Scribd
Upload
25 views17 pages

Unit 1

This document discusses several important network analysis theorems including Superposition, Thevenin's, Norton's, and Maximum Power Transfer. It provides details on applying each theorem including determining equivalent resistances and voltages/currents. Procedures and applications of each theorem are described.

Uploaded by

daminikhorwal118
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
25 views17 pages

Unit 1

This document discusses several important network analysis theorems including Superposition, Thevenin's, Norton's, and Maximum Power Transfer. It provides details on applying each theorem including determining equivalent resistances and voltages/currents. Procedures and applications of each theorem are described.

Uploaded by

daminikhorwal118
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

UNIT-1

D C Circuit Analysis and Network Theorems:


 Circuit Concepts: Concepts of network, Active and
passive elements, voltage and current
 sources, source transformation, unilateral and
bilateral elements,
 Kirchhoff’s laws; loop and nodal methods of analysis;
star-delta transformation; Network
 Theorems: Superposition Theorem, Thevenin’s
Theorem, Maximum Power Transfer Theorem.

Electrical Engineering (NEE-101) by Dinesh ,DGI


Introduction

 This chapter introduces important fundamental


theorems of network analysis. They are the
Superposition theorem
Thévenin’s theorem
Norton’s theorem
Maximum power transfer theorem
Superposition Theorem
 Used to find the solution to networks with two or
more sources that are not in series or parallel.
 The current through, or voltage across, an
element in a network is equal to the algebraic sum
of the currents or voltages produced
independently by each source.
 Since the effect of each source will be determined
independently, the number of networks to be
analyzed will equal the number of sources.
Superposition Theorem
The total power delivered to a resistive element must
be determined using the total current through or the
total voltage across the element and cannot be
determined by a simple sum of the power levels
established by each source.
Thévenin’s Theorem
Any two-terminal dc network can be
replaced by an equivalent circuit consisting
of a voltage source and a series resistor.
Thévenin’s Theorem
 Thévenin’s theorem can be used to:
Analyze networks with sources that are not in series or parallel.
Reduce the number of components required to establish the
same characteristics at the output terminals.
Investigate the effect of changing a particular component on
the behavior of a network without having to analyze the entire
network after each change.
Thévenin’s Theorem
 Procedure to determine the proper values of RTh and ETh
 Preliminary
1. Remove that portion of the network across which the
Thévenin equation circuit is to be found. In the figure
below, this requires that the load resistor RL be
temporarily removed from the network.
Thévenin’s Theorem
2. Mark the terminals of the remaining two-terminal network.
(The importance of this step will become obvious as we
progress through some complex networks.)

RTh:
3. Calculate RTh by first setting all sources to zero (voltage
sources are replaced by short circuits, and current sources by
open circuits) and then finding the resultant resistance
between the two marked terminals. (If the internal resistance
of the voltage and/or current sources is included in the
original network, it must remain when the sources are set to
zero.)
Thévenin’s Theorem

ETh:
4. Calculate ETh by first returning all sources to their original
position and finding the open-circuit voltage between the
marked terminals. (This step is invariably the one that will
lead to the most confusion and errors. In all cases, keep in
mind that it is the open-circuit potential between the two
terminals marked in step 2.)
Thévenin’s Theorem
 Conclusion:
Insert Figure 9.26(b)
5. Draw the Thévenin
equivalent circuit with
the portion of the circuit
previously removed
replaced between the
terminals of the
equivalent circuit. This
step is indicated by the
placement of the resistor
RL between the
terminals of the
Thévenin equivalent
circuit.
Thévenin’s Theorem
Experimental Procedures
 Two popular experimental procedures for
determining the parameters of the Thévenin
equivalent network:
 Direct Measurement of ETh and RTh
 For any physical network, the value of ETh can be determined
experimentally by measuring the open-circuit voltage across the
load terminals.
 The value of RTh can then be determined by completing the
network with a variable resistance RL.
Thévenin’s Theorem
 Measuring VOC and ISC
 The Thévenin voltage is again determined by measuring the
open-circuit voltage across the terminals of interest; that is,
ETh = VOC. To determine RTh, a short-circuit condition is
established across the terminals of interest and the current
through the short circuit (Isc) is measured with an ammeter.
Using Ohm’s law:

RTh = Voc / Isc


Norton’s Theorem
 Norton’s theorem states the following:
 Any two-terminal linear bilateral dc network can be
replaced by an equivalent circuit consisting of a current and
a parallel resistor.
 The steps leading to the proper values of IN and RN.
 Preliminary steps:
1. Remove that portion of the network across which the
Norton equivalent circuit is found.
2. Mark the terminals of the remaining two-terminal network.
Norton’s Theorem
 Finding RN:
3. Calculate RN by first setting all sources to zero (voltage
sources are replaced with short circuits, and current sources
with open circuits) and then finding the resultant resistance
between the two marked terminals. (If the internal
resistance of the voltage and/or current sources is included
in the original network, it must remain when the sources are
set to zero.) Since RN = RTh the procedure and value
obtained using the approach described for Thévenin’s
theorem will determine the proper value of RN.
Norton’s Theorem
 Finding IN :
4. Calculate IN by first returning all the sources to their
original position and then finding the short-circuit current
between the marked terminals. It is the same current that
would be measured by an ammeter placed between the
marked terminals.
 Conclusion:
5. Draw the Norton equivalent circuit with the portion of the
circuit previously removed replaced between the terminals
of the equivalent circuit.
Maximum Power Transfer Theorem
 The maximum power transfer theorem
states the following:
A load will receive maximum power from a
network when its total resistive value is
exactly equal to the Thévenin resistance of
the network applied to the load. That is,
RL = RTh
Maximum Power Transfer Theorem
 For loads connected directly to a dc
voltage supply, maximum power will be
delivered to the load when the load
resistance is equal to the internal
resistance of the source; that is, when:

RL = Rint

You might also like