B550M C

Version 1.
0
Published September 2021
Copyright©2021 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com

AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage caused by our
goods. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure. If
you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard
International call charges apply)
The terms HDMI® and HDMI High-Definition Multimedia Interface, and the
HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
CE Warning
This device complies with directive 2014/53/EU issued by the Commision of the European
Community.
This equipment complies with EU radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Operations in the 5.15-5.35GHz band are restricted to indoor usage only.
Radio transmit power per transceiver type
Function Frequency Maximum Output Power (EIRP)

2400-2483.5 MHz 18.5 + / -1.5 dbm
5150-5250 MHz 21.5 + / -1.5 dbm
18.5 + / -1.5 dbm (no TPC)
WiFi 5250-5350 MHz
21.5 + / -1.5 dbm (TPC)
25.5 + / -1.5 dbm (no TPC)
5470-5725 MHz
28.5 + / -1.5 dbm (TPC)
Bluetooth 2400-2483.5 MHz 8.5 + / -1.5 dbm
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specifications 2
1.3 Motherboard Layout 7
1.4 I/O Panel 9
1.5 WiFi-802.11ac Module and ASRock WiFi 2.4/5 GHz

Antennas 10
Chapter 2 Installation 12
2.1 Installing the CPU 13
2.2 Installing the CPU Fan and Heatsink 15
2.3 Installing Memory Modules (DIMM) 23
2.4 Expansion Slots (PCI Express Slots) 27
2.5 Jumpers Setup 29
2.6 Onboard Headers and Connectors 30
2.7 Post Status Checker 35
2.8 CrossFireX TM and Quad CrossFireX TM Operation Guide 36
2.8.1 Installing Two CrossFireX TM-Ready Graphics Cards 36
2.8.2 Driver Installation and Setup 38
2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1) 39
2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2) 42
Chapter 3 Software and Utilities Operation 45

3.1 Installing Drivers 45
3.2 ASRock Motherboard Utility (A-Tuning) 46
3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 46
3.2.2 Using ASRock Motherboard Utility (A-Tuning) 46
3.3 ASRock Live Update & APP Shop 49
3.3.1 UI Overview 49
3.3.2 Apps 50
3.3.3 BIOS & Drivers 53
3.3.4 Setting 54
3.4 ASRock Polychrome SYNC 55
Chapter 4 UEFI SETUP UTILITY 58

4.1 Introduction 58
4.1.1 UEFI Menu Bar 58
4.1.2 Navigation Keys 59
4.2 Main Screen 60
4.3 OC Tweaker Screen 61
4.4 Advanced Screen 65
4.4.1 CPU Configuration 66
4.4.2 Onboard Devices Configuration 67
4.4.3 Storage Configuration 69
4.4.4 ACPI Configuration 70
4.4.5 Trusted Computing 71
4.4.6 AMD CBS 72
4.4.7 AMD PBS 73
4.4.8 AMD Overclocking 74

4.5 Tools 75
4.6 Hardware Health Event Monitoring Screen 76
4.7 Security Screen 78
4.8 Boot Screen 79
4.9 Exit Screen 82

B550M-C
Chapter 1 Introduction
Thank you for purchasing ASRock B550M-C motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality
and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the software and utilities. Chapter 4 contains the configuration guide of
the BIOS setup.
Because the motherboard specifications and the BIOS software might be updated, the
content of this documentation will be subject to change without notice. In case any
modifications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, please visit our website for specific information about the model
you are using. You may find the latest VGA cards and CPU support list on ASRock’s
website as well. ASRock website http://www.asrock.com.
1.1 Package Contents

• ASRock B550M-C Motherboard (Micro ATX Form Factor)
• 1 x I/O Panel Shield
• 2 x Serial ATA (SATA) Data Cables (Optional)
• 2 x ASRock WiFi 2.4/5 GHz Antennas (Optional)
• 2 x Screws for M.2 Sockets (Optional)
English
1
1.2 Specifications
Platform • Micro ATX Form Factor

• Solid Capacitor design
• 2oz Copper PCB
CPU • Supports AMD AM4 Socket Ryzen™ 3000, 3000 G-Series,

4000 G-Series, 5000 and 5000 G-Series Desktop Processors*
* Not compatible with AMD Athlon™ Processors.
• Digi Power design
• 8 Power Phase design
Chipset • AMD B550
Memory • Dual Channel DDR4 Memory Technology

• 4 x DDR4 DIMM Slots
• AMD Ryzen series CPUs (Vermeer) support DDR4
4533+(OC)/4466(OC)/4400(OC)/4333(OC)/4266(OC)/
4200(OC)/4133(OC)/4000(OC)/3866(OC)/3800(OC)/3733
(OC)/3600(OC)/3466(OC)/3200/2933/2667/2400/2133 ECC
& non-ECC, un-buffered memory*
• AMD Ryzen series CPUs (Matisse) support DDR4
4533+(OC)/4466(OC)/4400(OC)/4333(OC)/4266(OC)/
4200(OC)/4133(OC)/4000(OC)/3866(OC)/3800(OC)/3733
(OC)/3600(OC)/3466(OC)/3200/2933/2667/2400/2133 ECC
& non-ECC, un-buffered memory*
• AMD Ryzen series APUs (Cezanne) support DDR4
4733+(OC)/4666(OC)/4600(OC)/4533(OC)/4466(OC)/
4400(OC)/4333(OC)/4266(OC)/4200(OC)/4133(OC)/
4000(OC)/3866(OC)/3800(OC)/3733(OC)/3600(OC)/
3466(OC)/3200/2933/2667/2400/2133 ECC & non-ECC, un-
buffered memory*
• AMD Ryzen series APUs (Renoir) support DDR4 4733+(OC
)/4666(OC)/4600(OC)/4533(OC)/4466(OC)/4400(OC)
/4333(OC)/4266(OC)/4200(OC)/4133(OC)/4000(OC)/
3866(OC)/3800(OC)/3733(OC)/3600(OC)/3466(OC)/
English
3200/2933/2667/2400/2133 ECC & non-ECC, un-buffered

memory*
2
B550M-C
• AMD Ryzen series APUs (Picasso) support DDR4

3333+(OC)/3200(OC)/2933/2667/2400/2133 non-ECC, un-
buffered memory*
* For Ryzen Series APUs (Picasso, Cezanne and Renoir), ECC
is only supported with PRO CPUs.
* Please refer to Memory Support List on ASRock’s website for
more information. (http://www.asrock.com/)
* Please refer to page 23 for AMD non-XMP memory frequency
support. For more details, please refer to the QVL on ASRock's
website.
• Max. capacity of system memory: 128GB
• Supports Extreme Memory Profile (XMP) memory modules
• 15μ Gold Contact in DIMM Slots
Expansion AMD Ryzen series CPUs (Vermeer and Matisse)

Slot • 2 x PCI Express x16 Slots (PCIE1: Gen4x16 mode; PCIE4:
Gen3 x4 mode)*
AMD Ryzen series APUs (Cezanne and Renoir)
• 2 x PCI Express x16 Slots (PCIE1: Gen3x16 mode; PCIE4:
Gen3 x4 mode)*
AMD Ryzen series APUs (Picasso)
• 2 x PCI Express x16 Slots (PCIE1: Gen3x8 mode; PCIE4:
Gen3 x4 mode)*
* Supports NVMe SSD as boot disks

• 2 x PCI Express 3.0 x16 Slots (PCIE2/PCIE3: x1 mode)
TM TM
• Supports AMD Quad CrossFireX and CrossFireX
• 1 x Vertical M.2 Socket (Key E) with the bundled WiFi-
802.11ac module (on the rear I/O)
TM
Graphics • Integrated AMD Radeon Vega Series Graphics in Ryzen
Series APU*
* Actual support may vary by CPU
• DirectX 12, Pixel Shader 5.0
• Shared memory default 2GB. Max Shared memory supports
up to 16GB.
English
* The Max shared memory 16GB requires 32GB system

memory installed.
• Supports HDMI 2.1 with max. resolution up to 4K x 2K
(4096x2160) @ 60Hz
3
• Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
HBR (High Bit Rate Audio) with HDMI 2.1 Port (Compliant
HDMI monitor is required)
• Supports HDR (High Dynamic Range) with HDMI 2.1
• Supports HDCP 2.3 with HDMI 2.1 Port
* Picasso supports HDCP 2.2 with HDMI 2.0 Port
• Supports 4K Ultra HD (UHD) playback with HDMI 2.1
Port
• Supports Microsoft PlayReady®
Audio • 7.1 CH HD Audio (Realtek ALC897 Audio Codec)

• Supports Surge Protection
LAN • PCIE x1 Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111H
• Supports Wake-On-LAN
• Supports Lightning/ESD Protection
• Supports Energy Efficient Ethernet 802.3az
• Supports PXE
Wireless • Intel® 802.11ac WiFi Module

LAN • Supports IEEE 802.11a/b/g/n/ac
• Supports Dual-Band (2.4/5 GHz)
• Supports high speed wireless connections up to 433Mbps
• Supports Bluetooth 4.2+ High speed class II
Rear Panel • 2 x Antenna Ports

I/O • 1 x PS/2 Mouse/Keyboard Port
• 1 x HDMI Port
• 1 x USB 3.2 Gen2 Type-A Port (10 Gb/s) (Supports ESD
Protection)
• 1 x USB 3.2 Gen2 Type-C Port (10 Gb/s) (Supports ESD
Protection)
• 4 x USB 3.2 Gen1 Ports (ASMedia ASM1074 hub) (Supports
ESD Protection)
English
• 2 x USB 2.0 Ports (Supports ESD Protection)

• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
4
B550M-C
Storage • 6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1 and RAID 10), NCQ, AHCI and Hot Plug*
* M2_2 and SATA3_5_6 share lanes. If either one of them is in
use, the other one will be disabled.
• 1 x Hyper M.2 Socket (M2_1), supports M Key type 2280
M.2 PCI Express module up to Gen4x4 (64 Gb/s) (with Ver-
meer, Matisse) or Gen3x4 (32 Gb/s) (with Cezanne, Renoir
and Picasso)**
• 1 x M.2 Socket (M2_2), supports M Key type 2280 M.2
SATA3 6.0 Gb/s module and M.2 PCI Express module up to
Gen3 x2 (16 Gb/s)**
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit
Connector • 1 x SPI TPM Header

• 1 x Power LED and Speaker Header
• 2 x RGB LED Headers
* Support in total up to 12V/3A, 36W LED Strip
• 2 x Addressable LED Headers
* Support in total up to 5V/3A, 15W LED Strip
• 1 x CPU Fan Connector (4-pin)
* The CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.
• 3 x Chassis/Water Pump Fan Connectors (4-pin) (Smart
Fan Speed Control)
* The Chassis/Water Pump Fan supports the water cooler fan
of maximum 2A (24W) fan power.
* CHA_FAN1/WP, CHA_FAN2/WP and CHA_FAN3/WP can
auto detect if 3-pin or 4-pin fan is in use.
• 1 x 24 pin ATX Power Connector
• 1 x 8 pin 12V Power Connector
• 1 x Front Panel Audio Connector
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
ESD Protection)
• 2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)
(Supports ESD Protection)
English
5
BIOS • AMI UEFI Legal BIOS with GUI support
Feature • Supports “Plug and Play”
• ACPI 5.1 compliance wake up events
• Supports jumperfree
• SMBIOS 2.3 support
• CPU, CPU VDDCR_SOC, DRAM, +1.8VSB Voltage Multi-
adjustment
Hardware • Temperature Sensing: CPU, Chassis/Water Pump Fans

Monitor • Fan Tachometer: CPU, Chassis/Water Pump Fans
• Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
ture): CPU, Chassis/Water Pump Fans
• Fan Multi-Speed Control: CPU, Chassis/Water Pump Fans
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, CPU
VDDCR_SOC, DRAM, VPPM, +1.8V
OS • Microsoft® Windows® 10 64-bit / 11 64-bit
Certifica- • FCC, CE
tions • ErP/EuP ready (ErP/EuP ready power supply is required)
• CEC Tier II ready
* For detailed product information, please visit our website: http://www.asrock.com
Please realize that there is a certain risk involved with overclocking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using
third-party overclocking tools. Overclocking may affect your system’s stability, or
even cause damage to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for possible damage caused by
overclocking.
English
6
B550M-C
1.3 Motherboard Layout
English
7
No. Description
1 8 pin 12V Power Connector (ATX12V1)
2 CPU Fan Connector (CPU_FAN1)
3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
5 RGB LED Header (RGB_LED1)
6 Addressable LED Header (ADDR_LED1)
7 ATX Power Connector (ATXPWR1)
8 USB 3.2 Gen1 Header (F_USB3_1_2)
9 SATA3 Connector (SATA3_2)
10 SATA3 Connector (SATA3_1)
11 SATA3 Connector (SATA3_4) (Upper), SATA3 Connector (SATA3_3) (Lower)
12 SATA3 Connector (SATA3_6) (Upper), SATA3 Connector (SATA3_5) (Lower)
13 System Panel Header (PANEL1)
14 Power LED and Speaker Header (SPK_PLED1)
15 USB 3.2 Gen1 Header (F_USB3_3_4)
16 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)
17 Post Status Checker (PSC)
18 SPI TPM Header (SPI_TPM_J1)
19 USB 2.0 Header (USB_3_4)
20 USB 2.0 Header (USB_5_6)
21 Clear CMOS Jumper (CLRCMOS1)
24 Addressable LED Header (ADDR_LED2)
25 RGB LED Header (RGB_LED2)
26 Front Panel Audio Header (HD_AUDIO1)
English
8
B550M-C
1.4 I/O Panel

3
1 2 4
12 11 10 9 8 6 5
7
No. Description No. Description

1 USB 2.0 Ports (USB12) 7 USB 3.2 Gen2 Type-C Port
2 LAN RJ-45 Port* (USB31_TC_1)
3 Line In (Light Blue)** 8 Antenna Ports
4 Front Speaker (Lime)** 9 USB 3.2 Gen1 Ports (USB3_34)
5 Microphone (Pink)** 10 USB 3.2 Gen1 Ports (USB3_12)
6 USB 3.2 Gen2 Type-A Port 11 PS/2 Mouse/Keyboard Port
(USB31_TA_1) 12 HDMI Port
* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Port
Activity / Link LED Speed LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
** Function of the Audio Ports in 7.1-channel Configuration:

English
Port Function
Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out
9
1.5 WiFi-802.11ac Module and ASRock WiFi 2.4/5 GHz
Antennas
WiFi-802.11ac + BT Module
This motherboard comes with an exclusive WiFi 802.11 a/b/g/n/ac + BT v4.2
module (pre-installed on the rear I/O panel) that offers support for WiFi 802.11 a/b/
g/n/ac connectivity standards and Bluetooth v4.2. WiFi + BT module is an easy-to-
use wireless local area network (WLAN) adapter to support WiFi + BT. Bluetooth
v4.2 standard features Smart Ready technology that adds a whole new class of
functionality into the mobile devices. BT 4.2 also includes Low Energy Technology
and ensures extraordinary low power consumption for PCs.
* The transmission speed may vary according to the environment.

English
10
B550M-C
WiFi Antennas Installation Guide
Step 1
Prepare the WiFi 2.4/5 GHz Antennas that come
with the package.
Step 2
Connect the two WiFi 2.4/5 GHz Antennas to
the antenna connectors. Turn the antenna clock-
wise until it is securely connected.
Step 3
Set the WiFi 2.4/5 GHz Antenna as shown in the

illustration.
*You may need to adjust the direction of
the antenna for a stronger signal. English
11
Chapter 2 Installation
This is a Micro ATX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Make sure to unplug the power cord before installing or removing the motherboard.
Failure to do so may cause physical injuries to you and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not over-
tighten the screws! Doing so may damage the motherboard.
English
12
B550M-C
2.1 Installing the CPU
Unplug all power cables before installing the CPU.
English
13
3
14
English
B550M-C
2.2 Installing the CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a larger
heatsink and cooling fan to dissipate heat. You also need to spray thermal grease
between the CPU and the heatsink to improve heat dissipation. Make sure that the
CPU and the heatsink are securely fastened and in good contact with each other.
Please turn off the power or remove the power cord before changing a CPU or heatsink.
Installing the CPU Box Cooler SR1
2
English
15
English
16
4
3
CP
U_
FA
N1
B550M-C
Installing the AM4 Box Cooler SR2
English
17
3
18
English
B550M-C
1N
FA
U_
CP
*The diagrams shown here are for reference only. The headers might be in a different
position on your motherboard.
English
19
Installing the AM4 Box Cooler SR3
2
English
20
B550M-C
English
21
5
N1
FA
U_
CP
6
1N
FA
U_
CP
2
ED
B _L
+12V RG
*The diagrams shown here are for reference only. The headers might be in a different
English
position on your motherboard.
22
B550M-C
2.3 Installing Memory Modules (DIMM)

This motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.
1. For dual channel configuration, you always need to install identical (the same
brand, speed, size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one or three
memory module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4
slot; otherwise, this motherboard and DIMM may be damaged.
4. We suggest that you install the memory modules on DDR4_A2 and DDR4_B2 first
for better DRAM compatibility on 2 DIMMs configuration.
AMD non-XMP Memory Frequency Support

Ryzen Series CPUs (Vermeer):
UDIMM Memory Slot Frequency

A1 A2 B1 B2 (Mhz)
- SR - - 3200
- DR - - 3200
- SR - SR 3200
- DR - DR 3200
SR SR SR SR 2933
SR/DR DR SR/DR DR 2667
SR/DR SR/DR SR/DR SR/DR 2667
Ryzen Series CPUs (Matisse):

A1 A2 B1 B2 (Mhz)
- SR - - 3200
- DR - - 3200
English
- SR - SR 3200
- DR - DR 3200
SR SR SR SR 2933

23
Ryzen Series APUs (Cezanne):

A1 A2 B1 B2 (Mhz)
- SR - - 3200
- DR - - 3200
- SR - SR 3200
- DR - DR 3200
SR SR SR SR 2933
Ryzen Series APUs (Renoir):

A1 A2 B1 B2 (Mhz)
- SR - - 3200
- DR - - 3200
- SR - SR 3200
- DR - DR 3200
SR SR SR SR 2933

English
24
B550M-C
Ryzen Series APUs (Picasso):

A1 A2 B1 B2 (Mhz)
- SR - - 2933
- DR - - 2667
- SR - SR 2667
- DR - DR 2400
SR SR SR SR 2133
SR: Single rank DIMM, 1Rx4 or 1Rx8 on DIMM module label

DR: Dual rank DIMM, 2Rx4 or 2Rx8 on DIMM module label
English
25
The DIMM only fits in one correct orientation. It will cause permanent damage to
the motherboard and the DIMM if you force the DIMM into the slot at incorrect
orientation.
3
English
26
B550M-C
2.4 Expansion Slots (PCI Express Slots)

There are 4 PCI Express slots on the motherboard.
Before installing an expansion card, please make sure that the power supply is
switched off or the power cord is unplugged. Please read the documentation of the
expansion card and make necessary hardware settings for the card before you start
the installation.
PCIe slots:
PCIE1 (PCIe 4.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x1 lane width cards.
PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIe Slot Configurations

Ryzen series CPUs (Vermeer and Matisse):
PCIE1 PCIE4
Single Graphics Card Gen4x16 N/A
Two Graphics Cards in

Gen4x16 Gen3x4
CrossFireXTM Mode
Ryzen series APUs (Cezanne and Renoir):

PCIE1 PCIE4

Gen3x16 Gen3x4
CrossFireXTM Mode
English
27
Ryzen series APUs (Picasso):
PCIE1 PCIE4

Gen3x8 Gen3x4
CrossFireXTM Mode
For a better thermal environment, please connect a chassis fan to the motherboard’s
chassis fan connector (CHA_FAN1/WP, CHA_FAN2/WP or CHA_FAN3/WP )
when using multiple graphics cards.
English
28
B550M-C
2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is
“Open”.
Clear CMOS Jumper Short: Clear CMOS

(see p.7, No. 21) 2-pin Jumper Open: Default
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn off the computer and unplug the power
cord from the power supply. After waiting for 15 seconds, use a jumper cap to
short the pins on CLRCMOS1 for 5 seconds. However, please do not clear the
CMOS right after you update the BIOS. If you need to clear the CMOS when you
just finish updating the BIOS, you must boot up the system first, and then shut it
down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default profile will be cleared only if the CMOS battery is
removed. Please remember to remove the jumper cap after clearing the CMOS.
English
29
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.
System Panel Header PLED+

PLED-
Connect the power
(9-pin PANEL1) PWRBTN#
GND button, reset button and
(see p.7, No. 13) system status indicator on
1
GND the chassis to this header
RESET#
GND according to the pin
HDLED-
HDLED+ assignments below. Note
the positive and negative
pins before connecting
the cables.
PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may configure the way to
turn off your system using the power switch.
RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart
the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when
the system is operating. The LED keeps blinking when the system is in S3 sleep state.
The LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when
the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists
of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make sure the wire
assignments and the pin assignments are matched correctly.
English
30
B550M-C
Power LED and Speaker SPEAKER Please connect the

DUMMY
Header DUMMY chassis power LED and
+5V
(7-pin SPK_PLED1) the chassis speaker to this
(see p.7, No. 14) 1
header.
PLED+
PLED+
PLED-
Serial ATA3 Connectors These six SATA3

SATA3_1
SATA3_2
Right Angle: connectors support SATA
(SATA3_4: data cables for internal
see p.7, No. 11) (Upper) storage devices with up to
(SATA3_3: 6.0 Gb/s data transfer rate.
SATA3_6 SATA3_4
SATA3_5 SATA3_3
see p.7, No. 11) (Lower) * M2_2 and SATA3_5_6

(SATA3_6: share lanes. If either one
see p.7, No. 12) (Upper) of them is in use, the other
(SATA3_5: one will be disabled.
see p.7, No. 12) (Lower)
Vertical:
(SATA3_1:
see p.7, No. 10)
(SATA3_2:
see p.7, No. 9)
USB 2.0 Headers USB_PWR

There are two headers
P-
(9-pin USB_3_4) P+
GND
on this motherboard.
DUMMY
(see p.7, No. 19) Each USB 2.0 header can
(9-pin USB_5_6) 1 support two ports.
GND
(see p.7, No. 20) P+
P-
USB_PWR
USB 3.2 Gen1 Headers Vbus There are two headers on

Vbus IntA_PB_SSRX-
(19-pin F_USB3_1_2) IntA_PA_SSRX- IntA_PB_SSRX+ this motherboard. Each

IntA_PA_SSRX+ GND
(see p.7, No. 8) GND IntA_PB_SSTX- USB 3.2 Gen1 header can
IntA_PA_SSTX- IntA_PB_SSTX+
IntA_PA_SSTX+ GND support two ports.
English
GND IntA_PB_D-
IntA_PA_D- IntA_PB_D+
IntA_PA_D+ Dummy
1
31
IntA_P_D+
(19-pin F_USB3_3_4) IntA_P_D-
GND
IntA_P_SSTX+
(see p.7, No. 15) IntA_P_SSTX-
GND
IntA_P_SSRX+
IntA_P_SSRX-
Vbus
1
Vbus
IntA_P_SSRX-
IntA_P_SSRX+
GND
IntA_P_SSTX-
IntA_P_SSTX+
GND
IntA_P_D-
IntA_P_D+
ID
Front Panel Audio Header GND This header is for

PRESENCE#
(9-pin HD_AUDIO1) MIC_RET
OUT_RET
connecting audio devices
(see p.7, No. 26) to the front audio panel.
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must
support HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.
Chassis Water Pump Fan GND This motherboard

FAN_VOLTAGE
Connectors CHA_FAN_SPEED
provides three 4-Pin water
(4-pin CHA_FAN1/WP) FAN_SPEED_CONTROL cooling chassis fan
(see p.7, No. 22) connectors. If you plan to
(4-pin CHA_FAN2/WP) 1 2 3 4 connect a 3-Pin chassis
English
(see p.7, No. 23) water cooler fan, please

(4-pin CHA_FAN3/WP) connect it to Pin 1-3.
(see p.7, No. 16)
32
B550M-C
CPU Fan Connector 4 3 2 1 This motherboard pro-

(4-pin CPU_FAN1) vides a 4-Pin CPU fan
GND
(see p.7, No. 2) +12V
CPU_FAN_SPEED
(Quiet Fan) connector.
If you plan to connect a
FAN_SPEED_CONTROL
3-Pin CPU fan, please

connect it to Pin 1-3.
ATX Power Connector 12 24 This motherboard pro-

(24-pin ATXPWR1) vides a 24-pin ATX power
(see p.7, No. 7) connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
1 13
13.
ATX 12V Power 8 5 This motherboard

Connector provides an 8-pin ATX
(8-pin ATX12V1) 4 1 12V power connector. To
(see p.7, No. 1) use a 4-pin ATX power
supply, please plug it along
Pin 1 and Pin 5.
*Warning: Please make
sure that the power cable
connected is for the CPU
and not the graphics
card. Do not plug the
PCIe power cable to this
connector.
SPI TPM Header SPI_DQ3 This connector supports SPI

SPI_PWR
(13-pin SPI_TPM_J1) Dummy
CLK
Trusted Platform Module (TPM)
SPI_MOSI
(see p.7, No. 18) RST#
TPM_PIRQ
system, which can securely store
keys, digital certificates, pass-
1
SPI_TPM_CS#
words, and data. A TPM system
GND
RSMRST# also helps enhance network
SPI_MISO
SPI_CS0 security, protects digital
English
SPI_DQ2
identities, and ensures platform

integrity.
33
RGB LED Headers These two RGB headers are used
(4-pin RGB_LED1) to connect RGB LED extension
(see p.7, No. 5) cable which allows
users to choose from various LED
lighting effects.
Caution: Never install the RGB
LED cable in the wrong orienta-
(4-pin RGB_LED2) 1 tion; otherwise, the cable may
12V G R B
(see p.7, No. 25) be damaged.
*Please refer to page 55 for
further instructions on these two
headers.
Addressable LED Headers These two Addressable headers

(3-pin ADDR_LED1) are used to connect Addressable
(see p.7, No. 6) LED extension cable which
allows users to choose from
various LED lighting effects.
Caution: Never install the
(3-pin ADDR_LED2) 1
Addressable LED cable in the
(see p.7, No. 24) GND wrong orientation; otherwise,
DO_ADDR
VOUT
the cable may be damaged.
*Please refer to page 56 for
further instructions on this
header.
English
34
B550M-C
2.7 Post Status Checker

Post Status Checker (PSC) diagnoses the computer when users power on the
machine. It emits a red light to indicate whether the CPU, memory, VGA or stor-
age is dysfunctional. The lights go off if the four mentioned above are functioning
normally.
English
35
2.8 CrossFireXTM and Quad CrossFireXTM Operation Guide
This motherboard supports CrossFireXTM and Quad CrossFireXTM that allows you
to install up to two identical PCI Express x16 graphics cards.
1. You should only use identical CrossFireXTM-ready graphics cards that are AMD
certified.
2. Make sure that your graphics card driver supports AMD CrossFireXTM technology.
Download the drivers from the AMD’s website: www.amd.com
3. Make sure that your power supply unit (PSU) can provide at least the minimum
power your system requires. It is recommended to use a AMD certified PSU. Please
refer to the AMD’s website for details.
4. If you pair a 12-pipe CrossFireXTM Edition card with a 16-pipe card, both cards will
operate as 12-pipe cards while in CrossFireXTM mode.
5. Different CrossFireXTM cards may require different methods to enable CrossFi-
reXTM. Please refer to AMD graphics card manuals for detailed installation guide.
2.8.1 Installing Two CrossFireXTM-Ready Graphics Cards
Step 1
Insert one graphics card into PCIE1 slot
and the other graphics card to PCIE4 slot.
Make sure that the cards are properly
seated on the slots.
Step 2
Connect two graphics cards by installing
a CrossFire Bridge on the CrossFire Bridge
CrossFire Bridge Interconnects on the top of the graphics
cards. (The CrossFire Bridge is provided
with the graphics card you purchase, not
bundled with this motherboard. Please
refer to your graphics card vendor for
English
details.)
36
B550M-C
Step 3
Connect a VGA/DVI/DP/HDMI cable
from the monitor to the corresponding
port on the graphics card installed to the
PCIE1 slot.
English
37
2.8.2 Driver Installation and Setup
Step 1
Power on your computer and boot into OS.
Step 2
Remove the AMD drivers if you have any VGA drivers installed in your system.
The Catalyst Uninstaller is an optional download. We recommend using this utility

to uninstall any previously installed Catalyst drivers prior to installation. Please
check AMD’s website for AMD driver updates.
Step 3
Install the required drivers and CATALYST Control Center then restart your
computer. Please check AMD’s website for details.
Step 4
Double-click the AMD Catalyst Control
AMD Catalyst Control Center Center icon in the Windows® system tray.
Step 5
In the left pane, click Performance and
then AMD CrossFireXTM . Then select
Enable AMD CrossFireX and click Apply.
Select the GPU number according to your
graphics card and click Apply.
English
38
B550M-C
2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1)

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA.
The Hyper M.2 Socket (M2_1) supports M Key type 2280 M.2 PCI Express module up to
Gen4x4 (64 Gb/s) (with Vermeer, Matisse) or Gen3x4 (32 Gb/s) (with Cezanne, Renoir and
Picasso).
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module

and the screw.
Step 2
Depending on the PCB type and

length of your M.2_SSD (NGFF)
module, find the corresponding nut
location to be used.
No. 1
Nut Location A
PCB Length 8cm
Module Type Type2280
English
39
Step 3
Align and gently insert the M.2

(NGFF) SSD module into the M.2
slot. Please be aware that the M.2
(NGFF) SSD module only fits in one
orientation.
A
A 20o
Step 4
Tighten the screw with a screwdriver

to secure the module into place.
Please do not overtighten the screw
as this might damage the module.
NUT2 NUT1
English
40
B550M-C
M.2_SSD (NGFF) Module Support List (M2_1)
Vendor Interface P/N

ADATA PCIe3 x4 ASX7000NP-128GT-C
ADATA PCIe3 x4 ASX8000NP-256GM-C
ADATA PCIe3 x4 ASX8000NP-512GM-C
Apacer PCIe3 x4 AP240GZ280
Corsair PCIe3 x4 CSSD-F240GBMP500
Intel PCIe3 x4 SSDPEKKF256G7
Intel PCIe3 x4 SSDPEKKF512G7
Kingston PCIe3 x4 SKC1000/480G
Kingston PCIe2 x4 SH2280S3/480G
OCZ PCIe3 x4 RVD400 -M2280-512G (NVME)
PATRIOT PCIe3 x4 PH240GPM280SSDR NVME
Plextor PCIe3 x4 PX-128M8PeG
Plextor PCIe3 x4 PX-1TM8PeG
Plextor PCIe PX-G256M6e
Samsung PCIe3 x4 SM961 MZVPW128HEGM (NVM)
Samsung PCIe3 x4 PM961 MZVLW128HEGR (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250) (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250BW) (NVME)
Samsung PCIe3 x4 SM951 (NVME)
Samsung PCIe3 x4 SM951 (MZHPV256HDGL)
Samsung PCIe3 x4 SM951 (MZHPV512HDGL)
Samsung PCIe3 x4 SM951 (NVME)
Samsung PCIe x4 XP941-512G (MZHPU512HCGL)
SanDisk PCIe SD6PP4M-128G
TEAM PCIe3 x4 TM8FP2240G0C101
TEAM PCIe3 x4 TM8FP2480GC110
WD PCIe3 x4 WDS256G1X0C-00ENX0 (NVME)
WD PCIe3 x4 WDS512G1X0C-00ENX0 (NVME)
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com
English
41
2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. The M.2 Socket
(M2_2) supports M Key type 2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express
module up to Gen3 x2 (16 Gb/s).
* M2_2 and SATA3_5_6 share lanes. If either one of them is in use, the other one will be
disabled.
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module

and the screw.
Step 2
Depending on the PCB type and

length of your M.2_SSD (NGFF)
module, find the corresponding nut
location to be used.
No. 1
Nut Location A
PCB Length 8cm
Module Type Type2280
English
42
B550M-C
Step 3
Align and gently insert the M.2

(NGFF) SSD module into the M.2
slot. Please be aware that the M.2
(NGFF) SSD module only fits in one
orientation.
A
A 20o
Step 4
Tighten the screw with a screwdriver

to secure the module into place.
Please do not overtighten the screw
as this might damage the module.
NUT2 NUT1
English
43
M.2_SSD (NGFF) Module Support List (M2_2)
Vendor Interface P/N

ADATA SATA3 AXNS330E-32GM-B
ADATA SATA3 ASU800NS38-256GT-C
ADATA SATA3 ASU800NS38-512GT-C
Crucial SATA3 CT120M500SSD4
Crucial SATA3 CT240M500SSD4
Intel SATA3 Intel SSDSCKGW080A401/80G
Kingston SATA3 SM2280S3
Team SATA3 TM4PS4128GMC105
Transcend SATA3 TS256GMTS400
V-Color SATA3 VLM100-120G-2280B-RD
V-Color SATA3 VLM100-240G-2280RGB
V-Color SATA3 VSM100-240G-2280
V-Color SATA3 VLM100-240G-2280B-RD
WD SATA3 WDS100T1B0B-00AS40
WD SATA3 WDS240G1G0B-00RC30
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com
English
44
B550M-C
Chapter 3 Software and Utilities Operation

3.1 Installing Drivers
The Support CD that comes with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard’s features.
Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu does not appear automatically, locate and double click on the file
“ASRSETUP.EXE” in the Support CD to display the menu.
Drivers Menu
The drivers compatible to your system will be auto-detected and listed on the
support CD driver page. Please click Install All or follow the order from top to
bottom to install those required drivers. Therefore, the drivers you install can work
properly.
Utilities Menu
The Utilities Menu shows the application software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
English
45
3.2 ASRock Motherboard Utility (A-Tuning)
ASRock Motherboard Utility (A-Tuning) is ASRock’s multi purpose software suite
with a new interface, more new features and improved utilities.
3.2.1 Installing ASRock Motherboard Utility (A-Tuning)

ASRock Motherboard Utility (A-Tuning) can be downloaded from ASRock Live
Update & APP Shop. After the installation, you will find the icon “ASRock Mother-
board Utility (A-Tuning)“ on your desktop. Double-click the
“ASRock Motherboard Utility (A-Tuning)“ icon, ASRock Motherboard Utility
(A-Tuning) main menu will pop up.
3.2.2 Using ASRock Motherboard Utility (A-Tuning)

There are five sections in ASRock Motherboard Utility (A-Tuning) main menu:
Operation Mode, OC Tweaker, System Info, FAN-Tastic Tuning and Settings.
Operation Mode
Choose an operation mode for your computer.
English
46
B550M-C
OC Tweaker
Configurations for overclocking the system.
System Info
View information about the system.
*The System Browser tab may not appear for certain models.
English
47
FAN-Tastic Tuning
Configure up to five different fan speeds using the graph. The fans will automatically shift
to the next speed level when the assigned temperature is met.
Settings
Configure ASRock ASRock Motherboard Utility (A-Tuning). Click to select "Auto
run at Windows Startup" if you want ASRock Motherboard Utility (A-Tuning) to
be launched when you start up the Windows operating system.
English
48
B550M-C
3.3 ASRock Live Update & APP Shop

The ASRock Live Update & APP Shop is an online store for purchasing and
downloading software applications for your ASRock computer. You can quickly and
easily install various apps and support utilities. With ASRock Live Update & APP
Shop, you can optimize your system and keep your motherboard up to date simply
with a few clicks.
Double-click on your desktop to access ASRock Live Update & APP Shop
utility.
*You need to be connected to the Internet to download apps from the ASRock Live Update & APP Shop.
3.3.1 UI Overview
Category Panel Hot News
Information Panel
Category Panel: The category panel contains several category tabs or buttons that
when selected the information panel below displays the relative information.
Information Panel: The information panel in the center displays data about the
currently selected category and allows users to perform job-related tasks.
English
Hot News: The hot news section displays the various latest news. Click on the image
to visit the website of the selected news and know more.
49
3.3.2 Apps
When the "Apps" tab is selected, you will see all the available apps on screen for you
to download.
Installing an App
Step 1
Find the app you want to install.
The most recommended app appears on the left side of the screen. The other various
apps are shown on the right. Please scroll up and down to see more apps listed.
You can check the price of the app and whether you have already intalled it or not.
- The red icon displays the price or "Free" if the app is free of charge.
- The green "Installed" icon means the app is installed on your computer.
Step 2
Click on the app icon to see more details about the selected app.
English
50
B550M-C
Step 3
If you want to install the app, click on the red icon to start downloading.
Step 4
When installation completes, you can find the green "Installed" icon appears on the
upper right corner.
To uninstall it, simply click on the trash can icon .

English
*The trash icon may not appear for certain apps.
51
Upgrading an App
You can only upgrade the apps you have already installed. When there is an
available new version for your app, you will find the mark of "New Version"
appears below the installed app icon.
Step 1
Click on the app icon to see more details.
Step 2
Click on the yellow icon to start upgrading.

English
52
B550M-C
3.3.3 BIOS & Drivers
Installing BIOS or Drivers

When the "BIOS & Drivers" tab is selected, you will see a list of recommended or
critical updates for the BIOS or drivers. Please update them all soon.
Step 1
Please check the item information before update. Click on to see more details.
Step 2
Click to select one or more items you want to update.
Step 3
Click Update to start the update process.

English
53
3.3.4 Setting
In the "Setting" page, you can change the language, select the server location, and
determine if you want to automatically run the ASRock Live Update & APP Shop
on Windows startup.
English
54
B550M-C
3.4 ASRock Polychrome SYNC

ASRock Polychrome SYNC is a lighting control utility specifically designed for unique indi-
viduals with sophisticated tastes to build their own stylish colorful lighting system. Simply by
connecting the LED strip, you can customize various lighting schemes and patterns, including
Static, Breathing, Strobe, Cycling, Music, Wave and more.
Connecting the LED Strip

Connect your RGB LED strips to the RGB LED Headers (RGB_LED1, RGB_LED2) on the
motherboard.
RGB_LED1
1 B
R
G
12V
RGB_LED2
1
12V G R B
1. Never install the RGB LED cable in the wrong orientation; otherwise, the cable
may be damaged.
2. Before installing or removing your RGB LED cable, please power off your system
and unplug the power cord from the power supply. Failure to do so may cause dam-
ages to motherboard components.
1. Please note that the RGB LED strips do not come with the package.
2. The RGB LED header supports standard 5050 RGB LED strip (12V/G/R/B), with a
maximum power rating of 3A (12V) and length within 2 meters.
English
55
Connecting the Addressable RGB LED Strip
Connect your Addressable RGB LED strips to the Addressable LED Headers (ADDR_LED1,
ADDR_LED2) on the motherboard.
ADDR_LED1
ADDR_LED2
1
GND
DO_ADDR
VOUT
1. Never install the RGB LED cable in the wrong orientation; otherwise, the cable
may be damaged.
2. Before installing or removing your RGB LED cable, please power off your system
and unplug the power cord from the power supply. Failure to do so may cause dam-
ages to motherboard components.
1. Please note that the RGB LED strips do not come with the package.
2. The RGB LED header supports WS2812B addressable RGB LED strip (5V/Data/
GND), with a maximum power rating of 3A (5V) and length within 2 meters.
English
56
B550M-C
ASRock Polychrome SYNC Utility
Now you can adjust the RGB LED color through the ASRock Polychrome SYNC Utility.
Download this utility from the ASRock Live Update & APP Shop and start coloring your
PC style your way!
Drag the tab to customize your

preference.
Toggle on/off the

RGB LED switch
Select a RGB LED light effect
from the drop-down menu.
Sync RGB LED effects

for all LED regions of
the motherboard
English
57
Chapter 4 UEFI SETUP UTILITY
4.1 Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your
system. You may run the UEFI SETUP UTILITY by pressing <F2> or <Del> right
after you power on the computer, otherwise, the Power-On-Self-Test (POST) will
continue with its test routines. If you wish to enter the UEFI SETUP UTILITY after
POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the
reset button on the system chassis. You may also restart by turning the system off
and then back on.
Because the UEFI software is constantly being updated, the following UEFI setup
screens and descriptions are for reference purpose only, and they may not exactly
match what you see on your screen.
4.1.1 UEFI Menu Bar

The top of the screen has a menu bar with the following selections:
Main For setting system time/date information
OC Tweaker For overclocking configurations
Advanced For advanced system configurations
Tool Useful tools
H/W Monitor Displays current hardware status
Security For security settings
Boot For configuring boot settings and boot priority

English
Exit Exit the current screen or the UEFI Setup Utility
58
B550M-C
4.1.2 Navigation Keys

Use < > key or < > key to choose among the selections on the menu bar, and
use < > key or < > key to move the cursor up or down to select items, then
press <Enter> to get into the sub screen. You can also use the mouse to click your
required item.
Please check the following table for the descriptions of each navigation key.
Navigation Key(s) Description
+ / - To change option for the selected items
<Tab> Switch to next function
<PGUP> Go to the previous page
<PGDN> Go to the next page
<HOME> Go to the top of the screen
<END> Go to the bottom of the screen
<F1> To display the General Help Screen
<F7> Discard changes and exit the SETUP UTILITY
<F9> Load optimal default values for all the settings
<F10> Save changes and exit the SETUP UTILITY
<F12> Print screen
<ESC> Jump to the Exit Screen or exit the current screen

English
59
4.2 Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and
display the system overview.
English
60
B550M-C
4.3 OC Tweaker Screen

In the OC Tweaker screen, you can set up overclocking features.
Because the UEFI software is constantly being updated, the following UEFI setup
screens and descriptions are for reference purpose only, and they may not exactly
match what you see on your screen.
Overclock Mode(Bus Speed)

Select the overclock mode. Warning! When overclocking also the PCIe, PCI, SATA and
USB busses will be overcloked which may cause instability or failure. Please install an
operating system and the drivers required before overclocking, or else your HDD's may be
undetectable. Overclocking is not supported if the monitor is connected via the onboard
D-Bus/VGA connector.
CPU Frequency and Voltage(VID) Change

If this item is set to [Manual], the multiplier and voltage will be set based on user selection.
Final result is depending on the CPU's capability.
English
CPU Core (Per CCX)

CPU Voltage
Specifies a custom CPU core voltage (mV), Should be combined with a custom CPU core
61
frequency. Power saving features for idle cores (e.g. cc6 sleep) remain active.
CCD0
CCX0 Frequency (MHz)
Use this item to adjust CCX0 Frequency.

CCD1

SoC/Uncore OC Voltage(VID)
Specify the SoC/Uncore voltage (VDD_SOC) in mV to support memory and Infinity Fabric
overclocking. VDD_SOC also determines the GPU voltage on processors with integrated
graphics. “SoC/Uncore OC Mode” needs to be enabled to force this voltage.
CLD0 VDDP Voltage Control

AMD Overclocking Setup VDDP is a voltage for the DDR4 bus signaling (PHY), and it is
derived from your DRAM Voltage (VDDIO_Mem). As a result, VDDP voltage in mV can
approach but not exceed your DRAM Voltage.
CLD0 VDDG CCD Voltage Control

AMD Overclocking Setup VDDG CCD represents voltage for the data portion of the Infinity
Fabric. It is derived from the CPU SoC/Uncore Voltage (VDD_SOC). VDDG can approach
but not exceed VDD_SOC.
CLD0 VDDG IOD Voltage Control

AMD Overclocking Setup VDDG IOD represents voltage for the data portion of the Infinity
Fabric. It is derived from the CPU SoC/Uncore Voltage (VDD_SOC). VDDG can approach
but not exceed VDD_SOC.
English
62
B550M-C
DRAM Information
Load XMP Setting
Load XMP settings to overclock the memory and perform beyond standard
specifications.
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s) inserted
and assign the appropriate frequency automatically. Setting DRAM Frequency can
adjust DRAM Timing.
DRAM Voltage
Configure the voltage for the DRAM Voltage.
Infinity Fabric Frequency and Dividers

AMD Overclocking Setup Set Infinity Fabric frequency (FCLK). Auto: FCLK =
MCLK. Manual: FCLK must be less than or equal to MCLK for best performance in
most cases. Latency penalties are incurred if FCLK and MCLK are mismatched, but
sufficiently high MCLK can negate or overcome this penalty.
DRAM Timing Configuration

External Voltage Settings and Load-line Calibration
CPU Vcore Voltage
Input voltage for the processor by the external voltage regulator.
CPU Load-Line Calibration

CPU Load-Line Calibration helps prevent CPU voltage droop when the system is
under heavy loading.
VDDCR_SOC Voltage
Input voltage for the processor by the external voltage regulator.
VDDCR_SOC Load-Line Calibration

VDDCR_SOC Load-Line Calibration helps prevent VDDCR_SOC voltage droop
when the system is under heavy loading.
VPPM
English
Configure the voltage for the VPPM.
63
2.50V Voltage
Configure the voltage for the 2.50V PROM Voltage.
CPU VDD 1.8V Voltage

Configure the voltage for the CPU VDD 1.8V Voltage. The default value is [Auto].
Save User Default

Type a profile name and press enter to save your settings as user default.
Load User Default

Load previously saved user defaults.
Save User UEFI Setup Profile to Disk

It helps you to save current UEFI settings as an user profile to disk.
Load User UEFI Setup Profile from Disk

You can load previous saved profile from the disk.
English
64
B550M-C
4.4 Advanced Screen

In this section, you may set the configurations for the following items: CPU
Configuration, Onboard Devices Configuration, Storage Configuration, ACPI Con-
figuration, Trusted Computing, AMD CBS, AMD PBS and AMD Overclocking.
Setting wrong values in this section may cause the system to malfunction.
UEFI Configuration
Active Page on Entry
Select the default page when entering the UEFI setup utility.
Full HD UEFI
When [Auto] is selected, the resolution will be set to 1920 x 1080 if the monitor
supports Full HD resolution. If the monitor does not support Full HD resolution,
then the resolution will be set to 1024 x 768. When [Disable] is selected, the
resolution will be set to 1024 x 768 directly.
English
65
4.4.1 CPU Configuration
PSS Support
Use this to enable or disable the generation of ACPI_PPC, _PSS, and _PCT objects.
NX Mode
Use this to enable or disable NX mode.
SVM Mode
When this is set to [Enabled], a VMM (Virtual Machine Architecture)can utilize the
additional hardware capabilities provided by AMD-V. The default value is [Enabled].
Coniguration options: [Enabled] and [Disabled].
SMT Mode
This item can be used to disable symmetric multithreading. To re-enable SMT, a
power cycle is needed after selecting [Auto].
Warning: S3 is not supported on systems where SMT is disabled.
AMD fTPM Switch

Use this to enable or disable AMD CPU fTPM.
English
66
B550M-C
4.4.2 Onboard Devices Configuration
Turn On LED in S5
Turn on LED in the ACPI S5 state.
SR-IOV Support
Enable/disable the SR-IOV (Single Root IO Virtualization Support) if the system
has SR-IOV capable PCIe devices.
UMA Frame buffer Size (Only for processor with integrated graphics)
This item allows you to set the size of the UMA frame buffer.
Gnb HD Audio
Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and
automatically disable it when a sound card is installed.
Front Panel
Enable/disable front panel HD audio.
Restore on AC/Power Loss

English
Select the power state after a power failure. If [Power Off] is selected, the power will
remain off when the power recovers. If [Power On] is selected, the system will start
to boot up when the power recovers.
67
WAN Radio
Configure the WiFi module's connectivity.
BT On/Off
Enable/disable the bluetooth.
PS2 Y-Cable
Enable the PS2 Y-Cable or set this option to Auto.
English
68
B550M-C
4.4.3 Storage Configuration
SATA Mode
AHCI: Supports new features that improve performance.
RAID: Combine multiple disk drives into a logical unit.
SATA Hot Plug

Enable/disable the SATA Hot Plug function.
English
69
4.4.4 ACPI Configuration
Suspend to RAM
It is recommended to select auto for ACPI S3 power saving.
Deep Sleep
Configure deep sleep mode for power saving when the computer is shut down.
PS/2 Keyboard S4/S5 Wakeup Support

Allow the system to be waked up by a PS/2 Keyboard in S4/S5.
USB Keyboard/Mouse Power On

Allow the system to be waked up by an USB Keyboard/Mouse device.
PCIE Devices Power On

Allow the system to be waked up by a PCIE device and enable wake on LAN.
RTC Alarm Power On

Allow the system to be waked up by the real time clock alarm. Set it to By OS to let
it be handled by your operating system.
English
USB Power Delivery in Soft Off State (S5)

If this option is enabled, the USB port will provide power to your devices even when
the system is in Power State S5.
70
B550M-C
4.4.5 Trusted Computing
Security Device Support

Enable or disable BIOS support for security device.
English
71
4.4.6 AMD CBS
The AMD CBS menu accesses AMD specific features.

English
72
B550M-C
4.4.7 AMD PBS
The AMD PBS menu accesses AMD specific features.
English
73
4.4.8 AMD Overclocking
The AMD Overclocking menu accesses options for configuring CPU frequency and
voltage.
English
74
B550M-C
4.5 Tools
Easy RAID Installer

Easy RAID Installer helps you to copy the RAID driver from the support CD to
your USB storage device. After copying the drivers please change the SATA mode to
RAID, then you can start installing the operating system in RAID mode.
SSD Secure Erase Tool

Use this tool to securely erase SSD.
NVME Sanitization Tool

After you sanitize SSD, all user data will be permantly destroyed on the SSD and
cannot be recovered.
Instant Flash
Save UEFI files in your USB storage device and run Instant Flash to update your
UEFI.
English
75
4.6 Hardware Health Event Monitoring Screen
This section allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, fan
speed and voltage.
CPU FAN1 Setting

Select a fan mode for CPU Fan 1, or choose Customize to set 5 CPU temperatures
and assign a respective fan speed for each temperature.
CPU FAN1 Temp Source

Select a fan temperature source for CPU Fan 1.
FAN Configuration
CHA_FAN1/WP Switch
Select CHA_FAN1 or Water Pump mode.
Chassis Fan 1 Control Mode

Select PWM mode or DC mode for Chassis Fan 1 .
Chassis Fan 1 Setting

English
Select a fan mode for Chassis Fan 1, or choose Customize to set 5 CPU temperatures
76
B550M-C
Chassis Fan 1 Temp Source

Select a fan temperature source for Chassis Fan 1.
CHA_FAN2/WP Switch



CHA_FAN3/WP Switch



Fan-Tastic
Select a fan mode for Fan, or choose Customize to set 5 CPU temperatures and assign a
respective fan speed for each temperature.
FanTuning
Detect the lowest fan speed in the system. Iy may take 3-5 minutes to complete.
English
77
4.7 Security Screen
In this section you may set or change the supervisor/user password for the system.
You may also clear the user password.
Supervisor Password
Set or change the password for the administrator account. Only the administrator
has authority to change the settings in the UEFI Setup Utility. Leave it blank and
press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to change the
settings in the UEFI Setup Utility. Leave it blank and press enter to remove the
password.
Secure Boot
Enable to support Secure Boot.
English
78
B550M-C
4.8 Boot Screen

This section displays the available devices on your system for you to configure the
boot settings and the boot priority.
Boot From Onboard LAN

Allow the system to be waked up by the onboard LAN.
Setup Prompt Timeout

Configure the number of seconds to wait for the setup hot key.
Fast Boot
Fast Boot minimizes your computer's boot time. In fast mode you may not boot
from an USB storage device.
English
79
CSM (Compatibility Support Module)
CSM
Enable to launch the Compatibility Support Module. Please do not disable unless
you’re running a WHCK test.
Launch PXE OpROM Policy

Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
Launch Storage OpROM Policy

Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
Bootup Num-Lock
Select whether Num Lock should be turned on or off when the system boots up.
Full Screen Logo

English
Enable to display the boot logo or disable to show normal POST messages.
80
B550M-C
AddOn ROM Display

Enable AddOn ROM Display to see the AddOn ROM messages or configure the Ad-
dOn ROM if you’ve enabled Full Screen Logo. Disable for faster boot speed.
English
81
4.9 Exit Screen
Save Changes and Exit

When you select this option the following message, “Save configuration changes
and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP
UTILITY.
Discard Changes and Exit

When you select this option the following message, “Discard changes and exit
setup?” will pop out. Select [OK] to exit the UEFI SETUP UTILITY without saving
any changes.
Discard Changes
When you select this option the following message, “Discard changes?” will pop
out. Select [OK] to discard all changes.
Load UEFI BIOS Defaults

Load UEFI BIOS Default values for all the setup questions. The F9 key can be used
for this operation.
English
82
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at https://event.asrock.com/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.

Bijsterhuizen 11-11
6546 AR Nijmegen
The Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.

13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name: ASRock Incorporation
Address: 13848 Magnolia Ave, Chino, CA91710
Phone/Fax No: +1-909-590-8308/+1-909-590-1026
hereby declares that the product
Product Name : Motherboard
Model Number : B550M-C
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Representative Person’s Name: James
Signature :
Date : May 12, 2017

EU Declaration of Conformity

For the following equipment:
Motherboard
(Product Name)
B550M-C / ASRock
(Model Designation / Trade Name)
ASRock Incorporation
(Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.)
(Manufacturer Address)
Radio Equipment Directive - 2014/53/EU
■ EN 300 328 V2.2.2
■ EN 301 893 V2.1.1
□ EN 300 330 V2.1.1
EMC Directive - 2014/30/EU

■ EN 301 489-1 V2.2.3 ■ EN 55024:2010/A1:2015
■ EN 301 489-17 V3.2.4 □ EN 55035:2017/A11:2020
□ EN 301 489-3 V2.1.1 ■ EN 61000-4-2:2009
■ EN 55032:2015/A11:2020 ■ EN 61000-4-3:2006/A1:2008/A2:2010
■ EN 61000-3-2:2014 ■ EN 61000-4-4:2012
■ EN 61000-3-3:2013 ■ EN 61000-4-5:2014/A1:2017
■ EN 61000-4-6:2014/AC:2015
■ EN 61000-4-8:2010
■ EN 61000-4-11:2004/A1:2017
Low Voltage Directive - 2014/35/EU

□ EN 62368-1:2014 □ EN 62311:2008
□ EN 62368-1:2014/A11:2017
RoHS Directive - 2011/65/EU

■ (EU) 2015/863 ■ EN 50581:2012
CE marking
(EU conformity marking)
ASRock EUROPE B.V.

(Company Name)
Bijsterhuizen 1111 6546 AR Nijmegen The Netherlands
(Company Address)
Person responsible for making this declaration:
(Name, Surname)
A.V.P
(Position / Title)
September 24, 2021
(Date)

B550M C

Uploaded by

Copyright:

Available Formats

B550M C

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

B550M C

Uploaded by

Copyright:

Available Formats

Version 1.

CALIFORNIA, USA ONLY

ASRock Website: http://www.asrock.com

Operations in the 5.15-5.35GHz band are restricted to indoor usage only.

Radio transmit power per transceiver type

Function Frequency Maximum Output Power (EIRP)

1.3 Motherboard Layout 7

1.4 I/O Panel 9

1.5 WiFi-802.11ac Module and ASRock WiFi 2.4/5 GHz

2.2 Installing the CPU Fan and Heatsink 15

2.3 Installing Memory Modules (DIMM) 23

2.4 Expansion Slots (PCI Express Slots) 27

2.5 Jumpers Setup 29

2.6 Onboard Headers and Connectors 30

2.7 Post Status Checker 35

2.8 CrossFireX TM and Quad CrossFireX TM Operation Guide 36

2.8.1 Installing Two CrossFireX TM-Ready Graphics Cards 36

2.8.2 Driver Installation and Setup 38

2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1) 39

2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2) 42

Chapter 3 Software and Utilities Operation 45

3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 46

3.2.2 Using ASRock Motherboard Utility (A-Tuning) 46

3.3 ASRock Live Update & APP Shop 49

3.3.3 BIOS & Drivers 53

3.4 ASRock Polychrome SYNC 55

Chapter 4 UEFI SETUP UTILITY 58

4.1.1 UEFI Menu Bar 58

4.1.2 Navigation Keys 59

4.2 Main Screen 60

4.3 OC Tweaker Screen 61

4.4 Advanced Screen 65

4.4.1 CPU Configuration 66

4.4.2 Onboard Devices Configuration 67

4.4.3 Storage Configuration 69

4.4.4 ACPI Configuration 70

4.4.5 Trusted Computing 71

4.4.6 AMD CBS 72

4.4.7 AMD PBS 73

4.4.8 AMD Overclocking 74

4.6 Hardware Health Event Monitoring Screen 76

4.7 Security Screen 78

4.8 Boot Screen 79

4.9 Exit Screen 82

In this documentation, Chapter 1 and 2 contains the introduction of the

1.1 Package Contents

Platform • Micro ATX Form Factor

CPU • Supports AMD AM4 Socket Ryzen™ 3000, 3000 G-Series,

Chipset • AMD B550

Memory • Dual Channel DDR4 Memory Technology

3200/2933/2667/2400/2133 ECC & non-ECC, un-buffered

• AMD Ryzen series APUs (Picasso) support DDR4

Expansion AMD Ryzen series CPUs (Vermeer and Matisse)

* Supports NVMe SSD as boot disks

* The Max shared memory 16GB requires 32GB system

Audio • 7.1 CH HD Audio (Realtek ALC897 Audio Codec)

LAN • PCIE x1 Gigabit LAN 10/100/1000 Mb/s

Wireless • Intel® 802.11ac WiFi Module

Rear Panel • 2 x Antenna Ports