CATALOGUE BUTT WELD FITTINGS

Dimension : ANSI B16.9, B16.25, B16.28, MSS SP-43, SP-48, SP-59

Material Spec. : ASTM A403, A240, A312, A234 WPB
Material Grades : 304, 304L, 316, 316L, CARBON STEEL

90° ELBOW 45° ELBOW 180° ELBOW

EQUAL TEE REDUCING TEE CAP

CON. REDUCER ECC. REDUCER

 Long and Short Radius 45°/ 90° Elbows

ANSI B16.9 B16.28 (in mm)

* Wellgrow’s standard.
Center to End
Nominal Outside Diameter
Long Radius Elbows Short Radius Elbows
Pipe Size at Bevel
(NPS) D 90 degree. 45 degree 90 degree 45 degree
A B A B
1/2 21.3 38.1 15.7 - -
3/4 26.7 38.1 19.1 - -
1 33.4 38.1 22.4 25.4 -
1-1/4 42.2 47.8 25.4 31.8 -
1-1/2 48.3 57.2 28.4 38.1 -
2 60.3 76.2 35.1 50.8 -
2-1/2 73.0 95.2 44.4 63.5 -
3 88.9 114.3 50.8 76.2 31.6
3-1/2 101.6 133.4 57.2 88.9 36.8
4 114.3 152.4 63.5 101.6 42.1
5 141.3 190.5 79.2 127.0 52.6
6 168.3 228.6 95.2 152.4 63.4
8 219.1 304.8 127.0 203.2 84.2
10 273.1 381.0 158.8 254.0 105.2
12 323.9 457.2 190.5 304.8 126.3
14 355.6 533.4 222.2 355.6 147.3
16 406.4 609.6 254.0 406.4 168.3
18 457.2 685.8 285.8 457.2 189.4
20 508.0 762.0 317.5 508.0 210.4
22 558.8 838.2 342.9 558.8 231.5
24 609.6 914.4 381.0 609.6 252.5
26 660.4 990.6 406.4 660.4 273.5
28 711.2 1066.8 438.2 711.2 294.6
30 762.0 1143.0 469.9 762.0 315.6
32 812.8 1219.2 501.6 812.8 378.1
34 863.6 1295.4 533.4 863.6 357.7
36 914.4 1371.6 565.2 914.4 378.8
38 965.2 1447.8 599.9 - -
40 1016.0 1524.0 632.0 1016.0 420.8
42 1066.8 1600.2 660.4 1066.8 441.9
44 1117.6 1676.4 695.5 1117.6 462.9
46 1168.4 1752.6 726.9 - -
48 1219.2 1828.8 759.0 1219.2 505.0
52* 1320.8 - - 1320.8 547.1
54* 1371.6 2057.4 852.2 1371.6 568.1
56* 1422.4 2133.6 883.8 1422.4 589.2
60* 1524.0 2286.0 946.9 1524.0 631.3
66* 1676.4 2514.6 1041.6 - -
68* 1727.0 2591 1073 1727 -
72* 1829.0 2743 1137 1829 -
76* 1930.0 2896 1199 1930 -
80 2032.0 3048 1263 2032 -
 Wall Thickness Schedule

JIS G3448 JIS G3455 ANSI B36.10M

JIS G3454 JIS G3459 ANSI B36.19M (in mm)
Nominal Outside
Nominal Wall Thickness
Pipe Size Diameter
Sch Sch Sch Sch LG Sch Sch Sch Sch Sch Sch Sch Sch Sch
A B JIS ANSI GS STD XS XXS
5S 10S 20S 10 (7.9) 20 30 40 60 80 100 120 140 160
8 1/4 13.8 13.7 1.2 1.65 2.0 2.3 - - - - (2.2) 2.2 2.4 (3.0) 3.0 - - - - -
10 3/8 17.3 17.1 1.2 1.65 2.0 2.3 - - - - (2.3) 2.3 2.8 (3.2) 3.2 - - - - -
15 1/2 21.7 21.3 1.65 2.1 2.5 2.8 - - - - (2.8) 2.8 3.2 (3.7) 3.7 - - - 4.7 7.5
20 3/4 27.2 26.7 1.65 2.1 2.5 2.8 - - - - (2.9) 2.9 3.4 (3.9) 3.9 - - - 5.5 7.8
25 1 34.0 33.4 1.65 2.8 3.0 3.2 - - - - (3.4) 3.4 3.9 (4.5) 4.5 - - - 6.4 9.1
32 1-1/4 42.7 42.2 1.65 2.8 3.0 3.5 - - - - (3.6) 3.6 4.5 (4.9) 4.9 - - - 6.4 9.7
40 1-1/2 48.6 48.3 1.65 2.8 3.0 3.5 - - - - (3.7) 3.7 4.5 (5.1) 5.1 - - - 7.1 10.2
50 2 60.5 60.3 1.65 2.8 3.5 3.8 - - - - (3.9) 3.9 4.9 (5.5) 5.5 - - - 8.7 11.1
65 2-1/2 76.3 73.0 2.1 3.0 3.5 4.2 - - - - (5.2) 5.2 6.0 (7.0) 7.0 - - - 9.5 14.0
80 3 89.1 88.9 2.1 3.0 4.0 4.2 - - - - (5.5) 5.5 6.6 (7.6) 7.6 - - - 11.1 15.2
90 3-1/2 101.6 101.6 2.1 3.0 4.0 4.2 - - - - (5.7) 5.7 7.0 (8.1) 8.1 - - - 12.7 -
100 4 114.3 114.3 2.1 3.0 4.0 4.5 - - - - (6.0) 6.0 7.1 (8.6) 8.6 - 11.1 - 13.5 17.1
125 5 139.8 141.3 2.8 3.4 5.0 4.5 - - - - (6.6) 6.6 8.1 (9.5) 9.5 - 12.7 - 15.9 19.0
150 6 165.2 168.3 2.8 3.4 5.0 5.0 - 5.0** - - (7.1) 7.1 9.3 (11.0) 11.0 - 14.3 - 18.2 21.9
175 7 190.7 - - - - 5.3 - - - - - - - - - - - - - -
200 8 216.3 219.1 2.8 3.8 6.5 5.8 - 5.8** 6.4 7.0 (8.2) 8.2 10.3 (12.7) 12.7 15.1 18.2 20.6 23.0 22.2
225 9 241.8 - - - - 6.2 - - - - - - - - - - - - - -
250 10 267.4 273.1 3.4 4.2 6.5 6.6 - 6.6** 6.4 7.8 (9.3) 9.3 12.7 12.7 15.1 18.3 21.4 25.4 28.6 25.4
300 12 318.5 323.9 4.0 4.6 6.5 6.9 - 6.9** 6.4 8.4 9.5 10.3 14.3 12.7 17.4 21.4 25.4 28.6 33.3 25.4
350 14 355.6 355.6 4.0 4.8 7.9 7.9 6.4 7.9 7.9 9.5 9.5 11.1 15.1 12.7 19.0 23.8 27.8 31.8 35.7 -
400 16 406.4 406.4 4.2 4.8 7.9 7.9 6.4 7.9 7.9 9.5 9.5 12.7 16.7 12.7 21.4 26.2 30.9 36.5 40.5 -
450 18 457.2 457.2 4.2 4.8 7.9 7.9 6.4 7.9 7.9 11.1 9.5 14.3 19.0 12.7 23.8 29.4 34.9 39.7 45.2 -
500 20 508.0 508.0 4.8 5.5 7.9 7.9 6.4 7.9 9.5 12.7 9.5 15.1 20.6 12.7 26.2 32.5 38.1 44.4 50.0 -
550 22 558.8 558.8 4.8 5.5 - - 6.4 7.9 9.5 12.7 9.5 - 22.2 12.7 28.6 34.9 41.3 47.6 54.0 -
600 24 609.6 609.6 5.5 6.4 - - 6.4 7.9 9.5 14.3 9.5 17.5 24.6 12.7 31.0 38.9 46.0 52.4 59.5 -
650 26 660.4 660.4 - - - - 7.9 7.9 12.7 - 9.5 - - 12.7 - - - - - -
700 28 711.2 711.2 - - - - 7.9 7.9 12.7 15.9 9.5 - - 12.7 - - - - - -
750 30 762.0 762.0 6.4 7.9 - - 7.9 7.9 12.7 15.9 9.5 - - 12.7 - - - - - -
800 32 812.8 812.8 - - - - 7.9 7.9 12.7 15.9 9.5 17.5 - 12.7 - - - - - -
850 34 863.6 863.6 - - - - 7.9 7.9 12.7 15.9 9.5 17.5 - 12.7 - - - - - -
900 36 914.4 914.4 - - - - 7.9 7.9 12.7 15.9 9.5 19.1 - 12.7 - - - - - -
950 38 965.2 965.2 - - - - - 7.9 12.7 - 9.5 - - 12.7 - - - - - -
1000 40 1016.0 1016.0 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1050 42 1066.8 1066.8 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1100 44 1117.6 1117.6 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1150 46 1168.4 1168.4 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1200 48 1219.2 1219.2 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1250 50 1270.0 1270.0 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1300 52 1320.8 1320.8 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1350 54 1371.6 1371.6 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1400 56 1422.4 1422.4 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1450 58 1473.2 1473.2 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1500 60 1524.0 1524.0 - - - - - 7.9 - - 9.5 - - 12.7 - - - - - -
1600 64 1626.0
1700 68 1727.0
1800 72 1829.0
1900 76 1932.0
2000 80 2032.0

(1) * Wellgrow’s standard.

(2) **Applied only small end side of the tee and reducers.
(3) The numerical values in parenthesis are the same thickness as Sch. 40 or Sch. 80.
ANSI Dimensional Tolerances
ANSI B16.9, B16.28 (in mm)
* Wellgrow’s standard
90° and 45°
All Fittings Tees Reducers Caps 180° Returns
Elbows
Nominal Outside Inside Wall Center-to-end Center-to-end Overall Overall Center-to- Back-to-face Alignment of
Pipe Size Diameter at Diameter at Thickness Dimension Dimension Length Length center Dimension Ends
Bevel End Dimension
OD ID T A, B C, M H E P K U
+1.5
1/2~2-1/2 ±0.7
-0.7
±3.0
3~4 ±1.5 ±1.5 ±1.5 ±1.5 ±6.3 ±0.7
±1.5
+2.2
5~8 ±6.3
-1.5
+4.0
10~18 ±3.0 ±6.3
-3.0
Not less ±2.2 ±2.2 ±2.2 ±9.6 ±0.7
20~24 than
87.5% of
+6.3 nominal
26~30 ±4.8 ±3.0 ±3.0
-4.8 thickness ±4.8 ±9.6
32~48 ±4.8 ±4.8

+9.5
*50~60 ±6.4 ±9.5 ±9.5 ±9.5 - - -
-6.4
+12.7
*62~70 ±9.5 ±12.7 -
-9.5
- -
+15.9
*72~80 ±11.9 ±15.9
-11.9

Angularity Tolerance
Nominal
Pipe Size Off Angle Off Plane

Q P
1/2~4 0.7 1.5

5~8 1.5 3.0

10~12 4.8
2.2
14~16 6.3

18~24 3.0
9.6
26~30

32~42 4.8 12.7

44~48 19.0

*50~60 6.4

*62~70 9.5

*72~80 11.9
MSS Dimensional Tolerances
MSS SP-43 (in mm)
90° Elbows Reducers
Lap Joint
All Fittings 45°Elbows Lap Joint Caps 180° Returns
Stub Ends
Tees Stub Ends
Nominal
Wall Center-to-end Overall Overall Center-to-center Back-to-face Alignment Fillet (2) Outside
Pipe Size Outside (1)
Thickness Dimension Length Length Dimension Dimension of Ends Radius Diameter
Diameter at
of Lap of Lap
Welding End
A, B, C, M F, H E O K U A G
+0 +0
1/2~1-1/2 ±0.8 ±1.6 ±1.6 ±3.0 ±6.4 ±6.4 ±0.8
-0.8 -0.8
+0 +0
2~3-1/2 ±0.8 ±1.6 ±1.6 ±3.0 ±6.4 ±6.4 ±0.8
-0.8 -0.8
Not less than +0 +0
4 ±0.8 ±1.6 ±1.6 ±3.0 ±6.4 ±6.4 ±0.8
87.5% of -1.6 -0.8
+1.6 nominal +0 +0
5~8 thickness ±1.6 ±1.6 ±6.4 ±6.4 ±6.4 ±0.8
-0.8 -1.6 -0.8
+2.3 +0 +0
10~18 ±2.3 ±2.3 ±6.4 ±9.7 ±6.4 ±1.6
-0.8 -1.6 -1.6
+3.0 +0 +0
20~24 ±2.3 ±2.3 ±6.4 ±9.7 ±6.4 ±1.6
-0.8 -1.6 -1.6

(1) Out of roundness is the vector sum of the plus and minus tolerance.
(2) Fillet B radius is the maximum.

MSS Dimensional Tolerances

MSS SP-75 (in mm)
Out-of-roundness (2) 90°, 60°, 45°, 30° Elbows Reducers Caps Angularity Elbows Eccentric and
Inside (1) Minimum (3) & Tees Overall Overall Off Angle Off Concentric
Nominal Center-to-end Dimension Length
Diameter Wall At Ends of fittings Throughout (4) Length Plane Reducers Off
Pipe Size A, B, C, M
at End Thickness Body of Elbows Plane
Elbows (5) Other 1-1/2R & Tee 3R H E Q P P (6)
16~24 ±2.3 Nominal 4.8 3.0 2.5% ±2.3 ±3.0 ±2.3 ±6.4 1.5 6.4 2.5%
26~36 ±2.3 -0.25 (5) 3.0 2.5% ±3.0 ±6.4 ±4.8 ±9.6 2.3 12.7 2.5%
38~48 ±3.0 (5) 3.0 2.5% ±4.8 ±9.6 ±9.6 ±9.6 3.0 19.1 2.5%

(1) The inside diameter at end shall be determined by circumferential

measurement, and the tolerance refers to variations from nominal I.D.
2t
calculation by (OD nom- nom).
(2) Out-of-roundness tolerances shall be the difference between the
maximum and minimum diameters measured on any radial
cross-section.
(3) Minus 0.01 in. except that isolated non-continuous reductions are
permitted in accordance with subsection 13.2.1. Excess thickness
whether on inside or outside is to be treated in accordance with sketch
given in figure 3.
(4) When elbows are intended for field segmenting, out-of-roundness
tolerance may be furnished to 1% by agreement between the
manufacturer and the purchaser. It is recognized that extra thickness, if
any, may be on the I.D.
(5) Out-of-roundness tolerances at ends shall be 1% of diameter for NPS
26 and larger.
(6) Percent of O.D.

Outside diameter may be tapered at angle up to 30° beyond weld bevel.

 Weld End Preparation

(a) Plain bevel (b) Compound bevel

Nominal Pipe Wall Thickness (t) End Preparation

Less than x* Cut square or slightly chamfer, at manufacturer’s option

X* to 22 included Plain bevel as in sketch “a” above

More than 22 Compound bevel as in sketch “b” above

X*= 5 for carbon steel, ferritic alloy steel or wrought iron;

4 for austenitic alloy steel
(in mm)
Notes:
(1) End preparations are in accordance with ANSI B16.25 Paragraph 4.2.
(2) End preparations conforming to customer specifications will be specially manufactured upon consutation.

MSS SP-75, API 5L