Op and Tech-Gen2-Uni RS232 MNL-000032

Operators and Technicians Manual
PSA-66-ST2RU Printer
GEN2 Universal™
PSA-66-ST2RU (RS232/USB)
While PSA-66-ST2 refers to all models of the printer, the content of this manual is primarily for the RS232/USB
interface of the GEN2 Universal printer.
This document is uncontrolled when printed.

PSA-66-ST2RU Printer (GEN2 Universal™)
© 2006 – 2007 FutureLogic, Incorporated. All Rights Reserved.
TCL Printer Language © 1991 – 2007 FutureLogic, Incorporated. All Rights Reserved.
TCL Printer Language is a proprietary, copyrighted language developed by FutureLogic, Incorporated
for exclusive use with its printer products.
GEN2 Powered by FutureLogic, GEN2, GEN2 Universal, TCL, ITH, TRT, TCL Editor, FutureLogic
Exchange, and FutureLogic are either trademarks or registered trademarks of
FutureLogic, Incorporated in the United States and/or other countries.
Microsoft, Windows, and Windows NT are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Molex is a registered trademark of Molex Incorporated. All product names referenced herein are
trademarks of Molex, its affiliates, related companies, licensors, and/or joint venture partners.
All other trademarks and products or brand names mentioned herein are the property of their
respective owners.
This document contains Proprietary and Confidential information. Its contents are covered by
Non-Disclosure Agreement.
Technical information in this manual is disclosed for informational purposes only.
No grant of license or use rights of any such information is made by publication or distribution of
this manual.
No part of this guide may be reproduced, stored in a retrieval system, or transmitted, in any form or
by any means, electronic, mechanical, recording, or otherwise, without the prior written permission
of FutureLogic, Incorporated.
These specifications are subject to change without notice and may not completely and correctly
document the operation of this product.
12/06/2007
MNL-000032
REV.X07
The printer described in this manual is in compliance with all applied CE standards.
This document describes product functions and technology that may not be available in a particular
gaming jurisdiction, and would therefore not be available for sale and not approved for use at this
time. Please contact your local sales representative for information concerning what features are
available in your jurisdiction.
FutureLogic, Inc.
425 East Colorado Street • Suite 100
Glendale, CA 91205 USA
Phone 818.244.4700 • Fax 818.244.4764
www.futurelogic-inc.com • [email protected]
Table of Contents
1 Product Overview ....................................................................................................1
Introduction .......................................................................................................................1
Warranty Information .........................................................................................................1
2 Operator Interface...................................................................................................2
Introduction .......................................................................................................................2
Operator Indicators and Controls........................................................................................2
Keypad Status Light......................................................................................................3
Bezel Operation.............................................................................................................3
Printer Sensor Functions ....................................................................................................3
Printer Errors .....................................................................................................................4
Loading Paper.....................................................................................................................4
Feeding Paper .....................................................................................................................5
Performing a Self Test .........................................................................................................5
Clearing a Paper Jam..........................................................................................................6
Cleaning the Print Head......................................................................................................7
3 Printer Service...........................................................................................................8
Introduction .......................................................................................................................8
Removing the Printer ..........................................................................................................9
4 Ports .........................................................................................................................11
Introduction ..................................................................................................................... 11
Front Bezel Port ................................................................................................................ 11
PSA-66-ST2RU (GEN2 Universal Printer) .......................................................................... 12
USB/RS232 Interface Cable ........................................................................................ 12
Firmware Upload Port .................................................................................................14
Appendix A Technical Specifications .................................................................... 15
Appendix B Paper Specifications............................................................................ 17
Appendix C Part Numbers – Printer/Spares ........................................................... 18
Appendix D Schematics .......................................................................................... 22
Index .......................................................................................................................... 24
© 2006 – 2007 FutureLogic, Incorporated. All Rights Reserved. MNL Page i of 30 12/06/2007
MNL-000032 REV.X07
List of Figures
Figure 2-1 Operator Indicators and Controls.......................................................................2
Figure 2-2 Load a Paper Stack ............................................................................................5
Figure 2-3 Feed Paper into Paper Loading Slot....................................................................5
Figure 2-4 Sample Configuration Ticket..............................................................................6
Figure 2-5 Remove the Paper ..............................................................................................6
Figure 2-6 Open the Lid......................................................................................................7
Figure 2-7 Clear the Paper Jam ..........................................................................................7
Figure 3-1 Ground Screw and Copper Grounding Clips Location ........................................8
Figure 3-2 Disconnect the Coiled Cable Connector .............................................................9
Figure 3-3 Slide the Printer until It Locks ...........................................................................9
Figure 3-4 Remove the Paper ............................................................................................10
Figure 3-5 Front Locking Bar............................................................................................10
Figure 3-6 Push Release Bar.............................................................................................10
Figure 4-1 Front Bezel LED Control Port........................................................................... 11
Figure 4-2 USB/RS232 Interface Cable............................................................................. 12
Figure 4-3 Firmware Upload Port ......................................................................................14
Figure B-1 Ticket Dimensional Specification ..................................................................... 17
List of Tables
Table 2-1 Keypad LEDs Status Reporting Printer Condition ..............................................3
Table 2-2 Bezel Display Status ..........................................................................................3
Table 2-3 Sensors..............................................................................................................3
Table 2-4 Errors and Error Descriptions............................................................................4
Table 4-1 Front Bezel LED Control Port Pins ...................................................................11
Table 4-2 Base Port Cable Pin-outs ................................................................................. 13
Table 4-3 RS232 Power/COMM Port Pin-out ................................................................... 13
Table 4-4 USB Port Cable Pin-outs ..................................................................................13
Table 4-5 Bezel LED Control Port Pin-out........................................................................13
Table 4-6 Auxiliary COMM Port Pin-out........................................................................... 13
© 2006 – 2007 FutureLogic, Incorporated. All Rights Reserved. MNL Page ii of 30 12/06/2007
MNL-000032 REV.X07
1 Product Overview
Introduction
Each GEN2 Universal™ printer is an advanced thermal printer capable of creating high quality
complex output with a minimum of development and effort on the part of the user.
Note: While PSA-66-ST2 refers to all models of the printer, the content of this manual is
primarily for the RS232/USB interface of the GEN2 Universal printer (PSA-66-ST2RU).
Features of the GEN2 Universal printer include:
• The ITH™ (Intelligent Ticket Handling) technology which prevents player interference with
any part of ticket production or presentation
• May be mounted on an angle or horizontally
• Simple paper loading—no loose parts
• Variable paper capacity with different paper trays—300, 600, and 900 ticket trays
• Windows® ticket/receipt development package via the TCL™ Editor utility
• Page mode printing with TCL printer language
• Line printer capability
• High quality laser-like san serif fonts in multiple sizes
• Advanced graphics printing
• Windows connectivity
• 3 inch per second print speed
• Wide temperature range operation
• Standard and customized serial interfaces available—RS232 and USB
Additionally, a key feature of the GEN2 Universal printer is Universal Communications:
• USB 2.0 Full Speed (Future GSA Compliant, IGT Compliant)
• RS232 Port (Backward Compatible)
Warranty Information
Each printer has a two-year warranty as per the manufacturer’s written warranty.
© 2006 – 2007 FutureLogic, Incorporated. All Rights Reserved. MNL Page 1 of 30 12/06/2007
MNL-000032 REV.X07
2 Operator Interface
Introduction
This chapter covers various operations of the printer including loading paper and clearing a
paper jam.
Operator Indicators and Controls

The printer is equipped with status indicators and a FEED button, which allow you to manage and
interpret the operations of the printer.
The status indicators are:
• The front bezel light
• Keypad lights:
• Ready – Green
• Paper – Yellow
• Open – Orange
• Fault – Red
The following figure illustrates the location of these indicators and controls.
Lid
Release
Lever
Status Lights
and Keypad
Paper
with FEED
Loading Slot
button
Figure 2-1 Operator Indicators and Controls
MNL-000032 REV.X07
Keypad Status Light

The keypad LEDs report the status of the printer whenever power is present. Table 2-1 lists each
condition of the keypad LEDs.
Table 2-1 Keypad LEDs Status Reporting Printer Condition

Condition Ready Paper Open Fault
Unit is Powered Off
Unit Ready blink
Unit Flushed
Paper Out
Head Up or Ticket Module Open
Temperature Error
Voltage Error
Print Head Error
Missing Black Index Mark
Paper is Jammed blink
Indicates the LED is ON.
Bezel Operation
Use the front bezel display to determine the state of the printer while on the casino floor, at a
distance, without disturbing the game. Table 2-2 lists the conditions indicated on the bezel display.
Table 2-2 Bezel Display Status

Bezel Display Status
Solid On Printer Idle and Ready
Slow Blink Paper Low or Printer Error
Fast Blink Ticket Printing and/or Ticket in Chute
Off Printer power off
See Chapter 4 for information on the current ratings of the bezel ports.
Printer Sensor Functions

There are six primary sensor functions on the printer. These sensors work with the game firmware
to provide reliable trouble-free operation. Any error conditions resulting from these sensors are
indicated by the front bezel light and keypad LEDs. Table 2-3 describes each of these sensors.
Table 2-3 Sensors

Sensor Description
Paper Out The Paper Out sensor is located in the print head. It terminates the print operation when the
paper has run out and checks for proper form registration. The printer ceases printing and
feeding operations when it detects a Paper Out condition. Correct a Paper Out condition by
loading more paper into the unit.
Paper Low The Paper Low sensor is located in the paper well. It determines when the paper stack has
approximately 14 tickets remaining. A Paper Low condition automatically resets once a stack
with a greater height is loaded. Paper low sensing occurs when the system is idle and takes a
few seconds to detect the new paper level.
Paper Taken The Paper Taken sensor is located in the presentation chute of the printer. It determines
when the customer has actually taken their cashout ticket.
Drawer Open The Drawer Open sensor is located in the paper well. It detects when the printer is open.
Platen Engaged The Platen Engaged sensor is located in the print head. It detects when the printer platen
is in use.
Printer Open The Printer Open sensor is located in the front of the unit. It detects when the printer
clamshell is open.
MNL-000032 REV.X07
Printer Errors
Although there are a variety of error conditions that can occur, most printer errors are a result of the
printer running out of paper or the operator opening the lid. Table 2-4 lists possible errors and the
remedy for each condition.
Table 2-4 Errors and Error Descriptions

Error Error Description Remedy
Paper Out Results when the printer does not detect paper present. Load a new paper stack.
Head Up or Results from raising the head release lever or opening Lower the blue lever on the side
Open the lid. of the unit.
Temperature Results when the printer is operating outside of its The printer will automatically
allowable temperature range. resume operation after the
If the printer is operating in an environment where the detected head temperature falls
ambient temperature is roughly room temperature, this within range.
error would most likely be the result of a hardware problem.
Voltage Results if the printer detects a power supply voltage The printer will automatically
(+24VDC to +25VDC) outside range. resume operation after the
This error could be the result of a poor cable connection. power supply is detected
within range.
Print Head Results when the printer senses an internal error due to The printer will remain in this
connectivity or interfacing problem with the thermal print error state until the power is
head. This can be a result of a cable problem between the cycled or the unit is reset.
main controller board and the printer engine. If the problem persists, the
printer will require service.
Missing Black Results if the paper type selected is indexed paper and while Raise the head release lever
Index Mark feeding paper or printing a black mark is not seen within (presumably to change
approximately 10” of the paper. the paper).
This error alerts the user to the presence of the wrong kind
of paper in the printer or that the paper was inserted in
the wrong direction (so the black mark index is rotated
180 degrees).
Paper Jam Results when the printer detects an error in the paper path Open the printer head and
for presenting the ticket to the customer. inspect for a jammed ticket.
Loading Paper
Generally, the only printer service required is to load new paper stacks. Use the automatic
paper-loading feature to simplify this process to two steps: putting the paper stack into the Paper
Tray and feeding the paper to the Paper Loading Slot of the printer.
To load paper:
1. Pull open the Printer Drawer until the Paper Tray is completely accessible.
2. Place the paper stack in the printer as indicated by the band around the stack and the label on
the bottom of the Paper Tray.
Tip: To prevent a new paper stack from sticking together, fan out the paper after you take
off the band.
MNL-000032 REV.X07
Paper Tray
Black Index
Mark
Figure 2-2 Load a Paper Stack

3. Feed the paper into the Paper Loading Slot and release it once the motor engages and the printer
takes hold of the paper.
The printer automatically pulls through a form or two, leaving it registered at the top of a form.
Paper
Loading
Slot
Figure 2-3 Feed Paper into Paper Loading Slot

4. Remove any excess ticket(s) from the printer.
Feeding Paper
The printer is designed to run with black mark indexed paper.
Use the FEED button to feed paper into printer. Press the FEED button to advance the paper to the
top of the next form.
Performing a Self Test

Press the FEED button during power up or reset to run a self test. This self test prints a
configuration ticket if the test passes successfully. The test ticket (illustrated in Figure 2-4) contains
important information on how the unit is configured.
MNL-000032 REV.X07
Model: PSA-66 USB REV A

Model number Firmware: GUU0010432 2006-05-17 Resident ticket template
package version
COMMUNICATION
Interface: USB 2.0 Full Speed
Firmware version
System
communications PRINT CONTROL
setup Darkness Control: +0.0
Black Bar Index: Enabled
Print On Demand: Disabled
Auto Sleep Timer: Off
Print Control Parameters SYSTEM RESOURCES

FLASH -Used: 000000 Amount of memory
-Free: 065536 available for user-
defined font and
LIBRARY INVENTORY graphics storage is
Templates: 0,1,2,3,4,5,6,7,8,9,A,B,z,x indicated by the
Print Regions: 1,2,3,4,5,6,7,8,h,9,A,B,
C,D,E,F,G,I,J,K,L,N,O,P,
“Free” space.
Q,R,S,T,U,Z,X,a,b,c,d,e,
Listing of stored f,g,i,j,k,l,m,n,o,p,q,z,x
Templates, Print Graphics:
Regions and Graphics Fonts: 1,2,3,4,5,7,8,9 List of fonts available
in the printer by TCL
page mode
Figure 2-4 Sample Configuration Ticket
Clearing a Paper Jam

The printer is designed to operate reliably with minimal paper jamming. If you need to clear a paper
jam, follow the instructions below. After you clear a paper jam, perform these steps in reverse to
load paper.
When clearing a paper jam:
• Ensure that all paper paths from the entry point at the back of the paper well, through the
printer, cutter, and the ticket module chute are clear of paper or obstructions.
• Use the Lid Release Lever located on the top of the unit.
• Do not allow a screwdriver or other probing object to come in contact with the printer. This can
cause permanent damage to the printer.
To clear a paper jam:
1. Remove the paper from the printer.
Figure 2-5 Remove the Paper
MNL-000032 REV.X07
2. Open the lid by pressing the Lid Release Lever.

The spring-loaded lid opens, exposing the paper path.
Lid Release
Lever
Figure 2-6 Open the Lid

3. Remove the jammed ticket.
If necessary, access the paper path through the print mechanism by opening the Mechanism
Release Lever.
Mechanism
Release Lever
Voucher Path
Figure 2-7 Clear the Paper Jam

4. Once you clear the jam, reverse these steps to return the printer to a ready state.
5. Load the paper.
Cleaning the Print Head

To clean the print head, use canned air to blow out the paper particles. Then use a lint-free cloth or
cotton swab with isopropyl alcohol to clean the print head.
MNL-000032 REV.X07
3 Printer Service
Introduction
This chapter provides instructions on how to remove the printer to service it outside of the game.
Note: While the printer is hot connectable, it is still a good maintenance procedure to turn
off the power.
Important Information!
Do not remove the ground screw in the rail as it will release the internal nut!
After removing the printer, do not slide the unit on a tabletop or other surface. Doing so will
cause damage to the copper grounding clips on the bottom of the unit.
Ticket
Output
Ground Screw Copper Grounding Clips
Figure 3-1 Ground Screw and Copper Grounding Clips Location
MNL-000032 REV.X07
Removing the Printer

CAUTION!
ESD Sensitive Equipment!
Electronic boards and their components are sensitive to static electricity. Care must be
taken during all handling operations and inspections of this product in order to ensure
product integrity at all times.
Do not handle this product out of its protective enclosure while it is not used for operations
purposes unless it is otherwise protected.
Discharge your clothing before touching the assembly. Discharge tools before use.
Whenever possible, unpack or pack this product only at EOS/ESD safe workstations. Where
a safe workstation is not guaranteed, it is important for the user to be electrically
discharged before touching the product with his/her hands or tools.
To remove the printer from the game:
1. Disconnect the power.
2. Disconnect the Coiled Cable Connector.
CAUTION! The cable is under tension.
Coiled Cable
Connector
Figure 3-2 Disconnect the Coiled Cable Connector

3. Pull the printer out of the game until it locks.
Figure 3-3 Slide the Printer until It Locks
MNL-000032 REV.X07
4. Remove the paper from the printer.
Figure 3-4 Remove the Paper

5. Push the Front Locking Bar unit to unlock the sliding module from stationary module.
Slide the drawer module completely out of the stationary module.
Front
Locking
Bar
Figure 3-5 Front Locking Bar

6. Push the Release Bar (located on the bottom of the unit).
While holding in the Release Bar, gently pull the printer towards you.
Figure 3-6 Push Release Bar
MNL-000032 REV.X07
4 Ports
Introduction
This chapter describes the interface connectors and port pin-outs for the printer. For complete
electrical specifications on these ports, refer to Appendix A in the Developers Manual
(MNL-000033) for the power connector.
Note: While PSA-66-ST2 refers to all models of the printer, the content of this manual is
primarily for the RS232/USB interface of the GEN2 Universal printer (PSA-66-ST2RU).
Front Bezel Port
Bezel LED Control Port
3 2 1
Connector: Molex Micro-Fit 43640-0301

Mate: Molex Micro-Fit 43645-0300
Figure 4-1 Front Bezel LED Control Port

Table 4-1 lists information on the LED bezel port on the printer. This is an open drain
modulated high side drive 25VDC port capable of driving up to a maximum 1.5A.
Table 4-1 Front Bezel LED Control Port Pins

Pin Function
1 Switched 25VDC, 100mA Min
2 BGND
3 Frame (Chassis) Ground
MNL-000032 REV.X07
PSA-66-ST2RU (GEN2 Universal Printer)

USB/RS232 Interface Cable
Base Port
Connector: Molex 43025-1800

Mate: Molex 43045-1812
RS232 Power/COMM Port – 14 Pin
Connector: Molex Mini-Fit Jr. 39-01-3149

Mate: Molex Mini-Fit Jr. 39-01-2140
14 8
7 1
Auxiliary COMM Port

4 3
2 1
Bezel LED Control Port

USB Port (Series A)
USB/RS232 14 Pin Cable P/N 150-00123-100
Figure 4-2 USB/RS232 Interface Cable
MNL-000032 REV.X07
Table 4-2 Base Port Cable Pin-outs
Pin Function
1 RAW BGND
2 D-
3 +13V
4 SWITCHED 24V Table 4-3 RS232 Power/COMM Port Pin-out
5 DTR 232
6 MRESET Pin Function
7 D+ 1 MRESET
8 RAW 24V 2 Netplex TXD
9 RTS 232 3 +12 VDC (RS232 optional)
10 RX2/SCL 4 Netplex RXD
11 TX2/SDA 5 GND
12 RX1/232 6 +24 VDC
13 TX1 232 7 GND
14 TX1 NET 8 +24 VDC
15 RX1 NET 9 Modulated +24VDC
16 OPTO GND 10 GND
17 DGND 11 RS232 RXD
18 +9 – 14V 12 RS232 TXD
13 DTR
14 RTS
Table 4-4 USB Port Cable Pin-outs

Pin Function
1 USB BUS SUPPLY
2 D- Table 4-5 Bezel LED Control Port Pin-out
3 D+
Pin Function
4 GND
1 SWITCHED 24V
2 NO CONNECT
3 GND
Table 4-6 Auxiliary COMM Port Pin-out
Pin Function
1 GND
2 RX2
3 TX2
4 NO CONNECT
MNL-000032 REV.X07
Firmware Upload Port

The Firmware Upload Port upgrades the printer firmware while the printer is still installed and
powered in the game. The printer uploads through its Firmware Upload Port just as it would
through its communications connector at the rear of the printer.
To use this port, slide the printer out until the upload port (shown in the following figure) is
visible. Then plug an appropriate upgrade cable into the printer. This connection may be made
while the power is on.
Firmware Upload Port
Connector: Molex 6717101-000

Mate: USB B Plug
Figure 4-3 Firmware Upload Port
MNL-000032 REV.X07
Appendix A Technical Specifications

This appendix identifies the general specifications of the printer.
General
Dimensions (WxDxH) 110 x 304.8 x 64.3 mm
Weight 2.7 lbs.
Power Requirements 24VDC @ 2.7A avg. (4.0A peak with 60% gaming ticket)
Sensors Paper Low, Paper Out, Printer Drawer Open, Ticket Taken, Ticket Jam, Ticket
in Chute, Black Mark
(Includes a Host Controllable Buzzer)
Printing Speed 90mm/Second (3.5”/Second)
Print and Present 2.2 Seconds
Printing Width 62mm (true near-edge printing)
Storage 300 Tickets
Ticket Tray Extenders Interchangeable, 600, 900 Ticket Tray
Resolution 8 dots/mm (203 dpi)
Firmware Application in Memory is Reprogrammable (via Flash BIOS)
Self Test Yes
Page Mode Full Page Mode Printing (Simultaneous 4 Orientation Printing:
0°, 90°, 180°, 270°)
Line and Box Draw Printer Resident
Bitmap Graphics
Printer Resident (Stored in Flash) Graphics
Paper Loading Automatic Hands Free
Paper Feed Manual
Method Direct Thermal, Top Coated, Fanfolded and Perforated
Width 64mm
Length 156mm
Thickness 4.5 mil, 1 Color/2 Colors
Bezel Control Two High Current Ticket Printing Bezel Control Ports
User Interface 4 LED Indicators, Paper Advance Button
Update Port Allows for Printer Upgrades via Handheld Download Tool
Hot Swappable 100%
Printing Resources
Template Capacity 8Mb; Stores hundreds of clip art objects & thousands of graphic
templates
Graphic Storage 6Mb
Color Printing Red on Black and Blue on Black are available. Other colors can be supported
as the print media becomes available. Color selection is controlled through
the TCL language.
MNL-000032 REV.X07
Characteristics
Printer Languages TCL Printer Language (Page Description Language)
Subset of ESCP2
Fonts 8 (2.5 cpi, 3.3 cpi, 4.0 cpi, 5.5 cpi, 5.6 cpi, 7.3 cpi, 10.1 cpi, 20.5 cpi)
Font Scalability May Be Independently Scaled from 1x – 7x in Both Height and Width
Bar codes Interleaved 2 of 5, Code 39, UPC-A, UPC-E, UPC-E+2, UPC-E+5, Codabar,
EAN-13, EAN-8, Code 128, MSI
Memory 2MB with 512k RAM
Interface
Communications USB 2.0 game interface (full speed of 12Mbps) with separate
USB Download Port, Future GSA Compliant,
Compliant with IGT Gaming Machines
A Traditional Game Communication Port (RS232C)
Environmental
Operating temperature 5°C to 65°C
Storage temperature -20°C to 75°C
Operating humidity 5 to 95% RH
Reliability
Maintenance No User Maintenance Required
Printer Completely Removable with Quick Release Bar
Print Head Life 50km Min. (320,000 Tickets Based on US Currency Size)
Certifications CE Certified, ISO 9001, RoHS
MNL-000032 REV.X07
Appendix B Paper Specifications

This appendix provides information on the paper used in the printer. For authorized ticket
converters and complete paper specifications, contact your sales representative or visit our Web
site: www.futurelogic-inc.com.
Note: Use only approved paper in the printer. Use of improper paper may cause
damage to the device and will void the printer’s warranty.
Nominal paper thickness: 4.5mil
Paper dimensions: 65mm x 156mm (width dimension +1mm
Ticket Stack
Ticket, 300STK, 65X156, 5M, Fanfold
Note: Paper width is +0mm, –1mm.
Figure B-1 Ticket Dimensional Specification
MNL-000032 REV.X07
Appendix C Part Numbers – Printer/Spares

This appendix provides the part number and description of the GEN2 Universal printers and
spare parts.
Printers – P/N Description
220-00046-101 GEN2 Universal Printer (RoHS) RoHS Versions—Look
PSA-66-ST2RU for either of these
USB, RS232, Future GSA labels:
Compliant*
Spares – P/N Description

370-00015-100 Base RoHS
370-00170-100 Bottom Chute RoHS
150-00045-100 Cable, Display Adapter RoHS
150-00123-100 Cable, USB-RS232, 14 pin RoHS
370-00021-100 Floating Part RoHS
MNL-000032 REV.X07

370-00024-100 Hinge RoHS
370-00025-100 Hinge Pin RoHS
500-00005-100 Keypad Membrane RoHS
362-00047-102 Lid, Label RoHS
370-00020-100 Lid, Top, Red RoHS
370-00022-100 Locker RoHS
370-00023-100 Locker Base RoHS
370-00016-100 Main Bracket RoHS
140-00099-100 Paper Taken Sensor Board RoHS
140-00100-101 PCBA P9-GEN2 Mother Board RoHS
MNL-000032 REV.X07

460-00005-100 Platen Shaft Assembly RoHS
350-00031-102 Power Supply RoHS
400-00007-100 Print Mech, F03-66 RoHS
310-00112-100 Release Bar Bracket RoHS
310-00115-100 Release Bar Guide RoHS
460-00006-100 Roller Idler RoHS
473-00078-100 Screws (100 pack) RoHS
485-00008-100 Spring (50 pack) RoHS
370-00026-100 Spring Plate RoHS
482-00012-100 Star Washers (100 pack) RoHS
MNL-000032 REV.X07

320-00224-101 Ticket Extension Tray, 600 Tickets RoHS
320-00224-102 Ticket Extension Tray, 900 Tickets RoHS
370-00019-100 Top Presenter RoHS
370-00017-100 Tray, Paper RoHS
MNL-000032 REV.X07
Appendix D Schematics
The schematic included in this appendix is provided solely for use by technicians who service the
GEN2 Universal printer. This information is provided AS IS and without warranty, expressed or
implied.
Note: The information contained in the following schematics is copyrighted information and is
the exclusive intellectual property of FutureLogic, Incorporated. All rights are reserved. No
transfer or grant of rights is created by the publication of this information.
MNL-000032 REV.X07
This information is copyrighted material and is the exclusive intellectual property of FutureLogic, Incorporated. All rights are reserved.
MNL-000032 REV.X07
Index
lid release lever, 2

B
bezel, 3 M
LED control port, 11 mechanism release lever, 7
black mark indexed paper, 5 Missing Black Index Mark error, 3, 4
C P
clearing a paper jam, 6 paper
coiled cable connector, 9 capacity, 1
configuration ticket, 5 feeding, 5
controls, 2 specifications, 17
Paper Jam
D clearing, 6
Drawer Open sensor, 3 error, 3, 4
Paper Low sensor, 3
Paper Out
E
error, 3, 4
errors sensor, 3
Head Up, 4 Paper Taken sensor, 3
Missing Black Index Mark, 4 Platen Engaged sensor, 3
Paper Jam, 4 ports
Paper Out, 4 bezel LED control, 11
Print Head, 4 firmware upload, 14
Temperature, 4 Print Head
Voltage, 4 cleaning, 7
Print Head error, 3, 4
F printer
FEED button, 2, 5 part numbers, 18
Firmware Upload Port, 14 removing, 9
Front Locking Bar, 10 specifications, 15
Printer Open sensor, 3
G
GEN2 Universal R
bezel LED control port, 11 release bar, 10
firmware upload port, 14 removing the printer, 9
specifications, 15 RS232/USB interface cable, 12
H S
Head Up error, 3, 4 schematics, 22
self test, 5
I sensors, 3
indicators, 2 Drawer Open, 3
Paper Low, 3
L Paper Out, 3
Paper Taken, 3
LEDs, 3 sensors (continued)
MNL-000032 REV.X07
Platen Engaged, 3 U
Printer Open, 3 USB/RS232 interface cable, 12
spares, part numbers, 18
status
V
conditions, 3
indicators, 2 Voltage error, 3, 4
T W
TCL Editor, 1 warranty information, 1
Temperature error, 3, 4
test ticket, 5
ticket dimensional specifications, 17
MNL-000032 REV.X07
FutureLogic, Inc.
425 East Colorado Street • Suite 100
Glendale, CA 91205 USA
Phone 818.244.4700 • Fax 818.244.4764
www.futurelogicinc.com • [email protected]

Op and Tech-Gen2-Uni RS232 MNL-000032

Uploaded by

Copyright:

Available Formats

Op and Tech-Gen2-Uni RS232 MNL-000032

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Op and Tech-Gen2-Uni RS232 MNL-000032

Uploaded by

Copyright:

Available Formats

Operators and Technicians Manual

This document is uncontrolled when printed.

Operator Indicators and Controls

Figure 2-1 Operator Indicators and Controls

Keypad Status Light

Table 2-1 Keypad LEDs Status Reporting Printer Condition

Table 2-2 Bezel Display Status

Printer Sensor Functions

Table 2-3 Sensors

Table 2-4 Errors and Error Descriptions

Figure 2-2 Load a Paper Stack

Figure 2-3 Feed Paper into Paper Loading Slot

Performing a Self Test

Model: PSA-66 USB REV A

Print Control Parameters SYSTEM RESOURCES

Clearing a Paper Jam

Figure 2-5 Remove the Paper

2. Open the lid by pressing the Lid Release Lever.

Figure 2-6 Open the Lid

Figure 2-7 Clear the Paper Jam

Cleaning the Print Head

Ground Screw Copper Grounding Clips

Figure 3-1 Ground Screw and Copper Grounding Clips Location

Removing the Printer

Figure 3-2 Disconnect the Coiled Cable Connector

Figure 3-3 Slide the Printer until It Locks

4. Remove the paper from the printer.

Figure 3-4 Remove the Paper

Figure 3-5 Front Locking Bar

Figure 3-6 Push Release Bar

Front Bezel Port

Bezel LED Control Port

Connector: Molex Micro-Fit 43640-0301

Figure 4-1 Front Bezel LED Control Port

Table 4-1 Front Bezel LED Control Port Pins

PSA-66-ST2RU (GEN2 Universal Printer)

Connector: Molex 43025-1800

RS232 Power/COMM Port – 14 Pin

Connector: Molex Mini-Fit Jr. 39-01-3149

Auxiliary COMM Port

Connector: Molex Mini-Fit Jr. 39-01-3049

Bezel LED Control Port

Connector: Molex Mini-Fit Jr. 39-01-4037

USB/RS232 14 Pin Cable P/N 150-00123-100

Figure 4-2 USB/RS232 Interface Cable

Table 4-2 Base Port Cable Pin-outs

Table 4-4 USB Port Cable Pin-outs

Firmware Upload Port

Firmware Upload Port

Connector: Molex 6717101-000

Figure 4-3 Firmware Upload Port

Appendix A Technical Specifications

Appendix B Paper Specifications

Figure B-1 Ticket Dimensional Specification

Appendix C Part Numbers – Printer/Spares

Spares – P/N Description

370-00170-100 Bottom Chute RoHS

150-00045-100 Cable, Display Adapter RoHS

150-00123-100 Cable, USB-RS232, 14 pin RoHS