Scribd
Upload
11 views4 pages

Code Code

Uploaded by

nelson.inocente
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
11 views4 pages

Code Code

Uploaded by

nelson.inocente
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

#include <WiFi.

h>
#include <BlynkSimpleEsp32.h>

// WiFi credentials
char ssid[] = "YourWiFiSSID";
char pass[] = "YourWiFiPassword";

// Blynk authentication token


char auth[] = "YourAuthToken";

// Pins for motor control


#define MOTOR_A_PWM 2 // GPIO pin for PWM speed control of Motor A
#define MOTOR_A_FWD 4 // GPIO pin for forward direction of Motor A
#define MOTOR_A_REV 5 // GPIO pin for reverse direction of Motor A
#define MOTOR_B_PWM 14 // GPIO pin for PWM speed control of Motor B
#define MOTOR_B_FWD 15 // GPIO pin for forward direction of Motor B
#define MOTOR_B_REV 16 // GPIO pin for reverse direction of Motor B

// Pins for limit switches


#define LIMIT_SWITCH_A 18 // GPIO pin for limit switch A
#define LIMIT_SWITCH_B 19 // GPIO pin for limit switch B

// Blynk Virtual Pins


#define VIRTUAL_SPEED_PIN V0 // Virtual pin for speed control
#define VIRTUAL_FORWARD_PIN V1 // Virtual pin for forward direction
#define VIRTUAL_REVERSE_PIN V2 // Virtual pin for reverse direction
// Motor speed (0-255)
int motorSpeed = 0;
bool forwardRequested = false;
bool reverseRequested = false;

BLYNK_READ(VIRTUAL_SPEED_PIN) {
motorSpeed = param.asInt(); // Update motor speed when virtual pin V0 is read
}

BLYNK_READ(VIRTUAL_FORWARD_PIN) {
forwardRequested = param.asInt(); // Update forwardRequested when virtual pin V1 is read
}

BLYNK_READ(VIRTUAL_REVERSE_PIN) {
reverseRequested = param.asInt(); // Update reverseRequested when virtual pin V2 is read
}

void setup() {
// Setup Blynk
Blynk.begin(auth, ssid, pass);

// Setup GPIO pins for motor control


pinMode(MOTOR_A_PWM, OUTPUT);
pinMode(MOTOR_A_FWD, OUTPUT);
pinMode(MOTOR_A_REV, OUTPUT);
pinMode(MOTOR_B_PWM, OUTPUT);
pinMode(MOTOR_B_FWD, OUTPUT);
pinMode(MOTOR_B_REV, OUTPUT);

// Setup GPIO pins for limit switches


pinMode(LIMIT_SWITCH_A, INPUT_PULLUP);
pinMode(LIMIT_SWITCH_B, INPUT_PULLUP);
}

void loop() {
Blynk.run();

// Example logic for gate movement based on forward/reverse requests and limit switch status
if (forwardRequested && digitalRead(LIMIT_SWITCH_A)) {
// Move gate in forward direction
analogWrite(MOTOR_A_PWM, motorSpeed);
digitalWrite(MOTOR_A_FWD, HIGH);
digitalWrite(MOTOR_A_REV, LOW);
analogWrite(MOTOR_B_PWM, motorSpeed);
digitalWrite(MOTOR_B_FWD, HIGH);
digitalWrite(MOTOR_B_REV, LOW);
} else if (reverseRequested && digitalRead(LIMIT_SWITCH_B)) {
// Move gate in reverse direction
analogWrite(MOTOR_A_PWM, motorSpeed);
digitalWrite(MOTOR_A_FWD, LOW);
digitalWrite(MOTOR_A_REV, HIGH);
analogWrite(MOTOR_B_PWM, motorSpeed);
digitalWrite(MOTOR_B_FWD, LOW);
digitalWrite(MOTOR_B_REV, HIGH);
} else {
// Stop gate movement
analogWrite(MOTOR_A_PWM, 0);
analogWrite(MOTOR_B_PWM, 0);
}
}

You might also like