.202
RF B56 G200X400 Middle 42.150 42.150 0.186
RF B56 G200X400 End-J 171.493 84.771 0.238
RF B57 G200X400 End-I 226.494 119.506 0.255
RF B57 G200X400 Middle 59.283 223.528 0.224
RF B57 G200X400 End-J 215.748 106.321 0.245
RF B63 G200X400 End-I 119.966 59.509 0.438
RF B63 G200X400 Middle 66.077 29.639 0.396
RF B63 G200X400 End-J 0.198 0.099 0.312
RF B65 G200X400 End-I 0.000 0.217 0.648
RF B65 G200X400 Middle 137.406 57.274 0.764
RF B65 G200X400 End-J 226.494 115.425 0.823
RF B67 G200X400 End-I 0.193 0.096 0.592
RF B67 G200X400 Middle 122.874 51.902 0.709
RF B67 G200X400 End-J 212.043 104.522 0.767
RF B69 G200X400 End-I 0.000 0.597 0.710
RF B69 G200X400 Middle 174.998 70.302 0.813
RF B69 G200X400 End-J 226.494 141.936 0.864
RF B70 G200X400 End-I 41.749 20.818 0.137
RF B70 G200X400 Middle 13.668 11.571 0.109
RF B70 G200X400 End-J 0.642 0.321 0.097
RF B72 G200X400 End-I 146.842 72.708 0.504
RF B72 G200X400 Middle 86.466 36.181 0.469
RF B72 G200X400 End-J 0.057 0.165 0.398
RF B73 G200X400 End-I 11.420 35.605 0.000
RF B73 G200X400 Middle 11.420 45.319 0.000

Page 8
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
RF B73 G200X400 End-J 45.887 22.875 0.000
RF B74 G200X400 End-I 45.789 22.826 0.000
RF B74 G200X400 Middle 11.396 21.921 0.000
RF B74 G200X400 End-J 43.603 21.739 0.000
RF B75 G200X400 End-I 43.674 22.233 0.097
RF B75 G200X400 Middle 22.233 22.233 0.082
RF B75 G200X400 End-J 89.719 44.595 0.108
RF B76 G200X400 End-I 89.867 44.669 0.335
RF B76 G200X400 Middle 28.469 68.426 0.302
RF B76 G200X400 End-J 28.469 115.176 0.252
RF B77 G200X400 End-I 28.462 115.149 0.107
RF B77 G200X400 Middle 28.462 101.563 0.149
RF B77 G200X400 End-J 28.462 34.437 0.177
2F B1 G200X400 End-I 97.643 226.494 0.186
2F B1 G200X400 Middle 97.643 310.692 0.000
2F B1 G200X400 End-J 305.349 197.894 0.496
2F B2 G200X400 End-I 305.185 197.791 0.449
2F B2 G200X400 Middle 108.929 186.305 0.039
2F B2 G200X400 End-J 342.460 221.124 0.450
2F B3 G200X400 End-I 341.978 220.824 0.451
2F B3 G200X400 Middle 108.784 216.574 0.040
2F B3 G200X400 End-J 301.618 195.547 0.446
2F B4 G200X400 End-I 302.237 195.937 0.481
2F B4 G200X400 Middle 96.691 296.079 0.000
2F B4 G200X400 End-J 96.691 226.494 0.176
2F B5 G200X400 End-I 0.744 0.372 1.544
2F B5 G200X400 Middle 640.305 226.494 1.807
2F B5 G200X400 End-J 960.102 436.116 1.894
2F B6 G200X500 End-I 0.000 0.852 O/S
2F B6 G200X500 Middle 1251.205 380.064 O/S
2F B6 G200X500 End-J 1702.618 809.003 O/S
2F B7 G200X500 End-I 0.522 0.261 O/S
2F B7 G200X500 Middle 1153.547 351.338 O/S
2F B7 G200X500 End-J 1582.582 743.593 O/S
2F B8 G200X500 End-I 0.000 0.849 O/S
2F B8 G200X500 Middle 1241.250 376.876 O/S
2F B8 G200X500 End-J 1689.346 801.699 O/S
2F B9 G200X400 End-I 0.815 0.407 1.528
2F B9 G200X400 Middle 640.234 226.494 1.804
2F B9 G200X400 End-J 962.424 437.243 1.893
2F B10 G200X450 End-I 492.716 414.322 0.958
2F B10 G200X450 Middle 168.991 366.456 0.619
2F B10 G200X450 End-J 541.508 259.802 0.754
2F B11 G200X450 End-I 445.968 259.802 0.615
2F B11 G200X450 Middle 140.902 192.346 0.480
2F B11 G200X450 End-J 352.973 228.705 0.568
2F B12 G200X450 End-I 353.239 228.871 0.570
2F B12 G200X450 Middle 142.661 189.640 0.484

Page 9
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
2F B12 G200X450 End-J 451.873 259.802 0.619
2F B13 G200X450 End-I 556.235 265.409 0.612
2F B13 G200X450 Middle 173.252 378.619 0.273
2F B13 G200X450 End-J 502.945 412.983 1.025
2F B14 G200X400 End-I 0.000 0.000 0.000
2F B14 G200X400 Middle 0.000 15.520 0.000
2F B14 G200X400 End-J 0.000 0.000 0.000
2F B15 G200X400 End-I 0.000 0.000 2.152
2F B15 G200X400 Middle 401.638 198.073 O/S
2F B15 G200X400 End-J 652.637 305.634 O/S
2F B16 G200X400 End-I 652.519 305.583 O/S
2F B16 G200X400 Middle 401.567 198.041 O/S
2F B16 G200X400 End-J 0.000 0.000 2.152
2F B17 G200X400 End-I 0.000 0.000 0.000
2F B17 G200X400 Middle 0.000 17.571 0.000
2F B17 G200X400 End-J 0.000 0.000 0.000
2F B18 G200X400 End-I 355.389 226.494 0.802
2F B18 G200X400 Middle 112.831 119.023 0.626
2F B18 G200X400 End-J 143.524 169.443 0.557
2F B19 G200X500 End-I 691.749 328.297 1.403
2F B19 G200X500 Middle 213.844 213.844 1.193
2F B19 G200X500 End-J 213.844 293.110 0.917
2F B20 G200X500 End-I 863.636 403.754 1.806
2F B20 G200X500 Middle 261.497 324.455 1.593
2F B20 G200X500 End-J 314.170 261.497 1.067
2F B21 G200X500 End-I 732.899 346.605 1.630
2F B21 G200X500 Middle 225.460 225.460 1.350
2F B21 G200X500 End-J 256.398 293.110 0.997
2F B22 G200X400 End-I 376.324 226.494 0.769
2F B22 G200X400 Middle 119.115 119.115 0.690
2F B22 G200X400 End-J 195.517 226.494 0.548
2F B23 G200X450 End-I 0.000 540.612 0.477
2F B23 G200X450 Middle 0.000 778.017 0.000
2F B23 G200X450 End-J 0.000 480.967 0.455
2F B24 G200X450 End-I 95.755 20.257 0.129
2F B24 G200X450 Middle 0.000 285.445 0.000
2F B24 G200X450 End-J 41.125 47.390 0.067
2F B25 G200X450 End-I 99.191 20.025 0.124
2F B25 G200X450 Middle 0.839 280.850 0.000
2F B25 G200X450 End-J 41.800 44.793 0.065
2F B26 G200X450 End-I 0.000 562.604 0.509
2F B26 G200X450 Middle 0.000 831.254 0.000
2F B26 G200X450 End-J 0.000 511.958 0.505
2F B28 G200X400 End-I 226.494 226.494 0.646
2F B28 G200X400 Middle 447.512 226.494 1.114
2F B28 G200X400 End-J 1009.861 460.367 1.245
2F B29 G200X400 End-I 722.144 335.426 0.805
2F B29 G200X400 Middle 271.725 216.735 0.725

Page 10
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
2F B29 G200X400 End-J 216.735 216.735 0.550
2F B32 G200X400 End-I 220.276 220.276 0.555
2F B32 G200X400 Middle 279.636 220.276 0.735
2F B32 G200X400 End-J 735.542 341.099 0.814
2F B33 G200X400 End-I 1061.348 485.716 1.007
2F B33 G200X400 Middle 442.993 231.741 0.918
2F B33 G200X400 End-J 231.741 231.741 0.642
2F B35 G200X400 End-I 252.241 164.326 0.854
2F B35 G200X400 Middle 81.268 116.048 0.692
2F B35 G200X400 End-J 152.060 222.294 0.633
2F B36 G200X400 End-I 298.758 193.748 0.963
2F B36 G200X400 Middle 95.625 174.932 0.700
2F B36 G200X400 End-J 205.011 212.330 0.794
2F B37 G200X400 End-I 487.391 232.499 1.161
2F B37 G200X400 Middle 151.752 411.852 1.082
2F B37 G200X400 End-J 313.555 226.494 1.227
2F B38 G200X400 End-I 330.323 213.548 1.172
2F B38 G200X400 Middle 105.253 184.253 0.822
2F B38 G200X400 End-J 226.494 226.494 0.952
2F B39 G200X400 End-I 279.247 201.542 0.735
2F B39 G200X400 Middle 89.627 109.340 0.700
2F B39 G200X400 End-J 226.494 249.013 0.565
2F B40 G200X400 End-I 0.000 0.000 0.000
2F B40 G200X400 Middle 0.000 10.560 0.000
2F B40 G200X400 End-J 0.000 0.000 0.000
2F B41 G200X400 End-I 0.000 0.000 1.757
2F B41 G200X400 Middle 321.436 159.245 1.839
2F B41 G200X400 End-J 513.480 244.254 1.874
2F B42 G200X400 End-I 513.445 244.238 1.874
2F B42 G200X400 Middle 321.414 159.235 1.838
2F B42 G200X400 End-J 0.000 0.000 1.757
2F B43 G200X400 End-I 0.000 0.000 0.000
2F B43 G200X400 Middle 0.000 23.067 0.000
2F B43 G200X400 End-J 0.000 0.000 0.000
2F B44 G200X450 End-I 545.806 460.468 1.172
2F B44 G200X450 Middle 210.505 440.574 0.488
2F B44 G200X450 End-J 687.837 324.079 0.919
2F B45 G200X450 End-I 584.507 278.158 0.817
2F B45 G200X450 Middle 181.380 259.802 0.622
2F B45 G200X450 End-J 465.687 259.802 0.770
2F B46 G200X450 End-I 457.767 259.802 0.796
2F B46 G200X450 Middle 206.618 245.849 0.678
2F B46 G200X450 End-J 673.856 317.929 0.873
2F B47 G200X450 End-I 890.308 410.835 1.160
2F B47 G200X450 Middle 259.802 646.050 0.919
2F B47 G200X450 End-J 714.226 386.056 1.258
2F B48 G200X400 End-I 259.902 169.191 0.932
2F B48 G200X400 Middle 83.646 114.283 0.700

Page 11
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
2F B48 G200X400 End-J 188.315 209.456 0.718
2F B49 G200X400 End-I 226.494 214.250 0.891
2F B49 G200X400 Middle 97.269 135.169 0.797
2F B49 G200X400 End-J 304.125 197.124 1.098
2F B50 G200X400 End-I 351.374 226.494 1.194
2F B50 G200X400 Middle 111.621 138.506 0.894
2F B50 G200X400 End-J 226.494 226.494 0.918
2F B51 G200X400 End-I 331.959 214.570 1.099
2F B51 G200X400 Middle 105.749 134.252 0.817
2F B51 G200X400 End-J 227.787 226.494 0.919
2F B52 G200X400 End-I 0.000 100.914 0.000
2F B52 G200X400 Middle 0.000 201.230 0.000
2F B52 G200X400 End-J 0.000 100.914 0.000
2F B53 G200X400 End-I 323.296 213.998 0.973
2F B53 G200X400 Middle 103.117 123.268 0.754
2F B53 G200X400 End-J 226.494 226.494 0.784
2F B54 G200X400 End-I 350.964 226.494 0.653
2F B54 G200X400 Middle 133.857 226.494 0.521
2F B54 G200X400 End-J 425.994 226.494 0.707
2F B55 G200X400 End-I 396.459 226.494 0.671
2F B55 G200X400 Middle 125.120 189.818 0.483
2F B55 G200X400 End-J 379.139 226.494 0.660
2F B56 G200X400 End-I 369.654 226.494 0.661
2F B56 G200X400 Middle 131.267 182.067 0.503
2F B56 G200X400 End-J 417.208 226.494 0.691
2F B57 G200X450 End-I 497.761 259.802 0.576
2F B57 G200X450 Middle 156.224 278.854 0.467
2F B57 G200X450 End-J 395.598 255.373 0.541
2F B58 G200X400 End-I 160.618 79.454 1.244
2F B58 G200X400 Middle -1.000 -1.000 -1.000
2F B58 G200X400 End-J 0.322 0.161 1.155
2F B59 G200X400 End-I 0.000 0.395 O/S
2F B59 G200X400 Middle -1.000 -1.000 -1.000
2F B59 G200X400 End-J 301.122 195.236 O/S
2F B60 G200X400 End-I 0.279 0.139 2.084
2F B60 G200X400 Middle -1.000 -1.000 -1.000
2F B60 G200X400 End-J 233.150 152.168 2.165
2F B61 G200X400 End-I 0.000 0.412 O/S
2F B61 G200X400 Middle -1.000 -1.000 -1.000
2F B61 G200X400 End-J 348.540 224.912 O/S
2F B62 G200X400 End-I 203.371 100.308 1.542
2F B62 G200X400 Middle 96.051 49.823 1.496
2F B62 G200X400 End-J 0.211 0.105 1.451
2F B64 G200X400 End-I 81.957 198.131 0.000
2F B64 G200X400 Middle 81.957 226.494 0.000
2F B64 G200X400 End-J 254.459 165.736 0.180
2F B66 G200X400 End-I 255.031 166.099 0.181
2F B66 G200X400 Middle 82.135 128.369 0.000

Page 12
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
2F B66 G200X400 End-J 210.414 103.731 0.106
2F B68 G200X400 End-I 210.347 113.713 0.109
2F B68 G200X400 Middle 113.713 113.713 0.000
2F B68 G200X400 End-J 358.320 226.494 0.260
2F B71 G200X400 End-I 358.479 226.494 0.342
2F B71 G200X400 Middle 113.761 308.031 0.000
2F B71 G200X400 End-J 113.761 226.494 0.091
GF B10 G200X400 End-I 497.254 306.281 0.791
GF B10 G200X400 Middle 154.593 226.494 0.574
GF B10 G200X400 End-J 481.685 237.222 0.820
GF B11 G200X400 End-I 423.880 226.494 0.661
GF B11 G200X400 Middle 136.388 199.047 0.467
GF B11 G200X400 End-J 434.600 226.494 0.662
GF B12 G200X400 End-I 435.087 226.494 0.662
GF B12 G200X400 Middle 136.531 198.714 0.466
GF B12 G200X400 End-J 427.311 226.494 0.661
GF B13 G200X400 End-I 484.945 231.392 0.813
GF B13 G200X400 Middle 155.832 226.494 0.559
GF B13 G200X400 End-J 501.566 294.954 0.786
GF B18 G200X400 End-I 253.157 197.374 0.649
GF B18 G200X400 Middle 81.553 134.228 0.479
GF B18 G200X400 End-J 226.494 193.181 0.607
GF B19 G200X400 End-I 272.787 226.494 0.683
GF B19 G200X400 Middle 87.634 160.019 0.516
GF B19 G200X400 End-J 242.469 226.494 0.663
GF B20 G200X400 End-I 296.408 226.494 0.699
GF B20 G200X400 Middle 94.905 164.597 0.528
GF B20 G200X400 End-J 257.241 226.494 0.678
GF B21 G200X400 End-I 321.438 244.466 0.725
GF B21 G200X400 Middle 102.552 183.170 0.558
GF B21 G200X400 End-J 291.990 234.655 0.710
GF B22 G200X400 End-I 343.565 239.982 0.742
GF B22 G200X400 Middle 109.264 181.903 0.570
GF B22 G200X400 End-J 280.224 226.611 0.704
GF B27 G200X400 End-I 308.832 284.939 0.411
GF B27 G200X400 Middle 122.326 154.361 0.384
GF B27 G200X400 End-J 323.452 252.951 0.436
GF B30 G200X400 End-I 271.924 244.443 0.373
GF B30 G200X400 Middle 100.952 136.495 0.335
GF B30 G200X400 End-J 283.484 229.329 0.388
GF B31 G200X400 End-I 288.120 231.018 0.395
GF B31 G200X400 Middle 104.069 141.165 0.343
GF B31 G200X400 End-J 275.274 251.000 0.377
GF B34 G200X400 End-I 315.949 231.737 0.398
GF B34 G200X400 Middle 136.927 174.702 0.346
GF B34 G200X400 End-J 295.510 266.185 0.372
GF B35 G200X400 End-I 268.782 185.232 0.794
GF B35 G200X400 Middle 86.396 101.368 0.630

Page 13
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
GF B35 G200X400 End-J 226.494 226.494 0.645
GF B36 G200X400 End-I 311.287 226.494 0.843
GF B36 G200X400 Middle 99.458 102.413 0.683
GF B36 G200X400 End-J 226.494 233.248 0.707
GF B37 G200X400 End-I 323.454 226.494 0.853
GF B37 G200X400 Middle 103.165 107.242 0.689
GF B37 G200X400 End-J 237.502 242.620 0.722
GF B38 G200X400 End-I 362.468 242.366 0.937
GF B38 G200X400 Middle 114.961 114.961 0.778
GF B38 G200X400 End-J 272.009 281.857 0.808
GF B39 G200X400 End-I 333.520 242.024 0.772
GF B39 G200X400 Middle 106.223 106.223 0.737
GF B39 G200X400 End-J 266.263 316.115 0.702
GF B44 G200X400 End-I 427.504 349.082 0.498
GF B44 G200X400 Middle 179.488 181.960 0.446
GF B44 G200X400 End-J 347.992 307.235 0.479
GF B45 G200X400 End-I 301.709 266.564 0.406
GF B45 G200X400 Middle 117.752 140.110 0.364
GF B45 G200X400 End-J 321.761 267.383 0.417
GF B46 G200X400 End-I 326.683 271.487 0.428
GF B46 G200X400 Middle 116.575 148.176 0.376
GF B46 G200X400 End-J 304.898 278.616 0.413
GF B47 G200X400 End-I 330.371 269.867 0.406
GF B47 G200X400 Middle 195.526 189.627 0.371
GF B47 G200X400 End-J 409.756 303.963 0.426
GF B48 G200X400 End-I 282.447 224.236 0.851
GF B48 G200X400 Middle 90.614 114.276 0.699
GF B48 G200X400 End-J 226.494 239.612 0.689
GF B49 G200X400 End-I 240.451 283.973 0.777
GF B49 G200X400 Middle 100.794 127.734 0.797
GF B49 G200X400 End-J 315.668 226.494 0.946
GF B50 G200X400 End-I 335.868 234.931 0.979
GF B50 G200X400 Middle 106.934 134.587 0.830
GF B50 G200X400 End-J 272.672 306.498 0.834
GF B51 G200X400 End-I 369.834 257.329 1.060
GF B51 G200X400 Middle 117.171 144.090 0.911
GF B51 G200X400 End-J 298.423 341.783 0.895
GF B53 G200X400 End-I 382.112 274.299 1.050
GF B53 G200X400 Middle 120.845 146.577 0.897
GF B53 G200X400 End-J 313.175 347.267 0.905
GF B54 G200X400 End-I 455.280 296.872 0.777
GF B54 G200X400 Middle 150.301 226.494 0.579
GF B54 G200X400 End-J 482.364 231.940 0.825
GF B55 G200X400 End-I 440.487 226.494 0.668
GF B55 G200X400 Middle 138.114 200.526 0.472
GF B55 G200X400 End-J 432.943 226.494 0.661
GF B56 G200X400 End-I 437.246 226.494 0.746
GF B56 G200X400 Middle 146.680 196.021 0.520

Page 14
 Concrete Beam Design - Flexural & Shear Design Rebar Areas
Story Beam Section Location Top Bottom Shear
Level Bay Name Rebar Area Rebar Area Rebar Area
GF B56 G200X400 End-J 469.862 226.494 0.768
GF B57 G200X400 End-I 530.088 251.697 0.569
GF B57 G200X400 Middle 163.980 236.183 0.449
GF B57 G200X400 End-J 489.005 233.228 0.547

Concrete Beam Design - Torsion Design Rebar Areas

Concrete Beam Design - Torsion Design Rebar Areas
Story Beam Section Torsion-Shear Torsion-Long.
Level Bay Name Rebar Area Rebar Area
RF B1 G200X400 0.000 0.000
RF B2 G200X400 0.000 0.000
RF B3 G200X400 0.000 0.000
RF B4 G200X400 0.000 0.000
RF B5 G200X400 0.000 0.000
RF B6 G200X400 0.000 0.000
RF B7 G200X400 0.000 0.000
RF B8 G200X400 0.000 0.000
RF B9 G200X400 0.000 0.000
RF B10 G200X400 0.000 0.000
RF B11 G200X400 0.000 0.000
RF B12 G200X400 0.000 0.000
RF B13 G200X400 0.000 0.000
RF B18 G200X400 0.000 0.000
RF B19 G200X400 0.000 0.000
RF B20 G200X400 0.000 0.000
RF B21 G200X400 0.000 0.000
RF B22 G200X400 0.000 0.000
RF B27 G200X400 0.000 0.000
RF B30 G200X400 0.000 0.000
RF B31 G200X400 0.000 0.000
RF B34 G200X400 0.000 0.000
RF B35 G200X400 0.000 0.000
RF B36 G200X400 0.000 0.000
RF B37 G200X400 0.000 0.000
RF B38 G200X400 0.000 0.000
RF B39 G200X400 0.000 0.000
RF B44 G200X400 0.000 0.000
RF B45 G200X400 0.000 0.000
RF B46 G200X400 0.000 0.000
RF B47 G200X400 0.000 0.000
RF B48 G200X400 0.000 0.000
RF B49 G200X400 0.000 0.000
RF B50 G200X400 0.000 0.000
RF B51 G200X400 0.000 0.000
RF B52 G200X400 0.000 0.000
RF B53 G200X400 0.000 0.000
RF B54 G200X400 0.000 0.000

Page 15
 Concrete Beam Design - Torsion Design Rebar Areas
Story Beam Section Torsion-Shear Torsion-Long.
Level Bay Name Rebar Area Rebar Area
RF B55 G200X400 0.000 0.000
RF B56 G200X400 0.000 0.000
RF B57 G200X400 0.000 0.000
RF B63 G200X400 0.000 0.000
RF B65 G200X400 0.000 0.000
RF B67 G200X400 0.000 0.000
RF B69 G200X400 0.000 0.000
RF B70 G200X400 0.000 0.000
RF B72 G200X400 0.000 0.000
RF B73 G200X400 0.000 0.000
RF B74 G200X400 0.000 0.000
RF B75 G200X400 0.000 0.000
RF B76 G200X400 0.000 0.000
RF B77 G200X400 0.000 0.000
2F B1 G200X400 0.000 0.000
2F B2 G200X400 0.000 0.000
2F B3 G200X400 0.000 0.000
2F B4 G200X400 0.000 0.000
2F B5 G200X400 0.000 0.000
2F B6 G200X500 0.000 0.000
2F B7 G200X500 0.000 0.000
2F B8 G200X500 0.000 0.000
2F B9 G200X400 0.000 0.000
2F B10 G200X450 0.000 0.000
2F B11 G200X450 0.000 0.000
2F B12 G200X450 0.000 0.000
2F B13 G200X450 0.000 0.000
2F B14 G200X400 0.000 0.000
2F B15 G200X400 0.000 0.000
2F B16 G200X400 0.000 0.000
2F B17 G200X400 0.000 0.000
2F B18 G200X400 0.000 0.000
2F B19 G200X500 0.000 0.000
2F B20 G200X500 0.000 0.000
2F B21 G200X500 0.000 0.000
2F B22 G200X400 0.000 0.000
2F B23 G200X450 0.000 0.000
2F B24 G200X450 0.000 0.000
2F B25 G200X450 0.000 0.000
2F B26 G200X450 0.000 0.000
2F B28 G200X400 0.000 0.000
2F B29 G200X400 0.000 0.000
2F B32 G200X400 0.000 0.000
2F B33 G200X400 0.000 0.000
2F B35 G200X400 0.000 0.000
2F B36 G200X400 0.000 0.000
2F B37 G200X400 0.000 0.000
2F B38 G200X400 0.000 0.000

Page 16
 Concrete Beam Design - Torsion Design Rebar Areas
Story Beam Section Torsion-Shear Torsion-Long.
Level Bay Name Rebar Area Rebar Area
2F B39 G200X400 0.000 0.000
2F B40 G200X400 0.000 0.000
2F B41 G200X400 0.000 0.000
2F B42 G200X400 0.000 0.000
2F B43 G200X400 0.000 0.000
2F B44 G200X450 0.000 0.000
2F B45 G200X450 0.000 0.000
2F B46 G200X450 0.000 0.000
2F B47 G200X450 0.000 0.000
2F B48 G200X400 0.000 0.000
2F B49 G200X400 0.000 0.000
2F B50 G200X400 0.000 0.000
2F B51 G200X400 0.000 0.000
2F B52 G200X400 0.000 0.000
2F B53 G200X400 0.000 0.000
2F B54 G200X400 0.000 0.000
2F B55 G200X400 0.000 0.000
2F B56 G200X400 0.000 0.000
2F B57 G200X450 0.000 0.000
2F B58 G200X400 0.000 0.000
2F B59 G200X400 0.000 0.000
2F B60 G200X400 0.000 0.000
2F B61 G200X400 0.000 0.000
2F B62 G200X400 0.000 0.000
2F B64 G200X400 0.000 0.000
2F B66 G200X400 0.000 0.000
2F B68 G200X400 0.000 0.000
2F B71 G200X400 0.000 0.000
GF B10 G200X400 0.000 0.000
GF B11 G200X400 0.000 0.000
GF B12 G200X400 0.000 0.000
GF B13 G200X400 0.000 0.000
GF B18 G200X400 0.000 0.000
GF B19 G200X400 0.000 0.000
GF B20 G200X400 0.000 0.000
GF B21 G200X400 0.000 0.000
GF B22 G200X400 0.000 0.000
GF B27 G200X400 0.000 0.000
GF B30 G200X400 0.000 0.000
GF B31 G200X400 0.000 0.000
GF B34 G200X400 0.000 0.000
GF B35 G200X400 0.000 0.000
GF B36 G200X400 0.000 0.000
GF B37 G200X400 0.000 0.000
GF B38 G200X400 0.000 0.000
GF B39 G200X400 0.000 0.000
GF B44 G200X400 0.000 0.000
GF B45 G200X400 0.000 0.000

Page 17
 Concrete Beam Design - Torsion Design Rebar Areas
Story Beam Section Torsion-Shear Torsion-Long.
Level Bay Name Rebar Area Rebar Area
GF B46 G200X400 0.000 0.000
GF B47 G200X400 0.000 0.000
GF B48 G200X400 0.000 0.000
GF B49 G200X400 0.000 0.000
GF B50 G200X400 0.000 0.000
GF B51 G200X400 0.000 0.000
GF B53 G200X400 0.000 0.000
GF B54 G200X400 0.000 0.000
GF B55 G200X400 0.000 0.000
GF B56 G200X400 0.000 0.000
GF B57 G200X400 0.000 0.000

Page 18
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
FOOTING: F01 DATE: 17/10/2023
OWNER: GIANFRANCO L. FILART SHEET NO.: 1

ISOLATED FOOTING RECTANGULAR FOOTING

A. DESIGN INPUTS F. SOIL BEARING PRESSURE
Compressive Strength, f'c = 20.70 MPa
Yield Strength, fy = 414 MPa I. Along X
Unit Weight of Concrete = 23.54 kN/m³ qumax = 181.14 kPa
Unit Weight of Soil = 17.00 kN/m³ qumin = 181.14 kPa
øbar = 16 mm
Min. Spacing = 200 mm d II. Along Y
qumax = 181.14 kPa
qumin = 181.14 kPa
B. SIZING UP
I. Column
Length, Xc = 200 mm
Width, Yc = 400 mm
II. Footing
Ratio of Length and Width W = 1L qumin
Length, Xf = 1.10 m qumax
Width, Yf = 1.10 m G. DESIGN
Thickness, t = 250 mm Along X Along Y
Depth, D = 1.50 m Mu = (quLx²/2) 20 12 kNm
Effective depth, d = t-75-ø/2 = 167 mm Ru = Mu/(øXf d²) 0.73 0.44
C. DIAGRAM ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0018 0.0011
ρmin = 0.002 0.0020 0.0020
As = ρbd 367 367 mm²
P Number of bar, N 5.8 5.8
Number of bar, N 1.8 1.8 pc(s)
M
SAY N 6.0 6.0 pc(s)

F. SHEAR
Ly

I. Wide Beam Shear

d ø Vc = 0.75(1/6 √ f'c )(b) (d) = 104.47 kN
Vu = qu x Shear Area = 56.39 kN Safe!
Yc
Yf

Xc Lx 0.2m
t

Xf
Xf
D. LOAD CONSIDERED
I. Service Load
Load, P = 156.0 kN
0.3m
II. Ultimate Load II. Punching Shear
Load, Pu = 211 kN ø Vc = 0.75(1/3 √ f'c )(b) (d) = 354.83 kN
Vu = qu x Shear Area = 172.94 kN Safe!
III. Additional Weight
Weight of Soil = 0 kN
Weight of Footing = 7 kN
0.57m

E. SOIL CAPACITY
qallowable = SBC = 150 kPa
qactual = P/A + 6M/bd² = 134.8 kPa Safe!

0.37m
SUMMARY
Therefore Provide 6-ø16 along X
Therefore Provide 6-ø16 along Y
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
FOOTING: F02 DATE: 17/10/2023
OWNER: GIANFRANCO L. FILART SHEET NO.: 2

ISOLATED FOOTING RECTANGULAR FOOTING

A. DESIGN INPUTS F. SOIL BEARING PRESSURE
Compressive Strength, f'c = 20.70 MPa
Yield Strength, fy = 414 MPa I. Along X
Unit Weight of Concrete = 23.54 kN/m³ qumax = 214.55 kPa
Unit Weight of Soil = 17.00 kN/m³ qumin = 214.55 kPa
øbar = 16 mm
Min. Spacing = 200 mm d II. Along Y
qumax = 214.55 kPa
qumin = 214.55 kPa
B. SIZING UP
I. Column
Length, Xc = 200 mm
Width, Yc = 400 mm
II. Footing
Ratio of Length and Width W = 1L qumin
Length, Xf = 1.30 m qumax
Width, Yf = 1.30 m G. DESIGN
Thickness, t = 250 mm Along X Along Y
Depth, D = 1.50 m Mu = (quLx²/2) 42 28 kNm
Effective depth, d = t-75-ø/2 = 167 mm Ru = Mu/(øXf d²) 1.29 0.87
C. DIAGRAM ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0032 0.0021
ρmin = 0.002 0.0020 0.0020
As = ρbd 705 705 mm²
P Number of bar, N 6.8 6.8
Number of bar, N 3.5 3.5 pc(s)
M
SAY N 7.0 7.0 pc(s)

F. SHEAR
Ly

I. Wide Beam Shear

d ø Vc = 0.75(1/6 √ f'c )(b) (d) = 123.47 kN
Vu = qu x Shear Area = 106.82 kN Safe!
Yc
Yf

Xc Lx 0.3m
t

Xf
Xf
D. LOAD CONSIDERED
I. Service Load
Load, P = 237.4 kN
0.4m
II. Ultimate Load II. Punching Shear
Load, Pu = 351 kN ø Vc = 0.75(1/3 √ f'c )(b) (d) = 354.83 kN
Vu = qu x Shear Area = 306.01 kN Safe!
III. Additional Weight
Weight of Soil = 0 kN
Weight of Footing = 10 kN
0.57m

E. SOIL CAPACITY
qallowable = SBC = 150 kPa
qactual = P/A + 6M/bd² = 146.3 kPa Safe!

0.37m
SUMMARY
Therefore Provide 7-ø16 along X
Therefore Provide 7-ø16 along Y
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
FOOTING: F03 DATE: 17/10/2023
OWNER: GIANFRANCO L. FILART SHEET NO.: 3

ISOLATED FOOTING RECTANGULAR FOOTING

A. DESIGN INPUTS F. SOIL BEARING PRESSURE
Compressive Strength, f'c = 20.70 MPa
Yield Strength, fy = 414 MPa I. Along X
Unit Weight of Concrete = 23.54 kN/m³ qumax = 172.71 kPa
Unit Weight of Soil = 17.00 kN/m³ qumin = 172.71 kPa
øbar = 16 mm
Min. Spacing = 200 mm d II. Along Y
qumax = 172.71 kPa
qumin = 172.71 kPa
B. SIZING UP
I. Column
Length, Xc = 200 mm
Width, Yc = 400 mm
II. Footing
Ratio of Length and Width W = 1L qumin
Length, Xf = 1.50 m qumax
Width, Yf = 1.50 m G. DESIGN
Thickness, t = 250 mm Along X Along Y
Depth, D = 1.50 m Mu = (quLx²/2) 55 39 kNm
Effective depth, d = t-75-ø/2 = 167 mm Ru = Mu/(øXf d²) 1.45 1.04
C. DIAGRAM ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0037 0.0026
ρmin = 0.002 0.0020 0.0020
As = ρbd 919 919 mm²
P Number of bar, N 7.8 7.8
Number of bar, N 4.6 4.6 pc(s)
M
SAY N 8.0 8.0 pc(s)

F. SHEAR
Ly

I. Wide Beam Shear

d ø Vc = 0.75(1/6 √ f'c )(b) (d) = 142.46 kN
Vu = qu x Shear Area = 125.13 kN Safe!
Yc
Yf

Xc Lx 0.4m
t

Xf
Xf
D. LOAD CONSIDERED
I. Service Load
Load, P = 289.4 kN
0.5m
II. Ultimate Load II. Punching Shear
Load, Pu = 373 kN ø Vc = 0.75(1/3 √ f'c )(b) (d) = 354.83 kN
Vu = qu x Shear Area = 336.76 kN Safe!
III. Additional Weight
Weight of Soil = 0 kN
Weight of Footing = 13 kN
0.57m

E. SOIL CAPACITY
qallowable = SBC = 150 kPa
qactual = P/A + 6M/bd² = 134.5 kPa Safe!

0.37m
SUMMARY
Therefore Provide 8-ø16 along X
Therefore Provide 8-ø16 along Y
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
FOOTING: F04 DATE: 17/10/2023
OWNER: GIANFRANCO L. FILART SHEET NO.: 4

ISOLATED FOOTING RECTANGULAR FOOTING

A. DESIGN INPUTS F. SOIL BEARING PRESSURE
Compressive Strength, f'c = 20.70 MPa
Yield Strength, fy = 414 MPa I. Along X
Unit Weight of Concrete = 23.54 kN/m³ qumax = 199.55 kPa
Unit Weight of Soil = 17.00 kN/m³ qumin = 199.55 kPa
øbar = 16 mm
Min. Spacing = 200 mm d II. Along Y
qumax = 199.55 kPa
qumin = 199.55 kPa
B. SIZING UP
I. Column
Length, Xc = 200 mm
Width, Yc = 400 mm
II. Footing
Ratio of Length and Width W = 1L qumin
Length, Xf = 1.70 m qumax
Width, Yf = 1.70 m G. DESIGN
Thickness, t = 300 mm Along X Along Y
Depth, D = 1.50 m Mu = (quLx²/2) 95 72 kNm
Effective depth, d = t-75-ø/2 = 217 mm Ru = Mu/(øXf d²) 1.32 0.99
C. DIAGRAM ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0033 0.0025
ρmin = 0.002 0.0020 0.0020
As = ρbd 1228 1228 mm²
P Number of bar, N 8.8 8.8
Number of bar, N 6.1 6.1 pc(s)
M
SAY N 9.0 9.0 pc(s)

F. SHEAR
Ly

I. Wide Beam Shear

d ø Vc = 0.75(1/6 √ f'c )(b) (d) = 209.80 kN
Vu = qu x Shear Area = 180.81 kN Safe!
Yc
Yf

Xc Lx 0.4m
t

Xf
Xf
D. LOAD CONSIDERED
I. Service Load
Load, P = 390.8 kN
0.5m
II. Ultimate Load II. Punching Shear
Load, Pu = 552 kN ø Vc = 0.75(1/3 √ f'c )(b) (d) = 510.43 kN
Vu = qu x Shear Area = 500.86 kN Safe!
III. Additional Weight
Weight of Soil = 0 kN
Weight of Footing = 20 kN
0.62m

E. SOIL CAPACITY
qallowable = SBC = 150 kPa
qactual = P/A + 6M/bd² = 142.3 kPa Safe!

0.42m
SUMMARY
Therefore Provide 9-ø16 along X
Therefore Provide 9-ø16 along Y
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
FOOTING: F05 DATE: 17/10/2023
OWNER: GIANFRANCO L. FILART SHEET NO.: 5

ISOLATED FOOTING RECTANGULAR FOOTING

A. DESIGN INPUTS F. SOIL BEARING PRESSURE
Compressive Strength, f'c = 20.70 MPa
Yield Strength, fy = 414 MPa I. Along X
Unit Weight of Concrete = 23.54 kN/m³ qumax = 185.66 kPa
Unit Weight of Soil = 17.00 kN/m³ qumin = 185.66 kPa
øbar = 16 mm
Min. Spacing = 200 mm d II. Along Y
qumax = 185.66 kPa
qumin = 185.66 kPa
B. SIZING UP
I. Column
Length, Xc = 200 mm
Width, Yc = 400 mm
II. Footing
Ratio of Length and Width W = 1L qumin
Length, Xf = 1.80 m qumax
Width, Yf = 1.80 m G. DESIGN
Thickness, t = 325 mm Along X Along Y
Depth, D = 1.50 m Mu = (quLx²/2) 107 82 kNm
Effective depth, d = t-75-ø/2 = 242 mm Ru = Mu/(øXf d²) 1.13 0.86
C. DIAGRAM ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0028 0.0021
ρmin = 0.002 0.0020 0.0020
As = ρbd 1227 1227 mm²
P Number of bar, N 9.3 9.3
Number of bar, N 6.1 6.1 pc(s)
M
SAY N 10.0 10.0 pc(s)

F. SHEAR
Ly

I. Wide Beam Shear

d ø Vc = 0.75(1/6 √ f'c )(b) (d) = 247.73 kN
Vu = qu x Shear Area = 186.48 kN Safe!
Yc
Yf

Xc Lx 0.5m
t

Xf
Xf
D. LOAD CONSIDERED
I. Service Load
Load, P = 406.3 kN
0.6m
II. Ultimate Load II. Punching Shear
Load, Pu = 572 kN ø Vc = 0.75(1/3 √ f'c )(b) (d) = 596.76 kN
Vu = qu x Shear Area = 519.12 kN Safe!
III. Additional Weight
Weight of Soil = 0 kN
Weight of Footing = 25 kN
0.64m

E. SOIL CAPACITY
qallowable = SBC = 150 kPa
qactual = P/A + 6M/bd² = 133.0 kPa Safe!

0.44m
SUMMARY
Therefore Provide 10-ø16 along X
Therefore Provide 10-ø16 along Y
 Design

Figure 3: Finite element model

Page 1 of 8
6. Design summary
This section provides design information for beams, strips, and punching checks.

6.1. Preferences
Table 24: Design Preferences 01 - Resistance Factors
Table 24: Design Preferences 01 -
Resistance Factors
PhiTen PhiComp PhiShear

0.900000 0.650000 0.750000

Table 25: Design Preferences 02 - Rebar Cover - Slabs

Table 25: Design Preferences 02 - Rebar Cover - Slabs
CoverTop CoverBot BarSize InnerLayer PTCGSTop PTCGSBotE PTCGSBotI SlabType
xt nt
mm mm mm mm mm
15.000 15.000 18 B 25.000 40.000 25.000 Two Way

Table 26: Design Preferences 03 - Rebar Cover - Beams

Table 26: Design Preferences 03 - Rebar Cover - Beams
CoverTop CoverBot BarSizeF BarSizeS PTCGSTop PTCGSBot
mm mm mm mm
60.000 60.000 16 16 50.000 50.000

Table 27: Design Preferences 04 - Prestress Data

Table 27: Design Preferences 04 -
Prestress Data
UserStress InitConcRat LLFraction

No 0.800000 0.500000

6.2. Overwrites
Table 28: Slab Design Overwrites 02 - Finite Element Based, Part 1 of 2
Table 28: Slab Design Overwrites 02 - Finite Element
Based, Part 1 of 2
Area RebarMat

1 CSA-G30.18Gr400
2 CSA-G30.18Gr400
3 CSA-G30.18Gr400
4 CSA-G30.18Gr400

Page 2 of 8
Table 28: Slab Design Overwrites 02 - Finite Element
Based, Part 1 of 2
Area RebarMat

5 CSA-G30.18Gr400
6 CSA-G30.18Gr400
7 CSA-G30.18Gr400
8 CSA-G30.18Gr400
9 CSA-G30.18Gr400
11 CSA-G30.18Gr400
12 CSA-G30.18Gr400
14 CSA-G30.18Gr400
15 CSA-G30.18Gr400
16 CSA-G30.18Gr400
17 CSA-G30.18Gr400
18 CSA-G30.18Gr400
19 CSA-G30.18Gr400
20 CSA-G30.18Gr400
21 CSA-G30.18Gr400
22 CSA-G30.18Gr400
23 CSA-G30.18Gr400
24 CSA-G30.18Gr400
25 CSA-G30.18Gr400
26 CSA-G30.18Gr400
29 CSA-G30.18Gr400
30 CSA-G30.18Gr400
31 CSA-G30.18Gr400
32 CSA-G30.18Gr400
33 CSA-G30.18Gr400
34 CSA-G30.18Gr400
35 CSA-G30.18Gr400
36 CSA-G30.18Gr400
37 CSA-G30.18Gr400
38 CSA-G30.18Gr400
39 CSA-G30.18Gr400
40 CSA-G30.18Gr400
41 CSA-G30.18Gr400
42 CSA-G30.18Gr400
43 CSA-G30.18Gr400
44 CSA-G30.18Gr400

Table 28: Slab Design Overwrites 02 - Finite Element Based, Part 2 of 2

Table 28: Slab Design Overwrites 02 - Finite Element Based,
Part 2 of 2
Area RLLF Design IgnorePT

1 1.000000 Yes No
2 1.000000 Yes No
3 1.000000 Yes No
4 1.000000 Yes No
5 1.000000 Yes No
6 1.000000 Yes No
7 1.000000 Yes No
8 1.000000 Yes No
9 1.000000 Yes No
11 1.000000 Yes No

Page 3 of 8
Table 28: Slab Design Overwrites 02 - Finite Element Based,
Part 2 of 2
Area RLLF Design IgnorePT

12 1.000000 Yes No
14 1.000000 Yes No
15 1.000000 Yes No
16 1.000000 Yes No
17 1.000000 Yes No
18 1.000000 Yes No
19 1.000000 Yes No
20 1.000000 Yes No
21 1.000000 Yes No
22 1.000000 Yes No
23 1.000000 Yes No
24 1.000000 Yes No
25 1.000000 Yes No
26 1.000000 Yes No
29 1.000000 Yes No
30 1.000000 Yes No
31 1.000000 Yes No
32 1.000000 Yes No
33 1.000000 Yes No
34 1.000000 Yes No
35 1.000000 Yes No
36 1.000000 Yes No
37 1.000000 Yes No
38 1.000000 Yes No
39 1.000000 Yes No
40 1.000000 Yes No
41 1.000000 Yes No
42 1.000000 Yes No
43 1.000000 Yes No
44 1.000000 Yes No

Table 29: Beam Design Overwrites

Table 29: Beam Design Overwrites
Line CoverType RLLF IgnorePT

1 Section 1.000000 No
2 Section 1.000000 No
3 Section 1.000000 No
4 Section 1.000000 No
5 Section 1.000000 No
6 Section 1.000000 No
7 Section 1.000000 No
8 Section 1.000000 No
9 Section 1.000000 No
10 Section 1.000000 No
11 Section 1.000000 No
12 Section 1.000000 No
13 Section 1.000000 No
14 Section 1.000000 No
15 Section 1.000000 No
16 Section 1.000000 No

Page 4 of 8
 Table 29: Beam Design Overwrites
Line CoverType RLLF IgnorePT

17 Section 1.000000 No
18 Section 1.000000 No
19 Section 1.000000 No
20 Section 1.000000 No
21 Section 1.000000 No
22 Section 1.000000 No
23 Section 1.000000 No
24 Section 1.000000 No
25 Section 1.000000 No
26 Section 1.000000 No
27 Section 1.000000 No
28 Section 1.000000 No
29 Section 1.000000 No
30 Section 1.000000 No
31 Section 1.000000 No

Table 30: Punching Shear Design Overwrites 01 - General

Table 30: Punching Shear Design Overwrites 01 - General
Point Check LocType EffDepth ReinfType

14 Program Auto Auto None

Determined
16 Program Auto Auto None
Determined
18 Program Auto Auto None
Determined
20 Program Auto Auto None
Determined
22 Program Edge 2 Auto None
Determined
30 Program Auto Auto None
Determined
32 Program Auto Auto None
Determined
34 Program Auto Auto None
Determined
36 Program Auto Auto None
Determined
38 Program Edge 2 Auto None
Determined
48 Program Auto Auto None
Determined
50 Program Auto Auto None
Determined
52 Program Auto Auto None
Determined
54 Program Auto Auto None
Determined
57 Program Edge 2 Auto None
Determined
58 Program Auto Auto None
Determined
59 Program Auto Auto None
Determined

Page 5 of 8
 Table 30: Punching Shear Design Overwrites 01 - General
Point Check LocType EffDepth ReinfType

60 Program Auto Auto None

Determined
61 Program Auto Auto None
Determined
63 Program Edge 2 Auto None
Determined

Page 6 of 8
6.3. Slab design

Page 7 of 8
Page 8 of 8
 Design

1.9 m 2.3 m 2.3 m 1.9 m

1.5 m

1.5 m

1.5 m

1.5 m
Y

Figure 3: Finite element model

6. Design summary
This section provides design information for beams, strips, and punching checks.

6.1. Preferences
Table 24: Design Preferences 01 - Resistance Factors
Table 24: Design Preferences 01 -
Resistance Factors
PhiTen PhiComp PhiShear

0.900000 0.650000 0.750000

Table 25: Design Preferences 02 - Rebar Cover - Slabs

Table 25: Design Preferences 02 - Rebar Cover - Slabs
CoverTop CoverBot BarSize InnerLayer PTCGSTop PTCGSBotE PTCGSBotI SlabType
xt nt
mm mm mm mm mm
15.000 15.000 18 B 25.000 40.000 25.000 Two Way

Table 26: Design Preferences 03 - Rebar Cover - Beams

Table 26: Design Preferences 03 - Rebar Cover - Beams
CoverTop CoverBot BarSizeF BarSizeS PTCGSTop PTCGSBot
mm mm mm mm
50.000 75.000 16 10 50.000 50.000

Table 27: Design Preferences 04 - Prestress Data

Table 27: Design Preferences 04 -
Prestress Data
UserStress InitConcRat LLFraction

No 0.800000 0.500000

6.2. Overwrites
Table 28: Slab Design Overwrites 02 - Finite Element Based, Part 1 of 2
Table 28: Slab Design Overwrites 02 - Finite Element
Based, Part 1 of 2
Area RebarMat

1 CSA-G30.18Gr400
2 CSA-G30.18Gr400
3 CSA-G30.18Gr400
4 CSA-G30.18Gr400
Table 28: Slab Design Overwrites 02 - Finite Element
Based, Part 1 of 2
Area RebarMat

9 CSA-G30.18Gr400
10 CSA-G30.18Gr400
11 CSA-G30.18Gr400
12 CSA-G30.18Gr400
13 CSA-G30.18Gr400
14 CSA-G30.18Gr400
15 CSA-G30.18Gr400
16 CSA-G30.18Gr400
17 CSA-G30.18Gr400
18 CSA-G30.18Gr400
19 CSA-G30.18Gr400
20 CSA-G30.18Gr400

Table 28: Slab Design Overwrites 02 - Finite Element Based, Part 2 of 2

Table 28: Slab Design Overwrites 02 - Finite Element Based,
Part 2 of 2
Area RLLF Design IgnorePT

1 1.000000 Yes No
2 1.000000 Yes No
3 1.000000 Yes No
4 1.000000 Yes No
9 1.000000 Yes No
10 1.000000 Yes No
11 1.000000 Yes No
12 1.000000 Yes No
13 1.000000 Yes No
14 1.000000 Yes No
15 1.000000 Yes No
16 1.000000 Yes No
17 1.000000 Yes No
18 1.000000 Yes No
19 1.000000 Yes No
20 1.000000 Yes No

Table 29: Beam Design Overwrites

Table 29: Beam Design Overwrites
Line CoverType RLLF IgnorePT

1 Section 1.000000 No
2 Section 1.000000 No
3 Section 1.000000 No
4 Section 1.000000 No
5 Section 1.000000 No
6 Section 1.000000 No
7 Section 1.000000 No
8 Section 1.000000 No
9 Section 1.000000 No
10 Section 1.000000 No
Table 30: Punching Shear Design Overwrites 01 - General
Table 30: Punching Shear Design Overwrites 01 - General
Point Check LocType EffDepth ReinfType

1 Program Edge 3 Auto None

Determined
2 Program Auto Auto None
Determined
3 Program Edge 3 Auto None
Determined
4 Program Auto Auto None
Determined
5 Program Edge 3 Auto None
Determined
6 Program Auto Auto None
Determined
7 Program Edge 3 Auto None
Determined
8 Program Auto Auto None
Determined
6.3. Slab design
PROJECT: PROPOSED 2-STOREY RESIDENTIAL DESIGNER:
LOCATION: BLOCK 7, LOT 1, REMEDIOS ST. BRGY. DALIG, ANTIPOLO CITY DATE: 17/10/2023
OWNER GIANFRANCO L. FILART SHEET NO.: 1

SLAB DESIGN TABLE

A. CONCRETE PROPERTIES B. STEEL PROPERTIES C. CODE PROVISIONS D. DEAD LOADS E. LIVE LOADS
Concrete Unit Weight (λc) 23.54 kN/m³ Steel Yield, fy (ø12<) 276 Mpa Flexure Phi (ø) 0.90 1 4.00 kPa 6 1 1.90 kPa 6
Concrete Comp. Strength (f'c) 20.70 Mpa Steel Yield, fy (ø12>) 276 Mpa Min Spacing 200 mm 2 0.65 kPa 7 2 1.00 kPa 7
Young's Modulus (Ec) 21384 Mpa Young's Modulus (Es) 200000 Mpa ß1 0.90 3 8 3 8
Concrete, λc 1 Mpa 4 9 4 9
5 10 5 10

E.TWO WAY SLAB SUPPORT TYPES

Case 1 Case 2 Case 3 Case 4 Case 5 Case 6 Case 7 Case 8 Case 9

TABLE 1.0: SLAB DESIGN INPUTS TABLE 1.1: DESIGN MOMENT COEFFICIENT (TWO WAY) TABLE 1.2: DESIGN MOMENT FACTOR (ONE WAY)
Short Span Coefficient Long Span Coefficient Short Span factor
Short Span Long Span Left Support Right Support Eff depth, d Aspect Ratio,
SLAB ID Thk, t [mm] øbar Type Support Type Type Interior
[m] [m] Type Type [mm] m Ca- CaDL+ CaLL+ Cb- CbDL+ CbLL+ End Support Mid Span
Support
S01 3.25 3.25 125 10 1 Case 6 - - 100 1.00 2W 0.071 0.033 0.035 0.000 0.027 0.032 - - -
S02 1.9 4.1 125 10 1 Two End - - 100 0.46 1W - - - - - - 1/9 - 1/16
S03 0.5 3.5 125 10 2 Cantilever - - 100 0.14 1W - - - - - - 1/2 - -
S04 3.8 4.3 125 10 1 Case 6 - - 100 0.88 2W 0.080 0.040 0.043 0.000 0.020 0.024 - - -

TABLE 2.0: DESIGN LOADS TABLE 2.1: DESIGN MOMENTS

Service Ultimate Short Span Moment Long Span Moment Short Span Long Span Short Span Long Span
SLAB ID Dead Load Live Load Dead Load Live Load Wu [kPa] Ma- (END) MbLL+
Ma- [kNm] MaDL+ [kNm] MaLL+ [kNm] Mb- [kNm] MbDL+ [kNm] Ru- Ru- (END) Ru+ Ru- Ru+ ρ top ρ top (END) ρ bot ρ top ρ bot
[kPa] [kPa] [kPa] [kPa] [kNm] [kNm]
1 6.94 1.90 8.33 3.04 11.37 8.53 - 2.90 1.12 0.00 2.38 1.03 0.95 - 0.45 0.00 0.38 0.0035 - 0.0020 0.0020 0.0020
2 6.94 1.90 8.33 3.04 11.37 4.56 - 1.88 0.69 - - - 0.51 - 0.29 - - 0.0020 - 0.0020 - -
3 3.59 1.00 4.31 1.60 5.91 0.74 - - - - - - 0.08 - - - - 0.0020 - - - -
4 6.94 1.90 8.33 3.04 11.37 13.19 - 4.81 1.90 0.00 3.03 1.35 1.47 - 0.75 0.00 0.49 0.0055 - 0.0028 0.0020 0.0020

TABLE 3.0: REQUIRED STEEL AREA TABLE 3.1: REQUIRED SPACING OF REINFORCEMENT TABLE 4.0: DEFLECTION
Short Span [mm²] Long Span [mm²] Short Span [mm] Long Span [mm] ρ Provided Remarks/Warnings
Temp Bar δallow
Mark δ Criteria ξ δact [mm] One End Rebar
As top As top (END) As bot As top As bot S top S top (END) S bot S top S bot [mm] Short Span Long Span [mm] δ Summary
Warning Efficiency
1 353 - 250 250 250 200 - 200 200 200 200 L/240 2.00 0.0039 0.0039 0.93 13.54 OK! OK! OK! SLAB IS SAFE!
2 250 - 250 - - 200 - 200 - - 200 L/240 2.00 0.0039 - 0.42 7.92 OK! OK! OK! SLAB IS SAFE!
3 250 - - - - 200 - - - - 200 L/240 2.00 - - 0.02 2.08 OK! OK! OK! SLAB IS SAFE!
4 555 - 276 250 250 125 - 200 200 200 200 L/240 2.00 0.0039 0.0039 2.10 15.83 OK! OK! OK! SLAB IS SAFE!