Scribd
Upload
43 views3 pages

Pt100-Module Temp. HSCS

This document provides information about a surface temperature sensor for photovoltaic panels. It describes the sensor's features, specifications, installation process, and calibration. The sensor measures panel temperature and sends a voltage signal to monitoring devices to enhance energy production.

Uploaded by

Raj Ganesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views3 pages

Pt100-Module Temp. HSCS

This document provides information about a surface temperature sensor for photovoltaic panels. It describes the sensor's features, specifications, installation process, and calibration. The sensor measures panel temperature and sends a voltage signal to monitoring devices to enhance energy production.

Uploaded by

Raj Ganesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

HSCS100 – Surface Temperature Sensor

INTRODUCTION
The module temperature sensor is used by PV plant operators to know the temperature of
the modules installed in the array. The module temperature sensor converts this reading
into a voltage signal. This signal is sent back to the monitoring device.

As the system operator it’s important to know the systems’ performance. The module
temperature sensor will help to enhance kWh performance by ensuring reliable access to
the all-necessary data

Model: HSCS100 (Class A)


Features
• Fast, Stable and accurate
• IP65 enclosure Excellent long-term stability
• Onsite two-point calibration
• Loop powered

Specifications
• Measuring Range: 0 to 100 C
• Accuracy: 0.5 C
• Sensors: Temperature: RTD Pt100Ω
• Output: 4- 20 m amp
• Supply Voltage: 12 to 24 VDC
• Housing: Poly carbonate watertight enclosure
• Protection: IP-65
• Weight: Approx. 150gms

TOOLS AND MATERIALS NEEDED

Website: www.hscontrolsystems.com Email: [email protected]


INSTALLATION

This sensor is designed to attach directly to any solar panel. When placed on the center
back side of the panel, it accurately measures the temperature of the panel.

Prior to installation of the PV temperature sensor onto the PV panel, the installation area of
the panel back should be thoroughly cleaned. This cleaning will ensure a good bond
between sensor and panel and allow for accurate panel temperature readings.

After cleaning, peel off the protective adhesive tape on the temperature sensor and stick it
onto the back of the panel. Firmly press the sensor into place.

TOOLS AND MATERIALS NEEDED


Read this manual before beginning the installation to be sure you have everything you need.

• Wire cutters and stripper


• Multimeter
• Electrical Tapes to cover the wire
• Wire ties and tabs

LOCATION RECOMENDATION

Use the following guidelines to determine the best location for mounting the module surface
temperature Sensor. Select a PV module that remains unshaded throughout the day.

MOUNTING

Observe the following requirements regarding the mounting location of the module
temperature sensor:

• Select a PV module that remains unshaded throughout the day.


• Peel the backing from the adhesive tape and press the sensor firmly against the surface.
• Do not attempt to extend or shorten the pre-assembled 2.5 m cable.
• The module temperature sensor is affixed to the back of the PV module.
• Tie the sensor cable off in a way that does not pull on the sensor
• It is recommended to fix the sensor and the cable with an additional adhesive tape.

Website: www.hscontrolsystems.com Email: [email protected]


Example Installations:

CALIBRATION

• If using Modbus sensor then the PV Module Temperature Sensor is factory calibrated.

• If using analog output senor then use the following info to calibrate. Output - 4 to 20 m
amp (0- 100 deg C)

If the cable length is insufficient for the installation, additional cable can be added to the existing
cable. If this is done, an accuracy derating factor must be added to the overall temperature accuracy
of this sensor.

It is highly recommended that the calibration be checked annually

Under no circumstances should water or cleansing agents be used on the sensing elements. It is
recommended that the accuracy of the sensor is verified every 12 months.

Website: www.hscontrolsystems.com Email: [email protected]

You might also like